3438.872174] watchdog: watchdog0: watchdog did not stop! [ 3438.877111] systemd-shutdow: 56 output lines suppressed due to ratelimiting [ 3439.899357] reboot: Restarting system ▒▒▒▒Shutdown state requested 1 Rebooting system ... WARNING: at platform/drivers/cl▒▒ [0000.053] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fuses. [0000.062] I> MB1 (prd-version: 1.5.1.7-t194-41334769-98030a79) [0000.067] I> Boot-mode: Coldboot [0000.070] I> Chip revision : A02P [0000.073] I> Bootrom patch version : 15 (correctly patched) [0000.078] I> ATE fuse revision : 0x200 [0000.082] I> Ram repair fuse : 0x0 [0000.085] I> Ram Code : 0x2 [0000.088] I> rst_source : 0xb [0000.090] I> rst_level : 0x1 [0000.094] I> Boot-device: eMMC [0000.109] I> sdmmc DDR50 mode [0000.113] W> No valid slot number is found in scratch register [0000.118] W> Return default slot: _a [0000.122] I> Active Boot chain : 0 [0000.125] I> Boot-device: eMMC [0000.128] W> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT. [0000.135] I> Temperature = 29500 [0000.138] W> Skipping boost for clk: BPMP_CPU_NIC [0000.142] W> Skipping boost for clk: BPMP_APB [0000.146] W> Skipping boost for clk: AXI_CBB [0000.150] W> Skipping boost for clk: AON_CPU_NIC [0000.154] W> Skipping boost for clk: CAN1 [0000.158] W> Skipping boost for clk: CAN2 [0000.162] I> Boot-device: eMMC [0000.165] I> Boot-device: eMMC [0000.174] I> Sdmmc: HS400 mode enabled [0000.179] I> ECC region[0]: Start:0x0, End:0x0 [0000.183] I> ECC region[1]: Start:0x0, End:0x0 [0000.187] I> ECC region[2]: Start:0x0, End:0x0 [0000.191] I> ECC region[3]: Start:0x0, End:0x0 [0000.195] I> ECC region[4]: Start:0x0, End:0x0 [0000.200] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000 [0000.205] I> Non-ECC region[1]: Start:0x0, End:0x0 [0000.210] I> Non-ECC region[2]: Start:0x0, End:0x0 [0000.214] I> Non-ECC region[3]: Start:0x0, End:0x0 [0000.219] I> Non-ECC region[4]: Start:0x0, End:0x0 [0000.224] E> FAILED: Thermal config [0000.231] E> FAILED: MEMIO rail config [0000.250] I> Boot-device: eMMC [0000.259] I> sdmmc bdev is already initialized [0000.332] I> MB1 done ▒▒▒▒main enter SPE VERSION #: R01.00.14 Created: Sep 19 2018 @ 11:03:21 HW Function test Start Scheduler. in late init ▒▒ [0000.340] I> Welcome to MB2(TBoot-BPMP) (version: 00.00.2018.32-mobile-938a8cd8) [0000.341] I> DMA Heap @ [0x526fa000 - 0x52ffa000] [0000.341] I> Default Heap @ [0xd486400 - 0xd48a400] [0000.342] E> DEVICE_PROD: Invalid value data = 70020000, size = 0. [0000.348] W> device prod register failed [0000.352] I> Boot-device: eMMC [0000.354] I> Boot_device: SDMMC_BOOT instance: 3 [0000.360] I> sdmmc-3 params source = boot args [0000.363] I> sdmmc bdev is already initialized [0000.367] I> sdmmc-3 params source = boot args [0000.376] I> Found 17 partitions in SDMMC_BOOT (instance 3) [0000.382] I> Found 42 partitions in SDMMC_USER (instance 3) [0000.383] W> No valid slot number is found in scratch register [0000.388] W> Return default slot: _a [0000.392] I> Active Boot chain : 0 [0000.395] I> parsing oem signed section of bpmp-fw header done [0000.401] I> bpmp-fw binary init read from storage [0000.406] I> oem authentication of bpmp-fw header done [0000.412] I> bpmp-fw binary done read from storage [0000.415] I> bpmp-fw: Authentication init Done [0000.420] I> parsing oem signed section of cpubl header done [0000.425] I> cpubl binary init read from storage [0000.429] I> bpmp-fw: Authentication Finalize Done [0000.434] I> oem authentication of cpubl header done [0000.439] I> cpubl binary done read from storage [0000.443] I> cpubl: Authentication init Done [0000.448] I> parsing oem signed section of rce header done [0000.453] I> rce binary init read from storage [0000.457] I> Relocating BR-BCT [0000.460] I> cpubl: Authentication Finalize Done [0000.465] I> oem authentication of rce header done [0000.469] I> rce binary done read from storage [0000.473] I> rce: Authentication init Done [0000.478] I> parsing oem signed section of ape header done [0000.482] I> ape binary init read from storage [0000.487] I> rce: Authentication Finalize Done [0000.491] I> oem authentication of ape header done [0000.496] I> ape binary done read from storage [0000.500] I> ape: Authentication init Done [0000.505] I> parsing oem signed section of tos header done [0000.509] I> tos binary init read from storage [0000.514] I> ape: Authentication Finalize Done [0000.518] I> oem authentication of tos header done [0000.522] I> tos binary done read from storage [0000.527] I> tos: Authentication init Done [0000.531] I> parsing oem signed section of bpmp-fw-dtb header done [0000.537] I> bpmp-fw-dtb binary init read from storage [0000.542] I> tos: Authentication Finalize Done [0000.548] I> oem authentication of bpmp-fw-dtb header done [0000.554] I> bpmp-fw-dtb binary done read from storage [0000.556] I> bpmp-fw-dtb: Authentication init Done [0000.561] I> parsing oem signed section of cpubl-dtb header done [0000.567] I> cpubl-dtb binary init read from storage [0000.572] I> bpmp-fw-dtb: Authentication Finalize Done [0000.774] I> oem authentication of cpubl-dtb header done [0000.775] I> cpubl-dtb binary done read from storage [0000.775] I> cpubl-dtb: Authentication init Done [0000.777] I> parsing oem signed section of eks header done [0000.778] I> eks binary init read from storage [0000.778] I> cpubl-dtb: Authentication Finalize Done [0000.779] I> oem authentication of eks header done [0000.783] I> eks binary done read from storage [0000.787] I> eks: Authentication init Done [0000.791] I> eks: Authentication Finalize Done [0000.795] I> EKB detected (length: 0x410) @ VA:0x52700400 ▒▒NOTICE: BL31: v1.3(release):b5eeb33f7 NOTICE: BL31: Built : 12:15:32, Jul 26 2021 ipc-unittest-main: 1519: Welcome to IPC unittest!!! ipc-unittest-main: 1531: waiting forever ipc-unittest-srv: 329: Init unittest services!!! hwkey-agent: 41: hwkey-agent is running!! hwkey-agent: 315: key_mgnt_processing ....... hwkey-agent: 223: Setting EKB key 0 to slot 14 hwkey-agent: 178: Init hweky-agent services!! luks-srv: 40: luks-srv is running!! luks-srv: 157: Init luks-srv IPC services!! platform_bootstrap_epilog: trusty bootstrap complete ▒▒ welcome to lk calling constructors initializing heap creating bootstrap completion thread top of bootstrap2() initializing platform bpmp: platform_init tag is e73a758761f0c6d24a1e69a2ac6b5035 tag_show initialized dt initialized mail initialized chipid initialized fuse initialized sku initialized speedo initialized ec_get_ec_list: found 45 ecs ec initialized ec_mrq initialized vmon_populate_monitors: found 3 monitors vmon initialized adc initialized fmon_populate_monitors: found 73 monitors fmon initialized fmon_mrq initialized reset initialized nvhs initialized 392 clocks registered WARNING: pll_c4 has no dyn ramp clk_mrq_init: mrq handler registered clk initialized nvlink initialized io_dpd initialized io_dpd initialized thermal initialized i2c5 controller initialized initialized i2c mrq handling i2c initialized regulator initialized avfs_clk_platform initialized soctherm initialized aotag initialized powergate initialized dvs initialized pm initialized pg_late initialized strap initialized tag initialized emc initialized clk_dt initialized avfs_ccplex_platform initialized tj_max: dt node not found tj_init initialized uphy_mrq_init: mrq handler registered uphy_dt initialized uphy initialized safereg_init: period 80 ms ec_late initialized ▒▒ ▒▒mrq initialized ▒▒[0001.298] I> Welcome to Cboot ▒▒fmon_post initialized ▒▒[0001.298] I> Cboot Version: t194-cfa2bc91 [0001.299] I> CPU-BL Params @ 0xf2820000 [0001.300] I> 0) Base:0x00000000 Size:0x00000000 [0001.304] I> 1) Base:0xf1100000 Size:0x00100000 [0001.309] I> 2) Base:0xf2000000 Size:0x00200000 [0001.313] I> 3) Base:0xf1200000 Size:0x00200000 [0001.318] I> 4) Base:0xf1000000 Size:0x00100000 [0001.322] I> 5) Base:0xf0f00000 Size:0x00100000 [0001.327] I> 6) Base:0xf3800000 Size:0x00400000 ▒▒clk_set_parent failed for clk i2c2, parent pll_aon (-22) clk_set_parent failed for clk i2c8, parent pll_aon (-22) clk_dt_late initialized machine_check initialized pm_post initialized dbells initialized avfs_clk_platform_post initialized dmce initialized cvc initialized ccplex_avfs_hw_init: nafll_cluster0: not monitored ccplex_avfs_hw_init: nafll_cluster1: not monitored ccplex_avfs_hw_init: nafll_cluster2: not monitored ccplex_avfs_hw_init: nafll_cluster3: not monitored avfs_clk_mach_post initialized regulator_post initialized rm initialized sc7_diag initialized thermal_test initialized serial_late initialized clk_post initialized clk_dt_post initialized mc_reg initialized pg_post initialized dyn_modules initialized sku_debugfs initialized speedo_debugfs initialized adc_debugfs initialized clk_debugfs initialized ▒▒[0001.331] I> 7) Base:0xf1c00000 Size:0x00400000 [0001.411] I> 8) Base:0xf0e00000 Size:0x00100000 [0001.415] I> 9) Base:0xf0d00000 Size:0x00100000 [0001.420] I> 10) Base:0xf3000000 Size:0x00800000 [0001.424] I> 11) Base:0x40000000 Size:0x00040000 [0001.428] I> 12) Base:0xf0c00000 Size:0x00100000 [0001.433] I> 13) Base:0x40046000 Size:0x00002000 [0001.437] I> 14) Base:0x40048000 Size:0x00002000 [0001.442] I> 15) Base:0xac000000 Size:0x00004000▒▒emc_debugfs initialized dvs_debugfs initialized ▒▒ ▒▒fmon_debugfs initialized vmon_debugfs initialized pg_debugfs initialized profile_fs initialized debugfs_cons initialized mail_fs initialized profile initialized cvc_debugfs initialized dmce_debugfs initialized ec_debugfs initialized rm_debugfs initialized soctherm_debug initialized gr_reader initialized mods initialized dt_fs initialized debugfs_mrq initialized debug_mrq initialized debug_safereg initialized initializing target calling apps_init() starting app shell entering main console loop ] ▒▒[0001.451] I> 16) Base:0x4004a000 Size:0x00002000 [0001.502] I> 17) Base:0xf0b00000 Size:0x00100000 [0001.506] I> 18) Base:0x4004c000 Size:0x00002000 [0001.510] I> 19) Base:0xf2200000 Size:0x00600000 [0001.515] I> 20) Base:0x4004e000 Size:0x00002000 [0001.519] I> 21) Base:0xf0ad0000 Size:0x0000c000 [0001.524] I> 22) Base:0x00000000 Size:0x00000000 [0001.528] I> 23) Base:0xf0ae0000 Size:0x00020000 [0001.533] I> 24) Base:0xf6000000 Size:0x02000000 [0001.537] I> 25) Base:0x40050000 Size:0x00002000 [0001.542] I> 26) Base:0x40040000 Size:0x00006000 [0001.546] I> 27) Base:0xf1800000 Size:0x00400000 [0001.551] I> 28) Base:0xf4c00000 Size:0x01400000 [0001.555] I> 29) Base:0xf1400000 Size:0x00400000 [0001.560] I> 30) Base:0x00000000 Size:0x00000000 [0001.564] I> 31) Base:0x00000000 Size:0x00000000 [0001.568] I> 32) Base:0xf8000000 Size:0x08000000 [0001.573] I> 33) Base:0x00000000 Size:0x00000000 [0001.577] I> 34) Base:0xf3c00000 Size:0x01000000 [0001.582] I> 35) Base:0xab000000 Size:0x01000000 [0001.586] I> 36) Base:0xa0000000 Size:0x0b000000 [0001.591] I> 37) Base:0xf2800000 Size:0x00800000 [0001.595] I> 38) Base:0x80000000 Size:0x20000000 [0001.600] I> 39) Base:0xb0000000 Size:0x08000000 [0001.604] I> 40) Base:0x00000000 Size:0x00000000 [0001.609] I> 41) Base:0x00000000 Size:0x00000000 [0001.613] I> 42) Base:0x00000000 Size:0x00000000 [0001.618] I> 43) Base:0x00000000 Size:0x00000000 [0001.622] I> 44) Base:0x00000000 Size:0x00000000 [0001.626] I> 45) Base:0x00000000 Size:0x00000000 [0001.631] GIC-SPI Target CPU: 0 [0001.634] Interrupts Init done [0001.637] calling constructors [0001.640] initializing heap [0001.642] I> Heap: [0xa0699b80 ... 0xab000000] [0001.647] initializing threads [0001.649] initializing timers [0001.652] creating bootstrap completion thread [0001.657] top of bootstrap2() [0001.659] CPU: MIDR: 0x4E0F0040, MPIDR: 0x80000000 [0001.664] initializing platform [0001.667] E> DEVICE_PROD: Invalid value data = 0, size = 0. [0001.672] W> device prod register failed [0001.676] I> Bl_dtb @0xaaf00000 [0001.682] W> "plugin-manager" doesn't exist, creating [0001.684] W> "ids" doesn't exist, creating [0001.688] W> "connection" doesn't exist, creating [0001.693] W> "configs" doesn't exist, creating [0001.707] E> failed to read label property for node 227172: 13 [0001.709] E> failed to read reg property for node 227260: 13 [0001.712] E> failed to read label property for node 227312: 13 [0001.716] E> failed to read label property for node 227380: 13 [0001.721] E> failed to read label property for node 227416: 13 [0001.726] E> failed to read label property for node 227452: 13 [0001.732] E> failed to read reg property for node 227520: 13 [0001.737] E> failed to read label property for node 227572: 13 [0001.744] I> Find /i2c@3160000's alias i2c0 [0001.746] I> Reading eeprom i2c=0 address=0x50 [0001.776] I> Device at /i2c@3160000:0x50 [0001.776] I> Reading eeprom i2c=0 address=0x56 [0001.800] I> Device at /i2c@3160000:0x56 [0001.801] I> Find /i2c@3180000's alias i2c2 [0001.802] I> Reading eeprom i2c=2 address=0x54 [0001.803] E> I2C: slave not found in slaves. [0001.804] E> I2C: Could not write 0 bytes to slave: 0x00a8 with repeat start true. [0001.805] E> I2C_DEV: Failed to send register address 0x00000000. [0001.805] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa8 at 0x00000000 via instance 2. [0001.814] E> eeprom: Failed to read I2C slave device [0001.819] I> Eeprom read failed 0x3526070d [0001.823] I> Reading eeprom i2c=2 address=0x57 [0001.828] E> I2C: slave not found in slaves. [0001.832] E> I2C: Could not write 0 bytes to slave: 0x00ae with repeat start true. [0001.839] E> I2C_DEV: Failed to send register address 0x00000000. [0001.845] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xae at 0x00000000 via instance 2. [0001.854] E> eeprom: Failed to read I2C slave device [0001.859] I> Eeprom read failed 0x3526070d [0001.863] I> Reading eeprom i2c=2 address=0x52 [0001.868] E> I2C: slave not found in slaves. [0001.872] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.879] E> I2C_DEV: Failed to send register address 0x00000000. [0001.885] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 2. [0001.895] E> eeprom: Failed to read I2C slave device [0001.899] I> Eeprom read failed 0x3526070d [0001.904] I> Find /i2c@c240000's alias i2c1 [0001.907] I> Reading eeprom i2c=1 address=0x52 [0001.913] E> I2C: slave not found in slaves. [0001.916] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.924] E> I2C_DEV: Failed to send register address 0x00000000. [0001.929] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 1. [0001.939] E> eeprom: Retry to read I2C slave device. [0001.944] E> I2C: slave not found in slaves. [0001.948] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.955] E> I2C_DEV: Failed to send register address 0x00000000. [0001.961] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 1. [0001.970] E> eeprom: Failed to read I2C slave device [0001.975] I> Eeprom read failed 0x3526070d [0001.979] I> Reading eeprom i2c=1 address=0x50 [0001.984] E> I2C: slave not found in slaves. [0001.988] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true. [0001.995] E> I2C_DEV: Failed to send register address 0x00000000. [0002.001] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0x00000000 via instance 1. [0002.011] E> eeprom: Retry to read I2C slave device. [0002.015] E> I2C: slave not found in slaves. [0002.019] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true. [0002.027] E> I2C_DEV: Failed to send register address 0x00000000. [0002.033] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0x00000000 via instance 1. [0002.042] E> eeprom: Failed to read I2C slave device [0002.047] I> Eeprom read failed 0x3526070d [0002.051] I> create_pm_ids: id: 2888-0004-400-L, len: 15 [0002.056] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0002.067] I> create_pm_ids: id: 2822-0000-700-K, len: 15 [0002.072] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0002.084] I> Adding plugin-manager/ids/2888-0004-400=/i2c@3160000:module@0x50 [0002.092] W> "i2c@3160000" doesn't exist, creating [0002.095] W> "module@0x50" doesn't exist, creating [0002.100] I> Adding plugin-manager/ids/2822-0000-700=/i2c@3160000:module@0x56 [0002.107] W> "module@0x56" doesn't exist, creating [0002.113] I> Adding plugin-manager/cvm [0002.115] W> "chip-id" doesn't exist, creating [0002.119] I> Adding plugin-manager/chip-id/A02P [0002.124] I> Plugin-manager override starting [0002.129] I> node /plugin-manager/fragement-tegra-wdt-en matches [0002.136] I> node /plugin-manager/fragement-soft-wdt matches [0002.144] I> node /plugin-manager/fragment-pcie-c5-ep matches [0002.148] I> node /plugin-manager/fragment-tegra-ufs-lane10 matches [0002.160] I> Disable plugin-manager status in FDT [0002.160] I> Plugin-manager override finished successfully [0002.161] I> gpio framework initialized [0002.166] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio' driver [0002.173] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio-aon' driver [0002.180] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x46 [0002.187] W> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539 [0002.195] W> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539 [0002.201] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0002.207] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x44 [0002.215] W> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539 [0002.223] W> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539 [0002.229] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0002.237] I> fixed regulator driver initialized [0002.248] I> register 'maxim' power off handle [0002.249] I> virtual i2c enabled [0002.249] I> registered 'maxim,max20024' pmic [0002.251] I> tegrabl_gpio_driver_register: register 'max20024-gpio' driver [0002.258] I> Boot-device: eMMC [0002.261] I> Boot_device: SDMMC_BOOT instance: 3 [0002.269] I> sdmmc-3 params source = boot args [0002.270] I> create_pm_ids: id: 2888-0004-400-L, len: 15 [0002.275] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0002.286] I> create_pm_ids: id: 2822-0000-700-K, len: 15 [0002.291] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0002.302] I> sdmmc bdev is already initialized [0002.306] I> sdmmc-3 params source = boot args [0002.337] I> Found 17 partitions in SDMMC_BOOT (instance 3) [0002.350] I> Found 42 partitions in SDMMC_USER (instance 3) [0002.359] I> enabling 'vdd-hdmi-5v0' regulator [0002.363] I> regulator 'vdd-hdmi-5v0' already enabled [0002.364] I> hdmi cable connected [0002.366] W> set volts not configured for 'vdd-1v0' [0002.368] W> set volts not configured for 'vdd-1v8-hs' [0002.368] I> retrieved tmds range from prod_list_hdmi_soc [0002.372] E> invalid display type [0002.376] E> invalid display type [0002.377] E> cannot find any other nvdisp nodes [0002.392] I> edid read success [0002.392] I> width = 640, height = 480, frequency = 25174825 [0002.393] I> width = 640, height = 480, frequency = 25174825 [0002.393] I> width = 640, height = 480, frequency = 25174825 [0002.394] I> width = 640, height = 480, frequency = 25174825 [0002.397] I> width = 1920, height = 1080, frequency = 148500000 [0002.403] I> Best mode Width = 640, Height = 480, freq = 25174825 [0002.412] I> hdmi_enable, starting HDMI initialisation [0002.418] I> hdmi_enable, HDMI initialisation complete [0002.421] I> Load in CBoot Boot Options partition and parse it [0002.430] E> Error -9 when finding node with path /boot-configuration [0002.431] E> tegrabl_cbo_parse_info: "boot-configuration" not found in CBO file. [0002.438] I> Using default boot order [0002.441] I> boot-dev-order :- [0002.444] I> 1.sd [0002.446] I> 2.usb [0002.448] I> 3.nvme [0002.450] I> 4.emmc [0002.452] I> 5.net [0002.454] I> Hit any key to stop autoboot: 4 3 2 1 [0004.461] initializing target [0004.461] calling apps_init() [0004.462] starting app kernel_boot_app [0004.482] I> found decompressor handler: lz4-legacy [0004.482] I> decompressing BMP blob ... [0004.493] I> Kernel type = Normal [0004.494] I> ########## SD (0) boot ########## [0004.494] I> No sdcard [0004.494] I> -0 params source = [0004.494] E> Blockdev open: exit error [0004.495] E> SD boot failed, err: 724238353 [0004.495] I> ########## USB (0) boot ########## [0004.500] W> No valid slot number is found in scratch register [0004.500] W> Return default slot: _a [0004.508] I> Validate XUSB-FW ... [0004.508] I> T19x: Authenticate XUSB-FW (bin_type: 11), max size 0x28000 [0004.513] I> Encryption fuse is not ON [0004.515] I> USB Firmware Version: 60.09 release [0004.575] I> regulator of usb2-0 already enabled [0004.581] I> regulator of usb2-1 already enabled [0004.588] I> regulator of usb2-2 already enabled [0004.597] I> enabling 'vdd-5v-sata' regulator [0005.664] I> USB 2.0 port 1 new high-speed USB device detected [0005.666] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa4411200, cmd_ring.dma = 0xa4411280 [0005.767] I> Start to enumerate device [0005.768] W> WARNING: event and command not matching, cmd_trb_ptr = 0xa4411200, cmd_ring.dma = 0xa4411280 [0005.773] I> [0005.773] I> Enumerated USB Device 05e3:0608 [0005.773] I> [0005.775] I> Hub: [0005.775] I> Downstream ports : 4 [0005.775] I> Power switching : Ganged [0005.775] I> Compound device : No [0005.776] I> Over-current protection : Global [0005.780] I> Hub avg delay : 4 ns [0005.784] I> Enable hub ports [0005.792] I> Device detected on port 1 [0005.795] I> Device detected on port 4 [0006.806] I> Reset port 1 [0006.860] I> Port 1 device is low speed, skip enumeration [0006.863] I> Reset port 4 [0006.917] I> Port 4 device is low speed, skip enumeration [0006.918] E> Enumerated device doesn't belong to MSD class or protocol is not bulk-only!! [0006.918] E> Class = 9, Protocol = 0 [0006.918] E> USBMSD: Failed to initialize Enumerated USB device either not an MSD device or supported protoco[0006.919] E> USBMSD: Failed to open usbmsd open, 0. [0006.923] E> Error opening USBMSD driver 0, err: 7c7c0312 [0006.928] W> Failed to initialize device 5-0 [0006.932] E> USB boot failed, err: 2088502034 [0006.937] I> ########## NVME (0) boot ########## [0006.941] I> Initializing nvme device instance 0 [0006.946] I> Initializing nvme controller [0006.950] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14180000 [0006.956] I> vpcie3v3-supply not found [0006.959] I> vpcie12v-supply not found [0006.963] W> Failed to get nvidia,plat-gpios [0006.967] I> tegrabl_pcie_soc_preinit: (0): [0006.971] I> Unpowergate [0006.974] I> tegrabl_car_clk_disable(0) ... [0006.978] I> tegrabl_car_rst_set(CORE, 0) ... [0006.982] I> tegrabl_car_rst_set(APB, 0) ... [0006.986] I> tegrabl_car_clk_enable(0) ... [0006.990] I> tegrabl_car_rst_clear(APB, 0) ... [0006.994] I> tegrabl_set_ctrl_state(0) [0006.998] I> CLR PCIE_APB:6 [0007.000] I> tegrabl_pcie_soc_init: (0): [0007.004] I> APPL initialization ... [0007.007] I> poweron phys [0007.010] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14180000 [0007.016] I> tegrabl_power_on_phy: power on phy @0x3e30000 [0007.022] I> tegrabl_power_on_phy: power on phy @0x3e40000 [0007.027] I> tegrabl_power_on_phy: power on phy @0x3e50000 [0007.032] I> tegrabl_power_on_phy: power on phy @0x3e60000 [0008.138] C> Failed to link up controller-0 [0008.138] W> Failed tegrabl_pcie_soc_init(), error=0x12 [0008.139] I> Failed to initialize SoC Host PCIe controller [0008.139] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(0); error=0x12 [0008.140] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800612 [0008.140] W> Failed to open NVME-0, err = 80800612 [0008.145] W> Failed to initialize device 10-0 [0008.149] E> NVME (0) boot failed, err: 0x80800612 [0008.154] I> ########## NVME (1) boot ########## [0008.158] I> Initializing nvme device instance 1 [0008.163] I> Initializing nvme controller [0008.167] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14100000 [0008.173] I> vpcie3v3-supply not found [0008.176] I> vpcie12v-supply not found [0008.180] W> Failed to get nvidia,plat-gpios [0008.184] I> tegrabl_pcie_soc_preinit: (1): [0008.188] I> Unpowergate [0008.191] I> tegrabl_car_clk_disable(1) ... [0008.195] I> tegrabl_car_rst_set(CORE, 1) ... [0008.199] I> tegrabl_car_rst_set(APB, 1) ... [0008.203] I> tegrabl_car_clk_enable(1) ... [0008.207] I> tegrabl_car_rst_clear(APB, 1) ... [0008.211] I> tegrabl_set_ctrl_state(1) [0008.215] I> CLR PCIE_APB:6 [0008.217] I> tegrabl_pcie_soc_init: (1): [0008.221] I> APPL initialization ... [0008.224] I> poweron phys [0008.227] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14100000 [0008.233] I> tegrabl_power_on_phy: power on phy @0x3e10000 [0008.340] I> PCIe controller-1 link is up [0008.341] I> tegra_pcie_info[1].cfg0_base = 0x30000000 [0008.341] I> tegra_pcie_info[1].cfg1_base = 0x30020000 [0008.341] I> tegra_pcie_info[1].atu_dma_base = 0x30040000 [0008.342] I> tegra_pcie_bus[1].mem = 0x30200000 [0008.342] I> Scanning busnr: 0 devfn: 0 [0008.342] I> PCIe IDs: 0x1ad210de [0008.345] I> PCIe RID_CC: 0x60400a1 [0008.349] I> Scanning busnr: 1 devfn: 0 [0008.352] I> PCIe IDs: 0x91711b4b [0008.356] I> PCIe RID_CC: 0x1060113 [0008.359] I> PCI Config: I/O=0x30100000, Memory=0x30200000 [0008.364] I> IO bar_num=0 bar=0x30100000 [0008.368] I> IO bar_num=1 bar=0x30100008 [0008.372] I> IO bar_num=2 bar=0x30100010 [0008.376] I> IO bar_num=3 bar=0x30100018 [0008.379] I> IO bar_num=4 bar=0x30100020 [0008.383] I> MEM bar_num=5 bar=0x30200000 [0008.387] I> Number of PCIe devices detected: 2 [0008.391] E> tegrabl_nvme_init: Failed tegrabl_pcie_get_dev(1); error=0x0 [0008.398] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800612 [0008.404] W> Failed to open NVME-1, err = 80800612 [0008.409] W> Failed to initialize device 10-1 [0008.413] E> NVME (1) boot failed, err: 0x80800612 [0008.418] I> ########## NVME (2) boot ########## [0008.422] I> Initializing nvme device instance 2 [0008.427] I> Initializing nvme controller [0008.431] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14120000 [0008.437] I> vpcie3v3-supply not found [0008.441] I> vpcie12v-supply not found [0008.444] W> Failed to get nvidia,plat-gpios [0008.448] I> tegrabl_pcie_soc_preinit: (2): [0008.452] I> Unpowergate [0008.455] I> tegrabl_car_clk_disable(2) ... [0008.459] I> tegrabl_car_rst_set(CORE, 2) ... [0008.463] I> tegrabl_car_rst_set(APB, 2) ... [0008.467] I> tegrabl_car_clk_enable(2) ... [0008.471] I> tegrabl_car_rst_clear(APB, 2) ... [0008.475] I> tegrabl_set_ctrl_state(2) [0008.479] I> CLR PCIE_APB:6 [0008.482] I> tegrabl_pcie_soc_init: (2): [0008.485] I> APPL initialization ... [0008.489] I> poweron phys [0008.492] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14120000 [0008.498] I> tegrabl_power_on_phy: controller 2 not available [0008.503] E> Failed to power on phy on controller-2 [0008.508] W> Failed tegrabl_pcie_soc_init(), error=0x1 [0008.513] I> Failed to initialize SoC Host PCIe controller [0008.518] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(2); error=0x1 [0008.525] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800601 [0008.531] W> Failed to open NVME-2, err = 80800601 [0008.536] W> Failed to initialize device 10-2 [0008.540] E> NVME (2) boot failed, err: 0x80800601 [0008.545] I> ########## NVME (3) boot ########## [0008.549] I> Initializing nvme device instance 3 [0008.553] I> Initializing nvme controller [0008.558] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14140000 [0008.564] I> vpcie3v3-supply not found [0008.567] I> vpcie12v-supply not found [0008.571] W> Failed to get nvidia,plat-gpios [0008.575] I> tegrabl_pcie_soc_preinit: (3): [0008.579] I> Unpowergate [0008.582] I> tegrabl_car_clk_disable(3) ... [0008.585] I> tegrabl_car_rst_set(CORE, 3) ... [0008.590] I> tegrabl_car_rst_set(APB, 3) ... [0008.594] I> tegrabl_car_clk_enable(3) ... [0008.598] I> tegrabl_car_rst_clear(APB, 3) ... [0008.602] I> tegrabl_set_ctrl_state(3) [0008.606] I> CLR PCIE_APB:6 [0008.608] I> tegrabl_pcie_soc_init: (3): [0008.612] I> APPL initialization ... [0008.615] I> poweron phys [0008.618] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14140000 [0008.624] I> tegrabl_power_on_phy: power on phy @0x3e80000 [0009.730] C> Failed to link up controller-3 [0009.730] W> Failed tegrabl_pcie_soc_init(), error=0x12 [0009.731] I> Failed to initialize SoC Host PCIe controller [0009.731] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(3); error=0x12 [0009.732] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800612 [0009.732] W> Failed to open NVME-3, err = 80800612 [0009.737] W> Failed to initialize device 10-3 [0009.741] E> NVME (3) boot failed, err: 0x80800612 [0009.745] I> ########## NVME (4) boot ########## [0009.750] I> Initializing nvme device instance 4 [0009.754] I> Initializing nvme controller [0009.759] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14160000 [0009.765] I> vpcie3v3-supply not found [0009.768] I> vpcie12v-supply not found [0009.772] W> Failed to get nvidia,plat-gpios [0009.776] I> tegrabl_pcie_soc_preinit: (4): [0009.780] I> Unpowergate [0009.783] I> tegrabl_car_clk_disable(4) ... [0009.786] I> tegrabl_car_rst_set(CORE, 4) ... [0009.791] I> tegrabl_car_rst_set(APB, 4) ... [0009.795] I> tegrabl_car_clk_enable(4) ... [0009.799] I> tegrabl_car_rst_clear(APB, 4) ... [0009.803] I> tegrabl_set_ctrl_state(4) [0009.807] I> CLR PCIE_APB:6 [0009.809] I> tegrabl_pcie_soc_init: (4): [0009.813] I> APPL initialization ... [0009.816] I> poweron phys [0009.819] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x14160000 [0009.825] I> tegrabl_power_on_phy: controller 4 not available [0009.831] E> Failed to power on phy on controller-4 [0009.836] W> Failed tegrabl_pcie_soc_init(), error=0x1 [0009.840] I> Failed to initialize SoC Host PCIe controller [0009.846] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(4); error=0x1 [0009.852] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800601 [0009.859] W> Failed to open NVME-4, err = 80800601 [0009.863] W> Failed to initialize device 10-4 [0009.867] E> NVME (4) boot failed, err: 0x80800601 [0009.872] I> ########## NVME (5) boot ########## [0009.877] I> Initializing nvme device instance 5 [0009.881] I> Initializing nvme controller [0009.885] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x141a0000 [0009.891] I> i=0, reg_phandle=0x1b [0009.897] I> reg_voltage=3300000 [0009.898] I> tegrabl_pcie_enable_regulators: regulator_set_voltage(0x1b, 3300000) [0009.909] I> enabling 'vdd-3v3-pcie' regulator [0009.909] I> i=1, reg_phandle=0x1c [0009.914] I> reg_voltage=1200000 [0009.915] I> tegrabl_pcie_enable_regulators: regulator_set_voltage(0x1c, 1200000) [0009.927] I> enabling 'vdd-12v-pcie' regulator [0009.927] I> tegrabl_pcie_soc_preinit: (5): [0009.931] I> Unpowergate [0009.934] I> tegrabl_car_clk_disable(5) ... [0009.938] I> tegrabl_car_rst_set(CORE, 5) ... [0009.942] I> tegrabl_car_rst_set(APB, 5) ... [0009.946] I> tegrabl_car_clk_enable(5) ... [0009.950] I> tegrabl_car_rst_clear(APB, 5) ... [0009.954] I> tegrabl_set_ctrl_state(5) [0009.958] I> CLR PCIE_APB:6 [0009.960] I> tegrabl_pcie_soc_init: (5): [0009.964] I> APPL initialization ... [0009.967] I> poweron phys [0009.971] I> tegrabl_locate_pcie_ctrl_in_dt: found match at 0x141a0000 [0009.976] I> tegrabl_power_on_phy: controller 5 not available [0009.982] E> Failed to power on phy on controller-5 [0009.987] W> Failed tegrabl_pcie_soc_init(), error=0x1 [0009.992] I> Failed to initialize SoC Host PCIe controller [0009.997] E> tegrabl_nvme_init: Failed tegrabl_pcie_init(5); error=0x1 [0010.003] W> tegrabl_nvme_bdev_open: Failed NVME INIT; error=0x80800601 [0010.010] W> Failed to open NVME-5, err = 80800601 [0010.014] W> Failed to initialize device 10-5 [0010.019] E> NVME (5) boot failed, err: 0x80800601 [0010.023] I> ########## Fixed storage boot ########## [0010.028] I> Loading kernel-bootctrl from partition [0010.033] I> Loading partition kernel-bootctrl at 0xa4470000 from device(0x1) [0010.046] W> tegrabl_get_kernel_bootctrl: magic number(0x00000000) is invalid [0010.047] W> tegrabl_get_kernel_bootctrl: use default dummy boot control data [0010.060] I> Already published: 00010003 [0010.060] I> Look for boot partition [0010.061] I> Fallback: assuming 0th partition is boot partition [0010.067] I> Detect filesystem [0010.094] I> Loading extlinux.conf ... [0010.094] I> Loading extlinux.conf binary from rootfs ... [0010.095] I> rootfs path: /sdmmc_user/boot/extlinux/extlinux.conf [0010.144] I> Loading extlinux.conf sig file from rootfs ... [0010.144] I> rootfs path: /sdmmc_user/boot/extlinux/extlinux.conf.sig [0010.175] I> Validate extlinux.conf ... [0010.175] I> T19x: Authenticate extlinux.conf (bin_type: 54), max size 0x2000 [0010.176] E> digest on binary did not match!! [0010.176] C> OEM authentication of extlinux.conf payload failed! [0010.176] W> Failed to validate extlinux.conf binary from rootfs (err=1077936152, fail=0) [0010.179] W> Security fuse not burned, ignore validation failure [0010.184] I> restore load_size to 858 [0010.188] I> L4T boot options [0010.191] I> [1]: "primary kernel" [0010.194] I> Enter choice: [0013.197] I> Continuing with default option: 1 [0013.197] I> Loading kernel ... [0013.197] I> Loading kernel binary from rootfs ... [0013.198] I> rootfs path: /sdmmc_user/boot/Image [0013.442] I> Loading kernel sig file from rootfs ... [0013.442] I> rootfs path: /sdmmc_user/boot/Image.sig [0013.473] I> overload load_size to 34484232 (from 34615304) [0013.474] I> Validate kernel ... [0013.474] I> T19x: Authenticate kernel (bin_type: 37), max size 0x5000000 [0013.788] E> digest on binary did not match!! [0013.788] C> OEM authentication of kernel payload failed! [0013.789] W> Failed to validate kernel binary from rootfs (err=1077936152, fail=0) [0013.789] W> Security fuse not burned, ignore validation failure [0013.790] I> restore load_size to 34615304 [0013.807] I> Loading kernel-dtb ... [0013.807] I> No kernel-dtb binary path [0013.807] I> Continue to load from partition ... [0013.808] W> No valid slot number is found in scratch register [0013.808] W> Return default slot: _a [0013.810] I> A/B: bin_type (38) slot 0 [0013.814] I> Loading kernel-dtb from partition [0013.818] I> Loading partition kernel-dtb at 0x91000000 from device(0x1) [0013.834] I> Validate kernel-dtb ... [0013.834] I> T19x: Authenticate kernel-dtb (bin_type: 38), max size 0x400000 [0013.837] I> Encryption fuse is not ON [0013.840] I> Loading ramdisk from rootfs ... [0013.842] I> Loading ramdisk binary from rootfs ... [0013.847] I> rootfs path: /sdmmc_user/boot/initrd [0013.922] I> Loading ramdisk sig file from rootfs ... [0013.922] I> rootfs path: /sdmmc_user/boot/initrd.sig [0013.953] I> overload load_size to 7238344 (from 7238352) [0013.953] I> Validate ramdisk ... [0013.953] I> T19x: Authenticate ramdisk (bin_type: 54), max size 0x4000000 [0014.020] I> Encryption fuse is not ON [0014.037] I> Kernel hdr @0xa4470000 [0014.037] I> Kernel dtb @0x90000000 [0014.037] I> decompressor handler not found [0014.038] I> Copying kernel image (34615304 bytes) from 0xa4470000 to 0x80080000 ... [0014.048] I> Done [0014.049] I> Updated bpmp info to DTB [0014.050] I> Ramdisk: Base: 0x92000000; Size: 0x6e72c8 [0014.051] I> Updated initrd info to DTB [0014.051] W> WARN: Fail to override "console=none" in commandline [0014.051] I> Active rootfs suffix: [0014.053] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0014.061] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0014.068] W> No valid slot number is found in scratch register [0014.074] W> Return default slot: _a [0014.077] I> Active slot suffix: [0014.080] I> add_boot_slot_suffix: slot_suffix = [0014.085] I> Linux Cmdline: console=ttyTCU0,115200 video=tegrafb earlycon=tegra_comb_uart,mmio32,0x0c168000 gpt rootfs.slot_suffix= tegra_fbmem=0x140000@0xa06aa000 lut_mem=0x2008@0xa06a4000 usbcore.old_scheme_first=1 tegraid=19.1.2.0.0 maxcpus=8 boot.slot_suffix= boot.ratchetvalues=0.4.2 vpr_resize sdhci_tegra.en_boot_part_access=1 [0014.114] I> Updated bootarg info to DTB [0014.118] W> MAC addr invalid! [0014.121] E> Failed to get WIFI MAC address [0014.125] W> MAC addr invalid! [0014.128] E> Failed to get Bluetooth MAC address [0014.132] I> eeprom_get_mac_addr: MAC (type: 2): 48:b0:2d:2b:6f:0b [0014.139] W> "plugin-manager" doesn't exist, creating [0014.143] I> Adding /chosen/plugin-manager/cvm [0014.147] W> "chip-id" doesn't exist, creating [0014.152] I> Adding /chosen/plugin-manager/chip-id [0014.156] W> "configs" doesn't exist, creating [0014.161] I> Adding /chosen/plugin-manager/configs [0014.165] W> "ids" doesn't exist, creating [0014.169] I> Adding /chosen/plugin-manager/ids [0014.174] W> "odm-data" doesn't exist, creating [0014.178] I> Adding /chosen/plugin-manager/odm-data [0014.185] W> "memory" doesn't exist, creating [0014.187] I> [0] START: 0x80000000, END: 0xac000000 [0014.191] I> [1] START: 0xac004000, END: 0xf0ad0000 [0014.196] I> [2] START: 0xf0adc000, END: 0xf0ae0000 [0014.201] I> dram_block larger than 80000000 [0014.205] I> [3] START: 0x100000000, END: 0x880000000 [0014.210] I> added [base:0x80000000, size:0x2c000000] to /memory [0014.216] I> added [base:0xac200000, size:0x44800000] to /memory [0014.222] I> added [base:0x100000000, size:0x780000000] to /memory [0014.229] I> Updated memory info to DTB [0014.232] E> add_disp_param: failed to get display params for du=1 [0014.238] W> "reset" doesn't exist, creating [0014.242] I> Adding ecid(00000001647c18802000000017030140) to DT [0014.248] I> NVG: Logical CPU: 0; MPIDR: 0x80000000 [0014.252] I> NVG: Logical CPU: 1; MPIDR: 0x80000001 [0014.257] I> NVG: Logical CPU: 2; MPIDR: 0x80000100 [0014.262] I> NVG: Logical CPU: 3; MPIDR: 0x80000101 [0014.266] I> NVG: Logical CPU: 4; MPIDR: 0x80000200 [0014.271] I> NVG: Logical CPU: 5; MPIDR: 0x80000201 [0014.276] I> NVG: Logical CPU: 6; MPIDR: 0x80000300 [0014.280] I> NVG: Logical CPU: 7; MPIDR: 0x80000301 [0014.286] W> "misc-data" doesn't exist, creating [0014.290] I> Boot-device: eMMC [0014.293] I> Add boot-sdmmc to plugin-manager/misc-data [0014.298] I> Add storage-sdmmc to plugin-manager/misc-data [0014.303] W> Unknown storage device [0014.307] I> Add serial number:1424220044470 as DT property [0014.313] I> Plugin-manager override starting [0014.316] I> node /plugin-manager/fragement-tegra-wdt-en matches [0014.323] I> node /plugin-manager/fragement-soft-wdt matches [0014.331] I> node /plugin-manager/fragment-pcie-c5-ep matches [0014.335] I> node /plugin-manager/fragment-tegra-ufs-lane10 matches [0014.347] I> Disable plugin-manager status in FDT [0014.348] I> Plugin-manager override finished successfully [0014.349] I> tegrabl_load_kernel_and_dtb: Done [0014.359] I> Kernel EP: 0x80080000, DTB: 0x90000000 [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.253 (root@ubuntu-jetson) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #4 SMP PREEMPT Wed Oct 6 13:15:30 BST 2021 [ 0.000000] Boot CPU: AArch64 Processor [4e0f0040] [ 0.000000] OF: fdt:memory scan node memory, reg size 48, [ 0.000000] OF: fdt: - 80000000 , 2c000000 [ 0.000000] OF: fdt: - ac200000 , 44800000 [ 0.000000] OF: fdt: - 100000000 , 780000000 [ 0.000000] earlycon: tegra_comb_uart0 at MMIO32 0x000000000c168000 (options '') [ 0.000000] bootconsole [tegra_comb_uart0] enabled [ 0.000000] Found tegra_fbmem: 00140000@a06aa000 [ 0.000000] Found lut_mem: 00002008@a06a4000 [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node grid-of-semaphores, compatible id nvidia,gosmem [ 0.000000] cma: Reserved 64 MiB at 0x00000000c2000000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57624 r8192 d32488 u98304 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8194218 [ 0.000000] Kernel command line: console=ttyTCU0,115200 video=tegrafb earlycon=tegra_comb_uart,mmio32,0x0c168000 gpt rootfs.slot_suffix= tegra_fbmem=0x140000@0xa06aa000 lut_mem=0x2008@0xa06a4000 usbcore.old_scheme_first=1 tegraid=19.1.2.0.0 maxcpus=8 boot.slot_suffix= boot.ratchetvalues=0.4.2 vpr_resize sdhci_tegra.en_boot_part_access=1 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyTCU0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 rootfstype=ext4 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 229376 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 262144 bytes [ 0.000000] early log buf free: 29964(91%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 4194304 (order: 13, 33554432 bytes) [ 0.000000] Inode-cache hash table entries: 2097152 (order: 12, 16777216 bytes) [ 0.000000] Memory: 31924076K/33297140K available (15358K kernel code, 2956K rwdata, 6824K rodata, 8640K init, 612K bss, 619400K reserved, 753664K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f80000 ( 15360 KB) [ 0.000000] .rodata : 0xffffff8008f80000 - 0xffffff8009630000 ( 6848 KB) [ 0.000000] .init : 0xffffff8009630000 - 0xffffff8009ea0000 ( 8640 KB) [ 0.000000] .data : 0xffffff8009ea0000 - 0xffffff800a183008 ( 2957 KB) [ 0.000000] .bss : 0xffffff800a183008 - 0xffffff800a21c0b4 ( 613 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf20000000 ( 512 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc800000000 ( 32768 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout