[10:59:27.784][20211126_10:59:27] [10:59:32.633][0000.261] [L4T TegraBoot] (version 00.00.2018.01-l4t-2d758fea) [10:59:32.633][0000.266] Processing in cold boot mode Bootloader 2 [10:59:32.646][0000.271] A02 Bootrom Patch rev = 1023 [10:59:32.646][0000.274] Power-up reason: pmc por [10:59:32.646][0000.277] No Battery Present [10:59:32.656][0000.280] pmic max77620 reset reason [10:59:32.657][0000.283] pmic max77620 NVERC : 0x50 [10:59:32.657][0000.287] RamCode = 0 [10:59:32.657][0000.289] Platform has DDR4 type RAM [10:59:32.669][0000.292] max77620 disabling SD1 Remote Sense [10:59:32.677][0000.297] Setting DDR voltage to 1125mv [10:59:32.677][0000.301] Serial Number of Pmic Max77663: 0x141af2 [10:59:32.682][0000.308] Entering ramdump check [10:59:32.682][0000.311] Get RamDumpCarveOut = 0x0 [10:59:32.694][0000.315] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [10:59:32.694][0000.320] Last reboot was clean, booting normally! [10:59:32.694][0000.324] Sdram initialization is successful [10:59:32.705][0000.328] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [10:59:32.705][0000.335] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [10:59:32.716][0000.340] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [10:59:32.716][0000.346] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [10:59:32.728][0000.352] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [10:59:32.728][0000.358] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [10:59:32.746][0000.364] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [10:59:32.746][0000.370] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [10:59:32.763][0000.386] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [10:59:32.763][0000.392] Platform-DebugCarveout: 0 [10:59:32.781][0000.395] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [10:59:32.781][0000.401] Non secure mode, and RB not enabled. [10:59:32.782][0000.405] Read GPT from (0:3) [10:59:32.797][0000.420] Csd NumOfBlocks=0 [10:59:32.810][0000.429] Using GPT Primary to query partitions [10:59:32.810][0000.433] Read PT from (0:3) [10:59:32.810][0000.438] Using BFS PT to query partitions [10:59:32.830][0000.442] Loading Tboot-CPU binary [10:59:32.831][0000.448] Verifying TBC in OdmNonSecureSBK mode [10:59:32.842][0000.458] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [10:59:32.842][0000.465] Bootloader downloaded successfully. [10:59:32.853][0000.469] Downloaded Tboot-CPU binary to 0xa0000258 [10:59:32.853][0000.474] MAX77620_GPIO5 configured [10:59:32.854][0000.477] CPU power rail is up [10:59:32.854][0000.480] CPU clock enabled [10:59:32.869][0000.484] Performing RAM repair [10:59:32.870][0000.487] Updating A64 Warmreset Address to 0xa00002e9 [10:59:32.870][0000.492] Loading NvTbootBootloaderDTB [10:59:32.891][0000.509] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [10:59:32.958][0000.574] Bootloader DTB Load Address: 0x83000000 [10:59:32.958][0000.579] Loading NvTbootKernelDTB [10:59:32.979][0000.596] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [10:59:33.046][0000.661] Kernel DTB Load Address: 0x83100000 [10:59:33.046][0000.666] Loading cboot binary [10:59:33.061][0000.677] Verifying EBT in OdmNonSecureSBK mode [10:59:33.104][0000.719] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [10:59:33.104][0000.726] Bootloader downloaded successfully. [10:59:33.115][0000.730] PT: Partition NCT NOT found ! [10:59:33.115][0000.734] Warning: Find Partition via PT Failed [10:59:33.130][0000.738] Next binary entry address: 0x92c00258 [10:59:33.130][0000.743] BoardId: 3448 [10:59:33.130][0000.747] Overriding pmu board id with proc board id [10:59:33.136][0000.752] Display board id is not available [10:59:33.149][0000.764] Verifying SC7EntryFw in OdmNonSecureSBK mode [10:59:33.206][0000.816] /bpmp deleted [10:59:33.206][0000.818] SC7EntryFw header found loaded at 0xff700000 [10:59:33.405][0001.008] OVR2 PMIC [10:59:33.406][0001.010] Bpmp FW successfully loaded [10:59:33.406][0001.015] WB0 init successfully at 0xff780000 [10:59:33.415][0001.019] Set NvDecSticky Bits [10:59:33.415][0001.023] GSC2 address ff53fffc value c0edbbcc [10:59:33.415][0001.029] GSC MC Settings done [10:59:33.432][0001.032] TOS Image length 53680 [10:59:33.432][0001.035] Monitor size 53680 [10:59:33.433][0001.038] OS size 0 [10:59:33.433][0001.043] Secure Os AES-CMAC Verification Success! [10:59:33.447][0001.048] TOS image cipher info: plaintext [10:59:33.447][0001.052] Loading and Validation of Secure OS Successful [10:59:33.461][0001.068] SC7 Entry Firmware - 0xff700000, 0x4000 [10:59:33.461][0001.072] NvTbootPackSdramParams: start. [10:59:33.473][0001.077] NvTbootPackSdramParams: done. [10:59:33.477][0001.081] Tegraboot started after 191108 us [10:59:33.478][0001.085] Basic modules init took 584241 us [10:59:33.487][0001.089] Sec Bootdevice Read Time = 52 ms, Read Size = 3668 KB [10:59:33.488][0001.095] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [10:59:33.499][0001.100] Next stage binary read took 7384 us [10:59:33.500][0001.105] Carveout took -19267 us [10:59:33.501][0001.108] CPU initialization took 344085 us [10:59:33.518][0001.112] Total time taken by TegraBoot 916443 us [10:59:33.518] [10:59:33.519][0001.116] Starting CPU & Halting co-processor [10:59:33.519] [10:59:33.519]64NOTICE: BL31: v1.3(release):fe06da916 [10:59:33.534]NOTICE: BL31: Built : 18:04:17, Apr 8 2020 [10:59:33.534]ERROR: Error initializing runtime service trusty_fast [10:59:33.642][0001.239] RamCode = 0 [10:59:33.643][0001.243] LPDDR4 Training: Read DT: Number of tables = 2 [10:59:33.648][0001.248] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [10:59:33.664][0001.261] EMC Training Successful [10:59:33.664][0001.264] 408000 not found in DVFS table [10:59:33.666][0001.271] RamCode = 0 [10:59:33.679][0001.274] DT Write: emc-table@204000 succeeded [10:59:33.680][0001.279] DT Write: emc-table@1600000 succeeded [10:59:33.694][0001.284] LPDDR4 Training: Write DT: Number of tables = 2 [10:59:33.694][0001.324] [10:59:33.694][0001.325] Debug Init done [10:59:33.694][0001.327] Marked DTB cacheable [10:59:33.696][0001.330] Bootloader DTB loaded at 0x83000000 [10:59:33.709][0001.335] Marked DTB cacheable [10:59:33.710][0001.338] Kernel DTB loaded at 0x83100000 [10:59:33.710][0001.342] DeviceTree Init done [10:59:33.728][0001.358] Pinmux applied successfully [10:59:33.728][0001.362] gicd_base: 0x50041000 [10:59:33.729][0001.365] gicc_base: 0x50042000 [10:59:33.741][0001.368] Interrupts Init done [10:59:33.741][0001.373] Using base:0x60005090 & irq:208 for tick-timer [10:59:33.742][0001.378] Using base:0x60005098 for delay-timer [10:59:33.754][0001.382] platform_init_timer: DONE [10:59:33.754][0001.386] Timer(tick) Init done [10:59:33.755][0001.389] osc freq = 38400 khz [10:59:33.756][0001.394] [10:59:33.767][0001.395] Welcome to L4T Cboot [10:59:33.767][0001.398] [10:59:33.767][0001.399] Cboot Version: 00.00.2018.01-t210-40c3ff9c [10:59:33.768][0001.404] calling constructors [10:59:33.778][0001.407] initializing heap [10:59:33.778][0001.409] initializing threads [10:59:33.779][0001.412] initializing timers [10:59:33.791][0001.415] creating bootstrap completion thread [10:59:33.791][0001.420] top of bootstrap2() [10:59:33.791][0001.422] CPU: ARM Cortex A57 [10:59:33.792][0001.425] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [10:59:33.795][0001.430] initializing platform [10:59:33.854][0001.484] Config for emmc ddr50 mode completed [10:59:33.854][0001.488] sdmmc bdev is already initialized [10:59:33.855][0001.492] Enable APE clock [10:59:33.866][0001.495] Un-powergate APE partition [10:59:33.867][0001.499] of_register: registering tegra_udc to of_hal [10:59:33.878][0001.504] of_register: registering inv20628-driver to of_hal [10:59:33.879][0001.509] of_register: registering ads1015-driver to of_hal [10:59:33.890][0001.515] of_register: registering lp8557-bl-driver to of_hal [10:59:33.891][0001.521] of_register: registering bq2419x_charger to of_hal [10:59:33.895][0001.526] of_register: registering bq27441_fuel_gauge to of_hal [10:59:33.908][0001.538] gpio framework initialized [10:59:33.909][0001.541] of_register: registering tca9539_gpio to of_hal [10:59:33.918][0001.547] of_register: registering tca9539_gpio to of_hal [10:59:33.919][0001.552] of_register: registering i2c_bus_driver to of_hal [10:59:33.930][0001.558] of_register: registering i2c_bus_driver to of_hal [10:59:33.930][0001.563] of_register: registering i2c_bus_driver to of_hal [10:59:33.932][0001.569] pmic framework initialized [10:59:33.941][0001.572] of_register: registering max77620_pmic to of_hal [10:59:33.943][0001.578] regulator framework initialized [10:59:33.957][0001.582] of_register: registering tps65132_bl_driver to of_hal [10:59:33.958][0001.587] initializing target [10:59:33.963][0001.593] gpio_driver_register: register 'tegra_gpio_driver' driver [10:59:33.975][0001.604] fixed regulator driver initialized [10:59:33.992][0001.621] initializing OF layer [10:59:33.992][0001.624] NCK carveout not present [10:59:33.993][0001.628] Skipping dts_overrides [10:59:34.001][0001.632] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [10:59:34.024][0001.649] I2C Bus Init done [10:59:34.025][0001.651] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [10:59:34.035][0001.662] I2C Bus Init done [10:59:34.036][0001.664] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [10:59:34.049][0001.675] I2C Bus Init done [10:59:34.050][0001.677] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [10:59:34.062][0001.688] I2C Bus Init done [10:59:34.062][0001.690] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [10:59:34.063][0001.701] I2C Bus Init done [10:59:34.080][0001.703] of_children_init: Ops found for compatible string maxim,max77620 [10:59:34.081][0001.714] max77620_init using irq 118 [10:59:34.091][0001.719] register 'maxim,max77620' pmic [10:59:34.092][0001.723] gpio_driver_register: register 'max77620-gpio' driver [10:59:34.115][0001.729] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [10:59:34.115][0001.740] I2C Bus Init done [10:59:34.118][0001.743] NCK carveout not present [10:59:34.126][0001.753] Find /i2c@7000c000's alias i2c0 [10:59:34.127][0001.757] get eeprom at 1-a0, size 256, type 0 [10:59:34.135][0001.766] Find /i2c@7000c500's alias i2c2 [10:59:34.136][0001.770] get eeprom at 3-a0, size 256, type 0 [10:59:34.147][0001.774] get eeprom at 3-ae, size 256, type 0 [10:59:34.147][0001.779] pm_ids_update: Updating 1,a0, size 256, type 0 [10:59:34.149][0001.784] I2C slave not started [10:59:34.160][0001.787] I2C write failed [10:59:34.160][0001.790] Writing offset failed [10:59:34.161][0001.793] eeprom_init: EEPROM read failed [10:59:34.171][0001.797] pm_ids_update: eeprom init failed [10:59:34.172][0001.801] pm_ids_update: Updating 3,a0, size 256, type 0 [10:59:34.205][0001.831] pm_ids_update: The pm board id is 3448-0002-400 [10:59:34.218][0001.837] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [10:59:34.218][0001.845] pm_ids_update: pm id update successful [10:59:34.219][0001.850] pm_ids_update: Updating 3,ae, size 256, type 0 [10:59:34.227][0001.855] I2C slave not started [10:59:34.228][0001.858] I2C write failed [10:59:34.229][0001.861] Writing offset failed [10:59:34.236][0001.864] eeprom_init: EEPROM read failed [10:59:34.237][0001.868] pm_ids_update: eeprom init failed [10:59:34.266][0001.898] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [10:59:34.280][0001.904] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [10:59:34.281][0001.912] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [10:59:34.293][0001.918] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [10:59:34.294][0001.927] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e9:e8:8b [10:59:34.303][0001.933] Plugin Manager: Parse ODM data 0x00094000 [10:59:34.326][0001.943] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 [10:59:34.340][0001.968] Find /i2c@7000c000's alias i2c0 [10:59:34.342][0001.971] get eeprom at 1-a0, size 256, type 0 [10:59:34.349][0001.980] Find /i2c@7000c500's alias i2c2 [10:59:34.352][0001.984] get eeprom at 3-a0, size 256, type 0 [10:59:34.361][0001.989] get eeprom at 3-ae, size 256, type 0 [10:59:34.361][0001.993] pm_ids_update: Updating 1,a0, size 256, type 0 [10:59:34.362][0001.998] I2C slave not started [10:59:34.374][0002.001] I2C write failed [10:59:34.374][0002.004] Writing offset failed [10:59:34.375][0002.007] eeprom_init: EEPROM read failed [10:59:34.388][0002.011] pm_ids_update: eeprom init failed [10:59:34.389][0002.015] pm_ids_update: Updating 3,a0, size 256, type 0 [10:59:34.417][0002.045] pm_ids_update: The pm board id is 3448-0002-400 [10:59:34.430][0002.052] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [10:59:34.431][0002.059] pm_ids_update: pm id update successful [10:59:34.433][0002.063] pm_ids_update: Updating 3,ae, size 256, type 0 [10:59:34.441][0002.068] I2C slave not started [10:59:34.441][0002.071] I2C write failed [10:59:34.442][0002.074] Writing offset failed [10:59:34.449][0002.077] eeprom_init: EEPROM read failed [10:59:34.451][0002.081] pm_ids_update: eeprom init failed [10:59:34.486][0002.111] Add serial number:1423119049708 as DT property [10:59:34.487][0002.119] Applying platform configs [10:59:34.497][0002.126] platform-init is not present. Skipping [10:59:34.498][0002.130] calling apps_init() [10:59:34.517][0002.146] Found 17 GPT partitions in "sdmmc3_user" [10:59:34.519][0002.151] Proceeding to Cold Boot [10:59:34.529][0002.154] starting app android_boot_app [10:59:34.529][0002.158] Device state: unlocked [10:59:34.530][0002.161] display console init [10:59:34.542][0002.170] could not find regulator [10:59:34.543][0002.173] hdmi cable connected [10:59:34.556][0002.189] edid read success [10:59:34.577][0002.204] edid rDT entry for leds-pwm not found [10:59:34.578]e[0002.211] ad success [10:59:34.590][0002.214] width = 640, height = 480, frequency = 25174825 [10:59:34.592][0002.219] width = 1024, height = 600, frequency = 49000000 [10:59:34.601][0002.224] width = 1920, height = 1080, frequency = 148500000 [10:59:34.602][0002.230] width = 720, height = 480, frequency = 27000000 [10:59:34.604][0002.235] width = 720, height = 576, frequency = 27000000 [10:59:34.613][0002.241] width = 720, height = 480, frequency = 26973026 [10:59:34.614][0002.246] width = 1280, height = 720, frequency = 74175824 [10:59:34.624][0002.252] width = 1920, height = 1080, frequency = 148351648 [10:59:34.626][0002.257] width = 720, height = 576, frequency = 26973026 [10:59:34.637][0002.263] width = 1280, height = 720, frequency = 74175824 [10:59:34.638][0002.268] width = 1920, height = 1080, frequency = 148351648 [10:59:34.651][0002.274] Best mode Width = 1920, Height = 1080, freq = 148351648 [10:59:34.652][0002.282] tmds-config node not found [10:59:34.660][0002.286] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [10:59:34.675][0002.300] setting 'vdd-1v8' regulator to 1800000 micro volts [10:59:34.675][0002.308] could not find regulator [10:59:34.676][0002.311] could not find regulator [10:59:34.681][0002.315] could not find regulator [10:59:34.713][0002.343] using default cmu settings [10:59:34.714][0002.346] dc_hdmi_enable, starting HDMI initialisation [10:59:34.728][0002.353] dc_hdmi_enable, HDMI initialisation complete [10:59:34.729][0002.358] list and configure display window [10:59:34.734][0002.366] display console init completed [10:59:34.746][0002.378] subnode volume_up is not found ! [10:59:34.747][0002.381] subnode back is not found ! [10:59:34.762][0002.385] subnode volume_down is not found ! [10:59:34.762][0002.389] subnode menu is not found ! [10:59:34.765][0002.393] Gpio keyboard init success [10:59:34.808][0002.440] found decompressor handler: lz4-legacy [10:59:34.821][0002.454] decompressing blob (type 1)... [10:59:34.856][0002.487] load_bmp_blob: panelresolution=1080 type=3 [10:59:34.906][0002.537] decompressor handler not found [10:59:34.907][0002.541] load_firmware_blob: Firmware blob loaded, entries=2 [10:59:34.918][0002.547] -------> se_aes_verify_sbk_clear: 747 [10:59:34.921][0002.551] se_aes_verify_sbk_clear: Error [10:59:34.937][0002.555] bl_battery_charging: connected to external power supply [10:59:34.937][0002.562] xusb is supported [10:59:34.938][0002.568] error while finding nvidia,portmap [10:59:35.446][0003.073] xusb blob version 0 size 124416 [10:59:35.447][0003.076] firmware size 124416 [10:59:35.452][0003.081] Firmware timestamp: 0x5da88fc3, Version: 50.25 release [10:59:35.465][0003.095] xhci0: 64 bytes context size, 32-bit DMA [10:59:35.503][0003.135] usbus0: 5.0Gbps Super Speed USB v3.0 [10:59:35.527][0003.155] uhub0: on usbus0 [10:59:36.175][0003.805] uhub0: 9 ports with 9 removable, self powered [10:59:37.179][0004.805] failed to get HID devices [10:59:37.180][0004.809] failed to init xhci or no usb device attached [10:59:37.201][0004.822] device_query_partition_size: failed to open partition sdmmc3_user:MSC ! [10:59:37.202][0004.830] MSC Partition not found [10:59:37.209][0004.839] device_query_partition_size: failed to open partition sdmmc3_user:USP ! [10:59:37.210][0004.847] USP partition read failed! [10:59:37.220][0004.850] blob_init: blob-partition USP header read failed [10:59:37.221][0004.856] android_boot Unable to update recovery partition [10:59:37.236][0004.861] kfs_getpartname: name = LNX [10:59:37.238][0004.865] Loading kernel from LNX [10:59:37.298][0004.928] load kernel from storage [10:59:37.304][0004.937] decompressor handler not found [10:59:37.334][0004.957] Successfully loaded kernel and ramdisk images [10:59:37.334][0004.963] load_bmp_blob: panelresolution=1080 type=3 [10:59:37.830][0005.461] display bmp image done [10:59:37.830][0005.464] NCK carveout not present [10:59:37.831][0005.467] Skipping dts_overrides [10:59:37.838][0005.470] NCK carveout not present [10:59:37.857][0005.480] Find /i2c@7000c000's alias i2c0 [10:59:37.858][0005.484] get eeprom at 1-a0, size 256, type 0 [10:59:37.862][0005.493] Find /i2c@7000c500's alias i2c2 [10:59:37.863][0005.497] get eeprom at 3-a0, size 256, type 0 [10:59:37.875][0005.502] get eeprom at 3-ae, size 256, type 0 [10:59:37.875][0005.506] pm_ids_update: Updating 1,a0, size 256, type 0 [10:59:37.876][0005.511] I2C slave not started [10:59:37.886][0005.514] I2C write failed [10:59:37.886][0005.517] Writing offset failed [10:59:37.887][0005.520] eeprom_init: EEPROM read failed [10:59:37.901][0005.524] pm_ids_update: eeprom init failed [10:59:37.902][0005.528] pm_ids_update: Updating 3,a0, size 256, type 0 [10:59:37.931][0005.558] pm_ids_update: The pm board id is 3448-0002-400 [10:59:37.945][0005.565] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [10:59:37.945][0005.573] pm_ids_update: pm id update successful [10:59:37.946][0005.577] pm_ids_update: Updating 3,ae, size 256, type 0 [10:59:37.955][0005.583] I2C slave not started [10:59:37.955][0005.585] I2C write failed [10:59:37.956][0005.588] Writing offset failed [10:59:37.977][0005.591] eeprom_init: EEPROM read failed [10:59:37.978][0005.595] pm_ids_update: eeprom init failed [10:59:37.994][0005.625] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [10:59:38.006][0005.631] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [10:59:38.007][0005.639] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [10:59:38.021][0005.645] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [10:59:38.022][0005.654] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e9:e8:8b [10:59:38.038][0005.660] Plugin Manager: Parse ODM data 0x00094000 [10:59:38.050][0005.670] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 [10:59:38.070][0005.688] Add serial number:1423119049708 as DT property [10:59:38.070][0005.697] "bpmp" doesn't exist, creating [10:59:38.071][0005.703] Updated bpmp info to DTB [10:59:38.082][0005.708] Updated initrd info to DTB [10:59:38.082][0005.711] "proc-board" doesn't exist, creating [10:59:38.083][0005.717] Updated board info to DTB [10:59:38.096][0005.720] "pmu-board" doesn't exist, creating [10:59:38.096][0005.725] Updated board info to DTB [10:59:38.098][0005.729] "display-board" doesn't exist, creating [10:59:38.105][0005.735] Updated board info to DTB [10:59:38.105][0005.738] "reset" doesn't exist, creating [10:59:38.106][0005.742] Updated reset info to DTB [10:59:38.126][0005.746] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 tegra_fbmem=0x800000@0x92cb0000 is_hdmi_initialised=1 [10:59:38.163][0005.785] DTB cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 [10:59:38.188][0005.800] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 [10:59:38.188][0005.816] Updated bootarg info to DTB [10:59:38.189][0005.820] Adding uuid 00000001644577861400000015060200 to DT [10:59:38.206][0005.826] Adding eks info 0 to DT [10:59:38.207][0005.831] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [10:59:38.208][0005.837] Updated memory info to DTB [10:59:38.232][0005.846] set vdd_core voltage to 1075 mv [10:59:38.234][0005.850] setting 'vdd-core' regulator to 1075000 micro volts [10:59:38.245][0005.875] Found secure-pmc; disable BPMP [10:59:38.323] [10:59:38.323] [10:59:38.323]U-Boot 2016.07 (Sep 25 2020 - 12:43:24 +0800) [10:59:38.323] [10:59:38.323]TEGRA210 [10:59:38.323]Model: NVIDIA P3450-Porg [10:59:38.324]Board: NVIDIA P3450-PORG [10:59:38.484]DRAM: 4 GiB [10:59:38.596]MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 [10:59:38.596]*** Warning - spi_flash_probe() failed, using default environment [10:59:38.596] [10:59:38.597]In: serial [10:59:38.608]Out: serial [10:59:38.608]Err: serial [10:59:38.609]Net: No ethernet found. [10:59:38.625]Card did not respond to voltage select! [10:59:38.626]** Bad device mmc 1 ** [10:59:38.626]Hit any key to stop autoboot: 0 [10:59:38.637]Card did not respond to voltage select! [10:59:38.716]switch to partitions #0, OK [10:59:38.716]mmc0(part 0) is current device [10:59:39.416]Scanning mmc 0:1... [10:59:39.938]Found /boot/extlinux/extlinux.conf [10:59:39.939]Retrieving file: /boot/extlinux/extlinux.conf [10:59:40.037]795 bytes read in 74 ms (9.8 KiB/s) [10:59:40.037]1: primary kernel [10:59:40.039]Retrieving file: /boot/initrd [10:59:40.283]5487746 bytes read in 229 ms (22.9 MiB/s) [10:59:40.284]Retrieving file: /boot/Image [10:59:41.118]34854920 bytes read in 820 ms (40.5 MiB/s) [10:59:41.140]append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 tegra_fbmem=0x800000@0x92cb0000 is_hdmi_initialised=1 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 quiet loglevel=0 vt.global_cursor_default=0 console=tty1 fbcon=map:1 [10:59:41.188]## Flattened Device Tree blob at 83100000 [10:59:41.198] Booting using the fdt blob at 0x83100000 [10:59:41.199] reserving fdt memory region: addr=80000000 size=20000 [10:59:41.207] Using Device Tree in place at 0000000083100000, end 00000000831777fb [10:59:41.217] [10:59:41.217]Starting kernel ... [10:59:41.220] [10:59:44.929][ 3.229077] using random self ethernet address [10:59:44.951][ 3.249344] using random host ethernet address [10:59:45.077][ 3.371236] FAT-fs (loop0): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [10:59:45.165][ 3.457705] random: crng init done [10:59:45.166][ 3.461118] random: 7 urandom warning(s) missed due to ratelimiting [10:59:45.182][ 3.479115] dvrs_hw: loading out-of-tree module taints kernel. [10:59:45.593][ 3.884969] using random self ethernet address [10:59:45.594][ 3.889728] using random host ethernet address [10:59:45.914][ 4.215013] tegra_cec 70015000.tegra_cec: timeout in tegra_cec_native_write_l:172. [10:59:45.935][ 4.223223] tegra_cec 70015000.tegra_cec: Sent res: -62. [10:59:45.936][ 4.230078] tegra_cec 70015000.tegra_cec: tegra_cec_init Done. [10:59:48.673][ 6.968184] scsi 0:0:0:0: Direct-Access Generic STORAGE DEVICE 1532 PQ: 0 ANSI: 6 [10:59:48.967][ 7.267514] ------------[ cut here ]------------ [10:59:48.982][ 7.272138] WARNING: CPU: 0 PID: 0 at kernel/irq/handle.c:149 __handle_irq_event_percpu+0x238/0x288 [10:59:48.983][ 7.281282] ---[ end trace ee99213fb1d91a50 ]--- [10:59:49.010][ 7.310215] sd 0:0:0:0: [sda] 124735488 512-byte logical blocks: (63.9 GB/59.5 GiB) [10:59:49.030][ 7.318653] sd 0:0:0:0: [sda] Write Protect is off [10:59:49.031][ 7.324066] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [10:59:49.045][ 7.343000] sd 0:0:0:0: [sda] Attached SCSI removable disk [10:59:50.786] [10:59:50.799]Ubuntu 18.04.4 LTS linux ttyS0 [10:59:50.799] [10:59:50.810]linux login: root (automatic login) [10:59:50.811] [10:59:50.828]Last login: Fri Nov 26 10:57:35 CST 2021 on ttyS0 [10:59:51.304]Welcome to Ubuntu 18.04.4 LTS (GNU/Linux 4.9.140-tegra aarch64) [10:59:51.304] [10:59:51.305] * Documentation: https://help.ubuntu.com [10:59:51.314] * Management: https://landscape.canonical.com [10:59:51.314] * Support: https://ubuntu.com/advantage [10:59:51.315] [10:59:51.325]This system has been minimized by removing packages and content that are [10:59:51.326]not required on a system that users do not log into. [10:59:51.327] [10:59:51.336]To restore this content, you can run the 'unminimize' command. [10:59:51.336] [10:59:51.336]414 packages can be updated. [10:59:51.337]297 updates are security updates. [10:59:51.337] [10:59:51.353]Failed to connect to https://changelogs.ubuntu.com/meta-release-lts. Check your Internet connection or proxy settings [10:59:51.354] [11:00:01.728]root@linux:~# demsg --follow [11:00:01.744]-bash: demsg: command not found [11:00:15.185]root@linux:~# dmesg --follow [11:00:15.208][ 0.000000] Booting Linux on physical CPU 0x0 [11:00:15.232][ 0.000000] Linux version 4.9.140-tegra (cuiep@cuiep-ubuntu) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #10 SMP PREEMPT Thu Sep 24 16:30:31 CST 2020 [11:00:15.234][ 0.000000] Boot CPU: AArch64 Processor [411fd071] [11:00:15.243][ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 48, [11:00:15.243][ 0.000000] OF: fdt: - 80000000 , 7ee00000 [11:00:15.244][ 0.000000] OF: fdt: - 100000000 , 7f200000 [11:00:15.251][ 0.000000] Found tegra_fbmem: 00800000@92cb0000 [11:00:15.264][ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [11:00:15.274][ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [11:00:15.286][ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [11:00:15.296][ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [11:00:15.309][ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [11:00:15.310][ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [11:00:15.317][ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [11:00:15.332][ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [11:00:15.332][ 0.000000] On node 0 totalpages: 1039872 [11:00:15.333][ 0.000000] DMA zone: 8192 pages used for memmap [11:00:15.343][ 0.000000] DMA zone: 0 pages reserved [11:00:15.344][ 0.000000] DMA zone: 519168 pages, LIFO batch:31 [11:00:15.355][ 0.000000] Normal zone: 8136 pages used for memmap [11:00:15.356][ 0.000000] Normal zone: 520704 pages, LIFO batch:31 [11:00:15.365][ 0.000000] psci: probing for conduit method from DT. [11:00:15.365][ 0.000000] psci: PSCIv1.0 detected in firmware. [11:00:15.367][ 0.000000] psci: Using standard PSCI v0.2 function IDs [11:00:15.376][ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [11:00:15.377][ 0.000000] psci: SMC Calling Convention v1.1 [11:00:15.385][ 0.000000] percpu: Embedded 25 pages/cpu @ffffffc0fefb1000 s61656 r8192 d32552 u102400 [11:00:15.398][ 0.000000] pcpu-alloc: s61656 r8192 d32552 u102400 alloc=25*4096 [11:00:15.398][ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [11:00:15.408][ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [11:00:15.409][ 0.000000] Speculative Store Bypass Disable mitigation not required [11:00:15.419][ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [11:00:15.439][ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 tegra_fbmem=0x800000@0x92cb0000 is_hdmi_initialised=1 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 quiet loglevel=0 vt.global_cursor_default=0 console=tty1 fbcon=map:1 [11:00:15.496][ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [11:00:15.497][ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [11:00:15.508][ 0.000000] log_buf_len min size: 32768 bytes [11:00:15.508][ 0.000000] log_buf_len: 131072 bytes [11:00:15.511][ 0.000000] early log buf free: 29268(89%) [11:00:15.517][ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [11:00:15.532][ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [11:00:15.533][ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [11:00:15.541][ 0.000000] Memory: 3561576K/4159488K available (15294K kernel code, 2934K rwdata, 6596K rodata, 9152K init, 609K bss, 122776K reserved, 475136K cma-reserved) [11:00:15.555][ 0.000000] Virtual kernel memory layout: [11:00:15.556][ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [11:00:15.562][ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [11:00:15.575][ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f70000 ( 15296 KB) [11:00:15.576][ 0.000000] .rodata : 0xffffff8008f70000 - 0xffffff80095f0000 ( 6656 KB) [11:00:15.585][ 0.000000] .init : 0xffffff80095f0000 - 0xffffff8009ee0000 ( 9152 KB) [11:00:15.597][ 0.000000] .data : 0xffffff8009ee0000 - 0xffffff800a1bd808 ( 2935 KB) [11:00:15.598][ 0.000000] .bss : 0xffffff800a1bd808 - 0xffffff800a255f3c ( 610 KB) [11:00:15.608][ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [11:00:15.619][ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [11:00:15.620][ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [11:00:15.630][ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [11:00:15.643][ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [11:00:15.644][ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [11:00:15.654][ 0.000000] Preemptible hierarchical RCU implementation. [11:00:15.655][ 0.000000] Build-time adjustment of leaf fanout to 64. [11:00:15.664][ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [11:00:15.676][ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [11:00:15.677][ 0.000000] NR_IRQS:64 nr_irqs:64 0 [11:00:15.687][ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [11:00:15.687][ 0.000000] t210 clock and reset probe [11:00:15.688][ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [11:00:15.697][ 0.000000] clk_cbus_recalc_rate: no gbus parent [11:00:15.699][ 0.000000] clk_cbus_recalc_rate: no gbus parent [11:00:15.709][ 0.000000] clk_cbus_recalc_rate: no gbus parent [11:00:15.710][ 0.000000] clk_cbus_recalc_rate: no gbus parent [11:00:15.720][ 0.000000] clk_cbus_recalc_rate: no gbus parent [11:00:15.721][ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [11:00:15.730][ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [11:00:15.743][ 0.000007] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [11:00:15.744][ 0.001779] Console: colour dummy device 80x25 [11:00:15.752][ 0.001799] console [tty0] enabled [11:00:15.753][ 0.001816] kmemleak: Kernel memory leak detector disabled [11:00:15.764][ 0.001835] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [11:00:15.765][ 0.001848] pid_max: default: 32768 minimum: 301 [11:00:15.775][ 0.002304] Security Framework initialized [11:00:15.778][ 0.002532] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [11:00:15.784][ 0.002540] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [11:00:15.798][ 0.003704] ftrace: allocating 47094 entries in 184 pages [11:00:15.798][ 0.175906] sched-energy: CPU device node has no sched-energy-costs [11:00:15.807][ 0.175943] ASID allocator initialised with 65536 entries [11:00:15.808][ 0.212381] tegra-id: chipid=22117. [11:00:15.808][ 0.212394] tegra-id: opt_subrevision=0. [11:00:15.819][ 0.212412] Tegra Speedo/IDDQ fuse revision 4 [11:00:15.820][ 0.212417] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2 [11:00:15.828][ 0.212422] Tegra: CPU Process ID 0, SoC Process ID 1, GPU Process ID 0 [11:00:15.840][ 0.212429] Tegra: CPU Speedo Value 2113, SoC Speedo Value 1995, GPU Speedo Value 2106 [11:00:15.841][ 0.212433] Tegra: CPU IDDQ Value 2240, SoC IDDQ Value 2412, GPU IDDQ Value 2975 [11:00:15.850][ 0.212451] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 1 [11:00:15.863][ 0.212466] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0002-p3449-0000-b00.dts [11:00:15.876][ 0.212472] DTB Build time: Apr 8 2020 18:15:58 [11:00:15.877][ 0.261112] CPU1: Booted secondary processor [411fd071] [11:00:15.887][ 0.293013] CPU2: Booted secondary processor [411fd071] [11:00:15.887][ 0.324990] CPU3: Booted secondary processor [411fd071] [11:00:15.888][ 0.325080] Brought up 4 CPUs [11:00:15.898][ 0.325087] SMP: Total of 4 processors activated. [11:00:15.899][ 0.325097] CPU features: detected feature: 32-bit EL0 Support [11:00:15.907][ 0.325362] CPU: All CPU(s) started at EL2 [11:00:15.908][ 0.325380] alternatives: patching kernel code [11:00:15.909][ 0.333827] devtmpfs: initialized [11:00:15.919][ 0.371801] Initilizing CustomIPI irq domain [11:00:15.932][ 0.372191] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [11:00:15.933][ 0.372212] futex hash table entries: 1024 (order: 4, 65536 bytes) [11:00:15.940][ 0.383688] pinctrl core: initialized pinctrl subsystem [11:00:15.940][ 0.384375] OS set in device tree is not L4T. [11:00:15.941][ 0.384811] regulator-dummy: no parameters [11:00:15.952][ 0.385159] Initializing plugin-manager [11:00:15.953][ 0.385270] Plugin module not found [11:00:15.964][ 0.385506] node /plugin-manager/fragement@0 match with board >=3448-0002-100 [11:00:15.965][ 0.386073] node /plugin-manager/fragment@1 match with board >=3448-0002-101 [11:00:15.973][ 0.386569] node /plugin-manager/fragment@3 match with board >=3448-0002-100 [11:00:15.985][ 0.387266] node /plugin-manager/fragement@6 match with odm-data enable-tegra-wdt [11:00:15.987][ 0.387704] node /plugin-manager/fragement@8 match with odm-data enable-tegra-wdt [11:00:15.996][ 0.388343] node /plugin-manager/fragement@10 match with board >=3448-0002-300 [11:00:16.009][ 0.390513] node /plugin-manager/fragement@11 match with board >=3448-0002-300 [11:00:16.009][ 0.394070] NET: Registered protocol family 16 [11:00:16.011][ 0.395503] pstore: using zlib compression [11:00:16.019][ 0.395537] console [pstore-1] enabled [11:00:16.020][ 0.395542] pstore: Registered ramoops as persistent store backend [11:00:16.030][ 0.395547] ramoops: attached 0x200000@0xb0000000, ecc: 0/0 [11:00:16.032][ 0.409133] cpuidle: using governor menu [11:00:16.041][ 0.413452] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver [11:00:16.042][ 0.415345] vdso: 2 pages (1 code @ ffffff8008f77000, 1 data @ ffffff8009ee4000) [11:00:16.050][ 0.415369] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [11:00:16.063][ 0.417729] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations [11:00:16.063][ 0.419968] Serial: AMBA PL011 UART driver [11:00:16.064][ 0.420472] tegra_powergate_init: DONE [11:00:16.088][ 0.420489] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0002-p3449-0000-b00.dts [11:00:16.089][ 0.420495] DTB Build time: Apr 8 2020 18:15:58 [11:00:16.096][ 0.422408] Tegra reboot handler registered. [11:00:16.097][ 0.427054] iommu: Adding device tegra-carveouts to group 0 [11:00:16.106][ 0.427198] platform tegra-carveouts: domain=ffffffc0f94243d8 allocates as[0]=ffffffc0f94080a8 [11:00:16.118][ 0.427559] iommu: Adding device smmu_test to group 1 [11:00:16.119][ 0.427604] platform smmu_test: domain=ffffffc0f9424618 allocates as[0]=ffffffc0f9408110 [11:00:16.130][ 0.428431] mc: mapped MMIO address: 0xffffff800802e000 -> 0x70019000 [11:00:16.132][ 0.428484] mc: mapped MMIO address: 0xffffff8008065000 -> 0x7001c000 [11:00:16.140][ 0.428547] mc: mapped MMIO address: 0xffffff8008079000 -> 0x7001d000 [11:00:16.151][ 0.428556] nv-tegra-mc 70019000.mc: No mssnvlink node [11:00:16.152][ 0.428576] mc-err: mcerr ops are set to t21x [11:00:16.152][ 0.438457] iommu: Adding device 70090000.xusb to group 2 [11:00:16.161][ 0.438741] iommu: Adding device 70006000.serial to group 3 [11:00:16.173][ 0.438818] platform 70006000.serial: domain=ffffffc0f94b66d8 allocates as[0]=ffffffc0f9408178 [11:00:16.174][ 0.439247] iommu: Adding device 70006040.serial to group 4 [11:00:16.185][ 0.439516] iommu: Adding device 70006200.serial to group 5 [11:00:16.186][ 0.439745] iommu: Adding device sound to group 6 [11:00:16.197][ 0.439792] platform sound: domain=ffffffc0f94b6c18 allocates as[0]=ffffffc0f94081e0 [11:00:16.198][ 0.440360] iommu: Adding device 7000d400.spi to group 7 [11:00:16.208][ 0.440634] iommu: Adding device 7000d600.spi to group 8 [11:00:16.210][ 0.440969] iommu: Adding device 50000000.host1x to group 9 [11:00:16.219][ 0.441355] iommu: Adding device 54080000.vi to group 10 [11:00:16.220][ 0.441758] iommu: Adding device 54600000.isp to group 11 [11:00:16.230][ 0.442015] iommu: Adding device 54680000.isp to group 12 [11:00:16.231][ 0.442288] iommu: Adding device tegradc.0 to group 13 [11:00:16.240][ 0.442366] platform tegradc.0: domain=ffffffc0f94c39d8 allocates as[0]=ffffffc0f9408248 [11:00:16.242][ 0.446558] platform tegradc.0: IOVA linear map 0x0000000092cb0000(800000) [11:00:16.252][ 0.446951] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000) [11:00:16.263][ 0.447298] iommu: Adding device tegradc.1 to group 14 [11:00:16.264][ 0.447345] platform tegradc.1: domain=ffffffc0f94c3c18 allocates as[0]=ffffffc0f94082b0 [11:00:16.272][ 0.451607] platform tegradc.1: IOVA linear map 0x0000000092cb0000(800000) [11:00:16.286][ 0.451997] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000) [11:00:16.288][ 0.452258] iommu: Adding device 54340000.vic to group 15 [11:00:16.295][ 0.452459] iommu: Adding device 544c0000.nvenc to group 16 [11:00:16.296][ 0.452661] iommu: Adding device 54500000.tsec to group 17 [11:00:16.307][ 0.452875] iommu: Adding device 54100000.tsecb to group 18 [11:00:16.308][ 0.453111] iommu: Adding device 54480000.nvdec to group 19 [11:00:16.319][ 0.453305] iommu: Adding device 54380000.nvjpg to group 20 [11:00:16.319][ 0.454385] iommu: Adding device 546c0000.i2c to group 21 [11:00:16.320][ 0.454727] iommu: Adding device 57000000.gpu to group 22 [11:00:16.327][ 0.454781] platform 57000000.gpu: domain=ffffffc0f94d1c18 allocates as[0]=ffffffc0f9408318 [11:00:16.339][ 0.454820] platform 57000000.gpu: domain=ffffffc0f94d1c18 allocates as[1]=ffffffc0f9408380 [11:00:16.352][ 0.454861] platform 57000000.gpu: domain=ffffffc0f94d1c18 allocates as[2]=ffffffc0f94083e8 [11:00:16.355][ 0.454902] platform 57000000.gpu: domain=ffffffc0f94d1c18 allocates as[3]=ffffffc0f9408450 [11:00:16.360][ 0.455822] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [11:00:16.373][ 0.455833] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present [11:00:16.374][ 0.455844] tegra-pmc: ### PMC reset source: TEGRA_POWER_ON_RESET [11:00:16.386][ 0.455849] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM [11:00:16.387][ 0.455852] tegra-pmc: ### PMC reset status reg: 0x0 [11:00:16.394][ 0.505180] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [11:00:16.408][ 0.505190] tegra-pmc: Clear bootloader IO dpd settings [11:00:16.409][ 0.505211] tegra-pmc 7000e400.pmc: IO padctrl driver initialized [11:00:16.417][ 0.505281] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands [11:00:16.418][ 0.505577] iommu: Adding device 70012000.se to group 23 [11:00:16.429][ 0.506438] iommu: Adding device 7000c000.i2c to group 24 [11:00:16.430][ 0.506696] iommu: Adding device 7000c400.i2c to group 25 [11:00:16.440][ 0.507004] iommu: Adding device 7000c500.i2c to group 26 [11:00:16.441][ 0.507313] iommu: Adding device 7000c700.i2c to group 27 [11:00:16.452][ 0.507611] iommu: Adding device 7000d000.i2c to group 28 [11:00:16.453][ 0.507940] iommu: Adding device 7000d100.i2c to group 29 [11:00:16.462][ 0.508258] iommu: Adding device sdhci-tegra.3 to group 30 [11:00:16.463][ 0.508314] platform sdhci-tegra.3: domain=ffffffc0f955be58 allocates as[0]=ffffffc0f94084b8 [11:00:16.473][ 0.509315] iommu: Adding device 700d0000.xudc to group 31 [11:00:16.474][ 0.513508] vdd-ac-bat: 5000 mV [11:00:16.484][ 0.513909] vdd-5v0-sys: 5000 mV [11:00:16.484][ 0.514990] vdd-5v0-hdmi: supplied by vdd-5v0-sys [11:00:16.486][ 0.515061] vdd-5v0-hdmi: 5000 mV [11:00:16.495][ 0.515535] vdd-1v8-sys: 1800 mV [11:00:16.495][ 0.515984] vdd-fan: supplied by vdd-5v0-sys [11:00:16.496][ 0.516021] vdd-fan: 5000 mV [11:00:16.507][ 0.516470] vdd-usb-vbus: supplied by vdd-5v0-sys [11:00:16.507][ 0.516530] vdd-usb-vbus: 5000 mV [11:00:16.509][ 0.517186] vdd-usb-vbus2: 5000 mV [11:00:16.517][ 0.550297] HugeTLB registered 2 MB page size, pre-allocated 0 pages [11:00:16.531][ 0.552804] gpio gpiochip0: gpio-line-names specifies 240 line names but there are 256 lines on the chip [11:00:16.534][ 0.554062] GPIO line 151 (camera-control-output-low) hogged as output/low [11:00:16.547][ 0.554084] GPIO line 152 (camera-control-output-low) hogged as output/low [11:00:16.549][ 0.554116] GPIO line 6 (system-suspend-gpio) hogged as output/high [11:00:16.556][ 0.554710] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio) [11:00:16.563][ 0.562683] eventlib_kernel: keventlib is initialized, test id: 0 [11:00:16.563][ 0.563038] SCSI subsystem initialized [11:00:16.564][ 0.563269] libata version 3.00 loaded. [11:00:16.574][ 0.563567] usbcore: registered new interface driver usbfs [11:00:16.576][ 0.563619] usbcore: registered new interface driver hub [11:00:16.584][ 0.563704] usbcore: registered new device driver usb [11:00:16.585][ 0.567769] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8 [11:00:16.595][ 0.572376] vdd-core: 600 <--> 1162 mV at 1075 mV [11:00:16.596][ 0.572539] random: fast init done [11:00:16.606][ 0.573450] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV [11:00:16.606][ 0.577105] vdd-ddr-1v1: 1150 mV [11:00:16.607][ 0.581008] vdd-pre-reg-1v35: 1350 mV [11:00:16.619][ 0.585007] vdd-1v8: 1800 mV [11:00:16.619][ 0.589015] avdd-sys-1v2: 1200 mV [11:00:16.620][ 0.593011] vdd-pex-1v0: 1050 mV [11:00:16.628][ 0.593696] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV [11:00:16.628][ 0.594234] max77620-ldo3: at 3100 mV [11:00:16.629][ 0.597015] vdd-rtc: 850 <--> 1100 mV at 1000 mV [11:00:16.639][ 0.597554] max77620-ldo5: at 3100 mV [11:00:16.641][ 0.601014] vddio-sdmmc3-ap: 1800 <--> 3300 mV at 2800 mV [11:00:16.650][ 0.605010] avdd-1v05-pll: 1050 mV [11:00:16.653][ 0.609007] avdd-io-hdmi-dp: 1050 mV [11:00:16.661][ 0.611666] GPIO line 505 (spmic-default-output-high) hogged as output/high [11:00:16.663][ 0.611944] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio) [11:00:16.672][ 0.612230] max77620 4-003c: max77620 probe successful [11:00:16.673][ 0.614956] media: Linux media interface: v0.10 [11:00:16.683][ 0.615017] Linux video capture interface: v2.00 [11:00:16.685][ 0.615967] pps_core: LinuxPPS API ver. 1 registered [11:00:16.696][ 0.615974] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [11:00:16.697][ 0.615998] PTP clock support registered [11:00:16.706][ 0.619278] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table [11:00:16.708][ 0.620112] Advanced Linux Sound Architecture Driver Initialized. [11:00:16.717][ 0.620877] Bluetooth: Core ver 2.22 [11:00:16.719][ 0.620929] NET: Registered protocol family 31 [11:00:16.728][ 0.620932] Bluetooth: HCI device and connection manager initialized [11:00:16.729][ 0.620950] Bluetooth: HCI socket layer initialized [11:00:16.739][ 0.620959] Bluetooth: L2CAP socket layer initialized [11:00:16.740][ 0.621013] Bluetooth: SCO socket layer initialized [11:00:16.751][ 0.622774] tegra210_dvfs: no clock found for sdmmc2_ddr [11:00:16.752][ 0.622789] tegra210_dvfs: no clock found for sdmmc4_ddr [11:00:16.761][ 0.622834] tegra210_dvfs: no clock found for sdmmc1_ddr [11:00:16.762][ 0.622848] tegra210_dvfs: no clock found for sdmmc3_ddr [11:00:16.773][ 0.626611] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe [11:00:16.773][ 0.627866] vdd-3v3-sys: supplied by vdd-5v0-sys [11:00:16.774][ 0.627937] vdd-3v3-sys: 3300 mV [11:00:16.783][ 0.628227] vdd-1v8-sys: supplied by vdd-3v3-sys [11:00:16.785][ 0.633215] vdd-usb-vbus2: supplied by vdd-3v3-sys [11:00:16.794][ 0.633714] vdd-3v3-sd: supplied by vdd-3v3-sys [11:00:16.794][ 0.633788] vdd-3v3-sd: 3300 mV [11:00:16.795][ 0.634870] avdd-io-edp-1v05: supplied by avdd-1v05-pll [11:00:16.806][ 0.634914] avdd-io-edp-1v05: 1050 mV [11:00:16.806][ 0.635341] vdd-usb-hub-en: supplied by vdd-1v8-sys [11:00:16.807][ 0.635379] vdd-usb-hub-en: 5000 mV [11:00:16.815][ 0.636817] camchar: rtcpu character device driver loaded [11:00:16.827][ 0.637534] extcon-gpio-states extcon:extcon@1: Cable state:0, cable id:0 [11:00:16.827][ 0.638954] clocksource: Switched to clocksource arch_sys_counter [11:00:16.829][ 0.680603] VFS: Disk quotas dquot_6.6.0 [11:00:16.837][ 0.680738] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [11:00:16.848][ 0.681226] nvmap_heap_init: nvmap_heap_init: created heap block cache [11:00:16.861][ 0.681660] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000 [11:00:16.873][ 0.681678] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000) [11:00:16.874][ 0.681881] cma: enabled page replacement for spfn=d7000, epfn=f0000 [11:00:16.884][ 0.681886] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful [11:00:16.894][ 0.681899] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout [11:00:16.906][ 0.681926] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048 [11:00:16.907][ 0.681932] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout [11:00:16.917][ 0.681947] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways [11:00:16.918][ 0.681955] nvmap_page_pool_init: Total RAM pages: 1009178 [11:00:16.927][ 0.681961] nvmap_page_pool_init: nvmap page pool size: 126147 pages (492 MB) [11:00:16.939][ 0.682048] nvmap_background_zero_thread: PP zeroing thread starting. [11:00:16.940][ 0.682554] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB) [11:00:16.949][ 0.683724] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB) [11:00:16.961][ 0.691947] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm [11:00:16.962][ 0.692372] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm [11:00:16.971][ 0.692614] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm [11:00:16.983][ 0.692820] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [11:00:16.994][ 0.692993] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die [11:00:16.995][ 0.693257] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz [11:00:17.005][ 0.693260] pre_t19x_iso_plat_init(): max_iso_bw=11520000KB [11:00:17.007][ 0.693700] NET: Registered protocol family 2 [11:00:17.016][ 0.694680] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [11:00:17.018][ 0.694892] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [11:00:17.028][ 0.695460] TCP: Hash tables configured (established 32768 bind 32768) [11:00:17.030][ 0.695611] UDP hash table entries: 2048 (order: 4, 65536 bytes) [11:00:17.038][ 0.695697] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [11:00:17.040][ 0.696114] NET: Registered protocol family 1 [11:00:17.051][ 0.696828] RPC: Registered named UNIX socket transport module. [11:00:17.054][ 0.696833] RPC: Registered udp transport module. [11:00:17.067][ 0.696836] RPC: Registered tcp transport module. [11:00:17.070][ 0.696840] RPC: Registered tcp NFSv4.1 backchannel transport module. [11:00:17.083][ 0.696855] PCI: CLS 0 bytes, default 64 [11:00:17.085][ 0.697083] Trying to unpack rootfs image as initramfs... [11:00:17.093][ 0.931828] Freeing initrd memory: 5356K [11:00:17.094][ 0.941976] host1x 50000000.host1x: initialized [11:00:17.100][ 0.943951] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [11:00:17.102][ 0.947204] audit: initializing netlink subsys (disabled) [11:00:17.110][ 0.947275] audit: type=2000 audit(0.795:1): initialized [11:00:17.112][ 0.948060] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [11:00:17.117][ 0.958111] squashfs: version 4.0 (2009/01/31) Phillip Lougher [11:00:17.119][ 0.959647] ntfs: driver 2.1.32 [Flags: R/W]. [11:00:17.127][ 0.960436] 9p: Installing v9fs 9p2000 file system support [11:00:17.129][ 0.963799] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240) [11:00:17.138][ 0.963945] io scheduler noop registered [11:00:17.139][ 0.964263] io scheduler cfq registered (default) [11:00:17.149][ 0.967212] gic 702f9000.agic: GIC IRQ controller registered [11:00:17.150][ 0.970215] iommu: Adding device 702ef000.adsp to group 32 [11:00:17.160][ 0.979352] iommu: Adding device aconnect@702c0000:adsp_audio to group 33 [11:00:17.163][ 0.979530] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered [11:00:17.170][ 0.980139] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x8229411 [11:00:17.182][ 0.980148] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4 [11:00:17.194][ 0.981757] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb [11:00:17.195][ 0.981867] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb [11:00:17.203][ 0.981961] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb [11:00:17.214][ 0.982163] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1 [11:00:17.226][ 0.982249] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4 [11:00:17.237][ 0.982343] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4 [11:00:17.250][ 0.982430] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4 [11:00:17.252][ 0.982523] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4 [11:00:17.259][ 0.982614] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb [11:00:17.270][ 0.982705] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb [11:00:17.283][ 0.988985] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops [11:00:17.284][ 0.990746] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000 [11:00:17.294][ 0.992735] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [11:00:17.295][ 0.994020] tegra-pcie 1003000.pcie: PCIE: Enable power rails [11:00:17.303][ 0.994391] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [11:00:17.317][ 0.995737] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [11:00:17.319][ 0.995975] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=1500000, max_bw=1500000 [11:00:17.327][ 0.996244] Adding domain tsec-pd to PM domain host1x-pd [11:00:17.338][ 0.998600] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [11:00:17.338][ 0.999633] tsec 54500000.tsec: initialized [11:00:17.339][ 1.001227] tsec 54100000.tsecb: initialized [11:00:17.350][ 1.001949] Adding domain nvdec-pd to PM domain host1x-pd [11:00:17.351][ 1.005547] nvdec 54480000.nvdec: initialized [11:00:17.360][ 1.006591] Adding domain vic03-pd to PM domain host1x-pd [11:00:17.361][ 1.006774] Adding domain msenc-pd to PM domain host1x-pd [11:00:17.371][ 1.006977] Adding domain nvjpg-pd to PM domain host1x-pd [11:00:17.371][ 1.011222] falcon 54340000.vic: initialized [11:00:17.372][ 1.012497] falcon 544c0000.nvenc: initialized [11:00:17.383][ 1.013852] falcon 54380000.nvjpg: initialized [11:00:17.386][ 1.018271] tegra_cec 70015000.tegra_cec: dt=1 start=0x70015000 end=0x70015FFF irq=96 [11:00:17.392][ 1.018320] tegra_cec 70015000.tegra_cec: Enable clock result: 0. [11:00:17.405][ 1.018351] tegra_cec 70015000.tegra_cec: tegra_cec_init started [11:00:17.406][ 1.018519] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1 [11:00:17.417][ 1.018664] display board info: id 0x0, fab 0x0 [11:00:17.417][ 1.018686] tegra_cec 70015000.tegra_cec: cec_add_sysfs ret=0 [11:00:17.419][ 1.018691] tegra_cec 70015000.tegra_cec: probed [11:00:17.427][ 1.018744] generic_infoframe_type: 0x87 [11:00:17.428][ 1.018912] tegradc tegradc.0: DT parsed successfully [11:00:17.437][ 1.019005] tegradc tegradc.0: Display dc.ffffff800ac00000 registered with id=0 [11:00:17.449][ 1.019623] tegradc tegradc.0: Bootloader disp_param detected. Detected mode: 1920x1080 (on 0x0mm) pclk=148350781 [11:00:17.449][ 1.022868] tegradc tegradc.0: probed [11:00:17.459][ 1.028838] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [11:00:17.471][ 1.035507] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 22 channels [11:00:17.473][ 1.036479] tegra-fuse-burn 7000f800.efuse:efuse-burn: shutdown limit check disabled [11:00:17.482][ 1.036488] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized [11:00:17.484][ 1.036845] kfuse 7000fc00.kfuse: initialized [11:00:17.493][ 1.038506] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available [11:00:17.505][ 1.039457] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0 [11:00:17.506][ 1.042286] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [11:00:17.517][ 1.042305] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [11:00:17.519][ 1.042311] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [11:00:17.526][ 1.042316] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [11:00:17.538][ 1.042325] pci_bus 0000:00: root bus resource [bus 00-ff] [11:00:17.541][ 1.042392] pci 0000:00:01.0: [10de:0fae] type 01 class 0x060400 [11:00:17.550][ 1.042566] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [11:00:17.553][ 1.042742] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now [11:00:17.561][ 1.042767] vdd-cpu: 708 <--> 1322 mV at 708 mV [11:00:17.562][ 1.043016] pci 0000:00:02.0: [10de:0faf] type 01 class 0x060400 [11:00:17.570][ 1.043122] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold [11:00:17.583][ 1.043377] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [11:00:17.584][ 1.043381] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed [11:00:17.593][ 1.043395] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring [11:00:17.606][ 1.043790] pci 0000:01:00.0: [8888:6141] type 00 class 0x040000 [11:00:17.608][ 1.043840] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0000ffff] [11:00:17.618][ 1.045289] vdd-gpu: applied init 1000000uV constraint [11:00:17.621][ 1.045299] vdd-gpu: 708 <--> 1323 mV at 997 mV [11:00:17.630][ 1.045781] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed [11:00:17.632][ 1.050716] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [11:00:17.638][ 1.050813] No Device Node present for smmu client: serial8250 !! [11:00:17.650][ 1.050823] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [11:00:17.650][ 1.050865] iommu: Adding device serial8250 to group 34 [11:00:17.652][ 1.053317] console [ttyS0] disabled [11:00:17.659][ 1.053401] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra [11:00:17.671][ 1.053495] console [ttyS0] enabled [11:00:17.672][ 1.054505] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART [11:00:17.681][ 1.054846] serial-tegra 70006200.serial: RX in PIO mode [11:00:17.693][ 1.054987] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART [11:00:17.695][ 1.055064] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [11:00:17.704][ 1.055170] tegradc tegradc.0: fb registered [11:00:17.705][ 1.055377] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000 [11:00:17.715][ 1.055414] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x00ff] [11:00:17.717][ 1.055451] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit pref] [11:00:17.728][ 1.055476] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [11:00:17.729][ 1.055655] pci 0000:02:00.0: supports D1 D2 [11:00:17.737][ 1.055661] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [11:00:17.738][ 1.056713] [drm] Initialized [11:00:17.747][ 1.063037] tegradc tegradc.0: DC initialized, skipping tegra_dc_program_mode. [11:00:17.760][ 1.063093] tegradc tegradc.0: hdmi: tmds rate:148351K prod-setting:prod_c_hdmi_75m_150m [11:00:17.761][ 1.063657] tegradc tegradc.0: hdmi: get RGB quant from REG programmed by BL. [11:00:17.771][ 1.063670] tegradc tegradc.0: hdmi: get YCC quant from REG programmed by BL. [11:00:17.773][ 1.067107] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [11:00:17.781][ 1.067198] pci 0000:00:01.0: BAR 14: assigned [mem 0x13000000-0x130fffff] [11:00:17.795][ 1.067208] pci 0000:00:02.0: BAR 15: assigned [mem 0x20000000-0x200fffff 64bit pref] [11:00:17.796][ 1.067214] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff] [11:00:17.806][ 1.067225] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x1300ffff] [11:00:17.807][ 1.067239] pci 0000:00:01.0: PCI bridge to [bus 01] [11:00:17.814][ 1.067249] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [11:00:17.827][ 1.067262] pci 0000:02:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] [11:00:17.828][ 1.067283] pci 0000:02:00.0: BAR 2: assigned [mem 0x20004000-0x20004fff 64bit pref] [11:00:17.837][ 1.067302] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [11:00:17.838][ 1.067311] pci 0000:00:02.0: PCI bridge to [bus 02] [11:00:17.848][ 1.067317] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [11:00:17.860][ 1.067325] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] [11:00:17.861][ 1.067784] pcieport 0000:00:01.0: Signaling PME through PCIe PME interrupt [11:00:17.871][ 1.067790] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [11:00:17.874][ 1.067799] pcie_pme 0000:00:01.0:pcie001: service driver pcie_pme loaded [11:00:17.880][ 1.067940] aer 0000:00:01.0:pcie002: service driver aer loaded [11:00:17.894][ 1.068162] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt [11:00:17.895][ 1.068167] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt [11:00:17.905][ 1.068174] pcie_pme 0000:00:02.0:pcie001: service driver pcie_pme loaded [11:00:17.906][ 1.068287] aer 0000:00:02.0:pcie002: service driver aer loaded [11:00:17.918][ 1.070070] brd: module loaded [11:00:17.918][ 1.075583] loop: module loaded [11:00:17.920][ 1.075696] tegra_profiler: version: 1.141, samples/io: 48/28 [11:00:17.927][ 1.075814] tegra_profiler: auth: init [11:00:17.927][ 1.077255] THERMAL EST: found 2 subdevs [11:00:17.928][ 1.077266] THERMAL EST num_resources: 0 [11:00:17.938][ 1.077272] [THERMAL EST subdev 0] [11:00:17.939][ 1.077281] [THERMAL EST subdev 1] [11:00:17.950][ 1.077812] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est [11:00:17.951][ 1.077817] THERMAL EST: thz register success. [11:00:17.959][ 1.077958] THERMAL EST: end of probe, return err: 0 [11:00:17.960][ 1.079524] sd: No Scsi addr parsed to reserve index [11:00:17.971][ 1.079569] hisi_sas: driver version v1.6 [11:00:17.971][ 1.086419] libphy: Fixed MDIO Bus: probed [11:00:17.972][ 1.087355] tun: Universal TUN/TAP device driver, 1.6 [11:00:17.982][ 1.087363] tun: (C) 1999-2004 Max Krasnyansky [11:00:17.983][ 1.088558] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [11:00:17.992][ 1.088566] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [11:00:18.004][ 1.088624] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [11:00:18.005][ 1.088628] igb: Copyright (c) 2007-2014 Intel Corporation. [11:00:18.016][ 1.088679] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [11:00:18.017][ 1.088683] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [11:00:18.027][ 1.088732] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4 [11:00:18.028][ 1.088738] Copyright(c) 1999 - 2017 Intel Corporation. [11:00:18.038][ 1.089814] r8168 0000:02:00.0: enabling device (0000 -> 0003) [11:00:18.039][ 1.089845] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded [11:00:18.048][ 1.090388] extcon-disp-state extcon:disp-state: cable 47 state 1 [11:00:18.049][ 1.090395] Extcon AUX1(HDMI) enable [11:00:18.059][ 1.091510] tegradc tegradc.1: disp1 connected to head1->/host1x/sor [11:00:18.060][ 1.091591] tegradc tegradc.1: No lt-data, using default setting [11:00:18.071][ 1.091618] tegradc tegradc.1: No hpd-gpio in DT [11:00:18.073][ 1.091650] tegradc tegradc.1: DT parsed successfully [11:00:18.082][ 1.091709] tegradc tegradc.1: Display dc.ffffff800d580000 registered with id=1 [11:00:18.083][ 1.093216] tegradc tegradc.1: dpd enable lookup fail:-19 [11:00:18.104][ 1.111759] r8168 0000:02:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node [11:00:18.115][ 1.111944] r8168 0000:02:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 00:04:4b:e9:e8:8b from device tree [11:00:18.129][ 1.112606] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [11:00:18.131][ 1.112670] r8168 Copyright (C) 2017 Realtek NIC software team [11:00:18.138] This program comes with ABSOLUTELY NO WARRANTY; for details, please see . [11:00:18.148] This is free software, and you are welcome to redistribute it under certain conditions; see . [11:00:18.162][ 1.113539] PPP generic driver version 2.4.2 [11:00:18.165][ 1.113732] PPP BSD Compression module registered [11:00:18.172][ 1.113738] PPP Deflate Compression module registered [11:00:18.172][ 1.113781] PPP MPPE Compression module registered [11:00:18.174][ 1.113789] NET: Registered protocol family 24 [11:00:18.183][ 1.113863] usbcore: registered new interface driver r8152 [11:00:18.185][ 1.113917] usbcore: registered new interface driver asix [11:00:18.192][ 1.113994] usbcore: registered new interface driver ax88179_178a [11:00:18.204][ 1.114033] usbcore: registered new interface driver cdc_ether [11:00:18.205][ 1.114073] usbcore: registered new interface driver net1080 [11:00:18.216][ 1.114116] usbcore: registered new interface driver cdc_subset [11:00:18.218][ 1.114163] usbcore: registered new interface driver zaurus [11:00:18.226][ 1.114223] usbcore: registered new interface driver cdc_ncm [11:00:18.226][ 1.114438] VFIO - User Level meta-driver version: 0.3 [11:00:18.227][ 1.115043] tegradc tegradc.1: probed [11:00:18.238][ 1.123431] Console: switching to colour frame buffer device 80x30 [11:00:18.239][ 1.123471] tegradc tegradc.1: fb registered [11:00:18.249][ 1.124990] tegradc tegradc.0: nominal-pclk:148351648 parent:148350781 div:1.0 pclk:148350781 146868084~161703244 [11:00:18.261][ 1.126215] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [11:00:18.262][ 1.126227] ehci-pci: EHCI PCI platform driver [11:00:18.271][ 1.126263] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [11:00:18.272][ 1.126270] ohci-pci: OHCI PCI platform driver [11:00:18.282][ 1.126302] ohci-platform: OHCI generic platform driver [11:00:18.284][ 1.126680] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_evt 1 [11:00:18.292][ 1.126685] hpd: switching from state 7 (Takeover from bootloader) to state 0 (Reset) [11:00:18.293][ 1.126693] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0 [11:00:18.303][ 1.126704] tegradc tegradc.1: blank - powerdown [11:00:18.314][ 1.126749] extcon-disp-state extcon:disp-state: cable 44 state 0 already set. [11:00:18.315][ 1.126752] Extcon DP: HPD disabled [11:00:18.315][ 1.126755] hpd: hpd_switch 0 [11:00:18.326][ 1.126759] hpd: switching from state 0 (Reset) to state 1 (Check Plug) [11:00:18.327][ 1.126769] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0 [11:00:18.337][ 1.126776] hpd: switching from state 1 (Check Plug) to state 3 (Disabled) [11:00:18.339][ 1.128460] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP [11:00:18.346][ 1.129001] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0 [11:00:18.358][ 1.130045] tegra-xusb 70090000.xusb: extcon 0: ffffffc0f9bbb400 id [11:00:18.359][ 1.131603] usbcore: registered new interface driver uas [11:00:18.370][ 1.131654] usbcore: registered new interface driver usb-storage [11:00:18.371][ 1.131735] usbcore: registered new interface driver usbserial [11:00:18.383][ 1.132489] tegra-xusb 70090000.xusb: Firmware timestamp: 2019-10-17 15:58:59 UTC, Version: 50.25 release [11:00:18.384][ 1.132520] tegra-xusb 70090000.xusb: xHCI Host Controller [11:00:18.391][ 1.132538] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1 [11:00:18.404][ 1.133253] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010 [11:00:18.405][ 1.133287] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000 [11:00:18.414][ 1.133446] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [11:00:18.425][ 1.133452] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [11:00:18.426][ 1.133458] usb usb1: Product: xHCI Host Controller [11:00:18.437][ 1.133462] usb usb1: Manufacturer: Linux 4.9.140-tegra xhci-hcd [11:00:18.437][ 1.133467] usb usb1: SerialNumber: 70090000.xusb [11:00:18.438][ 1.133886] hub 1-0:1.0: USB hub found [11:00:18.447][ 1.133923] hub 1-0:1.0: 5 ports detected [11:00:18.448][ 1.134491] tegra-xusb 70090000.xusb: xHCI Host Controller [11:00:18.458][ 1.134502] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2 [11:00:18.470][ 1.134611] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [11:00:18.471][ 1.134707] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [11:00:18.481][ 1.134712] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [11:00:18.482][ 1.134717] usb usb2: Product: xHCI Host Controller [11:00:18.492][ 1.134721] usb usb2: Manufacturer: Linux 4.9.140-tegra xhci-hcd [11:00:18.494][ 1.134725] usb usb2: SerialNumber: 70090000.xusb [11:00:18.502][ 1.135171] hub 2-0:1.0: USB hub found [11:00:18.504][ 1.135250] hub 2-0:1.0: 4 ports detected [11:00:18.514][ 1.136363] tegra-xudc-new 700d0000.xudc: device count: 1 [11:00:18.516][ 1.137295] tegra-xudc-new 700d0000.xudc: USB charger detection disabled [11:00:18.525][ 1.137305] tegra-xudc-new 700d0000.xudc: vbus state: 0 [11:00:18.526][ 1.137328] tegra-xudc-new 700d0000.xudc: entering ELPG [11:00:18.537][ 1.137547] tegra-xudc-new 700d0000.xudc: entering ELPG done [11:00:18.538][ 1.138009] mousedev: PS/2 mouse device common for all mice [11:00:18.548][ 1.138071] usbcore: registered new interface driver xpad [11:00:18.549][ 1.222412] tegradc tegradc.0: blank - powerdown [11:00:18.559][ 1.235014] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1 [11:00:18.559][ 1.263074] extcon-disp-state extcon:disp-state: cable 47 state 0 [11:00:18.561][ 1.263076] Extcon AUX1(HDMI) disable [11:00:18.571][ 1.267522] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [11:00:18.572][ 1.269607] rtc rtc1: alarm rtc device [11:00:18.580][ 1.269618] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [11:00:18.595][ 1.269634] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [11:00:18.596][ 1.269990] i2c /dev entries driver [11:00:18.597][ 1.271687] i2c i2c-6: Added multiplexed i2c bus 7 [11:00:18.606][ 1.272101] i2c i2c-6: Added multiplexed i2c bus 8 [11:00:18.608][ 1.272106] i2c-mux-gpio cam_i2cmux: 2 port mux on Tegra I2C adapter adapter [11:00:18.615][ 1.272767] imx219 7-0010: tegracam sensor driver:imx219_v2.0.6 [11:00:18.616][ 1.283880] tegradc tegradc.0: unblank [11:00:18.626][ 1.297918] imx219 8-0010: tegracam sensor driver:imx219_v2.0.6 [11:00:18.628][ 1.321194] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [11:00:18.636][ 1.321280] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121) [11:00:18.648][ 1.321310] imx219 8-0010: board setup failed [11:00:18.649][ 1.321406] imx219: probe of 8-0010 failed with error -121 [11:00:18.659][ 1.323146] max77620-power max77620-power: Event recorder REG_NVERC : 0x0 [11:00:18.660][ 1.325672] tegradc tegradc.0: nominal-pclk:49000000 parent:48999316 div:1.0 pclk:48999316 48510000~53410000 [11:00:18.670][ 1.325758] tegradc tegradc.0: hdmi: tmds rate:49000K prod-setting:prod_c_hdmi_0m_54m [11:00:18.682][ 1.326092] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2 [11:00:18.684][ 1.326097] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4 [11:00:18.693][ 1.326555] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [11:00:18.703][ 1.326571] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC [11:00:18.713][ 1.326581] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC [11:00:18.725][ 1.326716] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [11:00:18.736][ 1.326726] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC [11:00:18.738][ 1.326732] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC [11:00:18.746][ 1.326887] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [11:00:18.757][ 1.326897] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC [11:00:18.770][ 1.326902] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature [11:00:18.772][ 1.327093] tegradc tegradc.0: hdmi: get RGB quant from EDID. [11:00:18.781][ 1.327110] tegradc tegradc.0: hdmi: get YCC quant from EDID. [11:00:18.782][ 1.327160] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19 [11:00:18.792][ 1.328060] tegra_aotag tegra-aotag: Registering sensor 0 [11:00:18.793][ 1.328117] tegra_aotag tegra-aotag: Invalid temp readout [11:00:18.803][ 1.328143] tegra_aotag tegra-aotag: Invalid temp readout [11:00:18.805][ 1.328159] tegra_aotag tegra-aotag: Bound to TZ : ID 0 [11:00:18.814][ 1.328168] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0 [11:00:18.826][ 1.329269] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [11:00:18.828][ 1.329288] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered [11:00:18.836][ 1.329518] tegra_aotag tegra-aotag: Invalid temp readout [11:00:18.848][ 1.329550] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered [11:00:18.848][ 1.330046] parse_throttle_dt_data: Num cap clks = 6 [11:00:18.851][ 1.330052] parse_throttle_dt_data: clk=cclk_g type=2 [11:00:18.858][ 1.330065] parse_throttle_dt_data: clk=gpu type=4 [11:00:18.859][ 1.330090] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0 [11:00:18.868][ 1.330110] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0 [11:00:18.880][ 1.330131] parse_throttle_dt_data: clk=cap.throttle.sclk type=0 [11:00:18.881][ 1.330134] parse_throttle_dt_data: clk=emc type=3 [11:00:18.891][ 1.330627] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [11:00:18.904][ 1.330788] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [11:00:18.904][ 1.330998] tegra_throttle_probe: probe successful. #cdevs=4 [11:00:18.905][ 1.331879] FAN dev name: pwm-fan [11:00:18.916][ 1.331964] FAN:gpio request success. [11:00:18.918][ 1.332041] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255 [11:00:18.924][ 1.332363] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal [11:00:18.925][ 1.332531] pwm_fan_driver pwm-fan: fan tach request irq success [11:00:18.936][ 1.332540] pwm_fan_driver pwm-fan: tach period: 1000 [11:00:18.946][ 1.332637] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2 [11:00:18.948][ 1.332642] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2 [11:00:18.956][ 1.332647] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2 [11:00:18.969][ 1.332651] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2 [11:00:18.970][ 1.332655] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3 [11:00:18.980][ 1.332658] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3 [11:00:18.992][ 1.332662] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3 [11:00:18.993][ 1.332666] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4 [11:00:19.000][ 1.332670] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4 [11:00:19.013][ 1.332674] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4 [11:00:19.025][ 1.333545] tegra-wdt 60005100.watchdog: Tegra WDT enabled on probe. Timeout = 120 seconds. [11:00:19.026][ 1.334002] tegra-wdt 60005100.watchdog: initialized (timeout = 120 sec, nowayout = 1) [11:00:19.037][ 1.335021] device-mapper: uevent: version 1.0.3 [11:00:19.040][ 1.335551] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [11:00:19.046][ 1.340765] tegra210-cpufreq cpufreq: probe()...completed [11:00:19.058][ 1.341542] sdhci: Secure Digital Host Controller Interface driver [11:00:19.059][ 1.341543] sdhci: Copyright(c) Pierre Ossman [11:00:19.059][ 1.341545] sdhci-pltfm: SDHCI platform and OF driver helper [11:00:19.068][ 1.341902] sdhci-tegra sdhci-tegra.3: Client registration for eMC Successful [11:00:19.081][ 1.348947] tegra-se 70012000.se: tegra_se_probe: complete [11:00:19.082][ 1.349451] hidraw: raw HID events driver (C) Jiri Kosina [11:00:19.091][ 1.350611] usbcore: registered new interface driver usbhid [11:00:19.092][ 1.350613] usbhid: USB HID core driver [11:00:19.093][ 1.352686] tegra21x_actmon 6000c800.actmon: in actmon_register()... [11:00:19.103][ 1.352850] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all [11:00:19.115][ 1.354572] nvpmodel: initialized successfully [11:00:19.116][ 1.355564] usbcore: registered new interface driver snd-usb-audio [11:00:19.124][ 1.355616] No Device Node present for smmu client: snd-soc-dummy !! [11:00:19.136][ 1.355620] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [11:00:19.137][ 1.355637] iommu: Adding device snd-soc-dummy to group 35 [11:00:19.148][ 1.361950] extcon-disp-state extcon:disp-state: cable 47 state 1 [11:00:19.148][ 1.361952] Extcon AUX1(HDMI) enable [11:00:19.149][ 1.362327] tegradc tegradc.0: sync windows ret = 250 [11:00:19.158][ 1.362385] extcon-disp-state extcon:disp-state: cable 51 state 1 [11:00:19.159][ 1.362387] Extcon HDMI: HPD enabled [11:00:19.172][ 1.362398] tegradc tegradc.0: hdmi: plugged [11:00:19.172][ 1.368362] OPE platform probe [11:00:19.173][ 1.368451] OPE platform probe successful [11:00:19.181][ 1.368480] OPE platform probe [11:00:19.182][ 1.368561] OPE platform probe successful [11:00:19.192][ 1.375683] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input0 [11:00:19.193][ 1.383045] mmc0: SDHCI controller on sdhci-tegra.3 [sdhci-tegra.3] using ADMA 64-bit with 64 bit addr [11:00:19.206][ 1.391539] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok [11:00:19.208][ 1.391660] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok [11:00:19.215][ 1.391780] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok [11:00:19.227][ 1.391899] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok [11:00:19.229][ 1.392015] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok [11:00:19.239][ 1.392137] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok [11:00:19.242][ 1.392251] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok [11:00:19.250][ 1.392368] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok [11:00:19.252][ 1.392551] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok [11:00:19.258][ 1.392671] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok [11:00:19.258][ 1.404094] u32 classifier [11:00:19.260][ 1.404097] Actions configured [11:00:19.270][ 1.404167] Initializing XFRM netlink socket [11:00:19.270][ 1.404868] NET: Registered protocol family 10 [11:00:19.272][ 1.405582] NET: Registered protocol family 17 [11:00:19.279][ 1.405594] NET: Registered protocol family 15 [11:00:19.292][ 1.405668] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [11:00:19.293][ 1.405716] Bluetooth: RFCOMM socket layer initialized [11:00:19.303][ 1.405726] Bluetooth: RFCOMM ver 1.11 [11:00:19.304][ 1.405731] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [11:00:19.314][ 1.405746] Bluetooth: HIDP socket layer initialized [11:00:19.315][ 1.405764] 9pnet: Installing 9P2000 support [11:00:19.316][ 1.405800] Key type dns_resolver registered [11:00:19.324][ 1.406224] Registered cp15_barrier emulation handler [11:00:19.326][ 1.406231] Registered setend emulation handler [11:00:19.335][ 1.407320] registered taskstats version 1 [11:00:19.337][ 1.407949] Adding domain ve2-pd to PM domain host1x-pd [11:00:19.346][ 1.408186] Adding domain ve-pd to PM domain host1x-pd [11:00:19.346][ 1.410221] isp 54600000.isp: initialized [11:00:19.347][ 1.411166] isp 54680000.isp: initialized [11:00:19.357][ 1.421325] last reset is due to power on reset [11:00:19.357][ 1.421329] KERNEL: PMC reset status reg: 0x0 [11:00:19.358][ 1.421406] BL: PMC reset status reg: 0x0 [11:00:19.368][ 1.421408] BL: PMIC poweroff Event Recorder: 0x50 [11:00:19.370][ 1.422861] clk_cbus_recalc_rate: no gbus parent [11:00:19.381][ 1.422867] clk_cbus_round_rate: no gbus parent [11:00:19.382][ 1.422870] clk_cbus_round_rate: no gbus parent [11:00:19.390][ 1.422878] clk_cbus_recalc_rate: no gbus parent [11:00:19.391][ 1.422999] clk_cbus_recalc_rate: no gbus parent [11:00:19.392][ 1.423003] clk_cbus_round_rate: no gbus parent [11:00:19.403][ 1.423005] clk_cbus_round_rate: no gbus parent [11:00:19.405][ 1.423009] clk_cbus_recalc_rate: no gbus parent [11:00:19.413][ 1.423670] tegra_dvfs: GPU-cap: registered [11:00:19.414][ 1.423723] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled [11:00:19.422][ 1.423726] tegra dvfs: vdd-core: nominal 1075mV, offset 600000uV, step 12500uV, scaling enabled [11:00:19.437][ 1.423728] tegra dvfs: vdd-gpu: nominal 1048mV, offset 708000uV, step 10000uV, scaling enabled [11:00:19.438][ 1.425100] tegra_dvfs: vdd-gpu-vts: registered [11:00:19.446][ 1.425758] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered [11:00:19.456][ 1.426298] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered [11:00:19.458][ 1.426806] input: gpio-keys as /devices/gpio-keys/input/input1 [11:00:19.468][ 1.434246] mmc0: new HS400 Enhanced strobe MMC card at address 0001 [11:00:19.470][ 1.434579] mmcblk0: mmc0:0001 DG4016 14.7 GiB [11:00:19.479][ 1.438723] mmcblk0boot0: mmc0:0001 DG4016 partition 1 4.00 MiB [11:00:19.492][ 1.442995] mmcblk0boot1: mmc0:0001 DG4016 partition 2 4.00 MiB [11:00:19.494][ 1.447252] mmcblk0rpmb: mmc0:0001 DG4016 partition 3 4.00 MiB [11:00:19.502][ 1.448233] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 [11:00:19.504][ 1.458972] usb 1-2: new high-speed USB device number 2 using tegra-xusb [11:00:19.513][ 1.459617] tegra_rtc 7000e000.rtc: setting system clock to 2021-11-26 02:59:43 UTC (1637895583) [11:00:19.514][ 1.461012] vi 54080000.vi: vi_probe: ++ [11:00:19.525][ 1.463386] vi 54080000.vi: initialized [11:00:19.526][ 1.465305] vi 54080000.vi: subdev nvcsi--2 bound [11:00:19.536][ 1.465320] vi 54080000.vi: subdev imx219 7-0010 bound [11:00:19.538][ 1.465958] vi 54080000.vi: subdev nvcsi--1 bound [11:00:19.549][ 1.466186] mmcblk mmc0:0001: Card claimed for testing. [11:00:19.549][ 1.467522] Disable partitions left on by BL [11:00:19.551][ 1.467525] disb [11:00:19.557][ 1.467575] bwmgr: missing cdev-type property [11:00:19.559][ 1.467669] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [11:00:19.569][ 1.467676] DRAM derating cdev registered. [11:00:19.569][ 1.468706] vdd-fan: disabling [11:00:19.570][ 1.468709] vdd-usb-vbus: disabling [11:00:19.580][ 1.468712] vdd-usb-vbus2: disabling [11:00:19.580][ 1.468720] vddio-sdmmc-ap: disabling [11:00:19.582][ 1.468804] vddio-sdmmc3-ap: disabling [11:00:19.590][ 1.468868] vdd-3v3-sd: disabling [11:00:19.591][ 1.468872] avdd-io-edp-1v05: disabling [11:00:19.592][ 1.468874] vdd-usb-hub-en: disabling [11:00:19.602][ 1.468953] ALSA device list: [11:00:19.603][ 1.468956] #0: tegra-hda at 0x70038000 irq 82 [11:00:19.604][ 1.468959] #1: tegra-snd-t210ref-mobile-rt565x [11:00:19.614][ 1.472182] Freeing unused kernel memory: 9152K [11:00:19.615][ 1.481882] usb 1-2: New USB device found, idVendor=05e3, idProduct=0610 [11:00:19.625][ 1.481887] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [11:00:19.626][ 1.481890] usb 1-2: Product: USB2.1 Hub [11:00:19.636][ 1.481893] usb 1-2: Manufacturer: GenesysLogic [11:00:19.636][ 1.482748] hub 1-2:1.0: USB hub found [11:00:19.638][ 1.483004] hub 1-2:1.0: 4 ports detected [11:00:19.647][ 1.493121] Root device found: mmcblk0p1 [11:00:19.649][ 1.494273] Found dev node: /dev/mmcblk0p1 [11:00:19.657][ 1.717930] EXT4-fs (mmcblk0p1): 2 orphan inodes deleted [11:00:19.659][ 1.717933] EXT4-fs (mmcblk0p1): recovery complete [11:00:19.669][ 1.733529] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [11:00:19.671][ 1.734298] Rootfs mounted over mmcblk0p1 [11:00:19.681][ 1.749167] Switching from initrd to actual rootfs [11:00:19.683][ 1.794958] usb 1-2.4: new full-speed USB device number 3 using tegra-xusb [11:00:19.690][ 1.816448] usb 1-2.4: New USB device found, idVendor=1a86, idProduct=e5e3 [11:00:19.702][ 1.816453] usb 1-2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [11:00:19.702][ 1.816457] usb 1-2.4: Product: USB2IIC_CTP_CONTROL [11:00:19.704][ 1.816460] usb 1-2.4: Manufacturer: wch.cn [11:00:19.712][ 1.821605] input: wch.cn USB2IIC_CTP_CONTROL as /devices/70090000.xusb/usb1/1-2/1-2.4/1-2.4:1.0/0003:1A86:E5E3.0001/input/input2 [11:00:19.735][ 1.821910] hid-multitouch 0003:1A86:E5E3.0001: input,hidraw0: USB HID v1.00 Device [wch.cn USB2IIC_CTP_CONTROL] on usb-70090000.xusb-2.4/input0 [11:00:19.736][ 1.852933] ip_tables: (C) 2000-2006 Netfilter Core Team [11:00:19.737][ 1.864122] cgroup: cgroup2: unknown option "nsdelegate" [11:00:19.755][ 1.873040] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [11:00:19.769][ 1.873790] systemd[1]: Detected architecture arm64. [11:00:19.771][ 1.896019] systemd[1]: No hostname configured. [11:00:19.779][ 1.896034] systemd[1]: Set hostname to . [11:00:19.791][ 1.979506] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [11:00:19.800][ 1.979516] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [11:00:19.812][ 2.038962] tegra_cec 70015000.tegra_cec: physical address: 10:00. [11:00:19.822][ 2.052449] systemd[1]: Configuration file /etc/systemd/system/mybak.service is marked executable. Please remove executable permission bits. Proceeding anyway. [11:00:19.834][ 2.053042] systemd[1]: /etc/systemd/system/mybak.service:7: Unknown lvalue 'type' in section 'Service' [11:00:19.846][ 2.053386] systemd[1]: /etc/systemd/system/myapp.service:7: Unknown lvalue 'type' in section 'Service' [11:00:19.847][ 2.085408] random: systemd: uninitialized urandom read (16 bytes read) [11:00:19.856][ 2.086904] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [11:00:19.867][ 2.087041] random: systemd: uninitialized urandom read (16 bytes read) [11:00:19.879][ 2.087183] random: systemd: uninitialized urandom read (16 bytes read) [11:00:19.882][ 2.142331] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null) [11:00:19.889][ 2.438184] systemd-journald[2007]: Received request to flush runtime journal from PID 1 [11:00:19.901][ 2.694786] nvgpu: 57000000.gpu gm20b_init_clk_setup_sw:1268 [INFO] GPCPLL initial settings: NA mode, M=1, N=34, P=3 (id = 1) [11:00:19.903][ 3.229077] using random self ethernet address [11:00:19.912][ 3.249344] using random host ethernet address [11:00:19.913][ 3.371236] FAT-fs (loop0): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [11:00:19.923][ 3.457705] random: crng init done [11:00:19.924][ 3.461118] random: 7 urandom warning(s) missed due to ratelimiting [11:00:19.934][ 3.479115] dvrs_hw: loading out-of-tree module taints kernel. [11:00:19.935][ 3.490143] uio Device =6141 VID =8888 [11:00:19.945][ 3.490160] dvrs_hw 0000:01:00.0: enabling device (0000 -> 0002) [11:00:19.945][ 3.490180] msi_msix_capable in [11:00:19.946][ 3.490193] pci_enable_msi() [11:00:19.956][ 3.490318] Using IRQ#407 with 0xffffffc0eb345800 [11:00:19.957][ 3.490323] ************[HW]-[VIDV]=[120]-[1] ************ [11:00:19.968][ 3.490603] [MV]kmalloc_area at 0xffffffc0ee800000 (phys 0x000000016e800000) [11:00:19.970][ 3.490606] [MV]Mem Video::m_dwAudioBuffer = 6e800000 [11:00:19.978][ 3.490608] [MV]Mem Video::m_dwAudioBufferHigh = 1 [11:00:19.979][ 3.490639] [MV]1-DispatchCreate[X64] PhyAddr_A_Low 60000000=60000000 PhyAddr_A_High 1=1 [11:00:19.990][ 3.490644] [MV]1-DispatchCreate[X64]AUDIO BUF 1E800000=1E800000 [11:00:19.991][ 3.490650] [MV]1 CTL Reg=8B0(16777216) [11:00:20.002][ 3.884969] using random self ethernet address [11:00:20.004][ 3.889728] using random host ethernet address [11:00:20.011][ 4.061244] rndis0: HOST MAC 5e:9e:09:fd:7a:58 [11:00:20.011][ 4.070441] rndis0: MAC 5e:9e:09:fd:7a:59 [11:00:20.012][ 4.071497] usb0: HOST MAC 5e:9e:09:fd:7a:5a [11:00:20.023][ 4.071566] usb0: MAC 5e:9e:09:fd:7a:5b [11:00:20.024][ 4.071591] tegra-xudc-new 700d0000.xudc: exiting ELPG [11:00:20.034][ 4.073036] tegra-xudc-new 700d0000.xudc: exiting ELPG done [11:00:20.035][ 4.073055] tegra-xudc-new 700d0000.xudc: ep 0 (type: 0, dir: out) enabled [11:00:20.045][ 4.073114] tegra-xudc-new 700d0000.xudc: entering ELPG [11:00:20.046][ 4.073373] tegra-xudc-new 700d0000.xudc: entering ELPG done [11:00:20.056][ 4.073406] tegra-xudc-new 700d0000.xudc: exiting ELPG [11:00:20.057][ 4.073717] zram: Added device: zram0 [11:00:20.069][ 4.074455] tegra-xudc-new 700d0000.xudc: exiting ELPG done [11:00:20.069][ 4.074483] tegra-xudc-new 700d0000.xudc: entering ELPG [11:00:20.070][ 4.074724] tegra-xudc-new 700d0000.xudc: entering ELPG done [11:00:20.078][ 4.088678] zram: Added device: zram1 [11:00:20.079][ 4.090370] l4tbr0: port 1(rndis0) entered blocking state [11:00:20.091][ 4.090375] l4tbr0: port 1(rndis0) entered disabled state [11:00:20.092][ 4.090541] device rndis0 entered promiscuous mode [11:00:20.103][ 4.104638] zram: Added device: zram2 [11:00:20.103][ 4.106067] IPv6: ADDRCONF(NETDEV_UP): rndis0: link is not ready [11:00:20.105][ 4.110466] zram: Added device: zram3 [11:00:20.112][ 4.127363] l4tbr0: port 2(usb0) entered blocking state [11:00:20.114][ 4.127368] l4tbr0: port 2(usb0) entered disabled state [11:00:20.124][ 4.138811] device usb0 entered promiscuous mode [11:00:20.126][ 4.157942] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready [11:00:20.135][ 4.180607] zram0: detected capacity change from 0 to 518557696 [11:00:20.136][ 4.215013] tegra_cec 70015000.tegra_cec: timeout in tegra_cec_native_write_l:172. [11:00:20.145][ 4.223223] tegra_cec 70015000.tegra_cec: Sent res: -62. [11:00:20.156][ 4.230078] tegra_cec 70015000.tegra_cec: tegra_cec_init Done. [11:00:20.158][ 4.270531] Adding 506400k swap on /dev/zram0. Priority:5 extents:1 across:506400k SS [11:00:20.166][ 4.274783] zram1: detected capacity change from 0 to 518557696 [11:00:20.179][ 4.295446] Adding 506400k swap on /dev/zram1. Priority:5 extents:1 across:506400k SS [11:00:20.180][ 4.310730] zram2: detected capacity change from 0 to 518557696 [11:00:20.190][ 4.340808] Adding 506400k swap on /dev/zram2. Priority:5 extents:1 across:506400k SS [11:00:20.191][ 4.360909] zram3: detected capacity change from 0 to 518557696 [11:00:20.200][ 4.378361] Adding 506400k swap on /dev/zram3. Priority:5 extents:1 across:506400k SS [11:00:20.213][ 4.667683] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [11:00:20.214][ 4.668806] eth0: 0xffffff800a4ba000, 00:04:4b:e9:e8:8b, IRQ 405 [11:00:20.223][ 4.777522] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [11:00:20.224][ 5.297782] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0 [11:00:20.235][ 5.297789] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0 [11:00:20.236][ 5.543481] SetAudioSampleRate = [82] [11:00:20.245][ 5.623361] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [11:00:20.247][ 5.646174] usb 2-1: New USB device found, idVendor=05e3, idProduct=0620 [11:00:20.256][ 5.646181] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [11:00:20.257][ 5.646186] usb 2-1: Product: USB3.2 Hub [11:00:20.268][ 5.646189] usb 2-1: Manufacturer: GenesysLogic [11:00:20.269][ 5.647199] hub 2-1:1.0: USB hub found [11:00:20.270][ 5.647533] hub 2-1:1.0: 4 ports detected [11:00:20.277][ 5.935411] usb 2-1.3: new SuperSpeed USB device number 3 using tegra-xusb [11:00:20.290][ 5.957965] usb 2-1.3: New USB device found, idVendor=05e3, idProduct=0749 [11:00:20.291][ 5.957973] usb 2-1.3: New USB device strings: Mfr=3, Product=4, SerialNumber=2 [11:00:20.301][ 5.957976] usb 2-1.3: Product: USB3.0 Card Reader [11:00:20.301][ 5.957980] usb 2-1.3: Manufacturer: Generic [11:00:20.303][ 5.957983] usb 2-1.3: SerialNumber: 000000001532 [11:00:20.313][ 5.959021] usb-storage 2-1.3:1.0: USB Mass Storage device detected [11:00:20.315][ 5.963280] scsi host0: usb-storage 2-1.3:1.0 [11:00:20.324][ 6.968184] scsi 0:0:0:0: Direct-Access Generic STORAGE DEVICE 1532 PQ: 0 ANSI: 6 [11:00:20.327][ 7.258347] SetAudioSampleRate = [82] [11:00:20.337][ 7.259091] dvrs_hw StartSys [11:00:20.339][ 7.267505] irq 407 handler irqhandler+0x0/0xf0 [dvrs_hw] enabled interrupts [11:00:20.345][ 7.267514] ------------[ cut here ]------------ [11:00:20.356][ 7.272138] WARNING: CPU: 0 PID: 0 at kernel/irq/handle.c:149 __handle_irq_event_percpu+0x238/0x288 [11:00:20.356][ 7.281168] Modules linked in: spidev zram overlay dvrs_hw(O) nvgpu bluedroid_pm ip_tables x_tables [11:00:20.358] [11:00:20.366][ 7.281190] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G O 4.9.140-tegra #10 [11:00:20.378][ 7.281192] Hardware name: NVIDIA Jetson Nano Developer Kit (DT) [11:00:20.380][ 7.281195] task: ffffff8009ef13c0 task.stack: ffffff8009ee0000 [11:00:20.390][ 7.281198] PC is at __handle_irq_event_percpu+0x238/0x288 [11:00:20.392][ 7.281201] LR is at __handle_irq_event_percpu+0x238/0x288 [11:00:20.401][ 7.281204] pc : [] lr : [] pstate: 80400045 [11:00:20.402][ 7.281206] sp : ffffffc0fefb4d50 [11:00:20.413][ 7.281208] x29: ffffffc0fefb4d50 x28: ffffff8009ef13c0 [11:00:20.414][ 7.281213] x27: ffffff800a11a000 x26: ffffffc0ed23be00 [11:00:20.423][ 7.281218] x25: ffffffc0fefb4ddc x24: ffffff80098aa018 [11:00:20.424][ 7.281223] x23: ffffff8009ee6e48 x22: 0000000000000197 [11:00:20.433][ 7.281228] x21: 0000000000000000 x20: 0000000000000001 [11:00:20.433][ 7.281233] x19: ffffffc0f3403580 x18: 0000000000000060 [11:00:20.434][ 7.281238] x17: 0000000000000000 x16: 0000000000000000 [11:00:20.447][ 7.281242] x15: ffffffffffffffff x14: 7374707572726574 [11:00:20.448][ 7.281247] x13: 0000000000000000 x12: 0000000000000006 [11:00:20.456][ 7.281252] x11: 0000000000000002 x10: 0000000000000348 [11:00:20.457][ 7.281256] x9 : 0000000000000001 x8 : ffffffc0fefa2fec [11:00:20.468][ 7.281261] x7 : 0000000000000000 x6 : ffffffc0fefb5bf0 [11:00:20.469][ 7.281266] x5 : 0000000000000001 x4 : 0000000000000000 [11:00:20.477][ 7.281270] x3 : ffffff8009eeb2c0 x2 : 0000000000000040 [11:00:20.477][ 7.281275] x1 : ffffff8009ef13c0 x0 : 0000000000000040 [11:00:20.478] [11:00:20.489][ 7.281282] ---[ end trace ee99213fb1d91a50 ]--- [11:00:20.490][ 7.285889] Call trace: [11:00:20.501][ 7.285893] [] __handle_irq_event_percpu+0x238/0x288 [11:00:20.502][ 7.285896] [] handle_irq_event_percpu+0x28/0x60 [11:00:20.511][ 7.285899] [] handle_irq_event+0x50/0x80 [11:00:20.513][ 7.285904] [] handle_simple_irq+0x8c/0xc0 [11:00:20.522][ 7.285907] [] generic_handle_irq+0x34/0x50 [11:00:20.524][ 7.285913] [] tegra_pcie_msi_irq+0x64/0x140 [11:00:20.535][ 7.285916] [] __handle_irq_event_percpu+0x68/0x288 [11:00:20.536][ 7.285919] [] handle_irq_event_percpu+0x28/0x60 [11:00:20.544][ 7.285922] [] handle_irq_event+0x50/0x80 [11:00:20.545][ 7.285925] [] handle_fasteoi_irq+0xc8/0x1b8 [11:00:20.556][ 7.285928] [] generic_handle_irq+0x34/0x50 [11:00:20.558][ 7.285931] [] __handle_domain_irq+0x68/0xc0 [11:00:20.566][ 7.285935] [] gic_handle_irq+0x5c/0xb0 [11:00:20.568][ 7.285939] [] el1_irq+0xe8/0x194 [11:00:20.578][ 7.285944] [] cpuidle_enter_state+0xb8/0x380 [11:00:20.580][ 7.285947] [] cpuidle_enter+0x34/0x48 [11:00:20.591][ 7.285951] [] call_cpuidle+0x44/0x70 [11:00:20.592][ 7.285954] [] cpu_startup_entry+0x1b0/0x200 [11:00:20.599][ 7.285960] [] rest_init+0x84/0x90 [11:00:20.601][ 7.285965] [] start_kernel+0x370/0x384 [11:00:20.611][ 7.285968] [] __primary_switched+0x80/0x94 [11:00:20.613][ 7.310215] sd 0:0:0:0: [sda] 124735488 512-byte logical blocks: (63.9 GB/59.5 GiB) [11:00:20.622][ 7.318653] sd 0:0:0:0: [sda] Write Protect is off [11:00:20.624][ 7.323517] sd 0:0:0:0: [sda] Mode Sense: 21 00 00 00 [11:00:20.634][ 7.324066] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [11:00:20.635][ 7.337940] sda: sda1 [11:00:20.644][ 7.343000] sd 0:0:0:0: [sda] Attached SCSI removable disk [11:00:20.644][ 7.700707] fuse init (API version 7.26) [11:00:20.645][ 7.831737] r8168: eth0: link up [11:00:20.656][ 7.831760] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [11:00:20.657][ 13.367304] [MV]No Audio Buffer to wirte [11:00:20.675][ 13.375643] [MV]No Audio Buffer to wirte [11:00:20.675][ 13.383973] [MV]No Audio Buffer to wirte [11:00:20.676][ 13.442307] [MV]No Audio Buffer to wirte [11:00:29.290] [11:00:29.535] [11:00:29.717] [11:00:29.869] [11:00:30.050] [11:00:30.206] [11:00:31.777]^C