[0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de)
[0000.130] Processing in cold boot mode Bootloader 2
[0000.135] A02 Bootrom Patch rev = 1023
[0000.138] Power-up reason: pmc por
[0000.141] No Battery Present
[0000.144] pmic max77620 reset reason
[0000.147] pmic max77620 NVERC : 0x40
[0000.151] RamCode = 0
[0000.153] Platform has DDR4 type RAM
[0000.156] max77620 disabling SD1 Remote Sense
[0000.161] Setting DDR voltage to 1125mv
[0000.165] Serial Number of Pmic Max77663: 0x802a4
[0000.172] Entering ramdump check
[0000.175] Get RamDumpCarveOut = 0x0
[0000.178] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0000.184] Last reboot was clean, booting normally!
[0000.188] Sdram initialization is successful 
[0000.192] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.198] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.204] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.210] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.233] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.256] Platform-DebugCarveout: 0
[0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.265] Non secure mode, and RB not enabled.
[0000.269] BoardID = 3448, SKU = 0x0
[0000.272] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.276] Nano-SD: checking PT table on QSPI ...
[0000.280] Read PT from (2:0)
[0000.296] Using BFS PT to query partitions 
[0000.301] Loading Tboot-CPU binary
[0000.330] Verifying TBC in OdmNonSecureSBK mode
[0000.340] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.347] Bootloader downloaded successfully.
[0000.351] Downloaded Tboot-CPU binary to 0xa0000258
[0000.356] MAX77620_GPIO5 configured
[0000.359] CPU power rail is up
[0000.362] CPU clock enabled
[0000.366] Performing RAM repair
[0000.369] Updating A64 Warmreset Address to 0xa00002e9
[0000.374] BoardID = 3448, SKU = 0x0
[0000.377] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.381] Nano-SD: checking PT table on QSPI ...
[0000.385] Loading NvTbootBootloaderDTB
[0000.452] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0000.525] Bootloader DTB Load Address: 0x83000000
[0000.530] BoardID = 3448, SKU = 0x0
[0000.533] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.537] Nano-SD: checking PT table on QSPI ...
[0000.541] Loading NvTbootKernelDTB
[0000.607] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0000.680] Kernel DTB Load Address: 0x83100000
[0000.684] BoardID = 3448, SKU = 0x0
[0000.688] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.691] Nano-SD: checking PT table on QSPI ...
[0000.698] Loading cboot binary
[0000.813] Verifying EBT in OdmNonSecureSBK mode
[0000.855] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0000.862] Bootloader downloaded successfully.
[0000.866] BoardID = 3448, SKU = 0x0
[0000.870] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.873] Nano-SD: checking PT table on QSPI ...
[0000.878] PT: Partition NCT NOT found ! 
[0000.882] Warning: Find Partition via PT Failed
[0000.886] Next binary entry address: 0x92c00258 
[0000.891] BoardId: 3448
[0000.895] Overriding pmu board id with proc board id
[0000.900] Display board id is not available 
[0000.904] BoardID = 3448, SKU = 0x0
[0000.907] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.911] Nano-SD: checking PT table on QSPI ...
[0001.016] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0001.073] /bpmp deleted
[0001.075] SC7EntryFw header found loaded at 0xff700000
[0001.271] OVR2 PMIC
[0001.272] Bpmp FW successfully loaded
[0001.276] BoardID = 3448, SKU = 0x0
[0001.279] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0001.283] Nano-SD: checking PT table on QSPI ...
[0001.288] WB0 init successfully at 0xff780000
[0001.293] Set NvDecSticky Bits
[0001.296] GSC2 address ff53fffc value c0edbbcc
[0001.302] GSC MC Settings done
[0001.305] BoardID = 3448, SKU = 0x0
[0001.309] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0001.312] Nano-SD: checking PT table on QSPI ...
[0001.318] TOS Image length 53680
[0001.321]  Monitor size 53680
[0001.324]  OS size 0
[0001.339] Secure Os AES-CMAC Verification Success!
[0001.343] TOS image cipher info: plaintext
[0001.347] Loading and Validation of Secure OS Successful
[0001.363] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.368] NvTbootPackSdramParams: start. 
[0001.373] NvTbootPackSdramParams: done. 
[0001.377] Tegraboot started after 51843 us
[0001.381] Basic modules init took 886386 us
[0001.385] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB
[0001.390] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0001.396] Next stage binary read took 102859 us
[0001.400] Carveout took -126356 us
[0001.403] CPU initialization took 495394 us
[0001.407] Total time taken by TegraBoot 1358283 us

[0001.412] Starting CPU & Halting co-processor 

64NOTICE:  BL31: v1.3(release):5b49e7f80
NOTICE:  BL31: Built : 08:37:40, Feb 19 2021
ERROR:   Error initializing runtime service trusty_fast
[0001.534] RamCode = 0
[0001.539] LPDDR4 Training: Read DT: Number of tables = 2
[0001.544] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0001.557] EMC Training Successful
[0001.560] 408000 not found in DVFS table
[0001.566] RamCode = 0
[0001.570] DT Write: emc-table@204000 succeeded
[0001.575] DT Write: emc-table@1600000 succeeded
[0001.579] LPDDR4 Training: Write DT: Number of tables = 2
[0001.626] 
[0001.627] Debug Init done
[0001.630] Marked DTB cacheable
[0001.633] Bootloader DTB loaded at 0x83000000
[0001.638] Marked DTB cacheable
[0001.640] Kernel DTB loaded at 0x83100000
[0001.644] DeviceTree Init done
[0001.657] Pinmux applied successfully
[0001.662] gicd_base: 0x50041000
[0001.665] gicc_base: 0x50042000
[0001.668] Interrupts Init done
[0001.672] Using base:0x60005090 & irq:208 for tick-timer
[0001.677] Using base:0x60005098 for delay-timer
[0001.682] platform_init_timer: DONE
[0001.685] Timer(tick) Init done
[0001.689] osc freq = 38400 khz
[0001.693] 
[0001.694] Welcome to L4T Cboot
[0001.697] 
[0001.698] Cboot Version: 00.00.2018.01-t210-39562017
[0001.703] calling constructors
[0001.706] initializing heap
[0001.709] initializing threads
[0001.712] initializing timers
[0001.715] creating bootstrap completion thread
[0001.719] top of bootstrap2()
[0001.722] CPU: ARM Cortex A57
[0001.725] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0001.729] initializing platform
[0001.737] Manufacturer: MF = 0xc2, ID MSB = 0x25
[0001.742] ID LSB = 0x36, ID-CFI len = 194 bytes
[0001.746] Macronix QSPI chip present
[0001.750] SPI device register
[0001.752] init boot device
[0001.755] allocating memory for boot device(SPI)
[0001.760] registering boot device
[0001.768] QSPI bdev is already initialized
[0001.772] Enable APE clock
[0001.775] Un-powergate APE partition
[0001.778] of_register: registering tegra_udc to of_hal
[0001.783] of_register: registering inv20628-driver to of_hal
[0001.789] of_register: registering ads1015-driver to of_hal
[0001.794] of_register: registering lp8557-bl-driver to of_hal
[0001.800] of_register: registering bq2419x_charger to of_hal
[0001.806] of_register: registering bq27441_fuel_gauge to of_hal
[0001.817] gpio framework initialized
[0001.821] of_register: registering tca9539_gpio to of_hal
[0001.826] of_register: registering tca9539_gpio to of_hal
[0001.831] of_register: registering i2c_bus_driver to of_hal
[0001.837] of_register: registering i2c_bus_driver to of_hal
[0001.843] of_register: registering i2c_bus_driver to of_hal
[0001.848] pmic framework initialized
[0001.852] of_register: registering max77620_pmic to of_hal
[0001.857] regulator framework initialized
[0001.861] of_register: registering tps65132_bl_driver to of_hal
[0001.867] initializing target
[0001.873] gpio_driver_register: register 'tegra_gpio_driver' driver
[0001.881] board ID = D78, board SKU = 0
[0001.885] Skipping Z3!
[0001.889] fixed regulator driver initialized
[0001.907] initializing OF layer
[0001.910] NCK carveout not present
[0001.914] Skipping dts_overrides
[0001.918] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.935] I2C Bus Init done
[0001.937] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.948] I2C Bus Init done
[0001.950] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.961] I2C Bus Init done
[0001.963] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.974] I2C Bus Init done
[0001.976] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.987] I2C Bus Init done
[0001.990] of_children_init: Ops found for compatible string maxim,max77620
[0002.000] max77620_init using irq 118
[0002.005] register 'maxim,max77620' pmic
[0002.009] gpio_driver_register: register 'max77620-gpio' driver
[0002.015] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.026] I2C Bus Init done
[0002.029] NCK carveout not present
[0002.039] Find /i2c@7000c000's alias i2c0
[0002.043] get eeprom at 1-a0, size 256, type 0
[0002.052] Find /i2c@7000c500's alias i2c2
[0002.056] get eeprom at 3-a0, size 256, type 0
[0002.060] get eeprom at 3-ae, size 256, type 0
[0002.065] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.070] I2C slave not started
[0002.073] I2C write failed
[0002.076] Writing offset failed
[0002.079] eeprom_init: EEPROM read failed
[0002.083] pm_ids_update: eeprom init failed
[0002.087] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.117] pm_ids_update: The pm board id is 3448-0000-400
[0002.124] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50
[0002.132] pm_ids_update: pm id update successful
[0002.137] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.167] pm_ids_update: The pm board id is 3449-0000-400
[0002.173] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57
[0002.181] pm_ids_update: pm id update successful
[0002.211] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.217] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0002.225] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.231] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0002.239] updating /chosen/nvidia,ethernet-mac node 00:04:4b:eb:f1:a1
[0002.245] Plugin Manager: Parse ODM data 0x000a4000
[0002.258] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 
[0002.273] Find /i2c@7000c000's alias i2c0
[0002.277] get eeprom at 1-a0, size 256, type 0
[0002.285] Find /i2c@7000c500's alias i2c2
[0002.289] get eeprom at 3-a0, size 256, type 0
[0002.294] get eeprom at 3-ae, size 256, type 0
[0002.298] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.303] I2C slave not started
[0002.306] I2C write failed
[0002.309] Writing offset failed
[0002.312] eeprom_init: EEPROM read failed
[0002.316] pm_ids_update: eeprom init failed
[0002.320] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.350] pm_ids_update: The pm board id is 3448-0000-400
[0002.356] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50
[0002.363] pm_ids_update: pm id update successful
[0002.368] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.398] pm_ids_update: The pm board id is 3449-0000-400
[0002.404] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57
[0002.411] pm_ids_update: pm id update successful
[0002.442] Add serial number:1423119020987 as DT property
[0002.449] Applying platform configs
[0002.456] platform-init is not present. Skipping
[0002.461] calling apps_init()
[0002.466] Couldn't find GPT header
[0002.471] Proceeding to Cold Boot
[0002.474] starting app android_boot_app
[0002.478] Device state: unlocked
[0002.481] display console init
[0002.489] could not find regulator
[0002.493] hdmi cable connected
[0002.508] edid read success
[0002.523] edidDT entry for leds-pwm not found
 [0002.531] read success
[0002.533] width = 640, height = 480, frequency = 25174825
[0002.539] width = 1920, height = 1080, frequency = 148500000
[0002.544] width = 1920, height = 540, frequency = 74250000
[0002.550] width = 1920, height = 1080, frequency = 148351648
[0002.555] width = 1920, height = 1080, frequency = 148351648
[0002.561] width = 1280, height = 720, frequency = 74175824
[0002.566] width = 1280, height = 720, frequency = 74175824
[0002.572] width = 720, height = 480, frequency = 26973026
[0002.577] width = 720, height = 576, frequency = 26973026
[0002.583] width = 720, height = 480, frequency = 26973026
[0002.588] width = 720, height = 576, frequency = 26973026
[0002.593] Best mode Width = 1920, Height = 1080, freq = 148351648
[0002.601] tmds-config node not found
[0002.605] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts
[0002.620] setting 'vdd-1v8' regulator to 1800000 micro volts
[0002.628] could not find regulator
[0002.631] could not find regulator
[0002.634] could not find regulator
[0002.663] using default cmu settings
[0002.666] dc_hdmi_enable, starting HDMI initialisation
[0002.672] dc_hdmi_enable, HDMI initialisation complete
[0002.677] list and configure display window
[0002.686] display console init completed
[0002.697] subnode volume_up is not found !
[0002.701] subnode back is not found !
[0002.705] subnode volume_down is not found !
[0002.709] subnode menu is not found !
[0002.713] Gpio keyboard init success
[0002.793] found decompressor handler: lz4-legacy
[0002.808] decompressing blob (type 1)...
[0002.878] load_bmp_blob: panelresolution=1080 type=3
[0002.952] decompressor handler not found
[0002.956] load_firmware_blob: Firmware blob loaded, entries=2
[0002.962] XUSB blob version 0 size 124416 @ 0x934ae28c
[0002.968] -------> se_aes_verify_sbk_clear: 747
[0002.972] se_aes_verify_sbk_clear: Error
[0002.976] SE operation failed
[0002.979] bl_battery_charging: connected to external power supply
[0002.991] device_query_partition_size: failed to open partition spiflash0:MSC !
[0002.998] MSC Partition not found
[0003.005] device_query_partition_size: failed to open partition spiflash0:USP !
[0003.012] USP partition read failed!
[0003.015] blob_init: blob-partition USP header read failed
[0003.021] android_boot Unable to update recovery partition
[0003.026] kfs_getpartname: name = LNX
[0003.030] Loading kernel from LNX
[0003.039] Found 19 BFS partitions in "spiflash0"
[0003.362] load kernel from storage
[0003.367] decompressor handler not found
[0003.635] Successfully loaded kernel and ramdisk images
[0003.640] board ID = D78, board SKU = 0
[0003.645] sdmmc node status = okay
[0003.648] sdcard instance = 0
[0003.651] sdcard gpio handle 0x5b
[0003.654] sdcard gpio pin 0xc9
[0003.657] sdcard gpio flags 0x0
[0003.660] vmmc-supply 0x9e
[0003.663] cd_gpio_pin = 201
[0003.666] pin_state = 1
[0003.668] No sdcard
[0003.670] SD-card NOT present ...
[0003.673] load_and_boot_kernel: SD card not detected!
[0003.679] load_bmp_blob: panelresolution=1080 type=3
[0004.175] display bmp image done
[0009.179] load_bmp_blob: panelresolution=1080 type=3
[0009.673] display bmp image done
[0009.676] NCK carveout not present
[0009.679] Skipping dts_overrides
[0009.682] NCK carveout not present
[0009.692] Find /i2c@7000c000's alias i2c0
[0009.696] get eeprom at 1-a0, size 256, type 0
[0009.705] Find /i2c@7000c500's alias i2c2
[0009.709] get eeprom at 3-a0, size 256, type 0
[0009.713] get eeprom at 3-ae, size 256, type 0
[0009.717] pm_ids_update: Updating 1,a0, size 256, type 0
[0009.723] I2C slave not started
[0009.726] I2C write failed
[0009.728] Writing offset failed
[0009.731] eeprom_init: EEPROM read failed
[0009.735] pm_ids_update: eeprom init failed
[0009.739] pm_ids_update: Updating 3,a0, size 256, type 0
[0009.770] pm_ids_update: The pm board id is 3448-0000-400
[0009.776] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50
[0009.785] pm_ids_update: pm id update successful
[0009.789] pm_ids_update: Updating 3,ae, size 256, type 0
[0009.819] pm_ids_update: The pm board id is 3449-0000-400
[0009.826] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57
[0009.834] pm_ids_update: pm id update successful
[0009.864] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0009.870] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0009.878] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0009.884] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0009.892] updating /chosen/nvidia,ethernet-mac node 00:04:4b:eb:f1:a1
[0009.898] Plugin Manager: Parse ODM data 0x000a4000
[0009.911] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 
[0009.919] Add serial number:1423119020987 as DT property
[0009.928] "bpmp" doesn't exist, creating 
[0009.934] Updated bpmp info to DTB
[0009.938] Updated initrd info to DTB
[0009.942] "proc-board" doesn't exist, creating 
[0009.948] Updated board info to DTB
[0009.951] "pmu-board" doesn't exist, creating 
[0009.957] Updated board info to DTB
[0009.961] "display-board" doesn't exist, creating 
[0009.967] Updated board info to DTB
[0009.970] "reset" doesn't exist, creating 
[0009.975] Updated reset info to DTB
[0009.978] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 
[0010.017] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 
[0010.023] boot image cmdline: root=/dev/sda1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 
[0010.036] Updated bootarg info to DTB
[0010.040] Adding uuid 00000001644577861400000018040140 to DT
[0010.045] Adding eks info 0 to DT
[0010.051] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7
[0010.057] Updated memory info to DTB
[0010.065] set vdd_core voltage to 1075 mv
[0010.069] setting 'vdd-core' regulator to 1075000 micro volts
[0010.075] Found secure-pmc; disable BPMP


U-Boot 2020.04-g6b630d64fd (Feb 19 2021 - 08:37:46 -0800)

SoC: tegra210
Model: NVIDIA Jetson Nano Developer Kit
Board: NVIDIA P3450-0000
DRAM:  4 GiB
MMC:   sdhci@700b0000: 1, sdhci@700b0600: 0
Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  2  1  0 
MMC: no card present
Card did not respond to voltage select!
starting USB...
Bus usb@7d000000: tegrausb: Invalid dr_mode 2 for host mode
probe failed, error -1
Bus xusb@70090000: 
Firmware size 124416
Firmware timestamp: 0x5da88fc3, Version: 50.25 release

Register HCSParams1: 9000124 NbrPorts: 9
Starting the controller
USB XHCI 1.00
scanning bus xusb@70090000 for devices... 6 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found

Device 0: Vendor: STT      Rev: 1100 Prod: USB_ST12KS      
            Type: Removable Hard Disk
            Capacity: 30526.0 MB = 29.8 GB (62517248 x 512)
... is now current device
Scanning usb 0:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
728 bytes read in 10 ms (70.3 KiB/s)
1:	primary kernel
Retrieving file: /boot/initrd
7159841 bytes read in 69 ms (99 MiB/s)
Retrieving file: /boot/Image
12582912 bytes read in 115 ms (104.3 MiB/s)
append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1  earlycon=uart8250,mmio32,0x70006000  root=/dev/sda1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
## Flattened Device Tree blob at 83100000
   Booting using the fdt blob at 0x83100000
ERROR: reserving fdt memory region failed (addr=0 size=0)
ERROR: reserving fdt memory region failed (addr=0 size=0)
   Using Device Tree in place at 0000000083100000, end 000000008317e68d
copying carveout for /host1x@50000000/dc@54200000...
copying carveout for /host1x@50000000/dc@54240000...

Starting kernel ...

"Synchronous Abort" handler, esr 0x02000000
elr: 0000000006951000 lr : 00000000800827b8 (reloc)
elr: 0000000085600000 lr : 00000000fed317b8
x0 : 0000000083100000 x1 : 0000000000000000
x2 : 0000000000000000 x3 : 0000000000000000
x4 : 0000000084080000 x5 : 0000000000000001
x6 : 0000000000000008 x7 : 0000000000000000
x8 : 00000000fc84e790 x9 : 0000000001008000
x10: 000000000a200023 x11: 0000000000000002
x12: 0000000000000002 x13: 000000000001da08
x14: 00000000fc5f7358 x15: 00000000fed30b3c
x16: 0000000000000001 x17: 0000000000000040
x18: 00000000fc5ffdc0 x19: 00000000fedcbf60
x20: 0000000000000000 x21: 0000000000000000
x22: 0000000000000003 x23: 00000000fc5f7688
x24: 00000000fedbb200 x25: 0000000000000003
x26: 00000000fc5f7688 x27: 00000000fedbb200
x28: 00000000fc84db70 x29: 00000000fc5f7440

Code: 44000000 00004000 08010048 40008000 (00100400) 
Resetting CPU ...

resetting ...
[0000.157] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de)
[0000.162] Processing in cold boot mode Bootloader 2
[0000.167] A02 Bootrom Patch rev = 1023
[0000.171] Power-up reason: software reset
[0000.174] No Battery Present
[0000.177] pmic max77620 reset reason
[0000.180] pmic max77620 NVERC : 0x0
[0000.184] RamCode = 0
[0000.186] Platform has DDR4 type RAM
[0000.189] max77620 disabling SD1 Remote Sense
[0000.193] Setting DDR voltage to 1125mv
[0000.197] Serial Number of Pmic Max77663: 0x802a4
[0000.205] Entering ramdump check
[0000.208] Get RamDumpCarveOut = 0x0
[0000.211] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0000.216] Last reboot was clean, booting normally!
[0000.221] Sdram initialization is successful 
[0000.225] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.231] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.237] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.243] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.249] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.255] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.260] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.266] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.282] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.288] Platform-DebugCarveout: 0
[0000.292] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.297] Non secure mode, and RB not enabled.
[0000.302] BoardID = 3448, SKU = 0x0
[0000.305] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.309] Nano-SD: checking PT table on QSPI ...
[0000.313] Read PT from (2:0)
[0000.329] Using BFS PT to query partitions 
[0000.334] Loading Tboot-CPU binary
[0000.363] Verifying TBC in OdmNonSecureSBK mode
[0000.373] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.380] Bootloader downloaded successfully.
[0000.384] Downloaded Tboot-CPU binary to 0xa0000258
[0000.389] MAX77620_GPIO5 configured
[0000.392] CPU power rail is up
[0000.395] CPU clock enabled
[0000.399] Performing RAM repair
[0000.402] Updating A64 Warmreset Address to 0xa00002e9
[0000.407] BoardID = 3448, SKU = 0x0
[0000.410] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.414] Nano-SD: checking PT table on QSPI ...
[0000.418] Loading NvTbootBootloaderDTB
[0000.484] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0000.558] Bootloader DTB Load Address: 0x83000000
[0000.562] BoardID = 3448, SKU = 0x0
[0000.566] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.569] Nano-SD: checking PT table on QSPI ...
[0000.574] Loading NvTbootKernelDTB
[0000.640] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0000.713] Kernel DTB Load Address: 0x83100000
[0000.717] BoardID = 3448, SKU = 0x0
[0000.720] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.724] Nano-SD: checking PT table on QSPI ...
[0000.730] Loading cboot binary
[0000.846] Verifying EBT in OdmNonSecureSBK mode
[0000.888] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0000.895] Bootloader downloaded successfully.
[0000.899] BoardID = 3448, SKU = 0x0
[0000.902] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.906] Nano-SD: checking PT table on QSPI ...
[0000.911] PT: Partition NCT NOT found ! 
[0000.915] Warning: Find Partition via PT Failed
[0000.919] Next binary entry address: 0x92c00258 
[0000.923] BoardId: 3448
[0000.928] Overriding pmu board id with proc board id
[0000.933] Display board id is not available 
[0000.937] BoardID = 3448, SKU = 0x0
[0000.940] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0000.944] Nano-SD: checking PT table on QSPI ...
[0001.049] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0001.106] /bpmp deleted
[0001.108] SC7EntryFw header found loaded at 0xff700000
[0001.303] OVR2 PMIC
[0001.305] Bpmp FW successfully loaded
[0001.309] BoardID = 3448, SKU = 0x0
[0001.312] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0001.316] Nano-SD: checking PT table on QSPI ...
[0001.321] WB0 init successfully at 0xff780000
[0001.325] Set NvDecSticky Bits
[0001.329] GSC2 address ff53fffc value c0edbbcc
[0001.335] GSC MC Settings done
[0001.338] BoardID = 3448, SKU = 0x0
[0001.341] QSPI-ONLY: SkipQspiOnlyFlag = 0
[0001.345] Nano-SD: checking PT table on QSPI ...
[0001.351] TOS Image length 53680
[0001.354]  Monitor size 53680
[0001.356]  OS size 0
[0001.372] Secure Os AES-CMAC Verification Success!
[0001.376] TOS image cipher info: plaintext
[0001.380] Loading and Validation of Secure OS Successful
[0001.396] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.401] NvTbootPackSdramParams: start. 
[0001.406] NvTbootPackSdramParams: done. 
[0001.409] Tegraboot started after 84882 us
[0001.413] Basic modules init took 886916 us
[0001.417] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB
[0001.423] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0001.428] Next stage binary read took 102860 us
[0001.433] Carveout took -126357 us
[0001.436] CPU initialization took 495394 us
[0001.440] Total time taken by TegraBoot 1358813 us

[0001.445] Starting CPU & Halting co-processor 

64NOTICE:  BL31: v1.3(release):5b49e7f80
NOTICE:  BL31: Built : 08:37:40, Feb 19 2021
ERROR:   Error initializing runtime service trusty_fast
[0001.567] RamCode = 0
[0001.572] LPDDR4 Training: Read DT: Number of tables = 2
[0001.577] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0001.589] EMC Training Successful
[0001.592] 408000 not found in DVFS table
[0001.599] RamCode = 0
[0001.602] DT Write: emc-table@204000 succeeded
[0001.608] DT Write: emc-table@1600000 succeeded
[0001.612] LPDDR4 Training: Write DT: Number of tables = 2
[0001.660] 
[0001.661] Debug Init done
[0001.663] Marked DTB cacheable
[0001.666] Bootloader DTB loaded at 0x83000000
[0001.671] Marked DTB cacheable
[0001.674] Kernel DTB loaded at 0x83100000
[0001.678] DeviceTree Init done
[0001.691] Pinmux applied successfully
[0001.695] gicd_base: 0x50041000
[0001.699] gicc_base: 0x50042000
[0001.702] Interrupts Init done
[0001.706] Using base:0x60005090 & irq:208 for tick-timer
[0001.711] Using base:0x60005098 for delay-timer
[0001.716] platform_init_timer: DONE
[0001.719] Timer(tick) Init done
[0001.723] osc freq = 38400 khz
[0001.727] 
[0001.728] Welcome to L4T Cboot
[0001.731] 
[0001.732] Cboot Version: 00.00.2018.01-t210-39562017
[0001.737] calling constructors
[0001.740] initializing heap
[0001.742] initializing threads
[0001.745] initializing timers
[0001.748] creating bootstrap completion thread
[0001.753] top of bootstrap2()
[0001.755] CPU: ARM Cortex A57
[0001.758] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0001.763] initializing platform
[0001.771] Manufacturer: MF = 0xc2, ID MSB = 0x25
[0001.775] ID LSB = 0x36, ID-CFI len = 194 bytes
[0001.780] Macronix QSPI chip present
[0001.783] SPI device register
[0001.786] init boot device
[0001.789] allocating memory for boot device(SPI)
[0001.793] registering boot device
[0001.802] QSPI bdev is already initialized
[0001.805] Enable APE clock
[0001.808] Un-powergate APE partition
[0001.812] of_register: registering tegra_udc to of_hal
[0001.817] of_register: registering inv20628-driver to of_hal
[0001.822] of_register: registering ads1015-driver to of_hal
[0001.828] of_register: registering lp8557-bl-driver to of_hal
[0001.834] of_register: registering bq2419x_charger to of_hal
[0001.839] of_register: registering bq27441_fuel_gauge to of_hal
[0001.851] gpio framework initialized
[0001.854] of_register: registering tca9539_gpio to of_hal
[0001.860] of_register: registering tca9539_gpio to of_hal
[0001.865] of_register: registering i2c_bus_driver to of_hal
[0001.871] of_register: registering i2c_bus_driver to of_hal
[0001.876] of_register: registering i2c_bus_driver to of_hal
[0001.882] pmic framework initialized
[0001.885] of_register: registering max77620_pmic to of_hal
[0001.891] regulator framework initialized
[0001.895] of_register: registering tps65132_bl_driver to of_hal
[0001.900] initializing target
[0001.906] gpio_driver_register: register 'tegra_gpio_driver' driver
[0001.914] board ID = D78, board SKU = 0
[0001.918] Skipping Z3!
[0001.923] fixed regulator driver initialized
[0001.941] initializing OF layer
[0001.944] NCK carveout not present
[0001.947] Skipping dts_overrides
[0001.951] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.968] I2C Bus Init done
[0001.971] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.981] I2C Bus Init done
[0001.984] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.994] I2C Bus Init done
[0001.997] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.007] I2C Bus Init done
[0002.010] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.020] I2C Bus Init done
[0002.023] of_children_init: Ops found for compatible string maxim,max77620
[0002.033] max77620_init using irq 118
[0002.038] register 'maxim,max77620' pmic
[0002.042] gpio_driver_register: register 'max77620-gpio' driver
[0002.049] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.059] I2C Bus Init done
[0002.063] NCK carveout not present
[0002.073] Find /i2c@7000c000's alias i2c0
[0002.076] get eeprom at 1-a0, size 256, type 0
[0002.085] Find /i2c@7000c500's alias i2c2
[0002.089] get eeprom at 3-a0, size 256, type 0
[0002.094] get eeprom at 3-ae, size 256, type 0
[0002.098] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.103] I2C slave not started
[0002.106] I2C write failed
[0002.109] Writing offset failed
[0002.112] eeprom_init: EEPROM read failed
[0002.116] pm_ids_update: eeprom init failed
[0002.120] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.150] pm_ids_update: The pm board id is 3448-0000-400
[0002.157] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50
[0002.165] pm_ids_update: pm id update successful
[0002.170] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.200] pm_ids_update: The pm board id is 3449-0000-400
[0002.206] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57
[0002.214] pm_ids_update: pm id update successful
[0002.244] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.250] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0002.258] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.264] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0002.272] updating /chosen/nvidia,ethernet-mac node 00:04:4b:eb:f1:a1
[0002.279] Plugin Manager: Parse ODM data 0x000a4000
[0002.291] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 
[0002.306] Find /i2c@7000c000's alias i2c0
[0002.310] get eeprom at 1-a0, size 256, type 0
[0002.319] Find /i2c@7000c500's alias i2c2
[0002.323] get eeprom at 3-a0, size 256, type 0
[0002.327] get eeprom at 3-ae, size 256, type 0
[0002.331] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.337] I2C slave not started
[0002.340] I2C write failed
[0002.342] Writing offset failed
[0002.345] eeprom_init: EEPROM read failed
[0002.349] pm_ids_update: eeprom init failed
[0002.353] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.384] pm_ids_update: The pm board id is 3448-0000-400
[0002.390] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50
[0002.397] pm_ids_update: pm id update successful
[0002.401] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.431] pm_ids_update: The pm board id is 3449-0000-400
[0002.438] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57
[0002.445] pm_ids_update: pm id update successful
[0002.475] Add serial number:1423119020987 as DT property
[0002.483] Applying platform configs
[0002.489] platform-init is not present. Skipping
[0002.494] calling apps_init()
[0002.500] Couldn't find GPT header
[0002.504] Proceeding to Cold Boot
[0002.507] starting app android_boot_app
[0002.511] Device state: unlocked
[0002.514] display console init
[0002.523] could not find regulator
[0002.526] hdmi cable connected
[0002.541] edid read success
[0002.557] edid reDT entry for leds-pwm not found
a[0002.565] d success
[0002.567] width = 640, height = 480, frequency = 25174825
[0002.572] width = 1920, height = 1080, frequency = 148500000
[0002.578] width = 1920, height = 540, frequency = 74250000
[0002.583] width = 1920, height = 1080, frequency = 148351648
[0002.589] width = 1920, height = 1080, frequency = 148351648
[0002.594] width = 1280, height = 720, frequency = 74175824
[0002.600] width = 1280, height = 720, frequency = 74175824
[0002.605] width = 720, height = 480, frequency = 26973026
[0002.611] width = 720, height = 576, frequency = 26973026
[0002.616] width = 720, height = 480, frequency = 26973026
[0002.621] width = 720, height = 576, frequency = 26973026
[0002.627] Best mode Width = 1920, Height = 1080, freq = 148351648
[0002.634] tmds-config node not found
[0002.639] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts
[0002.653] setting 'vdd-1v8' regulator to 1800000 micro volts
[0002.661] could not find regulator
[0002.664] could not find regulator
[0002.668] could not find regulator
[0002.696] using default cmu settings
[0002.699] dc_hdmi_enable, starting HDMI initialisation
[0002.706] dc_hdmi_enable, HDMI initialisation complete
[0002.711] list and configure display window
[0002.719] display console init completed
[0002.731] subnode volume_up is not found !
[0002.735] subnode back is not found !
[0002.738] subnode volume_down is not found !
[0002.742] subnode menu is not found !
[0002.746] Gpio keyboard init success
[0002.827] found decompressor handler: lz4-legacy
[0002.841] decompressing blob (type 1)...
[0002.911] load_bmp_blob: panelresolution=1080 type=3
[0002.986] decompressor handler not found
[0002.989] load_firmware_blob: Firmware blob loaded, entries=2
[0002.995] XUSB blob version 0 size 124416 @ 0x934ae28c
[0003.001] -------> se_aes_verify_sbk_clear: 747
[0003.006] se_aes_verify_sbk_clear: Error
[0003.009] SE operation failed
[0003.012] bl_battery_charging: connected to external power supply
[0003.025] device_query_partition_size: failed to open partition spiflash0:MSC !
[0003.032] MSC Partition not found
[0003.038] device_query_partition_size: failed to open partition spiflash0:USP !
[0003.045] USP partition read failed!
[0003.049] blob_init: blob-partition USP header read failed
[0003.054] android_boot Unable to update recovery partition
[0003.060] kfs_getpartname: name = LNX
[0003.063] Loading kernel from LNX
[0003.073] Found 19 BFS partitions in "spiflash0"
[0003.392] load kernel from storage
[0003.397] decompressor handler not found
[0003.662] Successfully loaded kernel and ramdisk images
[0003.667] board ID = D78, board SKU = 0
[0003.672] sdmmc node status = okay
[0003.675] sdcard instance = 0
[0003.678] sdcard gpio handle 0x5b
[0003.681] sdcard gpio pin 0xc9
[0003.684] sdcard gpio flags 0x0
[0003.687] vmmc-supply 0x9e
[0003.690] cd_gpio_pin = 201
[0003.692] pin_state = 1
[0003.695] No sdcard
[0003.697] SD-card NOT present ...
[0003.700] load_and_boot_kernel: SD card not detected!
[0003.706] load_bmp_blob: panelresolution=1080 type=3
[0004.202] display bmp image done