paro@tegra-ubuntu:~$ [0146.439] Enabled early print
[0146.441] [TegraBoot] (version 00.00.2018.01-l4t-9867942c)
[0146.447] Processing in recovery mode
[0146.450] A02 Bootrom Patch rev = 63
[0146.453] Power-up reason: pmc por
[0146.457] Established communication link with host
[0147.693] NvTbootI2cWrite(): error code 0x00045100 Error while starting write transaction
[0147.701] NvTbootI2cDeviceRead(): error code 0x00045001 Error while sending the offset to slave
[0147.709] NvTbootI2c: Read failed for slave 0xac, offset 0x00 with error code 0x00045001
[0173.781] Odmdata from BCT: 0x00094000
[0173.785] DebugPort= 0x3
[0173.787] BoardId read from EEPROM/NCT: 2180
[0173.816] Turned on fan for loki board
[0173.819] Key release before reqd. time for fastboot
[0173.824] No Battery Present
[0173.827] RamCode = 0
[0173.829] Platform has Ddr4 type ram
[0173.832] max77620 disabling SD1 Remote Sense
[0173.837] Setting Ddr voltage to 1125mv
[0173.841] Serial Number of Pmic Max77663: 0xb09b5
[0173.848] Entering ramdump check
[0173.851] Get RamDumpCarveOut = 0x0
[0173.855] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0173.860] Last reboot was clean, booting normally!
[0173.864] Sdram initialization is successful 
[0173.868] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0173.875] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0173.880] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0173.886] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0173.892] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0173.898] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0173.904] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0173.910] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0173.926] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0173.932] Platform-DebugCarveout: 0
[0173.935] Downloaded BCT successfully
[0174.300] Downloaded Bootloader successfully
[0174.409] Downloaded rp1 successfully
[0174.670] MAX77620_GPIO1 Configured.
[0174.674] MAX77620_GPIO5 Configured.
[0174.677] CPU power rail is up
[0174.680] CPU clock enabled
[0174.684] Performing RAM repair
[0174.687] Updating A64 Warmreset Address to 0x92c002e9
[0174.693] Enable APE clock/reset
[0174.696] Error in NvTbootGetTOSBinaryLength: 0x11 !
[0174.701] Loading Secure OS image failed. 
[0174.705] Set NvDecSticky Bits
[0174.708] GSC2 address ff53fffc value c0edbbcc
[0174.715] GSC MC Settings done
[0174.719] Next binary entry address: 0x92c00258 
[0174.723] BoardId: 2180
[0174.726] Rail not supported
[0174.729] Starting CPU & Halting co-processor 

[0178.933] 
[0178.934] Debug Init done
[0178.937] Marked DTB cacheable
[0178.940] Bootloader DTB loaded at 0x83000400
[0178.945] DeviceTree Init done
[0178.959] Pinmux applied successfully
[0178.964] gicd_base: 0x50041000
[0178.968] gicc_base: 0x50042000
[0178.971] Interrupts Init done
[0178.975] Using base:0x60005090 & irq:208 for tick-timer
[0178.980] Using base:0x60005098 for delay-timer
[0178.985] platform_init_timer: DONE
[0178.988] Timer(tick) Init done
[0178.993] osc freq = 38400 khz
[0178.997] 
[0178.998] welcome to cboot
[0179.001] 
[0179.002] Cboot Version: 00.00.2018.01-t210-29b0d242
[0179.007] calling constructors
[0179.010] initializing heap
[0179.013] initializing threads
[0179.016] initializing timers
[0179.019] creating bootstrap completion thread
[0179.023] top of bootstrap2()
[0179.026] CPU: ARM Cortex A57
[0179.029] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0179.033] initializing platform
[0179.036] Scratch reg 37 & 271 initial value set..
[0179.143] config for ddr50 mode completed
[0179.146] sdmmc bdev is already initialized
[0179.151] of_register: registering tegra_udc to of_hal
[0179.156] of_register: registering tegra_udc to of_hal
[0179.161] of_register: registering inv20628-driver to of_hal
[0179.166] of_register: registering ads1015-driver to of_hal
[0179.172] of_register: registering lp8557-bl-driver to of_hal
[0179.178] of_register: registering bq2419x_charger to of_hal
[0179.183] of_register: registering cpc to of_hal
[0179.188] of_register: registering bq27441_fuel_gauge to of_hal
[0179.202] gpio framework initialized
[0179.206] of_register: registering tca9539_gpio to of_hal
[0179.211] of_register: registering tca9539_gpio to of_hal
[0179.216] of_register: registering i2c_bus_driver to of_hal
[0179.222] of_register: registering i2c_bus_driver to of_hal
[0179.227] of_register: registering i2c_bus_driver to of_hal
[0179.233] of_register: registering i2c_bus_driver to of_hal
[0179.239] pmic framework initialized
[0179.242] of_register: registering max77620_pmic to of_hal
[0179.248] regulator framework initialized
[0179.251] of_register: registering tps65132_bl_driver to of_hal
[0179.257] initializing target
[0179.264] gpio_driver_register: register 'tegra_gpio_driver' driver
[0179.270] tegra_init_gpio_from_dtb: Error getting prop value for gpio-init-0!
[0179.277] tegra_init_gpio_from_dtb: failed to initialize GPIO tables!
[0179.288] fixed regulator driver initialized
[0179.331] initializing OF layer
[0179.336] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0179.358] I2C Bus Init done
[0179.361] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0179.373] I2C Bus Init done
[0179.375] of_children_init: Ops found for compatible string ti,tca9539
[0179.386] tca9539_init: i2c bus: 2, slave addr: 0xe8
[0179.391] I2C slave not started
[0179.394] I2C write failed
[0179.397] i2c write failed
[0179.399] Slave: 0xe8, Register 0x4 Instance 2, Buffer Size: 0
[0179.405] tca9539_device_init: failed to write polar reg
[0179.410] tca9539_init: failed to init device!
[0179.415] of_children_init: Ops found for compatible string ti,tca9539
[0179.426] tca9539_init: i2c bus: 2, slave addr: 0xee
[0179.431] I2C slave not started
[0179.434] I2C write failed
[0179.436] i2c write failed
[0179.439] Slave: 0xee, Register 0x4 Instance 2, Buffer Size: 0
[0179.445] tca9539_device_init: failed to write polar reg
[0179.450] tca9539_init: failed to init device!
[0179.454] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0179.466] I2C Bus Init done
[0179.469] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0179.480] I2C Bus Init done
[0179.483] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0179.495] I2C Bus Init done
[0179.497] of_children_init: Ops found for compatible string maxim,max77620
[0179.509] max77620_init using irq 118
[0179.514] register 'maxim,max77620' pmic
[0179.518] gpio_driver_register: register 'max77620-gpio' driver
[0179.524] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0179.536] I2C Bus Init done
[0179.540] Applying platform configs
[0179.549] platform-init is not present. Skipping
[0179.554] calling apps_init()
[0179.570] Found 19 GPT partitions in "sdmmc3_user"
[0179.575] Proceeding to flashing Server
[0179.579] usbdcd_reinit Initialize driver to use already enumerated device
[0179.586] nv3p_priv_usbf_open USB configuration success
[0179.869] Writing GPT partition
[0179.873] Erasing Boot device
[0179.876] device_write_gpt: Erasing boot device sdmmc3_boot
[0179.930] Erasing Storage Device
[0181.097] Sanitizing Storage Device
[0181.264] Writing protective mbr
[0181.277] Writing primary GPT
[0181.316] Writing secondary GPT
[0181.339] Found 19 GPT partitions in "sdmmc3_user"
[0181.344] Writing NVC partition
[0181.401] partition NVC write successful.
[0181.406] Writing APP partition
[0209.509] max77620_clear_syswdt clearing watchdog
[0239.509] max77620_clear_syswdt clearing watchdog
[0269.509] max77620_clear_syswdt clearing watchdog
[0299.509] max77620_clear_syswdt clearing watchdog
[0329.509] max77620_clear_syswdt clearing watchdog
[0348.260] partition APP write successful.
[0348.265] Writing TBC partition
[0348.314] partition TBC write successful.
[0348.319] Writing EBT partition
[0348.397] partition EBT write successful.
[0348.403] Writing BPF partition
[0348.429] partition BPF write successful.
[0348.434] Writing WB0 partition
[0348.458] partition WB0 write successful.
[0348.463] Writing RP1 partition
[0348.540] partition RP1 write successful.
[0348.545] Writing TOS partition
[0348.581] partition TOS write successful.
[0348.586] Writing EKS partition
[0348.608] partition EKS write successful.
[0348.613] Writing BMP partition
[0348.644] partition BMP write successful.
[0348.649] Writing LNX partition
[0348.682] partition LNX write successful.
[0348.688] Writing DTB partition
[0348.733] partition DTB write successful.
[0348.869] Writing BCT partition
[0349.285] partition BCT write successful.
[0349.425] Scratch 37 initial value set..
[0349.428] Change state to cold boot mode
[0349.432] Flushing data to stroage
[0000.195] [TegraBoot] (version 00.00.2018.01-l4t-89b97a49)
[0000.200] Processing in cold boot mode Bootloader 2
[0000.205] A02 Bootrom Patch rev = 63
[0000.208] Power-up reason: software reset
[0000.212] No Battery Present
[0000.215] pmic max77620 reset reason
[0000.218] pmic max77620 NVERC : 0x0
[0000.221] RamCode = 0
[0000.224] Platform has Ddr4 type ram
[0000.227] max77620 disabling SD1 Remote Sense
[0000.231] Setting Ddr voltage to 1125mv
[0000.235] Serial Number of Pmic Max77663: 0xb09b5
[0000.243] Entering ramdump check
[0000.246] Get RamDumpCarveOut = 0x0
[0000.249] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0000.254] Last reboot was clean, booting normally!
[0000.259] Sdram initialization is successful 
[0000.263] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.269] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.275] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.281] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.286] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.292] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.298] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.304] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.320] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.326] Platform-DebugCarveout: 0
[0000.329] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.335] Non secure mode, and RB not enabled.
[0000.339] Rail not supported
[0000.364] Csd NumOfBlocks=0
[0000.370] Using GPT Primary to query partitions
[0000.375] Loading Tboot-CPU binary
[0000.424] Verifying TBC in OdmNonSecureSBK mode
[0000.434] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.441] Bootloader downloaded successfully.
[0000.445] Downloaded Tboot-CPU binary to 0xa0000258
[0000.451] MAX77620_GPIO1 Configured.
[0000.454] MAX77620_GPIO5 Configured.
[0000.457] CPU power rail is up
[0000.460] CPU clock enabled
[0000.464] Performing RAM repair
[0000.467] Updating A64 Warmreset Address to 0xa00002e9
[0000.472] Loading NvTbootBootloaderDTB
[0000.499] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0000.640] Bootloader DTB Load Address: 0x83000000
[0000.645] Loading NvTbootKernelDTB
[0000.671] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0000.812] Kernel DTB Load Address: 0x83100000
[0000.817] Loading cboot binary
[0000.911] Verifying EBT in OdmNonSecureSBK mode
[0000.953] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0000.960] Bootloader downloaded successfully.
[0000.965] Next binary entry address: 0x92c00258 
[0000.969] BoardId: 2180
[0000.986] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0001.080] /bpmp deleted
[0001.082] SC7EntryFw header found loaded at 0xff700000
[0001.337] OVR2 PMIC
[0001.339] Bpmp FW successfully loaded
[0001.344] WB0 init successfully at 0xff780000
[0001.348] Set NvDecSticky Bits
[0001.351] GSC2 address ff53fffc value c0edbbcc
[0001.358] GSC MC Settings done
[0001.361] TOS Image length 53680
[0001.364]  Monitor size 53680
[0001.367]  OS size 0
[0001.373] Secure Os AES-CMAC Verification Success!
[0001.378] TOS image cipher info: plaintext
[0001.382] Loading and Validation of Secure OS Successful
[0001.397] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.402] NvTbootPackSdramParams: start. 
[0001.407] NvTbootPackSdramParams: done. 
[0001.411] Tegraboot started after 175263 us
[0001.415] Basic modules init took 822554 us
[0001.419] Sec Bootdevice Read Time = 204 ms, Read Size = 8977 KB
[0001.425] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0001.430] Next stage binary read took 12204 us
[0001.435] Carveout took -14912 us
[0001.438] CPU initialization took 450087 us
[0001.442] Total time taken by TegraBoot 1269933 us

[0001.446] Starting CPU & Halting co-processor 

64NOTICE:  BL31: v1.3(release):a28d87f09
NOTICE:  BL31: Built : 16:52:46, Jul 16 2019
ERROR:   Error initializing runtime service trusty_fast
[0001.570] RamCode = 0
[0001.585] LPDDR4 Training: Read DT: Number of tables = 10
[0001.590] EMC Training (SRC-freq: 204000; DST-freq: 408000)
[0001.596] EMC Training Successful
[0001.599] EMC Training (SRC-freq: 204000; DST-freq: 665600)
[0001.605] EMC Training Successful
[0001.608] EMC Training (SRC-freq: 204000; DST-freq: 800000)
[0001.619] EMC Training Successful
[0001.622] EMC Training (SRC-freq: 204000; DST-freq: 1065600)
[0001.645] EMC Training Successful
[0001.648] EMC Training (SRC-freq: 204000; DST-freq: 1331200)
[0001.670] EMC Training Successful
[0001.673] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0001.693] EMC Training Successful
[0001.696] Switching to 800000 KHz Success
[0001.704] RamCode = 0
[0001.707] DT Write: emc-table@40800 succeeded
[0001.713] DT Write: emc-table@68000 succeeded
[0001.718] DT Write: emc-table@102000 succeeded
[0001.724] DT Write: emc-table@204000 succeeded
[0001.729] DT Write: emc-table@408000 succeeded
[0001.735] DT Write: emc-table@665600 succeeded
[0001.740] DT Write: emc-table@800000 succeeded
[0001.746] DT Write: emc-table@1065600 succeeded
[0001.751] DT Write: emc-table@1331200 succeeded
[0001.757] DT Write: emc-table@1600000 succeeded
[0001.761] LPDDR4 Training: Write DT: Number of tables = 10
[0001.810] 
[0001.811] Debug Init done
[0001.814] Marked DTB cacheable
[0001.817] Bootloader DTB loaded at 0x83000000
[0001.821] Marked DTB cacheable
[0001.824] Kernel DTB loaded at 0x83100000
[0001.828] DeviceTree Init done
[0001.842] Pinmux applied successfully
[0001.847] gicd_base: 0x50041000
[0001.851] gicc_base: 0x50042000
[0001.854] Interrupts Init done
[0001.859] Using base:0x60005090 & irq:208 for tick-timer
[0001.864] Using base:0x60005098 for delay-timer
[0001.868] platform_init_timer: DONE
[0001.872] Timer(tick) Init done
[0001.876] osc freq = 38400 khz
[0001.881] 
[0001.882] welcome to cboot
[0001.884] 
[0001.885] Cboot Version: 00.00.2018.01-t210-29b0d242
[0001.890] calling constructors
[0001.893] initializing heap
[0001.896] initializing threads
[0001.899] initializing timers
[0001.902] creating bootstrap completion thread
[0001.906] top of bootstrap2()
[0001.909] CPU: ARM Cortex A57
[0001.912] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0001.917] initializing platform
[0001.920] Scratch reg 37 & 271 initial value set..
[0001.931] Access to PMC is restricted to TZ
[0001.993] config for ddr50 mode completed
[0001.997] sdmmc bdev is already initialized
[0002.001] Enable APE clock
[0002.004] Un-powergate APE partition
[0002.007] of_register: registering tegra_udc to of_hal
[0002.013] of_register: registering tegra_udc to of_hal
[0002.018] of_register: registering inv20628-driver to of_hal
[0002.023] of_register: registering ads1015-driver to of_hal
[0002.029] of_register: registering lp8557-bl-driver to of_hal
[0002.035] of_register: registering bq2419x_charger to of_hal
[0002.040] of_register: registering cpc to of_hal
[0002.045] of_register: registering bq27441_fuel_gauge to of_hal
[0002.059] gpio framework initialized
[0002.062] of_register: registering tca9539_gpio to of_hal
[0002.068] of_register: registering tca9539_gpio to of_hal
[0002.073] of_register: registering i2c_bus_driver to of_hal
[0002.079] of_register: registering i2c_bus_driver to of_hal
[0002.084] of_register: registering i2c_bus_driver to of_hal
[0002.090] of_register: registering i2c_bus_driver to of_hal
[0002.095] pmic framework initialized
[0002.099] of_register: registering max77620_pmic to of_hal
[0002.104] regulator framework initialized
[0002.108] of_register: registering tps65132_bl_driver to of_hal
[0002.114] initializing target
[0002.120] gpio_driver_register: register 'tegra_gpio_driver' driver
[0002.127] tegra_init_gpio_from_dtb: Error getting prop value for gpio-init-0!
[0002.134] tegra_init_gpio_from_dtb: failed to initialize GPIO tables!
[0002.144] fixed regulator driver initialized
[0002.187] initializing OF layer
[0002.190] NCK carveout not present
[0002.194] Skipping dts_overrides
[0002.198] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.220] I2C Bus Init done
[0002.223] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.234] I2C Bus Init done
[0002.237] of_children_init: Ops found for compatible string ti,tca9539
[0002.248] tca9539_init: i2c bus: 2, slave addr: 0xe8
[0002.252] I2C slave not started
[0002.255] I2C write failed
[0002.258] i2c write failed
[0002.261] Slave: 0xe8, Register 0x4 Instance 2, Buffer Size: 0
[0002.266] tca9539_device_init: failed to write polar reg
[0002.272] tca9539_init: failed to init device!
[0002.276] of_children_init: Ops found for compatible string ti,tca9539
[0002.287] tca9539_init: i2c bus: 2, slave addr: 0xee
[0002.292] I2C slave not started
[0002.295] I2C write failed
[0002.298] i2c write failed
[0002.300] Slave: 0xee, Register 0x4 Instance 2, Buffer Size: 0
[0002.306] tca9539_device_init: failed to write polar reg
[0002.311] tca9539_init: failed to init device!
[0002.316] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.327] I2C Bus Init done
[0002.330] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.342] I2C Bus Init done
[0002.344] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.356] I2C Bus Init done
[0002.359] of_children_init: Ops found for compatible string maxim,max77620
[0002.370] max77620_init using irq 118
[0002.375] register 'maxim,max77620' pmic
[0002.379] gpio_driver_register: register 'max77620-gpio' driver
[0002.385] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.397] I2C Bus Init done
[0002.401] NCK carveout not present
[0002.405] shim_invoke: No NCT, Calling dts updates
[0002.419] Find /i2c@7000c000's alias i2c0
[0002.423] get eeprom at 1-a2, size 256, type 0
[0002.428] get eeprom at 1-ae, size 256, type 0
[0002.439] Find /i2c@7000c400's alias i2c1
[0002.442] get eeprom at 2-a0, size 256, type 0
[0002.454] Find /i2c@7000c500's alias i2c2
[0002.457] get eeprom at 3-a0, size 256, type 0
[0002.462] get eeprom at 3-ae, size 256, type 0
[0002.471] Find /host1x/i2c@546c0000's alias i2c6
[0002.475] get eeprom at 7-a8, size 256, type 0
[0002.480] pm_ids_update: Updating 1,a2, size 256, type 0
[0002.485] I2C slave not started
[0002.488] I2C write failed
[0002.491] Writing offset failed
[0002.494] eeprom_init: EEPROM read failed
[0002.498] pm_ids_update: eeprom init failed
[0002.502] pm_ids_update: Updating 1,ae, size 256, type 0
[0002.507] I2C slave not started
[0002.510] I2C write failed
[0002.513] Writing offset failed
[0002.516] eeprom_init: EEPROM read failed
[0002.520] pm_ids_update: eeprom init failed
[0002.524] pm_ids_update: Updating 2,a0, size 256, type 0
[0002.529] I2C slave not started
[0002.532] I2C write failed
[0002.535] Writing offset failed
[0002.538] eeprom_init: EEPROM read failed
[0002.542] pm_ids_update: eeprom init failed
[0002.546] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.576] pm_ids_update: The pm board id is 2180-1000-400
[0002.583] Adding plugin-manager/ids/2180-1000-400=/i2c@7000c500:module@0x50
[0002.591] pm_ids_update: pm id update successful
[0002.596] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.601] I2C slave not started
[0002.604] I2C write failed
[0002.607] Writing offset failed
[0002.610] eeprom_init: EEPROM read failed
[0002.614] pm_ids_update: eeprom init failed
[0002.618] pm_ids_update: Updating 7,a8, size 256, type 0
[0002.624] GPIO driver for phandle 0xf1 could not be found
[0002.630] I2C slave not started
[0002.633] I2C write failed
[0002.635] Writing offset failed
[0002.638] eeprom_init: EEPROM read failed
[0002.642] pm_ids_update: eeprom init failed
[0002.647] GPIO driver for phandle 0xf1 could not be found
[0002.680] updating /chosen/nvidia,wifi-mac node 00:04:4b:66:59:ff
[0002.688] updating /chosen/nvidia,bluetooth-mac node 00:04:4b:66:5a:00
[0002.696] updating /chosen/nvidia,ethernet-mac node 00:04:4b:66:5a:01
[0002.702] Plugin Manager: Parse ODM data 0x00094000
[0002.715] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1   
[0002.742] Find /i2c@7000c000's alias i2c0
[0002.746] get eeprom at 1-a2, size 256, type 0
[0002.751] get eeprom at 1-ae, size 256, type 0
[0002.762] Find /i2c@7000c400's alias i2c1
[0002.766] get eeprom at 2-a0, size 256, type 0
[0002.777] Find /i2c@7000c500's alias i2c2
[0002.781] get eeprom at 3-a0, size 256, type 0
[0002.785] get eeprom at 3-ae, size 256, type 0
[0002.794] Find /host1x/i2c@546c0000's alias i2c6
[0002.798] get eeprom at 7-a8, size 256, type 0
[0002.803] pm_ids_update: Updating 1,a2, size 256, type 0
[0002.808] I2C slave not started
[0002.811] I2C write failed
[0002.814] Writing offset failed
[0002.817] eeprom_init: EEPROM read failed
[0002.821] pm_ids_update: eeprom init failed
[0002.825] pm_ids_update: Updating 1,ae, size 256, type 0
[0002.830] I2C slave not started
[0002.833] I2C write failed
[0002.836] Writing offset failed
[0002.839] eeprom_init: EEPROM read failed
[0002.843] pm_ids_update: eeprom init failed
[0002.847] pm_ids_update: Updating 2,a0, size 256, type 0
[0002.852] I2C slave not started
[0002.855] I2C write failed
[0002.858] Writing offset failed
[0002.861] eeprom_init: EEPROM read failed
[0002.865] pm_ids_update: eeprom init failed
[0002.869] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.899] pm_ids_update: The pm board id is 2180-1000-400
[0002.906] Adding plugin-manager/ids/2180-1000-400=/i2c@7000c500:module@0x50
[0002.913] pm_ids_update: pm id update successful
[0002.917] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.923] I2C slave not started
[0002.926] I2C write failed
[0002.928] Writing offset failed
[0002.931] eeprom_init: EEPROM read failed
[0002.935] pm_ids_update: eeprom init failed
[0002.940] pm_ids_update: Updating 7,a8, size 256, type 0
[0002.946] GPIO driver for phandle 0xf1 could not be found
[0002.951] I2C slave not started
[0002.954] I2C write failed
[0002.957] Writing offset failed
[0002.960] eeprom_init: EEPROM read failed
[0002.964] pm_ids_update: eeprom init failed
[0002.969] GPIO driver for phandle 0xf1 could not be found
[0003.001] Chip UID is 00000001642897c0040000000c0200c0
[0003.006] Add serial number:03236161235820c00002 as DT property
[0003.016] Applying platform configs
[0003.025] platform-init is not present. Skipping
[0003.029] calling apps_init()
[0003.045] Found 19 GPT partitions in "sdmmc3_user"
[0003.049] Proceeding to Cold Boot
[0003.053] starting app android_boot_app
[0003.056] Device state: unlocked
[0003.060] display console init
[0003.066] status of dsi node is not okay
[0003.074] enabling 'vdd-hdmi' regulator
[0003.077] GPIO driver for phandle 0xf2 could not be found
[0003.083] hdmi cable connected
[0003.098] edid read success
[0003.107] DT entry for leds-pwm not found
[0003.119] edid read success
[0003.122] width = 640, height = 480, frequency = 25174825
[0003.127] width = 640, height = 480, frequency = 25174825
[0003.133] width = 640, height = 480, frequency = 25174825
[0003.138] width = 640, height = 480, frequency = 25174825
[0003.143] width = 1280, height = 800, frequency = 83500000
[0003.149] width = 720, height = 576, frequency = 27000000
[0003.154] width = 720, height = 480, frequency = 26973026
[0003.160] width = 720, height = 480, frequency = 26973026
[0003.165] width = 720, height = 576, frequency = 26973026
[0003.170] width = 720, height = 576, frequency = 26973026
[0003.176] width = 1280, height = 720, frequency = 74175824
[0003.181] width = 1280, height = 720, frequency = 74175824
[0003.187] width = 1920, height = 1080, frequency = 148351648
[0003.192] width = 1920, height = 1080, frequency = 148351648
[0003.198] Best mode Width = 1920, Height = 1080, freq = 148351648
[0003.206] tmds-config node not found
[0003.210] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'vdd-hdmi-dp' regulator to 1050000 micro volts
[0003.225] setting 'vdd-1v8' regulator to 1800000 micro volts
[0003.232] enabling 'vdd-hdmi' regulator
[0003.236] GPIO driver for phandle 0xf2 could not be found
[0003.267] using default cmu settings
[0003.270] dc_hdmi_enable, starting HDMI initialisation
[0003.276] dc_hdmi_enable, HDMI initialisation complete
[0003.281] list and configure display window
[0003.290] display console init completed
[0003.303] Gpio keyboard init success
[0003.324] found decompressor handler: lz4-legacy
[0003.338] decompressing blob (type 1)...
[0003.362] load_bmp_blob: panelresolution=1080 type=3
[0003.368] Could not load/initialize FW partition... ignoring
[0003.374] se_aes_verify_sbk_clear: Error
[0003.378] bl_battery_charging: connected to external power supply
[0003.387] device_query_partition_size: failed to open partition sdmmc3_user:MSC !
[0003.395] MSC Partition not found
[0003.404] blob_init: USP partition does not have valid Blob
[0003.410] kfs_getpartname: name = LNX
[0003.413] Loading kernel from LNX
[0003.433] Verifying boot image in OdmNonSecureSBK mode
[0003.454] kernel load address: 0x80080000, size: 495205 bytes
[0003.460] ramdisk load address: 0x84100000, size: 0 bytes
[0003.465] load kernel from storage
[0003.475] decompressor handler not found
[0003.495] Successfully loaded kernel and ramdisk images
[0003.501] load_bmp_blob: panelresolution=1080 type=3
[0003.685] display bmp image done
[0003.688] NCK carveout not present
[0003.691] Skipping dts_overrides
[0003.694] NCK carveout not present
[0003.698] shim_invoke: No NCT, Calling dts updates
[0003.712] Find /i2c@7000c000's alias i2c0
[0003.716] get eeprom at 1-a2, size 256, type 0
[0003.721] get eeprom at 1-ae, size 256, type 0
[0003.732] Find /i2c@7000c400's alias i2c1
[0003.736] get eeprom at 2-a0, size 256, type 0
[0003.747] Find /i2c@7000c500's alias i2c2
[0003.751] get eeprom at 3-a0, size 256, type 0
[0003.755] get eeprom at 3-ae, size 256, type 0
[0003.764] Find /host1x/i2c@546c0000's alias i2c6
[0003.768] get eeprom at 7-a8, size 256, type 0
[0003.773] pm_ids_update: Updating 1,a2, size 256, type 0
[0003.778] I2C slave not started
[0003.781] I2C write failed
[0003.784] Writing offset failed
[0003.787] eeprom_init: EEPROM read failed
[0003.791] pm_ids_update: eeprom init failed
[0003.795] pm_ids_update: Updating 1,ae, size 256, type 0
[0003.800] I2C slave not started
[0003.803] I2C write failed
[0003.806] Writing offset failed
[0003.809] eeprom_init: EEPROM read failed
[0003.813] pm_ids_update: eeprom init failed
[0003.817] pm_ids_update: Updating 2,a0, size 256, type 0
[0003.822] I2C slave not started
[0003.825] I2C write failed
[0003.828] Writing offset failed
[0003.831] eeprom_init: EEPROM read failed
[0003.835] pm_ids_update: eeprom init failed
[0003.839] pm_ids_update: Updating 3,a0, size 256, type 0
[0003.869] pm_ids_update: The pm board id is 2180-1000-400
[0003.876] Adding plugin-manager/ids/2180-1000-400=/i2c@7000c500:module@0x50
[0003.884] pm_ids_update: pm id update successful
[0003.889] pm_ids_update: Updating 3,ae, size 256, type 0
[0003.894] I2C slave not started
[0003.897] I2C write failed
[0003.900] Writing offset failed
[0003.903] eeprom_init: EEPROM read failed
[0003.907] pm_ids_update: eeprom init failed
[0003.911] pm_ids_update: Updating 7,a8, size 256, type 0
[0003.917] GPIO driver for phandle 0xf1 could not be found
[0003.923] I2C slave not started
[0003.926] I2C write failed
[0003.928] Writing offset failed
[0003.931] eeprom_init: EEPROM read failed
[0003.935] pm_ids_update: eeprom init failed
[0003.941] GPIO driver for phandle 0xf1 could not be found
[0003.973] updating /chosen/nvidia,wifi-mac node 00:04:4b:66:59:ff
[0003.981] updating /chosen/nvidia,bluetooth-mac node 00:04:4b:66:5a:00
[0003.989] updating /chosen/nvidia,ethernet-mac node 00:04:4b:66:5a:01
[0003.996] Plugin Manager: Parse ODM data 0x00094000
[0004.008] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1   
[0004.026] Add serial number:03236161235820c00002 as DT property
[0004.038] "bpmp" doesn't exist, creating 
[0004.045] Updated bpmp info to DTB
[0004.051] Updated initrd info to DTB
[0004.054] "proc-board" doesn't exist, creating 
[0004.060] Updated board info to DTB
[0004.063] "pmu-board" doesn't exist, creating 
[0004.069] Updated board info to DTB
[0004.073] "display-board" doesn't exist, creating 
[0004.079] Updated board info to DTB
[0004.082] "reset" doesn't exist, creating 
[0004.087] Updated reset info to DTB
[0004.090] Cmdline: tegraid=21.1.2.0.0 ddr_die=2048M@2048M ddr_die=2048M@4096M section=256M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 tegra_fbmem2=0x800000@0x92cb4000 is_hdmi_initialised=1 
[0004.131] DTB cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1   
[0004.146] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 
[0004.163] Updated bootarg info to DTB
[0004.166] Adding uuid 00000001642897c0040000000c0200c0 to DT
[0004.172] Adding eks info 0 to DT
[0004.179] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7
[0004.185] Updated memory info to DTB
[0004.195] set vdd_core voltage to 1075 mv
[0004.199] setting 'vdd-core' regulator to 1075000 micro volts
[0004.205] Found secure-pmc; disable BPMP


U-Boot 2016.07-gd917e08cec (Jul 16 2019 - 16:52:58 -0700)

TEGRA210
Model: NVIDIA P2371-2180
Board: NVIDIA P2371-2180
DRAM:  4 GiB
MC:   Tegra SD/MMC: 0, Tegra SD/MMC: 1
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0 
MMC: no card present
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
728 bytes read in 93 ms (6.8 KiB/s)
L4T boot options
1:	primary kernel
Enter choice: 1:	primary kernel
Retrieving file: /boot/initrd
5562393 bytes read in 192 ms (27.6 MiB/s)
Retrieving file: /boot/Image
34179080 bytes read in 810 ms (40.2 MiB/s)
append: tegraid=21.1.2.0.0 ddr_die=2048M@2048M ddr_die=2048M@4096M section=256M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 tegra_fbmem2=0x800000@0x92cb4000 is_hdmi_initialised=1  root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1    root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 
## Flattened Device Tree blob at 83100000
   Booting using the fdt blob at 0x83100000
   reserving fdt memory region: addr=80000000 size=20000
   Using Device Tree in place at 0000000083100000, end 00000000831ba2e7

Starting kernel ...

<hit enter to activate fiq debugger>
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.140-tegra (buildbrain@mobile-u64-911) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Tue Jul 16 17:04:49 PDT 2019
[    0.000000] Boot CPU: AArch64 Processor [411fd071]
[    0.000000] OF: fdt:memory scan node memory@80000000, reg size 48,
[    0.000000] OF: fdt: - 80000000 ,  7ee00000
[    0.000000] OF: fdt: - 100000000 ,  7f200000
[    0.000000] Found tegra_fbmem2: 00800000@92cb4000
[    0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB
[    0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB
[    0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB
[    0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB
[    0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout
[    0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops
[    0.000000] cma: Reserved 64 MiB at 0x00000000fac00000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.1
[    0.000000] percpu: Embedded 25 pages/cpu @ffffffc0fefcc000 s61592 r8192 d32616 u102400
[    0.000000] CPU features: enabling workaround for ARM erratum 832075
[    0.000000] Speculative Store Bypass Disable mitigation not required
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 1023544
[    0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=2048M@2048M ddr_die=2048M@4096M section=256M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 tegra_fbmem2=0x800000@0x92cb4000 is_hdmi_initialised=1  root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1    root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 
[    0.000000] log_buf_len individual max cpu contribution: 32768 bytes
[    0.000000] log_buf_len total cpu_extra contributions: 98304 bytes
[    0.000000] log_buf_len min size: 32768 bytes
[    0.000000] log_buf_len: 131072 bytes
[    0.000000] early log buf free: 29404(89%)
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] Memory: 3971600K/4159488K available (15230K kernel code, 2914K rwdata, 6628K rodata, 8576K init, 609K bss, 122352K reserved, 65536K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000   (   250 GB)
[    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008f60000   ( 15232 KB)
[    0.000000]     .rodata : 0xffffff8008f60000 - 0xffffff80095e0000   (  6656 KB)
[    0.000000]       .init : 0xffffff80095e0000 - 0xffffff8009e40000   (  8576 KB)
[    0.000000]       .data : 0xffffff8009e40000 - 0xffffff800a118808   (  2915 KB)
[    0.000000]        .bss : 0xffffff800a118808 - 0xffffff800a1b0dbc   (   610 KB)
[    0.000000]     fixed   : 0xffffffbefe7fd000 - 0xffffffbefec00000   (  4108 KB)
[    0.000000]     PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000   (    16 MB)
[    0.000000]     vmemmap : 0xffffffbf00000000 - 0xffffffc000000000   (     4 GB maximum)
[    0.000000]               0xffffffbf00000000 - 0xffffffbf03fc8000   (    63 MB actual)
[    0.000000]     memory  : 0xffffffc000000000 - 0xffffffc0ff200000   (  4082 MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Build-time adjustment of leaf fanout to 64.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller
[    0.000000] t210 clock and reset probe
[    0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1
[    0.000000] clk_cbus_recalc_rate: no gbus parent
[    0.000000] clk_cbus_recalc_rate: no gbus parent
[    0.000000] clk_cbus_recalc_rate: no gbus parent
[    0.000000] clk_cbus_recalc_rate: no gbus parent
[    0.000000] clk_cbus_recalc_rate: no gbus parent
[    0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.002223] Console: colour dummy device 80x25
[    0.003067] console [tty0] enabled
[    0.003086] kmemleak: Kernel memory leak detector disabled
[    0.003109] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800)
[    0.003137] pid_max: default: 32768 minimum: 301
[    0.003551] Security Framework initialized
[    0.003769] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.003788] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.004594] ftrace: allocating 46935 entries in 184 pages
[    0.161382] ASID allocator initialised with 65536 entries
[    0.198882] tegra-id: chipid=22117.
[    0.198909] tegra-id: opt_subrevision=0.
[    0.198934] Tegra Speedo/IDDQ fuse revision 4
[    0.198949] Tegra: CPU Speedo ID 7, SoC Speedo ID 0, GPU Speedo ID 2
[    0.198965] Tegra: CPU Process ID 0, SoC Process ID 1, GPU Process ID 0
[    0.198982] Tegra: CPU Speedo Value 2085, SoC Speedo Value 1965, GPU Speedo Value 2080
[    0.199003] Tegra: CPU IDDQ Value 2288, SoC IDDQ Value 2420, GPU IDDQ Value 3115
[    0.199034] Tegra Revision: A02 SKU: 0x17 CPU Process: 0 SoC Process: 1
[    0.199054] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/jetson/kernel-dts/tegra210-jetson-tx1-p2597-2180-a01-devkit.dts
[    0.199088] DTB Build time: Jul 16 2019 17:09:33
[    0.248640] CPU1: Booted secondary processor [411fd071]
[    0.280618] CPU2: Booted secondary processor [411fd071]
[    0.312605] CPU3: Booted secondary processor [411fd071]
[    0.312674] Brought up 4 CPUs
[    0.312728] SMP: Total of 4 processors activated.
[    0.312744] CPU features: detected feature: 32-bit EL0 Support
[    0.312982] CPU: All CPU(s) started at EL2
[    0.313009] alternatives: patching kernel code
[    0.318210] devtmpfs: initialized
[    0.370655] Initilizing CustomIPI irq domain
[    0.370904] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.370940] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.371999] pinctrl core: initialized pinctrl subsystem
[    0.372275] OS set in device tree is not L4T.
[    0.372501] regulator-dummy: no parameters
[    0.372704] Initializing plugin-manager
[    0.372785] Plugin module not found
[    0.374023] node /plugin-manager/fragement@0 match with board >=2180-1000-300
[    0.375139] node /plugin-manager/fragement@5 match with odm-data enable-tegra-wdt
[    0.375606] node /plugin-manager/fragement@7 match with odm-data enable-tegra-wdt
[    0.377941] NET: Registered protocol family 16
[    0.380432] pstore: using zlib compression
[    0.380955] console [pstore-1] enabled
[    0.380970] pstore: Registered ramoops as persistent store backend
[    0.380987] ramoops: attached 0x200000@0xb0000000, ecc: 0/0
[    0.400193] cpuidle: using governor menu
[    0.404165] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver
[    0.406041] vdso: 2 pages (1 code @ ffffff8008f67000, 1 data @ ffffff8009e44000)
[    0.406075] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.408256] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations
[    0.411252] tegra_powergate_init: DONE
[    0.411281] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/jetson/kernel-dts/tegra210-jetson-tx1-p2597-2180-a01-devkit.dts
[    0.411316] DTB Build time: Jul 16 2019 17:09:33
[    0.413363] Tegra reboot handler registered.
[    0.417232] iommu: Adding device tegra-carveouts to group 0
[    0.417315] platform tegra-carveouts: domain=ffffffc0f9542f18 allocates as[0]=ffffffc0f955c0a8
[    0.417589] iommu: Adding device smmu_test to group 1
[    0.417647] platform smmu_test: domain=ffffffc0f954e198 allocates as[0]=ffffffc0f955c110
[    0.418341] mc: mapped MMIO address: 0xffffff800802e000 -> 0x70019000
[    0.418413] mc: mapped MMIO address: 0xffffff8008065000 -> 0x7001c000
[    0.418482] mc: mapped MMIO address: 0xffffff8008079000 -> 0x7001d000
[    0.418503] nv-tegra-mc 70019000.mc: No mssnvlink node
[    0.418526] mc-err: mcerr ops are set to t21x
[    0.427677] iommu: Adding device 70090000.xusb to group 2
[    0.427942] iommu: Adding device 70006000.serial to group 3
[    0.427996] platform 70006000.serial: domain=ffffffc0f96309d8 allocates as[0]=ffffffc0f955c178
[    0.428364] iommu: Adding device 70006040.serial to group 4
[    0.428622] iommu: Adding device 70006200.serial to group 5
[    0.428878] iommu: Adding device 70006300.serial to group 6
[    0.429078] iommu: Adding device sound to group 7
[    0.429129] platform sound: domain=ffffffc0f963c0d8 allocates as[0]=ffffffc0f955c1e0
[    0.429593] iommu: Adding device 7000d400.spi to group 8
[    0.429871] iommu: Adding device 7000da00.spi to group 9
[    0.430183] iommu: Adding device 50000000.host1x to group 10
[    0.430457] iommu: Adding device 54080000.vi to group 11
[    0.430840] iommu: Adding device 54600000.isp to group 12
[    0.431105] iommu: Adding device 54680000.isp to group 13
[    0.431382] iommu: Adding device tegradc.1 to group 14
[    0.431435] platform tegradc.1: domain=ffffffc0f963ce58 allocates as[0]=ffffffc0f955c248
[    0.434917] platform tegradc.1: IOVA linear map 0x0000000092cb4000(800000)
[    0.435154] iommu: Adding device 54340000.vic to group 15
[    0.435359] iommu: Adding device 544c0000.nvenc to group 16
[    0.435570] iommu: Adding device 54500000.tsec to group 17
[    0.435766] iommu: Adding device 54100000.tsecb to group 18
[    0.435961] iommu: Adding device 54480000.nvdec to group 19
[    0.436156] iommu: Adding device 54380000.nvjpg to group 20
[    0.436857] iommu: Adding device 546c0000.i2c to group 21
[    0.437179] iommu: Adding device 57000000.gpu to group 22
[    0.437231] platform 57000000.gpu: domain=ffffffc0f9681cd8 allocates as[0]=ffffffc0f955c2b0
[    0.437279] platform 57000000.gpu: domain=ffffffc0f9681cd8 allocates as[1]=ffffffc0f955c318
[    0.437339] platform 57000000.gpu: domain=ffffffc0f9681cd8 allocates as[2]=ffffffc0f955c380
[    0.437387] platform 57000000.gpu: domain=ffffffc0f9681cd8 allocates as[3]=ffffffc0f955c3e8
[    0.438016] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled.
[    0.438050] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present
[    0.438073] tegra-pmc: ### PMC reset source: TEGRA_SOFTWARE_RESET
[    0.438092] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM
[    0.438107] tegra-pmc: ### PMC reset status reg: 0x3
[    0.492302] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered
[    0.492330] tegra-pmc: Clear bootloader IO dpd settings
[    0.492362] tegra-pmc 7000e400.pmc: IO padctrl driver initialized
[    0.492426] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands
[    0.492693] iommu: Adding device 70012000.se to group 23
[    0.493229] iommu: Adding device 1003000.pcie to group 24
[    0.493293] platform 1003000.pcie: domain=ffffffc0f968e498 allocates as[0]=ffffffc0f955c450
[    0.493654] iommu: Adding device 7000c000.i2c to group 25
[    0.493910] iommu: Adding device 7000c400.i2c to group 26
[    0.494166] iommu: Adding device 7000c500.i2c to group 27
[    0.494420] iommu: Adding device 7000c700.i2c to group 28
[    0.494682] iommu: Adding device 7000d000.i2c to group 29
[    0.494933] iommu: Adding device 7000d100.i2c to group 30
[    0.495194] iommu: Adding device sdhci-tegra.3 to group 31
[    0.495246] platform sdhci-tegra.3: domain=ffffffc0f970e018 allocates as[0]=ffffffc0f955c4b8
[    0.495789] iommu: Adding device sdhci-tegra.0 to group 32
[    0.495845] platform sdhci-tegra.0: domain=ffffffc0f970e318 allocates as[0]=ffffffc0f955c520
[    0.496570] iommu: Adding device 700d0000.xudc to group 33
[    0.499104] iommu: Adding device 70027000.sata to group 34
[    0.501439] vdd-ac-bat: 5000 mV 
[    0.502473] vdd-cpu-fixed: 1000 mV 
[    0.533090] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.534927] GPIO line 58 (wlan-default-input) hogged as input
[    0.534966] GPIO line 65 (wlan-default-input) hogged as input
[    0.535001] GPIO line 56 (wlan-default-output-high) hogged as output/high
[    0.535031] GPIO line 64 (wlan-default-output-high) hogged as output/high
[    0.535060] GPIO line 66 (wlan-default-output-high) hogged as output/high
[    0.535093] GPIO line 148 (camera-control-output-low) hogged as output/low
[    0.535122] GPIO line 151 (camera-control-output-low) hogged as output/low
[    0.535151] GPIO line 149 (camera-control-output-low) hogged as output/low
[    0.535179] GPIO line 152 (camera-control-output-low) hogged as output/low
[    0.535422] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio)
[    0.542418] eventlib_kernel: keventlib is initialized, test id: 0
[    0.542687] SCSI subsystem initialized
[    0.543129] usbcore: registered new interface driver usbfs
[    0.543196] usbcore: registered new interface driver hub
[    0.543275] usbcore: registered new device driver usb
[    0.545173] tegra-i2c 7000c400.i2c: no acknowledge from address 0x74
[    0.545229] pca953x 1-0074: failed reading register
[    0.545294] pca953x: probe of 1-0074 failed with error -121
[    0.545641] tegra-i2c 7000c400.i2c: no acknowledge from address 0x77
[    0.545690] pca953x 1-0077: failed reading register
[    0.545740] pca953x: probe of 1-0077 failed with error -121
[    0.547362] max77620 4-003c: PMIC Version OTP:0x3C and ES:0x8
[    0.552718] vdd-core: 600 <--> 1400 mV at 1075 mV 
[    0.553011] random: fast init done
[    0.556789] vddio-ddr: at 1125 mV 
[    0.557381] vdd-pre-reg: 1350 mV 
[    0.560628] vdd-1v8: 1800 mV 
[    0.564695] avdd-sys: 1200 mV 
[    0.568621] vdd-pex: 1050 mV 
[    0.569050] vddio-sdmmc1: 1800 <--> 3300 mV at 3300 mV 
[    0.569561] vdd-cam-hv: Bringing 3100000uV into 2800000-2800000uV
[    0.569649] vdd-cam-hv: 2800 mV 
[    0.570154] vdd-rtc: Bringing 1000000uV into 850000-850000uV
[    0.572623] vdd-rtc: 850 mV 
[    0.573138] avdd-ts-hv: Bringing 3100000uV into 3300000-3300000uV
[    0.573221] avdd-ts-hv: 3300 mV 
[    0.573743] vdd-ts: Bringing 2800000uV into 1800000-1800000uV
[    0.573834] vdd-ts: 1800 mV 
[    0.576626] vdd-gen-pll-edp: 1050 mV 
[    0.580622] vdd-hdmi-dp: 1050 mV 
[    0.581601] GPIO line 506 (spmic-default-output-high) hogged as output/high
[    0.581814] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio)
[    0.583058] max77620 4-003c: max77620 probe successful
[    0.585087] media: Linux media interface: v0.10
[    0.585145] Linux video capture interface: v2.00
[    0.585918] pps_core: LinuxPPS API ver. 1 registered
[    0.585938] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.585974] PTP clock support registered
[    0.588973] tegra_fiq_debugger_init: found FIQ source (IRQ 98)
[    0.597359] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table
[    0.597967] Advanced Linux Sound Architecture Driver Initialized.
[    0.598433] Bluetooth: Core ver 2.22
[    0.598481] NET: Registered protocol family 31
[    0.598498] Bluetooth: HCI device and connection manager initialized
[    0.598520] Bluetooth: HCI socket layer initialized
[    0.598539] Bluetooth: L2CAP socket layer initialized
[    0.598569] Bluetooth: SCO socket layer initialized
[    0.599803] tegra210_dvfs: no clock found for sdmmc2_ddr
[    0.599833] tegra210_dvfs: no clock found for sdmmc4_ddr
[    0.599882] tegra210_dvfs: no clock found for sdmmc1_ddr
[    0.599908] tegra210_dvfs: no clock found for sdmmc3_ddr
[    0.602728] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe
[    0.604631] vdd-3v3: 3300 mV 
[    0.605654] max77620-gpio7: supplied by vdd-gen-pll-edp
[    0.608642] max77620-gpio7: 1050 mV 
[    0.609020] lcd-bl-en: 1800 mV 
[    0.609460] en-vdd-sd: supplied by vdd-3v3
[    0.609501] en-vdd-sd: 3300 mV 
[    0.612644] vdd-sys-boost: 5000 mV 
[    0.613054] aux-3v3: 3300 mV 
[    0.613365] snsr_pm: 3300 mV 
[    0.616642] vdd-disp-3v0: 3000 mV 
[    0.617157] usb-vbus1: supplied by vdd-3v3
[    0.617196] usb-vbus1: 5000 mV 
[    0.618029] rtl-5v0: 5000 mV 
[    0.618403] en-usb-vbus2: 5000 mV 
[    0.618910] en-vdd-vcm-2v8: supplied by vdd-3v3
[    0.618960] en-vdd-vcm-2v8: 2800 mV 
[    0.620145] camchar: rtcpu character device driver loaded
[    0.621822] extcon-gpio-states extcon:extcon@1: Cable state:1, cable id:1
[    0.623081] clocksource: Switched to clocksource arch_sys_counter
[    0.653581] VFS: Disk quotas dquot_6.6.0
[    0.653696] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.654028] nvmap_heap_init: nvmap_heap_init: created heap block cache
[    0.654264] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways
[    0.654290] nvmap_page_pool_init: Total RAM pages: 1009284
[    0.654308] nvmap_page_pool_init: nvmap page pool size: 126160 pages (492 MB)
[    0.654398] nvmap_background_zero_thread: PP zeroing thread starting.
[    0.654560] misc nvmap: iram :dma coherent mem declare 0x0000000040001000,258048
[    0.654685] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB)
[    0.661511] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm
[    0.663111] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm
[    0.663437] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm
[    0.663584] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm
[    0.664767] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type Tdiode_tegra
[    0.664964] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type PMIC-Die
[    0.665181] thermal thermal_zone6: Registering thermal zone thermal_zone6 for type Tboard_tegra
[    0.665364] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz
[    0.665382] pre_t19x_iso_plat_init(): max_iso_bw=33280000KB
[    0.665779] NET: Registered protocol family 2
[    0.666594] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.666825] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.667256] TCP: Hash tables configured (established 32768 bind 32768)
[    0.667340] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.667433] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.667788] NET: Registered protocol family 1
[    0.668282] RPC: Registered named UNIX socket transport module.
[    0.668303] RPC: Registered udp transport module.
[    0.668318] RPC: Registered tcp transport module.
[    0.668333] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.668497] Trying to unpack rootfs image as initramfs...
[    0.886862] Freeing initrd memory: 5432K
[    0.894991] host1x 50000000.host1x: initialized
[    0.896512] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    0.899100] audit: initializing netlink subsys (disabled)
[    0.899153] audit: type=2000 audit(0.759:1): initialized
[    0.899704] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[    0.908439] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.909754] ntfs: driver 2.1.32 [Flags: R/W].
[    0.910442] 9p: Installing v9fs 9p2000 file system support
[    0.913296] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240)
[    0.913412] io scheduler noop registered
[    0.913691] io scheduler cfq registered (default)
[    0.915646] gic 702f9000.agic: GIC IRQ controller registered
[    0.918372] iommu: Adding device 702ef000.adsp to group 35
[    0.924287] iommu: Adding device aconnect@702c0000:adsp_audio to group 36
[    0.924429] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered
[    0.924882] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x9208410
[    0.924911] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4
[    0.926132] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb
[    0.926242] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb
[    0.926346] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb
[    0.926513] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-hsic.3, lane = hsic-0, function = xusb
[    0.926676] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-0, function = pcie-x1
[    0.926779] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-1, function = pcie-x4
[    0.926877] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-2, function = pcie-x4
[    0.926978] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-3, function = pcie-x4
[    0.927252] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-4, function = pcie-x4
[    0.927368] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-5, function = xusb
[    0.927466] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.10, lane = pcie-6, function = xusb
[    0.927633] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-sata.11, lane = sata-0, function = sata
[    0.932737] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops
[    0.934077] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000
[    0.935675] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration
[    0.937337] tegra-pcie 1003000.pcie: PCIE: Enable power rails
[    0.937624] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes
[    0.938507] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe
[    0.938674] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1020000, vi_iso_bw=750000, max_bw=1020000
[    0.938925] Adding domain tsec-pd to PM domain host1x-pd
[    0.940938] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes
[    0.941543] tsec 54500000.tsec: initialized
[    0.942646] tsec 54100000.tsecb: initialized
[    0.943490] Adding domain nvdec-pd to PM domain host1x-pd
[    0.946508] nvdec 54480000.nvdec: initialized
[    0.947647] Adding domain vic03-pd to PM domain host1x-pd
[    0.947844] Adding domain msenc-pd to PM domain host1x-pd
[    0.948020] Adding domain nvjpg-pd to PM domain host1x-pd
[    0.952678] falcon 54340000.vic: initialized
[    0.953809] falcon 544c0000.nvenc: initialized
[    0.955048] falcon 54380000.nvjpg: initialized
[    0.959566] tegradc tegradc.1: disp0 connected to head1->/host1x/sor1
[    0.959668] display board info: id 0xffff, fab 0x0
[    0.959740] generic_infoframe_type: 0x87
[    0.959874] tegradc tegradc.1: DT parsed successfully
[    0.959918] tegradc tegradc.1: Display dc.ffffff800ab40000 registered with id=0
[    0.960257] tegradc tegradc.1: dc_hdmi_hotplug_init: couldn't get regulator vdd_hdmi_5v0, -517
[    0.960364] tegradc tegradc.1: Bootloader disp_param detected. Detected mode: 1920x1080 (on 0x0mm) pclk=148350781
[    0.962718] tegradc tegradc.1: probed
[    0.965503] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels
[    0.968325] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 10 channels
[    0.968832] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized
[    0.969083] kfuse 7000fc00.kfuse: initialized
[    0.970754] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0
[    0.971551] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now
[    0.971576] vdd-cpu: 708 <--> 1322 mV at 708 mV 
[    0.971919] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed
[    0.972989] vdd-gpu: applied init 1000000uV constraint
[    0.973011] vdd-gpu: 710 <--> 1320 mV at 1002 mV 
[    0.973371] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed
[    0.976216] Console: switching to colour frame buffer device 240x67
[    0.976347] tegradc tegradc.1: fb registered
[    0.977410] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.977498] No Device Node present for smmu client: serial8250 !!
[    0.977517] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000)
[    0.977556] iommu: Adding device serial8250 to group 37
[    0.979379] console [ttyS0] disabled
[    0.979425] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra
[    0.982921] tegradc tegradc.1: DC initialized, skipping tegra_dc_program_mode.
[    0.982949] tegradc tegradc.1: hdmi: tmds rate:148351K prod-setting:prod_c_hdmi_75m_150m
[    0.983334] tegradc tegradc.1: hdmi: get RGB quant from REG programmed by BL.
[    0.983342] tegradc tegradc.1: hdmi: get YCC quant from REG programmed by BL.
[    1.051646] extcon-disp-state extcon:disp-state: cable 47 state 1
[    1.051649] Extcon AUX1(HDMI) enable
[    1.091170] tegradc tegradc.1: nominal-pclk:148351648 parent:148350781 div:1.0 pclk:148350781 146868084~161703244
[    1.571965] tegra-pcie 1003000.pcie: link 0 down, retrying
[    1.976330] tegra-pcie 1003000.pcie: link 0 down, retrying
[    2.380717] tegra-pcie 1003000.pcie: link 0 down, retrying
[    2.382733] tegra-pcie 1003000.pcie: link 0 down, ignoring
[    2.785084] tegra-pcie 1003000.pcie: link 1 down, retrying
[    3.189456] tegra-pcie 1003000.pcie: link 1 down, retrying
[    3.364121] tegradc tegradc.1: blank - powerdown
[    3.366528] console [ttyS0] enabled
[    3.368014] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART
[    3.368440] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART
[    3.368730] serial-tegra 70006300.serial: RX in PIO mode
[    3.368828] 70006300.serial: ttyTHS3 at MMIO 0x70006300 (irq = 66, base_baud = 0) is a TEGRA_UART
[    3.369940] [drm] Initialized
[    3.390085] brd: module loaded
[    3.395630] loop: module loaded
[    3.395731] tegra_profiler: version: 1.134, samples/io: 47/26
[    3.395848] tegra_profiler: auth: init
[    3.396464] nct1008_nct72 0-004c: starting parse dt
[    3.396606] nct1008_nct72 0-004c: !!!Found deprecated property!!!
[    3.396612] nct1008_nct72 0-004c: success parsing dt
[    3.397094] nct1008_nct72 0-004c: success in enabling tmp451 VDD rail
[    3.397836] THERMAL EST: found 2 subdevs
[    3.397844] THERMAL EST num_resources: 0
[    3.397850] [THERMAL EST subdev 0]
[    3.397860] [THERMAL EST subdev 1]
[    3.398346] thermal thermal_zone7: Registering thermal zone thermal_zone7 for type thermal-fan-est
[    3.398349] THERMAL EST: thz register success.
[    3.398523] THERMAL EST: end of probe, return err: 0
[    3.399944] hisi_sas: driver version v1.6
[    3.401305] tegra-ahci 70027000.sata: Missing devslp-active state
[    3.402334] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode
[    3.402344] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pmp pio slum part deso sadm apst 
[    3.403777] scsi host0: tegra_ahci
[    3.404377] scsi host1: tegra_ahci
[    3.404598] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 99
[    3.404601] ata2: DUMMY
[    3.409872] libphy: Fixed MDIO Bus: probed
[    3.410570] tun: Universal TUN/TAP device driver, 1.6
[    3.410573] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    3.412070] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    3.412074] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    3.412129] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
[    3.412133] igb: Copyright (c) 2007-2014 Intel Corporation.
[    3.412181] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
[    3.412183] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[    3.412231] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4
[    3.412235] Copyright(c) 1999 - 2017 Intel Corporation.
[    3.413369] PPP generic driver version 2.4.2
[    3.413597] PPP BSD Compression module registered
[    3.413601] PPP Deflate Compression module registered
[    3.413645] PPP MPPE Compression module registered
[    3.413653] NET: Registered protocol family 24
[    3.413685] extcon-disp-state extcon:disp-state: cable 47 state 0
[    3.413689] Extcon AUX1(HDMI) disable
[    3.413738] usbcore: registered new interface driver r8152
[    3.413783] usbcore: registered new interface driver asix
[    3.413831] usbcore: registered new interface driver ax88179_178a
[    3.413871] usbcore: registered new interface driver cdc_ether
[    3.413915] usbcore: registered new interface driver net1080
[    3.413962] usbcore: registered new interface driver cdc_subset
[    3.414005] usbcore: registered new interface driver zaurus
[    3.414060] usbcore: registered new interface driver cdc_ncm
[    3.414253] VFIO - User Level meta-driver version: 0.3
[    3.415680] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.415703] ehci-pci: EHCI PCI platform driver
[    3.415745] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.415757] ohci-pci: OHCI PCI platform driver
[    3.415802] ohci-platform: OHCI generic platform driver
[    3.419445] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP
[    3.420472] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0
[    3.421700] tegra-xusb 70090000.xusb: extcon 0: ffffffc0f9063000 id
[    3.423963] usbcore: registered new interface driver uas
[    3.424030] usbcore: registered new interface driver usb-storage
[    3.424156] usbcore: registered new interface driver usbserial
[    3.424586] tegra-xusb 70090000.xusb: Firmware timestamp: 2019-05-08 09:42:10 UTC, Version: 50.22 release
[    3.424691] tegra-xusb 70090000.xusb: xHCI Host Controller
[    3.424717] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1
[    3.425630] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010
[    3.425692] tegra-xusb 70090000.xusb: irq 62, io mem 0x70090000
[    3.425895] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    3.425901] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.425905] usb usb1: Product: xHCI Host Controller
[    3.425908] usb usb1: Manufacturer: Linux 4.9.140-tegra xhci-hcd
[    3.425912] usb usb1: SerialNumber: 70090000.xusb
[    3.426525] hub 1-0:1.0: USB hub found
[    3.426572] hub 1-0:1.0: 5 ports detected
[    3.427263] tegra-xusb 70090000.xusb: xHCI Host Controller
[    3.427280] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2
[    3.427368] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.427456] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[    3.427527] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.427531] usb usb2: Product: xHCI Host Controller
[    3.427534] usb usb2: Manufacturer: Linux 4.9.140-tegra xhci-hcd
[    3.427537] usb usb2: SerialNumber: 70090000.xusb
[    3.428113] hub 2-0:1.0: USB hub found
[    3.428147] hub 2-0:1.0: 4 ports detected
[    3.429313] nct1008_nct72 0-004c: LOC shutdown limit 120
[    3.429789] nct1008_nct72 0-004c: EXT shutdown limit 105
[    3.431996] tegra-xudc-new 700d0000.xudc: device count: 1
[    3.433286] tegra-xudc-new 700d0000.xudc: vbus state: 1
[    3.433303] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 0
[    3.464005] nct1008_nct72 0-004c: initial LOC temp: 31000 
[    3.464728] nct1008_nct72 0-004c: initial EXT temp: 31500 
[    3.465560] nct1008_nct72 0-004c: hi_b:0, lo_b:0
[    3.471264] nct1008_nct72 0-004c: nct1008_probe: initialized
[    3.527326] tegra-xusb-padctl 7009f000.xusb_padctl: power down UTMI pad 0
[    3.528614] tegra-usb-cd usb_cd: notification status (0x0, 0x1)
[    3.528701] tegra-usb-cd usb_cd: connected to SDP
[    3.528993] tegra-xudc-new 700d0000.xudc: device mode on: 0
[    3.529803] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 0
[    3.529960] tegra-xudc-new 700d0000.xudc: active: 0 => 1
[    3.533746] usb usb1: usb_suspend_both: status 0
[    3.547899] mousedev: PS/2 mouse device common for all mice
[    3.550982] usbcore: registered new interface driver xpad
[    3.589367] tegradc tegradc.1: unblank
[    3.601580] tegra-pcie 1003000.pcie: link 1 down, retrying
[    3.603614] tegra-pcie 1003000.pcie: link 1 down, ignoring
[    3.643532] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0
[    3.648249] rtc rtc1: alarm rtc device
[    3.648332] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1
[    3.648436] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock
[    3.651236] i2c /dev entries driver
[    3.652504] tegradc tegradc.1: nominal-pclk:83500000 parent:83500000 div:1.0 pclk:83500000 82665000~91015000
[    3.652880] tegradc tegradc.1: hdmi: tmds rate:83500K prod-setting:prod_c_hdmi_75m_150m
[    3.654376] tegradc tegradc.1: hdmi: get RGB quant from EDID.
[    3.654449] tegradc tegradc.1: hdmi: get YCC quant from EDID.
[    3.658997] max77620-power max77620-power: Event recorder REG_NVERC : 0x0
[    3.667066] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2
[    3.667238] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4
[    3.668808] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC
[    3.668838] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC
[    3.669172] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[    3.669186] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC
[    3.669198] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC
[    3.669421] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[    3.669425] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature 2147483647 forced to 127000
[    3.669437] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC
[    3.669446] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature
[    3.669784] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19
[    3.672818] tegra_aotag tegra-aotag: Registering sensor 0
[    3.672958] tegra_aotag tegra-aotag: Invalid temp readout
[    3.672974] tegra_aotag tegra-aotag: Bound to TZ : ID 0
[    3.672987] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0
[    3.675414] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered
[    3.676640] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered
[    3.677819] parse_throttle_dt_data: Num cap clks = 6
[    3.677835] parse_throttle_dt_data: clk=cclk_g type=2
[    3.677895] parse_throttle_dt_data: clk=gpu type=4
[    3.677995] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0
[    3.678037] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0
[    3.678084] parse_throttle_dt_data: clk=cap.throttle.sclk type=0
[    3.678090] parse_throttle_dt_data: clk=emc type=3
[    3.679287] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[    3.679644] tegra_throttle_probe: probe successful. #cdevs=4
[    3.681931] FAN: coudln't get the regulator
[    3.683491] tegra-wdt 60005100.watchdog: Tegra WDT enabled on probe. Timeout = 120 seconds.
[    3.684613] tegra-wdt 60005100.watchdog: initialized (timeout = 120 sec, nowayout = 1)
[    3.686982] device-mapper: uevent: version 1.0.3
[    3.688411] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
[    3.709057] extcon-disp-state extcon:disp-state: cable 47 state 1
[    3.709096] Extcon AUX1(HDMI) enable
[    3.710851] tegra210-cpufreq cpufreq: probe()...completed
[    3.710891] tegradc tegradc.1: sync windows ret = 250
[    3.711657] sdhci: Secure Digital Host Controller Interface driver
[    3.711659] sdhci: Copyright(c) Pierre Ossman
[    3.711660] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.712004] sdhci-tegra sdhci-tegra.3: Client registration for eMC Successful
[    3.715181] sdhci-tegra sdhci-tegra.1: Client registration for eMC Successful
[    3.716934] sdhci-tegra sdhci-tegra.0: Got CD GPIO
[    3.716958] sdhci-tegra sdhci-tegra.0: Got WP GPIO
[    3.717302] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful
[    3.719771] ata1: SATA link down (SStatus 0 SControl 300)
[    3.721335] tegra-se 70012000.se: tegra_se_probe: complete
[    3.721871] hidraw: raw HID events driver (C) Jiri Kosina
[    3.723127] usbcore: registered new interface driver usbhid
[    3.723129] usbhid: USB HID core driver
[    3.725921] tegra-i2c 7000c400.i2c: no acknowledge from address 0x42
[    3.725953] ina3221x 1-0042: ina3221 reset failure status: 0xffffff87
[    3.726057] ina3221x: probe of 1-0042 failed with error -121
[    3.726301] tegra-i2c 7000c400.i2c: no acknowledge from address 0x43
[    3.726330] ina3221x 1-0043: ina3221 reset failure status: 0xffffff87
[    3.726415] ina3221x: probe of 1-0043 failed with error -121
[    3.727396] tegra21x_actmon 6000c800.actmon: in actmon_register()...
[    3.727562] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all
[    3.729256] nvpmodel: initialized successfully
[    3.730198] usbcore: registered new interface driver snd-usb-audio
[    3.730249] No Device Node present for smmu client: snd-soc-dummy !!
[    3.730253] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000)
[    3.730269] iommu: Adding device snd-soc-dummy to group 38
[    3.738113] tegra210-i2s tegra210-i2s.0: Missing prop fsync-width for I2S0
[    3.738996] tegra210-i2s tegra210-i2s.2: Missing prop fsync-width for I2S2
[    3.739160] tegra210-i2s tegra210-i2s.3: Missing prop fsync-width for I2S3
[    3.739336] tegra210-i2s tegra210-i2s.4: Missing prop fsync-width for I2S4
[    3.742668] OPE platform probe
[    3.742772] OPE platform probe successful
[    3.742795] OPE platform probe
[    3.742876] OPE platform probe successful
[    3.744358] tegra-asoc: sound: This is a dummy codec
[    3.750340] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input0
[    3.755145] mmc0: SDHCI controller on sdhci-tegra.3 [sdhci-tegra.3] using ADMA 64-bit with 64 bit addr
[    3.767100] mmc1: SDHCI controller on sdhci-tegra.1 [sdhci-tegra.1] using ADMA 64-bit with 64 bit addr
[    3.771402] mmc2: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA 64-bit with 64 bit addr
[    3.772022] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok
[    3.772144] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok
[    3.772256] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok
[    3.772371] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok
[    3.772488] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok
[    3.772604] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok
[    3.772738] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok
[    3.772851] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok
[    3.772967] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok
[    3.773090] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok
[    3.784298] u32 classifier
[    3.784299]     Actions configured
[    3.784366] Initializing XFRM netlink socket
[    3.785117] NET: Registered protocol family 10
[    3.785764] NET: Registered protocol family 17
[    3.785774] NET: Registered protocol family 15
[    3.785838] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    3.785877] Bluetooth: RFCOMM socket layer initialized
[    3.785885] Bluetooth: RFCOMM ver 1.11
[    3.785889] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    3.785892] Bluetooth: HIDP socket layer initialized
[    3.785908] 9pnet: Installing 9P2000 support
[    3.785940] Key type dns_resolver registered
[    3.792114] Registered cp15_barrier emulation handler
[    3.799867] Registered setend emulation handler
[    3.800873] registered taskstats version 1
[    3.801451] Adding domain ve2-pd to PM domain host1x-pd
[    3.801709] Adding domain ve-pd to PM domain host1x-pd
[    3.804184] isp 54600000.isp: initialized
[    3.805283] isp 54680000.isp: initialized
[    3.808209] tegra-pcie 1003000.pcie: PCIE: no end points detected
[    3.808424] tegra-pcie 1003000.pcie: PCIE: Disable power rails
[    3.812357] mmc0: new HS400 Enhanced strobe MMC card at address 0001
[    3.812707] mmcblk0: mmc0:0001 016G32 14.7 GiB 
[    3.815130] last reset is due to software reset
[    3.815132] KERNEL: PMC reset status reg: 0x3
[    3.815213] BL: PMC reset status reg: 0x3
[    3.815215] BL: PMIC poweroff Event Recorder: 0x0
[    3.816866] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB
[    3.816930] clk_cbus_recalc_rate: no gbus parent
[    3.816934] clk_cbus_round_rate: no gbus parent
[    3.816935] clk_cbus_round_rate: no gbus parent
[    3.816941] clk_cbus_recalc_rate: no gbus parent
[    3.817299] clk_cbus_recalc_rate: no gbus parent
[    3.817301] clk_cbus_round_rate: no gbus parent
[    3.817302] clk_cbus_round_rate: no gbus parent
[    3.817305] clk_cbus_recalc_rate: no gbus parent
[    3.817319] tegra_dvfs: GPU-cap: registered
[    3.817371] tegra dvfs: vdd-cpu: nominal 1226mV, offset 708000uV, step 19200uV, scaling enabled
[    3.817373] tegra dvfs: vdd-core: nominal 1075mV, offset 600000uV, step 12500uV, scaling enabled
[    3.817374] tegra dvfs: vdd-gpu: nominal 1100mV, offset 710000uV, step 10000uV, scaling enabled
[    3.818961] tegra_dvfs: vdd-gpu-vts: registered
[    3.821017] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB
[    3.821971] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered
[    3.822825] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered
[    3.825163] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB
[    3.825606] input: gpio-keys as /devices/gpio-keys/input/input1
[    3.826466]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19
[    3.865093] tegra_rtc 7000e000.rtc: setting system clock to 2019-08-20 19:09:33 UTC (1566328173)
[    3.866392] vi 54080000.vi: vi_probe: ++
[    3.869096] vi 54080000.vi: initialized
[    3.870947] vi 54080000.vi: ep of_device is not enabled /host1x/vi/ports/port@0/endpoint.
[    3.870951] vi 54080000.vi: ep of_device is not enabled /host1x/vi/ports/port@1/endpoint.
[    3.870954] vi 54080000.vi: ep of_device is not enabled /host1x/vi/ports/port@2/endpoint.
[    3.870956] vi 54080000.vi: ep of_device is not enabled /host1x/vi/ports/port@3/endpoint.
[    3.873299] mmcblk mmc0:0001: Card claimed for testing.
[    3.875188] Disable partitions left on by BL
[    3.875190]   disb
[    3.875269] bwmgr: missing cdev-type property
[    3.875985] DRAM derating cdev registered.
[    3.877409] vdd-cpu-fixed: disabling
[    3.877417] vdd-cam-hv: disabling
[    3.878176] avdd-ts-hv: disabling
[    3.879203] vdd-ts: disabling
[    3.880246] max77620-gpio7: disabling
[    3.882306] lcd-bl-en: disabling
[    3.882310] en-vdd-sd: disabling
[    3.882312] aux-3v3: disabling
[    3.882313] snsr_pm: disabling
[    3.882315] vdd-disp-3v0: disabling
[    3.882317] usb-vbus1: disabling
[    3.882320] en-vdd-vcm-2v8: disabling
[    3.883340] ALSA device list:
[    3.883342]   #0: tegra-hda at 0x70038000 irq 81
[    3.883343]   #1: tegra-snd-t210ref-mobile-rt565x
[    4.008263] mmc1: hw tuning done ...
[    4.011695] mmc1: new ultra high speed SDR104 SDIO card at address 0001
[    5.607847] extcon-disp-state extcon:disp-state: cable 40 state 1
[    5.610596] Freeing unused kernel memory: 8576K
[    5.620301] Extcon HDMI: HPD enabled
[    5.620325] tegradc tegradc.1: hdmi: plugged
[    5.644069] L4T-INITRD Build DATE: Tue Aug 20 19:09:35 UTC 2019
[    5.654620] Root device found: mmcblk0p1
[    5.660440] Found dev node: /dev/mmcblk0p1
[    5.682147] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[    5.691936] Rootfs mounted over mmcblk0p1
[    5.713202] Switching from initrd to actual rootfs
[    5.804323] ip_tables: (C) 2000-2006 Netfilter Core Team
[    5.820618] cgroup: cgroup2: unknown option "nsdelegate"
[    5.834862] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[    5.858949] systemd[1]: Detected architecture arm64.
[    5.891156] systemd[1]: Set hostname to <tegra-ubuntu>.
[    5.900366] random: systemd: uninitialized urandom read (16 bytes read)
[    5.908016] systemd[1]: Initializing machine ID from random generator.
[    5.974033] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
[    5.993303] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[    6.088739] random: systemd: uninitialized urandom read (16 bytes read)
[    6.096613] systemd[1]: Reached target Swap.
[    6.103812] random: systemd: uninitialized urandom read (16 bytes read)
[    6.113259] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    6.126994] systemd[1]: Created slice System Slice.
[    6.134745] systemd[1]: Listening on udev Control Socket.
[    6.212779] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
[    6.293819] nvgpu: 57000000.gpu           gm20b_init_clk_setup_sw:1268 [INFO]  GPCPLL initial settings: NA mode, M=1, N=34, P=3 (id = 1)
[    7.084563] using random self ethernet address
[    7.090183] using random host ethernet address
[    7.132066] using random self ethernet address
[    7.143122] using random host ethernet address
[    7.272307] random: crng init done
[    7.276669] random: 7 urandom warning(s) missed due to ratelimiting
[   10.418820] Please complete system configuration setup on desktop to proceed...