[0000.184] I> Welcome to MB2(TBoot-BPMP)(version: 01.00.160913-t186-M-00.00-mobile-e75fdd51) [0000.193] I> Boot-device: eMMC [0000.200] I> sdmmc bdev is already initialized [0000.205] I> pmic: reset reason (nverc) : 0x80 [0000.238] I> Found 19 partitions in SDMMC_BOOT (instance 3) [0000.258] I> Found 33 partitions in SDMMC_USER (instance 3) [0000.264] W> No valid slot number is found in scratch register [0000.269] W> Return default slot: _a [0000.273] I> A/B: bin_type (16) slot 0 [0000.276] I> Loading partition bpmp-fw at 0xd7800000 [0000.281] I> Reading two headers - addr:0xd7800000 blocks:1 [0000.287] I> Addr: 0xd7800000, start-block: 29417480, num_blocks: 1 [0000.313] I> Binary(16) of size 534416 is loaded @ 0xd7800000 [0000.319] W> No valid slot number is found in scratch register [0000.324] W> Return default slot: _a [0000.328] I> A/B: bin_type (17) slot 0 [0000.331] I> Loading partition bpmp-fw-dtb at 0xd79f0000 [0000.337] I> Reading two headers - addr:0xd79f0000 blocks:1 [0000.342] I> Addr: 0xd79f0000, start-block: 29419896, num_blocks: 1 [0000.362] I> Binary(17) of size 113248 is loaded @ 0xd79e4400 [0000.390] I> Loading SCE-FW ... [0000.393] W> No valid slot number is found in scratch register [0000.399] W> Return default slot: _a [0000.402] I> A/B: bin_type (12) slot 0 [0000.406] I> Loading partition sce-fw at 0xd7300000 [0000.410] I> Reading two headers - addr:0xd7300000 blocks:1 [0000.416] I> Addr: 0xd7300000, start-block: 29423992, num_blocks: 1 [0000.436] I> Binary(12) of size 125632 is loaded @ 0xd7300000 [0000.441] I> Init SCE [0000.444] I> Loading APE-FW ... [0000.447] W> No valid slot number is found in scratch register [0000.452] W> Return default slot: _a [0000.456] I> A/B: bin_type (11) slot 0 [0000.459] I> Loading partition adsp-fw at 0xd7400000 [0000.464] I> Reading two headers - addr:0xd7400000 blocks:1 [0000.470] I> Addr: 0xd7400000, start-block: 29401096, num_blocks: 1 [0000.489] I> Binary(11) of size 77216 is loaded @ 0xd7400000 [0000.495] I> Copy BTCM section [0000.498] W> No valid slot number is found in scratch register [0000.504] W> Return default slot: _a [0000.507] I> A/B: bin_type (13) slot 0 [0000.511] I> Loading partition cpu-bootloader at 0x96000000 [0000.516] I> Reading two headers - addr:0x96000000 blocks:1 [0000.522] I> Addr: 0x96000000, start-block: 29380616, num_blocks: 1 [0000.544] I> Binary(13) of size 309152 is loaded @ 0x96000000 [0000.550] W> No valid slot number is found in scratch register [0000.555] W> Return default slot: _a [0000.559] I> A/B: bin_type (20) slot 0 [0000.562] I> Loading partition bootloader-dtb at 0x85205400 [0000.568] I> Reading two headers - addr:0x85205400 blocks:1 [0000.573] I> Addr: 0x85205400, start-block: 29382664, num_blocks: 1 [0000.594] I> Binary(20) of size 192320 is loaded @ 0x85205400 [0000.599] W> No valid slot number is found in scratch register [0000.605] W> Return default slot: _a [0000.608] I> A/B: bin_type (14) slot 0 [0000.612] I> Loading partition secure-os at 0x85305600 [0000.617] I> Reading two headers - addr:0x85305600 blocks:1 [0000.623] I> Addr: 0x85305600, start-block: 29384712, num_blocks: 1 [0000.646] I> Binary(14) of size 402864 is loaded @ 0x85305600 [0000.653] I> TOS boot-params @ 0x85000000 [0000.657] I> TOS params prepared [0000.660] I> Loading EKS ... [0000.663] I> A/B: bin_type (15) slot 0 [0000.667] I> Loading partition eks at 0x85905800 [0000.671] I> Reading two headers - addr:0x85905800 blocks:1 [0000.677] I> Addr: 0x85905800, start-block: 29397000, num_blocks: 1 [0000.696] I> Binary(15) of size 1040 is loaded @ 0x85905800 [0000.701] I> EKB detected (length: 0x400) @ 0x85905800 [0000.707] I> Copied encrypted keys [0000.710] I> boot profiler @ 0x175844000 [0000.714] I> boot profiler for TOS @ 0x175844000 [0000.719] I> Unhalting SCE [0000.721] I> Primary Memory Start:80000000 Size:70000000 [0000.727] I> Extended Memory Start:f0110000 Size:856f0000 [0000.733] I> MB2(TBoot-BPMP) done NOTICE: BL31: v1.3(release):b5eeb33 NOTICE: BL31: Built : 02:21:00, Apr 17 2022 ipc-unittest-main: 1519: Welcome to IPC unittest!!! ipc-unittest-main: 1531: waiting forever ipc-unittest-srv: 329: Init unittest services!!! hwkey-agent: 41: hwkey-agent is running!! hwkey-agent: 347: key_mgnt_processing ....... hwkey-agent: 255: Setting EKB key 0 to slot 14 hwkey-agent: 178: Init hweky-agent services!! luks-srv: 40: luks-srv is running!! luks-srv: 157: Init luks-srv IPC services!! platform_bootstrap_epilog: trusty bootstrap complete [0000.955] I> Welcome to Cboot [0000.958] I> Cboot Version: t186-acf1ddbd [0000.962] I> CPU-BL Params @ 0x175800000 [0000.965] I> 0) Base:0x00000000 Size:0x00000000 [0000.970] I> 1) Base:0x177f00000 Size:0x00100000 [0000.974] I> 2) Base:0x177e00000 Size:0x00100000 [0000.979] I> 3) Base:0x177d00000 Size:0x00100000 [0000.983] I> 4) Base:0x177c00000 Size:0x00100000 [0000.988] I> 5) Base:0x177b00000 Size:0x00100000 [0000.992] I> 6) Base:0x177800000 Size:0x00200000 [0000.997] I> 7) Base:0x177400000 Size:0x00400000 [0001.002] I> 8) Base:0x177a00000 Size:0x00100000 [0001.006] I> 9) Base:0x177300000 Size:0x00100000 [0001.011] I> 10) Base:0x176800000 Size:0x00800000 [0001.015] I> 11) Base:0x30000000 Size:0x00040000 [0001.020] I> 12) Base:0xf0000000 Size:0x00100000 [0001.024] I> 13) Base:0x30040000 Size:0x00001000 [0001.028] I> 14) Base:0x30048000 Size:0x00001000 [0001.033] I> 15) Base:0x30049000 Size:0x00001000 [0001.037] I> 16) Base:0x3004a000 Size:0x00001000 [0001.042] I> 17) Base:0x3004b000 Size:0x00001000 [0001.046] I> 18) Base:0x3004c000 Size:0x00001000 [0001.051] I> 19) Base:0x3004d000 Size:0x00001000 [0001.055] I> 20) Base:0x3004e000 Size:0x00001000 [0001.059] I> 21) Base:0x3004f000 Size:0x00001000 [0001.064] I> 22) Base:0x00000000 Size:0x00000000 [0001.068] I> 23) Base:0xf0100000 Size:0x00010000 [0001.073] I> 24) Base:0x00000000 Size:0x00000000 [0001.077] I> 25) Base:0x00000000 Size:0x00000000 [0001.082] I> 26) Base:0x00000000 Size:0x00000000 [0001.086] I> 27) Base:0x00000000 Size:0x00000000 [0001.090] I> 28) Base:0x84400000 Size:0x00400000 [0001.095] I> 29) Base:0x30000000 Size:0x00010000 [0001.099] I> 30) Base:0x178000000 Size:0x08000000 [0001.104] I> 31) Base:0x00000000 Size:0x00000000 [0001.108] I> 32) Base:0x176000000 Size:0x00600000 [0001.113] I> 33) Base:0x80000000 Size:0x70000000 [0001.117] I> 34) Base:0xf0110000 Size:0x856f0000 [0001.122] I> 35) Base:0x00000000 Size:0x00000000 [0001.126] I> 36) Base:0x00000000 Size:0x00000000 [0001.130] I> 37) Base:0x1772e0000 Size:0x00020000 [0001.135] I> 38) Base:0x84000000 Size:0x00400000 [0001.139] I> 39) Base:0x96000000 Size:0x02000000 [0001.144] I> 40) Base:0x85000000 Size:0x01200000 [0001.148] I> 41) Base:0x175800000 Size:0x00500000 [0001.153] I> 42) Base:0x00000000 Size:0x00000000 [0001.157] I> 43) Base:0x00000000 Size:0x00000000 [0001.162] GIC-SPI Target CPU: 4 [0001.165] Interrupts Init done [0001.168] calling constructors [0001.171] initializing heap [0001.174] initializing threads [0001.177] initializing timers [0001.180] creating bootstrap completion thread [0001.185] top of bootstrap2() [0001.188] CPU: ARM Cortex A57 [0001.192] CPU: MIDR: 0x411FD073, MPIDR: 0x80000100 [0001.197] initializing platform [0001.200] I> Bl_dtb @0x85205400 [0001.203] I> gpio framework initialized [0001.208] I> tegrabl_gpio_driver_register: register 'nvidia,tegra186-gpio' driver [0001.217] I> tegrabl_gpio_driver_register: register 'nvidia,tegra186-gpio-aon' driver [0001.224] I> GPIO framework and drivers are initialized. [0001.230] I> Boot-device: eMMC [0001.241] I> sdmmc bdev is already initialized [0001.271] I> Found 19 partitions in SDMMC_BOOT (instance 3) [0001.289] I> Found 33 partitions in SDMMC_USER (instance 3) [0001.295] W> opt-in fuse is not set, skip fuse_burning [0001.300] I> Reserved memory at 0xfbe00000 for U-Boot relocation [0001.305] W> No valid slot number is found in scratch register [0001.311] W> Return default slot: _a [0001.322] I> A/B: bin_type (21) slot 0 [0001.325] I> Loading kernel-dtb from partition [0001.330] I> Loading partition kernel-dtb at 0x80000000 from device(0x1) [0001.351] I> Kernel_dtb @0x80000000 [0001.354] I> tegrabl_tca9539_init: i2c bus: 0, slave addr: 0xee [0001.362] W> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539 [0001.372] W> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539 [0001.380] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0001.386] I> tegrabl_tca9539_init: i2c bus: 0, slave addr: 0xe8 [0001.394] W> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539 [0001.404] W> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539 [0001.412] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0001.419] I> fixed regulator driver initialized [0001.442] I> register 'maxim' power off handle [0001.447] I> virtual i2c enabled [0001.450] I> registered 'maxim,max77620' pmic [0001.454] I> tegrabl_gpio_driver_register: register 'max77620-gpio' driver [0001.464] E> failed to read label property for node 149928: 13 [0001.471] E> failed to read reg property for node 150024: 13 [0001.478] E> failed to read reg property for node 150076: 13 [0001.484] E> failed to read label property for node 150160: 13 [0001.491] E> failed to read reg property for node 150228: 13 [0001.498] E> failed to read reg property for node 150300: 13 [0001.505] I> Find /i2c@c250000's alias i2c7 [0001.509] I> Reading eeprom i2c=7 address=0x50 [0001.539] I> Device at /i2c@c250000:0x50 [0001.542] I> Reading eeprom i2c=7 address=0x57 [0001.547] E> I2C: slave not found in slaves. [0001.551] E> I2C: Could not write 0 bytes to slave: 0x00ae with repeat start true. [0001.559] E> I2C_DEV: Failed to send register address 0x00000000. [0001.565] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xae at 0x00000000 via instance 7. [0001.574] E> eeprom: Failed to read I2C slave device [0001.579] I> Eeprom read failed 0x3526070d [0001.583] I> Find /i2c@3160000's alias i2c0 [0001.587] I> Reading eeprom i2c=0 address=0x50 [0001.592] E> I2C: slave not found in slaves. [0001.596] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true. [0001.604] E> I2C_DEV: Failed to send register address 0x00000000. [0001.610] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0x00000000 via instance 0. [0001.619] E> eeprom: Failed to read I2C slave device [0001.624] I> Eeprom read failed 0x3526070d [0001.629] I> Find /i2c@3180000's alias i2c2 [0001.633] I> Reading eeprom i2c=2 address=0x54 [0001.637] I> Enabling gpio chip_id = 2, gpio pin = 9 [0001.642] C> GPIO driver for chip_id 0x2 could not be found [0001.647] E> cam_eeprom_read: Can't get gpio driver [0001.652] I> Eeprom read failed 0x4d4d000d [0001.656] I> Reading eeprom i2c=2 address=0x57 [0001.660] I> Enabling gpio chip_id = 2, gpio pin = 9 [0001.665] C> GPIO driver for chip_id 0x2 could not be found [0001.670] E> cam_eeprom_read: Can't get gpio driver [0001.675] I> Eeprom read failed 0x4d4d000d [0001.679] I> create_pm_ids: id: 3636-0001-300-H, len: 15 [0001.684] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0001.707] I> regulator 'vdd-hdmi-5v0' already enabled [0001.718] I> regulator 'vdd-hdmi-5v0' already enabled [0001.723] I> hdmi cable connected [0001.728] I> setting 'vdd-pex-1v00' regulator to 1000000 micro volts [0001.736] I> setting 'vdd-1v8' regulator to 1800000 micro volts [0001.742] I> retrieved tmds range from prod_list_hdmi_soc [0001.748] E> cannot find any other nvdisp nodes [0001.768] I> edid read success [0001.783] I> edid read success [0001.786] I> width = 640, height = 480, frequency = 25174825 [0001.791] I> width = 640, height = 480, frequency = 25174825 [0001.797] I> width = 640, height = 480, frequency = 25174825 [0001.802] I> width = 640, height = 480, frequency = 25174825 [0001.807] I> width = 1920, height = 1080, frequency = 148500000 [0001.813] I> width = 1366, height = 768, frequency = 85500000 [0001.819] I> width = 1920, height = 540, frequency = 74250000 [0001.824] I> width = 1920, height = 1080, frequency = 148351648 [0001.830] I> width = 1280, height = 720, frequency = 74175824 [0001.836] I> width = 720, height = 480, frequency = 26973026 [0001.841] I> width = 1920, height = 1080, frequency = 74175824 [0001.847] I> width = 1920, height = 1080, frequency = 74175824 [0001.852] I> Best mode Width = 1920, Height = 1080, freq = 148351648 [0001.861] I> hdmi_enable, starting HDMI initialisation [0001.869] I> hdmi_enable, HDMI initialisation complete [0001.882] initializing target [0001.885] calling apps_init() [0001.888] starting app kernel_boot_app [0001.911] I> found decompressor handler: lz4-legacy [0001.916] I> decompressing BMP blob ... [0001.928] I> Kernel type = Normal [0001.931] I> ########## Fixed storage boot ########## [0001.936] I> Loading kernel-bootctrl from partition [0001.941] I> Loading partition kernel-bootctrl at 0xa8000000 from device(0x1) [0001.958] W> tegrabl_get_kernel_bootctrl: magic number(0x00000000) is invalid [0001.965] W> tegrabl_get_kernel_bootctrl: use default dummy boot control data [0001.972] W> No valid slot number is found in scratch register [0001.977] W> Return default slot: _a [0001.981] I> A/B: bin_type (24) slot 0 [0001.997] I> Boot image size read from image header: 9902d [0002.002] I> Boot image load address: 0x80400000 [0002.007] I> Loading kernel from partition [0002.011] I> Loading partition kernel at 0x80400000 from device(0x1) [0003.309] I> Validate kernel ... [0003.312] I> T18x: Authenticate kernel (bin_type 24), max size 0x4000000 [0003.320] I> Decrypt the buffer ... [0003.323] W> tegrabl_decrypt_block: fuse (0x0) is not burnt to do encryption (0x4); skip decryption. [0003.332] I> done [0003.334] I> Checking boot.img header magic ... [0003.338] I> [OK] [0003.340] I> kernel-dtb is already loaded [0003.343] I> Validate kernel-dtb ... [0003.347] I> T18x: Authenticate kernel-dtb (bin_type 21), max size 0x100000 [0003.354] I> Decrypt the buffer ... [0003.357] W> tegrabl_decrypt_block: fuse (0x0) is not burnt to do encryption (0x4); skip decryption. [0003.366] I> done [0003.368] I> Kernel hdr @0x80400000 [0003.371] I> Kernel dtb @0x80000000 [0003.375] I> decompressor handler not found [0003.379] I> Copying kernel image (626733 bytes) from 0x80400800 to 0x80600000 ... [0003.386] I> Done [0003.388] I> Move ramdisk (len: 0) from 0x8049a000 to 0x947d0000 [0003.395] I> Updated bpmp info to DTB [0003.400] I> Ramdisk: Base: 0x947d0000; Size: 0x0 [0003.404] I> Updated initrd info to DTB [0003.408] W> WARN: Fail to override "console=none" in commandline [0003.414] I> Active rootfs suffix: [0003.417] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0003.424] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0003.432] I> disabled_core_mask: 0xffffff0c [0003.436] W> No valid slot number is found in scratch register [0003.441] W> Return default slot: _a [0003.445] I> Active slot suffix: [0003.448] I> add_boot_slot_suffix: slot_suffix = [0003.452] I> Linux Cmdline: console=ttyS0,115200 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 isolcpus=1-2 video=tegrafb earlycon=uart8250,mmio32,0x3100000 nvdumper_reserved=0x1772e0000 gpt rootfs.slot_suffix= tegra_fbmem=0x800000@0x96085000 lut_mem=0x2008@0x96081000 usbcore.old_scheme_first=1 tegraid=18.1.2.0.0 maxcpus=6 no_console_suspend boot.slot_suffix= boot.ratchetvalues=0.2031647.1 vpr_resize bl_prof_dataptr=0x10000@0x175840000 sdhci_tegra.en_boot_part_access=1 [0003.499] I> Updated bootarg info to DTB [0003.503] W> MAC addr invalid! [0003.506] E> Failed to get WIFI MAC address [0003.510] W> MAC addr invalid! [0003.513] E> Failed to get Bluetooth MAC address [0003.517] I> eeprom_get_mac_addr: MAC (type: 2): 48:b0:2d:3b:6c:8e [0003.523] E> Found no plugin manager ids in source DT [0003.528] W> Add plugin manager ids from board info [0003.533] W> "plugin-manager" doesn't exist, creating [0003.538] W> "ids" doesn't exist, creating [0003.542] W> "connection" doesn't exist, creating [0003.546] W> "configs" doesn't exist, creating [0003.551] I> create_pm_ids: id: 3636-0001-300-H, len: 15 [0003.556] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0003.567] I> Adding plugin-manager/ids/3636-0001-300=/i2c@c250000:module@0x50 [0003.574] W> "i2c@c250000" doesn't exist, creating [0003.579] W> "module@0x50" doesn't exist, creating [0003.584] I> Adding plugin-manager/ids/3636-0001-300-H [0003.590] I> Adding plugin-manager/configs/3636-mem-type 00 [0003.596] I> Adding plugin-manager/configs/3636-power-config 00 [0003.602] I> Adding plugin-manager/configs/3636-misc-config 00 [0003.608] I> Adding plugin-manager/configs/3636-modem-config 00 [0003.614] I> Adding plugin-manager/configs/3636-touch-config 00 [0003.619] I> Adding plugin-manager/configs/3636-display-config 00 [0003.626] I> Adding plugin-manager/cvm [0003.629] W> "chip-id" doesn't exist, creating [0003.634] I> Adding plugin-manager/chip-id/A02P [0003.638] W> "odm-data" doesn't exist, creating [0003.643] I> Adding /chosen/plugin-manager/odm-data [0003.651] I> added [base:0x80000000, size:0x70000000] to /memory [0003.657] I> added [base:0xf0200000, size:0x85600000] to /memory [0003.662] I> added [base:0x175e00000, size:0x200000] to /memory [0003.668] I> added [base:0x176600000, size:0x200000] to /memory [0003.674] I> added [base:0x177000000, size:0x200000] to /memory [0003.680] I> Updated memory info to DTB [0003.684] E> add_disp_param: failed to get display params for du=1 [0003.691] W> "reset" doesn't exist, creating [0003.695] W> "pmc-reset-reason" doesn't exist, creating [0003.700] W> "pmic-reset-reason" doesn't exist, creating [0003.706] I> Adding ecid(000000016405d0c61000000012fb0240) to DT [0003.712] I> disabled_core_mask: 0xffffff0c [0003.721] I> Add serial number:1421921006588 as DT property [0003.728] I> Plugin-manager override starting [0003.733] I> node /plugin-manager/fragement@0 matches [0003.741] I> node /plugin-manager/fragement@3 matches [0003.754] I> Disable plugin-manager status in FDT [0003.759] I> Plugin-manager override finished successfully [0003.764] I> tegrabl_load_kernel_and_dtb: Done [0003.809] I> Kernel EP: 0x80600000, DTB: 0x80000000 U-Boot 2020.04-g4335beb (Apr 17 2022 - 02:21:01 -0700) SoC: tegra186 Model: NVIDIA P3636-0001 Board: NVIDIA P3636-0001 DRAM: 3.8 GiB MMC: sdhci@3400000: 1, sdhci@3460000: 0 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: Warning: ethernet@2490000 using MAC address from ROM eth0: ethernet@2490000 Hit any key to stop autoboot: 2  1  0 Card did not respond to voltage select! switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 858 bytes read in 33 ms (25.4 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 7238366 bytes read in 205 ms (33.7 MiB/s) Retrieving file: /boot/Image 34484232 bytes read in 830 ms (39.6 MiB/s) append: console=ttyS0,115200 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 isolcpus=1-2 video=tegrafb earlycon=uart8250,mmio32,0x3100000 nvdumper_reserved=0x1772e0000 gpt rootfs.slot_suffix= tegra_fbmem=0x800000@0x96085000 lut_mem=0x2008@0x96081000 usbcore.old_scheme_first=1 tegraid=18.1.2.0.0 maxcpus=6 no_console_suspend boot.slot_suffix= boot.ratchetvalues=0.2031647.1 vpr_resize bl_prof_dataptr=0x10000@0x175840000 sdhci_tegra.en_boot_part_access=1 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 isolcpus=1-2 ## Flattened Device Tree blob at 80000000 Booting using the fdt blob at 0x80000000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000080000000, end 0000000080033ed4 copying carveout for /host1x@13e00000/display-hub@15200000/display@15200000... copying carveout for /host1x@13e00000/display-hub@15200000/display@15210000... copying carveout for /host1x@13e00000/display-hub@15200000/display@15220000... Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x100 [ 0.000000] Linux version 4.9.253-tegra (buildbrain@mobile-u64-5374-d5000) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Sun Apr 17 02:37:44 PDT 2022 [ 0.000000] Boot CPU: AArch64 Processor [411fd073] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 80, [ 0.000000] OF: fdt: - 80000000 , 70000000 [ 0.000000] OF: fdt: - f0200000 , 85600000 [ 0.000000] OF: fdt: - 175e00000 , 200000 [ 0.000000] OF: fdt: - 176600000 , 200000 [ 0.000000] OF: fdt: - 177000000 , 200000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000003100000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] Found tegra_fbmem: 00800000@96085000 [ 0.000000] Found lut_mem: 00002008@96081000 [ 1.397495] imx219 9-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.405126] imx219 9-0010: board setup failed [ 1.433110] imx219 10-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.440790] imx219 10-0010: board setup failed [ 1.573093] mmc0: error -110 whilst initialising MMC card [ 1.707230] mmc0: error -110 whilst initialising MMC card [ 1.841426] mmc0: error -110 whilst initialising MMC card [ 2.019546] mmc0: error -110 whilst initialising MMC card [ 3.443957] sd 0:0:0:0: [sda] No Caching mode page found [ 3.449324] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 4.789234] usb usb1-port2: Cannot enable. Maybe the USB cable is bad? [ 5.749262] usb usb1-port2: Cannot enable. Maybe the USB cable is bad? [ 8.005262] usb usb1-port2: Cannot enable. Maybe the USB cable is bad? [ 8.961243] usb usb1-port2: Cannot enable. Maybe the USB cable is bad? [ 8.967853] usb usb1-port2: unable to enumerate USB device [ 95.8βΈ®