[0044.967] I> MB1 (version: 0.11.0.0-t234-54845784-7fb1fa27)
[0044.973] I> t234-A01-0-Silicon (0x12347) Prod
[0044.977] I> Boot-mode : BPMP Diagnostic
[0044.981] I> Emulation:
[0044.983] I> Entry timestamp: 0x00000000
[0044.987] I> last_boot_error: 0x0
[0044.990] I> BR-BCT: preprod_dev_sign: 0
[0044.994] I> rst_source: 0x0, rst_level: 0x0
[0044.998] I> Task: Clocks enable (0x50011b9d)
[0045.002] I> Task: Crypto init (0x50018df5)
[0045.006] I> Task: Secure debug controls (0x5000c76d)
[0045.011] E> Error: ECID of check failed!!
[0045.015] E> Error: ECID of check failed!!
[0045.019] E> Error: ECID of check failed!!
[0045.023] E> Error: ECID of check failed!!
[0045.027] I> Task: Program NV master stream id (0x5000c725)
[0045.032] I> Task: Verify boot mode (0xd482021)
[0045.040] I> Task: Alias fuses (0x5000ecd5)
[0045.045] E> FUSE_ALIAS: Fuse alias on production fused part is not supported.
[0045.052] I> Task: 0x5000e911
[0045.054] I> FUSE_OPT_CCPLEX_CLUSTER_DISABLE = 0x00000000
[0045.060] I> FUSE_OPT_GPC_DISABLE = 0x00000000
[0045.064] I> FUSE_OPT_DLA_DISABLE = 0x00000000
[0045.068] I> FUSE_OPT_EMC_DISABLE = 0x00000000
[0045.072] I> FUSE_BOOTROM_PATCH_VERSION = 0x7
[0045.077] I> FUSE_PSCROM_PATCH_VERSION = 0x7
[0045.081] I> FUSE_OPT_ADC_CAL_FUSE_REV = 0x2
[0045.085] I> FUSE_SKU_INFO_0 = 0xd0
[0045.088] I> FUSE_OPT_SAMPLE_TYPE_0 = 0x3 PS
[0045.092] I> FUSE_PACKAGE_INFO_0 = 0x2
[0045.096] I> SKU: Perfect F0
[0045.099] I> Task: Voltage monitor (0x50011ba5)
[0045.103] I> VMON: Vmon re-calibration and fine tuning done
[0045.108] I> Task: Blockdev init (0x500157e1)
[0045.113] I> Task: UPHY init (0x5001b42d)
[0045.117] E> UPHY: UPHY lane info table is empty in MB1 BCT.
[0045.123] I> Task: Boot device init (0x5000d6a9)
[0045.127] E> Adding eMMC storage modules
[0045.131] I> Boot-device: RCM (instance: 0)
[0045.135] I> USB configuration success
[0045.638] I> Task: TSC init (0x5001c7e1)
[0045.642] I> Task: Enable WDT 5th expiry (0x5001d27d)
[0045.647] I> Task: Disable WDT globally (0x5001d2b9)
[0045.651] I> Task: I2C register (0x50000a09)
[0045.656] I> Task: Reset FSI (0x50011ba1)
[0045.659] I> Task: Enable clock-mon (0x5001c301)
[0045.675] I> FMON: Fmon re-programmed in mb1
[0045.679] I> Task: MB1 fixed firewalls (0x5001b1bd)
[0045.686] I> Task: Load MB2/Applet/FSKP (0x5001c305)
[0045.690] I> Loading MB2 Applet
[0045.693] I> Scratch RSV109: 0x00000000    active chain: 0
[0045.699] I> Slot: 0
[0045.701] I> Binary[21] block-0 (partition size: 0x50000)
[0045.706] I>  get_binary_info: Binary name: MB2-Applet
[0045.711] I> Size of crypto header is 8192
[0045.715] I> BCH load address is : 0x4004e000
[0045.719] I> Size of crypto header is 8192
[0045.723] I> BCH of MB2-Applet read from storage
[0045.728] I> BCH address is : 0x4004e000
[0045.732] I> MB2-Applet header integrity check is success
[0045.737] I> Binary magic in BCH component 0 is MB2A
[0045.742] I> component binary type is 21
[0045.745] I> Size of crypto header is 8192
[0045.758] I> MB2-Applet binary is read from storage
[0045.764] I> MB2-Applet binary integrity check is success
[0045.769] I> Binary MB2-Applet loaded successfully at 0x40000000 (0x41b80)
[0045.776] I> Task: Prepare MB2 params (0x5001c3d5)
[0045.781] I> MB2-params @ 0x40060000
[0045.784] I> BR-BCT Boot Chain Fields
[0045.788] I>    u32_non_gpio_select_boot_chain  : 0
[0045.793] I>    u32_num_boot_chains             : 0
[0045.797] I>    bf_bl_gpio_select_boot_chain_1b : 0
[0045.802] I> Task: Misc NV security settings (0x5000ca35)
[0045.807] I> NVDEC sticky bits programming done
[0045.811] I> Task: Disable/Reload WDT (0x5001d2e9)
[0045.816] I> Programmed SLCG global override := 0x0
[0045.821] I> MB1: MSS reconfig completed
I> Applet (version: 0.0.0.0-t234-54845784-6c7023cc)
I> t234-A01-0-Silicon (0x12347)
I> Emulation:
I> Entry timestamp: 0xffffffff
I> Task: Pinmux init (0x4000062d)
I> Task: Boot device init (0x400012e5)
I> Applet do storage init
I> Boot_device: QSPI_FLASH instance: 0
I> Qspi clock source : clk_m
I> QSPI-0l initialized successfully
I> qspi flash-0 params source = safe params
I> sdmmc DDR50 mode
I> sdmmc-3 params source = safe params
I> sdmmc bdev is already initialized
I> sdmmc-3 params source = safe params
E> mb2_config_storage_init_one_device: failed: Unknown device 7
I> Task: Partition Manager Init (0x40002cf5)
I> Found 57 partitions in QSPI_FLASH (instance 0)
W> Cannot find any partition table for 00000003
 > PARTITION_MANAGER: Failed to publish partition.
W> Cannot find any partition table for 00010003
 > PARTITION_MANAGER: Failed to publish partition.
I> Task: I2C register (0x400006a5)
I> Task: Register exit handlers (0x400005f5)
I> Task: Enter 3p server (0x400018b5)
I> USB configuration success
I> Populate chip info
I> RAM_CODE 0x4000001
I> Populate eeprom info
I> Populate eeprom info for module cvm
I> dump bct
I> Rebooting : reboot-recovery


E> instance 0 not supported for module 8