# dmesg [ 0.000000] Booting Linux on physical CPU 0x100 [ 0.000000] Linux version 4.9.140-tegra (buildbrain@mobile-u64-4255) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Fri Oct 16 12:25:00 PDT 2020 [ 0.000000] Boot CPU: AArch64 Processor [411fd073] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 16416, [ 0.000000] OF: fdt: - 80000000 , 70000000 [ 0.000000] OF: fdt: - f0200000 , 185600000 [ 0.000000] OF: fdt: - 275e00000 , 200000 [ 0.000000] OF: fdt: - 276600000 , 200000 [ 0.000000] OF: fdt: - 277000000 , 200000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000003100000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb2_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb2_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fc000000 [ 0.000000] On node 0 totalpages: 2055168 [ 0.000000] DMA zone: 8192 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 523776 pages, LIFO batch:31 [ 0.000000] Normal zone: 24008 pages used for memmap [ 0.000000] Normal zone: 1531392 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 25 pages/cpu @ffffffc1f676a000 s61656 r8192 d32552 u102400 [ 0.000000] pcpu-alloc: s61656 r8192 d32552 u102400 alloc=25*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2022968 [ 0.000000] Kernel command line: console=ttyS0,115200 androidboot.presilicon=true firmware_class.path=/etc/firmware root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 isolcpus=1-2 video=tegrafb no_console_suspend=1 earlycon=uart8250,mmio32,0x3100000 nvdumper_reserved=0x2772e0000 gpt usbcore.old_scheme_first=1 tegraid=18.1.2.0.0 maxcpus=6 boot.slot_suffix= boot.ratchetvalues=0.2031647.1 bl_prof_dataptr=0x10000@0x275840000 sdhci_tegra.en_boot_part_access=1 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 isolcpus=1-2 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 163840 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 262144 bytes [ 0.000000] early log buf free: 29204(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Memory: 7968884K/8220672K available (15294K kernel code, 2936K rwdata, 6644K rodata, 8576K init, 611K bss, 186252K reserved, 65536K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f70000 ( 15296 KB) [ 0.000000] .rodata : 0xffffff8008f70000 - 0xffffff8009600000 ( 6720 KB) [ 0.000000] .init : 0xffffff8009600000 - 0xffffff8009e60000 ( 8576 KB) [ 0.000000] .data : 0xffffff8009e60000 - 0xffffff800a13e008 ( 2937 KB) [ 0.000000] .bss : 0xffffff800a13e008 - 0xffffff800a1d6f7c ( 612 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf07dc8000 ( 125 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc1f7200000 ( 8050 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=6. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 31.25MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xe6a171046, max_idle_ns: 881590405314 ns [ 0.000003] sched_clock: 56 bits at 31MHz, resolution 32ns, wraps every 4398046511088ns [ 0.001672] Console: colour dummy device 80x25 [ 0.001676] console [tty0] enabled [ 0.001679] bootconsole [uart8250] disabled [ 0.001686] kmemleak: Kernel memory leak detector disabled [ 0.001695] Calibrating delay loop (skipped), value calculated using timer frequency.. 62.50 BogoMIPS (lpj=125000) [ 0.001702] pid_max: default: 32768 minimum: 301 [ 0.002018] Security Framework initialized [ 0.002175] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.002180] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.002789] ftrace: allocating 47119 entries in 185 pages [ 0.127408] sched-energy: Sched-energy-costs installed from DT [ 0.127418] ASID allocator initialised with 65536 entries [ 0.164321] tegra-id: chipid=21817. [ 0.164327] tegra-id: opt_subrevision=1. [ 0.164344] Tegra Revision: A02p SKU: 0xdc CPU Process: 0 SoC Process: 0 [ 0.164352] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t18x/quill/kernel-dts/tegra186-quill-p3310-1000-c03-00-base.dts [ 0.164357] DTB Build time: Oct 16 2020 12:30:58 [ 0.213690] CPU1: Booted secondary processor [4e0f0030] [ 0.245336] CPU2: Booted secondary processor [4e0f0030] [ 0.277114] CPU3: Booted secondary processor [411fd073] [ 0.309099] CPU4: Booted secondary processor [411fd073] [ 0.341095] CPU5: Booted secondary processor [411fd073] [ 0.341146] Brought up 6 CPUs [ 0.341150] SMP: Total of 6 processors activated. [ 0.341155] CPU features: detected feature: 32-bit EL0 Support [ 0.341856] CPU: All CPU(s) started at EL2 [ 0.341908] alternatives: patching kernel code [ 0.344790] devtmpfs: initialized [ 0.383525] Initilizing CustomIPI irq domain [ 0.383713] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.383721] futex hash table entries: 2048 (order: 5, 131072 bytes) [ 0.384594] pinctrl core: initialized pinctrl subsystem [ 0.384800] OS set in device tree is not L4T. [ 0.384950] regulator-dummy: no parameters [ 0.385082] Initializing plugin-manager [ 0.385148] Plugin module not found [ 0.385186] Plugin-manager status disabled [ 0.386970] NET: Registered protocol family 16 [ 0.387730] pstore: using zlib compression [ 0.387743] console [pstore-1] enabled [ 0.387746] pstore: Registered ramoops as persistent store backend [ 0.387749] ramoops: attached 0x200000@0x275880000, ecc: 0/0 [ 0.401158] cpuidle: using governor menu [ 0.402732] bpmp: waiting for handshake [ 0.402736] bpmp: handshake completed [ 0.402750] bpmp: synchronizing channels [ 0.402767] bpmp: channels synchronized [ 0.402770] bpmp: mail init ok [ 0.404861] arm-smmu 12000000.iommu: probing hardware configuration... [ 0.404866] arm-smmu 12000000.iommu: SMMUv2 with: [ 0.404870] arm-smmu 12000000.iommu: stage 1 translation [ 0.404873] arm-smmu 12000000.iommu: stage 2 translation [ 0.404876] arm-smmu 12000000.iommu: nested translation [ 0.404882] arm-smmu 12000000.iommu: stream matching with 128 register groups, mask 0x7f80 [ 0.404888] arm-smmu 12000000.iommu: SMMU address space size (0x800000) differs from mapped region size (0x1000000)! [ 0.404892] arm-smmu 12000000.iommu: 64 context banks (0 stage-2 only) [ 0.404896] arm-smmu 12000000.iommu: Stage-1: 39-bit VA -> 48-bit IPA [ 0.404899] arm-smmu 12000000.iommu: Stage-2: 39-bit IPA -> 48-bit PA [ 0.407127] vdso: 2 pages (1 code @ ffffff8008f77000, 1 data @ ffffff8009e64000) [ 0.407140] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.409314] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations [ 0.411475] Registering BPMP clocks... [ 0.411559] tegra_bpmp_clk_init: clock init ok (638 clks) [ 0.412514] Serial: AMBA PL011 UART driver [ 0.413640] tegra_powergate_init: DONE [ 0.413648] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t18x/quill/kernel-dts/tegra186-quill-p3310-1000-c03-00-base.dts [ 0.413654] DTB Build time: Oct 16 2020 12:30:58 [ 0.415799] Tegra reboot handler registered. [ 0.417377] tegra-pmc c360000.pmc: scratch reg offset dts data not present [ 0.417446] tegra-pmc: get_secure_pmc_setting: done secure_pmc=0 [ 0.417459] tegra-pmc: ### PMC reset source: TEGRA_SOFTWARE_RESET [ 0.417461] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_L1 [ 0.417464] tegra-pmc: ### PMC reset status reg: 0x2d [ 0.417622] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [ 0.417633] tegra-pmc c360000.pmc: IO padctrl driver initialized [ 0.417964] iommu: Adding device 3460000.sdhci to group 0 [ 0.418646] iommu: Adding device 3400000.sdhci to group 1 [ 0.419688] iommu: Adding device 3507000.ahci-sata to group 2 [ 0.419701] arm-smmu: forcing sodev map for 3507000.ahci-sata [ 0.420148] iommu: Adding device 3160000.i2c to group 3 [ 0.420581] iommu: Adding device c240000.i2c to group 4 [ 0.420990] iommu: Adding device 3180000.i2c to group 5 [ 0.421350] iommu: Adding device 3190000.i2c to group 6 [ 0.421770] iommu: Adding device 31b0000.i2c to group 7 [ 0.422111] iommu: Adding device 31c0000.i2c to group 8 [ 0.422446] iommu: Adding device c250000.i2c to group 9 [ 0.422775] iommu: Adding device 31e0000.i2c to group 10 [ 0.424288] iommu: Adding device 3210000.spi to group 11 [ 0.424634] iommu: Adding device c260000.spi to group 12 [ 0.425020] iommu: Adding device 3240000.spi to group 13 [ 0.425717] iommu: Adding device 3100000.serial to group 14 [ 0.426058] iommu: Adding device 3110000.serial to group 15 [ 0.426394] iommu: Adding device c280000.serial to group 16 [ 0.426732] iommu: Adding device 3130000.serial to group 17 [ 0.428096] iommu: Adding device 2490000.ether_qos to group 18 [ 0.428109] arm-smmu: forcing sodev map for 2490000.ether_qos [ 0.428837] iommu: Adding device b000000.rtcpu to group 19 [ 0.431067] iommu: Adding device 13e10000.host1x to group 20 [ 0.431373] iommu: Adding device 13e10000.host1x:ctx0 to group 21 [ 0.431674] iommu: Adding device 13e10000.host1x:ctx1 to group 22 [ 0.431986] iommu: Adding device 13e10000.host1x:ctx2 to group 23 [ 0.432287] iommu: Adding device 13e10000.host1x:ctx3 to group 24 [ 0.432585] iommu: Adding device 13e10000.host1x:ctx4 to group 25 [ 0.432929] iommu: Adding device 13e10000.host1x:ctx5 to group 26 [ 0.433239] iommu: Adding device 13e10000.host1x:ctx6 to group 27 [ 0.433546] iommu: Adding device 13e10000.host1x:ctx7 to group 28 [ 0.434012] iommu: Adding device 150c0000.nvcsi to group 29 [ 0.434660] iommu: Adding device 15700000.vi to group 30 [ 0.435018] iommu: Adding device 15600000.isp to group 31 [ 0.435482] iommu: Adding device 15210000.nvdisplay to group 32 [ 0.436098] iommu: Adding device 15340000.vic to group 33 [ 0.436317] iommu: Adding device 154c0000.nvenc to group 34 [ 0.436535] iommu: Adding device 15480000.nvdec to group 35 [ 0.436928] iommu: Adding device 15380000.nvjpg to group 36 [ 0.437151] iommu: Adding device 15500000.tsec to group 37 [ 0.437379] iommu: Adding device 15100000.tsecb to group 38 [ 0.438063] iommu: Adding device 15810000.se to group 39 [ 0.438283] iommu: Adding device 15820000.se to group 40 [ 0.438495] iommu: Adding device 15830000.se to group 41 [ 0.438709] iommu: Adding device 15840000.se to group 42 [ 0.439608] iommu: Adding device smmu_test to group 43 [ 0.440210] mc: mapped MMIO address: 0xffffff800a6c0000 -> 0x2c10000 [ 0.440221] mc: mapped MMIO address: 0xffffff800a6e0000 -> 0x2c20000 [ 0.440231] mc: mapped MMIO address: 0xffffff800a7b0000 -> 0x2c30000 [ 0.440241] mc: mapped MMIO address: 0xffffff800a7d0000 -> 0x2c40000 [ 0.440251] mc: mapped MMIO address: 0xffffff800b110000 -> 0x2c50000 [ 0.440260] nv-tegra-mc 2c10000.mc: No mssnvlink node [ 0.440269] mc-err: mcerr ops are set to t18x [ 0.440411] dram-ecc: DRAM ECC disabled-MC_ECC_CONTROL:0x0000000c [ 0.441703] iommu: Adding device 3530000.xhci to group 44 [ 0.441715] arm-smmu: forcing sodev map for 3530000.xhci [ 0.442180] iommu: Adding device 3550000.xudc to group 45 [ 0.442191] arm-smmu: forcing sodev map for 3550000.xudc [ 0.442897] tegra186-aowake c370000.pmc: WAKE_AOWAKE_CTRL_0 = 3 [ 0.442903] tegra186-aowake c370000.pmc: WAKE_AOWAKE_CNTRL_24(PMU_INT) = 256 [ 0.443475] iommu: Adding device 17000000.gp10b to group 46 [ 0.444521] tegra-reset 5000000.clock: registered 193 resets. [ 0.446751] iommu: Adding device d000000.bpmp to group 47 [ 0.446957] bpmp: ping status is 0 [ 0.447056] bpmp d000000.bpmp: firmware tag is 4208eb5c85fe47a2235fbc0b8eb87dca [ 0.449563] bpmp d000000.bpmp: probe ok [ 0.452723] iommu: Adding device 2600000.dma to group 48 [ 0.454008] GPIO line 461 (camera-control-output-low) hogged as output/low [ 0.454038] GPIO line 456 (camera-control-output-low) hogged as output/low [ 0.454067] GPIO line 457 (camera-control-output-low) hogged as output/low [ 0.454094] GPIO line 426 (camera-control-output-low) hogged as output/low [ 0.454124] GPIO line 424 (wifi-enable) hogged as output/high [ 0.454152] GPIO line 445 (sdmmc-wake-support-input) hogged as input [ 0.454180] GPIO line 446 (sdmmc-wake-support-output) hogged as output/low [ 0.454342] gpiochip_setup_dev: registered GPIOs 320 to 511 on device: gpiochip0 (tegra-gpio) [ 0.458102] GPIO line 315 (wifi-wake-ap) hogged as input [ 0.458238] gpiochip_setup_dev: registered GPIOs 256 to 319 on device: gpiochip1 (tegra-gpio-aon) [ 0.459822] iommu: Adding device 10003000.pcie-controller to group 49 [ 0.459836] arm-smmu: forcing sodev map for 10003000.pcie-controller [ 0.460159] iommu: Adding device sound to group 50 [ 0.460536] iommu: Adding device 3510000.hda to group 51 [ 0.468072] iommu: Adding device c1a0000.aon to group 52 [ 0.468503] vdd-ac-bat: 5000 mV [ 0.470228] vdd-1v8-ap: 1800 mV [ 0.497566] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.500293] eventlib_kernel: keventlib is initialized, test id: 0 [ 0.500486] SCSI subsystem initialized [ 0.500598] libata version 3.00 loaded. [ 0.500745] usbcore: registered new interface driver usbfs [ 0.500777] usbcore: registered new interface driver hub [ 0.500836] usbcore: registered new device driver usb [ 0.501343] random: fast init done [ 0.504103] GPIO line 241 (touch-rails) hogged as output/high [ 0.504512] GPIO line 242 (touch-rails) hogged as output/high [ 0.504673] gpiochip_setup_dev: registered GPIOs 240 to 255 on device: gpiochip2 (tca9539) [ 0.505008] tegra-i2c 3160000.i2c: no acknowledge from address 0x77 [ 0.505039] pca953x 0-0077: failed reading register [ 0.505090] pca953x: probe of 0-0077 failed with error -121 [ 0.514774] max77620 4-003c: PMIC Version OTP:0x45 and ES:0x8 [ 0.521274] vddio-ddr: at 1125 mV [ 0.525114] avdd_dsi_csi: 1200 mV [ 0.529114] vdd-1v8: 1800 mV [ 0.533113] vdd-3v3-sys: 3300 mV [ 0.534225] spmic-ldo0: at 1800 mV [ 0.534926] spmic-ldo1: at 800 mV [ 0.537113] vddio-3v3: 3300 mV [ 0.537839] vddio-sdmmc1: 1800 <--> 3300 mV at 3300 mV [ 0.541114] vdd-rtc: at 800 mV [ 0.541842] avdd-ts-hv: 1800 <--> 3300 mV at 1800 mV [ 0.545114] spmic-ldo6: at 1500 mV [ 0.549113] vdd-pex-1v00: 1000 mV [ 0.549737] dvdd-pex: 1000 mV [ 0.551932] GPIO line 237 (spmic_gpio_input) hogged as input [ 0.552084] GPIO line 238 (spmic_gpio_input) hogged as input [ 0.552232] gpiochip_setup_dev: registered GPIOs 232 to 239 on device: gpiochip3 (max77620-gpio) [ 0.552400] max77620 4-003c: max77620 probe successful [ 0.552774] media: Linux media interface: v0.10 [ 0.552803] Linux video capture interface: v2.00 [ 0.556426] pps_core: LinuxPPS API ver. 1 registered [ 0.556429] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.556443] PTP clock support registered [ 0.556630] tegra_wdt_t18x 30c0000.watchdog: Expiry count is deprecated [ 0.556820] tegra_wdt_t18x 30c0000.watchdog: Tegra WDT init timeout = 120 sec [ 0.556835] tegra_wdt_t18x 30c0000.watchdog: Registered successfully [ 0.558206] trusty trusty: trusty version: Built: 12:18:15 Oct 16 2020 [ 0.558220] trusty trusty: selected api version: 3 (requested 3) [ 0.559268] Advanced Linux Sound Architecture Driver Initialized. [ 0.559717] Bluetooth: Core ver 2.22 [ 0.559778] NET: Registered protocol family 31 [ 0.559780] Bluetooth: HCI device and connection manager initialized [ 0.559788] Bluetooth: HCI socket layer initialized [ 0.559792] Bluetooth: L2CAP socket layer initialized [ 0.559806] Bluetooth: SCO socket layer initialized [ 0.560544] en-vdd-sd: 3300 mV [ 0.565115] vdd-hdmi: 5000 mV [ 0.565404] vdd-usb0-5v: 5000 mV [ 0.565679] vdd-usb1-5v: 5000 mV [ 0.569114] en-vdd-ts-1v8: 1800 mV [ 0.573114] en-vdd-ts-hv-3v3: 3300 mV [ 0.573769] en-vdd-disp-3v3: 3300 mV [ 0.574422] en-mdm-pwr-3v7: 3700 mV [ 0.575074] en-vdd-disp-1v8: 1800 mV [ 0.575757] en-vdd-cam-hv-2v8: 2800 mV [ 0.576484] vdd-fan: 5000 mV [ 0.576742] vdd-3v3: 3300 mV [ 0.577674] dis-vdd-1v2: 1200 mV [ 0.577948] en-vdd-vcm-2v8: 2800 mV [ 0.578649] vdd-usb2-5v: 5000 mV [ 0.578920] vdd-sys-bl: 3300 mV [ 0.581309] camchar: rtcpu character device driver loaded [ 0.581947] gpio tegra-gpio wake53 for gpio=159(X:7) [ 0.583658] extcon-gpio-states external-connection:extcon@1: Cable state:1, cable id:1 [ 0.584575] clocksource: Switched to clocksource arch_sys_counter [ 0.606328] VFS: Disk quotas dquot_6.6.0 [ 0.606401] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.606634] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.607146] nvmap: nvmap_select_cache_ops() nvmap cache ops set to roc [ 0.607152] nvmap_page_pool_init: Total RAM pages: 2008605 [ 0.607155] nvmap_page_pool_init: nvmap page pool size: 251075 pages (980 MB) [ 0.607224] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.609959] tegra-gpcdma 2600000.dma: GPC DMA driver register 32 channels [ 0.615703] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type BCPU-therm [ 0.615866] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type MCPU-therm [ 0.616246] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm [ 0.616322] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [ 0.616424] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type Tboard_tegra [ 0.616521] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type Tdiode_tegra [ 0.616700] thermal thermal_zone6: Registering thermal zone thermal_zone6 for type PMIC-Die [ 0.616894] la/ptsa driver initialized. [ 0.616903] pre_t19x_iso_plat_init(): iso emc max clk=1866000KHz [ 0.616906] pre_t19x_iso_plat_init(): max_iso_bw=26870400KB [ 0.617198] NET: Registered protocol family 2 [ 0.617783] TCP established hash table entries: 65536 (order: 7, 524288 bytes) [ 0.618087] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.618677] TCP: Hash tables configured (established 65536 bind 65536) [ 0.618726] UDP hash table entries: 4096 (order: 5, 131072 bytes) [ 0.618840] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes) [ 0.619166] NET: Registered protocol family 1 [ 0.619581] RPC: Registered named UNIX socket transport module. [ 0.619585] RPC: Registered udp transport module. [ 0.619587] RPC: Registered tcp transport module. [ 0.619590] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.619596] PCI: CLS 0 bytes, default 64 [ 0.619706] Trying to unpack rootfs image as initramfs... [ 0.784720] Freeing initrd memory: 5432K [ 0.800486] host1x 13e10000.host1x: initialized [ 0.801741] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.803806] audit: initializing netlink subsys (disabled) [ 0.803833] audit: type=2000 audit(0.692:1): initialized [ 0.804260] workingset: timestamp_bits=46 max_order=21 bucket_order=0 [ 0.810740] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.811702] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.812201] 9p: Installing v9fs 9p2000 file system support [ 0.814314] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240) [ 0.814390] io scheduler noop registered [ 0.814593] io scheduler cfq registered (default) [ 0.817808] gic 2a41000.agic-controller: GIC IRQ controller registered [ 0.922726] iommu: Adding device aconnect@2a41000:adsp_audio to group 53 [ 0.957316] iommu: Adding device 2993000.adsp to group 54 [ 0.958359] tegra-aconnect aconnect@2a41000: Tegra ACONNECT bus registered [ 0.960698] tegra-xusb-padctl 3520000.xusb_padctl: VBUS over-current detection enabled [ 0.964276] tegra-pwm 3280000.pwm: PWM clk can sleep in ops [ 0.965434] tegra-pwm 3290000.pwm: PWM clk can sleep in ops [ 0.966490] tegra-pwm 32a0000.pwm: PWM clk can sleep in ops [ 0.967550] tegra-pwm c340000.pwm: PWM clk can sleep in ops [ 0.969875] tegra-pcie 10003000.pcie-controller: 4x1, 1x1 configuration [ 0.970861] tegra-pcie 10003000.pcie-controller: PCIE: Enable power rails [ 0.971212] tegra-pcie 10003000.pcie-controller: probing port 0, using 4 lanes [ 0.971246] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [ 0.971352] misc tegra_camera_ctrl: tegra_camera_isomgr_register tpg_max_iso = 3916800KBs [ 0.971358] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=4687500, vi_iso_bw=2000000, max_bw=4687500 [ 0.973627] tegra-pcie 10003000.pcie-controller: probing port 2, using 1 lanes [ 0.974910] tsec 15500000.tsec: initialized [ 0.975980] tsec 15100000.tsecb: initialized [ 0.979458] nvdec 15480000.nvdec: initialized [ 0.985833] falcon 15340000.vic: initialized [ 0.987166] falcon 154c0000.nvenc: initialized [ 0.988370] falcon 15380000.nvjpg: initialized [ 0.990334] iommu_context_dev 13e10000.host1x:ctx0: initialized (streamid=56) [ 0.991690] iommu_context_dev 13e10000.host1x:ctx1: initialized (streamid=57) [ 0.993057] iommu_context_dev 13e10000.host1x:ctx2: initialized (streamid=58) [ 0.994352] iommu_context_dev 13e10000.host1x:ctx3: initialized (streamid=59) [ 0.995649] iommu_context_dev 13e10000.host1x:ctx4: initialized (streamid=60) [ 0.996978] iommu_context_dev 13e10000.host1x:ctx5: initialized (streamid=61) [ 0.998306] iommu_context_dev 13e10000.host1x:ctx6: initialized (streamid=62) [ 0.999618] iommu_context_dev 13e10000.host1x:ctx7: initialized (streamid=63) [ 1.002973] tegradccommon 15200000.dc_common: host1x channel mapped [ 1.002981] tegradccommon 15200000.dc_common: dc_common syncpt # 1 allocated [ 1.003016] tegradccommon 15200000.dc_common: dma mapping done [ 1.003200] tegra_cec 3960000.tegra_cec: dt=1 start=0x03960000 end=0x03960FFF irq=390 [ 1.003476] tegradc 15210000.nvdisplay: disp0 connected to head1->/host1x/sor1 [ 1.003519] generic_infoframe_type: 0x87 [ 1.003596] tegradc 15210000.nvdisplay: DT parsed successfully [ 1.003615] tegradc 15210000.nvdisplay: Display dc.ffffff800b650000 registered with id=0 [ 1.003878] tegra_cec 3960000.tegra_cec: Unpowergate DISP: 0. [ 1.004747] tegra_cec 3960000.tegra_cec: Enable clock result: 0. [ 1.004833] tegra_cec 3960000.tegra_cec: tegra_cec_init started [ 1.004896] tegra_cec 3960000.tegra_cec: cec_add_sysfs ret=0 [ 1.004900] tegra_cec 3960000.tegra_cec: probed [ 1.008977] tegra_nvdisp_bandwidth_register_max_config: max config iso bw = 16727000 KB/s [ 1.008981] tegra_nvdisp_bandwidth_register_max_config: max config EMC floor = 665600000 Hz [ 1.008983] tegra_nvdisp_bandwidth_register_max_config: max config hubclk = 357620000 Hz [ 1.009153] tegradc 15210000.nvdisplay: vblank syncpt # 8 for dc 1 [ 1.009158] tegradc 15210000.nvdisplay: vpulse3 syncpt # 9 for dc 1 [ 1.015339] tegradc 15210000.nvdisplay: hdmi: invalid prod list prod_list_hdmi_board [ 1.015344] tegradc 15210000.nvdisplay: hdmi: tegra_hdmi_tmds_range_read(bd) failed [ 1.018020] tegradc 15210000.nvdisplay: probed [ 1.018361] Console: switching to colour frame buffer device 80x30 [ 1.018382] tegradc 15210000.nvdisplay: fb registered [ 1.018530] gpio tegra-gpio wake21 for gpio=121(P:1) [ 1.021483] tegra-adma 2930000.adma: Tegra210 ADMA driver registered 32 channels [ 1.022199] tegra-fuse-burn 3820000.efuse:efuse-burn: shutdown limit check disabled [ 1.022224] tegra-fuse-burn 3820000.efuse:efuse-burn: Fuse burn driver initialized [ 1.022664] kfuse 3830000.kfuse: initialized [ 1.024004] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0 [ 1.026735] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.029072] console [ttyS0] disabled [ 1.029107] 3100000.serial: ttyS0 at MMIO 0x3100000 (irq = 36, base_baud = 25500000) is a Tegra [ 1.034029] console [ttyS0] enabled [ 1.035380] 3110000.serial: ttyTHS1 at MMIO 0x3110000 (irq = 37, base_baud = 0) is a TEGRA_UART [ 1.036227] c280000.serial: ttyTHS2 at MMIO 0xc280000 (irq = 38, base_baud = 0) is a TEGRA_UART [ 1.036396] serial-tegra 3130000.serial: RX in PIO mode [ 1.037179] 3130000.serial: ttyTHS3 at MMIO 0x3130000 (irq = 39, base_baud = 0) is a TEGRA_UART [ 1.038175] [drm] Initialized [ 1.044961] brd: module loaded [ 1.048303] loop: module loaded [ 1.048364] tegra_profiler: version: 1.141, samples/io: 48/28 [ 1.048438] tegra_profiler: auth: init [ 1.048781] nct1008_nct72 7-004c: starting parse dt [ 1.048877] nct1008_nct72 7-004c: !!!Found deprecated property!!! [ 1.048882] nct1008_nct72 7-004c: success parsing dt [ 1.048991] nct1008_nct72 7-004c: success in enabling tmp451 VDD rail [ 1.049321] THERMAL EST: found 3 subdevs [ 1.049325] THERMAL EST num_resources: 0 [ 1.049328] [THERMAL EST subdev 0] [ 1.049333] [THERMAL EST subdev 1] [ 1.049336] [THERMAL EST subdev 2] [ 1.049588] thermal thermal_zone7: Registering thermal zone thermal_zone7 for type thermal-fan-est [ 1.049590] THERMAL EST: thz register success. [ 1.049663] THERMAL EST: end of probe, return err: 0 [ 1.050293] sd: No Scsi addr parsed to reserve index [ 1.050314] hisi_sas: driver version v1.6 [ 1.053794] tegra-ahci 3507000.ahci-sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 1.053801] tegra-ahci 3507000.ahci-sata: flags: 64bit ncq sntf pm led pmp pio slum part deso sadm apst [ 1.054495] scsi host0: tegra_ahci [ 1.054865] scsi host1: tegra_ahci [ 1.054996] ata1: SATA max UDMA/133 mmio [mem 0x03507000-0x03508fff] port 0x100 irq 24 [ 1.055000] ata2: DUMMY [ 1.060093] libphy: Fixed MDIO Bus: probed [ 1.060953] tun: Universal TUN/TAP device driver, 1.6 [ 1.060957] tun: (C) 1999-2004 Max Krasnyansky [ 1.061610] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.061612] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.061643] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.061645] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.061676] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 1.061678] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.061712] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4 [ 1.061714] Copyright(c) 1999 - 2017 Intel Corporation. [ 1.068662] eqos 2490000.ether_qos: can't get pllrefe_vcoout clk (-2) [ 1.071466] eqos 2490000.ether_qos: Setting local MAC: 0 4 4b 8d 80 d5 [ 1.071559] libphy: dwc_phy: probed [ 1.071836] bcm54xx_low_power_mode(): put phy in iddq-lp mode [ 1.073763] PPP generic driver version 2.4.2 [ 1.073873] PPP BSD Compression module registered [ 1.073876] PPP Deflate Compression module registered [ 1.073893] PPP MPPE Compression module registered [ 1.073896] NET: Registered protocol family 24 [ 1.073934] usbcore: registered new interface driver r8152 [ 1.073962] usbcore: registered new interface driver asix [ 1.073989] usbcore: registered new interface driver ax88179_178a [ 1.074014] usbcore: registered new interface driver cdc_ether [ 1.074041] usbcore: registered new interface driver net1080 [ 1.074066] usbcore: registered new interface driver cdc_subset [ 1.074090] usbcore: registered new interface driver zaurus [ 1.074132] usbcore: registered new interface driver cdc_ncm [ 1.074229] VFIO - User Level meta-driver version: 0.3 [ 1.075030] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.075041] ehci-pci: EHCI PCI platform driver [ 1.075069] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.075075] ohci-pci: OHCI PCI platform driver [ 1.075103] ohci-platform: OHCI generic platform driver [ 1.079951] tegra-xusb 3530000.xhci: USB2 port 0 has OTG_CAP [ 1.080729] nct1008_nct72 7-004c: LOC shutdown limit 107 [ 1.081226] nct1008_nct72 7-004c: EXT shutdown limit 107 [ 1.081721] tegra-xusb 3530000.xhci: extcon 0: ffffffc1ead60800 id [ 1.082404] usbcore: registered new interface driver uas [ 1.082442] usbcore: registered new interface driver usb-storage [ 1.082503] usbcore: registered new interface driver usbserial [ 1.084059] tegra-xusb 3530000.xhci: Firmware timestamp: 2019-10-31 05:52:15 UTC, Version: 55.17 release [ 1.086954] tegra-xudc-new 3550000.xudc: device count: 1 [ 1.087902] tegra-xudc-new 3550000.xudc: vbus state: 1 [ 1.109022] tegra-xusb 3530000.xhci: xHCI Host Controller [ 1.109039] tegra-xusb 3530000.xhci: new USB bus registered, assigned bus number 1 [ 1.109741] tegra-xusb 3530000.xhci: hcc params 0x0184fd25 hci version 0x100 quirks 0x00050810 [ 1.109769] tegra-xusb 3530000.xhci: irq 70, io mem 0x03530000 [ 1.109906] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.109911] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.109916] usb usb1: Product: xHCI Host Controller [ 1.109919] usb usb1: Manufacturer: Linux 4.9.140-tegra xhci-hcd [ 1.109922] usb usb1: SerialNumber: 3530000.xhci [ 1.110245] hub 1-0:1.0: USB hub found [ 1.110273] hub 1-0:1.0: 4 ports detected [ 1.110598] tegra-xusb 3530000.xhci: xHCI Host Controller [ 1.110607] tegra-xusb 3530000.xhci: new USB bus registered, assigned bus number 2 [ 1.110734] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.110738] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.110742] usb usb2: Product: xHCI Host Controller [ 1.110745] usb usb2: Manufacturer: Linux 4.9.140-tegra xhci-hcd [ 1.110749] usb usb2: SerialNumber: 3530000.xhci [ 1.111025] hub 2-0:1.0: USB hub found [ 1.111053] hub 2-0:1.0: 3 ports detected [ 1.113952] nct1008_nct72 7-004c: initial LOC temp: 39000 [ 1.114256] nct1008_nct72 7-004c: initial EXT temp: 52250 [ 1.114858] nct1008_nct72 7-004c: hi_b:-11, lo_b:0 [ 1.115149] gpio tegra-gpio-aon wake35 for gpio=16(V:0) [ 1.115328] nct1008_nct72 7-004c: nct1008_probe: initialized [ 1.212701] usb usb1: usb_suspend_both: status 0 [ 1.260789] tegra-usb-cd usb_cd: notification status (0x0, 0x1) [ 1.260793] tegra-usb-cd usb_cd: connected to SDP [ 1.260803] tegra-xudc-new 3550000.xudc: device mode on: 0 [ 1.260958] tegra-xudc-new 3550000.xudc: active: 0 => 1 [ 1.261439] mousedev: PS/2 mouse device common for all mice [ 1.261494] usbcore: registered new interface driver xpad [ 1.378265] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 1.379353] Wake73 for irq=42 [ 1.380649] rtc rtc1: alarm rtc device [ 1.380660] tegra_rtc c2a0000.rtc: rtc core: registered c2a0000.rtc as rtc1 [ 1.380674] tegra_rtc c2a0000.rtc: Tegra internal Real Time Clock [ 1.380879] i2c /dev entries driver [ 1.382702] max77620-power max77620-power: Event recorder REG_NVERC : 0x0 [ 1.387592] parse_throttle_dt_data: Num cap clks = 4 [ 1.387597] parse_throttle_dt_data: clk=mcpu type=1 [ 1.387600] parse_throttle_dt_data: clk=bcpu type=2 [ 1.387607] parse_throttle_dt_data: clk=gpu type=4 [ 1.387609] parse_throttle_dt_data: clk=emc type=3 [ 1.388604] tegra_throttle_probe: probe successful. #cdevs=4 [ 1.389173] FAN dev name: pwm-fan [ 1.389235] FAN:gpio request success. [ 1.389244] FAN: can't find tach_gpio [ 1.389267] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255 [ 1.389453] pwm_fan_driver pwm-fan: got pwm for fan. polarity is inversed [ 1.389458] pwm_fan_driver pwm-fan: tach period: 1000 [ 1.390028] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2 [ 1.390032] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2 [ 1.390036] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2 [ 1.390040] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2 [ 1.390044] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3 [ 1.390048] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3 [ 1.390051] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3 [ 1.390055] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4 [ 1.390059] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4 [ 1.390062] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4 [ 1.390973] device-mapper: uevent: version 1.0.3 [ 1.391290] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 1.391543] CPU EMC frequency mapping table: from device tree [ 1.397932] cpufreq: platform driver Initialization: pass [ 1.398518] cpuidle: Initializing cpuidle driver init for Denver cluster [ 1.398633] cpuidle: Initializing cpuidle driver init for A57 cluster [ 1.399433] sdhci: Secure Digital Host Controller Interface driver [ 1.399435] sdhci: Copyright(c) Pierre Ossman [ 1.399436] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.400698] sdhci-tegra 3460000.sdhci: Client registration for eMC Successful [ 1.402443] CMDQ: cmdq_platfm_init successful [ 1.403181] sdhci-tegra 3440000.sdhci: Client registration for eMC Successful [ 1.403960] CQE: CMD_TIMING bit set for R1B DCMD [ 1.405323] sdhci-tegra 3400000.sdhci: Got CD GPIO [ 1.405374] sdhci-tegra 3400000.sdhci: Got WP GPIO [ 1.408332] sdhci-tegra 3400000.sdhci: Client registration for eMC Successful [ 1.410055] sdhci-tegra 3400000.sdhci: wakeup init done, cdirq 257 [ 1.410601] tegra-pcie 10003000.pcie-controller: link 2 down, retrying [ 1.414476] tegra-se-elp 3ad0000.se_elp: tegra_se_elp_probe: complete [ 1.415364] tegra-se-nvhost 15810000.se: initialized [ 1.416432] tegra-se-nvhost 15810000.se: tegra_se_probe: complete [ 1.417082] tegra-se-nvhost 15820000.se: initialized [ 1.417987] tegra-se-nvhost 15820000.se: tegra_se_probe: complete [ 1.418550] tegra-se-nvhost 15830000.se: initialized [ 1.419299] tegra-se-nvhost 15830000.se: tegra_se_probe: complete [ 1.419845] tegra-se-nvhost 15840000.se: initialized [ 1.420734] tegra-se-nvhost 15840000.se: tegra_se_probe: complete [ 1.420975] hidraw: raw HID events driver (C) Jiri Kosina [ 1.422681] usbcore: registered new interface driver usbhid [ 1.422684] usbhid: USB HID core driver [ 1.424390] tegra-i2c 3160000.i2c: no acknowledge from address 0x42 [ 1.424419] ina3221x 0-0042: ina3221 reset failure status: 0xffffff87 [ 1.430986] ina3221x: probe of 0-0042 failed with error -121 [ 1.434328] tegra186-cam-rtcpu b000000.rtcpu: Trace buffer configured at IOVA=0xbff00000 [ 1.436518] tegra-ivc ivc-b000000.rtcpu: region 0: iova=0xbfef0000-0xbfefdb7f size=56192 [ 1.436857] tegra-ivc ivc-b000000.rtcpu:echo@0: echo: ver=0 grp=1 RX[16x64]=0x1000-0x1480 TX[16x64]=0x1480-0x1900 [ 1.436975] tegra-ivc ivc-b000000.rtcpu:i2c@480: i2c: ver=0 grp=1 RX[8x128]=0x1900-0x1d80 TX[8x128]=0x1d80-0x2200 [ 1.437164] tegra-ivc ivc-b000000.rtcpu:vinotify@12c0: vinotify: ver=0 grp=1 RX[64x128]=0x2200-0x4280 TX[64x128]=0x4280-0x6300 [ 1.437833] tegra-ivc ivc-b000000.rtcpu:mods@32c0: mods: ver=0 grp=1 RX[1x64]=0x6300-0x63c0 TX[1x64]=0x63c0-0x6480 [ 1.437902] tegra-ivc ivc-b000000.rtcpu:ivccontrol@52c0: ivccontrol: ver=0 grp=1 RX[16x320]=0x6480-0x7900 TX[16x320]=0x7900-0x8d80 [ 1.437953] tegra-ivc ivc-b000000.rtcpu:ivccapture@72c0: ivccapture: ver=0 grp=1 RX[16x64]=0x8d80-0x9200 TX[16x64]=0x9200-0x9680 [ 1.438002] tegra-ivc ivc-b000000.rtcpu:dbg@7c00: dbg: ver=0 grp=1 RX[1x384]=0x9680-0x9880 TX[1x384]=0x9880-0x9a80 [ 1.438098] tegra-ivc ivc-b000000.rtcpu:dbg@7e00: dbg: ver=0 grp=1 RX[1x8192]=0x9a80-0xbb00 TX[1x8192]=0xbb00-0xdb80 [ 1.438412] tegra186-cam-rtcpu b000000.rtcpu: using cam RTCPU IRQ (51) [ 1.438415] tegra186-cam-rtcpu b000000.rtcpu: tegra_camrtc_mon_create is successful [ 1.438940] tegra186-cam-rtcpu b000000.rtcpu: firmware version cpu=sce cmd=5 sha1=3ecb1dca25fa98771f988f238c025334776c9a96 [ 1.440531] tegra_aon c1a0000.aon: tegra aon driver probe OK [ 1.441024] tegra186-aondbg aondbg: aondbg driver probe() OK [ 1.441188] register_ari_mca_banks: Registered MCA ROC:IOB [ 1.441254] register_ari_mca_banks: Registered MCA ROC:CCE [ 1.441565] tegra18-bridge 2390000.axi2apb: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 1.441568] tegra18-bridge 2390000.axi2apb: enabled timeout = 11155000 [ 1.441571] tegra18-bridge 2390000.axi2apb: bridge probed OK [ 1.441620] tegra18-bridge 23a0000.axi2apb: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 1.441622] tegra18-bridge 23a0000.axi2apb: enabled timeout = 11155000 [ 1.441624] tegra18-bridge 23a0000.axi2apb: bridge probed OK [ 1.441672] tegra18-bridge 23b0000.axi2apb: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 1.441674] tegra18-bridge 23b0000.axi2apb: enabled timeout = 11155000 [ 1.441676] tegra18-bridge 23b0000.axi2apb: bridge probed OK [ 1.441723] tegra18-bridge 23c0000.axi2apb: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 1.441725] tegra18-bridge 23c0000.axi2apb: enabled timeout = 11155000 [ 1.441728] tegra18-bridge 23c0000.axi2apb: bridge probed OK [ 1.441776] tegra18-bridge 23d0000.axi2apb: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 1.441778] tegra18-bridge 23d0000.axi2apb: enabled timeout = 11155000 [ 1.441780] tegra18-bridge 23d0000.axi2apb: bridge probed OK [ 1.441829] tegra18-bridge 2100000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 1.441833] tegra18-bridge 2100000.axip2p: enabled timeout = 11155000 [ 1.441835] tegra18-bridge 2100000.axip2p: bridge probed OK [ 1.441882] tegra18-bridge 2110000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 1.441886] tegra18-bridge 2110000.axip2p: enabled timeout = 11155000 [ 1.441888] tegra18-bridge 2110000.axip2p: bridge probed OK [ 1.441938] tegra18-bridge 2120000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 1.441942] tegra18-bridge 2120000.axip2p: enabled timeout = 11155000 [ 1.441944] tegra18-bridge 2120000.axip2p: bridge probed OK [ 1.442000] tegra18-bridge 2130000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 1.442004] tegra18-bridge 2130000.axip2p: enabled timeout = 11155000 [ 1.442006] tegra18-bridge 2130000.axip2p: bridge probed OK [ 1.442055] tegra18-bridge 2140000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 1.442058] tegra18-bridge 2140000.axip2p: enabled timeout = 11155000 [ 1.442060] tegra18-bridge 2140000.axip2p: bridge probed OK [ 1.442108] tegra18-bridge 2150000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 1.442114] tegra18-bridge 2150000.axip2p: enabled timeout = 11155000 [ 1.442116] tegra18-bridge 2150000.axip2p: bridge probed OK [ 1.442164] tegra18-bridge 2160000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 1.442169] tegra18-bridge 2160000.axip2p: enabled timeout = 11155000 [ 1.442171] tegra18-bridge 2160000.axip2p: bridge probed OK [ 1.442220] tegra18-bridge 2170000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 1.442225] tegra18-bridge 2170000.axip2p: enabled timeout = 11155000 [ 1.442227] tegra18-bridge 2170000.axip2p: bridge probed OK [ 1.442274] tegra18-bridge 2180000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 1.442280] tegra18-bridge 2180000.axip2p: enabled timeout = 11155000 [ 1.442281] tegra18-bridge 2180000.axip2p: bridge probed OK [ 1.442328] tegra18-bridge 2190000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 1.442333] tegra18-bridge 2190000.axip2p: enabled timeout = 11155000 [ 1.442335] tegra18-bridge 2190000.axip2p: bridge probed OK [ 1.442391] **** A57 ECC: Enabled [ 1.442394] tegra18_a57_serr_init: on CPU 5 a A57 Core [ 1.442454] tegra18x_actmon d230000.actmon: in actmon_register()... [ 1.442905] tegra18x_actmon d230000.actmon: initialization Completed for the device mc_all [ 1.443345] hw perfevents: enabled with denver15_uncore_pmu PMU driver, 3 counters available [ 1.443498] denver_knobs_init:MTS_VERSION:47926945 [ 1.445515] nvpmodel: initialized successfully [ 1.446390] trusty-virtio trusty:virtio: initializing [ 1.446503] trusty_ipc virtio0: vring0: va(pa) ffffffc1e92ec000(0) qsz 32 notifyid 1 [ 1.446510] trusty_ipc virtio0: vring1: va(pa) ffffffc1e92ee000(0) qsz 32 notifyid 2 [ 1.446574] trusty-virtio trusty:virtio: initializing done [ 1.446682] trusty_ipc virtio0: is online [ 1.448332] usbcore: registered new interface driver snd-usb-audio [ 1.452609] mmc0: SDHCI controller on 3460000.sdhci [3460000.sdhci] using ADMA 64-bit with 64 bit addr [ 1.456184] input: tegra-hda HDMI/DP,pcm=3 as /devices/3510000.hda/sound/card0/input0 [ 1.456323] input: tegra-hda HDMI/DP,pcm=7 as /devices/3510000.hda/sound/card0/input1 [ 1.456812] mmc1: SDHCI controller on 3440000.sdhci [3440000.sdhci] using ADMA 64-bit with 64 bit addr [ 1.456898] gpio tegra-gpio wake71 for gpio=125(P:5) [ 1.456946] mmc2: SDHCI controller on 3400000.sdhci [3400000.sdhci] using ADMA 64-bit with 64 bit addr [ 1.502088] mmc0: mmc_decode_ext_csd: CMDQ supported: depth: 31, cmdq_support: 1 [ 1.515089] mmc0: periodic cache flush enabled [ 1.515097] mmc0: new HS400 Enhanced strobe MMC card at address 0001 [ 1.515576] mmcblk0: mmc0:0001 032G34 29.1 GiB [ 1.516505] OPE platform probe [ 1.516562] OPE platform probe successful [ 1.519808] mmcblk0boot0: mmc0:0001 032G34 partition 1 4.00 MiB [ 1.523963] mmcblk0boot1: mmc0:0001 032G34 partition 2 4.00 MiB [ 1.528113] mmcblk0rpmb: mmc0:0001 032G34 partition 3 4.00 MiB [ 1.532459] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 p29 p30 p31 p32 p33 [ 1.563375] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok [ 1.563453] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok [ 1.563520] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok [ 1.563584] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok [ 1.563648] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok [ 1.563724] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok [ 1.563792] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok [ 1.563857] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok [ 1.563921] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok [ 1.563985] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok [ 1.564055] tegra-asoc: sound: ADMAIF11 <-> ADMAIF11 mapping ok [ 1.564127] tegra-asoc: sound: ADMAIF12 <-> ADMAIF12 mapping ok [ 1.564193] tegra-asoc: sound: ADMAIF13 <-> ADMAIF13 mapping ok [ 1.564263] tegra-asoc: sound: ADMAIF14 <-> ADMAIF14 mapping ok [ 1.564330] tegra-asoc: sound: ADMAIF15 <-> ADMAIF15 mapping ok [ 1.564396] tegra-asoc: sound: ADMAIF16 <-> ADMAIF16 mapping ok [ 1.564467] tegra-asoc: sound: ADMAIF17 <-> ADMAIF17 mapping ok [ 1.564533] tegra-asoc: sound: ADMAIF18 <-> ADMAIF18 mapping ok [ 1.564635] tegra-asoc: sound: ADMAIF19 <-> ADMAIF19 mapping ok [ 1.564704] tegra-asoc: sound: ADMAIF20 <-> ADMAIF20 mapping ok [ 1.598872] u32 classifier [ 1.598876] Actions configured [ 1.598934] Initializing XFRM netlink socket [ 1.599472] NET: Registered protocol family 10 [ 1.600038] NET: Registered protocol family 17 [ 1.600049] NET: Registered protocol family 15 [ 1.600106] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.600143] Bluetooth: RFCOMM socket layer initialized [ 1.600151] Bluetooth: RFCOMM ver 1.11 [ 1.600155] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.600159] Bluetooth: HIDP socket layer initialized [ 1.600172] 9pnet: Installing 9P2000 support [ 1.600212] Key type dns_resolver registered [ 1.600915] Registered cp15_barrier emulation handler [ 1.600932] Registered setend emulation handler [ 1.604348] registered taskstats version 1 [ 1.616669] isp 15600000.isp: initialized [ 1.651367] nvcsi 150c0000.nvcsi: initialized [ 1.653249] tegra-vi4 15700000.vi: using default number of vi channels,15 [ 1.656184] gpio tegra-gpio-aon wake29 for gpio=56(FF:0) [ 1.656266] gpio tegra-gpio-aon wake67 for gpio=57(FF:1) [ 1.656336] gpio tegra-gpio-aon wake68 for gpio=58(FF:2) [ 1.656460] input: gpio-keys as /devices/gpio-keys/input/input2 [ 1.680889] tegra-vi4 15700000.vi: initialized [ 1.686956] tegra-vi4 15700000.vi: ep of_device is not enabled /host1x/vi@15700000/ports/port@0/endpoint. [ 1.686960] tegra-vi4 15700000.vi: ep of_device is not enabled /host1x/vi@15700000/ports/port@1/endpoint. [ 1.689946] tegra_rtc c2a0000.rtc: setting system clock to 2021-11-16 19:41:29 UTC (1637091689) [ 1.691286] mmcblk mmc0:0001: Card claimed for testing. [ 1.703186] mmc1: Applying tuning correction [ 1.703199] mmc1: Tap value after applying correction 61 [ 1.703205] mmc1: hw tuning done ... [ 1.706768] mmc1: new ultra high speed SDR104 SDIO card at address 0001 [ 1.720595] bpmp: mounted debugfs mirror [ 1.721811] bwmgr: missing cdev-type property [ 1.728290] spmic-ldo0: disabling [ 1.728517] spmic-ldo1: disabling [ 1.728659] en-vdd-sd: disabling [ 1.728662] vdd-usb0-5v: disabling [ 1.728664] vdd-usb1-5v: disabling [ 1.728667] en-vdd-disp-3v3: disabling [ 1.728669] en-mdm-pwr-3v7: disabling [ 1.728671] en-vdd-disp-1v8: disabling [ 1.728673] en-vdd-cam-hv-2v8: disabling [ 1.728674] vdd-fan: disabling [ 1.728676] vdd-3v3: disabling [ 1.728679] en-vdd-vcm-2v8: disabling [ 1.728681] vdd-sys-bl: disabling [ 1.728683] ALSA device list: [ 1.728686] #0: tegra-hda at 0x3518000 irq 383 [ 1.728687] #1: tegra-snd-t186ref-mobile-rt565x [ 1.824594] tegra-pcie 10003000.pcie-controller: link 2 down, retrying [ 2.028612] tegra_cec 3960000.tegra_cec: Can't find physical addresse. [ 2.028617] tegra_cec 3960000.tegra_cec: tegra_cec_init Done. [ 2.226657] tegra-pcie 10003000.pcie-controller: link 2 down, retrying [ 2.228681] tegra-pcie 10003000.pcie-controller: link 2 down, ignoring [ 2.335112] tegra-pcie 10003000.pcie-controller: PCI host bridge to bus 0000:00 [ 2.335117] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.335120] pci_bus 0000:00: root bus resource [mem 0x40100000-0x47ffffff] [ 2.335123] pci_bus 0000:00: root bus resource [mem 0x48000000-0x7fffffff pref] [ 2.335127] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.335154] pci 0000:00:01.0: [10de:10e5] type 01 class 0x060400 [ 2.335258] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.335417] iommu: Adding device 0000:00:01.0 to group 55 [ 2.335423] arm-smmu: forcing sodev map for 0000:00:01.0 [ 2.335486] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.335621] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000 [ 2.335665] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x00ff] [ 2.335725] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit pref] [ 2.335764] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 2.336018] pci 0000:01:00.0: supports D1 D2 [ 2.336020] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.336215] iommu: Adding device 0000:01:00.0 to group 56 [ 2.336218] arm-smmu: forcing sodev map for 0000:01:00.0 [ 2.344682] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.344721] pci 0000:00:01.0: BAR 15: assigned [mem 0x48000000-0x480fffff 64bit pref] [ 2.344724] pci 0000:00:01.0: BAR 13: assigned [io 0x1000-0x1fff] [ 2.344729] pci 0000:01:00.0: BAR 4: assigned [mem 0x48000000-0x48003fff 64bit pref] [ 2.344760] pci 0000:01:00.0: BAR 2: assigned [mem 0x48004000-0x48004fff 64bit pref] [ 2.344791] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 2.344803] pci 0000:00:01.0: PCI bridge to [bus 01] [ 2.344807] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff] [ 2.344817] pci 0000:00:01.0: bridge window [mem 0x48000000-0x480fffff 64bit pref] [ 2.345034] pcieport 0000:00:01.0: Signaling PME through PCIe PME interrupt [ 2.345036] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 2.345042] pcie_pme 0000:00:01.0:pcie001: service driver pcie_pme loaded [ 2.345111] aer 0000:00:01.0:pcie002: service driver aer loaded [ 2.345319] r8168 0000:01:00.0: enabling device (0000 -> 0003) [ 2.345368] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded [ 2.367016] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [ 2.367029] r8168 Copyright (C) 2017 Realtek NIC software team This program comes with ABSOLUTELY NO WARRANTY; for details, please see . This is free software, and you are welcome to redistribute it under certain conditions; see . [ 4.237249] Wake76 for irq=199 [ 4.237252] Wake77 for irq=199 [ 4.237253] Wake78 for irq=199 [ 4.237254] Wake79 for irq=199 [ 4.237255] Wake80 for irq=199 [ 4.237257] Wake81 for irq=199 [ 4.237258] Wake82 for irq=199 [ 4.237279] tegra-xusb 3530000.xhci: Upgrade port 0 to USB3.0 [ 4.237282] tegra-xusb 3530000.xhci: Upgrade port 1 to USB3.0 [ 4.340746] usb usb2: usb_suspend_both: status 0 [ 4.540604] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.541793] ata1.00: ATA-8: HGST HTS721010A9E630, JB0OA3U0, max UDMA/133 [ 4.541797] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 4.543100] ata1.00: configured for UDMA/133 [ 4.543346] scsi 0:0:0:0: Direct-Access ATA HGST HTS721010A9 A3U0 PQ: 0 ANSI: 5 [ 4.572903] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 4.572907] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.573010] sd 0:0:0:0: [sda] Write Protect is off [ 4.573014] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 4.573060] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.611092] sda: sda1 sda2 sda3 sda4 sda5 [ 4.611807] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.614050] Freeing unused kernel memory: 8576K [ 4.635166] Root device found: mmcblk0p1 [ 4.635988] Found dev node: /dev/mmcblk0p1 [ 4.657845] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 4.658468] Rootfs mounted over mmcblk0p1 [ 4.680310] Switching from initrd to actual rootfs [ 4.812804] ip_tables: (C) 2000-2006 Netfilter Core Team [ 4.821402] cgroup: cgroup2: unknown option "nsdelegate" [ 4.840701] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [ 4.841437] systemd[1]: Detected architecture arm64. [ 4.858354] systemd[1]: No hostname configured. [ 4.858366] systemd[1]: Set hostname to . [ 4.950437] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 4.950445] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 5.063985] random: systemd: uninitialized urandom read (16 bytes read) [ 5.065411] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 5.065507] random: systemd: uninitialized urandom read (16 bytes read) [ 5.065524] systemd[1]: Reached target Swap. [ 5.065557] random: systemd: uninitialized urandom read (16 bytes read) [ 5.066800] systemd[1]: Created slice System Slice. [ 5.066857] systemd[1]: Reached target Slices. [ 5.098895] gpio tegra-gpio-aon wake30 for gpio=60(FF:4) [ 5.108033] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null) [ 5.314619] systemd-journald[2256]: Received request to flush runtime journal from PID 1 [ 5.849185] using random self ethernet address [ 5.853830] using random host ethernet address [ 5.996735] random: crng init done [ 6.000145] random: 7 urandom warning(s) missed due to ratelimiting [ 6.238779] dhd_module_init in [ 6.238851] found wifi platform device bcmdhd_wlan [ 6.240374] wifi_platform_get_country_code_map: could not get country_code_map [ 6.240379] wifi_plat_dev_drv_probe:platform country code map is not available [ 6.240398] Power-up adapter 'DHD generic adapter' [ 6.240404] wifi_platform_set_power = 1 [ 6.245551] Mass Storage Function, version: 2009/09/11 [ 6.245557] LUN: removable file: (no medium) [ 6.250385] using random self ethernet address [ 6.256774] using random host ethernet address [ 6.297821] rndis0: HOST MAC 5a:b9:3f:c9:d3:b8 [ 6.297883] rndis0: MAC 5a:b9:3f:c9:d3:b9 [ 6.301080] usb0: HOST MAC 5a:b9:3f:c9:d3:ba [ 6.301105] usb0: MAC 5a:b9:3f:c9:d3:bb [ 6.301137] tegra-xudc-new 3550000.xudc: ep 0 (type: 0, dir: out) enabled [ 6.310029] l4tbr0: port 1(rndis0) entered blocking state [ 6.310034] l4tbr0: port 1(rndis0) entered disabled state [ 6.310142] device rndis0 entered promiscuous mode [ 6.316884] IPv6: ADDRCONF(NETDEV_UP): rndis0: link is not ready [ 6.322342] l4tbr0: port 2(usb0) entered blocking state [ 6.322347] l4tbr0: port 2(usb0) entered disabled state [ 6.322457] device usb0 entered promiscuous mode [ 6.333127] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready [ 6.447179] wifi_platform_bus_enumerate device present 1 [ 6.471581] wifi_platform_bus_enumerate device present 0 [ 6.472356] F1 signature read @0x18000000=0x17214354 [ 6.481013] F1 signature OK, socitype:0x1 chip:0x4354 rev:0x1 pkg:0x2 [ 6.482492] DHD: dongle ram size is set to 786432(orig 786432) at 0x180000 [ 6.482577] wifi_platform_get_mac_addr [ 6.495383] ids dhd_log_netlink_init [ 6.498371] wl_create_event_handler(): thread:wl_event_handler:1197 started [ 6.498372] wl_event_handler : [ 6.498375] tsk Enter, tsk = 0xffffffc1d9401a90 [ 6.500634] dhd_attach(): thread:dhd_watchdog_thread:119b started [ 6.503308] dhd_attach(): thread:dhd_dpc:119d started [ 6.504934] dhd_attach(): thread:dhd_rxf:11a0 started [ 6.504945] dhd_deferred_work_init: work queue initialized [ 6.505705] Dongle Host Driver, version 1.201.82 (r) Compiled from [ 6.506064] Register interface [wlan0] MAC: 00:04:4b:8d:80:d3 [ 6.506068] dhd_prot_ioctl : bus is down. we have nothing to do [ 6.506202] sdhci-tegra 3440000.sdhci: Tuning done, restoring the best tap value : 61 [ 6.507246] wifi_platform_set_power = 0 [ 6.531779] android_work: did not send uevent (0 0 (null)) [ 6.600871] android_work: sent uevent USB_STATE=CONNECTED [ 6.611713] android_work: sent uevent USB_STATE=DISCONNECTED [ 6.700843] android_work: sent uevent USB_STATE=CONNECTED [ 6.704778] configfs-gadget gadget: high-speed config #1: c [ 6.704816] tegra-xudc-new 3550000.xudc: ep 5 (type: 3, dir: in) enabled [ 6.704831] tegra-xudc-new 3550000.xudc: ep 3 (type: 2, dir: in) enabled [ 6.704847] tegra-xudc-new 3550000.xudc: ep 2 (type: 2, dir: out) enabled [ 6.704928] tegra-xudc-new 3550000.xudc: ep 9 (type: 3, dir: in) enabled [ 6.704945] tegra-xudc-new 3550000.xudc: ep 7 (type: 2, dir: in) enabled [ 6.704959] tegra-xudc-new 3550000.xudc: ep 4 (type: 2, dir: out) enabled [ 6.704993] tegra-xudc-new 3550000.xudc: ep 15 (type: 3, dir: in) enabled [ 6.705012] tegra-xudc-new 3550000.xudc: ep 11 (type: 2, dir: in) enabled [ 6.705034] tegra-xudc-new 3550000.xudc: ep 6 (type: 2, dir: out) enabled [ 6.705112] IPv6: ADDRCONF(NETDEV_CHANGE): rndis0: link becomes ready [ 6.705272] android_work: sent uevent USB_STATE=CONFIGURED [ 6.707709] tegra-xudc-new 3550000.xudc: ep 13 (type: 2, dir: in) enabled [ 6.707727] tegra-xudc-new 3550000.xudc: ep 8 (type: 2, dir: out) enabled [ 6.707864] IPv6: ADDRCONF(NETDEV_CHANGE): usb0: link becomes ready [ 6.708847] tegra-xudc-new 3550000.xudc: ep 13 disabled [ 6.708944] tegra-xudc-new 3550000.xudc: ep 8 disabled [ 6.729059] tegra-xudc-new 3550000.xudc: ep 13 (type: 2, dir: in) enabled [ 6.729077] tegra-xudc-new 3550000.xudc: ep 8 (type: 2, dir: out) enabled [ 6.988634] tegra-xusb 3530000.xhci: entering ELPG [ 6.991583] tegra-xusb 3530000.xhci: entering ELPG done [ 9.648406] Please complete system configuration setup on the serial port provided by Jetson's USB device mode connection. e.g. /dev/ttyACMx where x can 0, 1, 2 etc. [ 10.267264] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null) [ 10.305107] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 10.387900] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 10.420512] l4tbr0: port 2(usb0) entered blocking state [ 10.420518] l4tbr0: port 2(usb0) entered forwarding state [ 10.420565] l4tbr0: port 1(rndis0) entered blocking state [ 10.420597] l4tbr0: port 1(rndis0) entered forwarding state [ 10.421784] IPv6: ADDRCONF(NETDEV_UP): l4tbr0: link is not ready [ 10.421804] IPv6: ADDRCONF(NETDEV_CHANGE): l4tbr0: link becomes ready [ 10.444426] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 10.451251] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null) [ 10.525396] gpio tegra-gpio wake18 for gpio=101(M:5) [ 10.527678] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 10.535752] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 10.537606] eth1: 0xffffff800b4a3000, 00:00:00:00:00:03, IRQ 458 [ 10.771193] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 10.795208] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 10.795324] Dongle Host Driver, version 1.201.82 (r) Compiled from [ 10.795333] wl_android_wifi_on in [ 10.795338] wifi_platform_set_power = 1 [ 11.004601] vdd-1v8: voltage operation not allowed [ 11.009423] sdhci-tegra 3440000.sdhci: could not set regulator OCR (-1) [ 11.036786] vdd-1v8: voltage operation not allowed [ 11.041608] sdhci-tegra 3440000.sdhci: could not set regulator OCR (-1) [ 11.065598] vdd-1v8: voltage operation not allowed [ 11.070435] sdhci-tegra 3440000.sdhci: could not set regulator OCR (-1) [ 11.079505] vdd-1v8: voltage operation not allowed [ 11.084343] sdhci-tegra 3440000.sdhci: could not set regulator OCR (-1) [ 11.191373] vdd-1v8: voltage operation not allowed [ 11.196201] sdhci-tegra 3440000.sdhci: could not set regulator OCR (-1) [ 11.203714] vdd-1v8: voltage operation not allowed [ 11.208536] sdhci-tegra 3440000.sdhci: could not set regulator OCR (-1) [ 11.216643] vdd-1v8: voltage operation not allowed [ 11.221445] sdhci-tegra 3440000.sdhci: could not set regulator OCR (-1) [ 11.228089] sdhci-tegra 3440000.sdhci: Tuning done, restoring the best tap value : 61 [ 11.228678] F1 signature read @0x18000000=0x17214354 [ 11.233222] F1 signature OK, socitype:0x1 chip:0x4354 rev:0x1 pkg:0x2 [ 11.233832] DHD: dongle ram size is set to 786432(orig 786432) at 0x180000 [ 11.328177] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded. [ 11.372808] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us) [ 11.373064] gpio tegra-gpio-aon wake69 for gpio=59(FF:3) [ 11.373115] gpio tegra-gpio-aon wake69 for gpio=59(FF:3) [ 11.373117] Enabling wake69 [ 11.373851] wifi_platform_get_mac_addr [ 11.375763] Firmware up: op_mode=0x0005, MAC=00:04:4b:8d:80:d3 [ 11.379895] clm path from default:/lib/firmware/brcm/bcmdhd.clm_blob [ 11.379925] Skipping the clm download. len:0 memblk: (null) [ 11.382107] dhd_preinit_ioctls pspretend_threshold for HostAPD failed -23 [ 11.386913] Firmware version = wl0: Nov 6 2019 21:22:23 version 7.35.349.85 (r723239 CY) FWID 01-a59d25b5 [ 11.389173] dhd_interworking_enable: failed to set WNM info, ret=-23 [ 12.035363] eqos 2490000.ether_qos eth0: Link is Up - 100Mbps/Full - flow control off [ 12.035936] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 12.821324] CFGP2P-ERROR) wl_cfgp2p_add_p2p_disc_if : [ 12.821328] P2P interface registered [ 12.829466] WLC_E_IF: NO_IF set, event Ignored [ 12.837424] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 34.090042] bcm54xx_low_power_mode(): put phy in iddq-lp mode [ 34.138859] l4tbr0: port 2(usb0) entered disabled state [ 34.138900] l4tbr0: port 1(rndis0) entered disabled state [ 34.140352] tegra-xudc-new 3550000.xudc: ep 3 disabled [ 34.140422] tegra-xudc-new 3550000.xudc: ep 2 disabled [ 34.140438] tegra-xudc-new 3550000.xudc: ep 3 (type: 2, dir: in) enabled [ 34.140453] tegra-xudc-new 3550000.xudc: ep 2 (type: 2, dir: out) enabled [ 34.142992] tegra-xudc-new 3550000.xudc: ep 13 disabled [ 34.143088] tegra-xudc-new 3550000.xudc: ep 8 disabled [ 34.143103] tegra-xudc-new 3550000.xudc: ep 13 (type: 2, dir: in) enabled [ 34.143118] tegra-xudc-new 3550000.xudc: ep 8 (type: 2, dir: out) enabled [ 34.172646] wl_android_wifi_off in [ 34.173635] dhd_wlfc_deinit():3472, maintain HOST RXRERODER flag in tvl [ 34.174026] dhdsdio_isr : bus is down. we have nothing to do [ 34.174055] gpio tegra-gpio-aon wake69 for gpio=59(FF:3) [ 34.174057] Disabling wake69 [ 34.174136] sdhci-tegra 3440000.sdhci: Tuning done, restoring the best tap value : 61 [ 34.175177] wifi_platform_set_power = 0 [ 38.629377] gpio tegra-gpio wake18 for gpio=101(M:5) [ 38.633939] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 40.139074] eqos 2490000.ether_qos eth0: Link is Up - 100Mbps/Full - flow control off [ 40.139661] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 90.866960] CPU1: shutdown [ 90.869724] psci: CPU1 killed. [ 90.913345] CPU2: shutdown [ 90.916061] psci: CPU2 killed. [ 92.736971] zram: Added device: zram0 [ 92.737671] zram: Added device: zram1 [ 92.738115] zram: Added device: zram2 [ 92.738451] zram: Added device: zram3 [ 92.763005] zram0: detected capacity change from 0 to 1030201344 [ 92.782097] Adding 1006052k swap on /dev/zram0. Priority:5 extents:1 across:1006052k SS [ 92.789013] zram1: detected capacity change from 0 to 1030201344 [ 92.810229] Adding 1006052k swap on /dev/zram1. Priority:5 extents:1 across:1006052k SS [ 92.821279] zram2: detected capacity change from 0 to 1030201344 [ 92.843194] Adding 1006052k swap on /dev/zram2. Priority:5 extents:1 across:1006052k SS [ 92.847538] zram3: detected capacity change from 0 to 1030201344 [ 92.874785] Adding 1006052k swap on /dev/zram3. Priority:5 extents:1 across:1006052k SS [ 93.209942] tegra-xudc-new 3550000.xudc: ep 3 disabled [ 93.209965] tegra-xudc-new 3550000.xudc: ep 2 disabled [ 93.209983] tegra-xudc-new 3550000.xudc: ep 5 disabled [ 93.210080] tegra-xudc-new 3550000.xudc: ep 4 disabled [ 93.210092] tegra-xudc-new 3550000.xudc: ep 7 disabled [ 93.210119] tegra-xudc-new 3550000.xudc: ep 9 disabled [ 93.210142] tegra-xudc-new 3550000.xudc: ep 13 disabled [ 93.210170] tegra-xudc-new 3550000.xudc: ep 8 disabled [ 93.210188] tegra-xudc-new 3550000.xudc: ep 15 disabled [ 93.210205] tegra-xudc-new 3550000.xudc: ep 11 disabled [ 93.210224] android_work: sent uevent USB_STATE=DISCONNECTED [ 93.210228] tegra-xudc-new 3550000.xudc: ep 6 disabled [ 93.210711] tegra-xudc-new 3550000.xudc: ep 0 disabled [ 93.226829] device usb0 left promiscuous mode [ 93.226835] l4tbr0: port 2(usb0) entered disabled state [ 93.289509] device rndis0 left promiscuous mode [ 93.289515] l4tbr0: port 1(rndis0) entered disabled state [ 95.240899] tegradc 15210000.nvdisplay: blank - powerdown [ 95.624038] fuse init (API version 7.26) [ 97.383601] using random self ethernet address [ 97.388291] using random host ethernet address [ 97.638878] Mass Storage Function, version: 2009/09/11 [ 97.638884] LUN: removable file: (no medium) [ 97.645938] using random self ethernet address [ 97.650448] using random host ethernet address [ 97.664747] rndis0: HOST MAC 5a:b9:3f:c9:d3:b8 [ 97.664926] rndis0: MAC 5a:b9:3f:c9:d3:b9 [ 97.665667] usb0: HOST MAC 5a:b9:3f:c9:d3:ba [ 97.665816] usb0: MAC 5a:b9:3f:c9:d3:bb [ 97.665853] tegra-xudc-new 3550000.xudc: ep 0 (type: 0, dir: out) enabled [ 97.665949] android_work: did not send uevent (0 0 (null)) [ 97.681274] l4tbr0: port 1(rndis0) entered blocking state [ 97.681279] l4tbr0: port 1(rndis0) entered disabled state [ 97.681734] device rndis0 entered promiscuous mode [ 97.687959] IPv6: ADDRCONF(NETDEV_UP): rndis0: link is not ready [ 97.694020] l4tbr0: port 2(usb0) entered blocking state [ 97.694025] l4tbr0: port 2(usb0) entered disabled state [ 97.694778] device usb0 entered promiscuous mode [ 97.700363] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready [ 97.921969] android_work: did not send uevent (0 0 (null)) [ 97.991081] android_work: sent uevent USB_STATE=CONNECTED [ 98.002047] android_work: sent uevent USB_STATE=DISCONNECTED [ 98.090802] android_work: sent uevent USB_STATE=CONNECTED [ 98.098339] configfs-gadget gadget: high-speed config #1: c [ 98.098370] tegra-xudc-new 3550000.xudc: ep 5 (type: 3, dir: in) enabled [ 98.098386] tegra-xudc-new 3550000.xudc: ep 3 (type: 2, dir: in) enabled [ 98.098402] tegra-xudc-new 3550000.xudc: ep 2 (type: 2, dir: out) enabled [ 98.098476] tegra-xudc-new 3550000.xudc: ep 9 (type: 3, dir: in) enabled [ 98.098492] tegra-xudc-new 3550000.xudc: ep 7 (type: 2, dir: in) enabled [ 98.098507] tegra-xudc-new 3550000.xudc: ep 4 (type: 2, dir: out) enabled [ 98.098595] tegra-xudc-new 3550000.xudc: ep 15 (type: 3, dir: in) enabled [ 98.098613] tegra-xudc-new 3550000.xudc: ep 11 (type: 2, dir: in) enabled [ 98.098633] tegra-xudc-new 3550000.xudc: ep 6 (type: 2, dir: out) enabled [ 98.098672] IPv6: ADDRCONF(NETDEV_CHANGE): rndis0: link becomes ready [ 98.098872] android_work: sent uevent USB_STATE=CONFIGURED [ 98.103798] tegra-xudc-new 3550000.xudc: ep 13 (type: 2, dir: in) enabled [ 98.103818] tegra-xudc-new 3550000.xudc: ep 8 (type: 2, dir: out) enabled [ 98.103930] IPv6: ADDRCONF(NETDEV_CHANGE): usb0: link becomes ready [ 98.105112] tegra-xudc-new 3550000.xudc: ep 13 disabled [ 98.105204] tegra-xudc-new 3550000.xudc: ep 8 disabled [ 98.123383] tegra-xudc-new 3550000.xudc: ep 13 (type: 2, dir: in) enabled [ 98.123402] tegra-xudc-new 3550000.xudc: ep 8 (type: 2, dir: out) enabled [ 102.103567] l4tbr0: port 2(usb0) entered blocking state [ 102.103572] l4tbr0: port 2(usb0) entered forwarding state [ 102.103638] l4tbr0: port 1(rndis0) entered blocking state [ 102.103641] l4tbr0: port 1(rndis0) entered forwarding state [ 102.119821] IPv6: ADDRCONF(NETDEV_UP): l4tbr0: link is not ready [ 102.119856] IPv6: ADDRCONF(NETDEV_CHANGE): l4tbr0: link becomes ready [ 104.200525] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 104.200535] Bluetooth: BNEP socket layer initialized [ 431.845741] systemd: 37 output lines suppressed due to ratelimiting [ 431.860820] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [ 431.861553] systemd[1]: Detected architecture arm64. [ 431.968625] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 431.986017] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 432.788725] systemd[1]: Stopping Journal Service... [ 432.789331] systemd-journald[2256]: Received SIGTERM from PID 1 (systemd). [ 432.793562] systemd[1]: Stopped Journal Service. [ 432.797897] systemd[1]: Starting Journal Service... [ 432.877845] systemd[1]: Started Journal Service. [ 683.458799] CFGP2P-ERROR) wl_cfgp2p_del_p2p_disc_if : [ 683.458803] P2P interface unregistered [ 683.591365] Dongle Host Driver, version 1.201.82 (r) Compiled from [ 683.591378] wl_android_wifi_on in [ 683.591384] wifi_platform_set_power = 1 [ 683.802868] vdd-1v8: voltage operation not allowed [ 683.807717] sdhci-tegra 3440000.sdhci: could not set regulator OCR (-1) [ 683.834946] vdd-1v8: voltage operation not allowed [ 683.839799] sdhci-tegra 3440000.sdhci: could not set regulator OCR (-1) [ 683.863783] vdd-1v8: voltage operation not allowed [ 683.868610] sdhci-tegra 3440000.sdhci: could not set regulator OCR (-1) [ 683.879337] vdd-1v8: voltage operation not allowed [ 683.884177] sdhci-tegra 3440000.sdhci: could not set regulator OCR (-1) [ 683.993552] vdd-1v8: voltage operation not allowed [ 683.998407] sdhci-tegra 3440000.sdhci: could not set regulator OCR (-1) [ 684.005955] vdd-1v8: voltage operation not allowed [ 684.010805] sdhci-tegra 3440000.sdhci: could not set regulator OCR (-1) [ 684.019004] vdd-1v8: voltage operation not allowed [ 684.023830] sdhci-tegra 3440000.sdhci: could not set regulator OCR (-1) [ 684.030491] sdhci-tegra 3440000.sdhci: Tuning done, restoring the best tap value : 61 [ 684.031065] F1 signature read @0x18000000=0x17214354 [ 684.035439] F1 signature OK, socitype:0x1 chip:0x4354 rev:0x1 pkg:0x2 [ 684.036061] DHD: dongle ram size is set to 786432(orig 786432) at 0x180000 [ 684.099194] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded. [ 684.143710] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us) [ 684.143973] gpio tegra-gpio-aon wake69 for gpio=59(FF:3) [ 684.143996] gpio tegra-gpio-aon wake69 for gpio=59(FF:3) [ 684.143998] Enabling wake69 [ 684.144747] wifi_platform_get_mac_addr [ 684.146697] Firmware up: op_mode=0x0005, MAC=00:04:4b:8d:80:d3 [ 684.150962] clm path from default:/lib/firmware/brcm/bcmdhd.clm_blob [ 684.150985] Skipping the clm download. len:0 memblk: (null) [ 684.153188] dhd_preinit_ioctls pspretend_threshold for HostAPD failed -23 [ 684.158086] Firmware version = wl0: Jul 21 2020 16:35:45 version 7.35.349.94 (r726700 CY) FWID 01-aa356e32 [ 684.160390] dhd_interworking_enable: failed to set WNM info, ret=-23 [ 684.243253] CFGP2P-ERROR) wl_cfgp2p_add_p2p_disc_if : [ 684.243257] P2P interface registered [ 684.251950] WLC_E_IF: NO_IF set, event Ignored [ 684.261422] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready