<\0>[0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de)<\r><\n> [0000.130] Processing in cold boot mode Bootloader 2<\r><\n> [0000.135] A02 Bootrom Patch rev = 1023<\r><\n> [0000.138] Power-up reason: pmc por<\r><\n> [0000.141] No Battery Present<\r><\n> [0000.144] pmic max77620 reset reason<\r><\n> [0000.147] pmic max77620 NVERC : 0x40<\r><\n> [0000.151] RamCode = 1<\r><\n> [0000.153] Platform has DDR4 type RAM<\r><\n> [0000.156] max77620 disabling SD1 Remote Sense<\r><\n> [0000.161] Setting DDR voltage to 1125mv<\r><\n> [0000.165] Serial Number of Pmic Max77663: 0x1907f7<\r><\n> [0000.172] Entering ramdump check<\r><\n> [0000.175] Get RamDumpCarveOut = 0x0<\r><\n> [0000.179] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8<\r><\n> [0000.184] Last reboot was clean, booting normally!<\r><\n> [0000.188] Sdram initialization is successful <\r><\n> [0000.192] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000<\r><\n> [0000.199] Lp0 Carveout Base=0x00000000ff800000 Size=0x00000000<\r><\n> [0000.204] BpmpFw Carveout Base=0x00000000ff800000 Size=0x00000000<\r><\n> [0000.210] GSC1 Carveout Base=0x00000000ff800000 Size=0x00000000<\r><\n> [0000.216] Resize the SecureOs Carveout to 0x00100000<\r><\n> [0000.221] GSC2 Carveout Base=0x00000000ff900000 Size=0x00100000<\r><\n> [0000.226] GSC4 Carveout Base=0x00000000ff800000 Size=0x00000000<\r><\n> [0000.232] GSC5 Carveout Base=0x00000000ff800000 Size=0x00000000<\r><\n> [0000.238] GSC3 Carveout Base=0x00000000bf800000 Size=0x00200000<\r><\n> [0000.244] RamDump Carveout Base=0x0000000000000000 Size=0x00000000<\r><\n> [0000.250] Platform-DebugCarveout: 0<\r><\n> [0000.253] Nck Carveout Base=0x00000000ff800000 Size=0x00000000<\r><\n> [0000.259] Non secure mode, and RB not enabled.<\r><\n> [0000.263] BoardID = 3448, SKU = 0x3<\r><\n> [0000.266] QSPI-ONLY: SkipQspiOnlyFlag = 0<\r><\n> [0000.270] Nano-SD: checking PT table on QSPI ...<\r><\n> [0000.274] Read PT from (2:0)<\r><\n> [0000.290] Using BFS PT to query partitions <\r><\n> [0000.296] Loading Tboot-CPU binary<\r><\n> [0000.324] Verifying TBC in OdmNonSecureSBK mode<\r><\n> [0000.334] Bootloader load address is 0xa0000000, entry address is 0xa0000258<\r><\n> [0000.341] Bootloader downloaded successfully.<\r><\n> [0000.345] Downloaded Tboot-CPU binary to 0xa0000258<\r><\n> [0000.350] MAX77620_GPIO5 configured<\r><\n> [0000.353] CPU power rail is up<\r><\n> [0000.356] CPU clock enabled<\r><\n> [0000.360] Performing RAM repair<\r><\n> [0000.363] Updating A64 Warmreset Address to 0xa00002e9<\r><\n> [0000.368] BoardID = 3448, SKU = 0x3<\r><\n> [0000.371] QSPI-ONLY: SkipQspiOnlyFlag = 0<\r><\n> [0000.375] Nano-SD: checking PT table on QSPI ...<\r><\n> [0000.379] Loading NvTbootBootloaderDTB<\r><\n> [0000.446] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode<\r><\n> [0000.519] Bootloader DTB Load Address: 0x83000000<\r><\n> [0000.524] BoardID = 3448, SKU = 0x3<\r><\n> [0000.527] QSPI-ONLY: SkipQspiOnlyFlag = 0<\r><\n> [0000.531] Nano-SD: checking PT table on QSPI ...<\r><\n> [0000.535] Loading NvTbootKernelDTB<\r><\n> [0000.601] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode<\r><\n> [0000.674] Kernel DTB Load Address: 0x83100000<\r><\n> [0000.678] BoardID = 3448, SKU = 0x3<\r><\n> [0000.682] QSPI-ONLY: SkipQspiOnlyFlag = 0<\r><\n> [0000.685] Nano-SD: checking PT table on QSPI ...<\r><\n> [0000.691] Loading cboot binary<\r><\n> [0000.807] Verifying EBT in OdmNonSecureSBK mode<\r><\n> [0000.849] Bootloader load address is 0x92c00000, entry address is 0x92c00258<\r><\n> [0000.856] Bootloader downloaded successfully.<\r><\n> [0000.860] BoardID = 3448, SKU = 0x3<\r><\n> [0000.863] QSPI-ONLY: SkipQspiOnlyFlag = 0<\r><\n> [0000.867] Nano-SD: checking PT table on QSPI ...<\r><\n> [0000.872] PT: Partition NCT NOT found ! <\r><\n> [0000.876] Warning: Find Partition via PT Failed<\r><\n> [0000.880] Next binary entry address: 0x92c00258 <\r><\n> [0000.884] BoardId: 3448<\r><\n> [0000.889] Overriding pmu board id with proc board id<\r><\n> [0000.894] Display board id is not available <\r><\n> [0000.898] No Bpmp FW loaded<\r><\n> [0000.901] Not loading WB0 as no bpmp/sc7entry fw<\r><\n> [0000.905] Set NvDecSticky Bits<\r><\n> [0000.909] GSC2 address ff93fffc value c0edbbcc<\r><\n> [0000.915] GSC MC Settings done<\r><\n> [0000.918] BoardID = 3448, SKU = 0x3<\r><\n> [0000.921] QSPI-ONLY: SkipQspiOnlyFlag = 0<\r><\n> [0000.925] Nano-SD: checking PT table on QSPI ...<\r><\n> [0000.930] TOS Image length 53680<\r><\n> [0000.933] Monitor size 53680<\r><\n> [0000.936] OS size 0<\r><\n> [0000.951] Secure Os AES-CMAC Verification Success!<\r><\n> [0000.956] TOS image cipher info: plaintext<\r><\n> [0000.960] Loading and Validation of Secure OS Successful<\r><\n> [0000.975] NvTbootPackSdramParams: start. <\r><\n> [0000.981] NvTbootPackSdramParams: done. <\r><\n> [0000.984] Tegraboot started after 51827 us<\r><\n> [0000.988] Basic modules init took 909134 us<\r><\n> [0000.992] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB<\r><\n> [0000.998] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB<\r><\n> [0001.003] Next stage binary read took 11286 us<\r><\n> [0001.008] Carveout took -63810 us<\r><\n> [0001.011] CPU initialization took 99947 us<\r><\n> [0001.015] Total time taken by TegraBoot 956557 us<\r><\n> <\r><\n> [0001.019] Starting CPU & Halting co-processor <\r><\n> <\r><\n> 64NOTICE: BL31: v1.3(release):5b49e7f80<\r><\n> NOTICE: BL31: Built : 08:37:40, Feb 19 2021<\r><\n> ERROR: Error initializing runtime service trusty_fast<\r><\n> [0001.141] RamCode = 1<\r><\n> [0001.143] get_emc_table_offset: Can't find emc-table node<\r><\n> [0001.148] LPDDR4 Training: Can't find emc-table node<\r><\n> [0001.184] <\r><\n> [0001.185] Debug Init done<\r><\n> [0001.188] Marked DTB cacheable<\r><\n> [0001.190] Bootloader DTB loaded at 0x83000000<\r><\n> [0001.195] Marked DTB cacheable<\r><\n> [0001.198] Kernel DTB loaded at 0x83100000<\r><\n> [0001.202] DeviceTree Init done<\r><\n> [0001.215] Pinmux applied successfully<\r><\n> [0001.219] gicd_base: 0x50041000<\r><\n> [0001.223] gicc_base: 0x50042000<\r><\n> [0001.226] Interrupts Init done<\r><\n> [0001.230] Using base:0x60005090 & irq:208 for tick-timer<\r><\n> [0001.235] Using base:0x60005098 for delay-timer<\r><\n> [0001.240] platform_init_timer: DONE<\r><\n> [0001.243] Timer(tick) Init done<\r><\n> [0001.247] osc freq = 38400 khz<\r><\n> [0001.251] <\r><\n> [0001.252] Welcome to L4T Cboot<\r><\n> [0001.255] <\r><\n> [0001.256] Cboot Version: 00.00.2018.01-t210-39562017<\r><\n> [0001.261] calling constructors<\r><\n> [0001.264] initializing heap<\r><\n> [0001.267] initializing threads<\r><\n> [0001.270] initializing timers<\r><\n> [0001.272] creating bootstrap completion thread<\r><\n> [0001.277] top of bootstrap2()<\r><\n> [0001.280] CPU: ARM Cortex A57<\r><\n> [0001.283] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000<\r><\n> [0001.287] initializing platform<\r><\n> [0001.295] Manufacturer: MF = 0xc2, ID MSB = 0x25<\r><\n> [0001.299] ID LSB = 0x36, ID-CFI len = 194 bytes<\r><\n> [0001.304] Macronix QSPI chip present<\r><\n> [0001.307] SPI device register<\r><\n> [0001.310] init boot device<\r><\n> [0001.313] allocating memory for boot device(SPI)<\r><\n> [0001.317] registering boot device<\r><\n> [0001.326] QSPI bdev is already initialized<\r><\n> [0001.330] Enable APE clock<\r><\n> [0001.332] Un-powergate APE partition<\r><\n> [0001.336] of_register: registering tegra_udc to of_hal<\r><\n> [0001.341] of_register: registering inv20628-driver to of_hal<\r><\n> [0001.347] of_register: registering ads1015-driver to of_hal<\r><\n> [0001.352] of_register: registering lp8557-bl-driver to of_hal<\r><\n> [0001.358] of_register: registering bq2419x_charger to of_hal<\r><\n> [0001.363] of_register: registering bq27441_fuel_gauge to of_hal<\r><\n> [0001.375] gpio framework initialized<\r><\n> [0001.378] of_register: registering tca9539_gpio to of_hal<\r><\n> [0001.384] of_register: registering tca9539_gpio to of_hal<\r><\n> [0001.389] of_register: registering i2c_bus_driver to of_hal<\r><\n> [0001.395] of_register: registering i2c_bus_driver to of_hal<\r><\n> [0001.400] of_register: registering i2c_bus_driver to of_hal<\r><\n> [0001.406] pmic framework initialized<\r><\n> [0001.409] of_register: registering max77620_pmic to of_hal<\r><\n> [0001.415] regulator framework initialized<\r><\n> [0001.419] of_register: registering tps65132_bl_driver to of_hal<\r><\n> [0001.425] initializing target<\r><\n> [0001.431] gpio_driver_register: register 'tegra_gpio_driver' driver<\r><\n> [0001.439] board ID = D78, board SKU = 3<\r><\n> [0001.442] Skipping Z3!<\r><\n> [0001.447] fixed regulator driver initialized<\r><\n> [0001.465] initializing OF layer<\r><\n> [0001.468] NCK carveout not present<\r><\n> [0001.471] Skipping dts_overrides<\r><\n> [0001.475] of_children_init: Ops found for compatible string nvidia,tegra210-i2c<\r><\n> [0001.493] I2C Bus Init done<\r><\n> [0001.495] of_children_init: Ops found for compatible string nvidia,tegra210-i2c<\r><\n> [0001.505] I2C Bus Init done<\r><\n> [0001.508] of_children_init: Ops found for compatible string nvidia,tegra210-i2c<\r><\n> [0001.519] I2C Bus Init done<\r><\n> [0001.521] of_children_init: Ops found for compatible string nvidia,tegra210-i2c<\r><\n> [0001.532] I2C Bus Init done<\r><\n> [0001.534] of_children_init: Ops found for compatible string nvidia,tegra210-i2c<\r><\n> [0001.545] I2C Bus Init done<\r><\n> [0001.547] of_children_init: Ops found for compatible string maxim,max77620<\r><\n> [0001.558] max77620_init using irq 118<\r><\n> [0001.563] register 'maxim,max77620' pmic<\r><\n> [0001.567] gpio_driver_register: register 'max77620-gpio' driver<\r><\n> [0001.573] of_children_init: Ops found for compatible string nvidia,tegra210-i2c<\r><\n> [0001.584] I2C Bus Init done<\r><\n> [0001.587] NCK carveout not present<\r><\n> [0001.597] Find /i2c@7000c000's alias i2c0<\r><\n> [0001.601] get eeprom at 1-a0, size 256, type 0<\r><\n> [0001.610] Find /i2c@7000c500's alias i2c2<\r><\n> [0001.614] get eeprom at 3-a0, size 256, type 0<\r><\n> [0001.618] get eeprom at 3-ae, size 256, type 0<\r><\n> [0001.622] pm_ids_update: Updating 1,a0, size 256, type 0<\r><\n> [0001.628] I2C slave not started<\r><\n> [0001.631] I2C write failed<\r><\n> [0001.633] Writing offset failed<\r><\n> [0001.636] eeprom_init: EEPROM read failed<\r><\n> [0001.640] pm_ids_update: eeprom init failed<\r><\n> [0001.644] pm_ids_update: Updating 3,a0, size 256, type 0<\r><\n> [0001.675] pm_ids_update: The pm board id is 3448-0003-400<\r><\n> [0001.681] Adding plugin-manager/ids/3448-0003-400=/i2c@7000c500:module@0x50<\r><\n> [0001.690] pm_ids_update: pm id update successful<\r><\n> [0001.694] pm_ids_update: Updating 3,ae, size 256, type 0<\r><\n> [0001.724] pm_ids_update: The pm board id is 3542-0000-201<\r><\n> [0001.731] Adding plugin-manager/ids/3542-0000-201=/i2c@7000c500:module@0x57<\r><\n> [0001.739] pm_ids_update: pm id update successful<\r><\n> [0001.769] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)<\r><\n> [0001.775] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB<\r><\n> [0001.783] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)<\r><\n> [0001.789] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB<\r><\n> [0001.797] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:2f:0e:17<\r><\n> [0001.803] Plugin Manager: Parse ODM data 0x000a4000<\r><\n> [0001.816] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 <\r><\n> [0001.830] Find /i2c@7000c000's alias i2c0<\r><\n> [0001.834] get eeprom at 1-a0, size 256, type 0<\r><\n> [0001.843] Find /i2c@7000c500's alias i2c2<\r><\n> [0001.847] get eeprom at 3-a0, size 256, type 0<\r><\n> [0001.851] get eeprom at 3-ae, size 256, type 0<\r><\n> [0001.856] pm_ids_update: Updating 1,a0, size 256, type 0<\r><\n> [0001.861] I2C slave not started<\r><\n> [0001.864] I2C write failed<\r><\n> [0001.867] Writing offset failed<\r><\n> [0001.870] eeprom_init: EEPROM read failed<\r><\n> [0001.874] pm_ids_update: eeprom init failed<\r><\n> [0001.878] pm_ids_update: Updating 3,a0, size 256, type 0<\r><\n> [0001.908] pm_ids_update: The pm board id is 3448-0003-400<\r><\n> [0001.914] Adding plugin-manager/ids/3448-0003-400=/i2c@7000c500:module@0x50<\r><\n> [0001.921] pm_ids_update: pm id update successful<\r><\n> [0001.926] pm_ids_update: Updating 3,ae, size 256, type 0<\r><\n> [0001.956] pm_ids_update: The pm board id is 3542-0000-201<\r><\n> [0001.962] Adding plugin-manager/ids/3542-0000-201=/i2c@7000c500:module@0x57<\r><\n> [0001.969] pm_ids_update: pm id update successful<\r><\n> [0001.999] Add serial number:1424120058067 as DT property<\r><\n> [0002.007] Applying platform configs<\r><\n> [0002.014] platform-init is not present. Skipping<\r><\n> [0002.018] calling apps_init()<\r><\n> [0002.024] Couldn't find GPT header<\r><\n> [0002.029] Proceeding to Cold Boot<\r><\n> [0002.032] starting app android_boot_app<\r><\n> [0002.036] Device state: unlocked<\r><\n> [0002.039] display console init<\r><\n> [0002.047] could not find regulator<\r><\n> [0002.050] hdmi cable connected<\r><\n> [0002.066] edid read success<\r><\n> [0002.068] width = 640, height = 480, frequency = 25174825<\r><\n> [0002.074] width = 640, height = 480, frequency = 25174825<\r><\n> [0002.079] width = 640, height = 48DT entry for leds-pwm not found<\r><\n> 0[0002.089] , frequency = 25174825<\r><\n> [0002.092] width = 640, height = 480, frequency = 25174825<\r><\n> [0002.097] width = 1280, height = 1024, frequency = 108000000<\r><\n> [0002.103] Best mode Width = 640, Height = 480, freq = 25174825<\r><\n> [0002.110] tmds-config node not found<\r><\n> [0002.115] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts<\r><\n> [0002.129] setting 'vdd-1v8' regulator to 1800000 micro volts<\r><\n> [0002.137] could not find regulator<\r><\n> [0002.140] could not find regulator<\r><\n> [0002.143] could not find regulator<\r><\n> [0002.172] using default cmu settings<\r><\n> [0002.176] dc_hdmi_enable, starting HDMI initialisation<\r><\n> [0002.182] dc_hdmi_enable, HDMI initialisation complete<\r><\n> [0002.187] list and configure display window<\r><\n> [0002.192] display console init completed<\r><\n> [0002.199] subnode volume_up is not found !<\r><\n> [0002.203] subnode back is not found !<\r><\n> [0002.207] subnode volume_down is not found !<\r><\n> [0002.211] subnode menu is not found !<\r><\n> [0002.214] Gpio keyboard init success<\r><\n> [0002.295] found decompressor handler: lz4-legacy<\r><\n> [0002.309] decompressing blob (type 1)...<\r><\n> [0002.375] load_bmp_blob: panelresolution=480 type=0<\r><\n> [0002.450] decompressor handler not found<\r><\n> [0002.453] load_firmware_blob: Firmware blob loaded, entries=2<\r><\n> [0002.459] XUSB blob version 0 size 124416 @ 0x92dee28c<\r><\n> [0002.465] -------> se_aes_verify_sbk_clear: 747<\r><\n> [0002.470] se_aes_verify_sbk_clear: Error<\r><\n> [0002.474] SE operation failed<\r><\n> [0002.476] bl_battery_charging: connected to external power supply<\r><\n> [0002.489] device_query_partition_size: failed to open partition spiflash0:MSC !<\r><\n> [0002.496] MSC Partition not found<\r><\n> [0002.502] device_query_partition_size: failed to open partition spiflash0:USP !<\r><\n> [0002.509] USP partition read failed!<\r><\n> [0002.513] blob_init: blob-partition USP header read failed<\r><\n> [0002.518] android_boot Unable to update recovery partition<\r><\n> [0002.524] kfs_getpartname: name = LNX<\r><\n> [0002.527] Loading kernel from LNX<\r><\n> [0002.537] Found 19 BFS partitions in "spiflash0"<\r><\n> [0002.856] load kernel from storage<\r><\n> [0002.861] decompressor handler not found<\r><\n> [0003.125] Successfully loaded kernel and ramdisk images<\r><\n> [0003.130] board ID = D78, board SKU = 3<\r><\n> [0003.135] sdmmc node status = okay<\r><\n> [0003.138] sdcard instance = 0<\r><\n> [0003.141] sdcard gpio handle 0x5b<\r><\n> [0003.144] sdcard gpio pin 0xc9<\r><\n> [0003.147] sdcard gpio flags 0x0<\r><\n> [0003.150] vmmc-supply 0x9e<\r><\n> [0003.153] cd_gpio_pin = 201<\r><\n> [0003.155] pin_state = 0<\r><\n> [0003.158] Found sdcard<\r><\n> [0003.160] SD-card IS present ...<\r><\n> [0003.163] load_and_boot_kernel: SD card detected OK<\r><\n> [0003.169] load_bmp_blob: panelresolution=480 type=0<\r><\n> [0003.240] display bmp image done<\r><\n> [0003.243] NCK carveout not present<\r><\n> [0003.247] Skipping dts_overrides<\r><\n> [0003.250] NCK carveout not present<\r><\n> [0003.260] Find /i2c@7000c000's alias i2c0<\r><\n> [0003.264] get eeprom at 1-a0, size 256, type 0<\r><\n> [0003.273] Find /i2c@7000c500's alias i2c2<\r><\n> [0003.276] get eeprom at 3-a0, size 256, type 0<\r><\n> [0003.281] get eeprom at 3-ae, size 256, type 0<\r><\n> [0003.285] pm_ids_update: Updating 1,a0, size 256, type 0<\r><\n> [0003.291] I2C slave not started<\r><\n> [0003.294] I2C write failed<\r><\n> [0003.296] Writing offset failed<\r><\n> [0003.299] eeprom_init: EEPROM read failed<\r><\n> [0003.303] pm_ids_update: eeprom init failed<\r><\n> [0003.307] pm_ids_update: Updating 3,a0, size 256, type 0<\r><\n> [0003.337] pm_ids_update: The pm board id is 3448-0003-400<\r><\n> [0003.344] Adding plugin-manager/ids/3448-0003-400=/i2c@7000c500:module@0x50<\r><\n> [0003.353] pm_ids_update: pm id update successful<\r><\n> [0003.357] pm_ids_update: Updating 3,ae, size 256, type 0<\r><\n> [0003.387] pm_ids_update: The pm board id is 3542-0000-201<\r><\n> [0003.393] Adding plugin-manager/ids/3542-0000-201=/i2c@7000c500:module@0x57<\r><\n> [0003.401] pm_ids_update: pm id update successful<\r><\n> [0003.432] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)<\r><\n> [0003.438] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB<\r><\n> [0003.445] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)<\r><\n> [0003.451] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB<\r><\n> [0003.460] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:2f:0e:17<\r><\n> [0003.466] Plugin Manager: Parse ODM data 0x000a4000<\r><\n> [0003.478] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 <\r><\n> [0003.487] Add serial number:1424120058067 as DT property<\r><\n> [0003.495] Updated bpmp info to DTB<\r><\n> [0003.499] Updated initrd info to DTB<\r><\n> [0003.503] "proc-board" doesn't exist, creating <\r><\n> [0003.509] Updated board info to DTB<\r><\n> [0003.512] "pmu-board" doesn't exist, creating <\r><\n> [0003.518] Updated board info to DTB<\r><\n> [0003.522] "display-board" doesn't exist, creating <\r><\n> [0003.528] Updated board info to DTB<\r><\n> [0003.531] "reset" doesn't exist, creating <\r><\n> [0003.536] Updated reset info to DTB<\r><\n> [0003.539] Cmdline: tegraid=21.1.2.0.0 ddr_die=2048M@2048M section=256M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x140000@0x92ca9000 is_hdmi_initialised=1 <\r><\n> [0003.576] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 <\r><\n> [0003.581] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 <\r><\n> [0003.594] Updated bootarg info to DTB<\r><\n> [0003.598] Adding uuid 00000001644608880400000010ff82c0 to DT<\r><\n> [0003.604] Adding eks info 0 to DT<\r><\n> [0003.610] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7<\r><\n> [0003.616] Updated memory info to DTB<\r><\n> [0003.624] set vdd_core voltage to 1075 mv<\r><\n> [0003.627] setting 'vdd-core' regulator to 1075000 micro volts<\r><\n> [0003.633] Found secure-pmc; disable BPMP<\r><\n> <\r><\n> <\r><\n> U-Boot 2020.04-g6b630d64fd (Feb 19 2021 - 08:37:46 -0800)<\r><\n> <\r><\n> SoC: tegra210<\r><\n> Model: NVIDIA Jetson Nano Developer Kit<\r><\n> Board: NVIDIA P3450-0000<\r><\n> DRAM: 2 GiB<\r><\n> MMC: sdhci@700b0000: 1, sdhci@700b0600: 0<\r><\n> Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB<\r><\n> *** Warning - bad CRC, using default environment<\r><\n> <\r><\n> In: serial<\r><\n> Out: serial<\r><\n> Err: serial<\r><\n> Net: No ethernet found.<\r><\n> Hit any key to stop autoboot: 2 <\b><\b><\b> 1 <\b><\b><\b> 0 <\r><\n> switch to partitions #0, OK<\r><\n> mmc1 is current device<\r><\n> Scanning mmc 1:1...<\r><\n> Found /boot/extlinux/extlinux.conf<\r><\n> Retrieving file: /boot/extlinux/extlinux.conf<\r><\n> 845 bytes read in 25 ms (32.2 KiB/s)<\r><\n> 1:<9>primary kernel<\r><\n> Retrieving file: /boot/initrd<\r><\n> 7159841 bytes read in 328 ms (20.8 MiB/s)<\r><\n> Retrieving file: /boot/Image<\r><\n> 34338824 bytes read in 1502 ms (21.8 MiB/s)<\r><\n> append: tegraid=21.1.2.0.0 ddr_die=2048M@2048M section=256M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x140000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 <\r><\n> ## Flattened Device Tree blob at 83100000<\r><\n> Booting using the fdt blob at 0x83100000<\r><\n> ERROR: reserving fdt memory region failed (addr=0 size=0)<\r><\n> ERROR: reserving fdt memory region failed (addr=0 size=0)<\r><\n> Using Device Tree in place at 0000000083100000, end 000000008317e68d<\r><\n> copying carveout for /host1x@50000000/dc@54200000...<\r><\n> copying carveout for /host1x@50000000/dc@54240000...<\r><\n> <\r><\n> Starting kernel ...<\r><\n> <\r><\n> [ 0.000000] Booting Linux on physical CPU 0x0<\r><\n> [ 0.000000] Linux version 4.9.201-tegra (buildbrain@mobile-u64-5294-d8000) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Fri Feb 19 08:40:32 PST 2021<\r><\n> [ 0.000000] Boot CPU: AArch64 Processor [411fd071]<\r><\n> [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 48,<\r><\n> [ 0.000000] OF: fdt: - 80000000 , 3f800000<\r><\n> [ 0.000000] OF: fdt: - bfa00000 , 3fe00000<\r><\n> [ 0.000000] OF: fdt: - ffa00000 , 600000<\r><\n> [ 0.000000] Found tegra_fbmem: 00140000@92ca9000<\r><\n> [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '')<\r><\n> [ 0.000000] bootconsole [uart8250] enabled<\r><\n>