[0000.180] [TegraBoot] (version 00.00.2014.50-mobile-d44d4bf0) [0000.186] Processing in cold boot mode Bootloader 2 [0000.190] A02 Bootrom Patch rev = 63 [0000.194] Power-up reason: reset button [0000.197] No Battery Present [0000.200] RamCode = 0 [0000.202] Platform has Ddr4 type ram [0000.206] max77620 disabling SD1 Remote Sense [0000.210] Setting Ddr voltage to 1125mv [0000.214] Serial Number of Pmic Max77663: 0x1601b0 [0000.221] Entering ramdump check [0000.224] Get RamDumpCarveOut = 0xff23f000 [0000.228] RamDumpCarveOut=0xff23f000, RamDumperFlag=0x0 [0000.234] Last reboot was clean, booting normally! [0000.238] Sdram initialization is successful [0000.242] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.248] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.253] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.258] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.263] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.268] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.273] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.279] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.294] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.299] Platform-DebugCarveout: 0 [0000.303] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.308] Non secure mode, and RB not enabled. [0000.348] Using GPT Primary to query partitions [0000.353] Loading Tboot-CPU binary [0000.402] Verifying bootloader in OdmNonSecureSBK mode [0000.412] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.419] Bootloader downloaded successfully. [0000.423] Downloaded Tboot-CPU binary to 0xa0000258 [0000.428] MAX77620_GPIO1 Configured. [0000.432] MAX77620_GPIO5 Configured. [0000.435] CPU power rail is up [0000.438] CPU clock enabled [0000.442] Performing RAM repair [0000.445] Updating A64 Warmreset Address to 0xa00002e9 [0000.473] Bootloader DTB Load Address: 0x83000000 [0000.501] Kernel DTB Load Address: 0x83100000 [0000.506] Loading cboot binary [0000.600] Verifying bootloader in OdmNonSecureSBK mode [0000.638] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.645] Bootloader downloaded successfully. [0000.649] GPT: Partition NOT found ! [0000.653] Find Partition via GPT Failed [0000.656] Find Partition via PT Failed [0000.660] function NvTbootGetBinaryOffsets: 0x1 error [0000.665] Error in NvTbootLoadBinary: 0x1 ! [0000.669] Next binary entry address: 0x92c00258 [0000.673] BoardId: 2180 [0000.678] dram memory type is 3 [0000.682] WB0 init successful [0000.708] Bpmp FW successfully loaded [0000.711] Set NvDecSticky Bits [0000.715] GSC1 address : ff700000 [0000.718] GSC2 address ff63fffc value c0edbbcc [0000.723] GSC2 address : ff600000 [0000.727] GSC3 address : ff500000 [0000.730] GSC4 address : ff400000 [0000.734] GSC5 address : ff300000 [0000.737] GSC MC Settings done [0000.741] TOS plaintext Image length 28752 [0000.745] Monitor size 28752 [0000.748] OS size 0 [0000.751] *** Secure OS image signature not verified *** [0000.756] Loading and Validation of Secure OS Successful [0000.761] NvTbootPackSdramParams: start. [0000.766] NvTbootPackSdramParams: done. [0000.770] Tegraboot started after 160163 us [0000.774] Basic modules init took 300851 us [0000.778] Sec Bootdevice Read Time = 216 ms, Read Size = 9476 KB [0000.784] Sec Bootdevice Write Time = -1940251271 ms, Write Size = -68719477 KB [0000.791] Next stage binary read took 23826 us [0000.795] Carveout took 207233 us [0000.798] CPU initialization took 96676 us [0000.802] Total time taken by TegraBoot 628586 us [0000.807] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.2(release):cc5fd7c NOTICE: BL31: Built : 00:37:02, Jul 20 2017 NOTICE: Trusty image missing. ERROR: Error initializing runtime service trusty_fast [0000.947] RamCode = 0 [0000.969] LPDDR4 Training: Read DT: Number of tables = 10 [0000.974] EMC Training (SRC-freq: 204000; DST-freq: 40800) [0000.979] EMC Training Skipped [0000.982] EMC Training (SRC-freq: 204000; DST-freq: 68000) [0000.987] EMC Training Skipped [0000.990] EMC Training (SRC-freq: 204000; DST-freq: 102000) [0000.995] EMC Training Skipped [0000.998] EMC Training (SRC-freq: 204000; DST-freq: 204000) [0001.003] EMC Training Skipped [0001.006] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0001.012] EMC Training Successful [0001.015] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0001.021] EMC Training Successful [0001.024] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.035] EMC Training Successful [0001.038] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.061] EMC Training Successful [0001.064] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.086] EMC Training Successful [0001.089] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.108] EMC Training Successful [0001.112] Switching to 800000 KHz Success [0001.121] RamCode = 0 [0001.125] DT Write: emc-table@40800 succeeded [0001.131] DT Write: emc-table@68000 succeeded [0001.137] DT Write: emc-table@102000 succeeded [0001.143] DT Write: emc-table@204000 succeeded [0001.149] DT Write: emc-table@408000 succeeded [0001.155] DT Write: emc-table@665600 succeeded [0001.161] DT Write: emc-table@800000 succeeded [0001.167] DT Write: emc-table@1065600 succeeded [0001.174] DT Write: emc-table@1331200 succeeded [0001.180] DT Write: emc-table@1600000 succeeded [0001.184] LPDDR4 Training: Write DT: Number of tables = 10 [0001.219] [0001.220] Debug Init done [0001.223] Marked DTB cacheable [0001.226] Bootloader DTB loaded at 0x83000000 [0001.231] Marked DTB cacheable [0001.234] Kernel DTB loaded at 0x83100000 [0001.238] DeviceTree Init done [0001.257] Pinmux applied successfully [0001.263] gicd_base: 0x50041000 [0001.267] gicc_base: 0x50042000 [0001.270] Interrupts Init done [0001.276] Using base:0x60005008 & irq:33 for tick-timer [0001.281] Using base:0x60005000 for delay-timer [0001.285] platform_init_timer: DONE [0001.289] Timer(tick) Init done [0001.294] osc freq = 38400 khz [0001.299] [0001.301] welcome to cboot [0001.303] [0001.304] Cboot Version: 00.00.2014.50-t210-fadd1be5 [0001.309] calling constructors [0001.312] initializing heap [0001.315] initializing threads [0001.318] initializing timers [0001.321] creating bootstrap completion thread [0001.325] top of bootstrap2() [0001.328] CPU: ARM Cortex A57 [0001.331] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.336] initializing platform [0001.382] config for ddr50 mode completed [0001.386] sdmmc bdev is already initialized [0001.390] Enable APE clock [0001.393] Un-powergate APE partition [0001.396] of_register: registering tegra_udc to of_hal [0001.401] of_register: registering inv20628-driver to of_hal [0001.407] of_register: registering ads1015-driver to of_hal [0001.412] of_register: registering lp8557-bl-driver to of_hal [0001.418] of_register: registering bq2419x_charger to of_hal [0001.424] of_register: registering cpc to of_hal [0001.428] of_register: registering bq27441_fuel_gauge to of_hal [0001.448] gpio framework initialized [0001.451] of_register: registering tca9539_gpio to of_hal [0001.457] of_register: registering tca9539_gpio to of_hal [0001.462] of_register: registering i2c_bus_driver to of_hal [0001.467] of_register: registering i2c_bus_driver to of_hal [0001.473] of_register: registering i2c_bus_driver to of_hal [0001.479] pmic framework initialized [0001.482] of_register: registering max77620_pmic to of_hal [0001.488] regulator framework initialized [0001.491] of_register: registering tegra_xhci to of_hal [0001.497] initializing target [0001.505] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.517] fixed regulator driver initialized [0001.589] initializing OF layer [0001.591] NCK carveout not present [0001.595] Skipping dts_overrides [0001.599] of_children_init: Ops found for compatible string nvidia,tegra210-xhci [0001.608] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.638] I2C Bus Init done [0001.641] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.656] I2C Bus Init done [0001.658] of_children_init: Ops found for compatible string ti,tca9539 [0001.673] tca9539_init: i2c bus: 2, slave addr: 0xe8 [0001.678] gpio_driver_register: register 'tca9539_gpio_driver' driver [0001.684] of_children_init: Ops found for compatible string ti,tca9539 [0001.699] tca9539_init: i2c bus: 2, slave addr: 0xee [0001.704] I2C slave not started [0001.707] I2C write failed [0001.709] i2c write failed [0001.712] Slave: 0xee, Register 0x4 Instance 2, Buffer Size: 0 [0001.718] tca9539_device_init: failed to write polar reg [0001.723] tca9539_init: failed to init device! [0001.727] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.742] I2C Bus Init done [0001.745] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.760] I2C Bus Init done [0001.763] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.778] I2C Bus Init done [0001.780] of_children_init: Ops found for compatible string maxim,max77620 [0001.796] max77620_init using irq 118 [0001.801] register 'maxim,max77620' pmic [0001.805] gpio_driver_register: register 'max77620-gpio' driver [0001.811] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.826] I2C Bus Init done [0001.831] NCK carveout not present [0001.835] shim_invoke: No NCT, Calling dts updates [0001.857] Find /i2c@7000c000's alias i2c0 [0001.860] get eeprom at 1-a2, size 256, type 0 [0001.865] get eeprom at 1-ae, size 256, type 0 [0001.880] Find /i2c@7000c400's alias i2c1 [0001.884] get eeprom at 2-a0, size 256, type 0 [0001.900] Find /i2c@7000c500's alias i2c2 [0001.904] get eeprom at 3-a0, size 256, type 0 [0001.908] get eeprom at 3-ae, size 256, type 0 [0001.920] Find /host1x/i2c@546c0000's alias i2c6 [0001.924] get eeprom at 7-a8, size 256, type 0 [0001.928] pm_ids_update: Updating 1,a2, size 256, type 0 [0001.934] I2C slave not started [0001.937] I2C write failed [0001.939] Writing offset failed [0001.942] eeprom_init: EEPROM read failed [0001.946] pm_ids_update: eeprom init failed [0001.950] pm_ids_update: Updating 1,ae, size 256, type 0 [0001.956] I2C slave not started [0001.959] I2C write failed [0001.961] Writing offset failed [0001.964] eeprom_init: EEPROM read failed [0001.968] pm_ids_update: eeprom init failed [0001.972] pm_ids_update: Updating 2,a0, size 256, type 0 [0001.978] I2C slave not started [0001.981] I2C write failed [0001.983] Writing offset failed [0001.986] eeprom_init: EEPROM read failed [0001.990] pm_ids_update: eeprom init failed [0001.994] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.025] pm_ids_update: The pm board id is 2180-1000-400 [0002.034] Adding plugin-manager/ids/2180-1000-400=/i2c@7000c500:module@0x50 [0002.044] pm_ids_update: pm id update successful [0002.048] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.078] pm_ids_update: The pm board id is 65535-65535-X [0002.086] Adding plugin-manager/ids/65535-65535-X=/i2c@7000c500:module@0x57 [0002.095] pm_ids_update: pm id update successful [0002.100] pm_ids_update: Updating 7,a8, size 256, type 0 [0002.107] GPIO driver for phandle 0xd6 could not be found [0002.112] I2C slave not started [0002.115] I2C write failed [0002.118] Writing offset failed [0002.121] eeprom_init: EEPROM read failed [0002.125] pm_ids_update: eeprom init failed [0002.131] GPIO driver for phandle 0xd6 could not be found [0002.164] updating /chosen/nvidia,wifi-mac node 00:04:4b:79:5c:5c [0002.173] updating /chosen/nvidia,bluetooth-mac node 00:04:4b:79:5c:5d [0002.182] updating /chosen/nvidia,ethernet-mac node 00:04:4b:79:5c:5e [0002.188] Plugin Manager: Parse ODM data 0x00084000 [0002.225] Find /i2c@7000c000's alias i2c0 [0002.229] get eeprom at 1-a2, size 256, type 0 [0002.233] get eeprom at 1-ae, size 256, type 0 [0002.249] Find /i2c@7000c400's alias i2c1 [0002.253] get eeprom at 2-a0, size 256, type 0 [0002.268] Find /i2c@7000c500's alias i2c2 [0002.272] get eeprom at 3-a0, size 256, type 0 [0002.277] get eeprom at 3-ae, size 256, type 0 [0002.288] Find /host1x/i2c@546c0000's alias i2c6 [0002.293] get eeprom at 7-a8, size 256, type 0 [0002.297] pm_ids_update: Updating 1,a2, size 256, type 0 [0002.302] I2C slave not started [0002.305] I2C write failed [0002.308] Writing offset failed [0002.311] eeprom_init: EEPROM read failed [0002.315] pm_ids_update: eeprom init failed [0002.319] pm_ids_update: Updating 1,ae, size 256, type 0 [0002.324] I2C slave not started [0002.327] I2C write failed [0002.330] Writing offset failed [0002.333] eeprom_init: EEPROM read failed [0002.337] pm_ids_update: eeprom init failed [0002.341] pm_ids_update: Updating 2,a0, size 256, type 0 [0002.346] I2C slave not started [0002.349] I2C write failed [0002.352] Writing offset failed [0002.355] eeprom_init: EEPROM read failed [0002.359] pm_ids_update: eeprom init failed [0002.363] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.393] pm_ids_update: The pm board id is 2180-1000-400 [0002.401] Adding plugin-manager/ids/2180-1000-400=/i2c@7000c500:module@0x50 [0002.408] pm_ids_update: pm id update successful [0002.412] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.443] pm_ids_update: The pm board id is 65535-65535-X [0002.450] Adding plugin-manager/ids/65535-65535-X=/i2c@7000c500:module@0x57 [0002.457] pm_ids_update: pm id update successful [0002.462] pm_ids_update: Updating 7,a8, size 256, type 0 [0002.469] GPIO driver for phandle 0xd6 could not be found [0002.474] I2C slave not started [0002.477] I2C write failed [0002.480] Writing offset failed [0002.483] eeprom_init: EEPROM read failed [0002.487] pm_ids_update: eeprom init failed [0002.493] GPIO driver for phandle 0xd6 could not be found [0002.526] Chip UID is 00000001642844421c000000120583c0 [0002.533] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 OS=l4t fbcon=map:0 net.ifnames=0 androidboot.modem=none androidboot.serialno=03245162101650c08305 androidboot.security=non-secure [0002.557] Add serial number:03245162101650c08305 as DT property [0002.565] calling apps_init() [0002.569] Found 18 GPT partitions in "sdmmc3_user" [0002.574] Proceeding to Cold Boot [0002.577] starting app android_boot_app [0002.581] Device state: unlocked [0002.584] display console init [0002.603] No valid panel node found [0002.612] enabling 'vdd-hdmi' regulator [0002.639] DT entry for leds-pwm not found [0002.643] hdmi cable not connected [0002.646] is_hdmi_needed: HDMI not connected, returning false [0002.652] set_instance_and_out_type: invalid out_type [0002.657] display_console_init: No display init [0002.667] Gpio keyboard init success [0002.671] bct_init bctinit [0002.673] device_query_partition_size: failed to open partition sdmmc3_user:BMP ! [0002.681] BMP partition read failed! [0002.684] blob_init: blob-partition BMP header read failed [0002.690] load_bmp_blob: BMP blob initialization failed [0002.695] Could not load/initialize BMP blob...ignoring [0002.700] bl_battery_charging: connected to external power supply [0002.711] display_console_ioctl: No display init [0002.716] switch_backlight failed [0002.719] bct_init bctinit [0002.722] device_query_partition_size: failed to open partition sdmmc3_user:MSC ! [0002.729] MSC Partition not found [0002.732] bct_init bctinit [0002.735] bct_init bctinit [0002.739] blob_init: USP partition does not have valid Blob [0002.744] Loading android kernel [0002.748] Default: NOT skip verified boot. [0002.752] Verified boot state = Orange [0002.758] display_console_clear: No display init [0002.763] kernel load address: 0x80080000, size: 503741 bytes [0002.769] ramdisk load address: 0x84100000, size: 0 bytes [0002.774] load kernel from storage [0002.778] decompressor handler not found [0002.789] Successfully loaded kernel and ramdisk images [0002.796] bct_init bctinit [0002.799] device_query_partition_size: failed to open partition sdmmc3_user:BMP ! [0002.807] BMP partition read failed! [0002.810] blob_init: blob-partition BMP header read failed [0002.815] load_bmp_blob: BMP blob initialization failed [0002.821] bmp blob is not loaded and initialized [0002.825] Failed to display boot-logo [0002.829] NCK carveout not present [0002.832] Skipping dts_overrides [0002.835] NCK carveout not present [0002.839] shim_invoke: No NCT, Calling dts updates [0002.860] Find /i2c@7000c000's alias i2c0 [0002.864] get eeprom at 1-a2, size 256, type 0 [0002.869] get eeprom at 1-ae, size 256, type 0 [0002.885] Find /i2c@7000c400's alias i2c1 [0002.889] get eeprom at 2-a0, size 256, type 0 [0002.905] Find /i2c@7000c500's alias i2c2 [0002.909] get eeprom at 3-a0, size 256, type 0 [0002.913] get eeprom at 3-ae, size 256, type 0 [0002.926] Find /host1x/i2c@546c0000's alias i2c6 [0002.930] get eeprom at 7-a8, size 256, type 0 [0002.935] pm_ids_update: Updating 1,a2, size 256, type 0 [0002.940] I2C slave not started [0002.943] I2C write failed [0002.946] Writing offset failed [0002.949] eeprom_init: EEPROM read failed [0002.953] pm_ids_update: eeprom init failed [0002.957] pm_ids_update: Updating 1,ae, size 256, type 0 [0002.962] I2C slave not started [0002.965] I2C write failed [0002.968] Writing offset failed [0002.971] eeprom_init: EEPROM read failed [0002.975] pm_ids_update: eeprom init failed [0002.979] pm_ids_update: Updating 2,a0, size 256, type 0 [0002.984] I2C slave not started [0002.987] I2C write failed [0002.990] Writing offset failed [0002.993] eeprom_init: EEPROM read failed [0002.997] pm_ids_update: eeprom init failed [0003.001] pm_ids_update: Updating 3,a0, size 256, type 0 [0003.031] pm_ids_update: The pm board id is 2180-1000-400 [0003.040] Adding plugin-manager/ids/2180-1000-400=/i2c@7000c500:module@0x50 [0003.050] pm_ids_update: pm id update successful [0003.055] pm_ids_update: Updating 3,ae, size 256, type 0 [0003.085] pm_ids_update: The pm board id is 65535-65535-X [0003.092] Adding plugin-manager/ids/65535-65535-X=/i2c@7000c500:module@0x57 [0003.101] pm_ids_update: pm id update successful [0003.106] pm_ids_update: Updating 7,a8, size 256, type 0 [0003.113] GPIO driver for phandle 0xd6 could not be found [0003.118] I2C slave not started [0003.121] I2C write failed [0003.124] Writing offset failed [0003.127] eeprom_init: EEPROM read failed [0003.131] pm_ids_update: eeprom init failed [0003.137] GPIO driver for phandle 0xd6 could not be found [0003.170] updating /chosen/nvidia,wifi-mac node 00:04:4b:79:5c:5c [0003.179] updating /chosen/nvidia,bluetooth-mac node 00:04:4b:79:5c:5d [0003.188] updating /chosen/nvidia,ethernet-mac node 00:04:4b:79:5c:5e [0003.195] Plugin Manager: Parse ODM data 0x00084000 [0003.216] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 OS=l4t fbcon=map:0 net.ifnames=0 androidboot.modem=none androidboot.serialno=03245162101650c08305 androidboot.security=non-secure [0003.240] Add serial number:03245162101650c08305 as DT property [0003.249] Updated bpmp info to DTB [0003.255] Updated initrd info to DTB [0003.259] "proc-board" doesn't exist, creating [0003.266] Updated board info to DTB [0003.269] "pmu-board" doesn't exist, creating [0003.277] Updated board info to DTB [0003.280] "display-board" doesn't exist, creating [0003.287] Updated board info to DTB [0003.290] "reset" doesn't exist, creating [0003.295] Updated reset info to DTB [0003.298] display_console_ioctl: No display init [0003.303] display_console_ioctl: No display init [0003.307] display_console_ioctl: No display init [0003.315] display_console_ioctl: No display init [0003.322] Cmdline: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 OS=l4t fbcon=map:0 net.ifnames=0 androidboot.modem=none androidboot.serialno=03245162101650c08305 androidboot.security=non-secure tegraid=21.1.2.0.0 ddr_die=2048M@2048M ddr_die=2048M@4096M section=256M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff2bf000 nvdumper_reserved=0xff23f000 core_edp_mv=1125 core_edp_ma=4000 gpt android.kerneltype=normal androidboot.touch_vendor_id=0 androidboot.touch_panel_id=63 androidboot.touch_feature=0 androidboot.bootloader=00.00.2014.50-t210-fadd1be5 androidboot.verifiedbootstate=orange [0003.395] Updated bootarg info to DTB [0003.402] Updated memory info to DTB [0003.411] set vdd_core voltage to 1125 mv [0003.415] setting 'vdd-core' regulator to 1125000 micro volts [0003.421] nvdumper Carveout: Base = 0xff23f000 and Size = 0x80000 [0003.427] bct_init bctinit [0003.430] Starting Bpmp FW [0003.433] BPMP-FW Carveout: Base = 0xff2c0000 and Size = 0x40000 U-Boot 2016.07-g0ce7ca2 (Jul 20 2017 - 00:37:03 -0700) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 4 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2 1 0 MMC: no card present switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 451 bytes read in 78 ms (4.9 KiB/s) p2371-2180 eMMC boot options 1: primary kernel 2: debug kernel Enter choice: 1 1: primary kernel Retrieving file: /boot/initrd 0 bytes read in 63 ms (0 Bytes/s) Retrieving file: /boot/Image 20984368 bytes read in 527 ms (38 MiB/s) append: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 OS=l4t fbcon=map:0 net.ifnames=0 androidboot.modem=none androidboot.serialno=03245162101650c08305 androidboot.security=non-secure tegraid=21.1.2.0.0 ddr_die=2048M@2048M ddr_die=2048M@4096M section=256M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff2bf000 nvdumper_reserved=0xff23f000 core_edp_mv=1125 core_edp_ma=4000 gpt android.kerneltype=normal androidboot.touch_vendor_id=0 androidboot.touch_panel_id=63 androidboot.touch_feature=0 androidboot.bootloader=00.00.2014.50-t210-fadd1be5 androidboot.verifiedbootstate=orange root=/dev/mmcblk0p1 rw rootwait ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 reserving fdt memory region: addr=80000000 size=20000 Using Device Tree in place at 0000000083100000, end 00000000831af7bf Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.38-tegra (buildbrain@mobile-u64-1576) (gcc version 4.8.5 (GCC) ) #1 SMP PREEMPT Thu Jul 20 00:41:06 PDT 2017 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] Reserved memory: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] Reserved memory: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] Reserved memory: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 16 MiB at 0x00000000fdc00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] PERCPU: Embedded 17 pages/cpu @ffffffc0ffe40000 s31360 r8192 d30080 u69632 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1027072 [ 0.000000] Kernel command line: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 OS=l4t fbcon=map:0 net.ifnames=0 androidboot.modem=none androidboot.serialno=03245162101650c08305 androidboot.security=non-secure tegraid=21.1.2.0.0 ddr_die=2048M@2048M ddr_die=2048M@4096M section=256M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff2bf000 nvdumper_reserved=0xff23f000 core_edp_mv=1125 core_edp_ma=4000 gpt android.kerneltype=normal androidboot.touch_vendor_id=0 androidboot.touch_panel_id=63 androidboot.touch_feature=0 androidboot.bootloader=00.00.2014.50-t210-fadd1be5 androidboot.verifiedbootstate=orange root=/dev/mmcblk0p1 rw rootwait [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3372564K/4173824K available (11009K kernel code, 1816K rwdata, 6352K rodata, 1208K init, 644K bss, 96748K reserved, 704512K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000 ( 246 GB) [ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum) [ 0.000000] 0xffffffbdc2000000 - 0xffffffbdc6000000 ( 64 MB actual) [ 0.000000] fixed : 0xffffffbffa7fd000 - 0xffffffbffac00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000 ( 16 MB) [ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc100000000 ( 4096 MB) [ 0.000000] .init : 0xffffffc001175000 - 0xffffffc0012a3000 ( 1208 KB) [ 0.000000] .text : 0xffffffc000080000 - 0xffffffc001174c04 ( 17364 KB) [ 0.000000] .data : 0xffffffc0012bd000 - 0xffffffc001483230 ( 1817 KB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] enable_t210_agic_clks:106 ape clocked & reset cleared [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] kmemleak: Kernel memory leak detector disabled [ 0.000000] Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.001693] Console: colour dummy device 80x25 [ 0.002561] console [tty0] enabled [ 0.002592] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.002628] pid_max: default: 32768 minimum: 301 [ 0.002717] Security Framework initialized [ 0.002738] SELinux: Initializing. [ 0.002849] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.002872] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.003545] Initializing cgroup subsys freezer [ 0.003576] Initializing cgroup subsys debug [ 0.003842] CPU0 ipc=1024 [ 0.003877] CPU1 ipc=1024 [ 0.003907] CPU2 ipc=1024 [ 0.003939] CPU3 ipc=1024 [ 0.004006] ASID allocator initialised with 65536 entries [ 0.027045] tegra-id: chipid=22117. [ 0.027075] tegra-id: opt_subrevision=0. [ 0.027106] Tegra Speedo/IDDQ fuse revision 4 [ 0.027125] Tegra: CPU Speedo ID 7, SoC Speedo ID 0, GPU Speedo ID 2 [ 0.027145] Tegra: CPU Process ID 0, SoC Process ID 0, GPU Process ID 0 [ 0.027166] Tegra: CPU Speedo Value 2026, SoC Speedo Value 1937, GPU Speedo Value 2040 [ 0.027194] Tegra: CPU IDDQ Value 2252, SoC IDDQ Value 2560, GPU IDDQ Value 3005 [ 0.027235] Tegra Revision: A02 SKU: 0x17 CPU Process: 0 SoC Process: 0 [ 0.028640] DTS File Name: /home/ubuntu/work3/modify28.1/kernel/kernel-4.4/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/jetson/kernel-dts/tegra210-jetson-cv-base-p2597-2180-a00.dts [ 0.028689] DTB Build time: Oct 3 2017 21:38:09 [ 0.044786] CPU1: Booted secondary processor [411fd071] [ 0.056756] CPU2: Booted secondary processor [411fd071] [ 0.068756] CPU3: Booted secondary processor [411fd071] [ 0.068842] Brought up 4 CPUs [ 0.068909] SMP: Total of 4 processors activated. [ 0.068933] CPU: All CPU(s) started at EL2 [ 0.068974] alternatives: patching kernel code [ 0.071407] devtmpfs: initialized [ 0.143642] Initilizing CustomIPI irq domain [ 0.143989] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.156945] pinctrl core: initialized pinctrl subsystem [ 0.157175] OS set in device tree is L4T. [ 0.157571] regulator-dummy: no parameters [ 0.157793] Initializing plugin-manager [ 0.157865] Plugin module not found [ 0.158832] node /plugin-manager/fragement@0 match with board >=2180-1000-300 [ 0.159631] node /plugin-manager/fragement@4 match with odm-data l4t [ 0.159752] Removing Prop nvidia,pmc-wakeup from target /bcmdhd_wlan [ 0.160285] Adding domain ape-pd to PM domain mc-clk-pd [ 0.160330] Adding domain adsp-pd to PM domain ape-pd [ 0.165233] NET: Registered protocol family 16 [ 0.181189] console [pstore-1] enabled [ 0.181212] pstore: Registered ramoops as persistent store backend [ 0.181236] ramoops: attached 0x200000@0xb0000000, ecc: 0/0 [ 0.192237] cpuidle: using governor ladder [ 0.204226] cpuidle: using governor menu [ 0.204590] bpmp: mail init ok [ 0.205717] vdso: 2 pages (1 code @ ffffffc0012c5000, 1 data @ ffffffc0012c4000) [ 0.205776] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.208127] atomic_pool_init():526: DMA: preallocated 1024 KiB pool for atomic allocations [ 0.209071] tegra_powergate_init: DONE [ 0.209112] DTS File Name: /home/ubuntu/work3/modify28.1/kernel/kernel-4.4/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/jetson/kernel-dts/tegra210-jetson-cv-base-p2597-2180-a00.dts [ 0.209162] DTB Build time: Oct 3 2017 21:38:09 [ 0.210182] Error: Driver 'tegra-mc' is already registered, aborting... [ 0.211847] platform tegra-carveouts: SMMU isn't ready yet [ 0.212618] platform tegra-carveouts: domain=ffffffc0fa12b318 allocates as[0]=ffffffc0fa1440a8 [ 0.212690] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver [ 0.212925] platform smmu_test: domain=ffffffc0fa12b618 allocates as[0]=ffffffc0fa144110 [ 0.213263] platform 70016000.bpmp: domain=ffffffc0fa12b918 allocates as[0]=ffffffc0fa144178 [ 0.213979] bpmp: ping status is 0 [ 0.214085] bpmp 70016000.bpmp: firmware tag is 1e4b302fc0f866f97885165cf8b395ac [ 0.214339] bpmp 70016000.bpmp: probe ok [ 0.215007] mc: mapped MMIO address: 0xffffff800007e000 -> 0x70019000 [ 0.215108] mc: mapped MMIO address: 0xffffff80000b6000 -> 0x7001c000 [ 0.215211] mc: mapped MMIO address: 0xffffff80000dc000 -> 0x7001d000 [ 0.215298] mc-err: Set intmask: 0x23d40 [ 0.227139] GPIO line 58 (wlan-default-input-h2) hogged as input [ 0.227188] GPIO line 65 (wlan-default-input-i1) hogged as input [ 0.227232] GPIO line 56 (wlan-default-output-high-h0) hogged as output/high [ 0.227273] GPIO line 64 (wlan-default-output-high-i0) hogged as output/high [ 0.227315] GPIO line 148 (cam0-rst) hogged as output/low [ 0.227360] GPIO line 151 (cam0-pwdn) hogged as output/low [ 0.227398] GPIO line 149 (cam1-rst) hogged as output/low [ 0.227436] GPIO line 152 (cam1-pwdn) hogged as output/low [ 0.227551] gpiochip_add_data: registered GPIOs 0 to 255 on device: tegra-gpio [ 0.230084] platform 70006000.serial: domain=ffffffc0fa1e6e18 allocates as[0]=ffffffc0fa1441e0 [ 0.231232] platform sound: domain=ffffffc0fa233718 allocates as[0]=ffffffc0fa144248 [ 0.233725] platform tegradc.0: domain=ffffffc0fa238918 allocates as[0]=ffffffc0fa1442b0 [ 0.234350] platform tegradc.0: IOVA linear map 0x00000000c6000000(2a000000) [ 0.234757] platform tegradc.1: domain=ffffffc0fa238c18 allocates as[0]=ffffffc0fa144318 [ 0.235383] platform tegradc.1: IOVA linear map 0x00000000c6000000(2a000000) [ 0.238406] platform 57000000.gpu: domain=ffffffc0fa246118 allocates as[0]=ffffffc0fa144380 [ 0.238484] platform 57000000.gpu: domain=ffffffc0fa246118 allocates as[1]=ffffffc0fa1443e8 [ 0.238558] platform 57000000.gpu: domain=ffffffc0fa246118 allocates as[2]=ffffffc0fa144450 [ 0.238626] platform 57000000.gpu: domain=ffffffc0fa246118 allocates as[3]=ffffffc0fa1444b8 [ 0.239409] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.239452] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present [ 0.239477] tegra-pmc: ### PMC reset source: Power on reset [ 0.239498] tegra-pmc: ### PMC reset status reg: 0x0 [ 0.239849] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [ 0.239882] tegra-pmc: Clear bootloader IO dpd settings [ 0.240342] tegra-pmc 7000e400.pmc: PMC: IO pad audio voltage is 1800000 [ 0.244320] tegra-pmc 7000e400.pmc: PMC: IO pad cam voltage is 1800000 [ 0.248318] tegra-pmc 7000e400.pmc: PMC: IO pad dbg voltage is 1800000 [ 0.252316] tegra-pmc 7000e400.pmc: PMC: IO pad dmic voltage is 1800000 [ 0.252345] tegra-pmc 7000e400.pmc: PMC: IO pad pex-ctrl voltage is 1800000 [ 0.256320] tegra-pmc 7000e400.pmc: PMC: IO pad spi voltage is 1800000 [ 0.260316] tegra-pmc 7000e400.pmc: PMC: IO pad uart voltage is 1800000 [ 0.264316] tegra-pmc 7000e400.pmc: PMC: IO pad audio-hv voltage is 1800000 [ 0.264344] tegra-pmc 7000e400.pmc: PMC: IO pad spi-hv voltage is 1800000 [ 0.268316] tegra-pmc 7000e400.pmc: PMC: IO pad gpio voltage is 1800000 [ 0.272317] tegra-pmc 7000e400.pmc: PMC: IO pad sdmmc3 voltage is 1800000 [ 0.272344] tegra-pmc 7000e400.pmc: IO padctrl driver initialized [ 0.272413] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands [ 0.275569] platform 1003000.pcie-controller: domain=ffffffc0fa24e218 allocates as[0]=ffffffc0fa144520 [ 0.277906] platform sdhci-tegra.3: domain=ffffffc0fa2e5318 allocates as[0]=ffffffc0fa144588 [ 0.278523] platform sdhci-tegra.0: domain=ffffffc0fa2e5718 allocates as[0]=ffffffc0fa1445f0 [ 0.284073] vdd-ac-bat: 5000 mV [ 0.285327] vdd-cpu-fixed: 1000 mV [ 0.289311] irq: no irq domain found for /soctherm@0x700E2000 ! [ 0.289655] irq: no irq domain found for /soctherm@0x700E2000 ! [ 0.313459] ACPI: Interpreter disabled. [ 0.314293] SCSI subsystem initialized [ 0.314599] usbcore: registered new interface driver usbfs [ 0.314670] usbcore: registered new interface driver hub [ 0.314779] usbcore: registered new device driver usb [ 0.318146] gpiochip_add_data: registered GPIOs 496 to 511 on device: tca9539 [ 0.319076] tegra-i2c 7000c400.i2c: no acknowledge from address 0x77 [ 0.319146] pca953x 1-0077: failed reading register [ 0.319228] pca953x: probe of 1-0077 failed with error -121 [ 0.321980] max77620 4-003c: PMIC Version OTP:0x3C and ES:0x8 [ 0.323755] GPIO line 490 (spmic-default-output-high) hogged as output/high [ 0.323874] gpiochip_add_data: registered GPIOs 488 to 495 on device: max77620-gpio [ 0.328395] vdd-core: 600 <--> 1400 mV at 1125 mV [ 0.332344] vddio-ddr: at 1125 mV [ 0.333180] vdd-pre-reg: 1350 mV [ 0.336220] vdd-1v8: 1800 mV [ 0.340221] avdd-sys: 1200 mV [ 0.344222] vdd-pex: 1050 mV [ 0.344833] vddio-sdmmc1: 1800 <--> 3300 mV at 3300 mV [ 0.345664] vdd-cam-hv: 2800 mV [ 0.348218] vdd-rtc: 850 mV [ 0.349076] avdd-ts-hv: 3300 mV [ 0.349926] vdd-ts: 1800 mV [ 0.352223] vdd-gen-pll-edp: 1050 mV [ 0.356221] vdd-hdmi-dp: 1050 mV [ 0.356859] max77620 4-003c: max77620 probe successful [ 0.358780] media: Linux media interface: v0.10 [ 0.358859] Linux video capture interface: v2.00 [ 0.366536] tegra210-emc 7001b000.memory-controller: validated EMC DFS table [ 0.366868] Advanced Linux Sound Architecture Driver Initialized. [ 0.370276] tegra210_dvfs: no clock found for sdmmc2_ddr [ 0.370328] tegra210_dvfs: no clock found for sdmmc4_ddr [ 0.370421] tegra210_dvfs: no clock found for sdmmc1_ddr [ 0.370461] tegra210_dvfs: no clock found for sdmmc3_ddr [ 0.373347] regulator_get() failed for (dvfs,vdd-cpu), -19 [ 0.373375] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe [ 0.376226] vdd-3v3: 3300 mV [ 0.380220] max77620-gpio7: 1050 mV [ 0.380540] lcd-bl-en: 1800 mV [ 0.380844] en-vdd-sd: 3300 mV [ 0.384220] vdd-sys-boost: 5000 mV [ 0.384895] vdd-hdmi: 5000 mV [ 0.385137] aux-3v3: 3300 mV [ 0.385389] snsr_pm: 3300 mV [ 0.388222] vdd-disp-3v0: 3000 mV [ 0.388889] vdd-fan: 5000 mV [ 0.389193] usb-vbus1: 5000 mV [ 0.389857] en-vdd-ts-1v8: 1800 mV [ 0.390510] en-vdd-ts-hv-3v3: 3300 mV [ 0.391359] en-vdd-disp-3v3: 3300 mV [ 0.392010] en-mdm-pwr-3v7: 3700 mV [ 0.392876] en-vdd-disp-1v8: 1800 mV [ 0.393528] en-vdd-cam-hv-2v8: 2800 mV [ 0.393814] rtl-5v0: 5000 mV [ 0.394122] en-usb-vbus2: 5000 mV [ 0.394531] en-vdd-vcm-2v8: 2800 mV [ 0.397274] extcon-gpio-states extcon:extcon@1: Cable state 1 [ 0.398646] clocksource: Switched to clocksource arch_sys_counter [ 0.437682] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.438068] dma_declare_coherent_resizable_cma_memory:290: resizable heap=vpr, base=0x00000000c6000000, size=0x2a000000 [ 0.438279] cma: enabled page replacement for spfn=c6000, epfn=f0000 [ 0.438307] dma_declare_coherent_resizable_cma_memory:337: resizable cma heap=vpr create successful [ 0.438339] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout [ 0.438400] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048 [ 0.438435] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout [ 0.438776] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB) [ 0.439496] misc nvmap: created heap vpr base 0x00000000c6000000 size (688128KiB) [ 0.440245] pnp: PnP ACPI: disabled [ 0.452120] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm [ 0.453957] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm [ 0.454367] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm [ 0.454565] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [ 0.456249] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type Tdiode_tegra [ 0.456509] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type PMIC-Die [ 0.456737] thermal thermal_zone6: Registering thermal zone thermal_zone6 for type Tboard_tegra [ 0.457926] isomgr_init(): iso emc max clk=1600000KHz [ 0.457949] isomgr_init(): max_iso_bw=11520000KB [ 0.458082] NET: Registered protocol family 2 [ 0.458704] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.458890] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.459164] TCP: Hash tables configured (established 32768 bind 32768) [ 0.459261] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.459323] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.459566] NET: Registered protocol family 1 [ 0.459874] RPC: Registered named UNIX socket transport module. [ 0.459902] RPC: Registered udp transport module. [ 0.459922] RPC: Registered tcp transport module. [ 0.459942] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.460187] Trying to unpack rootfs image as initramfs... [ 0.471377] host1x 50000000.host1x: initialized [ 0.473102] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.476374] futex hash table entries: 1024 (order: 5, 131072 bytes) [ 0.476496] audit: initializing netlink subsys (disabled) [ 0.476561] audit: type=2000 audit(0.471:1): initialized [ 0.488683] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.489185] fuse init (API version 7.23) [ 0.491923] io scheduler noop registered (default) [ 0.491955] io scheduler deadline registered [ 0.492288] io scheduler cfq registered [ 0.497409] tegra21x-padctl-uphy 7009f000.pinctrl: padctl mmio start 0x000000007009f000 end 0x000000007009ffff [ 0.497456] tegra21x-padctl-uphy 7009f000.pinctrl: TEGRA_FUSE_SKU_CALIB_0 0x920a411 [ 0.497490] tegra21x-padctl-uphy 7009f000.pinctrl: TEGRA_FUSE_USB_CALIB_EXT_0 0x4 [ 0.498971] tegra21x-padctl-uphy 7009f000.pinctrl: UTMI-0 is used by XUSB [ 0.499007] tegra21x-padctl-uphy 7009f000.pinctrl: using UTMI port 0 for otg [ 0.499037] tegra21x-padctl-uphy 7009f000.pinctrl: UTMI-2 is used by XUSB [ 0.499074] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 5, set usb3_lanes = 0x20 [ 0.499119] tegra21x-padctl-uphy 7009f000.pinctrl: USB3 port 1 maps to USB2 port 2 [ 0.499153] tegra21x-padctl-uphy 7009f000.pinctrl: UTMI-1 is used by XUSB [ 0.499187] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 6, set usb3_lanes = 0x60 [ 0.499228] tegra21x-padctl-uphy 7009f000.pinctrl: USB3 port 0 maps to USB2 port 1 [ 0.499273] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 1, set pcie_lanes = 0x2 [ 0.499320] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 2, set pcie_lanes = 0x6 [ 0.499365] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 3, set pcie_lanes = 0xe [ 0.499410] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 4, set pcie_lanes = 0x1e [ 0.499456] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 0, set pcie_lanes = 0x1f [ 0.499503] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 7, set sata_lanes = 0x80 [ 0.499937] tegra21x-padctl-uphy 7009f000.pinctrl: mailbox is not ready yet [ 0.500987] tegra-pwm 7000a000.pwm: PWM clk can sleep in ops [ 0.502082] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000 [ 0.502889] Adding domain pcie-pd to PM domain mc-clk-pd [ 0.507576] tegra-pcie 1003000.pcie-controller: 4x1, 1x1 configuration [ 0.507646] tegra-pcie 1003000.pcie-controller: failed to get PHY: -517 [ 0.507672] tegra-pcie 1003000.pcie-controller: failed to get PHYs: -517 [ 0.508850] regulator_get() failed for (1-002c,power), -19 [ 0.509016] tegra-i2c 7000c400.i2c: no acknowledge from address 0x2c [ 0.509088] lp855x 1-002c: failed to read 0x00 [ 0.509111] lp855x 1-002c: pre init device err: -121 [ 0.509133] lp855x 1-002c: device config err: -121 [ 0.509164] lp855x: probe of 1-002c failed with error -121 [ 0.511918] tsec 54500000.tsec: initialized [ 0.513236] tsec 54100000.tsecb: initialized [ 0.516105] nvdec 54480000.nvdec: initialized [ 0.521380] falcon 54340000.vic: initialized [ 0.523135] falcon 544c0000.nvenc: initialized [ 0.524284] falcon 54380000.nvjpg: initialized [ 0.526313] DC OR NODE connected to /host1x/sor [ 0.526432] display board info: id 0xffff, fab 0x0 [ 0.526494] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [ 0.526550] display board info: id 0xffff, fab 0x0 [ 0.526658] parse_dp_settings: No lt-data node. Using default setting. [ 0.526832] tegradc tegradc.0: DT parsed successfully [ 0.526892] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1020000, vi_iso_bw=750000, max_bw=1020000 [ 0.526897] tegradc tegradc.0: Display dc.ffffff8000980000 registered with id=0 [ 0.527224] display board info: id 0xffff, fab 0x0 [ 0.529213] tegradc tegradc.0: probed [ 0.531910] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.534030] tegra-adma 702e2000.adma: Tegra ADMA driver register 10 channels [ 0.535654] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized [ 0.535969] kfuse 7000fc00.kfuse: initialized [ 0.537889] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0 [ 0.538946] clk_cbus_round_rate: no gbus parent [ 0.538976] tegra_gpu_edp gpu_edp: unable to get max GPU freq [ 0.539532] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now [ 0.539566] vdd-cpu: 708 <--> 1322 mV at 708 mV [ 0.539628] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed [ 0.540859] vdd-gpu: applied init 1000000uV constraint [ 0.540890] vdd-gpu: 710 <--> 1320 mV at 1000 mV [ 0.540951] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed [ 0.541363] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.541501] No Device Node present for smmu client: serial8250 !! [ 0.541530] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 0.541566] No Device Node present for smmu client: serial8250 !! [ 0.541590] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 0.542704] No Device Node present for smmu client: serial8250 !! [ 0.542735] serial8250 serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 0.542784] No Device Node present for smmu client: serial8250 !! [ 0.542810] serial8250 serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 0.543518] console [ttyS0] disabled [ 0.543605] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 320, base_baud = 25500000) is a Tegra [ 2.612619] console [ttyS0] enabled [ 2.613966] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 321, base_baud = 0) is a TEGRA_UART [ 2.614421] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 322, base_baud = 0) is a TEGRA_UART [ 2.614798] serial-tegra 70006300.serial: RX in PIO mode [ 2.614897] 70006300.serial: ttyTHS3 at MMIO 0x70006300 (irq = 323, base_baud = 0) is a TEGRA_UART [ 2.616448] Console: switching to colour frame buffer device 80x30 [ 2.617282] gk20a 57000000.gpu: platform probe failed [ 2.687493] brd: module loaded [ 2.696822] tegradc tegradc.0: fb registered [ 2.697065] loop: module loaded [ 2.697689] zram: Added device: zram0 [ 2.697699] Silicon Labs C2 port support v. 0.51.0 - (C) 2007 Rodolfo Giometti [ 2.697925] nct1008_nct72 0-004c: find device tree node, parsing dt [ 2.697931] nct1008_nct72 0-004c: starting parse dt [ 2.698009] nct1008_nct72 0-004c: success parsing dt [ 2.698258] nct1008_nct72 0-004c: success in enabling tmp451 VDD rail [ 2.791859] tmp451: Enabled overheat logging at 102.00C [ 2.803382] nct1008_nct72 0-004c: nct1008_probe: initialized [ 2.814044] THERMAL EST: found 2 subdevs [ 2.820072] THERMAL EST num_resources: 0 [ 2.826011] [THERMAL EST subdev 0] [ 2.831410] [THERMAL EST subdev 1] [ 2.837071] thermal thermal_zone7: Registering thermal zone thermal_zone7 for type thermal-fan-est [ 2.849840] THERMAL EST: thz register success. [ 2.860314] THERMAL EST: end of probe, return err: 0 [ 2.867221] tegra_profiler: Branch: Dev [ 2.872857] tegra_profiler: Version: 1.109 [ 2.878667] tegra_profiler: Samples version: 37 [ 2.884855] tegra_profiler: IO version: 21 [ 2.890561] armv8_pmu: imp: 0x41, idcode: 0x1 [ 2.896517] armv8_pmu: [0] arch: AA64 PmuV3 ARM CORTEX-A57, type: 5, ver: 0 [ 2.905143] armv8_pmu: imp: 0x41, idcode: 0x1 [ 2.911153] armv8_pmu: [1] arch: AA64 PmuV3 ARM CORTEX-A57, type: 5, ver: 0 [ 2.919849] armv8_pmu: imp: 0x41, idcode: 0x1 [ 2.925885] armv8_pmu: [2] arch: AA64 PmuV3 ARM CORTEX-A57, type: 5, ver: 0 [ 2.934544] armv8_pmu: imp: 0x41, idcode: 0x1 [ 2.940545] armv8_pmu: [3] arch: AA64 PmuV3 ARM CORTEX-A57, type: 5, ver: 0 [ 2.949430] tegra_profiler: auth: init [ 2.955440] tegra-ahci 70027000.sata: Missing devslp-active state [ 2.964269] Rounding down aligned max_sectors from 4294967295 to 4294967288 [ 2.973583] spi-tegra114 7000d400.spi: Static pin configuration used [ 2.982575] spi-tegra114 7000da00.spi: Static pin configuration used [ 2.992123] tun: Universal TUN/TAP device driver, 1.6 [ 2.996975] tegradc tegradc.0: nominal-pclk:25200000 parent:25800000 div:1.5 pclk:17200000 24948000~27468000 [ 2.996981] tegradc tegradc.0: pclk out of range! [ 2.996988] tegradc tegradc.0: tegra_dc_init: tegra_dc_program_mode failed [ 3.027884] tun: (C) 1999-2004 Max Krasnyansky [ 3.036407] PPP generic driver version 2.4.2 [ 3.042798] PPP BSD Compression module registered [ 3.049430] PPP Deflate Compression module registered [ 3.056455] PPP MPPE Compression module registered [ 3.063243] NET: Registered protocol family 24 [ 3.069768] usbcore: registered new interface driver r8152 [ 3.077348] usbcore: registered new interface driver asix [ 3.084765] usbcore: registered new interface driver ax88179_178a [ 3.092836] usbcore: registered new interface driver cdc_ether [ 3.100595] usbcore: registered new interface driver smsc95xx [ 3.108197] usbcore: registered new interface driver net1080 [ 3.115648] usbcore: registered new interface driver cdc_subset [ 3.123305] usbcore: registered new interface driver zaurus [ 3.130590] usbcore: registered new interface driver cdc_ncm [ 3.137944] usbcore: registered new interface driver usb-storage [ 3.145556] usbcore: registered new interface driver usbserial [ 3.152863] usbcore: registered new interface driver ftdi_sio [ 3.159998] usbserial: USB Serial support registered for FTDI USB Serial Device [ 3.170146] usbcore: registered new interface driver option [ 3.177184] usbserial: USB Serial support registered for GSM modem (1-port) [ 3.185622] usbcore: registered new interface driver pl2303 [ 3.192656] usbserial: USB Serial support registered for pl2303 [ 3.201083] tegra-xudc-new 700d0000.xudc: usb2 phy is not available yet [ 3.341134] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc1 [ 3.353695] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc0 [ 3.362455] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 3.370702] i2c /dev entries driver [ 3.377716] IR NEC protocol handler initialized [ 3.383817] IR Sharp protocol handler initialized [ 3.390116] IR XMP protocol handler initialized [ 3.396345] usbcore: registered new interface driver uvcvideo [ 3.403778] USB Video Class driver (1.1.1) [ 3.409868] max77620-power max77620-power: Event recorder REG_NVERC : 0x0 [ 3.420534] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2 [ 3.429526] tegra_soctherm 700e2000.soctherm: pllx_offset tz:1 max:8, min:4 [ 3.438946] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC [ 3.451806] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC [ 3.465148] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.478861] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC [ 3.492281] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC [ 3.505967] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.519915] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature 2147483647 forced to 127000 [ 3.533705] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC [ 3.547611] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature [ 3.550669] tegradc tegradc.0: _tegra_dc_controller_enable: tegra_dc_init failed [ 3.551056] DC OR NODE connected to /host1x/sor1 [ 3.551301] tegradc tegradc.1: DT parsed successfully [ 3.551349] tegradc tegradc.1: Display dc.ffffff8007400000 registered with id=1 [ 3.554332] tegra-i2c 7000c700.i2c: no acknowledge from address 0x50 [ 3.555584] tegradc tegradc.1: probed [ 3.616244] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19 [ 3.627794] tegra_aotag tegra-aotag: Registering sensor 0 [ 3.635903] tegra_aotag tegra-aotag: Bound to TZ : ID 0 [ 3.643664] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0 [ 3.651731] tegradc tegradc.1: fb registered [ 3.652650] FAN dev name: pwm-fan [ 3.652695] FAN:gpio request success. [ 3.652760] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255 [ 3.653068] pwm_fan_driver pwm-fan: unable to request PWM, trying legacy API [ 3.653076] pwm_fan_driver pwm-fan: got pwm for fan [ 3.664266] pwm_fan_driver pwm-fan: fan tach request irq success [ 3.664276] pwm_fan_driver pwm-fan: tach period: 1000 [ 3.664386] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2 [ 3.664394] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2 [ 3.664401] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2 [ 3.664408] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2 [ 3.664414] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3 [ 3.664421] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3 [ 3.664427] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3 [ 3.664434] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4 [ 3.664441] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4 [ 3.664447] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4 [ 3.665523] tegra-wdt 60005100.watchdog: Tegra WDT enabled on probe. Timeout = 120 seconds. [ 3.665845] tegra-wdt 60005100.watchdog: initialized (timeout = 120 sec, nowayout = 1) [ 3.666180] device-mapper: uevent: version 1.0.3 [ 3.666501] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com [ 3.669874] sdhci: Secure Digital Host Controller Interface driver [ 3.669877] sdhci: Copyright(c) Pierre Ossman [ 3.669886] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.671421] sdhci-tegra sdhci-tegra.3: Parent select= pll_p rate=408000000 [ 3.671728] sdhci-tegra sdhci-tegra.3: Parent select= pll_c4_out2 rate=199680000 [ 3.671753] sdhci-tegra sdhci-tegra.3: Client registration for eMC Successful [ 3.676595] tegra-se 70012000.se: tegra_se_probe: complete [ 3.677366] hidraw: raw HID events driver (C) Jiri Kosina [ 3.680397] usbcore: registered new interface driver usbhid [ 3.680400] usbhid: USB HID core driver [ 3.682633] tegra-i2c 7000c400.i2c: no acknowledge from address 0x42 [ 3.682707] ina3221x 1-0042: ina3221 reset failure status: 0xffffff87 [ 3.683109] ina3221x: probe of 1-0042 failed with error -121 [ 3.683909] tegra-i2c 7000c400.i2c: no acknowledge from address 0x43 [ 3.683958] ina3221x 1-0043: ina3221 reset failure status: 0xffffff87 [ 3.684333] ina3221x: probe of 1-0043 failed with error -121 [ 3.685020] parse_throttle_dt_data: Num cap clks = 6 [ 3.685026] parse_throttle_dt_data: clk=cclk_g type=2 [ 3.685037] parse_throttle_dt_data: clk=gpu type=4 [ 3.685081] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0 [ 3.685116] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0 [ 3.685157] parse_throttle_dt_data: clk=cap.throttle.sclk type=0 [ 3.685161] parse_throttle_dt_data: clk=emc type=3 [ 3.685956] tegra_throttle_probe: probe successful. #cdevs=4 [ 3.686232] tegra21x_actmon 6000c800.actmon: in actmon_register()... [ 3.687328] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all [ 3.688848] tegra124-dfll 70110000.clock: config PMU interface as PWM [ 3.694932] No Device Node present for smmu client: snd-soc-dummy !! [ 3.694941] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 3.694950] No Device Node present for smmu client: snd-soc-dummy !! [ 3.694955] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 3.695183] No Device Node present for smmu client: snd-soc-dummy !! [ 3.695189] snd-soc-dummy snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 3.695218] No Device Node present for smmu client: snd-soc-dummy !! [ 3.695224] snd-soc-dummy snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 3.700956] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input0 [ 3.710831] mmc0: SDHCI controller on sdhci-tegra.3 [sdhci-tegra.3] using ADMA 64-bit with 64 bit addr [ 3.711226] sdhci-tegra sdhci-tegra.1: Parent select= pll_p rate=408000000 [ 3.711247] sdhci-tegra sdhci-tegra.1: Client registration for eMC Successful [ 3.721012] tegra210-i2s tegra210-i2s.0: Missing prop fsync-width for I2S0 [ 3.722774] tegra210-i2s tegra210-i2s.2: Missing prop fsync-width for I2S2 [ 3.723378] tegra210-i2s tegra210-i2s.3: Missing prop fsync-width for I2S3 [ 3.724091] tegra210-i2s tegra210-i2s.4: Missing prop fsync-width for I2S4 [ 3.736693] OPE platform probe [ 3.736885] OPE platform probe successful [ 3.737270] OPE platform probe [ 3.737452] OPE platform probe successful [ 3.739403] tegra-snd-t210ref-mobile-rt565x sound: Failed to get HP Det GPIO, should be handled by codec [ 3.750744] mmc1: SDHCI controller on sdhci-tegra.1 [sdhci-tegra.1] using ADMA 64-bit with 64 bit addr [ 3.751503] sdhci-tegra sdhci-tegra.0: Got CD GPIO [ 3.751554] sdhci-tegra sdhci-tegra.0: Got WP GPIO [ 3.751634] sdhci-tegra sdhci-tegra.0: Parent select= pll_p rate=408000000 [ 3.751692] sdhci-tegra sdhci-tegra.0: wakeup init done, cd_irq: 262 [ 3.751714] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful [ 3.753671] en-vdd-sd: supplied by vdd-3v3 [ 3.774546] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF1 <-> ADMAIF1 mapping ok [ 3.774805] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF2 <-> ADMAIF2 mapping ok [ 3.775033] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF3 <-> ADMAIF3 mapping ok [ 3.775264] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF4 <-> ADMAIF4 mapping ok [ 3.775496] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF5 <-> ADMAIF5 mapping ok [ 3.775725] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF6 <-> ADMAIF6 mapping ok [ 3.775946] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF7 <-> ADMAIF7 mapping ok [ 3.776168] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF8 <-> ADMAIF8 mapping ok [ 3.776406] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF9 <-> ADMAIF9 mapping ok [ 3.776633] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF10 <-> ADMAIF10 mapping ok [ 3.781362] mmc0: MAN_BKOPS_EN bit is not set [ 3.788350] mmc0: Skipping tuning since strobe enabled [ 3.794166] mmc0: new HS400 MMC card at address 0001 [ 3.794718] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 3.794928] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB [ 3.796252] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 [ 3.802867] mmc2: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA 64-bit with 64 bit addr [ 3.805037] input: tegra-snd-t210ref-mobile-rt565x Headphone Jack as /devices/sound/sound/card1/input1 [ 3.805568] tegra-snd-t210ref-mobile-rt565x sound: codec-dai "dit-hifi" registered [ 3.805573] tegra-snd-t210ref-mobile-rt565x sound: This is a dummy codec [ 3.806295] GACT probability NOT on [ 3.806306] Mirror/redirect action on [ 3.806321] u32 classifier [ 3.806323] Actions configured [ 3.806334] Netfilter messages via NETLINK v0.30. [ 3.806382] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 3.806828] ctnetlink v0.93: registering with nfnetlink. [ 3.807493] xt_time: kernel timezone is -0000 [ 3.807640] ipip: IPv4 over IPv4 tunneling driver [ 3.808276] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.808409] arp_tables: (C) 2002 David S. Miller [ 3.808478] Initializing XFRM netlink socket [ 3.809298] NET: Registered protocol family 10 [ 3.810260] mip6: Mobile IPv6 [ 3.810287] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 3.810478] sit: IPv6 over IPv4 tunneling driver [ 3.811575] NET: Registered protocol family 17 [ 3.811602] NET: Registered protocol family 15 [ 3.811638] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 3.811668] Key type dns_resolver registered [ 3.817394] Registered cp15_barrier emulation handler [ 3.843783] mmc1: queuing unknown CIS tuple 0x80 (5 bytes) [ 4.045678] mmc1 tuning done saved tap delay=49 [ 4.045681] mmc1: hw tuning done ... [ 4.045688] mmc1: tuning_window[0]: 0x9fffffff [ 4.045693] mmc1: tuning_window[1]: 0xffffffff [ 4.045699] mmc1: tuning_window[2]: 0xffffff9f [ 4.045703] mmc1: tuning_window[3]: 0x7fff8fff [ 4.045708] mmc1: tuning_window[4]: 0x0 [ 4.045713] mmc1: tuning_window[5]: 0x0 [ 4.045718] mmc1: tuning_window[6]: 0x0 [ 4.045723] mmc1: tuning_window[7]: 0x0 [ 4.045727] sdhci: Tap value: 49 | Trim value: 8 [ 4.045730] sdhci: SDMMC_VENDOR_INTR_STATUS[0x108]: 0x40000 [ 4.051151] mmc1: queuing unknown CIS tuple 0x91 (3 bytes) [ 4.051198] mmc1: new ultra high speed SDR104 SDIO card at address 0001 [ 4.828277] isp 54600000.isp: initialized [ 4.835387] isp 54680000.isp: initialized [ 4.844754] clk_cbus_recalc_rate: no gbus parent [ 4.850734] clk_cbus_round_rate: no gbus parent [ 4.856585] clk_cbus_round_rate: no gbus parent [ 4.862466] clk_cbus_recalc_rate: no gbus parent [ 4.869026] clk_cbus_recalc_rate: no gbus parent [ 4.874796] clk_cbus_round_rate: no gbus parent [ 4.880417] clk_cbus_round_rate: no gbus parent [ 4.885985] clk_cbus_recalc_rate: no gbus parent [ 4.891630] tegra_dvfs: GPU-cap: registered [ 4.896889] tegra dvfs: vdd-cpu: nominal 1226mV, offset 708000uV, step 19200uV, scaling enabled [ 4.907679] tegra dvfs: vdd-core: nominal 1125mV, offset 600000uV, step 12500uV, scaling enabled [ 4.918930] tegra dvfs: vdd-gpu: nominal 1110mV, offset 710000uV, step 10000uV, scaling enabled [ 4.933547] tegra_dvfs: vdd-gpu-vts: registered [ 4.942183] xhci-tegra 70090000.xusb: can't get usb3-0 phy (-517) [ 4.950593] tegra21x-padctl-uphy 7009f000.pinctrl: padctl mmio start 0x000000007009f000 end 0x000000007009ffff [ 4.964140] tegra21x-padctl-uphy 7009f000.pinctrl: TEGRA_FUSE_SKU_CALIB_0 0x920a411 [ 4.975500] tegra21x-padctl-uphy 7009f000.pinctrl: TEGRA_FUSE_USB_CALIB_EXT_0 0x4 [ 4.988190] tegra21x-padctl-uphy 7009f000.pinctrl: UTMI-0 is used by XUSB [ 4.997100] tegra21x-padctl-uphy 7009f000.pinctrl: using UTMI port 0 for otg [ 5.006242] tegra21x-padctl-uphy 7009f000.pinctrl: UTMI-2 is used by XUSB [ 5.015108] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 5, set usb3_lanes = 0x20 [ 5.027281] tegra21x-padctl-uphy 7009f000.pinctrl: USB3 port 1 maps to USB2 port 2 [ 5.039341] tegra21x-padctl-uphy 7009f000.pinctrl: UTMI-1 is used by XUSB [ 5.048575] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 6, set usb3_lanes = 0x60 [ 5.061396] tegra21x-padctl-uphy 7009f000.pinctrl: USB3 port 0 maps to USB2 port 1 [ 5.073923] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 1, set pcie_lanes = 0x2 [ 5.086789] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 2, set pcie_lanes = 0x6 [ 5.099646] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 3, set pcie_lanes = 0xe [ 5.112612] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 4, set pcie_lanes = 0x1e [ 5.125718] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 0, set pcie_lanes = 0x1f [ 5.138818] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 7, set sata_lanes = 0x80 [ 5.152625] usb-vbus1: supplied by vdd-3v3 [ 5.161664] tegra21x-padctl-uphy 7009f000.pinctrl: Done tegra21x_padctl_uphy_probe [ 5.177168] tegra-pcie 1003000.pcie-controller: 4x1, 1x1 configuration [ 5.186683] tegra-pcie 1003000.pcie-controller: PCIE: Enable power rails [ 5.196507] clk_cbus_round_rate: no gbus parent [ 5.203645] tegra_gpu_edp gpu_edp: unable to get max GPU freq [ 5.212587] tegra-ahci 70027000.sata: Missing devslp-active state [ 5.214234] gk20a 57000000.gpu: GPCPLL initial settings: NA mode, M=1, N=34, P=3 [ 5.224902] tegra-pcie 1003000.pcie-controller: probing port 0, using 4 lanes [ 5.227016] tegra-pcie 1003000.pcie-controller: probing port 1, using 1 lanes [ 5.254214] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 5.268166] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pmp pio slum part deso sadm apst [ 5.287699] scsi host0: tegra_ahci [ 5.298198] scsi host1: tegra_ahci [ 5.304129] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 372 [ 5.316657] ata2: DUMMY [ 5.324411] tegra-xudc-new 700d0000.xudc: USB charger detection disabled [ 5.333458] tegra-xudc-new 700d0000.xudc: device mode on [ 5.342705] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered [ 5.357691] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered [ 5.371294] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered [ 5.384407] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered [ 5.400375] xhci-tegra 70090000.xusb: UTMI port 0 has OTG_CAP [ 5.407058] xhci-tegra 70090000.xusb: No USB3 port has OTG_CAP [ 5.416979] xhci-tegra 70090000.xusb: Direct firmware load for tegra21x_xusb_firmware failed with error -2 [ 5.428298] xhci-tegra 70090000.xusb: Falling back to user helper [ 5.431451] input: gpio-keys as /devices/gpio-keys/input/input2 [ 5.464954] tegra_rtc 7000e000.rtc: setting system clock to 2017-10-04 03:00:25 UTC (1507086025) [ 5.476560] vi 54080000.vi: vi_probe: ++ [ 5.489231] vi 54080000.vi: initialized [ 5.500591] vi 54080000.vi: all channel register failed [ 5.507621] Disable partitions left on by BL [ 5.512774] disb [ 5.525288] DRAM derating cdev registered. [ 5.531026] vdd-cpu-fixed: disabling [ 5.535458] vdd-cam-hv: disabling [ 5.539685] avdd-ts-hv: disabling [ 5.543869] vdd-ts: disabling [ 5.547675] max77620-gpio7: disabling [ 5.552368] lcd-bl-en: disabling [ 5.556235] en-vdd-sd: disabling [ 5.560144] aux-3v3: disabling [ 5.563845] snsr_pm: disabling [ 5.567511] vdd-disp-3v0: disabling [ 5.571585] vdd-fan: disabling [ 5.575199] usb-vbus1: disabling [ 5.578988] en-vdd-ts-1v8: disabling [ 5.583116] en-vdd-ts-hv-3v3: disabling [ 5.587473] en-vdd-disp-3v3: disabling [ 5.591720] en-mdm-pwr-3v7: disabling [ 5.599311] en-vdd-disp-1v8: disabling [ 5.603519] en-vdd-cam-hv-2v8: disabling [ 5.607873] rtl-5v0: disabling [ 5.611346] en-usb-vbus2: disabling [ 5.615260] en-vdd-vcm-2v8: disabling [ 5.620690] ALSA device list: [ 5.624052] #0: tegra-hda at 0x70038000 irq 350 [ 5.629180] #1: tegra-snd-t210ref-mobile-rt565x [ 5.642848] ata1: SATA link down (SStatus 0 SControl 300) [ 5.649917] EXT4-fs (mmcblk0p1): couldn't mount as ext3 due to feature incompatibilities [ 5.659957] EXT4-fs (mmcblk0p1): couldn't mount as ext2 due to feature incompatibilities [ 5.662681] tegra-pcie 1003000.pcie-controller: link 0 down, retrying [ 5.760867] EXT4-fs (mmcblk0p1): 7 orphan inodes deleted [ 5.766783] EXT4-fs (mmcblk0p1): recovery complete [ 5.781941] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 5.791234] VFS: Mounted root (ext4 filesystem) on device 179:1. [ 5.804658] devtmpfs: mounted [ 5.808585] Freeing unused kernel memory: 1208K (ffffffc001175000 - ffffffc0012a3000) [ 5.817868] Freeing alternatives memory: 76K (ffffffc0012a3000 - ffffffc0012b6000) [ 5.901197] random: systemd: uninitialized urandom read (16 bytes read, 66 bits of entropy available) [ 5.914026] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 5.935172] systemd[1]: Detected architecture arm64. [ 5.947777] systemd[1]: Set hostname to . [ 5.964866] random: systemd: uninitialized urandom read (16 bytes read, 67 bits of entropy available) [ 5.967697] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 67 bits of entropy available) [ 5.967768] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 67 bits of entropy available) [ 5.967789] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 67 bits of entropy available) [ 5.967906] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 67 bits of entropy available) [ 5.969291] random: systemd-sysv-ge: uninitialized urandom read (16 bytes read, 67 bits of entropy available) [ 5.975386] random: systemd-sysv-ge: uninitialized urandom read (16 bytes read, 68 bits of entropy available) [ 5.992266] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 70 bits of entropy available) [ 5.992380] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 70 bits of entropy available) [ 6.104852] tegra-pcie 1003000.pcie-controller: link 0 down, retrying [ 6.196448] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 6.207553] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ 6.216960] systemd[1]: Listening on Journal Socket (/dev/log). [ 6.225322] systemd[1]: Created slice System Slice. [ 6.232551] systemd[1]: Reached target Encrypted Volumes. [ 6.240201] systemd[1]: Reached target Swap. [ 6.246747] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 6.255242] systemd[1]: Created slice system-getty.slice. [ 6.262793] systemd[1]: Listening on udev Kernel Socket. [ 6.270168] systemd[1]: Reached target User and Group Name Lookups. [ 6.278530] systemd[1]: Listening on udev Control Socket. [ 6.285976] systemd[1]: Listening on Device-mapper event daemon FIFOs. [ 6.294625] systemd[1]: Listening on Journal Audit Socket. [ 6.302081] systemd[1]: Reached target Remote File Systems (Pre). [ 6.310124] systemd[1]: Reached target Remote File Systems. [ 6.317666] systemd[1]: Listening on LVM2 poll daemon socket. [ 6.325454] systemd[1]: Listening on Journal Socket. [ 6.332969] systemd[1]: Started Braille Device Support. [ 6.345036] systemd[1]: Mounting Debug File System... [ 6.353018] systemd[1]: Starting Create list of required static device nodes for the current kernel... [ 6.365377] systemd[1]: Listening on Syslog Socket. [ 6.373067] systemd[1]: Starting Journal Service... [ 6.380033] systemd[1]: Listening on LVM2 metadata daemon socket. [ 6.388972] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling... [ 6.402349] systemd[1]: Created slice User and Session Slice. [ 6.410238] systemd[1]: Reached target Slices. [ 6.417359] systemd[1]: Starting Remount Root and Kernel File Systems... [ 6.433627] systemd[1]: Starting Load Kernel Modules... [ 6.443338] systemd[1]: Mounted Debug File System. [ 6.451756] systemd[1]: Started Create list of required static device nodes for the current kernel. [ 6.465091] systemd[1]: Started Remount Root and Kernel File Systems. [ 6.474929] systemd[1]: Started Load Kernel Modules. [ 6.497311] systemd[1]: Started LVM2 metadata daemon. [ 6.505288] systemd[1]: Mounting FUSE Control File System... [ 6.513723] systemd[1]: Mounting Configuration File System... [ 6.522200] systemd[1]: Starting Apply Kernel Variables... [ 6.530450] systemd[1]: Starting Load/Save Random Seed... [ 6.539361] systemd[1]: Starting udev Coldplug all Devices... [ 6.547908] systemd[1]: Starting Create Static Device Nodes in /dev... [ 6.557658] systemd[1]: Mounted Configuration File System. [ 6.565433] systemd[1]: Mounted FUSE Control File System. [ 6.572985] systemd[1]: Started Journal Service. [ 6.610667] tegra-pcie 1003000.pcie-controller: link 0 down, retrying [ 6.618000] systemd-journald[217]: Received request to flush runtime journal from PID 1 [ 6.629718] tegra-pcie 1003000.pcie-controller: link 0 down, ignoring [ 6.822211] xhci-tegra 70090000.xusb: cannot find firmware....retry after 1 second [ 6.864290] regulator_get() failed for (backlight,power), -19 [ 6.906376] cfg80211: World regulatory domain updated: [ 6.914977] cfg80211: DFS Master region: unset [ 6.920393] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 6.934180] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 6.944887] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 6.954693] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 6.964641] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 6.976005] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 6.987427] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 6.997517] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 7.010950] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 7.040464] dhd_module_init in [ 7.066678] tegra-pcie 1003000.pcie-controller: link 1 down, retrying [ 7.074260] found wifi platform device bcmdhd_wlan [ 7.084634] Power-up adapter 'DHD generic adapter' [ 7.106305] wifi_platform_set_power = 1 [ 7.217929] random: nonblocking pool is initialized [ 7.306679] wifi_platform_bus_enumerate device present 1 [ 7.323104] wifi_platform_bus_enumerate device present 0 [ 7.331149] F1 signature read @0x18000000=0x17214354 [ 7.343025] F1 signature OK, socitype:0x1 chip:0x4354 rev:0x1 pkg:0x2 [ 7.351514] DHD: dongle ram size is set to 786432(orig 786432) at 0x180000 [ 7.362760] wifi_platform_prealloc: failed to alloc static mem section 7 [ 7.374017] wifi_platform_get_mac_addr [ 7.380660] CFG80211-ERROR) wl_setup_wiphy : Registering Vendor80211 [ 7.386026] wl_create_event_handler(): thread:wl_event_handler:1cd started [ 7.386032] CFG80211-ERROR) wl_event_handler : tsk Enter, tsk = 0xffffffc07ae81a70 [ 7.386661] dhd_attach(): thread:dhd_watchdog_thread:1ce started [ 7.386708] dhd_attach(): thread:dhd_dpc:1cf started [ 7.386743] dhd_attach(): thread:dhd_rxf:1d0 started [ 7.386748] dhd_deferred_work_init: work queue initialized [ 7.386926] Dongle Host Driver, version 1.201.82 (r) [ 7.386926] Compiled in drivers/net/wireless/bcmdhd on Jul 20 2017 at 00:39:01 [ 7.387268] tegra_sysfs_register [ 7.387317] Register interface [wlan0] MAC: 00:04:4b:79:5c:5c [ 7.387317] [ 7.387320] dhd_prot_ioctl : bus is down. we have nothing to do [ 7.387401] sdhci-tegra sdhci-tegra.1: Tuning already done, restoring the best tap value : 49 [ 7.388460] wifi_platform_set_power = 0 [ 7.484736] tegra-pcie 1003000.pcie-controller: link 1 down, retrying [ 7.831831] xhci-tegra 70090000.xusb: Firmware timestamp: 2016-11-24 02:31:08 UTC, Version: 50.18 release [ 7.853088] xhci-tegra 70090000.xusb: xHCI Host Controller [ 7.865108] xhci-tegra 70090000.xusb: new USB bus registered, assigned bus number 1 [ 7.879028] xhci-tegra 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010810 [ 7.890769] tegra-pcie 1003000.pcie-controller: link 1 down, retrying [ 7.891664] xhci-tegra 70090000.xusb: irq 319, io mem 0x70090000 [ 7.891778] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 7.891781] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.891783] usb usb1: Product: xHCI Host Controller [ 7.891785] usb usb1: Manufacturer: Linux 4.4.38-tegra xhci-hcd [ 7.891787] usb usb1: SerialNumber: 70090000.xusb [ 7.894357] hub 1-0:1.0: USB hub found [ 7.894384] hub 1-0:1.0: 5 ports detected [ 7.914895] xhci-tegra 70090000.xusb: xHCI Host Controller [ 7.914909] xhci-tegra 70090000.xusb: new USB bus registered, assigned bus number 2 [ 7.915058] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 7.915061] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.915064] usb usb2: Product: xHCI Host Controller [ 7.915066] usb usb2: Manufacturer: Linux 4.4.38-tegra xhci-hcd [ 7.915068] usb usb2: SerialNumber: 70090000.xusb [ 7.915602] hub 2-0:1.0: USB hub found [ 7.915741] hub 2-0:1.0: 4 ports detected [ 8.014665] tegra-pcie 1003000.pcie-controller: link 1 down, ignoring [ 8.022237] tegra-pcie 1003000.pcie-controller: PCIE: no end points detected [ 8.031426] tegra-pcie 1003000.pcie-controller: PCIE: Disable power rails [ 8.081892] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 8.203409] usb 1-3: new high-speed USB device number 2 using xhci-tegra [ 8.231286] usb 2-1: new SuperSpeed USB device number 2 using xhci-tegra [ 8.239244] usb 1-3: New USB device found, idVendor=0424, idProduct=2134 [ 8.247029] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 8.255154] usb 1-3: Product: USB2134B [ 8.261412] usb 1-3: Manufacturer: SMSC [ 8.267669] xhci-tegra 70090000.xusb: tegra_xhci_mbox_work mailbox command 6 [ 8.276147] usb 2-1: New USB device found, idVendor=0955, idProduct=09ff [ 8.283835] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6 [ 8.291947] usb 2-1: Product: USB 10/100/1000 LAN [ 8.297695] hub 1-3:1.0: USB hub found [ 8.302461] usb 2-1: Manufacturer: Nvidia [ 8.307442] usb 2-1: SerialNumber: 000001000000 [ 8.313028] hub 1-3:1.0: 4 ports detected [ 8.323108] xhci-tegra 70090000.xusb: tegra_xhci_mbox_work mailbox command 6 [ 8.439166] usb 2-2: new SuperSpeed USB device number 3 using xhci-tegra [ 8.463756] usb 2-2: New USB device found, idVendor=0424, idProduct=5534 [ 8.470530] usb 2-2: New USB device strings: Mfr=2, Product=3, SerialNumber=0 [ 8.479632] usb 2-2: Product: USB5534B [ 8.483522] usb 2-2: Manufacturer: SMSC [ 8.494406] hub 2-2:1.0: USB hub found [ 8.498669] hub 2-2:1.0: 4 ports detected Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: nvidia (automatic login) Last login: Wed Oct 4 11:58:58 JST 2017 on ttyS0 Welcome to Ubuntu 16.04 LTS (GNU/Linux 4.4.38-tegra aarch64) * Documentation: https://help.ubuntu.com/ 526 packages can be updated. 239 updates are security updates. nvidia@tegra-ubuntu:~$ [ 8.579322] usb 2-1: reset SuperSpeed USB device number 2 using xhci-tegra [ 8.600586] xhci-tegra 70090000.xusb: tegra_xhci_mbox_work mailbox command 17 [ 8.601697] xhci-tegra 70090000.xusb: tegra_xhci_mbox_work mailbox command 18 [ 8.629227] r8152 2-1:1.0 eth0: v2.03.3 (2015/01/29) [ 8.629231] r8152 2-1:1.0 eth0: This product is covered by one or more of the following patents: [ 8.629231] US6,570,884, US6,115,776, and US6,327,625. [ 8.629231] [ 8.749095] tegradc tegradc.0: nominal-pclk:25200000 parent:25800000 div:1.5 pclk:17200000 24948000~27468000 [ 8.749098] tegradc tegradc.0: pclk out of range! [ 8.749101] tegradc tegradc.0: tegra_dc_init: tegra_dc_program_mode failed [ 9.287219] tegradc tegradc.0: _tegra_dc_controller_enable: tegra_dc_init failed [ 9.595731] tegradc tegradc.0: nominal-pclk:25200000 parent:25800000 div:1.5 pclk:17200000 24948000~27468000 [ 9.595758] tegradc tegradc.0: pclk out of range! [ 9.595782] tegradc tegradc.0: tegra_dc_init: tegra_dc_program_mode failed [ 9.770580] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 9.871286] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 10.135185] tegradc tegradc.0: _tegra_dc_controller_enable: tegra_dc_init failed [ 11.588813] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 11.704513] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead. [ 13.343733] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 13.379079] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 13.406404] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 13.435273] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 13.436792] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 13.438562] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 13.464243] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 13.465867] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 13.478025] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 13.513136] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 13.521022] tegradc tegradc.0: nominal-pclk:25200000 parent:25800000 div:1.5 pclk:17200000 24948000~27468000 [ 13.521026] tegradc tegradc.0: pclk out of range! [ 13.521029] tegradc tegradc.0: tegra_dc_init: tegra_dc_program_mode failed [ 14.058722] tegradc tegradc.0: _tegra_dc_controller_enable: tegra_dc_init failed [ 14.385094] tegradc tegradc.0: nominal-pclk:25200000 parent:25800000 div:1.5 pclk:17200000 24948000~27468000 [ 14.385097] tegradc tegradc.0: pclk out of range! [ 14.385100] tegradc tegradc.0: tegra_dc_init: tegra_dc_program_mode failed [ 14.919182] tegradc tegradc.0: _tegra_dc_controller_enable: tegra_dc_init failed