Welcome to minicom 2.7 OPTIONS: I18n Compiled on Nov 15 2018, 20:18:47. Port /dev/ttyUSB3, 14:58:24 Press CTRL-A Z for help on special keys Power off the system Low Voltage detected on KL30_Power �� [0000.022] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet lev. [0000.030] I> MB1 (prd-version: s_1.6.0.0-t194-41334769-fac5b753) [0000.036] I> Boot-mode: Coldboot [0000.039] I> Chip revision : A02 [0000.042] I> Bootrom patch version : 15 (correctly patched) [0000.047] I> ATE fuse revision : 0x200 [0000.051] I> Ram repair fuse : 0x0 [0000.054] I> Ram Code : 0x1 [0000.056] I> rst_source : 0x0 [0000.059] I> rst_level : 0x0 [0000.062] I> Boot-device: QSPI [0000.065] I> Qspi flash params source = brbct [0000.069] I> Qspi using bpmp-dma [0000.072] I> Qspi clock source : pllp [0000.076] W> DEVICE_PROD: device prod is not initialized. [0000.081] I> QSPI Flash Size = 64 MB [0000.084] I> Qspi initialized successfully [0000.088] I> Active Boot chain : 0 [0000.091] I> Boot-device: QSPI [0000.094] I> Qspi flash params source = brbct [0000.099] E> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT. [0000.106] E> MB1_PLATFORM_CONFIG: Failed to initialize device prod. [0000.113] I> Temperature = 23000 [0000.116] W> Skipping boost for clk: AON_CPU_NIC [0000.120] W> Skipping boost for clk: CAN1 [0000.124] W> Skipping boost for clk: CAN2 [0000.128] I> Boot-device: QSPI [0000.131] I> Qspi flash params source = mb1bct [0000.135] I> Qspi using bpmp-dma [0000.138] I> Qspi clock source : pllc_out0 [0000.142] W> DEVICE_PROD: device prod is not initialized. [0000.147] I> Qspi reinitialized [0000.152] I> Qspi flash params source = mb1bct [0000.157] I> ECC region[0]: Start:0x0, End:0x0 [0000.161] I> ECC region[1]: Start:0x0, End:0x0 [0000.165] I> ECC region[2]: Start:0x0, End:0x0 [0000.169] I> ECC region[3]: Start:0x0, End:0x0 [0000.173] I> ECC region[4]: Start:0x0, End:0x0 [0000.178] I> Non-ECC region[0]: Start:0x80000000, End:0x880000000 [0000.183] I> Non-ECC region[1]: Start:0x0, End:0x0 [0000.188] I> Non-ECC region[2]: Start:0x0, End:0x0 [0000.192] I> Non-ECC region[3]: Start:0x0, End:0x0 [0000.197] I> Non-ECC region[4]: Start:0x0, End:0x0 [0000.202] W> DEVICE_PROD: device prod is not initialized. [0000.209] W> DEVICE_PROD: device prod is not initialized. [0000.215] W> MB1_PLATFORM_CONFIG: Rail ID 7 not found in pmic rail config tabl. [0000.222] E> FAILED: MEMIO rail config [0000.233] I> scrub mode: full dram [0000.239] I> Boot-device: QSPI [0000.241] I> Qspi flash params source = mb1bct [0000.298] E> MB1_PLATFORM_CONFIG: Bootrom mmio i2c table is empty in MB1 BCT. [0000.307] W> MB1_PLATFORM_CONFIG: Rail ID 8 not found in pmic rail config tabl. [0000.330] I> MB1 done ����main enter SPE VERSION #: R01.00.16 Created: Dec 7 2018 @ 15:56:21 HW Function test Start Scheduler. in late init �� I> Welcome to MB2(TBoot-BPMP) (version: 00.00.2018.32-embedded-8357db87) I> DMA Heap @ [0x526fa000 - 0x52ffa000] I> Default Heap @ [0xd486400 - 0xd48a400] E> DEVICE_PROD: Invalid value data = 70020000, size = 0. W> device prod register failed I> Boot-device: QSPI I> Boot_device: QSPI_FLASH instance: 0 I> QSPI Flash Size = 64 MB I> Qspi initialized successfully I> qspi flash-0 params source = boot args I> Boot-device: QSPI I> Found 21 partitions in QSPI_FLASH (instance 0) I> GR Blob not found or corrupted. Skipping GR Dump for MB1 Stage E> CLK_RST: instance 0 not found in module 23. E> CLK_RST: instance 0 not found in module 22. E> CLK_RST: instance 0 not found in module 24. I> Active Boot chain : 0 I> Relocating BR-BCT I> EKS detected (length: 0x610) @ VA:0x526fba00 I> GR Blob not found or corrupted. Skipping GR Dump for MB2 Stage ��NOTICE: BL31: v1.4(release):b51ed9c NOTICE: BL31: Built : 17:49:25, May 23 2019 �� ���� [0x0000000000FDB6D5] : [ LOG ] : SCE Booted:VERSION:00.03.04 [0x0000000000FDF2A4] : [ LOG ] : 3LSS Version : 1.0.0 [0x0000000000FE3346] : [ LOG ] : Initializing SEC Threshold Done [0x0000000000FE7A54] : [ INFO ] : NOC Bist : Passed����������] ��HV-RT-Core: rc HV-RT-Core: RtWindowUs = : 0x64 HV-RT-Core: RtFwdProgressUs = : 0x14 DRIVE Hypervisor ��MMFLAGS=1 �D-S> �� Starting TrustZone Server... ��platform_guest_warm_boot: guest warm reboot platform_guest_warm_boot: guest warm reboot platform_guest_warm_boot: guest warm reboot platform_guest_warm_boot: guest warm reboot platform_guest_warm_boot: guest warm reboot platform_guest_warm_boot: guest warm reboot ����[ 0.000000] Booting Linux on physical CPU 0x100 ��T��.000000] Linux version 4.14.102-rt53-tegra (buildbrain@mobile-u64-3149) ( ��0���� RT Mon ��m��M��a��ay��i�� ��n��2��:��0 �� ��1��C��4��m��:3��d� ��t����_��[ ��I�� ��n�� ��i�� ��t��0.�� ��0��f��0��a��00��i��0��l��0 ��ocessor [4e0f0040]4 Pr�� [ 0.000000] OF: fdt: memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ff00000 [ 0.000000] OF: fdt: - 100000000 , 6b8000000 [ 0.000000] Machine model: e3550_t194a [ 0.000000] earlycon: uart8250 at MMIO32 0x000000000c280000 (options '') ��ivc id max is 999: Invalid argument ��platform_guest_warm_boot: guest warm reboot ����[ 1.229] Start VM0(Guest OS) to VM_STATE_UNHALT [ 1.234] End VM0(Guest OS) to VM_STATE_UNHALT [ 1.237] Start VM1(Safety service) to VM_STATE_UNHALT [ 1.242] End VM1(Safety service) to VM_STATE_UNHALT ��NVG write denied! MMFLAGS=1 All ClockCycles offsets within tolerance Starting Safety Starting pipe manager... ��platform_guest_warm_boot: guest warm reboot ����[ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'fb0B [ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'fb0B [ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'fb1B [ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'fb1B [ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'fb2B [ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'fb2B [ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'fb3B [ 0.000000] OF: fdt: Reserved memory: failed to reserve memory for node 'fb3B [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible s [ 0.000000] OF: reserved mem: initialized node carveout0, compatible id nvidt [ 0.000000] OF: reserved mem: initialized node generic_carveout, compatible t [ 0.000000] cma: Reserved 512 MiB at 0x000000009fc00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] random: get_random_bytes called from start_kernel+0xb0/0x418 wit0 [ 0.000000] percpu: Embedded 23 pages/cpu @ffffffc737da3000 s54144 r8192 d318 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 7192332 [ 0.000000] Kernel command line: fbcon=map:9 aurixfw=AFW root=/dev/vblkdev0p0 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 4194304 (order: 14, 67108864 by) [ 0.000000] Inode-cache hash table entries: 2097152 (order: 12, 16777216 byt) [ 0.000000] software IO TLB: mapped [mem 0x9bc00000-0x9fc00000] (64MB) [ 0.000000] Memory: 28057860K/29225984K available (14014K kernel code, 2656K) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 ) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 ) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008e30000 ( 14016 ) [ 0.000000] .rodata : 0xffffff8008e30000 - 0xffffff8009320000 ( 5056 ) [ 0.000000] .init : 0xffffff8009320000 - 0xffffff8009a20000 ( 7168 ) [ 0.000000] .data : 0xffffff8009a20000 - 0xffffff8009cb8008 ( 2657 ) [ 0.000000] .bss : 0xffffff8009cb8008 - 0xffffff8009d47818 ( 575 ) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 ) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 ) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 ) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf1ce00000 ( 462 ) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc738000000 ( 29568 ) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 [ 0.000000] ftrace: allocating 43521 entries in 171 pages [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU event tracing is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=6. [ 0.000000] RCU priority boosting: priority 1 delay 500 ms. [ 0.000000] No expedited grace period (rcu_normal_after_boot). [ 0.000000] Tasks RCU enabled. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] arch_timer: cp15 timer(s) running at 31.25MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycless [ 0.000004] sched_clock: 56 bits at 31MHz, resolution 32ns, wraps every 4398s [ 0.000417] Console: colour dummy device 80x25 [ 0.218300] kmemleak: Kernel memory leak detector disabled [ 0.218318] Calibrating delay loop (skipped), value calculated using timer f) [ 0.218350] pid_max: default: 32768 minimum: 301 [ 0.218938] Security Framework initialized [ 0.219327] Mount-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.219404] Mountpoint-cache hash table entries: 65536 (order: 7, 524288 byt) [ 0.237347] ASID allocator initialised with 65536 entries [ 0.269557] Hierarchical SRCU implementation. [ 0.299774] tegra-id: chipid=21917. [ 0.301344] tegra-id: opt_subrevision=0. [ 0.303106] Tegra Revision: A02 SKU: 0x90 CPU Process: 0 SoC Process: 0 [ 0.305859] DTS File Name: /dvs/git/dirty/git-master_modular/kernel/kernel-4s [ 0.313987] DTB Build time: May 20 2019 14:31:03 [ 0.330930] smp: Bringing up secondary CPUs ... [ 0.376455] CPU1: Booted secondary processor [4e0f0040] [ 0.420683] CPU2: Booted secondary processor [4e0f0040] [ 0.464971] CPU3: Booted secondary processor [4e0f0040] [ 0.509526] CPU4: Booted secondary processor [4e0f0040] [ 0.553866] CPU5: Booted secondary processor [4e0f0040] [ 0.554133] smp: Brought up 1 node, 6 CPUs [ 0.566562] SMP: Total of 6 processors activated. [ 0.568403] CPU features: detected feature: Privileged Access Never [ 0.570922] CPU features: detected feature: LSE atomic instructions [ 0.573466] CPU features: detected feature: User Access Override [ 0.575875] CPU features: detected feature: 32-bit EL0 Support [ 0.896785] CPU: All CPU(s) started at EL1 [ 0.898304] alternatives: patching kernel code [ 0.902882] CPU5: update max cpu_capacity 1024 [ 0.910256] CPU2: update max cpu_capacity 1024 [ 0.911759] devtmpfs: initialized [ 0.949348] Initilizing CustomIPI irq domain ��0��0.951106] Registered cp15_barrier emul��[��ati�� ��o�� ��n �� ��ha�� ��n��� ��T����1] ��[��S�� ��t�� ��a�� ��r��0.��t��95�� ��3��V��0��M��29��2��]��(�� R�r ��[����E_UNHALT �� 0.955127] clocksource: jiffies: mask: 0xf��[��f�� ��fff�� ��ff�� ��f� ��i����[ ��t�� ��o��0.�� ��95��V��97��M��69��_��] ��S��fu��T��te��A��x ��T��h� ��es: 2048 (order: 6, 262144 bytes) [ 0.975819] pinctrl core: initialized pinctrl subsystem [ 0.978917] regulator-dummy: no parameters [ 0.981970] tegra_hv: adding ivc256: rx_base=ffffff800a060000 tx_base = ffff) [ 0.985658] tegra_hv: added ivc256 [ 0.986991] tegra_hv: adding ivc257: rx_base=ffffff800a078080 tx_base = ffff) [ 0.990528] tegra_hv: added ivc257 [ 0.991854] tegra_hv: adding ivc248: rx_base=ffffff800a050000 tx_base = ffff) [ 0.995351] tegra_hv: added ivc248 [ 0.996618] tegra_hv: adding ivc249: rx_base=ffffff800a052080 tx_base = ffff) [ 1.000163] tegra_hv: added ivc249 [ 1.001406] tegra_hv: adding ivc246: rx_base=ffffff800a040000 tx_base = ffff) [ 1.004911] tegra_hv: added ivc246 [ 1.006144] tegra_hv: adding ivc247: rx_base=ffffff800a042080 tx_base = ffff) [ 1.009701] tegra_hv: added ivc247 [ 1.010982] tegra_hv: adding ivc244: rx_base=ffffff800a030000 tx_base = ffff) [ 1.014624] tegra_hv: added ivc244 [ 1.015896] tegra_hv: adding ivc245: rx_base=ffffff800a032080 tx_base = ffff) [ 1.019480] tegra_hv: added ivc245 [ 1.020744] tegra_hv: adding ivc242: rx_base=ffffff800a020000 tx_base = ffff) [ 1.024310] tegra_hv: added ivc242 [ 1.025563] tegra_hv: adding ivc243: rx_base=ffffff800a022080 tx_base = ffff) [ 1.029110] tegra_hv: added ivc243 [ 1.030380] tegra_hv: adding ivc240: rx_base=ffffff800a010000 tx_base = ffff) [ 1.034031] tegra_hv: added ivc240 [ 1.035341] tegra_hv: adding ivc241: rx_base=ffffff800a012080 tx_base = ffff) [ 1.038876] tegra_hv: added ivc241 [ 1.040186] tegra_hv: adding ivc238: rx_base=ffffff800a000000 tx_base = ffff) [ 1.043701] tegra_hv: added ivc238 [ 1.044940] tegra_hv: adding ivc239: rx_base=ffffff800a002080 tx_base = ffff) [ 1.048407] tegra_hv: added ivc239 [ 1.049654] tegra_hv: adding ivc287: rx_base=ffffff8009fc0000 tx_base = ffff) [ 1.053138] tegra_hv: added ivc287 [ 1.054378] tegra_hv: adding ivc233: rx_base=ffffff8009f80000 tx_base = ffff) [ 1.057810] tegra_hv: added ivc233 [ 1.059005] tegra_hv: adding ivc13: rx_base=ffffff800a1d0000 tx_base = fffff) [ 1.062401] tegra_hv: added ivc13 [ 1.063657] tegra_hv: adding ivc12: rx_base=ffffff800a1c0000 tx_base = fffff) [ 1.068979] tegra_hv: added ivc12 [ 1.070449] tegra_hv: adding ivc11: rx_base=ffffff800a1b0000 tx_base = fffff) [ 1.073866] tegra_hv: added ivc11 [ 1.075306] tegra_hv: adding ivc10: rx_base=ffffff800a1a0000 tx_base = fffff) [ 1.079592��N��]��VG write de�� ��nied! ��tegra_hv: added ivc10 [ 1.081207] tegra_hv: adding ivc9: rx_base=ffffff800a190000 tx_base = ffffff) [ 1.084619] tegra_hv: added ivc9 [ 1.085759] tegra_hv: adding ivc8: rx_base=ffffff800a180000 tx_base = ffffff) [ 1.089158] tegra_hv: added ivc8 [ 1.090309] tegra_hv: adding ivc7: rx_base=ffffff800a170000 tx_base = ffffff� �� ��[ 1.094379] tegra_hv: added ivc7 [ 1.096740] tegra_hv: adding ivc6: rx_base=ffffff800a160000 tx_base = ffffff) [ 1.100621] tegra_hv: added ivc6 [ 1.101954] tegra_hv: adding ivc5: rx_base=ffffff800a150000 tx_base = ffffff) [ 1.105777] tegra_hv: added ivc5 [ 1.106874] tegra_hv: adding ivc4: rx_base=ffffff800a140000 tx_base = ffffff) [ 1.110359] ��A��te��l��gr��l��a_�� ��hv��C��: ��l��ad��o��de��c��d � ��ff��[��e�� ��s�� �� �� 1��o��.1��f��11��f��53��s��6]��e�� t��t��eg ��f800a130000 tx_base = ffffff800a130100 size=100 irq = 31 (476) [ 1.115126] tegra_hv: added ivc3 [ 1.116441] tegra_hv: adding ivc2: rx_base=ffffff800a120000 tx_base = ffffff) [ 1.120218] tegra_hv: added ivc2 [ 1.121544] tegra_hv: adding ivc1: rx_base=ffffff800a110000 tx_base = ffffff) [ 1.125304] tegra_hv: added ivc1 [ 1.126594] tegra_hv: adding ivc0: rx_base=ffffff800a100000 tx_base = ffffff) [ 1.130449] tegra_hv: added ivc0 [ 1.131720] tegra_hv: adding ivc31: rx_base=ffffff800a230000 tx_base = fffff) [ 1.135659] tegra_hv: added ivc31 [ 1.137018] tegra_hv: adding ivc30: rx_base=ffffff800a220000 tx_base = fffff) [ 1.140944] tegra_hv: added ivc30 [ 1.142242] tegra_hv: adding ivc29: rx_base=ffffff800a210000 tx_base = fffff) [ 1.146106] tegra_hv: added ivc29 [ 1.147410] tegra_hv: adding ivc28: rx_base=ffffff800a200000 tx_base = fffff) [ 1.151290] tegra_hv: added ivc28 [ 1.152663] tegra_hv: adding ivc110: rx_base=ffffff8009f40000 tx_base = ffff) [ 1.156062] tegra_hv: added ivc110 [ 1.157278] tegra_hv: adding ivc237: rx_base=ffffff800ac50000 tx_base = ffff) [ 1.160665] tegra_hv: added ivc237 [ 1.161877] tegra_hv: adding ivc234: rx_base=ffffff800abc0000 tx_base = ffff) [ 1.164943] tegra_hv: added ivc234 [ 1.166053] tegra_hv: adding ivc231: rx_base=ffffff800ab30000 tx_base = ffff) [ 1.169122] tegra_hv: added ivc231 [ 1.170095] tegra_hv: adding ivc127: rx_base=ffffff800ab20000 tx_base = ffff) [ 1.173040] tegra_hv: added ivc127 [ 1.174111] tegra_hv: adding ivc126: rx_base=ffffff800aa90000 tx_base = ffff) [ 1.177049] tegra_hv: added ivc126 [ 1.178062] tegra_hv: adding ivc118: rx_base=ffffff800aa80000 tx_base = ffff) [ 1.181044] tegra_hv: added ivc118 [ 1.182040] tegra_hv: adding ivc107: rx_base=ffffff800aa70000 tx_base = ffff) [ 1.185163] tegra_hv: added ivc107 [ 1.186178] tegra_hv: adding ivc105: rx_base=ffffff800aa60000 tx_base = ffff) [ 1.189048] tegra_hv: added ivc105 [ 1.190098] tegra_hv: adding ivc104: rx_base=ffffff800aa50000 tx_base = ffff) [ 1.193063] tegra_hv: added ivc104 [ 1.194055] tegra_hv: adding ivc101: rx_base=ffffff800a9c0000 tx_base = ffff) [ 1.197184] tegra_hv: added ivc101 [ 1.198205] tegra_hv: adding ivc42: rx_base=ffffff800a9b0000 tx_base = fffff) [ 1.201150] tegra_hv: added ivc42 [ 1.202133] tegra_hv: adding ivc39: rx_base=ffffff800a920000 tx_base = fffff) [ 1.205083] tegra_hv: added ivc39 [ 1.206065] tegra_hv: adding ivc38: rx_base=ffffff800a890000 tx_base = fffff) [ 1.209133] tegra_hv: added ivc38 [ 1.210138] tegra_hv: adding ivc35: rx_base=ffffff800a800000 tx_base = fffff) [ 1.213027] tegra_hv: added ivc35 [ 1.213984] tegra_hv: adding ivc76: rx_base=ffffff800a0c0000 tx_base = fffff) [ 1.217210] tegra_hv: added ivc76 [ 1.218157] tegra_hv: added mempool ��g Update VM Starting pipe manager... ��0: ipa=7fffa00000 size=400000 peer=4 [ 1.220096] tegra_hv: added mempool 1: ipa=7fff200000 size=800000 peer=4 [ 1.222169] tegra_hv: added mempool 2: ipa=7fff1f0000 size=10000 peer=4 [ 1.224218] tegra_hv: added mempool 3: ipa=7ffec00000 size=400000 peer=3 [ 1.226174] tegra_hv: added mempool 5: ipa=7ffebc0000 size=40000 peer=5 [ 1.228062] tegra_hv: added mempool 6: ipa=7ffe200000 size=800000 peer=6 [ 1.230099] tegra_hv: added mempool 8: ipa=7ffda00000 size=800000 peer=6 [ 1.232043] tegra_hv: added mempool 9: ipa=7ffd200000 size=800000 peer=6 [ 1.233952] tegra_hv: added mempool 10: ipa=7ffd1c0000 size=40000 peer=7 [ 1.235839] tegra_hv: added mempool 11: ipa=7ffd0c0000 size=100000 peer=7 [ 1.237938] tegra_hv: added mempool 14: ipa=7ffc800000 size=800000 peer=6 [ 1.239828] tegra_hv: added mempool 15: ipa=7ffb800000 size=1000000 peer=6 [ 1.241984] tegra_hv: added mempool 47: ipa=7ffb7c0000 size=40000 peer=3 [ 1.243873] tegra_hv: added mempool 48: ipa=7ffae00000 size=800000 peer=6 [ 1.245817] tegra_hv: added mempool 49: ipa=7ffa600000 size=800000 peer=6 [ 1.247706] tegra_hv: added mempool 50: ipa=7ff9e00000 size=800000 peer=6 [ 1.249816] tegra_hv: added mempool 52: ipa=7ff9600000 size=800000 peer=6 [ 1.251756] tegra_hv: added mempool 53: ipa=7ff8e00000 size=800000 peer=6 [ 1.253727] tegra_hv: added mempool 54: ipa=7ff8600000 size=800000 peer=6 [ 1.255684] tegra_hv: added mempool 56: ipa=7ff7e00000 size=800000 peer=6 [ 1.257569] tegra_hv: added mempool 57: ipa=7ff7600000 size=800000 peer=6 [ 1.259488] tegra_hv: added mempool 60: ipa=7ff6600000 size=1000000 peer=6 [ 1.261525] tegra_hv: added mempool 70: ipa=7fb6600000 size=40000000 peer=0 [ 1.263602] tegra_hv: initialized [ 1.265696] NET: Registered protocol family 16 [ 1.270440] pstore: using zlib compression [ 1.273964] console [pstore-1] enabled [ 1.275004] pstore: Registered ramoops as persistent store backend [ 1.276736] ramoops: attached 0x200000@0xffd00000, ecc: 0/0 [ 1.279247] cpuidle: using governor menu [ 1.288557] bpmp: mail init ok [ 1.292764] arm-smmu 12000000.iommu: found 2 SMMUs [ 1.295326] arm-smmu 12000000.iommu: probing hardware configuration... [ 1.297145] arm-smmu 12000000.iommu: SMMUv2 with: [ 1.298545] arm-smmu 12000000.iommu: stage 1 translation [ 1.300062] arm-smmu 12000000.iommu: 23 context banks (0 stage-2 onl) [ 1.302013] arm-smmu 12000000.iommu: Supported page sizes: 0x00001000 [ 1.303804] arm-smmu 12000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 1.314322] vdso: 2 pages (1 code @ ffffff8008e36000, 1 data @ ffffff8009a24) [ 1.316430] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 1.321625] DMA: preallocated 256 KiB pool for atomic allocations [ 1.323924] Registering BPMP clocks... [ 1.325462] tegra_bpmp_clk_init: clock init ok (400 clks) [ 1.327384] tegra_bpmp_of_clk_init: EMC proxy not found. [ 1.329881] tegra_powergate_init: DONE [ 1.335027] Tegra reboot handler registered. [ 1.336489] DTS File Name: /dvs/git/dirty/git-master_modular/kernel/kernel-4s [ 1.342442] DTB Build time: May 20 2019 14:31:03 [ 1.361362] mc: mapped MMIO address: 0xffffff800a660000 -> 0x2c10000 [ 1.363332] mc: mapped MMIO address: 0xffffff800a680000 -> 0x2c20000 [ 1.365161] mc: mapped MMIO address: 0xffffff800a6a0000 -> 0x2c30000 [ 1.367195] mc: mapped MMIO address: 0xffffff800a6c0000 -> 0x2c40000 [ 1.369004] mc: mapped MMIO address: 0xffffff800a6e0000 -> 0x2c50000 [ 1.370860] mc: mapped MMIO address: 0xffffff800a700000 -> 0x2b80000 [ 1.372796] mc: mapped MMIO address: 0xffffff800a720000 -> 0x2b90000 [ 1.374715] mc: mapped MMIO address: 0xffffff800a740000 -> 0x2ba0000 [ 1.376479] mc: mapped MMIO address: 0xffffff800a760000 -> 0x2bb0000 [ 1.378356] mc: mapped MMIO address: 0xffffff800a780000 -> 0x1700000 [ 1.569992] mc: mapped MMIO address: 0xffffff800a7a0000 -> 0x1710000 [ 1.571950] mc: mapped MMIO address: 0xffffff800a7c0000 -> 0x1720000 [ 1.573787] mc: mapped MMIO address: 0xffffff800a7e000��Starting��0 -> 0x170 [ 1.575658] mc: mapped MMIO address: 0xffffff800ac70000 -> 0x1740000 [ 1.577493] mc: mapped MMIO address: 0xffffff800ac90000 -> 0x1750000 [ 1.579385] mc: mapped MMIO address: 0xffffff800acb0000 -> 0x1760000 [ 1.581354] mc: mapped MMIO address: 0xffffff800acd0000 -> 0x1770000 [ 1.583272] nv-tegra-mc 2c10000.mc: No mssnvlin�� Clock init... Starting dtree-nvhvnet comms and security are not enabled! Configuring Static IP on hvnet interface Starting virtualized QSPI driver ... Starting SE server driver ... Starting TIPC driver ... Starting CCPLEX SDL Starting driveupdate Starting NvGuard_Layer0_OTA ��# ��k node [ 1.584769] mc-err: mcerr ops are set to t19x [ 1.588171] tegra-reset 0.bpmp_reset: registered 189 resets. [ 1.591592] iommu: Adding device d000000.bpmp to group 0 [ 1.593261] bpmp d000000.bpmp: Found mempool with id 3 [ 1.594886] bpmp d000000.bpmp: ivm 0x0000007ffec00000 [ 1.596702] bpmp: ping status is 0 [ 1.598058] bpmp d000000.bpmp: firmware tag is ddf097f91d44db78012913d725ee3e [ 1.608959] bpmp d000000.bpmp: probe ok [ 1.618266] gpiochip_setup_dev: registered GPIOs 288 to 511 on device: gpioc) [ 1.629063] gpiochip_setup_dev: registered GPIOs 248 to 287 on device: gpioc) [ 1.633712] tegra186-aowake c370000.pmc: WAKE_AOWAKE_CTRL_0 = 3 [ 1.635393] tegra186-aowake c370000.pmc: WAKE_AOWAKE_CNTRL_24(PMU_INT) = 256 [ 1.639515] arm64_ras arm64_ras: None of the CPUs support RAS [ 1.641198] arm64_ras: probe of arm64_ras failed with error -22 [ 1.643039] carmel_ras carmel_ras: Deferring probe, arm64_ras hasnt been prot [ 1.647825] vdd_otp: 5000 mV [ 1.649077] vdd_dummy: 5000 mV [ 1.650764] vdd_otp_1v8: 1800 mV [ 1.652147] vdd_otp_3v3: 3300 mV [ 1.653445] vdd_otp_1v2: 1200 mV [ 1.669162] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 1.674172] max929x_i2c_client_init: called [ 1.677579] tegra-pmc c360000.pmc: create /sys/kernel/debug/PMC/boot-chain-te [ 1.679812] tegra-pmc: get_secure_pmc_setting: done secure_pmc=0 [ 1.681669] tegra-pmc: ### PMC reset source: TEGRA_POWER_ON_RESET [ 1.683416] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_L0 [ 1.685203] tegra-pmc: ### PMC reset status reg: 0x0 [ 1.686686] tegra-pmc: PMC Prod config success [ 1.689391] eventlib_kernel: keventlib is initialized, test id: 0 [ 1.691695] SCSI subsystem initialized [ 1.693074] usbcore: registered new interface driver usbfs [ 1.694672] usbcore: registered new interface driver hub [ 1.696356] usbcore: registered new device driver usb [ 1.698665] iommu: Adding device 3160000.i2c to group 1 [ 1.705148] iommu: Adding device c240000.i2c to group 1 [ 1.710669] iommu: Adding device 3180000.i2c to group 1 [ 1.715467] iommu: Adding device 3190000.i2c to group 1 [ 1.720114] iommu: Adding device 31b0000.i2c to group 1 [ 1.724676] iommu: Adding device 31c0000.i2c to group 1 [ 1.729172] iommu: Adding device c250000.i2c to group 1 [ 1.733787] iommu: Adding device 31e0000.i2c to group 1 [ 1.741718] max77620 4-003c: PMIC Version OTP:0x51 and ES:0x1 [ 1.745055] max77620 4-003c:��/dev/ivc87: No such file or directory # �� Backup battery charging support disabled [ 1.748100] max77620-sd0: supplied by regulator-dummy [ 1.750071] max77620-sd0: at 1000 mV [ 1.751916] max77620-sd1: supplied by regulator-dummy [ 1.753881] max77620-sd1: at 1800 mV [ 1.755808] max77620-sd2: supplied by regulator-dummy [ 1.757772] max77620-sd2: at 1800 mV [ 1.759690] max77620-sd3: supplied by regulator-dummy [ 1.761653] max77620-sd3: at 1800 mV [ 1.763603] max77620-sd4: supplied by regulator-dummy [ 1.765617] max77620-sd4: at 1100 mV [ 1.767551] max77620-ldo0: supplied by regulator-dummy [ 1.769576] max77620-ldo0: at 800 mV [ 1.771226] max77620-ldo1: supplied by regulator-dummy [ 1.773390] max77620-ldo1: at 2375 mV [ 1.775111] max77620-ldo2: supplied by regulator-dummy [ 1.777289] max77620-ldo2: at 3300 mV [ 1.778993] max77620-ldo3: supplied by regulator-dumm��main:��y [ �� CmdRes�� 1.781095] max77620-ldo3: at 3300 mV [ 1.782737] max77620-ldo4: supplied by regulator-dummy [ 1.784744] max77620-ldo4: at 1587 mV [ 1.786536] max77620-ldo5: supplied by regulator-dummy [ 1.788618] max77620-ldo5: at 3300 mV [ 1.790396] max77620-ldo6: supplied by regulator-dummy [ 1.792379] max77620-ldo6: at 3300 mV [ 1.794066] max77620-ldo7: supplied by regulator-dummy [ 1.796177] max77620-ldo7: at 1200 mV [ 1.797944] max77620-ldo8: supplied by regulator-dummy [ 1.800000] max77620-ldo8: at 1800 mV [ 1.801746] gpiochip_setup_dev: registered GPIOs 240 to 247 on device: gpioc) [ 2.011577] i2c i2c-4: deserialize_i2c ret -22 [ 2.012876] i2c i2c-4: --- message dump for debugging --- [ 2.014456] i2c i2c-4: addr 0x3c flags 0x0 len 2 data: [ 2.016015] i2c i2c-4: 0d [ 2.016832] i2c i2c-4: ef [ 2.017655] i2c i2c-4: [ 2.018476] max77620 4-003c: Failed to sync masks in d [ 2.020761] max77620 4-003c: max77620 probe successful [ 2.023068] media: Linux media interface: v0.10 [ 2.024500] Linux video capture interface: v2.00 [ 2.027938] pps_core: LinuxPPS API ver. 1 registered [ 2.029425] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giom> [ 2.032260] PTP clock support registered [ 2.038780] trusty trusty: trusty version: Built: 17:51:47 May 23 2019 [ 2.041085] trusty trusty: selected api version: 3 (requested 3) [ 2.044748] usb0-vbus: 5000 mV [ 2.045968] usb1-vbus: 5000 mV [ 2.047214] usb2-vbus: 5000 mV [ 2.050772] camchar: rtcpu character device driver loaded [ 2.053356] clocksource: Switched to clocksource arch_sys_counter [ 2.111248] VFS: Disk quotas dquot_6.6.0 [ 2.112575] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 2.114838] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 2.117212] iommu: Adding device 2600000.dma to group 1 [ 2.121388] tegra-carveouts tegra-carveouts: generic-0 :dma coherent mem dec4 [ 2.125395] tegra-carveouts tegra-carveouts: assigned reserved memory node gt [ 2.128467] nvmap_populate_ivm_carveout: IVM carveout IPA:0000007fb6600000, 1 [ 2.131812] tegra-carveouts tegra-carveouts: assigned reserved memory node c0 [ 2.134163] nvmap: nvmap_select_cache_ops() nvmap cache ops set to scf [ 2.136022] nvmap_page_pool_init: Total RAM pages: 7145537 [ 2.137736] nvmap_page_pool_init: nvmap page pool size: 893192 pages (3489 M) [ 2.139919] nvmap_background_zero_thread: PP zeroing thread starting. [ 2.140461] misc nvmap: created heap generic-0 base 0x00000000bfd00000 size ) [ 2.140555] misc nvmap: ivm000001 :dma coherent mem declare 0x0000007fb660004 [ 2.140629] misc nvmap: created heap ivm000001 base 0x0000007fb6600000 size ) [ 2.142135] tegra-gpcdma 2600000.dma: GPC DMA driver register 20 channels [ 2.152423] thermal thermal_zone0: Registering thermal zone thermal_zone0 fom [ 2.152486] thermal thermal_zone1: Registering thermal zone thermal_zone1 fom [ 2.152547] thermal thermal_zone2: Registering thermal zone thermal_zone2 fom [ 2.152749] thermal thermal_zone3: Registering thermal zone thermal_zone3 fom [ 2.152833] thermal thermal_zone4: Registering thermal zone thermal_zone4 fom [ 2.152912] thermal thermal_zone5: Registering thermal zone thermal_zone5 foa [ 2.154216] la/ptsa driver initialized. [ 2.154764] NET: Registered protocol family 2 [ 2.155566] TCP established hash table entries: 262144 (order: 9, 2097152 by) [ 2.156642] TCP bind hash table entries: 65536 (order: 9, 3670016 bytes) [ 2.158145] TCP: Hash tables configured (established 262144 bind 65536) [ 2.158281] UDP hash table entries: 16384 (order: 9, 2097152 bytes) [ 2.159052] UDP-Lite hash table entries: 16384 (order: 9, 2097152 bytes) [ 2.160150] NET: Registered protocol family 1 [ 2.160886] RPC: Registered named UNIX socket transport module. [ 2.160891] RPC: Registered udp transport module. [ 2.160894] RPC: Registered tcp transport module. [ 2.160898] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.161097] Unpacking initramfs... [ 2.180126] Freeing initrd memory: 4980K [ 2.182599] iommu: Adding device 13e10000.host1x to group 2 [ 2.195152] t194_init_regs: Host1x HW syncpt ram init disabled [ 2.198587] host1x 13e10000.host1x: initialized [ 2.201926] hw perfevents: failed to parse interrupt-affinity[6] for arm-pmu [ 2.203892] hw perfevents: /arm-pmu: failed to register PMU devices! [ 2.384470] armv8-pmu: probe of arm-pmu failed with error -22 [ 2.387339] audit: initializing netlink subsys (disabled) [ 2.389189] audit: type=2000 audit(2.364:1): state=initialized audit_enabled1 [ 2.389653] workingset: timestamp_bits=46 max_order=23 bucket_order=0 [ 2.396469] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.399328] ntfs: driver 2.1.32 [Flags: R/W]. [ 2.405741] Block layer SCSI generic (bsg) driver version 0.4 loaded (major ) [ 2.408060] io scheduler noop registered (default) [ 2.409608] io scheduler cfq registered [ 2.410681] io scheduler mq-deadline registered [ 2.411957] io scheduler kyber registered [ 2.427599] tegra-pwm c340000.pwm: PWM clk can sleep in ops [ 2.430497] tegra-pwm 32c0000.pwm: PWM clk can sleep in ops [ 2.432935] tegra-pwm 32f0000.pwm: PWM clk can sleep in ops [ 2.438075] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:e [ 2.440928] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=5 [ 2.447914] iommu: Adding device 14800000.isp to group 3 [ 2.452298] iommu: Adding device 13e10000.host1x:ctx0 to group 4 [ 2.454227] iommu_context_dev 13e10000.host1x:ctx0: initialized (streamid=56) [ 2.456938] iommu: Adding device 13e10000.host1x:ctx1 to group 5 [ 2.458853] iommu_context_dev 13e10000.host1x:ctx1: initialized (streamid=57) [ 2.461586] iommu: Adding device 13e10000.host1x:ctx2 to group 6 [ 2.463394] iommu_context_dev 13e10000.host1x:ctx2: initialized (streamid=58) [ 2.466190] iommu: Adding device 13e10000.host1x:ctx4 to group 7 [ 2.467984] iommu_context_dev 13e10000.host1x:ctx4: initialized (streamid=60) [ 2.475262] t194-nvcsi 15a00000.nvcsi: context isolation disabled due to no U [ 2.477753] t194-nvcsi 15a00000.nvcsi: initialized [ 2.480892] vhost-client 15340000.vic: Creating tegra-iommu group 1 [ 2.483211] iommu: Adding device 15340000.vic to group 8 [ 2.487927] vhost-client 15340000.vic: initialized [ 2.489506] vhost-client 15380000.nvjpg: Adding to tegra-iommu group 1 [ 2.491480] iommu: Adding device 15380000.nvjpg to group 8 [ 2.495466] vhost-client 15380000.nvjpg: initialized [ 2.497009] vhost-client 15480000.nvdec: Adding to tegra-iommu group 1 [ 2.499097] iommu: Adding device 15480000.nvdec to group 8 [ 2.505605] vhost-client 15480000.nvdec: initialized [ 2.507147] vhost-client 15140000.nvdec1: Adding to tegra-iommu group 1 [ 2.509185] iommu: Adding device 15140000.nvdec1 to group 8 [ 2.515396] vhost-client 15140000.nvdec1: initialized [ 2.516950] vhost-client 154c0000.nvenc: Adding to tegra-iommu group 1 [ 2.518991] iommu: Adding device 154c0000.nvenc to group 8 [ 2.522817] vhost-client 154c0000.nvenc: initialized [ 2.524310] vhost-client 15a80000.nvenc1: Adding to tegra-iommu group 1 [ 2.526386] iommu: Adding device 15a80000.nvenc1 to group 8 [ 2.530281] vhost-client 15a80000.nvenc1: initialized [ 2.536831] scare-pigeon 13e10000.host1x:vi-thi@15f00000: context isolation U [ 2.539646] scare-pigeon 13e10000.host1x:vi-thi@15f00000: initialized [ 2.541701] iommu: Adding device 14b00000.isp-thi to group 3 [ 2.543671] scare-pigeon 14b00000.isp-thi: initialized [ 2.546226] iommu: Adding device 16000000.pva0 to group 9 [ 2.554337] pva 16000000.pva0: initialized [ 2.556747] iommu: Adding device 16800000.pva1 to group 10 [ 2.564728] pva 16800000.pva1: initialized [ 2.566971] nvdla 15880000.nvdla0: Adding to tegra-iommu group 1 [ 2.568884] iommu: Adding device 15880000.nvdla0 to group 8 [ 2.575871] nvdla 15880000.nvdla0: initialized [ 2.578071] nvdla 158c0000.nvdla1: Adding to tegra-iommu group 1 [ 2.579968] iommu: Adding device 158c0000.nvdla1 to group 8 [ 2.586931] nvdla 158c0000.nvdla1: initialized [ 2.589894] tegradccommon 15200000.dc_common: host1x channel mapped [ 2.591678] tegradccommon 15200000.dc_common: dc_common syncpt # 1 allocated [ 2.593440] scrncapt: init (heads:4 wins:6 planes:4) [ 2.595162] tegradccommon 15200000.dc_common: dma mapping done [ 2.595758] tegra-fuse-burn 3820000.efuse:efuse-burn: Fuse burn driver initid [ 2.596487] kfuse 3830000.kfuse: initialized [ 2.600860] tegradc 15200000.nvdisplay: disp0 connected to head0->/host1x/sor [ 2.603917] generic_infoframe_type: 0x87 [ 2.604269] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 2.606130] iommu: Adding device c280000.serial to group 1 [ 2.606476] console [ttyS0] disabled [ .788751] tegradc 15200000.nvdisplay: DT parsed successfully [ 2.788782] c280000.serial: ttyS0 at MMIO 0xc280000 (irq = 95, base_baud = 2a [ 2.792874] tegradc 15200000.nvdisplay: Display dc.ffffff800bee0000 register0 [ 2.792874] tegradc 15200000.nvdisplay: Display dc.ffffff800bee0000 register0 [ 2.798909] tegra_nvdisp_bandwidth_register_max_config: max config iso bw = s [ 2.798909] tegra_nvdisp_bandwidth_register_max_config: max config iso bw = s [ 2.798918] tegra_nvdisp_bandwidth_register_max_config: max config EMC floorz [ 2.798918] tegra_nvdisp_bandwidth_register_max_config: max config EMC floorz [ 2.798925] tegra_nvdisp_bandwidth_register_max_config: max config hubclk = z [ 2.798925] tegra_nvdisp_bandwidth_register_max_config: max config hubclk = z [ 2.799558] tegradc 15200000.nvdisplay: vblank syncpt # 8 for dc 0 [ 2.799558] tegradc 15200000.nvdisplay: vblank syncpt # 8 for dc 0 [ 2.799564] tegradc 15200000.nvdisplay: vpulse3 syncpt # 9 for dc 0 [ 2.799564] tegradc 15200000.nvdisplay: vpulse3 syncpt # 9 for dc 0 [ 2.803418] tegradc 15200000.nvdisplay: hdmi: board prod-setting covers part! [ 2.803418] tegradc 15200000.nvdisplay: hdmi: board prod-setting covers part! [ 2.809600] tegradc 15200000.nvdisplay: probed [ 2.809600] tegradc 15200000.nvdisplay: probed [ 2.834016] console [ttyS0] enabled [ 2.834016] console [ttyS0] enabled [ 2.834023] tegradc 15200000.nvdisplay: fb registered [ 2.834023] tegradc 15200000.nvdisplay: fb registered [ 2.834341] gpio tegra-gpio wake60 for gpio=96(M:0) [ 2.834341] gpio tegra-gpio wake60 for gpio=96(M:0) [ 2.834701] tegradc 15210000.nvdisplay: disp1 connected to head1->/host1x/so1 [ 2.834701] tegradc 15210000.nvdisplay: disp1 connected to head1->/host1x/so1 [ 2.834731] generic_infoframe_type: 0x87 [ 2.834731] generic_infoframe_type: 0x87 [ 2.834767] tegradc 15210000.nvdisplay: DT parsed successfully [ 2.834767] tegradc 15210000.nvdisplay: DT parsed successfully [ 2.834785] tegradc 15210000.nvdisplay: Display dc.ffffff800bfd0000 register1 [ 2.834785] tegradc 15210000.nvdisplay: Display dc.ffffff800bfd0000 register1 [ 2.835029] tegradc 15210000.nvdisplay: vblank syncpt # 11 for dc 1 [ 2.835029] tegradc 15210000.nvdisplay: vblank syncpt # 11 for dc 1 [ 2.835036] tegradc 15210000.nvdisplay: vpulse3 syncpt # 12 for dc 1 [ 2.835036] tegradc 15210000.nvdisplay: vpulse3 syncpt # 12 for dc 1 [ 2.838322] tegradc 15210000.nvdisplay: hdmi: board prod-setting covers part! [ 2.838322] tegradc 15210000.nvdisplay: hdmi: board prod-setting covers part! [ 2.842083] tegradc 15210000.nvdisplay: probed [ 2.842083] tegradc 15210000.nvdisplay: probed [ 3.053880] bootconsole [uart8250] disabled [ 3.053880] bootconsole [uart8250] disabled [ 3.056674] tegradc 15210000.nvdisplay: fb registered [ 3.056972] gpio tegra-gpio wake63 for gpio=97(M:1) [ 3.057445] tegradc 15220000.nvdisplay: disp2 connected to head2->/host1x/so2 [ 3.057474] generic_infoframe_type: 0x87 [ 3.057512] tegradc 15220000.nvdisplay: DT parsed successfully [ 3.057531] tegradc 15220000.nvdisplay: Display dc.ffffff800ca10000 register2 [ 3.057800] tegradc 15220000.nvdisplay: vblank syncpt # 13 for dc 2 [ 3.057805] tegradc 15220000.nvdisplay: vpulse3 syncpt # 14 for dc 2 [ 3.060887] tegradc 15220000.nvdisplay: hdmi: board prod-setting covers part! [ 3.064427] tegradc 15220000.nvdisplay: probed [ 3.079483] extcon-disp-state external-connection:disp-state: cable 40 state1 [ 3.079488] Extcon HDMI: HPD enabled [ 3.079498] tegradc 15200000.nvdisplay: hdmi: plugged [ 3.080440] iommu: Adding device 3110000.serial to group 1 [ 3.082176] 3110000.serial: ttyTHS1 at MMIO 0x3110000 (irq = 94, base_baud =T [ 3.095963] tegradc 15220000.nvdisplay: fb registered [ 3.099894] gpio tegra-gpio wake71 for gpio=98(M:2) [ 3.100844] tegradc 15230000.nvdisplay: disp3 connected to head3->/host1x/so3 [ 3.108524] generic_infoframe_type: 0x87 [ 3.110634] tegradc 15230000.nvdisplay: DT parsed successfully [ 3.112684] tegradc 15230000.nvdisplay: Display dc.ffffff800cbd0000 register3 [ 3.115917] tegradc 15230000.nvdisplay: vblank syncpt # 15 for dc 3 [ 3.118246] tegradc 15230000.nvdisplay: vpulse3 syncpt # 16 for dc 3 [ 3.123759] tegradc 15230000.nvdisplay: hdmi: board prod-setting covers part! [ 3.127888] tegra_hv_vblk tegra_virt_storage0: allocate drvdata buffer [ 3.130363] tegradc 15230000.nvdisplay: probed [ 3.132115] tegradc 15230000.nvdisplay: fb registered [ 3.132752] vblk: send_config wait for ivc channel reset [ 3.136263] gpio tegra-gpio wake66 for gpio=99(M:3) [ 3.137370] tegra_hv_vblk tegra_virt_storage0: send config cmd to ivc #127 [ 3.141637] tegra_hv_vblk tegra_virt_storage1: allocate drvdata buffer [ 3.141808] tegra_hv_vblk tegra_virt_storage0: get config data from ivc #127 [ 3.145134] Primary GPT is invalid, using alternate GPT. [ 3.145149] vblkdev0: p1 [ 3.150275] vblk: send_config wait for ivc channel reset [ 3.152235] tegra_hv_vblk tegra_virt_storage1: send config cmd to ivc #237 [ 3.154890] tegra_hv_vblk tegra_virt_storage2: allocate drvdata buffer [ 3.154959] tegra_hv_vblk tegra_virt_storage1: get config data from ivc #237 [ 3.160400] vblk: send_config wait for ivc channel reset [ 3.162427] tegra_hv_vblk tegra_virt_storage2: send config cmd to ivc #42 [ 3.164929] tegra_hv_vblk tegra_virt_storage3: allocate drvdata buffer [ 3.164983] tegra_hv_vblk tegra_virt_storage2: get config data from ivc #42 [ 3.170441] vblk: send_config wait for ivc channel reset [ 3.172403] tegra_hv_vblk tegra_virt_storage3: send config cmd to ivc #234 [ 3.175000] tegra_hv_vblk tegra_virt_storage4: allocate drvdata buffer [ 3.175075] tegra_hv_vblk tegra_virt_storage3: get config data from ivc #234 [ 3.175209] tegra_hv_vblk tegra_virt_storage3: IVC frames 1 less than possib! [ 3.183712] vblk: send_config wait for ivc channel reset [ 3.185775] tegra_hv_vblk tegra_virt_storage4: send config cmd to ivc #126 [ 3.188300] tegra_profiler: version: 1.134, samples/io: 47/26 [ 3.188343] tegra_hv_vblk tegra_virt_storage4:get config data from ivc #126 [ 3.188483] tegra_hv_vblk tegra_virt_storage4: Setting Max requests to 16, c! [ 3.188488] tegra_hv_vblk tegra_virt_storage4: IVC frames 1 less than possib! [ 3.365024] tegra_profiler: auth: init [ 3.368330] libphy: Fixed MDIO Bus: probed [ 3.370063] tun: Universal TUN/TAP device driver, 1.6 [ 3.372126] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 3.374283] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.376417] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 3.378972] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.381212] eqos 2490000.ether_qos: Creating tegra-iommu group 2 [ 3.383850] iommu: Adding device 2490000.ether_qos to group 11 [ 3.386772] eqos 2490000.ether_qos: no PHY interrupt found [ 3.388737] eqos 2490000.ether_qos: no PHY reset gpio found [ 3.396426] eqos 2490000.ether_qos: Setting local MAC: 0 4 4b cb ce dc [ 3.401527] PPP generic driver version 2.4.2 [ 3.403240] PPP BSD Compression module registered [ 3.404964] PPP Deflate Compression module registered [ 3.406833] PPP MPPE Compression module registered [ 3.408626] usbcore: registered new interface driver r8152 [ 3.410678] usbcore: registered new interface driver asix [ 3.412636] usbcore: registered new interface driver ax88179_178a [ 3.414899] usbcore: registered new interface driver cdc_ether [ 3.416991] usbcore: registered new interface driver net1080 [ 3.419104] usbcore: registered new interface driver cdc_subset [ 3.421199] usbcore: registered new interface driver zaurus [ 3.423259] usbcore: registered new interface driver cdc_ncm [ 3.425479] tegra_hv_net tegra_hv_net@0: Reserved IVC channel #233 - frame_s6 [ 3.428239] tegra_hv_net tegra_hv_net@0: No valid mac-address found, using fs [ 3.432151] tegra_hv_net tegra_hv_net@0: ready [ 3.434434] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.436758] ehci-pci: EHCI PCI platform driver [ 3.438437] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.440668] ohci-pci: OHCI PCI platform driver [ 3.442355] ohci-platform: OHCI generic platform driver [ 3.445464] iommu: Adding device 3610000.xhci to group 12 [ 3.452526] tegra-xusb 3610000.xhci: No USB port has OTG_CAP [ 3.458757] usbcore: registered new interface driver uas [ 3.460733] tegra-xusb 3610000.xhci: Firmware timestamp: 2018-03-29 14:24:42e [ 3.461485] usbcore: registered new interface driver usb-storage [ 3.463046] iommu: Adding device 3550000.xudc to group 13 [ 3.464621] Could not get extcon-dev /xudc@3550000:vbus(0) [ 3.465125] mousedev: PS/2 mouse device common for all mice [ 3.465173] usbcore: registered new interface driver xpad [ 3.467006] i2c i2c-4: deserialize_i2c ret -22 [ 3.467011] i2c i2c-4: --- message dump for debugging --- [ 3.467015] i2c i2c-4: addr 0x3c flags 0x0 len 2 data: [ 3.467019] i2c i2c-4: 0d [ 3.467022] i2c i2c-4: e7 [ 3.467025] i2c i2c-4: [ 3.467032] max77620 4-003c: Failed to sync masks in d [ 3.467503] i2c i2c-4: deserialize_i2c ret -22 [ 3.467506] i2c i2c-4: --- message dump for debugging --- [ 3.467511] i2c i2c-4: addr 0x68 flags 0x0 len 2 data: [ 3.467515] i2c i2c-4: 02 [ 3.467519] i2c i2c-4: 03 [ 3.467521] i2c i2c-4: [ 3.467526] max77686-rtc max77620-rtc: _egmap_bulk_write() failed, e -22 [ 3.467530] max77686-rtc max77620-rtc: Fail to write controlm reg(-22) [ 3.467533] max77686-rtc max77620-rtc: Failed to initialize RTC reg:-22 [ 3.467986] i2c i2c-4: deserialize_i2c ret -22 [ 3.467990] i2c i2c-4: --- message dump for debugging --- [ 3.467994] i2c i2c-4: addr 0x3c flags 0x0 len 2 data: [ 3.467997] i2c i2c-4: 0d [ 3.468000] i2c i2c-4: ef [ 3.468003] i2c i2c-4: [ 3.468008] max77620 4-003c: Failed to sync masks in d [ 3.468716] i2c i2c-4: deserialize_i2c ret -22 [ 3.468719] i2c i2c-4: --- message dump for debugging --- [ 3.468723] i2c i2c-4: addr 0x3c flags 0x0 len 2 data: [ 3.468726] i2c i2c-4: 0d [ 3.468732] i2c i2c-4: ef [ 3.468734] i2c i2c-4: [ 3.468738] max77620 4-003c: Failed to sync masks in d [ 3.469250] max77686-rtc: probe of max77620-rtc failed with error -22 [ 3.469547] i2c /dev entries driver [ 3.471015] IR NEC protocol handler initialized [ 3.471025] IR RC5(x/sz) protocol handler initialized [ 3.471032] IR RC6 protocol handler initialized [ 3.471038] IR JVC protocol handler initialized [ 3.471044] IR Sony protocol handler initialized [ 3.471049] IR SANYO protocol handler initialized [ 3.471055] IR Sharp protocol handler initialized [ 3.471061] IR MCE Keyboard/mouse protocol handler initialized [ 3.471067] IR XMP protocol handler initialized [ 3.471563] max77620-power max20024-power: Event recorder REG_NVERC : 0x40 [ 3.473702] tegra-bpmp-thermal d000000.bpmp:bpmpthermal: zone 0 not supported [ 3.474103] tegra-bpmp-thermal d000000.bpmp:bpmpthermal: zone 2 not supported [ 3.477692] device-mapper: uevent: version 1.0.3 [ 3.478124] device-mapper: ioctl: 4.37.0-ioctl (2017-09-20) initialised: dm-m [ 3.478935] sdhci: Secure Digital Host Controller Interface driver [ 3.478954] sdhci: Copyright(c) Pierre Ossman [ 3.478961] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.479725] iommu: Adding device 3400000.sdhci to group 14 [ 3.480002] sdhci-tegra 3400000.sdhci: runtime pm disabled [ 3.480004] hidraw: raw HID events driver (C) Jiri Kosina [ 3.480731] usbcore: registered new interface driver usbhid [ 3.480734] usbhid: USB HID core driver [ 3.481476] iommu: Adding device bc00000.rtcpu to group 15 [ 3.483271] sdhci-tegra 3400000.sdhci: Client registration for eMC Successful [ 3.483513] tegra186-cam-rtcpu bc00000.rtcpu: deferring, 14800000.isp is notd [ 3.485011] iommu: Adding device c1a0000.aon to group 16 [ 3.487809] tegra_aon c1a0000.aon: tegra aon driver probe OK [ 3.488469] tegra186-aondbg aondbg: aondbg driver probe() OK [ 3.489840] denver_knobs_init:MTS_VERSION:45309758 [ 3.490464] t19x_cache tegra-cache: probed [ 3.491562] misc nvmap: cvsram :dma coherent mem declare 0x0000000050000000,8 [ 3.491569] misc nvmap: created heap cvsram base 0x0000000050000000 size (30) [ 3.493109] trusty-irq trusty:irq: trusty_irq_create_irq_mappng failed (-75) [ 3.493114] trusty-irq trusty:irq: failed to initialize irq 449, irq will bed [ 3.494403] trusty-virtio trusty:virtio: initializing [ 3.494847] trusty_ipc virtio0: vring0: va(pa) ffffffc711838000(0) qsz 32 n1 [ 3.494889] trusty_ipc virtio0: vring1: va(pa) ffffffc71183a000(0) qsz 32 n2 [ 3.496164] trusty-virtio trusty:virtio: initializing done [ 3.496370] trusty_ipc virtio0: is online [ 3.498007] tegra_hv_pm_ctl tegra_hv_pm_ctl: tegra_hv_pm_ctl_probe: Probed [ 3.511377] u32 classifier [ 3.511386] Actions configured [ 3.511482] Initializing XFRM netlink socket [ 3.512200] NET: Registered protocol family 10 [ 3.513376] Segment Routing with IPv6 [ 3.513420] NET: Registered protocol family 17 [ 3.513444] NET: Registered protocol family 15 [ 3.513528] bridge: filtering via arp/ip/ip6tables is no longer available by. [ 3.513553] 9pnet: Installing 9P2000 support [ 3.513580] Key type dns_resolver registered [ 3.515963] registered taskstats version 1 [ 3.516579] iommu: Adding device 14180000.pcie to group 17 [ 3.516993] tegra-pcie-dw 14180000.pcie: Setting init speed to max speed [ 3.519413] OF: PCI: host bridge /pcie@14180000 ranges: [ 3.519426] OF: PCI: IO 0x38100000..0x381fffff -> 0x38100000 [ 3.519434] OF: PCI: MEM 0x38200000..0x39ffffff -> 0x38200000 [ 3.519438] OF: PCI: MEM 0x1800000000..0x1bffffffff -> 0x1800000000 [ 3.529363] mmc0: SDHCI controller on 3400000.sdhci [3400000.sdhci] using ADt [ 3.572957] mmc0: Switching to 1.8V signalling voltage failed [ 3.581419] mmc0: new DDR MMC card at address 0001 [ 3.581899] mmcblk0: mmc0:0001 008G30 7.28 GiB [ 3.582110] mmcblk0boot0: mmc0:0001 008G30 partition 1 8.00 MiB [ 3.582346] mmcblk0boot1: mmc0:0001 008G30 partition 2 8.00 MiB [ 3.582536] mmcblk0rpmb: mmc0:0001 008G30 partition 3 4.00 MiB [ 3.625361] tegra-pcie-dw 14180000.pcie: link is up [ 3.625605] tegra-pcie-dw 14180000.pcie: PCI host bridge to bus 0000:00 [ 3.625615] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.625622] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus add) [ 3.625644] pci_bus 0000:00: root bus resource [mem 0x38200000-0x39ffffff] [ 3.625648] pci_bus 0000:00: root bus resource [mem 0x1800000000-0x1bfffffff] [ 3.626911] pci 0000:01:00.0: enabling Extended Tags [ 3.630253] pci 0000:01:00.1: enabling Extended Tags [ 3.632029] pci 0000:01:00.0: bridge configuration invalid ([bus 00-00]), reg [ 3.633572] pci 0000:02:00.0: enabling Extended Tags [ 3.636535] pci 0000:02:01.0: enabling Extended Tags [ 3.639146] pci 0000:02:00.0: bridge configuration invalid ([bus 00-00]), reg [ 3.639285] pci 0000:02:01.0: bridge configuration invalid ([bus 00-00]), reg [ 3.641804] pci 0000:04:00.0: enabling Extended Tags [ 3.646230] pci 0000:00:00.0: BAR 15: assigned [mem 0x1800000000-0x1805fffff] [ 3.646257] pci 0000:00:000: BAR 14: assigned [mem 0x38200000-0x389fffff] [ 3.646263] pci 0000:00:00.0: BAR 13: assigned [io 0x1000-0x2fff] [ 3.646288] pci 0000:01:00.1: BAR 4: assigned [mem 0x1800000000-0x1803ffffff] [ 3.646444] pci 0000:01:00.1: BAR 0: assigned [mem 0x1804000000-0x18043fffff] [ 3.646682] pci 0000:01:00.1: BAR 2: assigned [mem 0x1804400000-0x18047fffff] [ 3.646878] pci 0000:01:00.0: BAR 14: assigned [mem 0x38200000-0x389fffff] [ 3.646883] pci 0000:01:00.0: BAR 15: assigned [mem 0x1804800000-0x1804bffff] [ 3.646888] pci 0000:01:00.0: BAR 13: assigned [io 0x1000-0x2fff] [ 3.646895] pci 0000:02:01.0: BAR 14: assigned [mem 0x38200000-0x387fffff] [ 3.646900] pci 0000:02:00.0: BAR 14: assigned [mem 0x38800000-0x389fffff] [ 3.646925] pci 0000:02:00.0: BAR 15: assigned [mem 0x1804800000-0x18049ffff] [ 3.646930] pci 0000:02:01.0: BAR 15: assigned [mem 0x1804a00000-0x1804bffff] [ 3.646935] pci 0000:02:00.0: BAR 13: assigned [io 0x1000-0x1fff] [ 3.646959] pci 0000:02:01.0: BAR 13: assigned [io 0x2000-0x2fff] [ 3.646965] pci 0000:02:00.0: PCI bridge to [bus 03] [ 3.646986] pci 0000:02:00.0: bridge window [io 0x1000-0x1fff] [ 3.647149] pci 0000:02:00.0: bridge window [mem 0x38800000-0x389fffff] [ 3.647345] pci 0000:02:00.0: bridge window [mem 0x1804800000-0x18049fffff] [ 3.647658] pci 0000:04:00.0: BAR 4: assigned [mem 0x38400000-0x387fffff 64b] [ 3.647776] pci 0000:04:00.0: BAR 6: assigned [mem 0x38200000-0x3823ffff pre] [ 3.647800] pci 0000:04:00.0: BAR 0: assigned [mem 0x38240000-0x3824ffff 64b] [ 3.647950] pci 0000:04:00.0: BAR 2: assigned [mem 0x38250000-0x38250fff 64b] [ 3.648084] pci 0000:02:01.0: PCI bridge to [bus 04] [ 3.648109] pci 0000:02:01.0: bridge window [io 0x2000-0x2fff] [ 3.648267] pci 0000:02:01.0: bridge window [mem 0x38200000-0x387fffff] [ 3.648464] pci 0000:02:01.0: bridge window [mem 0x1804a00000-0x1804bfffff] [ 3.648776] pci 0000:01:00.0: PCI bridge to [bus 02-04] [ 3.648800] pci 0000:01:00.0: bridge window [io 0x1000-0x2fff] [ 3.648884] pci 0000:01:00.0: bridge window [mem 0x38200000-0x389fffff] [ 3.649211] pci 0000:01:00.0: bridge window [mem 0x1804800000-0x1804bfffff] [ 3.649538] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 3.649563] pci 0000:00:00.0: bridge window [io 0x1000-0x2fff] [ 3.649569] pci 0000:00:00.0: bridge window [mem 0x38200000-0x389fffff] [ 3.649574] pci 0000:00:00.0: bridge window [mem 0x1800000000-0x1805ffffff] [ 3.649614] pci 0000:00:00.0: Max Payload Size set to 128/ 256 (was 256), 2 [ 3.649708] pci 0000:01:00.0: Max Payload ize set to 128/ 512 (was 128), M8 [ 3.649802] pci 0000:02:00.0: Max Payload Size set to 128/ 512 (was 128), 8 [ 3.649894] pci 0000:02:01.0: Max Payload Size set to 128/ 512 (was 128), 8 [ 3.650000] pci 0000:04:00.0: Max Payload Size set to 128/ 512 (was 128), 2 [ 3.650086] pci 0000:01:00.1: Max Payload Size set to 128/ 512 (was 128), 2 [ 3.650375] iommu: Adding device 0000:00:00.0 to group 17 [ 3.650907] pcieport 0000:00:00.0: Signaling PME with IRQ 78 [ 3.651256] pcieport 0000:00:00.0: AER enabled with IRQ 78 [ 3.651745] iommu: Adding device 0000:01:00.0 to group 17 [ 3.651886] pcieport 0000:01:00.0: enabling device (0000 -> 0003) [ 3.654598] iommu: Adding device 0000:02:00.0 to group 17 [ 3.654772] pcieport 0000:02:00.0: enabling device (0000 -> 0003) [ 3.657765] iommu: Adding device 0000:02:01.0 to group 17 [ 3.657903] pcieport 0000:02:01.0: enabling device (0000 -> 0003) [ 3.661205] iommu: Adding device 14100000.pcie to group 18 [ 3.661640] tegra-pcie-dw 14100000.pcie: Setting init speed to max speed [ 3.663956] OF: PCI: host bridge /pcie@14100000 ranges: [ 3.663969] OF: PCI: IO 0x30100000..0x301fffff -> 0x30100000 [ 3.663977] OF: PCI: MEM 0x30200000..0x31ffffff -> 0x30200000 [ 3.663982] OF: PCI: MEM 0x1200000000..0x123fffffff -> 0x1200000000 [ 3.773397] tegra-pcie-dw 14100000.pcie: link is up [ 3.773603] tegra-pcie-dw 14100000.pcie: PCI host bridge to bus 0001:00 [ 3.773612] pci_bus 0001:00: root bus resource [bus 00-ff] [ 3.773619] pci_bus 0001:00: root bus resource [io 0x100000-0x1fffff] (bus ) [ 3.773623] pci_bus 0001:00: root bus resource [mem 0x30200000-0x31ffffff] [ 3.773627] pci_bus 0001:00: root bus resource [mem 0x1200000000-0x123ffffff] [ 3.776628] pci 0001:00:00.0: BAR 15: assigned [mem 0x1200000000-0x1217fffff] [ 3.776635] pci 0001:00:00.0: BAR 14: assigned [mem 0x31000000-0x31ffffff] [ 3.776640] pci 0001:00:00.0: BAR 13: assigned [io 0x100000-0x100fff] [ 3.776648] pci 0001:01:00.0: BAR 1: assigned [mem 0x1200000000-0x120fffffff] [ 3.776692] pci 0001:01:00.0: BAR 3: assigned [mem 0x1210000000-0x1211ffffff] [ 3.776735] pci 0001:01:00.0: BAR 0: assigned [mem 0x31000000-0x31ffffff] [ 3.776751] pci 0001:01:00.0: BAR 5: assigned [io 0x100000-0x10007f] [ 3.776767] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 3.776774] pci 0001:00:00.0: bridge window [io 0x100000-0x100fff] [ 3.776780] pci 0001:00:00.0: bridge window [mem 0x31000000-0x31ffffff] [ 3.776786] pci 0001:00:00.0: bridge window [mem 0x1200000000-0x1217fffff ] [ 3.776811] pci 0001:00:00.0: Max Payload Size set to 256/ 256 (was 256), 2 [ 3.776843] pci 0001:01:00.0: Max Payload Size set to 256/ 256 (was 128), 2 [ 3.777092] iommu: Adding device 0001:00:00.0 to group 18 [ 3.777544] pcieport 0001:00:00.0: Signaling PME with IRQ 80 [ 3.777784] pcieport 0001:00:00.0: AER enabled with IRQ 80 [ 3.778562] iommu: Adding device 14160000.pcie to group 19 [ 3.778961] tegra-pcie-dw 14160000.pcie: Setting init speed to max speed [ 3.781408] OF: PCI: host bridge /pcie@14160000 ranges: [ 3.781422] OF: PCI: IO 0x36100000..0x361fffff -> 0x36100000 [ 3.781432] OF: PCI: MEM 0x36200000..0x37ffffff -> 0x36200000 [ 3.781437] OF: PCI: MEM 0x1400000000..0x17ffffffff -> 0x1400000000 [ 3.889445] tegra-pcie-dw 14160000.pcie: link is up [ 3.889669] tegra-pcie-dw 14160000.pcie: PCI host bridge to bus 0004:00 [ 3.889678] pci_bus 0004:00: root bus resource [bus 00-ff] [ 3.889685] pci_bus 0004:00: root bus resource [io 0x200000-0x2fffff] (bus ) [ 3.889705] pci_bus 0004:00: root bus resource [mem 0x36200000-0x37ffffff] [ 3.889710] pci_bus 0004:00: root bus resource [mem 0x1400000000-0x17fffffff] [ 3.890601] pci 0004:01:00.0: enabling Extended Tags [ 3.892315] pci 0004:00:00.0: BAR 14: assigned [mem 0x36200000-0x367fffff] [ 3.892342] pci 0004:01:00.0: BAR 4: assigned [mem 0x36400000-0x367fffff 64b] [ 3.892404] pci 0004:01:00.0: BAR 6: assigned [mem 0x36200000-0x3623ffff pre] [ 3.892411] pci 0004:01:00.0: BAR 0: assigned [mem 0x36240000-0x3624ffff 64b] [ 3.892478] pci 0004:01:00.0: BAR 2: assigned [mem 0x36250000-0x36250fff 64b] [ 3.892538] pci 0004:00:00.0: PCI bridge to [bus 01-ff] [ 3.892545] pci 0004:00:00.0: bridge window [mem 0x36200000-0x367fffff] [ 3.892577] pci 0004:00:00.0: Max Payload Size set to 256/ 256 (was 256), 2 [ 3.892610] pci 0004:01:00.0: Max Payload Size set to 256/ 512 (was 128), 2 [ 3.892821] iommu: Adding device 0004:00:00.0 to group 19 [ 3.893263] pcieport 0004:00:00.0: Signaling PME with IRQ 82 [ 3.893675] pcieport 0004:00:00.0: AER enabled with IRQ 82 [ 3.902910] carmel_ras carmel_ras: Deferring probe, arm64_ras hasnt been prot [ 3.906440] tegra194-isp5 14800000.isp: initialized [ 3.917284] tegra194-vi5 15c10000.vi: context isolation disabled due to no IU [ 3.917521] tegra194-vi5 15c10000.vi: initialized [ 3.925442] tegra-xudc 3550000.xudc: device count: 1 [ 3.926637] tegra-xudc 3550000.xudc: vbus state: 0 [ 3.927717] tegra186-cam-rtcpu bc00000.rtcpu: Trace buffer configured at IOV0 [ 3.928139] tegra-xudc 355000.xudc: entering ELPG [ 3.928879] tegra-xudc 3550000.xudc: entering ELPG done [ 3.935976] tegra-ivc-bus bc00000.rtcpu:ivc-bus: region 0: iova=0xbfec0000-02 [ 3.936098] tegra-ivc-bus bc00000.rtcpu:ivc-bus:echo@0: echo: ver=0 grp=1 RX0 [ 3.936414] tegra-ivc-bus bc00000.rtcpu:ivc-bus:dbg@1: dbg: ver=0 grp=1 RX[10 [ 3.936620] tegra-ivc-bus bc00000.rtcpu:ivc-bus:dbg@2: dbg: ver=0 grp=1 RX[10 [ 3.937240] tegra-ivc-bus bc00000.rtcpu:ivc-bus:ivccontrol@3: ivccontrol: ve0 [ 3.937441] tegra-ivc-bus bc00000.rtcpu:ivc-bus:ivccapture@4: ivccapture: ve0 [ 3.938247] tegra186-cam-rtcpu bc00000.rtcpu: using cam RTCPU IRQ (110) [ 3.938253] tegra186-cam-rtcpu bc00000.rtcpu: tegra_camrtc_mon_create is sucl [ 3.940142] tegra186-cam-rtcpu bc00000.rtcpu: firmware version cpu=rce cmd=66 [ 3.940253] carmel_ras carmel_ras: Deferring probe, arm64_ras hasnt been prot [ 3.941504] hctosys: unable to open rtc device (rtc1) [ 3.942961] hvc_sysfs: log is available [ 3.942964] hvc_sysfs: pct is unavailable [ 3.948634] usb0-vbus: disabling [ 3.948646] usb1-vbus: disabling [ 3.948649] usb2-vbus: disabling [ 4.972297] tegra-xusb 3610000.xhci: xHCI Host Controller [ 4.974141] tegra-xusb 3610000.xhci: new USB bus registered, assigned bus nu1 [ 4.977680] tegra-xusb 3610000.xhci: hcc params 0x0184ff25 hci version 0x1100 [ 4.980969] tegra-xusb 3610000.xhci: irq 497, io mem 0x03610000 [ 4.983147] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.985151] Freeing unused kernel memory: 7168K [ 4.986846] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber1 [ 4.989122] usb usb1: Product: xHCI Host Controller [ 4.990734] usb usb1: Manufacturer: Linux 4.14.102-rt53-tegra xhci-hcd [ 4.990738] usb usb1: SerialNumber: 3610000.xhci [ 4.991268] hub 1-0:1.0: USB hub found [ 4.991300] hub 1-0:1.0: 4 ports detected [ 4.991752] carmel_ras carmel_ras: Deferring probe, arm64_ras hasnt been prot [ 5.005421] tegra-xusb 3610000.xhci: xHCI Host Controller [ 5.007294] tegra-xusb 3610000.xhci: new USB bus registered, assigned bus nu2 [ 5.009877] tegra-xusb 3610000.xhci: Host supports USB 3.1 Enhanced SuperSped [ 5.011053] INITRAMF STARTS [ 5.152558] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 5.155058] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber1 [ 5.157593] usb usb2: Product: xHCI Host Controller [ 5.159282] usb usb2: Manufacturer: Linux 4.14.102-rt53-tegra xhci-hcd [ 5.161586] usb usb2: SerialNumber: 3610000.xhci [ 5.163519] usb usb1: usb_suspend_both: status 0 [ 5.165655] hub 2-0:1.0: USB hub found [ 5.166976] hub 2-0:1.0: 4 ports detected Getting target_board from device-tree ... [ 5.313690] EXT4-fs (vblkdev0p1): recovery complete [ 5.316496] EXT4-fs (vblkdev0p1): mounted filesystem with ordered data mode.) [ 5.406033] Trying chroot to /new_root [ 5.407583] INITRAMFS END [ 5.542396] systemd[1]: System time before build time, advancing clock. [ 5.573816] ip_tables: (C) 2000-2006 Netfilter Core Team [ 5.594312] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SE) [ 5.603708] systemd[1]: Detected architecture arm64. Welcome to Ubuntu 18.04.2 LTS! [ 5.617603] systemd[1]: Set hostname to . ��pExec_L0_Init failed ��[ 5.700576] systemd[1]: File /lib/systemd/system/systemd-journald.service:. [ 5.707249] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warn) [ 5.826132] random: systemd: uninitialized urandom read (16 bytes read) [ 5.829748] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 5.834195] random: systemd: uninitialized urandom read (16 bytes read) [ 5.836774] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 5.840764] random: systemd: uninitialized urandom read (16 bytes read) [ 5.843652] systemd[1]: Started Forward Password Requests to Wall Directory . [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 5.849949] systemd[1]: Set up automount Arbitrary Executable File Formats F. [ OK ] Set up automount Arbitrary Executab��…rmats File System Automount Poin. [ 5.857148] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Reached target Slices. [ OK ] Created slice system-getty.slice. [ OK ] Listening on Journal Socket. Starting Load Kernel Modules... Starting Create list of required st��…ce nodes for the current kernel.. [ 5.885355] usb 1-1: new high-speed USB device number 2 using tegra-xusb Mounting POSIX Message Queue File System... [ OK ] Listening on Journal Socket (/dev/log). Starting Remount Root and Kernel File Systems... [ OK ] Listening on udev Kernel Socket. [ OK ] Listening on udev Control Socket. Starting udev Coldplug all Devices... [[ 5.908962] usbcore: registered new interface driver rndis_host OK ] Listening on Journal Audit Socket. [ OK ] Listening on Network Service Netlink Socket. Mounting Huge Pages File System... Mounting Kernel Debug File System... [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Paths. [ OK ] Reached target Local Encrypted Volumes. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Reached target Swap. Starting Set CPUs online service... [ OK ] Listening on Syslog Socket. [ 5.961186] iommu: Adding device 0000:04:00.0 to group 17 [ 5.964343] atlantic 0000:04:00.0: enabling device (0000 -> 0002) Starting Journal Service... [ OK ] Started Create list of required sta��…vice nodes for the current kerne. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted Kernel Debug File System. [ OK ] Started Set CPUs online service. Starting Reset time to FS install time... Starting Load/Save Random Seed... [ 6.045278] usb 1-1: New USB device found, idVendor=0bda, idProduct=5401 [ 6.048029] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 6.051013] usb 1-1: Product: USB3.0 Hub [ 6.052635] usb 1-1: Manufacturer: Realtek [ 6.077850] hub 1-1:1.0: USB hub found Starting Create Static Device Nodes in /dev... [ 6.082159] hub 1-1:1.0: 4 ports detected [ OK ] Started Reset time to FS install time. [ 6.098747] carmel_ras carmel_ras: Deferring probe, arm64_ras hasnt been prot [ 6.103699] carmel_ras carmel_ras: Deferring probe, arm64_ras hasnt been prot [ OK ] Started Load/Save Random Seed. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting udev Kernel Device Manager... [ OK ] Started udev Kernel Device Manager. [ 6.389364] usb 1-1.4: new low-speed USB device number 3 using tegra-xusb [ OK ] Started Journal Service. [ 6.500821] usb 1-1.4: New USB device found, idVendor=258a, idProduct=1006 [ 6.503519] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumbe0 [ 6.506364] usb 1-1.4: Product: USB KEYBOARD [ 6.507897] usb 1-1.4: Manufacturer: SINO WEALTH Starting Flush Journal to Persistent Storage... [ 6.678912] input: SINO WEALTH USB KEYBOARD as /devices/3610000.xhci/usb1/1-0 [ 6.696780] carmel_ras carmel_ras: Deferring probe, arm64_ras hasnt been prot [ 6.697638] iommu: Adding device 0004:01:00.0 to group 19 [ 6.702246] atlantic 0004:01:00.0: enabling device (0000 -> 0002) [ 6.785418] hid-generic 0003:258A:1006.0001: input,hidraw0: USB HID v1.10 Ke0 [ 6.788251] systemd-journald[479]: Received request to flush runtime journal1 [ 6.795635] carmel_ras carmel_ras: Deferring probe, arm64_ras hasnt been prot [ 6.896190] input: SINO WEALTH USB KEYBOARD as /devices/3610000.xhci/usb1/1-1 [ OK ] Started Flush Journal to Persistent Storage. [ 7.021638] hid-generic 0003:258A:1006.0002: input,hiddev96,hidraw1: USB HID1 [ 7.028816] carmel_ras carmel_ras: Deferring probe, arm64_ras hasnt been prot [ 7.053815] carmel_ras carmel_ras: Deferring probe, arm64_ras hasnt been prot Starting Create Volatile Files and Directories... [ 7.174287] atlantic 0000:04:00.0 enp4s0: renamed from eth1 [ OK ] Started Create Volatile Files and Directories. Starting Network Time Synchronization... [ 7.252311] carmel_ras carmel_ras: Deferring probe, arm64_ras hasnt been prot Starting Update UTMP about System Boot/Shutdown... [ 7.313372] usb 1-1.1: new low-speed USB device number 4 using tegra-xusb [ 7.360412] atlantic 0004:01:00.0 enP4p1s0: renamed from eth1 [ 7.370627] iommu: Adding device 0001:01:00.0 to group 18 [ 7.374882] nvgpu 0001:01:00.0: enabling device (0000 -> 0003) [ 7.421870] usb 1-1.1: New USB device found, idVendor=04f2, idProduct=0909 [ 7.424484] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumbe0 [ 7.427271] usb 1-1.1: Product: USB Optical Mouse [ 7.429023] usb 1-1.1: Manufacturer: PixArt [ OK ] Started Update UTMP about System Boot/Shutdown. [ 7.495825] nvgpu: 0001:01:00.0 nvgpu_nvhost_syncpt_init:291 [INFO0 [ 7.495825] [ 7.503809] carmel_ras carmel_ras: Deferring probe, arm64_ras hasnt been prot [ 7.553448] input: PixArt USB Optical Mouse as /devices/3610000.xhci/usb1/1-2 [ OK ] Started Network Time Synchronization. [ 7.586481] nvgpu: 17810000.vgpu gv11b_vgpu_probe:70 [INF0 [ 7.586481] [ 7.591317] hid-generic 0003:04F2:0909.0003: input,hidraw2: USB HID v1.11 Mo0 [ 7.592191] carmel_ras carmel_ras: Deferring probe, arm64_ras hasnt been prot [ 7.596737] carmel_ras carmel_ras: Deferring probe, arm64_ras hasnt been prot [ 7.730423] carmel_ras carmel_ras: Deferring probe, arm64_ras hasnt been prot [ 7.927257] loop: module loaded [ OK ] Started Load Kernel Modules. Mounting Kernel Configuration File System... Starting Apply Kernel Variables... [ OK ] Mounted Kernel Configuration File System. [ OK ] Started Apply Kernel Variables. Starting Network Service... [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Network is Online. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Found device /dev/ttyS0. [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. [ OK ] Started udev Coldplug all Devices. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting System Logging Service... Starting Permit User Sessions... [ OK ] Started D-Bus System Message Bus. Starting mnand refresh daemon service... [ OK ] Started Check and update firmware v��…AQC100 and AQC107 network device. [ OK ] Started nv_tos_daemon_service assis��…re storage TA with FS operations. [ OK ] Started Message of the Day. Starting Initialization of TACP... Starting Login Service... [ OK ] Started Hypervisor initiated Shutdown Service. Starting Board specific initialization... [ OK ] Started System Logging Service. Starting mnand-rfsh demon for vblkdev0 ... [ OK ] Started Permit User Sessions. Starting board specific init ... [ OK ] Started Getty on tty1. Getting target_board from device-tree ... Starting Drive Setup Service... [ OK ] Started Login Service. Starting mnand-rfsh demon for vblkdev2 ... [ 11.732909] bash[640]: flashtools version is 3.3.0. Starting mnand-rfsh demon for vblkdev4 ... Starting mnand-rfsh demon for mmcblk0 ... [ OK ] Started mnand refresh daemon service. [ 11.982060] bash[640]: 0000:04:00.0 up to date with firmware 3.1.73 [ OK ] Started Drive Setup Service. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Initialization of TACP. Starting Sync/Update RTC time... [ OK ] Started SPI TP daemon. [ OK ] Started Fan control daemon. [ OK ] Started Update UTMP about System Runlevel Changes. [ 12.131827] bash[640]: 0004:01:00.0 up to date with firmware 3.1.73 �� [0x000000001CEEFCEF] : [ LOG ] : Tegra FuSaState: FUSA_INIT_STATE [0x000000001CEF3BB9] : [ LOG ] : Tegra FuSaManager ServiceId Log: [0x000000001CEF70C4] : [ LOG ] : ServiceId 0: 0x2100800 [0x000000001D1530F6] : [ INFO ] : Tegra Safe Startup Timed Out [0x000000001D1531F4] : [ INFO ] : Tegra FuSa State: FUSA_ERROR_STATE��target=ea [ OK ] Started Board specific initialization. [ OK ] Reached target Companion services for Nvidia Tegra. Ubuntu 18.04.2 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: ��Unable to access /dev/vblk_mnand1 Formatting /driveupdate/tmp partition ... mkqnx6fs: unable to access '/dev/vblk_mnand1' - No such file or directory mount: Can't mount /driveupdate/tmp (type qnx6) mount: Possible reason: Invalid argument [WARNING] Cannot mount /dev/vblk_mnand1 to /driveupdate/tmp Unable to access /dev/vblk_mnand2 Formatting /driveupdate/data partition ... mkqnx6fs: unable to access '/dev/vblk_mnand2' - No such file or directory mount: Can't mount /driveupdate/data (type qnx6) mount: Possible reason: Invalid argument [WARNING] Cannot mount /dev/vblk_mnand2 to /driveupdate/data mkdir: /driveupdate/data: Function not implemented mkdir: /driveupdate/data/log: Function not implemented [WARNING] Failed to create drive update log directory SSH and Qconn initialized [INFO][17:51:07]DU-TII start...