[0000.398] [L4T TegraBoot] (version 00.00.2018.01-l4t-8728f3cb) [0000.404] Processing in cold boot mode Bootloader 2 [0000.408] A02 Bootrom Patch rev = 1023 [0000.412] Power-up reason: pmc por [0000.415] No Battery Present [0000.418] pmic max77620 reset reason [0000.421] pmic max77620 NVERC : 0x50 [0000.425] RamCode = 0 [0000.427] Platform has DDR4 type RAM [0000.430] max77620 disabling SD1 Remote Sense [0000.434] Setting DDR voltage to 1125mv [0000.438] Serial Number of Pmic Max77663: 0x2020b1 [0000.446] Entering ramdump check [0000.449] Get RamDumpCarveOut = 0x0 [0000.452] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.457] Last reboot was clean, booting normally! [0000.462] Sdram initialization is successful [0000.466] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.472] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.478] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.484] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.490] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.496] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.501] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.507] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.523] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.529] Platform-DebugCarveout: 0 [0000.533] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.539] Non secure mode, and RB not enabled. [0000.543] *** Booting BFS0. [0000.545] Initialize FailControl [0000.548] Read PT from (0:3) [0000.563] Csd NumOfBlocks=0 [0000.603] PT crc32 and magic check passed. [0000.606] Using BFS PT to query partitions [0000.611] PT: Partition LNX NOT found ! [0000.614] *** Booting KFS0. [0000.617] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.623] BoardID = 3448, SKU = 0x2 [0000.626] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0000.632] Read GPT from (0:3) [0000.640] Using GPT Primary to query partitions [0000.645] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.651] Loading Tboot-CPU binary [0000.657] Verifying TBC in OdmNonSecureSBK mode [0000.667] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.674] Bootloader downloaded successfully. [0000.678] Downloaded Tboot-CPU binary to 0xa0000258 [0000.683] MAX77620_GPIO5 configured [0000.686] CPU power rail is up [0000.689] CPU clock enabled [0000.693] Performing RAM repair [0000.696] Updating A64 Warmreset Address to 0xa00002e9 [0000.701] BoardID = 3448, SKU = 0x2 [0000.704] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0000.710] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.716] Loading NvTbootBootloaderDTB [0000.733] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.805] Bootloader DTB Load Address: 0x83000000 [0000.810] BoardID = 3448, SKU = 0x2 [0000.813] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0000.819] Loading NvTbootKernelDTB [0000.851] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.922] Kernel DTB Load Address: 0x83100000 [0000.927] BoardID = 3448, SKU = 0x2 [0000.930] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0000.936] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.943] Loading cboot binary [0000.954] Verifying EBT in OdmNonSecureSBK mode [0000.996] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0001.003] Bootloader downloaded successfully. [0001.007] BoardID = 3448, SKU = 0x2 [0001.010] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0001.016] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.023] PT: Partition NCT NOT found ! [0001.026] Warning: Find Partition via PT Failed [0001.031] Next binary entry address: 0x92c00258 [0001.035] BoardId: 3448 [0001.051] NvTbootI2cWaitForTransferComplete(): error code 0x00000005 I2C Transaction could not complete within time [0001.072] NvTbootI2cWaitForTransferComplete(): error code 0x00000005 I2C Transaction could not complete within time [0001.082] NvTbootI2cWrite(): error code 0x00000005 Error while starting write transaction [0001.089] NvTbootI2cDeviceRead(): error code 0x00045001 Error while sending the offset to slave [0001.098] NvTbootI2c: Read failed for slave 0xaa, offset 0x00 with error code 0x00045001 [0001.106] Overriding pmu board id with proc board id [0001.121] NvTbootI2cWaitForTransferComplete(): error code 0x00000005 I2C Transaction could not complete within time [0001.142] NvTbootI2cWaitForTransferComplete(): error code 0x00000005 I2C Transaction could not complete within time [0001.152] NvTbootI2cWrite(): error code 0x00000005 Error while starting write transaction [0001.159] NvTbootI2cDeviceRead(): error code 0x00045001 Error while sending the offset to slave [0001.168] NvTbootI2c: Read failed for slave 0xa2, offset 0x00 with error code 0x00045001 [0001.176] Display board id is not available [0001.180] BoardID = 3448, SKU = 0x2 [0001.183] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0001.189] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.203] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.259] /bpmp deleted [0001.261] SC7EntryFw header found loaded at 0xff700000 [0001.448] OVR2 PMIC [0001.450] Bpmp FW successfully loaded [0001.454] BoardID = 3448, SKU = 0x2 [0001.457] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0001.463] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.470] WB0 init successfully at 0xff780000 [0001.474] Verifying NvTbootWb0 in OdmNonSecureSBK mode [0001.480] Set NvDecSticky Bits [0001.483] GSC2 address ff53fffc value c0edbbcc [0001.489] GSC MC Settings done [0001.492] BoardID = 3448, SKU = 0x2 [0001.496] Not Nano-SD or !QSPI-ONLY, check GPT table first ... [0001.502] TOS Image length 53680 [0001.505] Monitor size 53680 [0001.508] OS size 0 [0001.513] Secure Os AES-CMAC Verification Success! [0001.518] TOS image cipher info: plaintext [0001.522] Loading and Validation of Secure OS Successful [0001.538] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.542] NvTbootPackSdramParams: start. [0001.547] NvTbootPackSdramParams: done. [0001.551] Tegraboot started after 151996 us [0001.555] Basic modules init took 1072549 us [0001.559] Sec Bootdevice Read Time = 70 ms, Read Size = 3682 KB [0001.565] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.571] Next stage binary read took 7365 us [0001.575] Carveout took -169200 us [0001.578] CPU initialization took 526192 us [0001.582] Total time taken by TegraBoot 1436906 us [0001.587] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):b5eeb33f7 NOTICE: BL31: Built : 12:09:37, Jul 26 2021 ERROR: Error initializing runtime service trusty_fast [0001.709] RamCode = 0 [0001.714] LPDDR4 Training: Read DT: Number of tables = 2 [0001.719] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.731] EMC Training Successful [0001.734] 408000 not found in DVFS table [0001.741] RamCode = 0 [0001.744] DT Write: emc-table@204000 succeeded [0001.750] DT Write: emc-table@1600000 succeeded [0001.754] LPDDR4 Training: Write DT: Number of tables = 2 [0001.805] [0001.806] Debug Init done [0001.808] Marked DTB cacheable [0001.811] Bootloader DTB loaded at 0x83000000 [0001.816] Marked DTB cacheable [0001.819] Kernel DTB loaded at 0x83100000 [0001.823] DeviceTree Init done [0001.836] Pinmux applied successfully [0001.840] gicd_base: 0x50041000 [0001.844] gicc_base: 0x50042000 [0001.847] Interrupts Init done [0001.851] Using base:0x60005090 & irq:208 for tick-timer [0001.856] Using base:0x60005098 for delay-timer [0001.861] platform_init_timer: DONE [0001.864] Timer(tick) Init done [0001.868] osc freq = 38400 khz [0001.872] [0001.873] Welcome to L4T Cboot [0001.876] [0001.877] Cboot Version: 00.00.2018.01-t210-c952b4e6 [0001.882] calling constructors [0001.885] initializing heap [0001.887] initializing threads [0001.890] initializing timers [0001.893] creating bootstrap completion thread [0001.898] top of bootstrap2() [0001.901] CPU: ARM Cortex A57 [0001.903] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.908] initializing platform [0001.962] Config for emmc ddr50 mode completed [0001.966] sdmmc bdev is already initialized [0001.970] Enable APE clock [0001.973] Un-powergate APE partition [0001.976] of_register: registering tegra_udc to of_hal [0001.981] of_register: registering inv20628-driver to of_hal [0001.987] of_register: registering ads1015-driver to of_hal [0001.993] of_register: registering lp8557-bl-driver to of_hal [0001.998] of_register: registering bq2419x_charger to of_hal [0002.004] of_register: registering bq27441_fuel_gauge to of_hal [0002.015] gpio framework initialized [0002.019] of_register: registering tca9539_gpio to of_hal [0002.024] of_register: registering tca9539_gpio to of_hal [0002.029] of_register: registering i2c_bus_driver to of_hal [0002.035] of_register: registering i2c_bus_driver to of_hal [0002.041] of_register: registering i2c_bus_driver to of_hal [0002.046] pmic framework initialized [0002.050] of_register: registering max77620_pmic to of_hal [0002.055] regulator framework initialized [0002.059] of_register: registering tps65132_bl_driver to of_hal [0002.065] initializing target [0002.071] gpio_driver_register: register 'tegra_gpio_driver' driver [0002.081] fixed regulator driver initialized [0002.099] initializing OF layer [0002.102] NCK carveout not present [0002.105] Skipping dts_overrides [0002.109] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.125] I2C Bus Init done [0002.128] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.138] I2C Bus Init done [0002.141] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.151] I2C Bus Init done [0002.154] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.164] I2C Bus Init done [0002.167] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.177] I2C Bus Init done [0002.180] of_children_init: Ops found for compatible string maxim,max77620 [0002.190] max77620_init using irq 118 [0002.195] register 'maxim,max77620' pmic [0002.199] gpio_driver_register: register 'max77620-gpio' driver [0002.205] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.215] I2C Bus Init done [0002.219] NCK carveout not present [0002.228] Find /i2c@7000c000's alias i2c0 [0002.232] get eeprom at 1-a0, size 256, type 0 [0002.241] Find /i2c@7000c500's alias i2c2 [0002.245] get eeprom at 3-a0, size 256, type 0 [0002.249] get eeprom at 3-ae, size 256, type 0 [0002.253] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.302] I2C slave not started [0002.305] I2C write failed [0002.307] Writing offset failed [0002.310] eeprom_init: EEPROM read failed [0002.314] pm_ids_update: eeprom init failed [0002.318] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.349] pm_ids_update: The pm board id is 3448-0002-400 [0002.355] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0002.364] pm_ids_update: pm id update successful [0002.368] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.374] I2C slave not started [0002.377] I2C write failed [0002.379] Writing offset failed [0002.382] eeprom_init: EEPROM read failed [0002.386] pm_ids_update: eeprom init failed [0002.416] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.422] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.430] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.436] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.444] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3e:36:2d [0002.450] Plugin Manager: Parse ODM data 0x000a4000 [0002.463] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.477] Find /i2c@7000c000's alias i2c0 [0002.481] get eeprom at 1-a0, size 256, type 0 [0002.490] Find /i2c@7000c500's alias i2c2 [0002.494] get eeprom at 3-a0, size 256, type 0 [0002.498] get eeprom at 3-ae, size 256, type 0 [0002.502] pm_ids_update: Updating 1,a0, size 256, type 0 [0004.508] I2C transfer timeout [0004.511] I2C write failed [0004.513] Writing offset failed [0004.516] eeprom_init: EEPROM read failed [0004.520] pm_ids_update: eeprom init failed [0004.524] pm_ids_update: Updating 3,a0, size 256, type 0 [0004.554] pm_ids_update: The pm board id is 3448-0002-400 [0004.561] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0004.568] pm_ids_update: pm id update successful [0004.572] pm_ids_update: Updating 3,ae, size 256, type 0 [0004.578] I2C slave not started [0004.581] I2C write failed [0004.583] Writing offset failed [0004.586] eeprom_init: EEPROM read failed [0004.590] pm_ids_update: eeprom init failed [0004.620] Add serial number:1421621003359 as DT property [0004.628] Applying platform configs [0004.634] platform-init is not present. Skipping [0004.639] calling apps_init() [0004.660] Found 17 GPT partitions in "sdmmc3_user" [0004.665] Proceeding to Cold Boot [0004.668] starting app android_boot_app [0004.672] Device state: unlocked [0004.675] display console init [0004.683] could not find regulator [0004.686] hdmi cable connected [0004.702] edid read success [0004.716] DT entry for leds-pwm not found [0004.721] edid read success [0004.723] width = 640, height = 480, frequency = 25174825 [0004.729] width = 640, height = 480, frequency = 25174825 [0004.734] width = 2560, height = 1440, frequency = 241500000 [0004.740] width = 1920, height = 1080, frequency = 148500000 [0004.745] width = 640, height = 480, frequency = 25174825 [0004.751] width = 720, height = 480, frequency = 26973026 [0004.756] width = 1280, height = 720, frequency = 74175824 [0004.762] width = 1920, height = 1080, frequency = 148351648 [0004.767] width = 720, height = 576, frequency = 26973026 [0004.773] width = 1280, height = 720, frequency = 74175824 [0004.778] width = 1920, height = 1080, frequency = 148351648 [0004.784] width = 1920, height = 1080, frequency = 74175824 [0004.789] width = 3840, height = 2160, frequency = 296703296 [0004.795] width = 3840, height = 2160, frequency = 296703296 [0004.801] width = 3840, height = 2160, frequency = 296703296 [0004.806] width = 3840, height = 2160, frequency = 296703296 [0004.812] Best mode Width = 1920, Height = 1080, freq = 148351648 [0004.820] tmds-config node not found [0004.824] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0004.838] setting 'vdd-1v8' regulator to 1800000 micro volts [0004.846] could not find regulator [0004.849] could not find regulator [0004.853] could not find regulator [0004.881] using default cmu settings [0004.884] dc_hdmi_enable, starting HDMI initialisation [0004.891] dc_hdmi_enable, HDMI initialisation complete [0004.896] list and configure display window [0004.904] display console init completed [0004.915] subnode volume_up is not found ! [0004.919] subnode back is not found ! [0004.923] subnode volume_down is not found ! [0004.927] subnode menu is not found ! [0004.931] Gpio keyboard init success [0004.979] found decompressor handler: lz4-legacy [0004.993] decompressing blob (type 1)... [0005.063] load_bmp_blob: panelresolution=1080 type=3 [0005.112] decompressor handler not found [0005.116] load_firmware_blob: Firmware blob loaded, entries=2 [0005.122] XUSB blob version 0 size 126464 @ 0x934b928c [0005.128] -------> se_aes_verify_sbk_clear: 747 [0005.132] se_aes_verify_sbk_clear: Error [0005.136] SE operation failed [0005.139] bl_battery_charging: connected to external power supply [0005.154] device_query_partition_size: failed to open partition sdmmc3_user:MSC ! [0005.162] MSC Partition not found [0005.171] device_query_partition_size: failed to open partition sdmmc3_user:USP ! [0005.179] USP partition read failed! [0005.182] blob_init: blob-partition USP header read failed [0005.188] android_boot Unable to update recovery partition [0005.193] kfs_getpartname: name = LNX [0005.197] Loading kernel from LNX [0005.287] load kernel from storage [0005.296] decompressor handler not found [0005.329] Successfully loaded kernel and ramdisk images [0005.335] board ID = D78, board SKU = 2 [0005.339] load_bmp_blob: panelresolution=1080 type=3 [0005.835] display bmp image done [0005.838] NCK carveout not present [0005.842] Skipping dts_overrides [0005.845] NCK carveout not present [0005.854] Find /i2c@7000c000's alias i2c0 [0005.858] get eeprom at 1-a0, size 256, type 0 [0005.867] Find /i2c@7000c500's alias i2c2 [0005.871] get eeprom at 3-a0, size 256, type 0 [0005.875] get eeprom at 3-ae, size 256, type 0 [0005.879] pm_ids_update: Updating 1,a0, size 256, type 0 [0007.885] I2C transfer timeout [0007.888] I2C write failed [0007.890] Writing offset failed [0007.893] eeprom_init: EEPROM read failed [0007.897] pm_ids_update: eeprom init failed [0007.901] pm_ids_update: Updating 3,a0, size 256, type 0 [0007.931] pm_ids_update: The pm board id is 3448-0002-400 [0007.938] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0007.947] pm_ids_update: pm id update successful [0007.951] pm_ids_update: Updating 3,ae, size 256, type 0 [0007.957] I2C slave not started [0007.960] I2C write failed [0007.962] Writing offset failed [0007.965] eeprom_init: EEPROM read failed [0007.969] pm_ids_update: eeprom init failed [0007.999] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0008.005] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0008.013] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0008.019] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0008.027] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3e:36:2d [0008.033] Plugin Manager: Parse ODM data 0x000a4000 [0008.046] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0008.054] Add serial number:1421621003359 as DT property [0008.063] "bpmp" doesn't exist, creating [0008.068] Updated bpmp info to DTB [0008.073] Updated initrd info to DTB [0008.076] "proc-board" doesn't exist, creating [0008.083] Updated board info to DTB [0008.086] "pmu-board" doesn't exist, creating [0008.092] Updated board info to DTB [0008.095] "display-board" doesn't exist, creating [0008.101] Updated board info to DTB [0008.104] "reset" doesn't exist, creating [0008.109] Updated reset info to DTB [0008.113] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92cb4000 is_hdmi_initialised=1 [0008.152] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0008.157] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 [0008.174] Updated bootarg info to DTB [0008.178] Adding uuid 00000001643174061800000018fc0300 to DT [0008.183] Adding eks info 0 to DT [0008.189] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0008.195] Updated memory info to DTB [0008.203] set vdd_core voltage to 1075 mv [0008.206] setting 'vdd-core' regulator to 1075000 micro volts [0008.212] Found secure-pmc; disable BPMP U-Boot 2020.04-g46e4604c78 (Jul 26 2021 - 12:09:42 -0700) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 Card did not respond to voltage select! switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 879 bytes read in 24 ms (35.2 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 7160133 bytes read in 177 ms (38.6 MiB/s) Retrieving file: /boot/Image 34615304 bytes read in 783 ms (42.2 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92cb4000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000083100000, end 000000008317cf40 copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.253-tegra (blurpd@blurpd-HP-ProDesk-600-G3-DM) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Wed Sep 29 10:00:11 EDT 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00800000@92cb4000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 1.159037] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.305435] imx219 7-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.305499] imx219 7-0010: board setup failed [ 1.329343] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.329407] imx219 8-0010: board setup failed [ 1.683339] cgroup: cgroup2: unknown option "nsdelegate" [ 2.046221] usb 1-3: device not accepting address 3, error -71 [ 2.586225] usb 1-3: device not accepting address 4, error -71 [ 2.724749] using random self ethernet address [ 2.729668] using random host ethernet address [ 3.050253] using random self ethernet address [ 3.055157] using random host ethernet address [ 3.235902] random: crng init done [ 3.239334] random: 7 urandom warning(s) missed due to ratelimiting [ 4.194344] usb 1-3: device descriptor read/64, error -71 [ 4.210228] tegra_cec 70015000.tegra_cec: timeout in tegra_cec_native_write_l:172. [ 4.229979] tegra_cec 70015000.tegra_cec: Sent res: -62. [ 4.238888] tegra_cec 70015000.tegra_cec: tegra_cec_init Done. [ 4.426322] usb 1-3: device descriptor read/64, error -71 [ 4.778340] usb 1-3: device descriptor read/64, error -71 [ 5.010377] usb 1-3: device descriptor read/64, error -71 [ 5.122325] usb usb1-port3: unable to enumerate USB device [ 5.370804] usb 1-3: Device not responding to setup address. [ 5.582757] usb 1-3: Device not responding to setup address. [ 5.794219] usb 1-3: device not accepting address 7, error -71 [ 5.919064] usb 1-3: Device not responding to setup address. [ 6.131073] usb 1-3: Device not responding to setup address. [ 6.342213] usb 1-3: device not accepting address 8, error -71 [ 7.942317] usb 1-3: device descriptor read/64, error -71 [ 8.178339] usb 1-3: device descriptor read/64, error -71 [ 8.538653] usb 1-3: device descriptor read/64, error -71 [ 8.770557] usb 1-3: device descriptor read/64, error -71 [ 8.882333] usb usb1-port3: unable to enumerate USB device [ 9.326235] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 10.643451] Please complete system configuration setup on desktop to proceed... [ 13.410331] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [