Script started on Wed Mar 24 19:23:46 2021 command: screen /dev/cu.usbserial-0133C2DA 115200 [?1049h[!p[?3;4l>[?1h=(B[ 111.700626] watchdog: watchdog0: watchdog did not stop! [ 111.711281] systemd-shutdow: 34 output lines suppressed due to ratelimiting [ 112.152666] reboot: Restarting system [0000.159] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de) [0000.164] Processing in cold boot mode Bootloader 2 [0000.169] A02 Bootrom Patch rev = 1023 [0000.173] Power-up reason: software reset [0000.176] No Battery Present [0000.179] pmic max77620 reset reason [0000.182] pmic max77620 NVERC : 0x0 [0000.186] RamCode = 0 [0000.188] Platform has DDR4 type RAM [0000.191] max77620 disabling SD1 Remote Sense [0000.195] Setting DDR voltage to 1125mv [0000.199] Serial Number of Pmic Max77663: 0xc22cf [0000.207] Entering ramdump check [0000.210] Get RamDumpCarveOut = 0x0 [0000.213] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.218] Last reboot was clean, booting normally! [0000.223] Sdram initialization is successful [0000.227] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.233] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.239] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.245] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.251] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.257] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.262] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.268] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.284] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.290] Platform-DebugCarveout: 0 [0000.294] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.299] Non secure mode, and RB not enabled. [0000.304] BoardID = 3448, SKU = 0x0 [0000.307] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.311] Nano-SD: checking PT table on QSPI ... [0000.315] Read PT from (2:0) [0000.331] Using BFS PT to query partitions [0000.336] Loading Tboot-CPU binary [0000.365] Verifying TBC in OdmNonSecureSBK mode [0000.375] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.382] Bootloader downloaded successfully. [0000.386] Downloaded Tboot-CPU binary to 0xa0000258 [0000.391] MAX77620_GPIO5 configured [0000.394] CPU power rail is up [0000.397] CPU clock enabled [0000.401] Performing RAM repair [0000.404] Updating A64 Warmreset Address to 0xa00002e9 [0000.409] BoardID = 3448, SKU = 0x0 [0000.412] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.416] Nano-SD: checking PT table on QSPI ... [0000.420] Loading NvTbootBootloaderDTB [0000.487] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.560] Bootloader DTB Load Address: 0x83000000 [0000.564] BoardID = 3448, SKU = 0x0 [0000.568] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.571] Nano-SD: checking PT table on QSPI ... [0000.576] Loading NvTbootKernelDTB [0000.642] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.715] Kernel DTB Load Address: 0x83100000 [0000.719] BoardID = 3448, SKU = 0x0 [0000.723] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.726] Nano-SD: checking PT table on QSPI ... [0000.732] Loading cboot binary [0000.848] Verifying EBT in OdmNonSecureSBK mode [0000.890] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.897] Bootloader downloaded successfully. [0000.901] BoardID = 3448, SKU = 0x0 [0000.904] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.908] Nano-SD: checking PT table on QSPI ... [0000.913] PT: Partition NCT NOT found ! [0000.917] Warning: Find Partition via PT Failed [0000.921] Next binary entry address: 0x92c00258 [0000.925] BoardId: 3448 [0000.930] Overriding pmu board id with proc board id [0000.935] Display board id is not available [0000.939] BoardID = 3448, SKU = 0x0 [0000.942] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.946] Nano-SD: checking PT table on QSPI ... [0001.051] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.108] /bpmp deleted [0001.110] SC7EntryFw header found loaded at 0xff700000 [0001.305] OVR2 PMIC [0001.307] Bpmp FW successfully loaded [0001.311] BoardID = 3448, SKU = 0x0 [0001.314] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.318] Nano-SD: checking PT table on QSPI ... [0001.323] WB0 init successfully at 0xff780000 [0001.327] Set NvDecSticky Bits [0001.331] GSC2 address ff53fffc value c0edbbcc [0001.337] GSC MC Settings done [0001.340] BoardID = 3448, SKU = 0x0 [0001.343] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.347] Nano-SD: checking PT table on QSPI ... [0001.353] TOS Image length 53680 [0001.356] Monitor size 53680 [0001.358] OS size 0 [0001.374] Secure Os AES-CMAC Verification Success! [0001.378] TOS image cipher info: plaintext [0001.382] Loading and Validation of Secure OS Successful [0001.398] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.403] NvTbootPackSdramParams: start. [0001.408] NvTbootPackSdramParams: done. [0001.412] Tegraboot started after 86957 us [0001.415] Basic modules init took 886913 us [0001.419] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB [0001.425] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.430] Next stage binary read took 102860 us [0001.435] Carveout took -126357 us [0001.438] CPU initialization took 495396 us [0001.442] Total time taken by TegraBoot 1358812 us [0001.447] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):5b49e7f80 NOTICE: BL31: Built : 14:33:23, Jan 15 2021 ERROR: Error initializing runtime service trusty_fast [0001.569] RamCode = 0 [0001.574] LPDDR4 Training: Read DT: Number of tables = 2 [0001.579] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.591] EMC Training Successful [0001.595] 408000 not found in DVFS table [0001.601] RamCode = 0 [0001.604] DT Write: emc-table@204000 succeeded [0001.610] DT Write: emc-table@1600000 succeeded [0001.614] LPDDR4 Training: Write DT: Number of tables = 2 [0001.662] [0001.663] Debug Init done [0001.665] Marked DTB cacheable [0001.668] Bootloader DTB loaded at 0x83000000 [0001.673] Marked DTB cacheable [0001.676] Kernel DTB loaded at 0x83100000 [0001.680] DeviceTree Init done [0001.693] Pinmux applied successfully [0001.697] gicd_base: 0x50041000 [0001.701] gicc_base: 0x50042000 [0001.704] Interrupts Init done [0001.708] Using base:0x60005090 & irq:208 for tick-timer [0001.713] Using base:0x60005098 for delay-timer [0001.718] platform_init_timer: DONE [0001.721] Timer(tick) Init done [0001.725] osc freq = 38400 khz [0001.729] [0001.730] Welcome to L4T Cboot [0001.733] [0001.734] Cboot Version: 00.00.2018.01-t210-39562017 [0001.739] calling constructors [0001.742] initializing heap [0001.744] initializing threads [0001.747] initializing timers [0001.750] creating bootstrap completion thread [0001.755] top of bootstrap2() [0001.758] CPU: ARM Cortex A57 [0001.760] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.765] initializing platform [0001.773] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.777] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.782] Macronix QSPI chip present [0001.785] SPI device register [0001.788] init boot device [0001.791] allocating memory for boot device(SPI) [0001.795] registering boot device [0001.809] QSPI bdev is already initialized [0001.813] Enable APE clock [0001.815] Un-powergate APE partition [0001.819] of_register: registering tegra_udc to of_hal [0001.824] of_register: registering inv20628-driver to of_hal [0001.829] of_register: registering ads1015-driver to of_hal [0001.835] of_register: registering lp8557-bl-driver to of_hal [0001.841] of_register: registering bq2419x_charger to of_hal [0001.846] of_register: registering bq27441_fuel_gauge to of_hal [0001.858] gpio framework initialized [0001.861] of_register: registering tca9539_gpio to of_hal [0001.867] of_register: registering tca9539_gpio to of_hal [0001.872] of_register: registering i2c_bus_driver to of_hal [0001.878] of_register: registering i2c_bus_driver to of_hal [0001.883] of_register: registering i2c_bus_driver to of_hal [0001.889] pmic framework initialized [0001.892] of_register: registering max77620_pmic to of_hal [0001.898] regulator framework initialized [0001.902] of_register: registering tps65132_bl_driver to of_hal [0001.908] initializing target [0001.913] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.922] board ID = D78, board SKU = 0 [0001.925] Skipping Z3! [0001.930] fixed regulator driver initialized [0001.948] initializing OF layer [0001.951] NCK carveout not present [0001.954] Skipping dts_overrides [0001.958] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.975] I2C Bus Init done [0001.978] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.988] I2C Bus Init done [0001.991] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.001] I2C Bus Init done [0002.004] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.014] I2C Bus Init done [0002.017] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.027] I2C Bus Init done [0002.030] of_children_init: Ops found for compatible string maxim,max77620 [0002.040] max77620_init using irq 118 [0002.045] register 'maxim,max77620' pmic [0002.050] gpio_driver_register: register 'max77620-gpio' driver [0002.056] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.066] I2C Bus Init done [0002.070] NCK carveout not present [0002.080] Find /i2c@7000c000's alias i2c0 [0002.084] get eeprom at 1-a0, size 256, type 0 [0002.093] Find /i2c@7000c500's alias i2c2 [0002.096] get eeprom at 3-a0, size 256, type 0 [0002.101] get eeprom at 3-ae, size 256, type 0 [0002.105] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.111] I2C slave not started [0002.114] I2C write failed [0002.116] Writing offset failed [0002.119] eeprom_init: EEPROM read failed [0002.123] pm_ids_update: eeprom init failed [0002.127] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.157] pm_ids_update: The pm board id is 3448-0000-400 [0002.164] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.173] pm_ids_update: pm id update successful [0002.177] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.207] pm_ids_update: The pm board id is 3449-0000-400 [0002.213] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.221] pm_ids_update: pm id update successful [0002.252] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.258] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.265] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.271] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.280] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ec:39:dc [0002.286] Plugin Manager: Parse ODM data 0x000a4000 [0002.298] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.313] Find /i2c@7000c000's alias i2c0 [0002.317] get eeprom at 1-a0, size 256, type 0 [0002.326] Find /i2c@7000c500's alias i2c2 [0002.330] get eeprom at 3-a0, size 256, type 0 [0002.334] get eeprom at 3-ae, size 256, type 0 [0002.339] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.344] I2C slave not started [0002.347] I2C write failed [0002.350] Writing offset failed [0002.353] eeprom_init: EEPROM read failed [0002.357] pm_ids_update: eeprom init failed [0002.361] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.391] pm_ids_update: The pm board id is 3448-0000-400 [0002.397] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.404] pm_ids_update: pm id update successful [0002.409] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.439] pm_ids_update: The pm board id is 3449-0000-400 [0002.445] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.452] pm_ids_update: pm id update successful [0002.482] Add serial number:1423519045845 as DT property [0002.490] Applying platform configs [0002.497] platform-init is not present. Skipping [0002.501] calling apps_init() [0002.507] Couldn't find GPT header [0002.512] Proceeding to Cold Boot [0002.515] starting app android_boot_app [0002.518] Device state: unlocked [0002.522] display console init [0002.530] could not find regulator [0002.533] hdmi cable connected [0002.549] edid read success [0002.564] DT entry for leds-pwm not found [0002.568] edid read success [0002.571] width = 640, height = 480, frequency = 25174825 [0002.576] width = 640, height = 480, frequency = 25174825 [0002.581] width = 640, height = 480, frequency = 25174825 [0002.587] width = 1920, height = 1080, frequency = 148500000 [0002.592] width = 1920, height = 540, frequency = 74250000 [0002.598] width = 640, height = 480, frequency = 25174825 [0002.603] width = 720, height = 480, frequency = 26973026 [0002.609] width = 720, height = 480, frequency = 26973026 [0002.614] width = 1280, height = 720, frequency = 74175824 [0002.619] width = 1920, height = 1080, frequency = 148351648 [0002.625] width = 720, height = 576, frequency = 26973026 [0002.630] width = 720, height = 576, frequency = 26973026 [0002.636] width = 1280, height = 720, frequency = 74175824 [0002.641] width = 1920, height = 1080, frequency = 148351648 [0002.647] Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.655] tmds-config node not found [0002.659] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0002.673] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.681] could not find regulator [0002.684] could not find regulator [0002.688] could not find regulator [0002.716] using default cmu settings [0002.720] dc_hdmi_enable, starting HDMI initialisation [0002.726] dc_hdmi_enable, HDMI initialisation complete [0002.731] list and configure display window [0002.740] display console init completed [0002.751] subnode volume_up is not found ! [0002.755] subnode back is not found ! [0002.758] subnode volume_down is not found ! [0002.763] subnode menu is not found ! [0002.766] Gpio keyboard init success [0002.847] found decompressor handler: lz4-legacy [0002.861] decompressing blob (type 1)... [0002.931] load_bmp_blob: panelresolution=1080 type=3 [0003.006] decompressor handler not found [0003.009] load_firmware_blob: Firmware blob loaded, entries=2 [0003.015] XUSB blob version 0 size 124416 @ 0x934ae28c [0003.021] -------> se_aes_verify_sbk_clear: 747 [0003.026] se_aes_verify_sbk_clear: Error [0003.029] SE operation failed [0003.032] bl_battery_charging: connected to external power supply [0003.045] device_query_partition_size: failed to open partition spiflash0:MSC ! [0003.052] MSC Partition not found [0003.058] device_query_partition_size: failed to open partition spiflash0:USP ! [0003.065] USP partition read failed! [0003.069] blob_init: blob-partition USP header read failed [0003.074] android_boot Unable to update recovery partition [0003.080] kfs_getpartname: name = LNX [0003.083] Loading kernel from LNX [0003.093] Found 19 BFS partitions in "spiflash0" [0003.416] load kernel from storage [0003.421] decompressor handler not found [0003.689] Successfully loaded kernel and ramdisk images [0003.694] board ID = D78, board SKU = 0 [0003.698] sdmmc node status = okay [0003.702] sdcard instance = 0 [0003.705] sdcard gpio handle 0x5b [0003.708] sdcard gpio pin 0xc9 [0003.711] sdcard gpio flags 0x0 [0003.714] vmmc-supply 0x9e [0003.716] cd_gpio_pin = 201 [0003.719] pin_state = 0 [0003.721] Found sdcard [0003.724] SD-card IS present ... [0003.727] load_and_boot_kernel: SD card detected OK [0003.733] load_bmp_blob: panelresolution=1080 type=3 [0004.227] display bmp image done [0004.230] NCK carveout not present [0004.233] Skipping dts_overrides [0004.236] NCK carveout not present [0004.246] Find /i2c@7000c000's alias i2c0 [0004.250] get eeprom at 1-a0, size 256, type 0 [0004.259] Find /i2c@7000c500's alias i2c2 [0004.263] get eeprom at 3-a0, size 256, type 0 [0004.267] get eeprom at 3-ae, size 256, type 0 [0004.272] pm_ids_update: Updating 1,a0, size 256, type 0 [0004.277] I2C slave not started [0004.280] I2C write failed [0004.283] Writing offset failed [0004.286] eeprom_init: EEPROM read failed [0004.290] pm_ids_update: eeprom init failed [0004.294] pm_ids_update: Updating 3,a0, size 256, type 0 [0004.324] pm_ids_update: The pm board id is 3448-0000-400 [0004.331] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0004.339] pm_ids_update: pm id update successful [0004.344] pm_ids_update: Updating 3,ae, size 256, type 0 [0004.374] pm_ids_update: The pm board id is 3449-0000-400 [0004.380] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0004.388] pm_ids_update: pm id update successful [0004.418] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.424] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0004.432] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.438] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0004.446] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ec:39:dc [0004.453] Plugin Manager: Parse ODM data 0x000a4000 [0004.465] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0004.473] Add serial number:1423519045845 as DT property [0004.482] "bpmp" doesn't exist, creating [0004.488] Updated bpmp info to DTB [0004.493] Updated initrd info to DTB [0004.496] "proc-board" doesn't exist, creating [0004.502] Updated board info to DTB [0004.506] "pmu-board" doesn't exist, creating [0004.512] Updated board info to DTB [0004.515] "display-board" doesn't exist, creating [0004.521] Updated board info to DTB [0004.524] "reset" doesn't exist, creating [0004.529] Updated reset info to DTB [0004.532] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 [0004.572] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0004.577] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0004.590] Updated bootarg info to DTB [0004.594] Adding uuid 000000016445c84604000000050403c0 to DT [0004.600] Adding eks info 0 to DT [0004.605] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0004.611] Updated memory info to DTB [0004.619] set vdd_core voltage to 1075 mv [0004.623] setting 'vdd-core' regulator to 1075000 micro volts [0004.629] Found secure-pmc; disable BPMP U-Boot 2020.04-g6b630d64fd (Jan 15 2021 - 14:33:20 -0800) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 1096 bytes read in 26 ms (41 KiB/s) L4T boot options 1:primary kernel 2:overlayfs Enter choice: 2 2:overlayfs Retrieving file: /boot/initrd-4.9.201-fixed-tegra.img 31197232 bytes read in 1372 ms (21.7 MiB/s) Retrieving file: /boot/Image 34338824 bytes read in 1502 ms (21.8 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000083100000, end 000000008317e68d copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.201-tegra (buildbrain@mobile-u64-4415) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Fri Jan 15 14:41:02 PST 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00800000@92ca9000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57560 r8192 d32552 u98304 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29260(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3552524K/4159488K available (15294K kernel code, 2942K rwdata, 6664K rodata, 8576K init, 609K bss, 131828K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f70000 ( 15296 KB) [ 0.000000] .rodata : 0xffffff8008f70000 - 0xffffff8009600000 ( 6720 KB) [ 0.000000] .init : 0xffffff8009600000 - 0xffffff8009e60000 ( 8576 KB) [ 0.000000] .data : 0xffffff8009e60000 - 0xffffff800a13f808 ( 2943 KB) [ 0.000000] .bss : 0xffffff800a13f808 - 0xffffff800a1d7cbc ( 610 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.010099] Console: colour dummy device 80x25 [ 0.014761] console [tty0] enabled [ 0.018280] bootconsole [uart8250] disabled [0000.159] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de) [0000.164] Processing in cold boot mode Bootloader 2 [0000.169] A02 Bootrom Patch rev = 1023 [0000.173] Power-up reason: software reset [0000.176] No Battery Present [0000.179] pmic max77620 reset reason [0000.182] pmic max77620 NVERC : 0x0 [0000.186] RamCode = 0 [0000.188] Platform has DDR4 type RAM [0000.191] max77620 disabling SD1 Remote Sense [0000.195] Setting DDR voltage to 1125mv [0000.199] Serial Number of Pmic Max77663: 0xc22cf [0000.207] Entering ramdump check [0000.210] Get RamDumpCarveOut = 0x0 [0000.213] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.218] Last reboot was clean, booting normally! [0000.223] Sdram initialization is successful [0000.227] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.233] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.239] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.245] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.251] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.257] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.262] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.268] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.284] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.290] Platform-DebugCarveout: 0 [0000.294] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.299] Non secure mode, and RB not enabled. [0000.304] BoardID = 3448, SKU = 0x0 [0000.307] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.311] Nano-SD: checking PT table on QSPI ... [0000.315] Read PT from (2:0) [0000.331] Using BFS PT to query partitions [0000.336] Loading Tboot-CPU binary [0000.365] Verifying TBC in OdmNonSecureSBK mode [0000.375] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.382] Bootloader downloaded successfully. [0000.386] Downloaded Tboot-CPU binary to 0xa0000258 [0000.391] MAX77620_GPIO5 configured [0000.394] CPU power rail is up [0000.397] CPU clock enabled [0000.401] Performing RAM repair [0000.404] Updating A64 Warmreset Address to 0xa00002e9 [0000.409] BoardID = 3448, SKU = 0x0 [0000.412] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.416] Nano-SD: checking PT table on QSPI ... [0000.420] Loading NvTbootBootloaderDTB [0000.487] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.560] Bootloader DTB Load Address: 0x83000000 [0000.564] BoardID = 3448, SKU = 0x0 [0000.568] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.571] Nano-SD: checking PT table on QSPI ... [0000.576] Loading NvTbootKernelDTB [0000.642] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.715] Kernel DTB Load Address: 0x83100000 [0000.719] BoardID = 3448, SKU = 0x0 [0000.723] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.726] Nano-SD: checking PT table on QSPI ... [0000.732] Loading cboot binary [0000.848] Verifying EBT in OdmNonSecureSBK mode [0000.890] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.897] Bootloader downloaded successfully. [0000.901] BoardID = 3448, SKU = 0x0 [0000.904] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.908] Nano-SD: checking PT table on QSPI ... [0000.913] PT: Partition NCT NOT found ! [0000.917] Warning: Find Partition via PT Failed [0000.921] Next binary entry address: 0x92c00258 [0000.925] BoardId: 3448 [0000.930] Overriding pmu board id with proc board id [0000.935] Display board id is not available [0000.939] BoardID = 3448, SKU = 0x0 [0000.942] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.946] Nano-SD: checking PT table on QSPI ... [0001.051] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.108] /bpmp deleted [0001.110] SC7EntryFw header found loaded at 0xff700000 [0001.305] OVR2 PMIC [0001.307] Bpmp FW successfully loaded [0001.311] BoardID = 3448, SKU = 0x0 [0001.314] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.318] Nano-SD: checking PT table on QSPI ... [0001.323] WB0 init successfully at 0xff780000 [0001.327] Set NvDecSticky Bits [0001.331] GSC2 address ff53fffc value c0edbbcc [0001.337] GSC MC Settings done [0001.340] BoardID = 3448, SKU = 0x0 [0001.343] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.347] Nano-SD: checking PT table on QSPI ... [0001.353] TOS Image length 53680 [0001.356] Monitor size 53680 [0001.358] OS size 0 [0001.374] Secure Os AES-CMAC Verification Success! [0001.378] TOS image cipher info: plaintext [0001.382] Loading and Validation of Secure OS Successful [0001.398] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.403] NvTbootPackSdramParams: start. [0001.408] NvTbootPackSdramParams: done. [0001.412] Tegraboot started after 86957 us [0001.415] Basic modules init took 886913 us [0001.419] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB [0001.425] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.430] Next stage binary read took 102859 us [0001.435] Carveout took -126356 us [0001.438] CPU initialization took 495396 us [0001.442] Total time taken by TegraBoot 1358812 us [0001.447] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):5b49e7f80 NOTICE: BL31: Built : 14:33:23, Jan 15 2021 ERROR: Error initializing runtime service trusty_fast [0001.569] RamCode = 0 [0001.574] LPDDR4 Training: Read DT: Number of tables = 2 [0001.579] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.591] EMC Training Successful [0001.595] 408000 not found in DVFS table [0001.601] RamCode = 0 [0001.605] DT Write: emc-table@204000 succeeded [0001.610] DT Write: emc-table@1600000 succeeded [0001.614] LPDDR4 Training: Write DT: Number of tables = 2 [0001.662] [0001.663] Debug Init done [0001.665] Marked DTB cacheable [0001.668] Bootloader DTB loaded at 0x83000000 [0001.673] Marked DTB cacheable [0001.676] Kernel DTB loaded at 0x83100000 [0001.680] DeviceTree Init done [0001.693] Pinmux applied successfully [0001.697] gicd_base: 0x50041000 [0001.701] gicc_base: 0x50042000 [0001.704] Interrupts Init done [0001.708] Using base:0x60005090 & irq:208 for tick-timer [0001.713] Using base:0x60005098 for delay-timer [0001.718] platform_init_timer: DONE [0001.721] Timer(tick) Init done [0001.725] osc freq = 38400 khz [0001.729] [0001.730] Welcome to L4T Cboot [0001.733] [0001.734] Cboot Version: 00.00.2018.01-t210-39562017 [0001.739] calling constructors [0001.742] initializing heap [0001.744] initializing threads [0001.747] initializing timers [0001.750] creating bootstrap completion thread [0001.755] top of bootstrap2() [0001.758] CPU: ARM Cortex A57 [0001.760] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.765] initializing platform [0001.773] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.777] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.782] Macronix QSPI chip present [0001.785] SPI device register [0001.788] init boot device [0001.791] allocating memory for boot device(SPI) [0001.795] registering boot device [0001.804] QSPI bdev is already initialized [0001.808] Enable APE clock [0001.810] Un-powergate APE partition [0001.814] of_register: registering tegra_udc to of_hal [0001.819] of_register: registering inv20628-driver to of_hal [0001.824] of_register: registering ads1015-driver to of_hal [0001.830] of_register: registering lp8557-bl-driver to of_hal [0001.836] of_register: registering bq2419x_charger to of_hal [0001.841] of_register: registering bq27441_fuel_gauge to of_hal [0001.853] gpio framework initialized [0001.856] of_register: registering tca9539_gpio to of_hal [0001.862] of_register: registering tca9539_gpio to of_hal [0001.867] of_register: registering i2c_bus_driver to of_hal [0001.873] of_register: registering i2c_bus_driver to of_hal [0001.878] of_register: registering i2c_bus_driver to of_hal [0001.884] pmic framework initialized [0001.887] of_register: registering max77620_pmic to of_hal [0001.893] regulator framework initialized [0001.897] of_register: registering tps65132_bl_driver to of_hal [0001.903] initializing target [0001.908] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.917] board ID = D78, board SKU = 0 [0001.920] Skipping Z3! [0001.925] fixed regulator driver initialized [0001.943] initializing OF layer [0001.946] NCK carveout not present [0001.949] Skipping dts_overrides [0001.953] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.970] I2C Bus Init done [0001.973] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.983] I2C Bus Init done [0001.986] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.996] I2C Bus Init done [0001.999] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.009] I2C Bus Init done [0002.012] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.022] I2C Bus Init done [0002.025] of_children_init: Ops found for compatible string maxim,max77620 [0002.035] max77620_init using irq 118 [0002.040] register 'maxim,max77620' pmic [0002.045] gpio_driver_register: register 'max77620-gpio' driver [0002.051] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.061] I2C Bus Init done [0002.065] NCK carveout not present [0002.075] Find /i2c@7000c000's alias i2c0 [0002.079] get eeprom at 1-a0, size 256, type 0 [0002.088] Find /i2c@7000c500's alias i2c2 [0002.091] get eeprom at 3-a0, size 256, type 0 [0002.096] get eeprom at 3-ae, size 256, type 0 [0002.100] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.106] I2C slave not started [0002.109] I2C write failed [0002.111] Writing offset failed [0002.114] eeprom_init: EEPROM read failed [0002.118] pm_ids_update: eeprom init failed [0002.122] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.152] pm_ids_update: The pm board id is 3448-0000-400 [0002.159] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.168] pm_ids_update: pm id update successful [0002.172] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.202] pm_ids_update: The pm board id is 3449-0000-400 [0002.208] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.216] pm_ids_update: pm id update successful [0002.247] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.252] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.260] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.266] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.275] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ec:39:dc [0002.281] Plugin Manager: Parse ODM data 0x000a4000 [0002.293] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.308] Find /i2c@7000c000's alias i2c0 [0002.312] get eeprom at 1-a0, size 256, type 0 [0002.321] Find /i2c@7000c500's alias i2c2 [0002.325] get eeprom at 3-a0, size 256, type 0 [0002.329] get eeprom at 3-ae, size 256, type 0 [0002.334] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.339] I2C slave not started [0002.342] I2C write failed [0002.345] Writing offset failed [0002.348] eeprom_init: EEPROM read failed [0002.352] pm_ids_update: eeprom init failed [0002.356] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.386] pm_ids_update: The pm board id is 3448-0000-400 [0002.392] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.399] pm_ids_update: pm id update successful [0002.403] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.434] pm_ids_update: The pm board id is 3449-0000-400 [0002.440] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.447] pm_ids_update: pm id update successful [0002.477] Add serial number:1423519045845 as DT property [0002.485] Applying platform configs [0002.492] platform-init is not present. Skipping [0002.496] calling apps_init() [0002.502] Couldn't find GPT header [0002.507] Proceeding to Cold Boot [0002.510] starting app android_boot_app [0002.513] Device state: unlocked [0002.517] display console init [0002.525] could not find regulator [0002.528] hdmi cable connected [0002.544] edid read success [0002.559] edid rDT entry for leds-pwm not found e[0002.567] ad success [0002.569] width = 640, height = 480, frequency = 25174825 [0002.574] width = 640, height = 480, frequency = 25174825 [0002.579] width = 640, height = 480, frequency = 25174825 [0002.585] width = 1920, height = 1080, frequency = 148500000 [0002.590] width = 1920, height = 540, frequency = 74250000 [0002.596] width = 640, height = 480, frequency = 25174825 [0002.601] width = 720, height = 480, frequency = 26973026 [0002.607] width = 720, height = 480, frequency = 26973026 [0002.612] width = 1280, height = 720, frequency = 74175824 [0002.618] width = 1920, height = 1080, frequency = 148351648 [0002.623] width = 720, height = 576, frequency = 26973026 [0002.629] width = 720, height = 576, frequency = 26973026 [0002.634] width = 1280, height = 720, frequency = 74175824 [0002.639] width = 1920, height = 1080, frequency = 148351648 [0002.645] Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.653] tmds-config node not found [0002.657] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0002.672] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.679] could not find regulator [0002.683] could not find regulator [0002.686] could not find regulator [0002.714] using default cmu settings [0002.718] dc_hdmi_enable, starting HDMI initialisation [0002.724] dc_hdmi_enable, HDMI initialisation complete [0002.729] list and configure display window [0002.738] display console init completed [0002.749] subnode volume_up is not found ! [0002.753] subnode back is not found ! [0002.757] subnode volume_down is not found ! [0002.761] subnode menu is not found ! [0002.764] Gpio keyboard init success [0002.845] found decompressor handler: lz4-legacy [0002.859] decompressing blob (type 1)... [0002.929] load_bmp_blob: panelresolution=1080 type=3 [0003.004] decompressor handler not found [0003.008] load_firmware_blob: Firmware blob loaded, entries=2 [0003.013] XUSB blob version 0 size 124416 @ 0x934ae28c [0003.019] -------> se_aes_verify_sbk_clear: 747 [0003.024] se_aes_verify_sbk_clear: Error [0003.028] SE operation failed [0003.031] bl_battery_charging: connected to external power supply [0003.043] device_query_partition_size: failed to open partition spiflash0:MSC ! [0003.050] MSC Partition not found [0003.056] device_query_partition_size: failed to open partition spiflash0:USP ! [0003.064] USP partition read failed! [0003.067] blob_init: blob-partition USP header read failed [0003.073] android_boot Unable to update recovery partition [0003.078] kfs_getpartname: name = LNX [0003.082] Loading kernel from LNX [0003.091] Found 19 BFS partitions in "spiflash0" [0003.411] load kernel from storage [0003.416] decompressor handler not found [0003.681] Successfully loaded kernel and ramdisk images [0003.686] board ID = D78, board SKU = 0 [0003.691] sdmmc node status = okay [0003.694] sdcard instance = 0 [0003.697] sdcard gpio handle 0x5b [0003.700] sdcard gpio pin 0xc9 [0003.703] sdcard gpio flags 0x0 [0003.706] vmmc-supply 0x9e [0003.709] cd_gpio_pin = 201 [0003.711] pin_state = 0 [0003.714] Found sdcard [0003.716] SD-card IS present ... [0003.719] load_and_boot_kernel: SD card detected OK [0003.725] load_bmp_blob: panelresolution=1080 type=3 [0004.219] display bmp image done [0004.222] NCK carveout not present [0004.226] Skipping dts_overrides [0004.229] NCK carveout not present [0004.239] Find /i2c@7000c000's alias i2c0 [0004.242] get eeprom at 1-a0, size 256, type 0 [0004.251] Find /i2c@7000c500's alias i2c2 [0004.255] get eeprom at 3-a0, size 256, type 0 [0004.260] get eeprom at 3-ae, size 256, type 0 [0004.264] pm_ids_update: Updating 1,a0, size 256, type 0 [0004.269] I2C slave not started [0004.272] I2C write failed [0004.275] Writing offset failed [0004.278] eeprom_init: EEPROM read failed [0004.282] pm_ids_update: eeprom init failed [0004.286] pm_ids_update: Updating 3,a0, size 256, type 0 [0004.316] pm_ids_update: The pm board id is 3448-0000-400 [0004.323] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0004.331] pm_ids_update: pm id update successful [0004.336] pm_ids_update: Updating 3,ae, size 256, type 0 [0004.366] pm_ids_update: The pm board id is 3449-0000-400 [0004.372] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0004.380] pm_ids_update: pm id update successful [0004.411] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.416] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0004.424] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.430] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0004.438] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ec:39:dc [0004.445] Plugin Manager: Parse ODM data 0x000a4000 [0004.457] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0004.466] Add serial number:1423519045845 as DT property [0004.475] "bpmp" doesn't exist, creating [0004.480] Updated bpmp info to DTB [0004.485] Updated initrd info to DTB [0004.488] "proc-board" doesn't exist, creating [0004.495] Updated board info to DTB [0004.498] "pmu-board" doesn't exist, creating [0004.504] Updated board info to DTB [0004.507] "display-board" doesn't exist, creating [0004.513] Updated board info to DTB [0004.516] "reset" doesn't exist, creating [0004.521] Updated reset info to DTB [0004.525] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 [0004.564] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0004.569] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0004.582] Updated bootarg info to DTB [0004.586] Adding uuid 000000016445c84604000000050403c0 to DT [0004.592] Adding eks info 0 to DT [0004.598] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0004.603] Updated memory info to DTB [0004.611] set vdd_core voltage to 1075 mv [0004.615] setting 'vdd-core' regulator to 1075000 micro volts [0004.621] Found secure-pmc; disable BPMP U-Boot 2020.04-g6b630d64fd (Jan 15 2021 - 14:33:20 -0800) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 1096 bytes read in 26 ms (41 KiB/s) L4T boot options 1:primary kernel 2:overlayfs Enter choice: 2 2:overlayfs Retrieving file: /boot/initrd-4.9.201-fixed-tegra.img 31197232 bytes read in 1372 ms (21.7 MiB/s) Retrieving file: /boot/Image 34338824 bytes read in 1502 ms (21.8 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000083100000, end 000000008317e68d copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.201-tegra (buildbrain@mobile-u64-4415) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Fri Jan 15 14:41:02 PST 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00800000@92ca9000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57560 r8192 d32552 u98304 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29260(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3552524K/4159488K available (15294K kernel code, 2942K rwdata, 6664K rodata, 8576K init, 609K bss, 131828K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f70000 ( 15296 KB) [ 0.000000] .rodata : 0xffffff8008f70000 - 0xffffff8009600000 ( 6720 KB) [ 0.000000] .init : 0xffffff8009600000 - 0xffffff8009e60000 ( 8576 KB) [ 0.000000] .data : 0xffffff8009e60000 - 0xffffff800a13f808 ( 2943 KB) [ 0.000000] .bss : 0xffffff800a13f808 - 0xffffff800a1d7cbc ( 610 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.010061] Console: colour dummy device 80x25 [ 0.014712] console [tty0] enabled [ 0.018219] bootconsole [uart8250] disabled [0000.159] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de) [0000.164] Processing in cold boot mode Bootloader 2 [0000.169] A02 Bootrom Patch rev = 1023 [0000.173] Power-up reason: software reset [0000.176] No Battery Present [0000.179] pmic max77620 reset reason [0000.182] pmic max77620 NVERC : 0x0 [0000.186] RamCode = 0 [0000.188] Platform has DDR4 type RAM [0000.191] max77620 disabling SD1 Remote Sense [0000.195] Setting DDR voltage to 1125mv [0000.199] Serial Number of Pmic Max77663: 0xc22cf [0000.207] Entering ramdump check [0000.210] Get RamDumpCarveOut = 0x0 [0000.213] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.218] Last reboot was clean, booting normally! [0000.223] Sdram initialization is successful [0000.227] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.233] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.239] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.245] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.251] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.257] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.262] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.268] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.284] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.290] Platform-DebugCarveout: 0 [0000.294] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.299] Non secure mode, and RB not enabled. [0000.304] BoardID = 3448, SKU = 0x0 [0000.307] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.311] Nano-SD: checking PT table on QSPI ... [0000.315] Read PT from (2:0) [0000.331] Using BFS PT to query partitions [0000.336] Loading Tboot-CPU binary [0000.365] Verifying TBC in OdmNonSecureSBK mode [0000.375] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.382] Bootloader downloaded successfully. [0000.386] Downloaded Tboot-CPU binary to 0xa0000258 [0000.391] MAX77620_GPIO5 configured [0000.394] CPU power rail is up [0000.397] CPU clock enabled [0000.401] Performing RAM repair [0000.404] Updating A64 Warmreset Address to 0xa00002e9 [0000.409] BoardID = 3448, SKU = 0x0 [0000.412] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.416] Nano-SD: checking PT table on QSPI ... [0000.420] Loading NvTbootBootloaderDTB [0000.487] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.560] Bootloader DTB Load Address: 0x83000000 [0000.564] BoardID = 3448, SKU = 0x0 [0000.568] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.571] Nano-SD: checking PT table on QSPI ... [0000.576] Loading NvTbootKernelDTB [0000.642] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.715] Kernel DTB Load Address: 0x83100000 [0000.719] BoardID = 3448, SKU = 0x0 [0000.723] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.726] Nano-SD: checking PT table on QSPI ... [0000.732] Loading cboot binary [0000.848] Verifying EBT in OdmNonSecureSBK mode [0000.890] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.897] Bootloader downloaded successfully. [0000.901] BoardID = 3448, SKU = 0x0 [0000.904] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.908] Nano-SD: checking PT table on QSPI ... [0000.913] PT: Partition NCT NOT found ! [0000.917] Warning: Find Partition via PT Failed [0000.921] Next binary entry address: 0x92c00258 [0000.925] BoardId: 3448 [0000.930] Overriding pmu board id with proc board id [0000.935] Display board id is not available [0000.939] BoardID = 3448, SKU = 0x0 [0000.942] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.946] Nano-SD: checking PT table on QSPI ... [0001.051] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.108] /bpmp deleted [0001.110] SC7EntryFw header found loaded at 0xff700000 [0001.305] OVR2 PMIC [0001.307] Bpmp FW successfully loaded [0001.311] BoardID = 3448, SKU = 0x0 [0001.314] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.318] Nano-SD: checking PT table on QSPI ... [0001.323] WB0 init successfully at 0xff780000 [0001.327] Set NvDecSticky Bits [0001.331] GSC2 address ff53fffc value c0edbbcc [0001.337] GSC MC Settings done [0001.340] BoardID = 3448, SKU = 0x0 [0001.343] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.347] Nano-SD: checking PT table on QSPI ... [0001.353] TOS Image length 53680 [0001.356] Monitor size 53680 [0001.358] OS size 0 [0001.374] Secure Os AES-CMAC Verification Success! [0001.378] TOS image cipher info: plaintext [0001.382] Loading and Validation of Secure OS Successful [0001.398] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.403] NvTbootPackSdramParams: start. [0001.408] NvTbootPackSdramParams: done. [0001.412] Tegraboot started after 86957 us [0001.415] Basic modules init took 886920 us [0001.419] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB [0001.425] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.430] Next stage binary read took 102860 us [0001.435] Carveout took -126356 us [0001.438] CPU initialization took 495393 us [0001.442] Total time taken by TegraBoot 1358817 us [0001.447] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):5b49e7f80 NOTICE: BL31: Built : 14:33:23, Jan 15 2021 ERROR: Error initializing runtime service trusty_fast [0001.569] RamCode = 0 [0001.574] LPDDR4 Training: Read DT: Number of tables = 2 [0001.579] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.591] EMC Training Successful [0001.595] 408000 not found in DVFS table [0001.601] RamCode = 0 [0001.604] DT Write: emc-table@204000 succeeded [0001.610] DT Write: emc-table@1600000 succeeded [0001.614] LPDDR4 Training: Write DT: Number of tables = 2 [0001.662] [0001.663] Debug Init done [0001.665] Marked DTB cacheable [0001.668] Bootloader DTB loaded at 0x83000000 [0001.673] Marked DTB cacheable [0001.676] Kernel DTB loaded at 0x83100000 [0001.680] DeviceTree Init done [0001.693] Pinmux applied successfully [0001.697] gicd_base: 0x50041000 [0001.701] gicc_base: 0x50042000 [0001.704] Interrupts Init done [0001.708] Using base:0x60005090 & irq:208 for tick-timer [0001.713] Using base:0x60005098 for delay-timer [0001.718] platform_init_timer: DONE [0001.721] Timer(tick) Init done [0001.725] osc freq = 38400 khz [0001.729] [0001.730] Welcome to L4T Cboot [0001.733] [0001.734] Cboot Version: 00.00.2018.01-t210-39562017 [0001.739] calling constructors [0001.742] initializing heap [0001.744] initializing threads [0001.747] initializing timers [0001.750] creating bootstrap completion thread [0001.755] top of bootstrap2() [0001.758] CPU: ARM Cortex A57 [0001.760] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.765] initializing platform [0001.773] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.777] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.782] Macronix QSPI chip present [0001.785] SPI device register [0001.788] init boot device [0001.791] allocating memory for boot device(SPI) [0001.795] registering boot device [0001.804] QSPI bdev is already initialized [0001.808] Enable APE clock [0001.810] Un-powergate APE partition [0001.814] of_register: registering tegra_udc to of_hal [0001.819] of_register: registering inv20628-driver to of_hal [0001.824] of_register: registering ads1015-driver to of_hal [0001.830] of_register: registering lp8557-bl-driver to of_hal [0001.836] of_register: registering bq2419x_charger to of_hal [0001.841] of_register: registering bq27441_fuel_gauge to of_hal [0001.853] gpio framework initialized [0001.856] of_register: registering tca9539_gpio to of_hal [0001.862] of_register: registering tca9539_gpio to of_hal [0001.867] of_register: registering i2c_bus_driver to of_hal [0001.873] of_register: registering i2c_bus_driver to of_hal [0001.878] of_register: registering i2c_bus_driver to of_hal [0001.884] pmic framework initialized [0001.887] of_register: registering max77620_pmic to of_hal [0001.893] regulator framework initialized [0001.897] of_register: registering tps65132_bl_driver to of_hal [0001.903] initializing target [0001.908] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.916] board ID = D78, board SKU = 0 [0001.920] Skipping Z3! [0001.925] fixed regulator driver initialized [0001.943] initializing OF layer [0001.946] NCK carveout not present [0001.949] Skipping dts_overrides [0001.953] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.970] I2C Bus Init done [0001.973] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.983] I2C Bus Init done [0001.986] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.996] I2C Bus Init done [0001.999] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.009] I2C Bus Init done [0002.012] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.022] I2C Bus Init done [0002.025] of_children_init: Ops found for compatible string maxim,max77620 [0002.035] max77620_init using irq 118 [0002.040] register 'maxim,max77620' pmic [0002.045] gpio_driver_register: register 'max77620-gpio' driver [0002.051] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.061] I2C Bus Init done [0002.065] NCK carveout not present [0002.075] Find /i2c@7000c000's alias i2c0 [0002.079] get eeprom at 1-a0, size 256, type 0 [0002.088] Find /i2c@7000c500's alias i2c2 [0002.091] get eeprom at 3-a0, size 256, type 0 [0002.096] get eeprom at 3-ae, size 256, type 0 [0002.100] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.105] I2C slave not started [0002.108] I2C write failed [0002.111] Writing offset failed [0002.114] eeprom_init: EEPROM read failed [0002.118] pm_ids_update: eeprom init failed [0002.122] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.152] pm_ids_update: The pm board id is 3448-0000-400 [0002.159] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.168] pm_ids_update: pm id update successful [0002.172] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.202] pm_ids_update: The pm board id is 3449-0000-400 [0002.208] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.216] pm_ids_update: pm id update successful [0002.247] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.253] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.260] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.266] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.275] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ec:39:dc [0002.281] Plugin Manager: Parse ODM data 0x000a4000 [0002.293] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.308] Find /i2c@7000c000's alias i2c0 [0002.312] get eeprom at 1-a0, size 256, type 0 [0002.321] Find /i2c@7000c500's alias i2c2 [0002.325] get eeprom at 3-a0, size 256, type 0 [0002.329] get eeprom at 3-ae, size 256, type 0 [0002.334] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.339] I2C slave not started [0002.342] I2C write failed [0002.345] Writing offset failed [0002.348] eeprom_init: EEPROM read failed [0002.352] pm_ids_update: eeprom init failed [0002.356] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.386] pm_ids_update: The pm board id is 3448-0000-400 [0002.392] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.399] pm_ids_update: pm id update successful [0002.403] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.434] pm_ids_update: The pm board id is 3449-0000-400 [0002.440] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.447] pm_ids_update: pm id update successful [0002.477] Add serial number:1423519045845 as DT property [0002.485] Applying platform configs [0002.492] platform-init is not present. Skipping [0002.496] calling apps_init() [0002.502] Couldn't find GPT header [0002.507] Proceeding to Cold Boot [0002.510] starting app android_boot_app [0002.513] Device state: unlocked [0002.517] display console init [0002.525] could not find regulator [0002.528] hdmi cable connected [0002.544] edid read success [0002.559] edid rDT entry for leds-pwm not found e[0002.567] ad success [0002.569] width = 640, height = 480, frequency = 25174825 [0002.574] width = 640, height = 480, frequency = 25174825 [0002.579] width = 640, height = 480, frequency = 25174825 [0002.585] width = 1920, height = 1080, frequency = 148500000 [0002.590] width = 1920, height = 540, frequency = 74250000 [0002.596] width = 640, height = 480, frequency = 25174825 [0002.601] width = 720, height = 480, frequency = 26973026 [0002.607] width = 720, height = 480, frequency = 26973026 [0002.612] width = 1280, height = 720, frequency = 74175824 [0002.618] width = 1920, height = 1080, frequency = 148351648 [0002.623] width = 720, height = 576, frequency = 26973026 [0002.629] width = 720, height = 576, frequency = 26973026 [0002.634] width = 1280, height = 720, frequency = 74175824 [0002.639] width = 1920, height = 1080, frequency = 148351648 [0002.645] Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.653] tmds-config node not found [0002.657] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0002.672] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.679] could not find regulator [0002.683] could not find regulator [0002.686] could not find regulator [0002.714] using default cmu settings [0002.718] dc_hdmi_enable, starting HDMI initialisation [0002.724] dc_hdmi_enable, HDMI initialisation complete [0002.729] list and configure display window [0002.738] display console init completed [0002.749] subnode volume_up is not found ! [0002.753] subnode back is not found ! [0002.757] subnode volume_down is not found ! [0002.761] subnode menu is not found ! [0002.764] Gpio keyboard init success [0002.845] found decompressor handler: lz4-legacy [0002.859] decompressing blob (type 1)... [0002.929] load_bmp_blob: panelresolution=1080 type=3 [0003.004] decompressor handler not found [0003.008] load_firmware_blob: Firmware blob loaded, entries=2 [0003.013] XUSB blob version 0 size 124416 @ 0x934ae28c [0003.019] -------> se_aes_verify_sbk_clear: 747 [0003.024] se_aes_verify_sbk_clear: Error [0003.028] SE operation failed [0003.030] bl_battery_charging: connected to external power supply [0003.043] device_query_partition_size: failed to open partition spiflash0:MSC ! [0003.050] MSC Partition not found [0003.056] device_query_partition_size: failed to open partition spiflash0:USP ! [0003.064] USP partition read failed! [0003.067] blob_init: blob-partition USP header read failed [0003.073] android_boot Unable to update recovery partition [0003.078] kfs_getpartname: name = LNX [0003.082] Loading kernel from LNX [0003.091] Found 19 BFS partitions in "spiflash0" [0003.414] load kernel from storage [0003.419] decompressor handler not found [0003.687] Successfully loaded kernel and ramdisk images [0003.692] board ID = D78, board SKU = 0 [0003.697] sdmmc node status = okay [0003.700] sdcard instance = 0 [0003.703] sdcard gpio handle 0x5b [0003.706] sdcard gpio pin 0xc9 [0003.709] sdcard gpio flags 0x0 [0003.712] vmmc-supply 0x9e [0003.715] cd_gpio_pin = 201 [0003.717] pin_state = 0 [0003.720] Found sdcard [0003.722] SD-card IS present ... [0003.725] load_and_boot_kernel: SD card detected OK [0003.731] load_bmp_blob: panelresolution=1080 type=3 [0004.225] display bmp image done [0004.228] NCK carveout not present [0004.232] Skipping dts_overrides [0004.235] NCK carveout not present [0004.245] Find /i2c@7000c000's alias i2c0 [0004.248] get eeprom at 1-a0, size 256, type 0 [0004.257] Find /i2c@7000c500's alias i2c2 [0004.261] get eeprom at 3-a0, size 256, type 0 [0004.266] get eeprom at 3-ae, size 256, type 0 [0004.270] pm_ids_update: Updating 1,a0, size 256, type 0 [0004.275] I2C slave not started [0004.278] I2C write failed [0004.281] Writing offset failed [0004.284] eeprom_init: EEPROM read failed [0004.288] pm_ids_update: eeprom init failed [0004.292] pm_ids_update: Updating 3,a0, size 256, type 0 [0004.322] pm_ids_update: The pm board id is 3448-0000-400 [0004.329] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0004.338] pm_ids_update: pm id update successful [0004.342] pm_ids_update: Updating 3,ae, size 256, type 0 [0004.372] pm_ids_update: The pm board id is 3449-0000-400 [0004.378] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0004.386] pm_ids_update: pm id update successful [0004.417] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.422] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0004.430] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.436] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0004.444] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ec:39:dc [0004.451] Plugin Manager: Parse ODM data 0x000a4000 [0004.463] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0004.472] Add serial number:1423519045845 as DT property [0004.481] "bpmp" doesn't exist, creating [0004.486] Updated bpmp info to DTB [0004.491] Updated initrd info to DTB [0004.494] "proc-board" doesn't exist, creating [0004.501] Updated board info to DTB [0004.504] "pmu-board" doesn't exist, creating [0004.510] Updated board info to DTB [0004.513] "display-board" doesn't exist, creating [0004.519] Updated board info to DTB [0004.523] "reset" doesn't exist, creating [0004.527] Updated reset info to DTB [0004.531] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 [0004.570] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0004.575] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0004.588] Updated bootarg info to DTB [0004.592] Adding uuid 000000016445c84604000000050403c0 to DT [0004.598] Adding eks info 0 to DT [0004.604] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0004.610] Updated memory info to DTB [0004.618] set vdd_core voltage to 1075 mv [0004.621] setting 'vdd-core' regulator to 1075000 micro volts [0004.627] Found secure-pmc; disable BPMP U-Boot 2020.04-g6b630d64fd (Jan 15 2021 - 14:33:20 -0800) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 1096 bytes read in 26 ms (41 KiB/s) L4T boot options 1:primary kernel 2:overlayfs Enter choice: