Ubuntu 18.04.6 LTS jet ttyS0 jet login: user Password: Last login: Ma oct 26 13:40:59 EEST 2021 on ttyS0 Welcome to Ubuntu 18.04.6 LTS (GNU/Linux 4.9.253-tegra aarch64) * Documentation: https://help.ubuntu.com * Management: https://landscape.canonical.com * Support: https://ubuntu.com/advantage 0 updates can be applied immediately. user@jet:~$ df -h / Filesystem Size Used Avail Use% Mounted on /dev/sda1 39G 28G 9,1G 76% / user@jet:~$ sudo shutdown -h now [ 1907.356369] systemd-shutdow: 25 output lines suppressed due to ratelimiting [ 1908.897344] IRQ10 no longer affine to CPU1 [ 1908.901615] CPU1: shutdown [ 1908.933176] IRQ11 no longer affine to CPU2 [ 1908.937431] CPU2: shutdown [ 1908.961298] IRQ12 no longer affine to CPU3 [ 1908.965559] CPU3: shutdown [ 1908.970201] reboot: Power down [0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-8728f3cb) [0000.130] Processing in cold boot mode Bootloader 2 [0000.135] A02 Bootrom Patch rev = 1023 [0000.138] Power-up reason: pmc por [0000.141] No Battery Present [0000.144] pmic max77620 reset reason [0000.147] pmic max77620 NVERC : 0x10 [0000.151] RamCode = 0 [0000.153] Platform has DDR4 type RAM [0000.156] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0xb10e8 [0000.172] Entering ramdump check [0000.175] Get RamDumpCarveOut = 0x0 [0000.178] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.188] Sdram initialization is successful [0000.192] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.198] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.204] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.210] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.233] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.256] Platform-DebugCarveout: 0 [0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.265] Non secure mode, and RB not enabled. [0000.269] BoardID = 3448, SKU = 0x0 [0000.272] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.276] Nano-SD: checking PT table on QSPI ... [0000.280] Initialize FailControl [0000.283] Read PT from (2:0) [0000.314] PT crc32 and magic check passed. [0000.318] Using BFS PT to query partitions [0000.324] Loading Tboot-CPU binary [0000.352] Verifying TBC in OdmNonSecureSBK mode [0000.362] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.369] Bootloader downloaded successfully. [0000.373] Downloaded Tboot-CPU binary to 0xa0000258 [0000.378] MAX77620_GPIO5 configured [0000.381] CPU power rail is up [0000.384] CPU clock enabled [0000.388] Performing RAM repair [0000.391] Updating A64 Warmreset Address to 0xa00002e9 [0000.396] BoardID = 3448, SKU = 0x0 [0000.399] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.403] Nano-SD: checking PT table on QSPI ... [0000.407] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.413] Loading NvTbootBootloaderDTB [0000.480] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.551] Bootloader DTB Load Address: 0x83000000 [0000.556] BoardID = 3448, SKU = 0x0 [0000.559] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.563] Nano-SD: checking PT table on QSPI ... [0000.567] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.573] Loading NvTbootKernelDTB [0000.639] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.711] Kernel DTB Load Address: 0x83100000 [0000.715] BoardID = 3448, SKU = 0x0 [0000.718] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.722] Nano-SD: checking PT table on QSPI ... [0000.726] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.734] Loading cboot binary [0000.850] Verifying EBT in OdmNonSecureSBK mode [0000.892] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.899] Bootloader downloaded successfully. [0000.903] BoardID = 3448, SKU = 0x0 [0000.906] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.910] Nano-SD: checking PT table on QSPI ... [0000.914] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.920] PT: Partition NCT NOT found ! [0000.924] Warning: Find Partition via PT Failed [0000.928] Next binary entry address: 0x92c00258 [0000.933] BoardId: 3448 [0000.938] Overriding pmu board id with proc board id [0000.942] Display board id is not available [0000.947] BoardID = 3448, SKU = 0x0 [0000.950] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.954] Nano-SD: checking PT table on QSPI ... [0000.958] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.065] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.121] /bpmp deleted [0001.123] SC7EntryFw header found loaded at 0xff700000 [0001.311] OVR2 PMIC [0001.312] Bpmp FW successfully loaded [0001.316] BoardID = 3448, SKU = 0x0 [0001.319] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.323] Nano-SD: checking PT table on QSPI ... [0001.327] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.334] WB0 init successfully at 0xff780000 [0001.339] Verifying NvTbootWb0 in OdmNonSecureSBK mode [0001.344] Set NvDecSticky Bits [0001.347] GSC2 address ff53fffc value c0edbbcc [0001.353] GSC MC Settings done [0001.356] BoardID = 3448, SKU = 0x0 [0001.360] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.363] Nano-SD: checking PT table on QSPI ... [0001.368] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.375] TOS Image length 53680 [0001.378] Monitor size 53680 [0001.381] OS size 0 [0001.396] Secure Os AES-CMAC Verification Success! [0001.400] TOS image cipher info: plaintext [0001.404] Loading and Validation of Secure OS Successful [0001.420] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.425] NvTbootPackSdramParams: start. [0001.430] NvTbootPackSdramParams: done. [0001.434] Tegraboot started after 51856 us [0001.438] Basic modules init took 935924 us [0001.442] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB [0001.447] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.453] Next stage binary read took 102860 us [0001.457] Carveout took -132464 us [0001.460] CPU initialization took 510367 us [0001.464] Total time taken by TegraBoot 1416687 us [0001.469] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):b5eeb33f7 NOTICE: BL31: Built : 12:09:37, Jul 26 2021 ERROR: Error initializing runtime service trusty_fast [0001.591] RamCode = 0 [0001.596] LPDDR4 Training: Read DT: Number of tables = 2 [0001.601] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.614] EMC Training Successful [0001.617] 408000 not found in DVFS table [0001.623] RamCode = 0 [0001.626] DT Write: emc-table@204000 succeeded [0001.632] DT Write: emc-table@1600000 succeeded [0001.636] LPDDR4 Training: Write DT: Number of tables = 2 [0001.684] [0001.685] Debug Init done [0001.688] Marked DTB cacheable [0001.691] Bootloader DTB loaded at 0x83000000 [0001.696] Marked DTB cacheable [0001.699] Kernel DTB loaded at 0x83100000 [0001.702] DeviceTree Init done [0001.715] Pinmux applied successfully [0001.720] gicd_base: 0x50041000 [0001.723] gicc_base: 0x50042000 [0001.726] Interrupts Init done [0001.730] Using base:0x60005090 & irq:208 for tick-timer [0001.736] Using base:0x60005098 for delay-timer [0001.740] platform_init_timer: DONE [0001.743] Timer(tick) Init done [0001.747] osc freq = 38400 khz [0001.751] [0001.752] Welcome to L4T Cboot [0001.755] [0001.756] Cboot Version: 00.00.2018.01-t210-c952b4e6 [0001.761] calling constructors [0001.764] initializing heap [0001.767] initializing threads [0001.770] initializing timers [0001.773] creating bootstrap completion thread [0001.777] top of bootstrap2() [0001.780] CPU: ARM Cortex A57 [0001.783] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.788] initializing platform [0001.795] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.799] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.804] Macronix QSPI chip present [0001.807] SPI device register [0001.810] init boot device [0001.813] allocating memory for boot device(SPI) [0001.817] registering boot device [0001.836] QSPI bdev is already initialized [0001.840] Enable APE clock [0001.842] Un-powergate APE partition [0001.846] of_register: registering tegra_udc to of_hal [0001.851] of_register: registering inv20628-driver to of_hal [0001.857] of_register: registering ads1015-driver to of_hal [0001.862] of_register: registering lp8557-bl-driver to of_hal [0001.868] of_register: registering bq2419x_charger to of_hal [0001.873] of_register: registering bq27441_fuel_gauge to of_hal [0001.885] gpio framework initialized [0001.888] of_register: registering tca9539_gpio to of_hal [0001.894] of_register: registering tca9539_gpio to of_hal [0001.899] of_register: registering i2c_bus_driver to of_hal [0001.904] of_register: registering i2c_bus_driver to of_hal [0001.910] of_register: registering i2c_bus_driver to of_hal [0001.916] pmic framework initialized [0001.919] of_register: registering max77620_pmic to of_hal [0001.925] regulator framework initialized [0001.928] of_register: registering tps65132_bl_driver to of_hal [0001.934] initializing target [0001.940] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.948] board ID = D78, board SKU = 0 [0001.952] Skipping Z3! [0001.957] fixed regulator driver initialized [0001.974] initializing OF layer [0001.977] NCK carveout not present [0001.980] Skipping dts_overrides [0001.984] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.001] I2C Bus Init done [0002.003] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.014] I2C Bus Init done [0002.016] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.026] I2C Bus Init done [0002.029] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.039] I2C Bus Init done [0002.042] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.052] I2C Bus Init done [0002.055] of_children_init: Ops found for compatible string maxim,max77620 [0002.065] max77620_init using irq 118 [0002.070] register 'maxim,max77620' pmic [0002.074] gpio_driver_register: register 'max77620-gpio' driver [0002.080] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.091] I2C Bus Init done [0002.094] NCK carveout not present [0002.104] Find /i2c@7000c000's alias i2c0 [0002.107] get eeprom at 1-a0, size 256, type 0 [0002.116] Find /i2c@7000c500's alias i2c2 [0002.120] get eeprom at 3-a0, size 256, type 0 [0002.124] get eeprom at 3-ae, size 256, type 0 [0002.129] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.134] I2C slave not started [0002.137] I2C write failed [0002.140] Writing offset failed [0002.143] eeprom_init: EEPROM read failed [0002.147] pm_ids_update: eeprom init failed [0002.151] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.181] pm_ids_update: The pm board id is 3448-0000-400 [0002.188] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.196] pm_ids_update: pm id update successful [0002.201] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.231] pm_ids_update: The pm board id is 3449-0000-400 [0002.237] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.245] pm_ids_update: pm id update successful [0002.275] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.281] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.289] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.295] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.303] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:f7:7c [0002.309] Plugin Manager: Parse ODM data 0x000a4000 [0002.322] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.336] Find /i2c@7000c000's alias i2c0 [0002.340] get eeprom at 1-a0, size 256, type 0 [0002.349] Find /i2c@7000c500's alias i2c2 [0002.352] get eeprom at 3-a0, size 256, type 0 [0002.357] get eeprom at 3-ae, size 256, type 0 [0002.361] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.367] I2C slave not started [0002.370] I2C write failed [0002.372] Writing offset failed [0002.375] eeprom_init: EEPROM read failed [0002.379] pm_ids_update: eeprom init failed [0002.383] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.413] pm_ids_update: The pm board id is 3448-0000-400 [0002.420] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.426] pm_ids_update: pm id update successful [0002.431] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.461] pm_ids_update: The pm board id is 3449-0000-400 [0002.467] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.474] pm_ids_update: pm id update successful [0002.505] Add serial number:1422919053267 as DT property [0002.512] Applying platform configs [0002.519] platform-init is not present. Skipping [0002.523] calling apps_init() [0002.529] Couldn't find GPT header [0002.534] Proceeding to Cold Boot [0002.537] starting app android_boot_app [0002.541] Device state: unlocked [0002.544] display console init [0002.552] could not find regulator [0002.575] hdmi cable not connected [0002.578] is_hdmi_needed: HDMI not connected,DT entry for leds-pwm not found [0002.589] returning false [0002.591] hdmi is not connected [0002.594] sor0 is not supported [0002.597] display_console_init: no valid display out_type [0002.605] subnode volume_up is not found ! [0002.609] subnode back is not found ! [0002.613] subnode volume_down is not found ! [0002.617] subnode menu is not found ! [0002.621] Gpio keyboard init success [0002.701] found decompressor handler: lz4-legacy [0002.715] decompressing blob (type 1)... [0002.782] display_resolution: No display init [0002.786] Failed to retrieve display resolution [0002.790] Could not load/initialize BMP blob...ignoring [0002.867] decompressor handler not found [0002.870] load_firmware_blob: Firmware blob loaded, entries=2 [0002.876] XUSB blob version 0 size 126464 @ 0x92ca828c [0002.882] -------> se_aes_verify_sbk_clear: 747 [0002.886] se_aes_verify_sbk_clear: Error [0002.890] SE operation failed [0002.893] bl_battery_charging: connected to external power supply [0002.902] display_console_ioctl: No display init [0002.907] switch_backlight failed [0002.913] device_query_partition_size: failed to open partition spiflash0:MSC ! [0002.920] MSC Partition not found [0002.927] device_query_partition_size: failed to open partition spiflash0:USP ! [0002.934] USP partition read failed! [0002.937] blob_init: blob-partition USP header read failed [0002.943] android_boot Unable to update recovery partition [0002.948] kfs_getpartname: name = LNX [0002.952] Loading kernel from LNX [0002.961] Found 19 BFS partitions in "spiflash0" [0003.286] load kernel from storage [0003.291] decompressor handler not found [0003.560] Successfully loaded kernel and ramdisk images [0003.565] board ID = D78, board SKU = 0 [0003.570] sdmmc node status = okay [0003.573] sdcard instance = 0 [0003.576] sdmmc cd-inverted [0003.579] sdcard gpio handle 0x5b [0003.582] sdcard gpio pin 0xc9 [0003.585] sdcard gpio flags 0x0 [0003.588] vmmc-supply 0x9d [0003.591] cd_gpio_pin = 201 [0003.593] pin_state = 0 [0003.596] Found sdcard [0003.598] SD-card IS present ... [0003.601] load_and_boot_kernel: SD card detected OK [0003.607] display_resolution: No display init [0003.611] Failed to retrieve display resolution [0003.616] bmp blob is not loaded and initialized [0003.620] Failed to display boot-logo [0003.624] NCK carveout not present [0003.627] Skipping dts_overrides [0003.630] NCK carveout not present [0003.640] Find /i2c@7000c000's alias i2c0 [0003.644] get eeprom at 1-a0, size 256, type 0 [0003.652] Find /i2c@7000c500's alias i2c2 [0003.656] get eeprom at 3-a0, size 256, type 0 [0003.660] get eeprom at 3-ae, size 256, type 0 [0003.665] pm_ids_update: Updating 1,a0, size 256, type 0 [0003.670] I2C slave not started [0003.673] I2C write failed [0003.676] Writing offset failed [0003.679] eeprom_init: EEPROM read failed [0003.683] pm_ids_update: eeprom init failed [0003.687] pm_ids_update: Updating 3,a0, size 256, type 0 [0003.717] pm_ids_update: The pm board id is 3448-0000-400 [0003.724] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0003.732] pm_ids_update: pm id update successful [0003.737] pm_ids_update: Updating 3,ae, size 256, type 0 [0003.767] pm_ids_update: The pm board id is 3449-0000-400 [0003.773] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0003.781] pm_ids_update: pm id update successful [0003.811] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0003.817] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0003.825] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0003.831] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0003.839] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:f7:7c [0003.845] Plugin Manager: Parse ODM data 0x000a4000 [0003.858] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0003.866] Add serial number:1422919053267 as DT property [0003.875] "bpmp" doesn't exist, creating [0003.880] Updated bpmp info to DTB [0003.885] Updated initrd info to DTB [0003.889] "proc-board" doesn't exist, creating [0003.895] Updated board info to DTB [0003.898] "pmu-board" doesn't exist, creating [0003.904] Updated board info to DTB [0003.907] "display-board" doesn't exist, creating [0003.913] Updated board info to DTB [0003.917] "reset" doesn't exist, creating [0003.921] Updated reset info to DTB [0003.925] display_console_ioctl: No display init [0003.929] display_console_ioctl: No display init [0003.934] display_console_ioctl: No display init [0003.938] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 gpt [0003.973] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0003.978] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0003.992] Updated bootarg info to DTB [0003.996] Adding uuid 0000000164445740180000000e050280 to DT [0004.001] Adding eks info 0 to DT [0004.007] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0004.013] Updated memory info to DTB [0004.020] set vdd_core voltage to 1125 mv [0004.024] setting 'vdd-core' regulator to 1125000 micro volts [0004.030] Found secure-pmc; disable BPMP U-Boot 2020.04-g46e4604c78 (Jul 26 2021 - 12:09:42 -0700) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB OK In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 starting USB... Bus usb@7d000000: tegrausb: Invalid dr_mode 2 for host mode probe failed, error -1 Bus xusb@70090000: Firmware size 126464 Firmware timestamp: 0x5f23e558, Version: 50.26 release Register HCSParams1: 9000124 NbrPorts: 9 Starting the controller USB XHCI 1.00 scanning bus xusb@70090000 for devices... Device not responding to set address. USB device not accepting new address (error=80000000) 4 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found resetting USB... Bus usb@7d000000: tegrausb: Invalid dr_mode 2 for host mode probe failed, error -1 Bus xusb@70090000: Firmware size 126464 Firmware timestamp: 0x5f23e558, Version: 50.26 release Register HCSParams1: 9000124 NbrPorts: 9 Starting the controller USB XHCI 1.00 scanning bus xusb@70090000 for devices... Device not responding to set address. USB device not accepting new address (error=80000000) 4 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found no usb devices available Card did not respond to voltage select! Card did not respond to voltage select! Device 0: unknown device Warning: eth_rtl8169 using MAC address from ROM BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 Abort missing environment variable: pxeuuid missing environment variable: bootfile Retrieving file: pxelinux.cfg/01-00-04-4b-e6-f7-7c *** ERROR: `serverip' not set missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000000 *** ERROR: `serverip' not set missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000000 *** ERROR: `serverip' not set missing environment variable: bootfile Retrieving file: pxelinux.cfg/000000 *** ERROR: `serverip' not set missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000 *** ERROR: `serverip' not set missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000 *** ERROR: `serverip' not set missing environment variable: bootfile Retrieving file: pxelinux.cfg/000 *** ERROR: `serverip' not set missing environment variable: bootfile Retrieving file: pxelinux.cfg/00 *** ERROR: `serverip' not set missing environment variable: bootfile Retrieving file: pxelinux.cfg/0 *** ERROR: `serverip' not set missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm-tegra210-p3450-0000 *** ERROR: `serverip' not set missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm-tegra210 *** ERROR: `serverip' not set missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm *** ERROR: `serverip' not set missing environment variable: bootfile Retrieving file: pxelinux.cfg/default *** ERROR: `serverip' not set Config file not found Tegra210 (P3450-0000) # usb reset resetting USB... Bus usb@7d000000: tegrausb: Invalid dr_mode 2 for host mode probe failed, error -1 Bus xusb@70090000: Firmware size 126464 Firmware timestamp: 0x5f23e558, Version: 50.26 release Register HCSParams1: 9000124 NbrPorts: 9 Starting the controller USB XHCI 1.00 scanning bus xusb@70090000 for devices... Device not responding to set address. USB device not accepting new address (error=80000000) 4 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Tegra210 (P3450-0000) # ### remove and reinsert USB ### Tegra210 (P3450-0000) # usb reset resetting USB... Bus usb@7d000000: tegrausb: Invalid dr_mode 2 for host mode probe failed, error -1 Bus xusb@70090000: Firmware size 126464 Firmware timestamp: 0x5f23e558, Version: 50.26 release Register HCSParams1: 9000124 NbrPorts: 9 Starting the controller USB XHCI 1.00 scanning bus xusb@70090000 for devices... 5 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Tegra210 (P3450-0000) #