=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2022.02.09 08:48:52 =~=~=~=~=~=~=~=~=~=~=~= [0000.406] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de) [0000.411] Processing in cold boot mode Bootloader 2 [0000.416] A02 Bootrom Patch rev = 1023 [0000.419] Power-up reason: pmc por [0000.423] No Battery Present [0000.425] pmic max77620 reset reason [0000.429] pmic max77620 NVERC : 0x50 [0000.432] RamCode = 0 [0000.434] Platform has DDR4 type RAM [0000.438] max77620 disabling SD1 Remote Sense [0000.442] Setting DDR voltage to 1125mv [0000.446] Serial Number of Pmic Max77663: 0xc16a4 [0000.453] Entering ramdump check [0000.456] Get RamDumpCarveOut = 0x0 [0000.460] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.465] Last reboot was clean, booting normally! [0000.469] Sdram initialization is successful [0000.473] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.480] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.485] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.491] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.497] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.503] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.509] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.515] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.531] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.537] Platform-DebugCarveout: 0 [0000.540] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.546] Non secure mode, and RB not enabled. [0000.562] Csd NumOfBlocks=0 [0000.909] *** Booting BFS0. [0000.911] Read PT from (0:3) [0000.921] Using BFS PT to query partitions [0000.925] PT: Partition LNX NOT found ! [0002.164] *** Booting KFS0. [0002.167] BoardID = 3448, SKU = 0x2 [0002.170] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0002.176] Read GPT from (0:3) [0002.185] Using GPT Primary to query partitions [0002.190] Loading Tboot-CPU binary [0002.200] Verifying TBC in OdmNonSecureSBK mode [0002.210] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0002.217] Bootloader downloaded successfully. [0002.221] Downloaded Tboot-CPU binary to 0xa0000258 [0002.226] MAX77620_GPIO5 configured [0002.230] CPU power rail is up [0002.232] CPU clock enabled [0002.236] Performing RAM repair [0002.239] Updating A64 Warmreset Address to 0xa00002e9 [0002.244] BoardID = 3448, SKU = 0x2 [0002.247] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0002.254] Loading NvTbootBootloaderDTB [0002.274] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0002.337] Bootloader DTB Load Address: 0x83000000 [0002.342] BoardID = 3448, SKU = 0x2 [0002.345] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0002.351] Loading NvTbootKernelDTB [0002.371] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0002.433] Kernel DTB Load Address: 0x83100000 [0002.438] BoardID = 3448, SKU = 0x2 [0002.441] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0002.450] Loading cboot binary [0002.461] Verifying EBT in OdmNonSecureSBK mode [0002.503] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0002.510] Bootloader downloaded successfully. [0002.514] BoardID = 3448, SKU = 0x2 [0002.517] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0002.524] PT: Partition NCT NOT found ! [0002.527] Warning: Find Partition via PT Failed [0002.532] Next binary entry address: 0x92c00258 [0002.536] BoardId: 3448 [0002.541] Overriding pmu board id with proc board id [0002.546] Display board id is not available [0002.550] BoardID = 3448, SKU = 0x2 [0002.553] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0002.570] Verifying SC7EntryFw in OdmNonSecureSBK mode [0002.622] /bpmp deleted [0002.625] SC7EntryFw header found loaded at 0xff700000 [0002.799] OVR2 PMIC [0002.801] Bpmp FW successfully loaded [0002.805] BoardID = 3448, SKU = 0x2 [0002.808] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0002.817] WB0 init successfully at 0xff780000 [0002.821] Set NvDecSticky Bits [0002.825] GSC2 address ff53fffc value c0edbbcc [0002.831] GSC MC Settings done [0002.834] BoardID = 3448, SKU = 0x2 [0002.837] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0002.844] TOS Image length 53680 [0002.847] Monitor size 53680 [0002.850] OS size 0 [0002.855] Secure Os AES-CMAC Verification Success! [0002.860] TOS image cipher info: plaintext [0002.864] Loading and Validation of Secure OS Successful [0002.880] SC7 Entry Firmware - 0xff700000, 0x4000 [0002.884] NvTbootPackSdramParams: start. [0002.889] NvTbootPackSdramParams: done. [0002.893] Tegraboot started after 339659 us [0002.897] Basic modules init took 2281508 us [0002.901] Sec Bootdevice Read Time = 1386 ms, Read Size = 14649 KB [0002.907] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0002.913] Next stage binary read took 10732 us [0002.917] Carveout took -32045 us [0002.920] CPU initialization took 363247 us [0002.924] Total time taken by TegraBoot 2623442 us [0002.929] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):5b49e7f80 NOTICE: BL31: Built : 08:37:40, Feb 19 2021 ERROR: Error initializing runtime service trusty_fast [0003.051] RamCode = 0 [0003.056] LPDDR4 Training: Read DT: Number of tables = 2 [0003.061] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0003.073] EMC Training Successful [0003.076] 408000 not found in DVFS table [0003.083] RamCode = 0 [0003.086] DT Write: emc-table@204000 succeeded [0003.091] DT Write: emc-table@1600000 succeeded [0003.096] LPDDR4 Training: Write DT: Number of tables = 2 [0003.179] [0003.180] Debug Init done [0003.183] Marked DTB cacheable [0003.185] Bootloader DTB loaded at 0x83000000 [0003.190] Marked DTB cacheable [0003.193] Kernel DTB loaded at 0x83100000 [0003.197] DeviceTree Init done [0003.210] Pinmux applied successfully [0003.214] gicd_base: 0x50041000 [0003.218] gicc_base: 0x50042000 [0003.221] Interrupts Init done [0003.225] Using base:0x60005090 & irq:208 for tick-timer [0003.230] Using base:0x60005098 for delay-timer [0003.235] platform_init_timer: DONE [0003.238] Timer(tick) Init done [0003.242] osc freq = 38400 khz [0003.246] [0003.247] Welcome to L4T Cboot [0003.250] [0003.251] Cboot Version: 00.00.2018.01-t210-39562017 [0003.256] calling constructors [0003.259] initializing heap [0003.261] initializing threads [0003.264] initializing timers [0003.267] creating bootstrap completion thread [0003.272] top of bootstrap2() [0003.274] CPU: ARM Cortex A57 [0003.277] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0003.282] initializing platform [0003.337] Config for emmc ddr50 mode completed [0003.341] sdmmc bdev is already initialized [0003.345] Enable APE clock [0003.348] Un-powergate APE partition [0003.351] of_register: registering tegra_udc to of_hal [0003.356] of_register: registering inv20628-driver to of_hal [0003.362] of_register: registering ads1015-driver to of_hal [0003.368] of_register: registering lp8557-bl-driver to of_hal [0003.373] of_register: registering bq2419x_charger to of_hal [0003.379] of_register: registering bq27441_fuel_gauge to of_hal [0003.390] gpio framework initialized [0003.393] of_register: registering tca9539_gpio to of_hal [0003.399] of_register: registering tca9539_gpio to of_hal [0003.404] of_register: registering i2c_bus_driver to of_hal [0003.410] of_register: registering i2c_bus_driver to of_hal [0003.415] of_register: registering i2c_bus_driver to of_hal [0003.421] pmic framework initialized [0003.424] of_register: registering max77620_pmic to of_hal [0003.430] regulator framework initialized [0003.434] of_register: registering tps65132_bl_driver to of_hal [0003.440] initializing target [0003.445] gpio_driver_register: register 'tegra_gpio_driver' driver [0003.456] fixed regulator driver initialized [0003.472] initializing OF layer [0003.475] NCK carveout not present [0003.479] Skipping dts_overrides [0003.483] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0003.497] I2C Bus Init done [0003.500] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0003.510] I2C Bus Init done [0003.513] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0003.523] I2C Bus Init done [0003.525] of_children_init: Ops found for compatible string ti,tca9539 [0003.535] tca9539_init: i2c bus: 3, slave addr: 0xe8 [0003.542] gpio_driver_register: register 'tca9539_gpio_driver' driver [0003.548] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0003.558] I2C Bus Init done [0003.561] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0003.571] I2C Bus Init done [0003.574] of_children_init: Ops found for compatible string maxim,max77620 [0003.584] max77620_init using irq 118 [0003.588] register 'maxim,max77620' pmic [0003.593] gpio_driver_register: register 'max77620-gpio' driver [0003.599] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0003.609] I2C Bus Init done [0003.612] NCK carveout not present [0003.617] Cannot find the PM_EEPR_MNG [0003.621] no eeprom position or read error [0003.651] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0003.657] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0003.664] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0003.670] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0003.678] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3e:36:09 [0003.685] Plugin Manager: Parse ODM data 0x000a4000 [0003.696] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0003.706] Cannot find the PM_EEPR_MNG [0003.710] no eeprom position or read error [0003.739] Add serial number:1421621004284 as DT property [0003.746] Applying platform configs [0003.752] platform-init is not present. Skipping [0003.757] calling apps_init() [0003.779] Found 17 GPT partitions in "sdmmc3_user" [0003.783] Proceeding to Cold Boot [0003.787] starting app android_boot_app [0003.790] Device state: unlocked [0003.793] display console init [0003.802] could not find regulator [0003.825] hdmi cable not connected [0003.828] is_hdmi_needed: HDMI not connected, returning false [0003.834] hdmi is not connected [0[0003.840] DT entry for leds-pwm not found 003.837] sor0 is not supported [0003.846] display_console_init: no valid display out_type [0003.854] subnode volume_up is not found ! [0003.858] subnode back is not found ! [0003.861] subnode volume_down is not found ! [0003.866] subnode menu is not found ! [0003.869] Gpio keyboard init success [0003.918] found decompressor handler: lz4-legacy [0003.933] decompressing blob (type 1)... [0003.999] display_resolution: No display init [0004.003] Failed to retrieve display resolution [0004.008] Could not load/initialize BMP blob...ignoring [0004.059] decompressor handler not found [0004.063] load_firmware_blob: Firmware blob loaded, entries=2 [0004.068] XUSB blob version 0 size 124416 @ 0x92cb328c [0004.074] -------> se_aes_verify_sbk_clear: 747 [0004.079] se_aes_verify_sbk_clear: Error [0004.083] SE operation failed [0004.085] bl_battery_charging: connected to external power supply [0004.094] display_console_ioctl: No display init [0004.099] switch_backlight failed [0004.109] device_query_partition_size: failed to open partition sdmmc3_user:MSC ! [0004.116] MSC Partition not found [0004.126] device_query_partition_size: failed to open partition sdmmc3_user:USP ! [0004.133] USP partition read failed! [0004.137] blob_init: blob-partition USP header read failed [0004.142] android_boot Unable to update recovery partition [0004.148] kfs_getpartname: name = LNX [0004.151] Loading kernel from LNX [0004.249] load kernel from storage [0004.260] decompressor handler not found [0004.293] Successfully loaded kernel and ramdisk images [0004.298] board ID = D78, board SKU = 2 [0004.303] display_resolution: No display init [0004.307] Failed to retrieve display resolution [0004.312] bmp blob is not loaded and initialized [0004.316] Failed to display boot-logo [0004.320] NCK carveout not present [0004.323] Skipping dts_overrides [0004.326] NCK carveout not present [0004.332] Cannot find the PM_EEPR_MNG [0004.335] no eeprom position or read error [0004.365] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.371] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0004.378] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0004.384] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0004.392] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3e:36:09 [0004.399] Plugin Manager: Parse ODM data 0x000a4000 [0004.410] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0004.418] Add serial number:1421621004284 as DT property [0004.426] "bpmp" doesn't exist, creating [0004.432] Updated bpmp info to DTB [0004.436] Updated initrd info to DTB [0004.440] "proc-board" doesn't exist, creating [0004.446] Updated board info to DTB [0004.449] "pmu-board" doesn't exist, creating [0004.455] Updated board info to DTB [0004.458] "display-board" doesn't exist, creating [0004.464] Updated board info to DTB [0004.467] "reset" doesn't exist, creating [0004.472] Updated reset info to DTB [0004.475] display_console_ioctl: No display init [0004.480] display_console_ioctl: No display init [0004.484] display_console_ioctl: No display init [0004.489] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt [0004.523] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0004.529] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 [0004.545] Updated bootarg info to DTB [0004.549] Adding uuid 00000001643146c10800000007010240 to DT [0004.555] Adding eks info 0 to DT [0004.560] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0004.566] Updated memory info to DTB [0004.570] add_lp0_disable: Unable to find plugin-manager ids under chosen node! (FDT_ERR_NOTFOUND) [0004.582] set vdd_core voltage to 1075 mv [0004.586] setting 'vdd-core' regulator to 1075000 micro volts [0004.592] Found secure-pmc; disable BPMP U-Boot 2020.04-g6b630d64fd (Feb 19 2021 - 08:37:46 -0800) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... *** Warning - spi_flash_probe_bus_cs() failed, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  1  0 Card did not respond to voltage select! switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 879 bytes read in 22 ms (38.1 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 7159841 bytes read in 178 ms (38.4 MiB/s) Retrieving file: /boot/Image 34338824 bytes read in 779 ms (42 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000083100000, end 00000000831752f5 copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.201-tegra (buildbrain@mobile-u64-5294-d8000) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Fri Feb 19 08:40:32 PST 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.528059] genirq: Setting trigger mode 8 for irq 57 failed (irq_chip_set_type_parent+0x0/0x48) [ 1.055157] tegradc tegradc.1: tegra_dc_parse_panel_ops: could not find panel for /host1x/sor [ 1.055195] tegradc tegradc.1: err:-19 parsing panel_ops [ 1.117107] nct1008_nct72 0-004c: write reg err -121 [ 1.122211] nct1008_nct72 0-004c: sensor init failed 0xffffff87 [ 1.128183] nct1008_nct72 0-004c: [ 1.128183] exit nct1008_probe, err=-121 [ 1.366621] mmc0: error -110 whilst initialising MMC card [ 1.375643] sdhci-tegra sdhci-tegra.3: Failed to set parent pll 32770 [ 1.496236] mmc0: error -110 whilst initialising MMC card [ 1.503039] sdhci-tegra sdhci-tegra.3: Failed to set parent pll 32770 [ 1.626602] mmc0: error -110 whilst initialising MMC card [ 1.633111] sdhci-tegra sdhci-tegra.3: Failed to set parent pll 32770 [ 1.790982] mmc0: error -110 whilst initialising MMC card