áÙ0035.643] I> MB1 (version: 0.32.0.0-t234-54845784-57325615)
[0035.648] I> t234-A01-1-Silicon (0x12347) Prod
[0035.653] I> Boot-mode : BPMP Diagnostic
[0035.656] I> Emulation:
[0035.659] I> Entry timestamp: 0x00000000
[0035.663] I> last_boot_error: 0x27228311
[0035.666] I> BR-BCT: preprod_dev_sign: 0
[0035.670] I> rst_source: 0xb, rst_level: 0x1
[0035.674] I> Task: Initialize MB2 params (0x5000cb51)
[0035.680] I> MB2-params @ 0x40060000
[0035.683] I> Task: Crypto init (0x5001d981)
[0035.687] I> Task: Secure debug controls (0x5000c0a9)
[0035.692] I> Task: strap war set (0x5000ba2d)
[0035.696] I> Task: Program NV master stream id (0x5000c05d)
[0035.702] I> Task: Verify boot mode (0xd4820f1)
[0035.708] I> Task: Alias fuses (0x5001095d)
[0035.712] W> FUSE_ALIAS: Fuse alias on production fused part is not supported.
[0035.719] I> Task: Print SKU type (0x5000f5f1)
[0035.723] I> FUSE_OPT_CCPLEX_CLUSTER_DISABLE = 0x000001c8
[0035.728] I> FUSE_OPT_GPC_DISABLE = 0x00000002
[0035.733] I> FUSE_OPT_TPC_DISABLE = 0x000000fc
[0035.737] I> FUSE_OPT_DLA_DISABLE = 0x00000003
[0035.741] I> FUSE_OPT_PVA_DISABLE = 0x00000001
[0035.746] I> FUSE_OPT_NVENC_DISABLE = 0x00000001
[0035.750] I> FUSE_OPT_NVDEC_DISABLE = 0x00000000
[0035.754] I> FUSE_OPT_FSI_DISABLE = 0x00000001
[0035.759] I> FUSE_OPT_EMC_DISABLE = 0x0000000c
[0035.763] I> FUSE_BOOTROM_PATCH_VERSION = 0x7
[0035.767] I> FUSE_PSCROM_PATCH_VERSION = 0x7
[0035.771] I> FUSE_OPT_ADC_CAL_FUSE_REV = 0x2
[0035.775] I> FUSE_SKU_INFO_0 = 0xd6
[0035.779] I> FUSE_OPT_SAMPLE_TYPE_0 = 0x3 PS
[0035.783] I> FUSE_PACKAGE_INFO_0 = 0x2
[0035.786] I> SKU: Prod
[0035.789] I> Task: Boost clocks (0x500148a1)
[0035.793] I> Initializing PLLC2 for AXI_CBB.
[0035.797] I> AXI_CBB : src = 35, divisor = 0
[0035.801] I> Task: Voltage monitor (0x50014b49)
[0035.805] I> VMON: Vmon re-calibration and fine tuning done
[0035.811] I> Task: UPHY init (0x5000d065)
[0035.815] W> UPHY: UPHY lane info table is empty in MB1 BCT.
[0035.820] I> Task: Boot device init (0x50000be9)
[0035.825] I> Boot_device: RCM
[0035.828] I> USB configuration success
[0035.832] I> Task: TSC init (0x50020a4d)
[0035.836] I> Task: Enable WDT 5th expiry (0x50021a41)
[0035.841] I> Task: I2C register (0x50000b85)
[0035.845] I> Task: Reset FSI (0x500148b1)
[0035.849] I> Task: Enable clock-mon (0x50020a35)
[0035.854] I> FMON: Fmon re-programming done
[0035.858] I> Task: MB1 fixed firewalls (0x5002006d)
[0035.864] W> Firewall readback mismatch
[0035.868] W> Firewall readback mismatch
[0035.872] W> Firewall readback mismatch
[0035.878] I> Task: Load MB2/Applet/FSKP (0x5000ca55)
[0035.882] I> Loading MB2 Applet
[0035.885] I> Slot: 1
[0035.888] E> BLOCK_DEV: Failed to open blockdev.
[0035.892] E> LOADER: Failed to open blockdev 0(0).
[0035.898] E> LOADER: Failed to get storage info for binary 21 from loader.
[0035.905] C> LOADER: Could not read binary 21.
[0035.909] E> Failed to load MB2
[0035.912] C> Task 0x0 failed (err: 0x27228311)
[0035.917] E> Top caller module: MB2_PARAMS, error module: LOADER, reason: 0x11, aux_info: 0x83
[0035.925] C> Boot Info Table status dump :
1