[0000.024] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet lev. [0000.033] I> MB1 (prd-version: 1.5.1.7-t194-41334769-98030a79) [0000.038] I> Boot-mode: Coldboot [0000.041] I> Chip revision : A02P [0000.044] I> Bootrom patch version : 15 (correctly patched) [0000.049] I> ATE fuse revision : 0x200 [0000.053] I> Ram repair fuse : 0x0 [0000.056] I> Ram Code : 0x0 [0000.058] I> rst_source : 0x0 [0000.061] I> rst_level : 0x0 [0000.065] I> Boot-device: QSPI [0000.067] I> Qspi flash params source = brbct [0000.071] I> Qspi using bpmp-dma [0000.074] I> Qspi clock source : pllp [0000.078] I> QSPI Flash Size = 32 MB [0000.081] I> Qspi initialized successfully [0000.085] W> No valid slot number is found in scratch register [0000.091] W> Return default slot: _a [0000.094] I> Active Boot chain : 0 [0000.097] I> Boot-device: QSPI [0000.100] I> Qspi flash params source = brbct [0000.106] W> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT. [0000.113] I> Temperature = 25500 [0000.116] W> Skipping boost for clk: BPMP_CPU_NIC [0000.121] W> Skipping boost for clk: BPMP_APB [0000.125] W> Skipping boost for clk: AXI_CBB [0000.129] W> Skipping boost for clk: AON_CPU_NIC [0000.133] W> Skipping boost for clk: CAN1 [0000.137] W> Skipping boost for clk: CAN2 [0000.141] I> Boot-device: QSPI [0000.144] I> Boot-device: QSPI [0000.147] I> Qspi flash params source = mb1bct [0000.151] I> Qspi using bpmp-dma [0000.154] I> Qspi clock source : pllc_out0 [0000.157] I> Qspi reinitialized [0000.160] I> Qspi flash params source = mb1bct [0000.166] I> ECC region[0]: Start:0x0, End:0x0 [0000.170] I> ECC region[1]: Start:0x0, End:0x0 [0000.174] I> ECC region[2]: Start:0x0, End:0x0 [0000.178] I> ECC region[3]: Start:0x0, End:0x0 [0000.182] I> ECC region[4]: Start:0x0, End:0x0 [0000.186] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000 [0000.192] I> Non-ECC region[1]: Start:0x0, End:0x0 [0000.197] I> Non-ECC region[2]: Start:0x0, End:0x0 [0000.201] I> Non-ECC region[3]: Start:0x0, End:0x0 [0000.206] I> Non-ECC region[4]: Start:0x0, End:0x0 [0000.211] E> FAILED: Thermal config [0000.218] E> FAILED: MEMIO rail config [0000.228] I> Boot-device: QSPI [0000.231] I> Qspi flash params source = mb1bct [0000.240] I> Qspi flash params source = mb1bct [0000.252] I> Qspi flash params source = mb1bct [0000.318] I> Qspi flash params source = mb1bct [0000.327] I> Qspi flash params source = mb1bct [0000.356] I> Qspi flash params source = mb1bct [0000.368] I> MB1 done ����main enter SPE VERSION #: R01.00.14 Created: Sep 19 2018 @ 11:03:21 HW Function test Start Scheduler. in late init �� [0000.376] I> Welcome to MB2(TBoot-BPMP) (version: 00.00.2018.32-mobile-938a8) [0000.377] I> DMA Heap @ [0x526fa000 - 0x52ffa000] [0000.377] I> Default Heap @ [0xd486400 - 0xd48a400] [0000.378] E> DEVICE_PROD: Invalid value data = 70020000, size = 0. [0000.384] W> device prod register failed [0000.388] I> Boot-device: QSPI [0000.391] I> Boot_device: QSPI_FLASH instance: 0 [0000.396] I> QSPI Flash Size = 32 MB [0000.401] I> Qspi initialized successfully [0000.402] I> qspi flash-0 params source = boot args [0000.412] I> Found 47 partitions in QSPI_FLASH (instance 0) [0000.413] W> No valid slot number is found in scratch register [0000.418] W> Return default slot: _a [0000.422] I> Active Boot chain : 0 [0000.425] I> parsing oem signed section of bpmp-fw header done [0000.431] I> bpmp-fw binary init read from storage [0000.436] I> oem authentication of bpmp-fw header done [0000.450] I> bpmp-fw binary done read from storage [0000.450] I> bpmp-fw: Authentication init Done [0000.451] I> parsing oem signed section of cpubl header done [0000.455] I> cpubl binary init read from storage [0000.459] I> bpmp-fw: Authentication Finalize Done [0000.464] I> oem authentication of cpubl header done [0000.472] I> cpubl binary done read from storage [0000.473] I> cpubl: Authentication init Done [0000.478] I> parsing oem signed section of rce header done [0000.483] I> rce binary init read from storage [0000.487] I> Relocating BR-BCT [0000.490] I> cpubl: Authentication Finalize Done [0000.494] I> oem authentication of rce header done [0000.499] I> rce binary done read from storage [0000.503] I> rce: Authentication init Done [0000.507] I> parsing oem signed section of ape header done [0000.512] I> ape binary init read from storage [0000.517] I> rce: Authentication Finalize Done [0000.521] I> oem authentication of ape header done [0000.526] I> ape binary done read from storage [0000.530] I> ape: Authentication init Done [0000.534] I> parsing oem signed section of tos header done [0000.539] I> tos binary init read from storage [0000.543] I> ape: Authentication Finalize Done [0000.548] I> oem authentication of tos header done [0000.555] I> tos binary done read from storage [0000.557] I> tos: Authentication init Done [0000.561] I> parsing oem signed section of bpmp-fw-dtb header done [0000.567] I> bpmp-fw-dtb binary init read from storage [0000.572] I> tos: Authentication Finalize Done [0000.578] I> oem authentication of bpmp-fw-dtb header done [0000.581] I> bpmp-fw-dtb binary done read from storage [0000.586] I> bpmp-fw-dtb: Authentication init Done [0000.591] I> parsing oem signed section of cpubl-dtb header done [0000.597] I> cpubl-dtb binary init read from storage [0000.601] I> bpmp-fw-dtb: Authentication Finalize Done [0000.653] I> oem authentication of cpubl-dtb header done [0000.654] I> cpubl-dtb binary done read from storage [0000.654] I> cpubl-dtb: Authentication init Done [0000.655] I> parsing oem signed section of eks header done [0000.656] I> eks binary init read from storage [0000.656] I> cpubl-dtb: Authentication Finalize Done [0000.657] I> oem authentication of eks header done [0000.662] I> eks binary done read from storage [0000.666] I> eks: Authentication init Done [0000.670] I> eks: Authentication Finalize Done [0000.674] I> EKB detected (length: 0x410) @ VA:0x52700400 ��NOTICE: BL31: v1.3(release):b5eeb33f7 NOTICE: BL31: Built : 12:15:32, Jul 26 2021 ipc-unittest-main: 1519: Welcome to IPC unittest!!! ipc-unittest-main: 1531: waiting forever ipc-unittest-srv: 329: Init unittest services!!! hwkey-agent: 41: hwkey-agent is running!! hwkey-agent: 315: key_mgnt_processing ....... hwkey-agent: 223: Setting EKB key 0 to slot 14 hwkey-agent: 178: Init hweky-agent services!! luks-srv: 40: luks-srv is running!! luks-srv: 157: Init luks-srv IPC services!! platform_bootstrap_epilog: trusty bootstrap complete �� welcome to lk calling constructors initializing heap creating bootstrap completion thread top of bootstrap2() initializing platform bpmp: platform_init tag is e73a758761f0c6d24a1e69a2ac6b5035 tag_show initialized dt initialized mail initialized chipid initialized fuse initialized sku initialized speedo initialized ec_get_ec_list: found 45 ecs ec initialized ec_mrq initialized vmon_populate_monitors: found 3 monitors vmon initialized adc initialized fmon_populate_monitors: found 73 monitors fmon initialized fmon_mrq initialized reset initialized nvhs initialized 391 clocks registered clk_mrq_init: mrq handler registered clk initialized nvlink initialized io_dpd initialized io_dpd initialized thermal initialized i2c5 controller initialized initialized i2c mrq handling i2c initialized regulator initialized avfs_clk_platform_init: bad clk id in clock@cluster1_avfs avfs_clk_platform initialized soctherm initialized aotag initialized powergate initialized dvs initialized pm initialized pg_late initialized strap initialized tag initialized emc initialized clk_dt initialized avfs_ccplex_platform initialized tj_max: dt node not found tj_init initialized uphy_mrq_init: mrq handler registered uphy_dt initialized uphy initialized safereg_init: period 80 ms ec_late initialized �� ��mrq initialized ��[0001.032] I> Welcome to Cboot ��WARNING: no registered clock for FMON_NAFLL_CLUSTER1 (id 281) fmon_post initialized ��[0001.032] I> Cboot Version: t194-cfa2bc91 [0001.034] I> CPU-BL Params @ 0xf2820000 [0001.038] I> 0) Base:0x00000000 Size:0x00000000 [0001.043] I> 1) Base:0xf1100000 Size:0x00100000 [0001.047] I> 2) Base:0xf2000000 Size:0x00200000 [0001.051] I> 3) Base:0xf1200000 Size:0x00200000 ��clk_set_parent failed for clk i2c2, parent pll_aon (-22) clk_set_parent failed for clk i2c8, parent pll_aon (-22) clk_dt_late initialized machine_check initialized pm_post initialized dbells initialized avfs_clk_platform_post initialized dmce initialized cvc initialized ccplex_avfs_hw_init: nafll_cluster0: not monitored ccplex_avfs_hw_init: nafll_cluster2: not monitored ccplex_avfs_hw_init: nafll_cluster3: not monitored avfs_clk_mach_post initialized regulator_post initialized rm initialized sc7_diag initialized thermal_test initialized serial_late initialized clk_post initialized clk_dt_post initialized mc_reg initialized pg_post initialized dyn_modules initialized sku_debugfs initialized speedo_debugfs initialized adc_debugfs initialized Failed to register PTO counter for id 281 Failed to register PTO counter for id 281 Failed to register PTO counter for id 281 Failed to register PTO counter for id 281 clk_debugfs initialized emc_debugfs initialized dvs_debugfs initialized fmon_debugfs_init_one: no clock debugfs node to attach FMON_NAFLL_CLUSTER1 fmon_debugfs initialized vmon_debugfs initialized pg_debugfs initialized profile_fs initialized debugfs_cons initialized mail_fs initialized profile initialized cvc_debugfs initialized dmce_debugfs initialized ec_debugfs initialized rm_rail_debugfs_init: /rm/vdd_cpu: failed rm_rail_debugfs_init: /rm/vdd_cpu: failed rm_debugfs initialized soctherm_debug initialized gr_reader initialized mods initialized dt_fs initialized debugfs_mrq initialized debug_mrq initialized debug_safereg initialized initializing target calling apps_init() starting app shell entering main console loop ] ��[0001.056] I> 4) Base:0xf1000000 Size:0x00100000 [0001.210] I> 5) Base:0xf0f00000 Size:0x00100000 [0001.215] I> 6) Base:0xf3800000 Size:0x00400000 [0001.219] I> 7) Base:0xf1c00000 Size:0x00400000 [0001.223] I> 8) Base:0xf0e00000 Size:0x00100000 [0001.228] I> 9) Base:0xf0d00000 Size:0x00100000 [0001.232] I> 10) Base:0xf3000000 Size:0x00800000 [0001.237] I> 11) Base:0x40000000 Size:0x00040000 [0001.241] I> 12) Base:0xf0c00000 Size:0x00100000 [0001.246] I> 13) Base:0x40046000 Size:0x00002000 [0001.250] I> 14) Base:0x40048000 Size:0x00002000 [0001.255] I> 15) Base:0xac000000 Size:0x00004000 [0001.259] I> 16) Base:0x4004a000 Size:0x00002000 [0001.264] I> 17) Base:0xf0b00000 Size:0x00100000 [0001.268] I> 18) Base:0x4004c000 Size:0x00002000 [0001.273] I> 19) Base:0xf2200000 Size:0x00600000 [0001.277] I> 20) Base:0x4004e000 Size:0x00002000 [0001.282] I> 21) Base:0xf0ad0000 Size:0x0000c000 [0001.286] I> 22) Base:0x00000000 Size:0x00000000 [0001.290] I> 23) Base:0xf0ae0000 Size:0x00020000 [0001.295] I> 24) Base:0xf6000000 Size:0x02000000 [0001.299] I> 25) Base:0x40050000 Size:0x00002000 [0001.304] I> 26) Base:0x40040000 Size:0x00006000 [0001.308] I> 27) Base:0xf1800000 Size:0x00400000 [0001.313] I> 28) Base:0xf4c00000 Size:0x01400000 [0001.317] I> 29) Base:0xf1400000 Size:0x00400000 [0001.322] I> 30) Base:0x00000000 Size:0x00000000 [0001.326] I> 31) Base:0x00000000 Size:0x00000000 [0001.331] I> 32) Base:0xf8000000 Size:0x08000000 [0001.335] I> 33) Base:0x00000000 Size:0x00000000 [0001.340] I> 34) Base:0xf3c00000 Size:0x01000000 [0001.344] I> 35) Base:0xab000000 Size:0x01000000 [0001.348] I> 36) Base:0xa0000000 Size:0x0b000000 [0001.353] I> 37) Base:0xf2800000 Size:0x00800000 [0001.357] I> 38) Base:0x80000000 Size:0x20000000 [0001.362] I> 39) Base:0xb0000000 Size:0x08000000 [0001.366] I> 40) Base:0x00000000 Size:0x00000000 [0001.371] I> 41) Base:0x00000000 Size:0x00000000 [0001.375] I> 42) Base:0x00000000 Size:0x00000000 [0001.380] I> 43) Base:0x00000000 Size:0x00000000 [0001.384] I> 44) Base:0x00000000 Size:0x00000000 [0001.389] I> 45) Base:0x00000000 Size:0x00000000 [0001.393] GIC-SPI Target CPU: 0 [0001.396] Interrupts Init done [0001.399] calling constructors [0001.402] initializing heap [0001.404] I> Heap: [0xa0699b80 ... 0xab000000] [0001.409] initializing threads [0001.412] initializing timers [0001.414] creating bootstrap completion thread [0001.419] top of bootstrap2() [0001.422] CPU: MIDR: 0x4E0F0040, MPIDR: 0x80000000 [0001.426] initializing platform [0001.429] E> DEVICE_PROD: Invalid value data = 0, size = 0. [0001.435] W> device prod register failed [0001.438] I> Bl_dtb @0xaaf00000 [0001.444] W> "plugin-manager" doesn't exist, creating [0001.446] W> "ids" doesn't exist, creating [0001.451] W> "connection" doesn't exist, creating [0001.455] W> "configs" doesn't exist, creating [0001.466] E> failed to read label property for node 158736: 13 [0001.469] E> failed to read reg property for node 158800: 13 [0001.472] E> failed to read reg property for node 158852: 13 [0001.477] E> failed to read reg property for node 158936: 13 [0001.483] I> Find /i2c@3160000's alias i2c0 [0001.485] I> Reading eeprom i2c=0 address=0x50 [0001.515] I> Device at /i2c@3160000:0x50 [0001.515] I> Reading eeprom i2c=0 address=0x57 [0001.539] I> Device at /i2c@3160000:0x57 [0001.541] I> Find /i2c@c240000's alias i2c1 [0001.541] I> Reading eeprom i2c=1 address=0x50 [0001.543] E> I2C: slave not found in slaves. [0001.543] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start t. [0001.544] E> I2C_DEV: Failed to send register address 0x00000000. [0001.544] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 a. [0001.554] E> eeprom: Retry to read I2C slave device. [0001.558] E> I2C: slave not found in slaves. [0001.562] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start t. [0001.570] E> I2C_DEV: Failed to send register address 0x00000000. [0001.576] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 a. [0001.585] E> eeprom: Failed to read I2C slave device [0001.590] I> Eeprom read failed 0x3526070d [0001.594] I> create_pm_ids: id: 3668-0000-200-H, len: 15 [0001.599] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:03 [0001.610] I> create_pm_ids: id: 3509-0000-100-G, len: 15 [0001.615] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:03 [0001.627] I> Adding plugin-manager/ids/3668-0000-200=/i2c@3160000:module@0x50 [0001.634] W> "i2c@3160000" doesn't exist, creating [0001.638] W> "module@0x50" doesn't exist, creating [0001.643] I> Adding plugin-manager/ids/3509-0000-100=/i2c@3160000:module@0x57 [0001.650] W> "module@0x57" doesn't exist, creating [0001.656] I> Adding plugin-manager/cvm [0001.658] W> "chip-id" doesn't exist, creating [0001.662] I> Adding plugin-manager/chip-id/A02P [0001.667] I> Plugin-manager override starting [0001.672] I> node /plugin-manager/fragment-pcie-c5-rp matches [0001.680] I> node /plugin-manager/fragement-tegra-wdt-en matches [0001.686] I> node /plugin-manager/fragement-tegra-sdhci-emmc-dis matches [0001.694] I> Disable plugin-manager status in FDT [0001.694] I> Plugin-manager override finished successfully [0001.699] I> gpio framework initialized [0001.704] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio' drir [0001.711] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio-aon'r [0001.717] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x46 [0001.725] W> fetch_driver_phandle_from_dt: failed to get node with compatible 9 [0001.733] W> fetch_driver_phandle_from_dt: failed to get node with compatible 9 [0001.739] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0001.745] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x44 [0001.752] W> fetch_driver_phandle_from_dt: failed to get node with compatible 9 [0001.760] W> fetch_driver_phandle_from_dt: failed to get node with compatible 9 [0001.767] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0001.774] I> fixed regulator driver initialized [0001.782] I> register 'maxim' power off handle [0001.783] I> virtual i2c enabled [0001.785] I> registered 'maxim,max20024' pmic [0001.789] I> tegrabl_gpio_driver_register: register 'max20024-gpio' driver [0001.796] I> Boot-device: QSPI [0001.799] I> Boot_device: QSPI_FLASH instance: 0 [0001.804] I> QSPI source rate = 204000 Khz [0001.807] I> Requested rate for QSPI clock = 34000 Khz [0001.812] I> BPMP-set rate for QSPI clk = 34000 Khz [0001.817] I> QSPI Flash Size = 32 MB [0001.825] I> Qspi initialized successfully [0001.825] I> qspi flash-0 params source = boot args [0001.829] I> create_pm_ids: id: 3668-0000-200-H, len: 15 [0001.834] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:03 [0001.845] I> create_pm_ids: id: 3509-0000-100-G, len: 15 [0001.850] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:03 [0001.861] I> No sdcard [0001.863] I> -0 params source = [0001.868] I> Found 47 partitions in QSPI_FLASH (instance 0) [0001.880] I> regulator 'vdd-hdmi-5v0' already enabled [0001.884] I> regulator 'vdd-hdmi-5v0' already enabled [0001.884] E> tegrabl_display_init_regulator: hdmi cable is not connected [0001.888] E> tegrabl_display_get_pdata, failed to parse dtb settings [0001.897] E> invalid display type [0001.899] E> cannot find any other nvdisp nodes [0001.902] E> no valid display unit config found in dtb [0001.908] W> display init failed [0001.910] I> Load in CBoot Boot Options partition and parse it [0001.916] E> Error -9 when finding node with path /boot-configuration [0001.922] E> tegrabl_cbo_parse_info: "boot-configuration" not found in CBO fil. [0001.929] I> Using default boot order [0001.933] I> boot-dev-order :- [0001.936] I> 1.sd [0001.937] I> 2.usb [0001.939] I> 3.nvme [0001.941] I> 4.emmc [0001.943] I> 5.net [0001.945] I> Hit any key to stop autoboot: 4 3 2 1 [0003.953] initializing target [0003.953] calling apps_init() [0003.954] starting app kernel_boot_app [0003.964] I> found decompressor handler: lz4-legacy [0003.965] I> decompressing BMP blob ... [0003.977] I> Kernel type = Normal [0003.977] I> ########## SD (0) boot ########## [0003.978] I> No sdcard [0003.978] I> -0 params source = [0003.978] E> Blockdev open: exit error [0003.978] E> SD boot failed, err: 724238353 [0003.979] I> ########## USB (0) boot ########## [0003.984] W> No valid slot number is found in scratch register [0003.984] W> Return default slot: _a [0003.997] I> Validate XUSB-FW ... [0003.998] I> T19x: Authenticate XUSB-FW (bin_type: 11), max size 0x30000 [0003.999] I> Encryption fuse is not ON [0004.000] I> USB Firmware Version: 60.09 release [0004.058] I> regulator of usb2-0 already enabled [0004.063] I> regulator of usb2-1 already enabled [0004.068] I> regulator of usb2-2 already enabled [0005.135] I> USB 2.0 port 2 new high-speed USB device detected [0005.136] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa42cd5000 [0005.237] I> Start to enumerate device [0005.238] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa42cd5000 [0005.248] I> [0005.248] I> Enumerated USB Device 0bda:5489 [0005.249] I> [0005.251] I> Hub: [0005.251] I> Downstream ports : 4 [0005.251] I> Power switching : Ganged [0005.252] I> Compound device : No [0005.252] I> Over-current protection : Global [0005.252] I> Hub avg delay : 4 ns [0005.254] I> Set interface = 1 (alt setting) [0005.259] I> Enable hub ports [0006.286] E> No device found on any of the hub ports [0006.286] E> failed to start xhci controller [0006.286] E> Error in init of XUSB host driver, err: 7979000d [0006.287] W> Failed to initialize device 5-0 [0006.287] E> USB boot failed, err: 2037973005 [0006.288] I> ########## NVME (0) boot ########## [0006.288] I> Initializing nvme device instance 0 [0006.293] I> Initializing nvme controller [0006.297] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14180000 [0006.303] I> vpcie3v3-supply not found [0006.306] I> vpcie12v-supply not found [0006.310] W> Failed to get nvidia,plat-gpios [0006.314] I> tegrabl_pcie_soc_preinit: (0): [0006.318] I> Unpowergate [0006.321] I> tegrabl_car_clk_disable(0) ... [0006.325] I> tegrabl_car_rst_set(CORE, 0) ... [0006.329] I> tegrabl_car_rst_set(APB, 0) ... [0006.333] I> tegrabl_car_clk_enable(0) ... [0006.337] I> tegrabl_car_rst_clear(APB, 0) ... [0006.341] I> tegrabl_set_ctrl_state(0) [0006.345] I> CLR PCIE_APB:6 [0006.347] I> tegrabl_pcie_soc_init: (0): [0006.351] I> APPL initialization ... [0006.354] I> poweron phys [0006.357] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14180000 [0006.363] I> tegrabl_power_on_phy: controller 0 not available [0006.369] E> Failed to power on phy on controller-0 [0006.374] W> Failed tegrabl_pcie_soc_init(), error=0x1 [0006.379] I> Failed to initialize SoC Host PCIe controller [0006.384] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(0); error=0x1 [0006.390] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800601 [0006.397] W> Failed to open NVME-0, err = 80800601 [0006.401] W> Failed to initialize device 10-0 [0006.406] E> NVME (0) boot failed, err: 0x80800601 [0006.410] I> ########## NVME (1) boot ########## [0006.415] I> Initializing nvme device instance 1 [0006.419] I> Initializing nvme controller [0006.423] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14100000 [0006.429] I> vpcie3v3-supply not found [0006.433] I> vpcie12v-supply not found [0006.437] W> Failed to get nvidia,plat-gpios [0006.441] I> tegrabl_pcie_soc_preinit: (1): [0006.445] I> Unpowergate [0006.447] I> tegrabl_car_clk_disable(1) ... [0006.451] I> tegrabl_car_rst_set(CORE, 1) ... [0006.455] I> tegrabl_car_rst_set(APB, 1) ... [0006.459] I> tegrabl_car_clk_enable(1) ... [0006.463] I> tegrabl_car_rst_clear(APB, 1) ... [0006.468] I> tegrabl_set_ctrl_state(1) [0006.471] I> CLR PCIE_APB:6 [0006.474] I> tegrabl_pcie_soc_init: (1): [0006.478] I> APPL initialization ... [0006.481] I> poweron phys [0006.484] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14100000 [0006.490] I> tegrabl_power_on_phy: controller 1 not available [0006.495] E> Failed to power on phy on controller-1 [0006.500] W> Failed tegrabl_pcie_soc_init(), error=0x1 [0006.505] I> Failed to initialize SoC Host PCIe controller [0006.510] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(1); error=0x1 [0006.517] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800601 [0006.523] W> Failed to open NVME-1, err = 80800601 [0006.528] W> Failed to initialize device 10-1 [0006.532] E> NVME (1) boot failed, err: 0x80800601 [0006.537] I> ########## NVME (2) boot ########## [0006.541] I> Initializing nvme device instance 2 [0006.546] I> Initializing nvme controller [0006.550] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14120000 [0006.556] I> vpcie3v3-supply not found [0006.560] I> vpcie12v-supply not found [0006.563] W> Failed to get nvidia,plat-gpios [0006.567] I> tegrabl_pcie_soc_preinit: (2): [0006.571] I> Unpowergate [0006.574] I> tegrabl_car_clk_disable(2) ... [0006.578] I> tegrabl_car_rst_set(CORE, 2) ... [0006.582] I> tegrabl_car_rst_set(APB, 2) ... [0006.586] I> tegrabl_car_clk_enable(2) ... [0006.590] I> tegrabl_car_rst_clear(APB, 2) ... [0006.594] I> tegrabl_set_ctrl_state(2) [0006.598] I> CLR PCIE_APB:6 [0006.601] I> tegrabl_pcie_soc_init: (2): [0006.604] I> APPL initialization ... [0006.608] I> poweron phys [0006.610] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14120000 [0006.616] I> tegrabl_power_on_phy: controller 2 not available [0006.622] E> Failed to power on phy on controller-2 [0006.627] W> Failed tegrabl_pcie_soc_init(), error=0x1 [0006.632] I> Failed to initialize SoC Host PCIe controller [0006.637] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(2); error=0x1 [0006.643] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800601 [0006.650] W> Failed to open NVME-2, err = 80800601 [0006.655] W> Failed to initialize device 10-2 [0006.659] E> NVME (2) boot failed, err: 0x80800601 [0006.663] I> ########## NVME (3) boot ########## [0006.668] I> Initializing nvme device instance 3 [0006.672] I> Initializing nvme controller [0006.677] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14140000 [0006.683] I> vpcie3v3-supply not found [0006.686] I> vpcie12v-supply not found [0006.690] W> Failed to get nvidia,plat-gpios [0006.694] I> tegrabl_pcie_soc_preinit: (3): [0006.698] I> Unpowergate [0006.700] I> tegrabl_car_clk_disable(3) ... [0006.704] I> tegrabl_car_rst_set(CORE, 3) ... [0006.709] I> tegrabl_car_rst_set(APB, 3) ... [0006.713] I> tegrabl_car_clk_enable(3) ... [0006.717] I> tegrabl_car_rst_clear(APB, 3) ... [0006.721] I> tegrabl_set_ctrl_state(3) [0006.724] I> CLR PCIE_APB:6 [0006.727] I> tegrabl_pcie_soc_init: (3): [0006.731] I> APPL initialization ... [0006.734] I> poweron phys [0006.737] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14140000 [0006.743] I> tegrabl_power_on_phy: controller 3 not available [0006.749] E> Failed to power on phy on controller-3 [0006.754] W> Failed tegrabl_pcie_soc_init(), error=0x1 [0006.758] I> Failed to initialize SoC Host PCIe controller [0006.764] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(3); error=0x1 [0006.770] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800601 [0006.777] W> Failed to open NVME-3, err = 80800601 [0006.781] W> Failed to initialize device 10-3 [0006.785] E> NVME (3) boot failed, err: 0x80800601 [0006.790] I> ########## NVME (4) boot ########## [0006.794] I> Initializing nvme device instance 4 [0006.799] I> Initializing nvme controller [0006.803] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14160000 [0006.809] I> vpcie3v3-supply not found [0006.813] I> vpcie12v-supply not found [0006.816] W> Failed to get nvidia,plat-gpios [0006.820] I> tegrabl_pcie_soc_preinit: (4): [0006.825] I> Unpowergate [0006.827] I> tegrabl_car_clk_disable(4) ... [0006.831] I> tegrabl_car_rst_set(CORE, 4) ... [0006.835] I> tegrabl_car_rst_set(APB, 4) ... [0006.839] I> tegrabl_car_clk_enable(4) ... [0006.843] I> tegrabl_car_rst_clear(APB, 4) ... [0006.847] I> tegrabl_set_ctrl_state(4) [0006.851] I> CLR PCIE_APB:6 [0006.854] I> tegrabl_pcie_soc_init: (4): [0006.857] I> APPL initialization ... [0006.861] I> poweron phys [0006.864] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14160000 [0006.870] I> tegrabl_power_on_phy: power on phy @0x3f40000 [0006.977] I> PCIe controller-4 link is up [0006.977] I> tegra_pcie_info[4].cfg0_base = 0x36000000 [0006.978] I> tegra_pcie_info[4].cfg1_base = 0x36020000 [0006.978] I> tegra_pcie_info[4].atu_dma_base = 0x36040000 [0006.978] I> tegra_pcie_bus[4].mem = 0x36200000 [0006.979] I> Scanning busnr: 0 devfn: 0 [0006.979] I> PCIe IDs: 0x1ad110de [0006.982] I> PCIe RID_CC: 0x60400a1 [0006.986] I> Scanning busnr: 1 devfn: 0 [0006.989] I> PCIe IDs: 0xc82210ec [0006.992] I> PCIe RID_CC: 0x2800000 [0006.996] I> PCI Config: I/O=0x36100000, Memory=0x36200000 [0007.001] I> IO bar_num=0 bar=0x36100000 [0007.005] I> MEM64 bar_num=2 bar=0x36200000 [0007.009] I> Number of PCIe devices detected: 2 [0007.013] E> tegrabl_nvme_init: Failed tegrabl_pcie_get_dev(4); error=0x0 [0007.020] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800612 [0007.026] W> Failed to open NVME-4, err = 80800612 [0007.031] W> Failed to initialize device 10-4 [0007.035] E> NVME (4) boot failed, err: 0x80800612 [0007.040] I> ########## NVME (5) boot ########## [0007.044] I> Initializing nvme device instance 5 [0007.049] I> Initializing nvme controller [0007.053] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x141a0000 [0007.059] I> vpcie3v3-supply not found [0007.063] I> vpcie12v-supply not found [0007.066] W> Failed to get nvidia,plat-gpios [0007.070] I> tegrabl_pcie_soc_preinit: (5): [0007.074] I> Unpowergate [0007.077] I> tegrabl_car_clk_disable(5) ... [0007.081] I> tegrabl_car_rst_set(CORE, 5) ... [0007.085] I> tegrabl_car_rst_set(APB, 5) ... [0007.089] I> tegrabl_car_clk_enable(5) ... [0007.093] I> tegrabl_car_rst_clear(APB, 5) ... [0007.097] I> tegrabl_set_ctrl_state(5) [0007.101] I> CLR PCIE_APB:6 [0007.104] I> tegrabl_pcie_soc_init: (5): [0007.107] I> APPL initialization ... [0007.111] I> poweron phys [0007.114] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x141a0000 [0007.120] I> tegrabl_power_on_phy: power on phy @0x3eb0000 [0007.125] I> tegrabl_power_on_phy: power on phy @0x3ec0000 [0007.130] I> tegrabl_power_on_phy: power on phy @0x3ed0000 [0007.136] I> tegrabl_power_on_phy: power on phy @0x3ee0000 [0007.141] I> tegrabl_power_on_phy: power on phy @0x3ef0000 [0007.146] I> tegrabl_power_on_phy: power on phy @0x3f00000 [0007.152] I> tegrabl_power_on_phy: power on phy @0x3f10000 [0007.157] I> tegrabl_power_on_phy: power on phy @0x3f20000 [0008.262] C> Failed to link up controller-5 [0008.263] W> Failed tegrabl_pcie_soc_init(), error=0x12 [0008.263] I> Failed to initialize SoC Host PCIe controller [0008.264] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(5); error=0x12 [0008.264] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800612 [0008.265] W> Failed to open NVME-5, err = 80800612 [0008.269] W> Failed to initialize device 10-5 [0008.273] E> NVME (5) boot failed, err: 0x80800612 [0008.278] I> ########## Fixed storage boot ########## [0008.283] I> Loading kernel-bootctrl from partition [0008.288] E> Cannot find partition kernel-bootctrl [0008.292] E> Cannot open partition kernel-bootctrl [0008.297] W> tegrabl_get_kernel_bootctrl: failed to read primary bootctrl data [0008.304] I> Loading kernel-bootctrl_b from partition [0008.309] E> Cannot find partition kernel-bootctrl_b [0008.314] E> Cannot open partition kernel-bootctrl_b [0008.319] W> tegrabl_get_kernel_bootctrl: failed to read recovery bootctrl data [0008.326] W> tegrabl_get_kernel_bootctrl: use default dummy boot control data [0008.333] E> Blockdev open: exit error [0008.337] E> tegrabl_display_clear: display is not initialized [0008.342] W> Boot logo display failed... [0008.346] I> Kernel EP: 0x0, DTB: 0x0 [0008.350] [0008.350] ----------------------------------------------- [0008.356] Synchronous Exception: UNKNOWN EXCEPTION [0008.360] ----------------------------------------------- [0008.366] [0008.367] ESR 0x2000000: ec 0x0, il 0x1, iss 0x0 [0008.371] ----------------------------------------------- [0008.376] [Stack Trace] [0008.379] [0008.380] => pc:0x00000000, sp:0xA06A3F30 [0008.384] => pc:0xA060F790, sp:0xA06A4160 [0008.388] => pc:0xA060F7A4, sp:0xA06A41B0 [0008.391] => pc:0xA060F58C, sp:0xA06A41E0 [0008.395] => pc:0xA060EB00, sp:0xA06A41F0 [0008.399] => pc:0xA060EAD4, sp:0xA06A4200 [0008.403] ----------------------------------------------- [0008.408] iframe 0xa06a3e40: [0008.411] x0 0x 0 x1 0x 0 x2 0x 00 [0008.420] x4 0x 0 x5 0x 20 x6 0x b2001230 [0008.429] x8 0x 0 x9 0xffffffffffffffff x10 0x 62 [0008.438] x12 0x 1 x13 0x 40 x14 0x 10 [0008.447] x16 0x 9 x17 0x 1 x18 0x 00 [0008.456] x20 0x 0 x21 0x 0 x22 0x 00 [0008.466] x24 0x 0 x25 0x 0 x26 0x 00 [0008.475] x28 0x 0 x29 0x a06a4160 lr 0x a060f7440 [0008.484] elr 0x 0 [0008.487] spsr 0x 400003c9 [0008.490] ----------------------------------------------- [0008.495] panic (caller 0xa0601238): die [0008.499] HALT: spinning forever...