[0000.062] I> MB1 (version: 0.32.0.0-t234-54845784-57325615) [0000.068] I> t234-A01-0-Silicon (0x12347) Prod [0000.072] I> Boot-mode : Coldboot [0000.075] I> Emulation: [0000.078] I> Entry timestamp: 0x00000000 [0000.081] I> last_boot_error: 0x0 [0000.084] I> BR-BCT: preprod_dev_sign: 0 [0000.088] I> rst_source: 0x0, rst_level: 0x0 [0000.092] I> Task: Bootchain select WAR set (0x5000ba65) [0000.097] I> Task: Enable SLCG (0x5000bab1) [0000.101] I> Task: CRC check (0x5001ea19) [0000.105] I> Skip FUSE records CRC check as records_integrity fuse is not burnd [0000.113] I> Task: Initialize MB2 params (0x5000cb51) [0000.118] I> MB2-params @ 0x40060000 [0000.121] I> Task: Crypto init (0x5001d981) [0000.125] I> Task: Secure debug controls (0x5000c0a9) [0000.130] I> Task: strap war set (0x5000ba2d) [0000.135] I> Task: Initialize SOC Therm (0x5001bd35) [0000.139] I> Task: Program NV master stream id (0x5000c05d) [0000.145] I> Task: Verify boot mode (0xd4820f1) [0000.151] I> Task: Alias fuses (0x5001095d) [0000.155] W> FUSE_ALIAS: Fuse alias on production fused part is not supported. [0000.162] I> Task: Print SKU type (0x5000f5f1) [0000.167] I> FUSE_OPT_CCPLEX_CLUSTER_DISABLE = 0x00000000 [0000.172] I> FUSE_OPT_GPC_DISABLE = 0x00000000 [0000.176] I> FUSE_OPT_TPC_DISABLE = 0x00000000 [0000.180] I> FUSE_OPT_DLA_DISABLE = 0x00000000 [0000.185] I> FUSE_OPT_PVA_DISABLE = 0x00000000 [0000.189] I> FUSE_OPT_NVENC_DISABLE = 0x00000000 [0000.193] I> FUSE_OPT_NVDEC_DISABLE = 0x00000000 [0000.198] I> FUSE_OPT_FSI_DISABLE = 0x00000000 [0000.202] I> FUSE_OPT_EMC_DISABLE = 0x00000000 [0000.206] I> FUSE_BOOTROM_PATCH_VERSION = 0x7 [0000.210] I> FUSE_PSCROM_PATCH_VERSION = 0x7 [0000.215] I> FUSE_OPT_ADC_CAL_FUSE_REV = 0x2 [0000.219] I> FUSE_SKU_INFO_0 = 0xd0 [0000.222] I> FUSE_OPT_SAMPLE_TYPE_0 = 0x3 PS [0000.226] I> FUSE_PACKAGE_INFO_0 = 0x2 [0000.230] I> SKU: Prod [0000.232] I> Task: Boost clocks (0x500148a1) [0000.236] I> Initializing PLLC2 for AXI_CBB. [0000.240] I> AXI_CBB : src = 35, divisor = 0 [0000.244] I> Task: Voltage monitor (0x50014b49) [0000.249] I> VMON: Vmon re-calibration and fine tuning done [0000.254] I> Task: UPHY init (0x5000d065) [0000.260] I> HSIO UPHY init done [0000.263] E> Skipping GBE UPHY config [0000.267] I> Task: Boot device init (0x50000be9) [0000.271] I> Boot_device: QSPI_FLASH instance: 0 [0000.276] I> Qspi clock source : pllc_out0 [0000.280] I> QSPI Flash: Macronix 64MB [0000.283] I> QSPI-0l initialized successfully [0000.288] I> Task: TSC init (0x50020a4d) [0000.292] I> Task: Load membct (0x50011fe9) [0000.296] I> RAM_CODE 0x4000401 [0000.299] I> Loading MEMBCT [0000.301] I> Slot: 0 [0000.303] I> Binary[0] block-0 (partition size: 0x40000) [0000.309] I> get_binary_info: Binary name: MEM-BCT-0 [0000.313] I> Size of crypto header is 8192 [0000.317] I> BCH load address is : 0x40050000 [0000.322] I> Size of crypto header is 8192 [0000.326] I> BCH of MEM-BCT-0 read from storage [0000.330] I> BCH address is : 0x40050000 [0000.334] I> MEM-BCT-0 header integrity check is success [0000.339] I> Binary magic in BCH component 0 is MEM0 [0000.344] I> component binary type is 0 [0000.348] I> MEM-BCT-0 binary is read from storage [0000.353] I> MEM-BCT-0 binary integrity check is success [0000.358] I> Binary MEM-BCT-0 loaded successfully at 0x40040000 (0xe580) [0000.365] I> RAM_CODE 0x4000401 [0000.370] I> RAM_CODE 0x4000401 [0000.374] I> Task: Load Page retirement list (0x500115b1) [0000.379] I> Task: SDRAM params override (0x50011fc5) [0000.384] I> Task: Save mem-bct info (0x50014fa1) [0000.389] I> Task: Carveout allocate (0x50015005) [0000.393] I> RCM blob carveout will not be allocated [0000.398] I> ECC region[0]: Start:0x0, End:0x0 [0000.402] I> ECC region[1]: Start:0x0, End:0x0 [0000.407] I> ECC region[2]: Start:0x0, End:0x0 [0000.411] I> ECC region[3]: Start:0x0, End:0x0 [0000.415] I> ECC region[4]: Start:0x0, End:0x0 [0000.419] I> Non-ECC region[0]: Start:0x80000000, End:0x880000000 [0000.425] I> Non-ECC region[1]: Start:0x0, End:0x0 [0000.430] I> Non-ECC region[2]: Start:0x0, End:0x0 [0000.435] I> Non-ECC region[3]: Start:0x0, End:0x0 [0000.439] I> Non-ECC region[4]: Start:0x0, End:0x0 [0000.449] I> allocated(CO:44) base:0x849800000 size:0x36800000 align: 0x100000 [0000.456] I> allocated(CO:31) base:0x840000000 size:0x8000000 align: 0x8000000 [0000.463] I> allocated(CO:43) base:0x83c000000 size:0x4000000 align: 0x200000 [0000.470] I> allocated(CO:20) base:0x83a000000 size:0x2000000 align: 0x2000000 [0000.477] I> allocated(CO:24) base:0x838000000 size:0x2000000 align: 0x2000000 [0000.484] I> allocated(CO:28) base:0x836000000 size:0x2000000 align: 0x2000000 [0000.492] I> allocated(CO:29) base:0x834000000 size:0x2000000 align: 0x2000000 [0000.499] I> allocated(CO:22) base:0x848000000 size:0x1000000 align: 0x1000000 [0000.506] I> allocated(CO:41) base:0x833000000 size:0x1000000 align: 0x100000 [0000.513] I> allocated(CO:35) base:0x832200000 size:0xe00000 align: 0x10000 [0000.520] I> allocated(CO:02) base:0x849000000 size:0x800000 align: 0x800000 [0000.526] I> allocated(CO:03) base:0x831800000 size:0x800000 align: 0x800000 [0000.533] I> allocated(CO:06) base:0x831000000 size:0x800000 align: 0x800000 [0000.540] I> allocated(CO:10) base:0x830800000 size:0x800000 align: 0x800000 [0000.547] I> allocated(CO:56) base:0x830000000 size:0x800000 align: 0x200000 [0000.554] I> allocated(CO:07) base:0x82fc00000 size:0x400000 align: 0x400000 [0000.561] I> allocated(CO:33) base:0x82f800000 size:0x400000 align: 0x200000 [0000.568] I> allocated(CO:23) base:0x832000000 size:0x200000 align: 0x200000 [0000.575] I> allocated(CO:01) base:0x82f700000 size:0x100000 align: 0x100000 [0000.582] I> allocated(CO:04) base:0x82f600000 size:0x100000 align: 0x100000 [0000.589] I> allocated(CO:05) base:0x82f500000 size:0x100000 align: 0x100000 [0000.596] I> allocated(CO:08) base:0x82f400000 size:0x100000 align: 0x100000 [0000.603] I> allocated(CO:09) base:0x82f300000 size:0x100000 align: 0x100000 [0000.610] I> allocated(CO:15) base:0x82f200000 size:0x100000 align: 0x100000 [0000.617] I> allocated(CO:17) base:0x82f100000 size:0x100000 align: 0x100000 [0000.623] I> allocated(CO:27) base:0x82f000000 size:0x100000 align: 0x100000 [0000.630] I> allocated(CO:42) base:0x82ef00000 size:0x100000 align: 0x100000 [0000.637] I> allocated(CO:54) base:0x82ee80000 size:0x80000 align: 0x80000 [0000.644] I> allocated(CO:34) base:0x82ee70000 size:0x10000 align: 0x10000 [0000.651] I> allocated(CO:47) base:0x82ea00000 size:0x400000 align: 0x200000 [0000.658] I> allocated(CO:72) base:0x82e800000 size:0x200000 align: 0x10000 [0000.665] I> allocated(CO:48) base:0x82ee50000 size:0x20000 align: 0x10000 [0000.671] I> allocated(CO:69) base:0x82ee30000 size:0x20000 align: 0x10000 [0000.678] I> allocated(CO:49) base:0x82ee20000 size:0x10000 align: 0x10000 [0000.685] I> allocated(CO:50) base:0x82ee10000 size:0x10000 align: 0x10000 [0000.691] I> allocated(CO:52) base:0x82ee00000 size:0x10000 align: 0x10000 [0000.698] I> NSDRAM base: 0x80000000, end: 0x82ee70000 [0000.703] I> Task: Thermal check (0x50021d55) [0000.707] I> max_chip_limit = 105 [0000.711] I> min_chip_limit = -28 [0000.714] I> max temp read = 29 [0000.717] I> min temp read = 26 [0000.720] I> Task: Update FSI SCR with thermal fuse data (0x50021e61) [0000.726] I> Task: Enable WDT 5th expiry (0x50021a41) [0000.731] I> Task: I2C register (0x50000b85) [0000.735] I> Task: Reset FSI (0x500148b1) [0000.739] I> Task: Pinmux init (0x5001397d) [0000.743] I> Task: Prod config init (0x50013ddd) [0000.748] I> Task: Pad voltage init (0x50013a2d) [0000.752] I> Task: Prod init (0x50013e21) [0000.756] I> Task: Common rail init (0x50014575) [0000.761] I> DONE: Thermal config [0000.765] W> DEVICE_PROD: module = 13, instance = 4 not found in device prod. [0000.773] I> DONE: SOC rail config [0000.777] W> PMIC_CONFIG: Rail: MEMIO rail config not found in MB1 BCT. [0000.783] I> DONE: MEMIO rail config [0000.787] I> DONE: GPU rail info [0000.790] I> DONE: CV rail info [0000.793] I> Task: Mem clock src (0x50011de9) [0000.797] I> Task: Misc. board config (0x5001461d) [0000.802] W> PMIC_CONFIG: Platform config not found in MB1 BCT. [0000.807] I> Task: SDRAM init (0x50011ded) [0000.811] I> SDRAM-params @ 0xd485000 [0000.815] I> MemoryType: 4 MemBctRevision: 9 [0000.822] I> MSS code-drop: NvBootSdramInit [0000.826] I> MSS CAR: PLLM/HUB programming for MemoryType: 4 and MemBctRevisio9 [0000.833] I> MSS CAR: PLLM/HUB programming for MemoryType: 4 and MemBctRevisio9 [0000.840] I> MSS CAR: Init PLLM [0000.843] I> MSS CAR: Init PLLHUB [0000.848] I> Encryption: MTS: en, TX: en, VPR: en, GSC: en [0000.860] I> mb1_sdram_init Done ! [0000.863] I> SDRAM Size in Total 0x800000000 [0000.867] I> Task: Dram Ecc scrub (0x500116f5) [0000.871] I> Task: DRAM alias check (0x50011fbd) [0000.904] I> Task: Program NSDRAM carveout (0x50015961) [0000.910] I> NSDRAM carveout encryption is enabled [0000.915] I> Program NSDRAM carveout [0000.919] I> Task: Register checker (0x50011fc1) [0000.928] I> Task: Enable clock-mon (0x50020a35) [0000.944] I> FMON: Fmon re-programming done [0000.949] I> Task: Mapper init (0x5001ef4d) [0000.954] I> Task: SC7 Context Init (0x50020d3d) [0000.960] I> Task: CCPLEX IST init (0x5000c925) [0000.966] I> Task: CPU WP0 (0x5000bb15) [0000.971] I> Loading MCE [0000.973] I> Slot: 0 [0000.976] I> Binary[8] block-0 (partition size: 0x80000) [0000.982] I> get_binary_info: Binary name: MCE [0000.986] I> Size of crypto header is 8192 [0000.991] I> BCH load address is : 0x4003e000 [0000.996] I> Size of crypto header is 8192 [0001.001] I> BCH of MCE read from storage [0001.005] I> BCH address is : 0x4003e000 [0001.010] I> MCE header integrity check is success [0001.016] I> Binary magic in BCH component 0 is MTSM [0001.021] I> component binary type is 8 [0001.025] I> Size of crypto header is 8192 [0001.032] I> MCE binary is read from storage [0001.037] I> MCE binary integrity check is success [0001.042] I> Binary MCE loaded successfully at 0x40000000 (0x2c880) [0001.049] I> Size of crypto header is 8192 [0001.064] I> Size of crypto header is 8192 [0001.069] I> Sending WP0 mailbox command to PSC [0001.079] I> Task: XUSB Powergate (0x50000b91) [0001.084] I> Skipping powergate XUSB. [0001.088] I> Task: MB1 fixed firewalls (0x5002006d) [0001.100] W> Firewall readback mismatch [0001.104] W> Firewall readback mismatch [0001.112] W> Firewall readback mismatch [0001.122] I> Task: Load bpmp-fw (0x500203c9) [0001.128] I> Slot: 0 [0001.130] I> Binary[15] block-0 (partition size: 0x180000) [0001.136] I> get_binary_info: Binary name: BPMP_FW [0001.141] I> Size of crypto header is 8192 [0001.146] I> BCH load address is : 0x807fe000 [0001.151] I> Size of crypto header is 8192 [0001.156] I> BCH of BPMP_FW read from storage [0001.161] I> BCH address is : 0x807fe000 [0001.166] I> BPMP_FW header integrity check is success [0001.171] I> Binary magic in BCH component 0 is BPMF [0001.177] I> component binary type is 15 [0001.181] I> Size of crypto header is 8192 [0001.196] I> BPMP_FW binary is read from storage [0001.203] I> BPMP_FW binary integrity check is success [0001.209] I> Binary BPMP_FW loaded successfully at 0x80000000 (0xfddc0) [0001.217] I> Slot: 0 [0001.219] I> Binary[16] block-10000 (partition size: 0x400000) [0001.226] I> get_binary_info: Binary name: BPMP_FW_DTB [0001.232] I> Size of crypto header is 8192 [0001.236] I> BCH load address is : 0x807fc000 [0001.241] I> Size of crypto header is 8192 [0001.246] I> BCH of BPMP_FW_DTB read from storage [0001.251] I> BCH address is : 0x807fc000 [0001.256] I> BPMP_FW_DTB header integrity check is success [0001.262] I> Binary magic in BCH component 0 is BPMD [0001.268] I> component binary type is 16 [0001.272] I> Size of crypto header is 8192 [0001.278] I> BPMP_FW_DTB binary is read from storage [0001.284] I> BPMP_FW_DTB binary integrity check is success [0001.290] I> Binary BPMP_FW_DTB loaded successfully at 0x807db9f0 (0x20480) [0001.299] I> Task: Load psc-fw (0x50020551) [0001.304] I> Slot: 0 [0001.306] I> Binary[17] block-0 (partition size: 0xc0000) [0001.313] I> get_binary_info: Binary name: PSC_FW [0001.318] I> Size of crypto header is 8192 [0001.322] I> BCH load address is : 0x80ffe000 [0001.327] I> Size of crypto header is 8192 [0001.332] I> BCH of PSC_FW read from storage [0001.337] I> BCH address is : 0x80ffe000 [0001.342] I> PSC_FW header integrity check is success [0001.347] I> Binary magic in BCH component 0 is PFWP [0001.353] I> component binary type is 17 [0001.357] I> Size of crypto header is 8192 [0001.366] I> PSC_FW binary is read from storage [0001.371] I> PSC_FW binary integrity check is success [0001.377] I> Binary PSC_FW loaded successfully at 0x80000000 (0x59980) [0001.385] I> Task: Load nvdec-fw (0x500205c5) [0001.391] I> Slot: 0 [0001.393] I> Binary[7] block-0 (partition size: 0x100000) [0001.399] I> get_binary_info: Binary name: NVDEC [0001.404] I> Size of crypto header is 8192 [0001.409] I> BCH load address is : 0x800fe000 [0001.414] I> Size of crypto header is 8192 [0001.419] I> BCH of NVDEC read from storage [0001.423] I> BCH address is : 0x800fe000 [0001.428] I> NVDEC header integrity check is success [0001.434] I> Binary magic in BCH component 0 is NDEC [0001.439] I> component binary type is 7 [0001.443] I> Size of crypto header is 8192 [0001.451] I> NVDEC binary is read from storage [0001.456] I> NVDEC binary integrity check is success [0001.462] I> Binary NVDEC loaded successfully at 0x80000000 (0x46000) [0001.469] I> Size of crypto header is 8192 [0001.487] I> Task: Load tsec-fw (0x5002097d) [0001.493] I> TSEC-FW load support not enabled [0001.497] I> Task: GPIO interrupt map (0x500147b5) [0001.503] I> Task: SC7 context save (0x50020d79) [0001.509] I> Slot: 0 [0001.511] I> Binary[27] block-0 (partition size: 0x100000) [0001.518] I> get_binary_info: Binary name: BR_BCT [0001.523] I> Size of crypto header is 8192 [0001.527] I> Size of crypto header is 8192 [0001.532] I> BR_BCT binary is read from storage [0001.537] I> BR_BCT binary integrity check is success [0001.543] I> Binary BR_BCT loaded successfully at 0xa0000000 (0x2000) [0001.550] I> Slot: 0 [0001.553] I> Binary[13] block-0 (partition size: 0x30000) [0001.559] I> get_binary_info: Binary name: SC7-FW [0001.564] I> Size of crypto header is 8192 [0001.568] I> Size of crypto header is 8192 [0001.573] I> BCH load address is : 0xa0002000 [0001.578] I> Size of crypto header is 8192 [0001.583] I> BCH of SC7-FW read from storage [0001.588] I> BCH address is : 0xa0002000 [0001.593] I> SC7-FW header integrity check is success [0001.598] I> Binary magic in BCH component 0 is WB0B [0001.604] I> component binary type is 13 [0001.608] I> Size of crypto header is 8192 [0001.614] I> SC7-FW binary is read from storage [0001.620] I> SC7-FW binary integrity check is success [0001.625] I> Binary SC7-FW loaded successfully at 0xa0004000 (0x26db0) [0001.633] I> Slot: 0 [0001.635] I> Binary[22] block-0 (partition size: 0x30000) [0001.641] I> get_binary_info: Binary name: PSC_RF [0001.647] I> Size of crypto header is 8192 [0001.651] I> Size of crypto header is 8192 [0001.656] I> BCH load address is : 0xa002adb0 [0001.661] I> Size of crypto header is 8192 [0001.666] I> BCH of PSC_RF read from storage [0001.670] I> BCH address is : 0xa002adb0 [0001.676] I> PSC_RF header integrity check is success [0001.681] I> Binary magic in BCH component 0 is PSCR [0001.686] I> component binary type is 22 [0001.691] I> Size of crypto header is 8192 [0001.697] I> PSC_RF binary is read from storage [0001.702] I> PSC_RF binary integrity check is success [0001.707] I> Binary PSC_RF loaded successfully at 0xa002cdb0 (0x1b140) [0001.730] I> Task: Save WP0 payload to SC7 ctx (0x50021725) [0001.737] I> Task: Load MB2rf binary to SC7 ctx (0x500216b9) [0001.744] I> Slot: 0 [0001.746] I> Binary[14] block-0 (partition size: 0x20000) [0001.752] I> get_binary_info: Binary name: MB2_RF [0001.757] I> Size of crypto header is 8192 [0001.762] I> Size of crypto header is 8192 [0001.766] I> BCH load address is : 0xa00d6a48 [0001.772] I> Size of crypto header is 8192 [0001.776] I> BCH of MB2_RF read from storage [0001.781] I> BCH address is : 0xa00d6a48 [0001.786] I> MB2_RF header integrity check is success [0001.792] I> Binary magic in BCH component 0 is MB2R [0001.797] I> component binary type is 14 [0001.801] I> Size of crypto header is 8192 [0001.807] I> MB2_RF binary is read from storage [0001.813] I> MB2_RF binary integrity check is success [0001.818] I> Binary MB2_RF loaded successfully at 0xa00d8a48 (0x1bfa0) [0001.826] I> Task: Save Fuse-Bypass data to SC7 ctx (0x50021621) [0001.834] W> FUSE_ALIAS: Fuse alias on production fused part is not supported. [0001.841] I> SC7 context fuse-bypass data is empty [0001.846] I> Task: Save PMIC data to SC7 ctx (0x5002144d) [0001.853] I> Task: Save I2C bus freq data to SC7 ctx (0x500213d9) [0001.860] I> Task: Save SOCTherm data to SC7 ctx (0x50021365) [0001.867] I> Task: Save FMON data to SC7 ctx (0x500212f1) [0001.873] I> Task: Save VMON data to SC7 ctx (0x50021279) [0001.879] I> Task: Save TZDRAM data to SC7 ctx (0x5002178d) [0001.886] I> Task: Save GPIO int data to SC7 ctx (0x50021561) [0001.893] I> Task: Save clock data to SC7 ctx (0x50021205) [0001.899] I> Task: Save debug data to SC7 ctx (0x50021191) [0001.910] I> SC7 context save done [0001.914] I> Task: Load MB2/Applet/FSKP (0x5000ca55) [0001.920] I> Loading MB2 [0001.923] I> Slot: 0 [0001.925] I> Binary[6] block-0 (partition size: 0x80000) [0001.931] I> get_binary_info: Binary name: MB2 [0001.936] I> Size of crypto header is 8192 [0001.941] I> BCH load address is : 0x8007e000 [0001.946] I> Size of crypto header is 8192 [0001.951] I> BCH of MB2 read from storage [0001.955] I> BCH address is : 0x8007e000 [0001.960] I> MB2 header integrity check is success [0001.966] I> Binary magic in BCH component 0 is MB2B [0001.971] I> component binary type is 6 [0001.975] I> Size of crypto header is 8192 [0001.984] I> MB2 binary is read from storage [0001.990] I> MB2 binary integrity check is success [0001.995] I> Binary MB2 loaded successfully at 0x80000000 (0x68ee0) [0002.003] I> Task: Map CCPLEX SHARED carveout (0x5000cbf9) [0002.010] I> Task: Prepare MB2 params (0x5000cca9) [0002.017] I> BR-BCT Boot Chain Fields [0002.020] I> u32_non_gpio_select_boot_chain : 0 [0002.026] I> u32_num_boot_chains : 2 [0002.031] I> bf_bl_gpio_select_boot_chain_1b : 0 [0002.036] I> Task: Dram ecc test (0x50011791) [0002.041] I> Task: Misc NV security settings (0x5000c529) [0002.048] I> NVDEC sticky bits programming done [0002.053] I> Successfully powergated NVDEC [0002.057] I> Task: Disable/Reload WDT (0x50021a99) [0002.063] I> Task: Program misc carveouts (0x50015381) [0002.069] I> Program IPC carveouts [0002.076] I> SLCG Global override status := 0x0 [0002.081] I> MB1: MSS reconfig completed I> MB2 (version: 0.0.0.0-t234-54845784-9c429857) I> t234-A01-0-Silicon (0x12347) I> Boot-mode : Coldboot I> Emulation: I> Entry timestamp: 0x00206bdf I> Regular heap: [base:0x40040000, size:0x10000] I> DMA heap: [base:0x830000000, size:0x800000] I> Task: ARI update carveout TZDRAM (0x50001e80) I> Task: Enable hot-plug capability (0x50026c6c) I> Task: PSC mailbox init (0x50016a7c) I> Task: Crypto init (0x500065a8) I> Task: Enable GP-SE clock (0x50001fe4) I> Task: DICE Identity init (0x50019e50) I> DICE is not enabled. I> Task: OEM SC7 context save init (0x50019550) I> Task: I2C register (0x50001e44) I> Task: Map CCPLEX_INTERWORLD_SHMEM carveout (0x50001e2c) I> Task: Program CBB PCIE AMAP regions (0x50019b64) I> Task: Boot device init (0x50001d74) I> Boot_device: QSPI_FLASH instance: 0 I> Qspi clock source : pllc_out0 I> QSPI-0l initialized successfully I> Task: Partition Manager Init (0x50001d70) I> Found 57 partitions in QSPI_FLASH (instance 0) W> Cannot find any partition table for 00000003 > PARTITION_MANAGER: Failed to publish partition. I> Found 11 partitions in SDMMC_USER (instance 3) I> Task: Load and authenticate registered FWs (0x5001ce48) I> Task: Load AUXP FWs (0x5002680c) I> Successfully register SPE FW load task with MB2 loader I> Skipping SCE FW load I> Successfully register RCE FW load task with MB2 loader I> Successfully register DCE FW load task with MB2 loader I> Unpowergating APE I> Unpowergate done I> Successfully register APE FW load task with MB2 loader I> Skipping FSI FW load I> Successfully register XUSB FW load task with MB2 loader I> Partition name: A_spe-fw I> Size of partition: 589824 I> Binary@ device:3/0 block-55040 (partition size: 0x90000), name: A_spe-fw I> Partition name: A_rce-fw I> Size of partition: 1048576 I> Binary@ device:3/0 block-56192 (partition size: 0x100000), name: A_rce-fw I> spe: Authentication Finalize Done I> Binary spe loaded successfully at 0x82f400000 I> Partition name: A_dce-fw I> Size of partition: 5242880 I> Binary@ device:3/0 block-44800 (partition size: 0x500000), name: A_dce-fw I> rce: Authentication Finalize Done I> Binary rce loaded successfully at 0x82f100000 I> dce : oem authentication of header done I> dce : meta-blob integrity check is success. I> dce : will be decompressed at 0x83a000000 I> version 1 Bin 1 BCheckSum 0 content_size 0 Content ChkSum 1 reserved_00 0 I> Reserved10 0 BlockMaxSize 5 Reserved11 0 I> dce : decompressed to 9509936 bytes I> dce: plain binary integrity check is success I> Partition name: A_adsp-fw I> Size of partition: 2097152 I> Binary@ device:3/0 block-58240 (partition size: 0x200000), name: A_adsp-fw I> dce: Authentication Finalize Done I> Binary dce loaded successfully at 0x83a000000 I> Partition name: A_xusb-fw I> Size of partition: 262144 I> Binary@ device:3/0 block-9472 (partition size: 0x40000), name: A_xusb-fw I> ape: Authentication Finalize Done I> Binary ape loaded successfully at 0x82fc00000 I> xusb: Authentication Finalize Done I> Binary xusb loaded successfully at 0x82f500000 I> Task: Carveout setup (0x5001f55c) I> Program remaining OEM carveouts I> Task: Enable FSITHERM (0x50016950) I> Task: Enable FSI VMON (0x500164d8) I> FSI VMON: FSI Vmon re-calibration and fine tuning done I> Task: Validate FSI Therm readings (0x50016530) I> FSITHERM max temp = 29 I> FSITHERM min temp = 28 I> Task: Restore XUSB sec (0x50001d44) I> Task: Enable FSI SE clock (0x50016ed8) I> Enable FSI-SE clock and 10ms delay... I> Task: Initialize SBSA UART CAR (0x50001f48) I> Task: Ratchet update (0x50027d08) W> OPTIN fuse not set, skip ratchet update I> Task: Initialize CPUBL Params (0x50017e0c) I> CPUBL-params @ 0x836000000 I> Task: Prepare eeprom data (0x50017bd8) I> Task: FSI padctl context save (0x500196e0) I> Task: Unpowergate APE (0x50017640) W> mb2_unpowergate_ape: skip! APE is in unpowergated state I> Task: OEM firewalls (0x5002397c) I> OEM firewalls configured I> Task: Powergate APE (0x500177b4) I> Powergating APE I> Powergate done I> Task: OEM firewall restore saved settings (0x50023dd0) I> Task: Unhalt AUXPs (0x50026a74) I> Unhalting SPE.. I> Enabling combined UART ����spe: early_init vic initialized tsc initialized aon lic initialized spe: tag is 243b265b351d6bb9cc7b2e3acc5d90f8 spe: SafeRTOS v8.4 spe: init scheduler initialized aon hsp initialized tag initialized tcu initialized bpmp ipc initialized spe: late init cpu_nic clock initialized apb clock initialized pm initialized bpmp hsp initialized top1 hsp initialized ccplex ipc initialized spe: start scheduler �� I> Task: Trigger mailbox for PSC-BL1 exit (0x50016afc) I> Sending opcode 0x4d420802 to psc ��INFO: Entering psc_monitor_init! INFO: GSC22 BOM:0x848002000 SIZE:0x1000000 CLIENT_ACCESS1:00180000 INFO: PSCFW BUILD VERSION: 8a33b23-73b589c-8a15f76-rel-t234 INFO: mstatus:0xa00000808 INFO: Supervisor entry_point:c108c00 ��I> Received ACK from psc I> Tas��INFO: MONITOR: user task addr:0x848022000, blob offset:0x00020000 INFO: MONITOR: populated user images:13 INFO: mret to Supervisor! INFO: psc supervisor init. INFO: psc_irq_init... INFO: enter idle task. �� bpmp: socket 0 bpmp: base binary md5 is 1377b684fe55be78e1d7fc3e0f143b55 bpmp: combined binary md5 is 463f4d5b75234b74bb7f05b524d2a015 bpmp: firmware tag is 463f4d5b75234b74bb7f-1377b684fe5 initialized vwdt initialized mail_early initialized fuse initialized vfrel initialized hwwdt initialized adc fmon_populate_monitors: found 199 monitors initialized fmon initialized mc initialized reset initialized uphy_early initialized emc_early 471 clocks registered initialized clk_mach initialized clk_cal_early initialized clk_mach_early_config initialized io_dpd initialized soctherm initialized tj_init initialized regime initialized i2c vrmon_dt_init: vrmon node not found vrmon_chk_boot_state: found 0 rail monitors initialized vrmon initialized regulator ��k: Start secure NOR provision (0x5001997c) I> Task: Load FSI keyblob (0x50016f20) I> Skipping FSI key blob copy I> Task: Unhalt��initialized avfs_clk_platform initialized powergate �� AUXPs (0x50026a7c) I> SCE unhalt skipped I> Unhalting RCE I> RCE unhalt successful I> DCE unhal��initialized dvs initialized clk_mach_config initialized pm initialized suspend initialized strap initialized mce_dbell ��[ 2.543200] Camera-FW on t234-rce-safe started ��t s��TCU early console enabled. ��uccessful I> APE unhalt skipped I> FSI unhalt skipped I> Task: Load CPUBL (0x50017f04) I> Task: Load TOS (0x50018608) I> Task: Load and authenticate registered FWs (0x5001ce48) I> Partition name: A_cpu-bootloader I> Size of partition: 3670016 I> Binary@ device:3/0 block-24832 (partition size: 0x380000), name: A_cpu-bootlr �� ��initialized emc initialized emc_mrq initialized clk_cal initialized uphy_dt initialized uphy_mrq HSIO UPHY reset has been de-asserted 0x0 initialized uphy initialized pg_late initialized pg_mrq_init swdtimer_init: 0 reg polling start w period 47 ms initialized swdtimer initialized hwwdt_late initialized bwmgr initialized thermal_host_trip initialized thermal_mrq initialized oc_mrq initialized reset_mrq initialized mail_mrq initialized fmon_mrq initialized clk_mrq initialized avfs_mrq initialized i2c_mrq initialized tag_mrq initialized bwmgr_mrq initialized console_mrq ��I> Partition name: A_secure-os I> Size of partition: 4194304 I> Binary@ device:��missing prod DT calibration data for 199 fmons initialized clk_sync_fmon_post ��3/0 block-32000 (partition size: 0x400000), name: A_secure-os I> MB2-params @ 0x40060000 I> cpubl: Authentication Finalize Done I> Binary cpubl loaded successfully at 0x82ea00000 ��initialized clk_cal_late initialized noc_late initialized cvc ��I> tos: Authentication Finalize Done I> Binary tos loaded successfully��initialized avfs_clk_mach_post initialized avfs_clk_platform_post initialized cvc_late initialized rm initialized console_late handling unreferenced clks enable can1_core enable can1_host enable can2_core enable can2_host enable pwm3 enable mss_encrypt enable maud enable pllg_ref enable dsi_core enable aza_2xbit enable pllc4_muxed enable xusb_ss enable xusb_fs enable xusb_falcon enable xusb_core_mux enable dsi_lp enable sdmmc��[ 2.716215] Camera-FW on t234-rce-safe ready SHA1=97e50cbf (cm initialized clk_mach_post initialized pg_p�� total boot 187.024 m��ost initialized regulator_post initialized profile initialized fuse_late initialized mrq initialized patrol_scrubber initialized cactmon initialized extras_post bpmp: init complete ��s) �� at 0x83fdfe000 I> Relocating OP-TEE dtb from: 0x83feff770 to 0x82ee30000, size: 0x1976 I> [0] START: 0x80000000, SIZE: 0x7aee70000 I> [1] START: 0x836000000, SIZE: 0x2000000 I> Setting NS memory ranges to OP-TEE dtb finished. I> Partition name: A_eks I> Size of partition: 262144 I> Binary@ device:3/0 block-44288 (partition size: 0x40000), name: A_eks I> eks: Authentication Finalize Done I> Binary eks loaded successfully at 0x830000400 I> EKB detected (length: 0x410) @ VA:0x830000400 I> Task: Prepare TOS params (0x50018580) I> Setting EKB blob info to OPTEE dtb finished. I> Setting OPTEE arg3: 0x82ee30000 I> Task: OEM SC7 context save (0x500197dc) I> OEM sc7 context saved I> Task: Disable MSS perf stats (0x50026b08) I> Task: Program display sticky bits (0x50026a84) I> Task: Storage device deinit (0x50001eec) I> Task: SMMU external bypass disable (0x50016a60) I> Task: SMMU init (0x5001697c) I> Task: Program GICv3 registers (0x50026ba8) I> Task: Audit firewall settings (0x50023bd0) I> Task: Bootchain failure check (0x50002434) I> Current Boot-Chain Slot: 0 I> BR-BCT Boot-Chain is 0, and status is 1. Set UPDATE_BRBCT bit to 0 I> MB2 finished ��NOTICE: BL31: v2.6(release):07eea4970 NOTICE: BL31: Built : 07:55:15, Mar 19 2023 I/TC: ��DCE: FW Boot Done ��I/TC: Non-secure external DT found I/TC: OP-TEE version: 3.19 (gcc version 9.3.0 (Buildroot 2020.08)) #2 Sun Mar 14 I/TC: WARNING: This OP-TEE configuration might be insecure! I/TC: WARNING: Please check https://optee.readthedocs.io/en/latest/architecturel I/TC: Primary CPU initializing I/TC: WARNING: Test OEM keys are being used! I/TC: This is only for TZ-SE testing and should NOT be used for a shipping prod! I/TC: Primary CPU switching to normal world boot �� Jetson UEFI firmware (version 3.1-32827747 built on 2023-03-19T14:56:32+00:00) 3h Jetson UEFI firmware (version 3.1-32827747 built on 2023-03-19T14:56:32+00:00) ESC to enter Setup. F11 to enter Boot Manager Menu. Enter to continue boot. ** WARNING: Test Key is used. ** .... .. L4TLauncher: Attempting Direct Boot EFI stub: Booting Linux Kernel... EFI stub: Using DTB from configuration table EFI stub: Loaded initrd from LINUX_EFI_INITRD_MEDIA_GUID device path EFI stub: Exiting boot services and installing virtual address map...