[12-17 15:21:41:471][12-17 15:21:41:471] [12-17 15:21:41:643] [12-17 15:21:41:659]Ubuntu 18.04.3 LTS Sercomm ttyS0 [12-17 15:21:41:659] [12-17 15:22:00:281]Sercomm login: [ 1479.522339] tegra-i2c 7000c700.i2c: pio timed out addr: 0x50 tle[12-17 15:22:00:281]n:28 rlen:128 [12-17 15:22:00:296][ 1479.522370] tegra-i2c 7000c700.i2c: --- register dump for debugging ---- [12-17 15:22:00:296][ 1479.522402] tegra-i2c 7000c700.i2c: I2C_CNFG - 0x22c00 [12-17 15:22:00:296][ 1479.522431] tegra-i2c 7000c700.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [12-17 15:22:00:312][ 1479.522462] tegra-i2c 7000c700.i2c: I2C_FIFO_CONTROL - 0xe0 [12-17 15:22:00:312][ 1479.522492] tegra-i2c 7000c700.i2c: I2C_FIFO_STATUS - 0x800040 [12-17 15:22:00:328][ 1479.522525] tegra-i2c 7000c700.i2c: I2C_INT_MASK - 0x7d [12-17 15:22:00:328][ 1479.522555] tegra-i2c 7000c700.i2c: I2C_INT_STATUS - 0x0 [12-17 15:22:00:343][ 1479.522593] tegra-i2c 7000c700.i2c: i2c transfer timed out addr: 0x50 [12-17 15:22:00:890][ 1480.136835] watchdog: watchdog0: watchdog did not stop! [12-17 15:22:00:906][ 1480.148566] systemd-shutdow: 42 output lines suppressed due to ratelimiting [12-17 15:22:01:218][ 1480.462441] tegra-xusb 70090000.xusb: Host not halted after 16000 microseconds. [12-17 15:22:01:234][ 1480.485773] reboot: Restarting system [12-17 15:22:01:390][0000.161] [TegraBoot] (version 00.00.2018.01-l4t-7da7a580) [12-17 15:22:01:390][0000.166] Processing in cold boot mode Bootloader 2 [12-17 15:22:01:405][0000.170] A02 Bootrom Patch rev = 1023 [12-17 15:22:01:405][0000.174] Power-up reason: software reset [12-17 15:22:01:405][0000.178] No Battery Present [12-17 15:22:01:421][0000.180] pmic max77620 reset reason [12-17 15:22:01:421][0000.184] pmic max77620 NVERC : 0x0 [12-17 15:22:01:421][0000.187] RamCode = 0 [12-17 15:22:01:429][0000.189] Platform has DDR4 type RAM [12-17 15:22:01:429][0000.193] max77620 disabling SD1 Remote Sense [12-17 15:22:01:429][0000.197] Setting DDR voltage to 1125mv [12-17 15:22:01:445][0000.201] Serial Number of Pmic Max77663: 0x806e7 [12-17 15:22:01:445][0000.208] Entering ramdump check [12-17 15:22:01:445][0000.211] Get RamDumpCarveOut = 0x0 [12-17 15:22:01:445][0000.215] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [12-17 15:22:01:460][0000.220] Last reboot was clean, booting normally! [12-17 15:22:01:460][0000.224] Sdram initialization is successful [12-17 15:22:01:460][0000.228] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [12-17 15:22:01:476][0000.235] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [12-17 15:22:01:476][0000.240] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [12-17 15:22:01:492][0000.246] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [12-17 15:22:01:492][0000.252] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [12-17 15:22:01:492][0000.258] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [12-17 15:22:01:507][0000.264] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [12-17 15:22:01:523][0000.270] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [12-17 15:22:01:523][0000.286] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [12-17 15:22:01:523][0000.292] Platform-DebugCarveout: 0 [12-17 15:22:01:554][0000.295] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [12-17 15:22:01:554][0000.301] Non secure mode, and RB not enabled. [12-17 15:22:01:679][0000.432] Csd NumOfBlocks=31116288 [12-17 15:22:01:679][0000.437] Set High speed to 1 [12-17 15:22:01:679][0000.440] Error mask set in wait for cmd complete with error 0x3 in HwSdmmcWaitFo[12-17 15:22:01:695]rCommandComplete func at 278 line [12-17 15:22:01:695][0000.451] Command complete wait failed with error 0x3 Interrupt 0x18001 [12-17 15:22:01:710][0000.457] Number of retries left 4 [12-17 15:22:01:726][0000.465] Using GPT Primary to query partitions [12-17 15:22:01:726][0000.470] Loading Tboot-CPU binary [12-17 15:22:01:742][0000.482] Verifying TBC in OdmNonSecureSBK mode [12-17 15:22:01:742][0000.492] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [12-17 15:22:01:742][0000.499] Bootloader downloaded successfully. [12-17 15:22:01:742][0000.504] Downloaded Tboot-CPU binary to 0xa0000258 [12-17 15:22:01:757][0000.509] MAX77620_GPIO5 configured [12-17 15:22:01:757][0000.512] CPU power rail is up [12-17 15:22:01:757][0000.515] CPU clock enabled [12-17 15:22:01:757][0000.518] Performing RAM repair [12-17 15:22:01:773][0000.521] Updating A64 Warmreset Address to 0xa00002e9 [12-17 15:22:01:773][0000.526] Loading NvTbootBootloaderDTB [12-17 15:22:01:820][0000.564] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [12-17 15:22:01:882][0000.629] Bootloader DTB Load Address: 0x83000000 [12-17 15:22:01:882][0000.634] Loading NvTbootKernelDTB [12-17 15:22:01:929][0000.671] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [12-17 15:22:01:992][0000.736] Kernel DTB Load Address: 0x83100000 [12-17 15:22:02:007][0000.743] Loading cboot binary [12-17 15:22:02:054][0000.786] Verifying EBT in OdmNonSecureSBK mode [12-17 15:22:02:085][0000.829] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [12-17 15:22:02:085][0000.836] Bootloader downloaded successfully. [12-17 15:22:02:085][0000.840] Next binary entry address: 0x92c00258 [12-17 15:22:02:101][0000.845] BoardId: 3448 [12-17 15:22:02:101][0000.849] Overriding pmu board id with proc board id [12-17 15:22:02:117][0000.854] Display board id is not available [12-17 15:22:02:164][0000.897] Verifying SC7EntryFw in OdmNonSecureSBK mode [12-17 15:22:02:195][0000.949] /bpmp deleted [12-17 15:22:02:210][0000.951] SC7EntryFw header found loaded at 0xff700000 [12-17 15:22:02:398][0001.139] OVR2 PMIC [12-17 15:22:02:398][0001.141] Bpmp FW successfully loaded [12-17 15:22:02:413][0001.147] WB0 init successfully at 0xff780000 [12-17 15:22:02:413][0001.151] Set NvDecSticky Bits [12-17 15:22:02:413][0001.155] GSC2 address ff53fffc value c0edbbcc [12-17 15:22:02:429][0001.161] GSC MC Settings done [12-17 15:22:02:429][0001.166] TOS Image length 53680 [12-17 15:22:02:445][0001.169] Monitor size 53680 [12-17 15:22:02:445][0001.172] OS size 0 [12-17 15:22:02:445][0001.182] Secure Os AES-CMAC Verification Success! [12-17 15:22:02:460][0001.187] TOS image cipher info: plaintext [12-17 15:22:02:460][0001.191] Loading and Validation of Secure OS Successful [12-17 15:22:02:460][0001.207] SC7 Entry Firmware - 0xff700000, 0x4000 [12-17 15:22:02:476][0001.211] NvTbootPackSdramParams: start. [12-17 15:22:02:476][0001.216] NvTbootPackSdramParams: done. [12-17 15:22:02:476][0001.220] Tegraboot started after 88901 us [12-17 15:22:02:491][0001.224] Basic modules init took 790501 us [12-17 15:22:02:491][0001.228] NvTbootQspiFlashIoctl: Opcode = 1 not supported [12-17 15:22:02:491][0001.233] Sec Bootdevice Read Time = 622327755 ms, Read Size = 622327755 KB [12-17 15:22:02:507][0001.240] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [12-17 15:22:02:507][0001.246] Storage Device Read Time = 179 ms, Read Size = 2226 KB [12-17 15:22:02:507][0001.251] Storage Device Write Time = 0 ms, Write Size = 0 KB [12-17 15:22:02:523][0001.257] Next stage binary read took 39346 us [12-17 15:22:02:523][0001.261] Carveout took -51010 us [12-17 15:22:02:523][0001.264] CPU initialization took 382120 us [12-17 15:22:02:538][0001.268] Total time taken by TegraBoot 1160957 us [12-17 15:22:02:538] [12-17 15:22:02:538][0001.273] Starting CPU & Halting co-processor [12-17 15:22:02:538] [12-17 15:22:02:538]64NOTICE: BL31: v1.3(release):a28d87f09 [12-17 15:22:02:554]NOTICE: BL31: Built : 13:38:45, Nov 5 2019 [12-17 15:22:02:570]ERROR: Error initializing runtime service trusty_fast [12-17 15:22:02:664][0001.395] RamCode = 0 [12-17 15:22:02:664][0001.400] LPDDR4 Training: Read DT: Number of tables = 2 [12-17 15:22:02:679][0001.405] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [12-17 15:22:02:679][0001.418] EMC Training Successful [12-17 15:22:02:694][0001.421] 408000 not found in DVFS table [12-17 15:22:02:694][0001.427] RamCode = 0 [12-17 15:22:02:694][0001.431] DT Write: emc-table@204000 succeeded [12-17 15:22:02:710][0001.436] DT Write: emc-table@1600000 succeeded [12-17 15:22:02:710][0001.440] LPDDR4 Training: Write DT: Number of tables = 2 [12-17 15:22:02:710][0001.484] [12-17 15:22:02:710][0001.485] Debug Init done [12-17 15:22:02:726][0001.488] Marked DTB cacheable [12-17 15:22:02:726][0001.490] Bootloader DTB loaded at 0x83000000 [12-17 15:22:02:726][0001.495] Marked DTB cacheable [12-17 15:22:02:742][0001.498] Kernel DTB loaded at 0x83100000 [12-17 15:22:02:742][0001.502] DeviceTree Init done [12-17 15:22:02:742][0001.514] Pinmux applied successfully [12-17 15:22:02:757][0001.518] gicd_base: 0x50041000 [12-17 15:22:02:757][0001.522] gicc_base: 0x50042000 [12-17 15:22:02:757][0001.525] Interrupts Init done [12-17 15:22:02:757][0001.529] Using base:0x60005090 & irq:208 for tick-timer [12-17 15:22:02:757][0001.534] Using base:0x60005098 for delay-timer [12-17 15:22:02:773][0001.538] platform_init_timer: DONE [12-17 15:22:02:773][0001.542] Timer(tick) Init done [12-17 15:22:02:773][0001.546] osc freq = 38400 khz [12-17 15:22:02:773][0001.550] [12-17 15:22:02:773][0001.551] welcome to cboot [12-17 15:22:02:773][0001.553] [12-17 15:22:02:788][0001.555] Cboot Version: 00.00.2018.01-t210-21e03500 [12-17 15:22:02:788][0001.559] calling constructors [12-17 15:22:02:788][0001.562] initializing heap [12-17 15:22:02:788][0001.565] initializing threads [12-17 15:22:02:804][0001.568] initializing timers [12-17 15:22:02:804][0001.571] creating bootstrap completion thread [12-17 15:22:02:804][0001.575] top of bootstrap2() [12-17 15:22:02:804][0001.578] CPU: ARM Cortex A57 [12-17 15:22:02:819][0001.581] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [12-17 15:22:02:819][0001.586] initializing platform [12-17 15:22:02:819][0001.589] Scratch reg 37 & 271 initial value set.. [12-17 15:22:02:835][0001.595] cboot:secure-pmc present [12-17 15:22:02:835][0001.599] Manufacturer: MF = 0xc2, ID MSB = 0x25 [12-17 15:22:02:835][0001.603] ID LSB = 0x36, ID-CFI len = 194 bytes [12-17 15:22:02:835][0001.608] Macronix QSPI chip present [12-17 15:22:02:851][0001.611] SPI device register [12-17 15:22:02:851][0001.614] init boot device [12-17 15:22:02:866][0001.616] allocating memory for boot device(SPI) [12-17 15:22:02:866][0001.621] registering boot device [12-17 15:22:02:866][0001.630] sdmmc node status = okay [12-17 15:22:02:866][0001.634] sdcard instance = 0 [12-17 15:22:02:866][0001.636] sdcard gpio handle 0x56 [12-17 15:22:02:866][0001.640] sdcard gpio pin 0xc9 [12-17 15:22:02:866][0001.643] sdcard gpio flags 0x0 [12-17 15:22:02:882][0001.646] vmmc-supply 0x99 [12-17 15:22:02:882][0001.648] Instance: 0 [12-17 15:22:02:882][0001.650] Allocating memory for context [12-17 15:22:02:882][0001.654] enabling clock [12-17 15:22:02:882][0001.657] sd card init [12-17 15:22:02:898][0001.659] Check card present and stable [12-17 15:22:02:898][0001.663] Send command 0 [12-17 15:22:02:913][0001.683] Send command 3 [12-17 15:22:02:913][0001.687] Set RCA for the card [12-17 15:22:02:929][0001.690] Query card specific data by command 9 [12-17 15:22:02:929][0001.697] Parse CSD data [12-17 15:22:02:944][0001.699] Send command 7 [12-17 15:22:02:944][0001.710] Calling sd device register [12-17 15:22:02:944][0001.713] Init sdcard [12-17 15:22:02:944][0001.715] Allocating memory for boot device [12-17 15:22:02:960][0001.719] Registering user device [12-17 15:22:02:960][0001.733] Enable APE clock [12-17 15:22:02:976][0001.735] Un-powergate APE partition [12-17 15:22:02:976][0001.739] of_register: registering tegra_udc to of_hal [12-17 15:22:02:976][0001.744] of_register: registering tegra_udc to of_hal [12-17 15:22:02:976][0001.749] of_register: registering inv20628-driver to of_hal [12-17 15:22:02:991][0001.754] of_register: registering ads1015-driver to of_hal [12-17 15:22:02:991][0001.760] of_register: registering lp8557-bl-driver to of_hal [12-17 15:22:02:991][0001.766] of_register: registering bq2419x_charger to of_hal [12-17 15:22:03:007][0001.771] of_register: registering cpc to of_hal [12-17 15:22:03:023][0001.776] of_register: registering bq27441_fuel_gauge to of_hal [12-17 15:22:03:023][0001.787] gpio framework initialized [12-17 15:22:03:023][0001.791] of_register: registering tca9539_gpio to of_hal [12-17 15:22:03:023][0001.796] of_register: registering tca9539_gpio to of_hal [12-17 15:22:03:038][0001.801] of_register: registering i2c_bus_driver to of_hal [12-17 15:22:03:038][0001.807] of_register: registering i2c_bus_driver to of_hal [12-17 15:22:03:038][0001.813] of_register: registering i2c_bus_driver to of_hal [12-17 15:22:03:054][0001.818] of_register: registering i2c_bus_driver to of_hal [12-17 15:22:03:054][0001.824] pmic framework initialized [12-17 15:22:03:054][0001.827] of_register: registering max77620_pmic to of_hal [12-17 15:22:03:070][0001.833] regulator framework initialized [12-17 15:22:03:070][0001.837] of_register: registering tps65132_bl_driver to of_hal [12-17 15:22:03:085][0001.842] initializing target [12-17 15:22:03:085][0001.848] gpio_driver_register: register 'tegra_gpio_driver' driver [12-17 15:22:03:101][0001.857] fixed regulator driver initialized [12-17 15:22:03:101][0001.874] initializing OF layer [12-17 15:22:03:116][0001.877] NCK carveout not present [12-17 15:22:03:116][0001.880] Skipping dts_overrides [12-17 15:22:03:132][0001.884] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [12-17 15:22:03:132][0001.901] I2C Bus Init done [12-17 15:22:03:148][0001.903] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [12-17 15:22:03:148][0001.913] I2C Bus Init done [12-17 15:22:03:163][0001.916] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [12-17 15:22:03:163][0001.926] I2C Bus Init done [12-17 15:22:03:163][0001.929] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [12-17 15:22:03:179][0001.939] I2C Bus Init done [12-17 15:22:03:179][0001.942] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [12-17 15:22:03:179][0001.952] I2C Bus Init done [12-17 15:22:03:194][0001.955] of_children_init: Ops found for compatible string maxim,max77620 [12-17 15:22:03:194][0001.965] max77620_init using irq 118 [12-17 15:22:03:210][0001.970] register 'maxim,max77620' pmic [12-17 15:22:03:210][0001.974] gpio_driver_register: register 'max77620-gpio' driver [12-17 15:22:03:226][0001.980] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [12-17 15:22:03:226][0001.991] I2C Bus Init done [12-17 15:22:03:226][0001.994] NCK carveout not present [12-17 15:22:03:241][0001.998] shim_invoke: No NCT, Calling dts updates [12-17 15:22:03:257][0002.009] Find /i2c@7000c000's alias i2c0 [12-17 15:22:03:257][0002.013] get eeprom at 1-a0, size 256, type 0 [12-17 15:22:03:257][0002.021] Find /i2c@7000c500's alias i2c2 [12-17 15:22:03:257][0002.025] get eeprom at 3-a0, size 256, type 0 [12-17 15:22:03:257][0002.030] get eeprom at 3-ae, size 256, type 0 [12-17 15:22:03:272][0002.034] pm_ids_update: Updating 1,a0, size 256, type 0 [12-17 15:22:03:272][0002.039] I2C slave not started [12-17 15:22:03:272][0002.042] I2C write failed [12-17 15:22:03:272][0002.045] Writing offset failed [12-17 15:22:03:272][0002.048] eeprom_init: EEPROM read failed [12-17 15:22:03:288][0002.052] pm_ids_update: eeprom init failed [12-17 15:22:03:304][0002.056] pm_ids_update: Updating 3,a0, size 256, type 0 [12-17 15:22:03:319][0002.086] pm_ids_update: The pm board id is 3448-0000-200 [12-17 15:22:03:335][0002.093] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50 [12-17 15:22:03:335][0002.101] pm_ids_update: pm id update successful [12-17 15:22:03:335][0002.105] pm_ids_update: Updating 3,ae, size 256, type 0 [12-17 15:22:03:335][0002.110] I2C slave not started [12-17 15:22:03:335][0002.113] I2C write failed [12-17 15:22:03:351][0002.116] Writing offset failed [12-17 15:22:03:351][0002.119] eeprom_init: EEPROM read failed [12-17 15:22:03:367][0002.123] pm_ids_update: eeprom init failed [12-17 15:22:03:382][0002.153] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [12-17 15:22:03:397][0002.159] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [12-17 15:22:03:397][0002.167] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [12-17 15:22:03:413][0002.173] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [12-17 15:22:03:429][0002.182] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e4:3f:8d [12-17 15:22:03:429][0002.188] Plugin Manager: Parse ODM data 0x00094000 [12-17 15:22:03:429][0002.198] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait[12-17 15:22:03:444] rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [12-17 15:22:03:444][0002.219] Find /i2c@7000c000's alias i2c0 [12-17 15:22:03:460][0002.223] get eeprom at 1-a0, size 256, type 0 [12-17 15:22:03:460][0002.232] Find /i2c@7000c500's alias i2c2 [12-17 15:22:03:476][0002.236] get eeprom at 3-a0, size 256, type 0 [12-17 15:22:03:476][0002.240] get eeprom at 3-ae, size 256, type 0 [12-17 15:22:03:476][0002.244] pm_ids_update: Updating 1,a0, size 256, type 0 [12-17 15:22:03:476][0002.250] I2C slave not started [12-17 15:22:03:476][0002.253] I2C write failed [12-17 15:22:03:491][0002.255] Writing offset failed [12-17 15:22:03:491][0002.258] eeprom_init: EEPROM read failed [12-17 15:22:03:507][0002.262] pm_ids_update: eeprom init failed [12-17 15:22:03:507][0002.266] pm_ids_update: Updating 3,a0, size 256, type 0 [12-17 15:22:03:523][0002.297] pm_ids_update: The pm board id is 3448-0000-200 [12-17 15:22:03:538][0002.303] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50 [12-17 15:22:03:538][0002.310] pm_ids_update: pm id update successful [12-17 15:22:03:554][0002.315] pm_ids_update: Updating 3,ae, size 256, type 0 [12-17 15:22:03:554][0002.320] I2C slave not started [12-17 15:22:03:554][0002.323] I2C write failed [12-17 15:22:03:554][0002.326] Writing offset failed [12-17 15:22:03:554][0002.329] eeprom_init: EEPROM read failed [12-17 15:22:03:570][0002.333] pm_ids_update: eeprom init failed [12-17 15:22:03:601][0002.363] Chip UID is 000000016442128914000000180184c0 [12-17 15:22:03:601][0002.368] Add serial number:04213190282780c08401 as DT property [12-17 15:22:03:616][0002.376] Applying platform configs [12-17 15:22:03:632][0002.383] platform-init is not present. Skipping [12-17 15:22:03:632][0002.387] calling apps_init() [12-17 15:22:03:632][0002.407] Found 14 GPT partitions in "sd0" [12-17 15:22:03:647][0002.411] Proceeding to Cold Boot [12-17 15:22:03:647][0002.414] starting app android_boot_app [12-17 15:22:03:663][0002.418] Device state: unlocked [12-17 15:22:03:663][0002.421] display console init [12-17 15:22:03:679][0002.429] could not find regulator [12-17 15:22:03:679][0002.433] hdmi cable connected [12-17 15:22:03:710][0002.464] DT entry for leds-pwm not found [12-17 15:22:05:678][0004.443] I2C transfer timeout [12-17 15:22:05:678][0004.446] I2C write failed [12-17 15:22:05:678][0004.448] Writing offset failed [12-17 15:22:05:678][0004.451] could not read edid [12-17 15:22:05:694][0004.457] tmds-config node not found [12-17 15:22:05:694][0004.461] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltageprop[12-17 15:22:05:709]setting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [12-17 15:22:05:709][0004.476] setting 'vdd-1v8' regulator to 1800000 micro volts [12-17 15:22:05:725][0004.484] could not find regulator [12-17 15:22:05:725][0004.487] could not find regulator [12-17 15:22:05:725][0004.490] could not find regulator [12-17 15:22:05:756][0004.518] using default cmu settings [12-17 15:22:05:756][0004.522] dc_hdmi_enable, starting HDMI initialisation [12-17 15:22:05:756][0004.529] dc_hdmi_enable, HDMI initialisation complete [12-17 15:22:05:772][0004.534] list and configure display window [12-17 15:22:05:772][0004.538] display console init completed [12-17 15:22:05:772][0004.546] subnode volume_up is not found ! [12-17 15:22:05:787][0004.550] subnode back is not found ! [12-17 15:22:05:787][0004.553] subnode volume_down is not found ! [12-17 15:22:05:787][0004.557] subnode menu is not found ! [12-17 15:22:05:803][0004.561] Gpio keyboard init success [12-17 15:22:05:850][0004.607] found decompressor handler: lz4-legacy [12-17 15:22:05:866][0004.621] decompressing blob (type 1)... [12-17 15:22:05:897][0004.655] load_bmp_blob: panelresolution=480 type=0 [12-17 15:22:05:944][0004.707] decompressor handler not found [12-17 15:22:05:944][0004.711] load_firmware_blob: Firmware blob loaded, entries=2 [12-17 15:22:05:944][0004.717] se_aes_verify_sbk_clear: Error [12-17 15:22:05:960][0004.721] bl_battery_charging: connected to external power supply [12-17 15:22:05:960][0004.728] xusb is supported [12-17 15:22:05:975][0004.734] error while finding nvidia,portmap [12-17 15:22:05:975][0004.739] could not find regulator [12-17 15:22:06:475][0005.243] xusb blob version 0 size 124416 [12-17 15:22:06:475][0005.247] firmware size 124416 [12-17 15:22:06:491][0005.251] Firmware timestamp: 0x5cd2a472, Version: 50.22 release [12-17 15:22:06:506][0005.261] xhci0: 64 bytes context size, 32-bit DMA [12-17 15:22:06:538][0005.301] usbus0: 5.0Gbps Super Speed USB v3.0 [12-17 15:22:06:569][0005.321] uhub0: on usbu[12-17 15:22:06:569]s0 [12-17 15:22:07:209][0005.971] uhub0: 9 ports with 9 removable, self powered [12-17 15:22:08:209][0006.971] failed to get HID devices [12-17 15:22:08:209][0006.974] failed to init xhci or no usb device attached [12-17 15:22:08:225][0006.985] device_query_partition_size: failed to open partition sd0:MSC ! [12-17 15:22:08:225][0006.991] MSC Partition not found [12-17 15:22:08:240][0006.998] device_query_partition_size: failed to open partition sd0:USP ! [12-17 15:22:08:240][0007.004] USP partition read failed! [12-17 15:22:08:240][0007.008] blob_init: blob-partition USP header read failed [12-17 15:22:08:240][0007.013] android_boot Unable to update recovery partition [12-17 15:22:08:256][0007.019] kfs_getpartname: name = LNX [12-17 15:22:08:272][0007.022] Loading kernel from LNX [12-17 15:22:08:318][0007.082] Verifying boot image in OdmNonSecureSBK mode [12-17 15:22:08:350][0007.126] kernel load address: 0x80080000, size: 482032 bytes [12-17 15:22:08:365][0007.131] ramdisk load address: 0x84100000, size: 0 bytes [12-17 15:22:08:381][0007.137] load kernel from storage [12-17 15:22:08:397][0007.148] decompressor handler not found [12-17 15:22:08:443][0007.205] Successfully loaded kernel and ramdisk images [12-17 15:22:08:459][0007.212] load_bmp_blob: panelresolution=480 type=0 [12-17 15:22:08:521][0007.286] display bmp image done [12-17 15:22:08:529][0007.289] NCK carveout not present [12-17 15:22:08:529][0007.292] Skipping dts_overrides [12-17 15:22:08:529][0007.295] NCK carveout not present [12-17 15:22:08:545][0007.298] shim_invoke: No NCT, Calling dts updates [12-17 15:22:08:545][0007.310] Find /i2c@7000c000's alias i2c0 [12-17 15:22:08:560][0007.313] get eeprom at 1-a0, size 256, type 0 [12-17 15:22:08:560][0007.322] Find /i2c@7000c500's alias i2c2 [12-17 15:22:08:560][0007.326] get eeprom at 3-a0, size 256, type 0 [12-17 15:22:08:560][0007.330] get eeprom at 3-ae, size 256, type 0 [12-17 15:22:08:560][0007.335] pm_ids_update: Updating 1,a0, size 256, type 0 [12-17 15:22:08:576][0007.340] I2C slave not started [12-17 15:22:08:576][0007.343] I2C write failed [12-17 15:22:08:576][0007.346] Writing offset failed [12-17 15:22:08:576][0007.349] eeprom_init: EEPROM read failed [12-17 15:22:08:592][0007.353] pm_ids_update: eeprom init failed [12-17 15:22:08:607][0007.357] pm_ids_update: Updating 3,a0, size 256, type 0 [12-17 15:22:08:623][0007.387] pm_ids_update: The pm board id is 3448-0000-200 [12-17 15:22:08:638][0007.394] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50 [12-17 15:22:08:638][0007.401] pm_ids_update: pm id update successful [12-17 15:22:08:638][0007.406] pm_ids_update: Updating 3,ae, size 256, type 0 [12-17 15:22:08:638][0007.411] I2C slave not started [12-17 15:22:08:638][0007.414] I2C write failed [12-17 15:22:08:638][0007.417] Writing offset failed [12-17 15:22:08:670][0007.420] eeprom_init: EEPROM read failed [12-17 15:22:08:670][0007.424] pm_ids_update: eeprom init failed [12-17 15:22:08:686][0007.454] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [12-17 15:22:08:701][0007.460] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [12-17 15:22:08:701][0007.468] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [12-17 15:22:08:717][0007.474] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [12-17 15:22:08:717][0007.482] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e4:3f:8d [12-17 15:22:08:732][0007.489] Plugin Manager: Parse ODM data 0x00094000 [12-17 15:22:08:732][0007.499] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait[12-17 15:22:08:748] rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [12-17 15:22:08:748][0007.514] Add serial number:04213190282780c08401 as DT property [12-17 15:22:08:764][0007.523] "bpmp" doesn't exist, creating [12-17 15:22:08:764][0007.528] Updated bpmp info to DTB [12-17 15:22:08:764][0007.533] Updated initrd info to DTB [12-17 15:22:08:764][0007.537] "proc-board" doesn't exist, creating [12-17 15:22:08:764][0007.542] Updated board info to DTB [12-17 15:22:08:779][0007.546] "pmu-board" doesn't exist, creating [12-17 15:22:08:779][0007.551] Updated board info to DTB [12-17 15:22:08:795][0007.555] "display-board" doesn't exist, creating [12-17 15:22:08:795][0007.560] Updated board info to DTB [12-17 15:22:08:795][0007.564] "reset" doesn't exist, creating [12-17 15:22:08:795][0007.568] Updated reset info to DTB [12-17 15:22:08:810][0007.571] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 [12-17 15:22:08:810]vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 vi[12-17 15:22:08:826]deo=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 ea[12-17 15:22:08:826]rlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0[12-17 15:22:08:826]x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 tegra_fbmem=0x140000@0x92cb3000[12-17 15:22:08:841] is_hdmi_initialised=1 [12-17 15:22:08:841][0007.610] DTB cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=tt[12-17 15:22:08:857]yS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [12-17 15:22:08:857][0007.623] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 con[12-17 15:22:08:857]sole=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [12-17 15:22:08:873][0007.636] Updated bootarg info to DTB [12-17 15:22:08:873][0007.639] Adding uuid 000000016442128914000000180184c0 to DT [12-17 15:22:08:873][0007.645] Adding eks info 0 to DT [12-17 15:22:08:888][0007.651] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [12-17 15:22:08:888][0007.657] Updated memory info to DTB [12-17 15:22:08:904][0007.665] set vdd_core voltage to 1075 mv [12-17 15:22:08:920][0007.669] setting 'vdd-core' regulator to 1075000 micro volts [12-17 15:22:08:920][0007.691] could not find regulator [12-17 15:22:08:935][0007.695] Found secure-pmc; disable BPMP [12-17 15:22:08:982] [12-17 15:22:08:982] [12-17 15:22:08:982]U-Boot 2016.07-gd917e08cec (Nov 05 2019 - 13:38:56 -0800) [12-17 15:22:08:982] [12-17 15:22:08:982]TEGRA210 [12-17 15:22:08:982]Model: NVIDIA P3450-Porg [12-17 15:22:08:982]Board: NVIDIA P3450-PORG [12-17 15:22:09:170]DRAM: 4 GiB [12-17 15:22:09:279]MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 [12-17 15:22:09:279]Using default environment [12-17 15:22:09:279] [12-17 15:22:09:279]In: serial [12-17 15:22:09:295]Out: serial [12-17 15:22:09:295]Err: serial [12-17 15:22:09:295]Net: No ethernet found. [12-17 15:22:10:576]Hit any key to stop autoboot: 0 [12-17 15:22:10:622]switch to partitions #0, OK [12-17 15:22:10:622]mmc1 is current device [12-17 15:22:11:357]Scanning mmc 1:1... [12-17 15:22:11:825]Found /boot/extlinux/extlinux.conf [12-17 15:22:11:841]Retrieving file: /boot/extlinux/extlinux.conf [12-17 15:22:11:966]733 bytes read in 100 ms (6.8 KiB/s) [12-17 15:22:11:966]L4T boot options [12-17 15:22:11:966]1: primary kernel [12-17 15:22:14:966]Enter choice: 1: primary kernel [12-17 15:22:14:966]Retrieving file: /boot/initrd [12-17 15:22:15:278]5562303 bytes read in 300 ms (17.7 MiB/s) [12-17 15:22:15:294]Retrieving file: /boot/Image [12-17 15:22:16:825]34179080 bytes read in 1529 ms (21.3 MiB/s) [12-17 15:22:16:825]append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize u[12-17 15:22:16:840]sb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb [12-17 15:22:16:840]no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=ua[12-17 15:22:16:856]rt8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff78[12-17 15:22:16:856]0000 core_edp_mv=1075 core_edp_ma=4000 tegra_fbmem=0x140000@0x92cb3000 is_hdmi_ini[12-17 15:22:16:872]tialised=1 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8[12-17 15:22:16:872] console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait rootfst[12-17 15:22:16:872]ype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 quiet [12-17 15:22:16:888]## Flattened Device Tree blob at 83100000 [12-17 15:22:16:888] Booting using the fdt blob at 0x83100000 [12-17 15:22:16:888] reserving fdt memory region: addr=80000000 size=20000 [12-17 15:22:16:903] Using Device Tree in place at 0000000083100000, end 0000000083177282 [12-17 15:22:16:919] [12-17 15:22:16:919]Starting kernel ... [12-17 15:22:16:919] [12-17 15:22:17:981] [12-17 15:22:18:590][ 1.224114] imx219 6-0010: imx219_board_setup: error during i2c read probe (-12[12-17 15:22:18:590]1) [12-17 15:22:18:606][ 1.231689] imx219 6-0010: board setup failed [12-17 15:22:28:498][ 11.126398] tegra-i2c 7000c700.i2c: pio timed out addr: 0x50 tlen:28 rlen:128 [12-17 15:22:28:498][ 11.133545] tegra-i2c 7000c700.i2c: --- register dump for debugging ---- [12-17 15:22:28:513][ 11.140282] tegra-i2c 7000c700.i2c: I2C_CNFG - 0x22c00 [12-17 15:22:28:513][ 11.145419] tegra-i2c 7000c700.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [12-17 15:22:28:513][ 11.152114] tegra-i2c 7000c700.i2c: I2C_FIFO_CONTROL - 0xe0 [12-17 15:22:28:529][ 11.157685] tegra-i2c 7000c700.i2c: I2C_FIFO_STATUS - 0x800040 [12-17 15:22:28:529][ 11.163515] tegra-i2c 7000c700.i2c: I2C_INT_MASK - 0x7d [12-17 15:22:28:529][ 11.168737] tegra-i2c 7000c700.i2c: I2C_INT_STATUS - 0x0 [12-17 15:22:28:545][ 11.174048] tegra-i2c 7000c700.i2c: i2c transfer timed out addr: 0x50 [12-17 15:22:28:560][ 11.181897] tegradc tegradc.1: dpd enable lookup fail:-19 [12-17 15:22:28:966][ 11.595305] cgroup: cgroup2: unknown option "nsdelegate" [12-17 15:22:29:216][ 11.843250] systemd[1]: nvargus-daemon.service: Service lacks both ExecStart= a[12-17 15:22:29:232]nd ExecStop= setting. Refusing. [12-17 15:22:30:247][ 12.883428] using random self ethernet address [12-17 15:22:30:263][ 12.887968] using random host ethernet address [12-17 15:22:30:294][ 12.923684] using random self ethernet address [12-17 15:22:30:310][ 12.928421] using random host ethernet address [12-17 15:22:30:669][ 13.299336] random: crng init done [12-17 15:22:30:685][ 13.302743] random: 7 urandom warning(s) missed due to ratelimiting [12-17 15:22:33:608] [12-17 15:22:33:628]Ubuntu 18.04.3 LTS Sercomm ttyS0 [12-17 15:22:33:628] [12-17 15:22:37:970][12-17 15:22:37:970]