[0000.242] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de)
[0000.248] Processing in cold boot mode Bootloader 2
[0000.253] A02 Bootrom Patch rev = 1023
[0000.256] Power-up reason: pmc por
[0000.259] No Battery Present
[0000.262] pmic max77620 reset reason
[0000.265] pmic max77620 NVERC : 0x40
[0000.269] RamCode = 0
[0000.271] Platform has DDR4 type RAM
[0000.274] max77620 disabling SD1 Remote Sense
[0000.278] Setting DDR voltage to 1125mv
[0000.282] Serial Number of Pmic Max77663: 0x242aed
[0000.290] Entering ramdump check
[0000.293] Get RamDumpCarveOut = 0x0
[0000.296] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0000.302] Last reboot was clean, booting normally!
[0000.306] Sdram initialization is successful 
[0000.310] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.316] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.322] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.328] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.334] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.340] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.346] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.351] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.368] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.374] Platform-DebugCarveout: 0
[0000.377] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.383] Non secure mode, and RB not enabled.
[0000.399] Csd NumOfBlocks=0
[0000.597] *** Booting BFS0.
[0000.599] Read PT from (0:3)
[0000.605] Using BFS PT to query partitions 
[0000.609] PT: Partition LNX NOT found ! 
[0001.213] *** Booting KFS0.
[0001.216] BoardID = 3448, SKU = 0x2
[0001.219] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.225] Read GPT from (0:3)
[0001.233] Using GPT Primary to query partitions
[0001.238] Loading Tboot-CPU binary
[0001.245] Verifying TBC in OdmNonSecureSBK mode
[0001.255] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0001.262] Bootloader downloaded successfully.
[0001.266] Downloaded Tboot-CPU binary to 0xa0000258
[0001.271] MAX77620_GPIO5 configured
[0001.274] CPU power rail is up
[0001.277] CPU clock enabled
[0001.281] Performing RAM repair
[0001.284] Updating A64 Warmreset Address to 0xa00002e9
[0001.289] BoardID = 3448, SKU = 0x2
[0001.292] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.298] Loading NvTbootBootloaderDTB
[0001.315] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0001.389] Bootloader DTB Load Address: 0x83000000
[0001.393] BoardID = 3448, SKU = 0x2
[0001.397] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.402] Loading NvTbootKernelDTB
[0001.419] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0001.492] Kernel DTB Load Address: 0x83100000
[0001.496] BoardID = 3448, SKU = 0x2
[0001.500] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.507] Loading cboot binary
[0001.518] Verifying EBT in OdmNonSecureSBK mode
[0001.559] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0001.566] Bootloader downloaded successfully.
[0001.570] BoardID = 3448, SKU = 0x2
[0001.574] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.580] PT: Partition NCT NOT found ! 
[0001.584] Warning: Find Partition via PT Failed
[0001.588] Next binary entry address: 0x92c00258 
[0001.592] BoardId: 3448
[0001.597] Overriding pmu board id with proc board id
[0001.602] Display board id is not available 
[0001.606] BoardID = 3448, SKU = 0x2
[0001.609] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.623] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0001.679] /bpmp deleted
[0001.682] SC7EntryFw header found loaded at 0xff700000
[0001.877] OVR2 PMIC
[0001.879] Bpmp FW successfully loaded
[0001.883] BoardID = 3448, SKU = 0x2
[0001.886] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.893] WB0 init successfully at 0xff780000
[0001.897] Set NvDecSticky Bits
[0001.901] GSC2 address ff53fffc value c0edbbcc
[0001.907] GSC MC Settings done
[0001.910] BoardID = 3448, SKU = 0x2
[0001.913] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.920] TOS Image length 53680
[0001.923]  Monitor size 53680
[0001.926]  OS size 0
[0001.931] Secure Os AES-CMAC Verification Success!
[0001.936] TOS image cipher info: plaintext
[0001.940] Loading and Validation of Secure OS Successful
[0001.956] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.960] NvTbootPackSdramParams: start. 
[0001.965] NvTbootPackSdramParams: done. 
[0001.969] Tegraboot started after 172442 us
[0001.973] Basic modules init took 1482364 us
[0001.977] Sec Bootdevice Read Time = 565 ms, Read Size = 14649 KB
[0001.983] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0001.989] Next stage binary read took 7395 us
[0001.993] Carveout took -28703 us
[0001.996] CPU initialization took 383281 us
[0002.000] Total time taken by TegraBoot 1844337 us

[0002.005] Starting CPU & Halting co-processor 

64NOTICE:  BL31: v1.3(release):5b49e7f80
NOTICE:  BL31: Built : 08:37:40, Feb 19 2021
ERROR:   Error initializing runtime service trusty_fast
[0002.127] RamCode = 0
[0002.132] LPDDR4 Training: Read DT: Number of tables = 2
[0002.137] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0002.149] EMC Training Successful
[0002.152] 408000 not found in DVFS table
[0002.159] RamCode = 0
[0002.162] DT Write: emc-table@204000 succeeded
[0002.168] DT Write: emc-table@1600000 succeeded
[0002.172] LPDDR4 Training: Write DT: Number of tables = 2
[0002.233] 
[0002.234] Debug Init done
[0002.237] Marked DTB cacheable
[0002.240] Bootloader DTB loaded at 0x83000000
[0002.244] Marked DTB cacheable
[0002.247] Kernel DTB loaded at 0x83100000
[0002.251] DeviceTree Init done
[0002.264] Pinmux applied successfully
[0002.269] gicd_base: 0x50041000
[0002.272] gicc_base: 0x50042000
[0002.275] Interrupts Init done
[0002.279] Using base:0x60005090 & irq:208 for tick-timer
[0002.285] Using base:0x60005098 for delay-timer
[0002.289] platform_init_timer: DONE
[0002.292] Timer(tick) Init done
[0002.296] osc freq = 38400 khz
[0002.300] 
[0002.301] Welcome to L4T Cboot
[0002.304] 
[0002.305] Cboot Version: 00.00.2018.01-t210-39562017
[0002.310] calling constructors
[0002.313] initializing heap
[0002.316] initializing threads
[0002.319] initializing timers
[0002.322] creating bootstrap completion thread
[0002.326] top of bootstrap2()
[0002.329] CPU: ARM Cortex A57
[0002.332] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0002.337] initializing platform
[0002.390] Config for emmc ddr50 mode completed
[0002.395] sdmmc bdev is already initialized
[0002.399] Enable APE clock
[0002.401] Un-powergate APE partition
[0002.405] of_register: registering tegra_udc to of_hal
[0002.410] of_register: registering inv20628-driver to of_hal
[0002.416] of_register: registering ads1015-driver to of_hal
[0002.421] of_register: registering lp8557-bl-driver to of_hal
[0002.427] of_register: registering bq2419x_charger to of_hal
[0002.433] of_register: registering bq27441_fuel_gauge to of_hal
[0002.444] gpio framework initialized
[0002.448] of_register: registering tca9539_gpio to of_hal
[0002.453] of_register: registering tca9539_gpio to of_hal
[0002.458] of_register: registering i2c_bus_driver to of_hal
[0002.464] of_register: registering i2c_bus_driver to of_hal
[0002.470] of_register: registering i2c_bus_driver to of_hal
[0002.475] pmic framework initialized
[0002.479] of_register: registering max77620_pmic to of_hal
[0002.484] regulator framework initialized
[0002.488] of_register: registering tps65132_bl_driver to of_hal
[0002.494] initializing target
[0002.500] gpio_driver_register: register 'tegra_gpio_driver' driver
[0002.510] fixed regulator driver initialized
[0002.528] initializing OF layer
[0002.531] NCK carveout not present
[0002.535] Skipping dts_overrides
[0002.539] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.556] I2C Bus Init done
[0002.558] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.569] I2C Bus Init done
[0002.571] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.582] I2C Bus Init done
[0002.584] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.595] I2C Bus Init done
[0002.597] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.608] I2C Bus Init done
[0002.611] of_children_init: Ops found for compatible string maxim,max77620
[0002.621] max77620_init using irq 118
[0002.626] register 'maxim,max77620' pmic
[0002.630] gpio_driver_register: register 'max77620-gpio' driver
[0002.636] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.647] I2C Bus Init done
[0002.650] NCK carveout not present
[0002.660] Find /i2c@7000c000's alias i2c0
[0002.664] get eeprom at 1-a0, size 256, type 0
[0002.673] Find /i2c@7000c500's alias i2c2
[0002.677] get eeprom at 3-a0, size 256, type 0
[0002.681] get eeprom at 3-ae, size 256, type 0
[0002.686] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.691] I2C slave not started
[0002.694] I2C write failed
[0002.697] Writing offset failed
[0002.700] eeprom_init: EEPROM read failed
[0002.704] pm_ids_update: eeprom init failed
[0002.708] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.738] pm_ids_update: The pm board id is 3448-0002-400
[0002.745] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50
[0002.753] pm_ids_update: pm id update successful
[0002.757] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.788] eeprom_init: EEPROM incompatible version found
[0002.793] pm_ids_update: eeprom init failed
[0002.823] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.829] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0002.836] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.842] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0002.851] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e9:d1:dd
[0002.857] Plugin Manager: Parse ODM data 0x000a4000
[0002.869] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 
[0002.884] Find /i2c@7000c000's alias i2c0
[0002.888] get eeprom at 1-a0, size 256, type 0
[0002.897] Find /i2c@7000c500's alias i2c2
[0002.901] get eeprom at 3-a0, size 256, type 0
[0002.905] get eeprom at 3-ae, size 256, type 0
[0002.910] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.915] I2C slave not started
[0002.918] I2C write failed
[0002.921] Writing offset failed
[0002.924] eeprom_init: EEPROM read failed
[0002.928] pm_ids_update: eeprom init failed
[0002.932] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.962] pm_ids_update: The pm board id is 3448-0002-400
[0002.968] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50
[0002.975] pm_ids_update: pm id update successful
[0002.980] pm_ids_update: Updating 3,ae, size 256, type 0
[0003.010] eeprom_init: EEPROM incompatible version found
[0003.015] pm_ids_update: eeprom init failed
[0003.045] Add serial number:1423019114548 as DT property
[0003.052] Applying platform configs
[0003.059] platform-init is not present. Skipping
[0003.064] calling apps_init()
[0003.085] Found 17 GPT partitions in "sdmmc3_user"
[0003.090] Proceeding to Cold Boot
[0003.093] starting app android_boot_app
[0003.097] Device state: unlocked
[0003.100] display console init
[0003.108] could not find regulator
[0003.111] hdmi cable connected
[0003.127] edid read success
[0003.145] DT entry for leds-pwm not found
[0003.264] edid checksum could not be verified
[0003.268] This is not a CEA-extension block!
[0003.273] width = 1024, height = 600, frequency = 50000000
[0003.278] width = 720, height = 480, frequency = 27000000
[0003.283] Best mode Width = 640, Height = 480, freq = 25174825
[0003.291] tmds-config node not found
[0003.295] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts
[0003.310] setting 'vdd-1v8' regulator to 1800000 micro volts
[0003.317] could not find regulator
[0003.321] could not find regulator
[0003.324] could not find regulator
[0003.352] using default cmu settings
[0003.356] dc_hdmi_enable, starting HDMI initialisation
[0003.362] dc_hdmi_enable, HDMI initialisation complete
[0003.367] list and configure display window
[0003.372] display console init completed
[0003.380] subnode volume_up is not found !
[0003.384] subnode back is not found !
[0003.387] subnode volume_down is not found !
[0003.391] subnode menu is not found !
[0003.395] Gpio keyboard init success
[0003.444] found decompressor handler: lz4-legacy
[0003.458] decompressing blob (type 1)...
[0003.525] load_bmp_blob: panelresolution=480 type=0
[0003.576] decompressor handler not found
[0003.579] load_firmware_blob: Firmware blob loaded, entries=2
[0003.585] XUSB blob version 0 size 124416 @ 0x92df928c
[0003.591] -------> se_aes_verify_sbk_clear: 747
[0003.596] se_aes_verify_sbk_clear: Error
[0003.600] SE operation failed
[0003.602] bl_battery_charging: connected to external power supply
[0003.618] device_query_partition_size: failed to open partition sdmmc3_user:MSC !
[0003.625] MSC Partition not found
[0003.635] device_query_partition_size: failed to open partition sdmmc3_user:USP !
[0003.642] USP partition read failed!
[0003.646] blob_init: blob-partition USP header read failed
[0003.651] android_boot Unable to update recovery partition
[0003.657] kfs_getpartname: name = LNX
[0003.660] Loading kernel from LNX
[0003.754] load kernel from storage
[0003.764] decompressor handler not found
[0003.798] Successfully loaded kernel and ramdisk images
[0003.803] board ID = D78, board SKU = 2
[0003.808] load_bmp_blob: panelresolution=480 type=0
[0003.881] display bmp image done
[0003.884] NCK carveout not present
[0003.888] Skipping dts_overrides
[0003.891] NCK carveout not present
[0003.901] Find /i2c@7000c000's alias i2c0
[0003.904] get eeprom at 1-a0, size 256, type 0
[0003.913] Find /i2c@7000c500's alias i2c2
[0003.917] get eeprom at 3-a0, size 256, type 0
[0003.922] get eeprom at 3-ae, size 256, type 0
[0003.926] pm_ids_update: Updating 1,a0, size 256, type 0
[0003.931] I2C slave not started
[0003.934] I2C write failed
[0003.937] Writing offset failed
[0003.940] eeprom_init: EEPROM read failed
[0003.944] pm_ids_update: eeprom init failed
[0003.948] pm_ids_update: Updating 3,a0, size 256, type 0
[0003.978] pm_ids_update: The pm board id is 3448-0002-400
[0003.985] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50
[0003.993] pm_ids_update: pm id update successful
[0003.998] pm_ids_update: Updating 3,ae, size 256, type 0
[0004.028] eeprom_init: EEPROM incompatible version found
[0004.033] pm_ids_update: eeprom init failed
[0004.063] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0004.069] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0004.077] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0004.083] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0004.091] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e9:d1:dd
[0004.097] Plugin Manager: Parse ODM data 0x000a4000
[0004.110] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 
[0004.118] Add serial number:1423019114548 as DT property
[0004.127] "bpmp" doesn't exist, creating 
[0004.133] Updated bpmp info to DTB
[0004.138] Updated initrd info to DTB
[0004.141] "proc-board" doesn't exist, creating 
[0004.147] Updated board info to DTB
[0004.151] "pmu-board" doesn't exist, creating 
[0004.157] Updated board info to DTB
[0004.160] "display-board" doesn't exist, creating 
[0004.166] Updated board info to DTB
[0004.169] "reset" doesn't exist, creating 
[0004.174] Updated reset info to DTB
[0004.177] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 gpt tegra_fbmem=0x140000@0x92cb4000 is_hdmi_initialised=1 
[0004.217] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 
[0004.222] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 
[0004.238] Updated bootarg info to DTB
[0004.242] Adding uuid 00000001644568021c00000014000600 to DT
[0004.248] Adding eks info 0 to DT
[0004.254] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7
[0004.260] Updated memory info to DTB
[0004.268] set vdd_core voltage to 1125 mv
[0004.272] setting 'vdd-core' regulator to 1125000 micro volts
[0004.278] Found secure-pmc; disable BPMP


U-Boot 2020.04-g6b630d64fd (Feb 19 2021 - 08:37:46 -0800)

SoC: tegra210
Model: NVIDIA Jetson Nano Developer Kit
Board: NVIDIA P3450-0000
DRAM:  4 GiB
MMC:   sdhci@700b0000: 1, sdhci@700b0600: 0
Loading Environment from SPI Flash... *** Warning - spi_flash_probe_bus_cs() failed, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0 
Card did not respond to voltage select!
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
879 bytes read in 25 ms (34.2 KiB/s)
1:      primary kernel
Retrieving file: /boot/initrd
7159841 bytes read in 176 ms (38.8 MiB/s)
Retrieving file: /boot/Image
34338824 bytes read in 778 ms (42.1 MiB/s)
append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 gpt tegra_fbmem=0x140000@0x92cb4000 is_hdmi_initialised=1  earlycon=uart8250,mmio32,0x70006000  root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 
## Flattened Device Tree blob at 83100000
   Booting using the fdt blob at 0x83100000
ERROR: reserving fdt memory region failed (addr=0 size=0)
ERROR: reserving fdt memory region failed (addr=0 size=0)
   Using Device Tree in place at 0000000083100000, end 000000008317e8db
copying carveout for /host1x@50000000/dc@54200000...
copying carveout for /host1x@50000000/dc@54240000...

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.201-tegra (kurain@office) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #2 SMP PREEMPT Wed May 12 17:51:52 CST 2021
[    0.000000] Boot CPU: AArch64 Processor [411fd071]
[    0.000000] OF: fdt:memory scan node memory@80000000, reg size 32,
[    0.000000] OF: fdt: - 80000000 ,  7ee00000
[    0.000000] OF: fdt: - 100000000 ,  7f200000
[    0.000000] Found tegra_fbmem: 00140000@92cb4000
[    0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '')
[    0.000000] bootconsole [uart8250] enabled
[    1.198391] tegradc tegradc.1: dpd enable lookup fail:-19
[    1.216829] tegradc tegradc.1: dp: aux write got error (0x10000100)
[    1.223128] tegradc tegradc.1: dp: Failed for I2C write addr:80, size:1, stat:0x10000100
[    1.243571] tegradc tegradc.1: dp: aux write got error (0x10000100)
[    1.249852] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100
[    1.263571] tegradc tegradc.1: dp: aux write got error (0x10000100)
[    1.269847] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100
[    1.283156] tegradc tegradc.1: dp: aux write got error (0x10000100)
[    1.289434] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100
[    1.302758] tegradc tegradc.1: dp: aux write got error (0x10000100)
[    1.309034] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100
[    1.316228] imx219 7-0010: imx219_board_setup: error during i2c read probe (-121)
[    1.316295] imx219 7-0010: board setup failed
[    1.329147] tegradc tegradc.1: dp: failed to exit panel power save mode (0xfffffff2)
[    1.340112] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121)
[    1.347658] imx219 8-0010: board setup failed
[    1.451968] tegradc tegradc.1: dp: aux write got error (0x10000100)
[    1.451972] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100
[    1.456970] tegradc tegradc.1: dp: aux write got error (0x10000100)
[    1.456974] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100
[    1.462074] tegradc tegradc.1: dp: aux write got error (0x10000100)
[    1.462077] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100
[    1.467048] tegradc tegradc.1: dp: aux write got error (0x10000100)
[    1.467052] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100
[    1.467055] tegradc tegradc.1: dp: failed to exit panel power save mode (0xfffffff2)
[    1.467059] hpd: edid read prepare failed
[    1.907007] usb 1-2: device not accepting address 2, error -71
[    2.447348] cgroup: cgroup2: unknown option "nsdelegate"
[    2.650996] usb 1-2: device not accepting address 3, error -71
[    3.727459] using random self ethernet address
[    3.743002] using random host ethernet address
[    4.043336] random: crng init done
[    4.047845] random: 7 urandom warning(s) missed due to ratelimiting
[    4.274330] using random self ethernet address
[    4.280091] using random host ethernet address
[    4.371174] usb 1-2: device descriptor read/64, error -71
[    4.663136] usb 1-2: device descriptor read/64, error -71
[    5.135128] usb 1-2: device descriptor read/64, error -71
[    5.439120] usb 1-2: device descriptor read/64, error -71
[    5.551035] usb usb1-port2: unable to enumerate USB device
[    5.931288] usb 1-2: Device not responding to setup address.
[    6.143208] usb 1-2: Device not responding to setup address.
[    6.178966] mcp251x spi0.0: MCP251x didn't enter in conf mode after reset
[    6.190978] mcp251x spi0.0: Probe failed, err=16
[    6.191057] mcp251x: probe of spi0.0 failed with error -16
[    6.354955] usb 1-2: device not accepting address 6, error -71
[    6.643315] usb 1-2: Device not responding to setup address.
[    6.855230] usb 1-2: Device not responding to setup address.
[    7.067024] usb 1-2: device not accepting address 7, error -71

Ubuntu 18.04.5 LTS auto-desktop ttyS0

auto-desktop login: [    8.683155] usb 1-2: device descriptor read/64, error -71
[    8.927232] usb 1-2: device descriptor read/64, error -71
[    9.399096] usb 1-2: device descriptor read/64, error -71
[    9.691094] usb 1-2: device descriptor read/64, error -71
[    9.803068] usb usb1-port2: unable to enumerate USB device
[   11.659242] usb 1-2: Device not responding to setup address.
[   11.871221] usb 1-2: Device not responding to setup address.
[   12.082980] usb 1-2: device not accepting address 10, error -71
[   12.267225] usb 1-2: Device not responding to setup address.
[   12.479227] usb 1-2: Device not responding to setup address.
[   12.690966] usb 1-2: device not accepting address 11, error -71
[   14.411081] usb 1-2: device descriptor read/64, error -71
[   14.703168] usb 1-2: device descriptor read/64, error -71
[   15.179092] usb 1-2: device descriptor read/64, error -71
[   15.471093] usb 1-2: device descriptor read/64, error -71
[   15.583089] usb usb1-port2: unable to enumerate USB device
[   15.791237] usb 1-2: Device not responding to setup address.
[   16.003281] usb 1-2: Device not responding to setup address.
[   16.215034] usb 1-2: device not accepting address 14, error -71
[   16.399333] usb 1-2: Device not responding to setup address.
[   16.611231] usb 1-2: Device not responding to setup address.
[   16.823068] usb 1-2: device not accepting address 15, error -71
[   18.548419] usb 1-2: device descriptor read/64, error -71
[   18.844194] usb 1-2: device descriptor read/64, error -71
[   19.316962] usb 1-2: device descriptor read/64, error -71
[   19.616714] usb 1-2: device descriptor read/64, error -71
[   19.727835] usb usb1-port2: unable to enumerate USB device
[   19.931355] usb 1-2: Device not responding to setup address.
[   20.143385] usb 1-2: Device not responding to setup address.
[   20.355020] usb 1-2: device not accepting address 18, error -71
[   20.539273] usb 1-2: Device not responding to setup address.
[   20.751323] usb 1-2: Device not responding to setup address.
[   20.963022] usb 1-2: device not accepting address 19, error -71
[   22.683210] usb 1-2: device descriptor read/64, error -71
[   22.919205] usb 1-2: device descriptor read/64, error -71
[   23.391226] usb 1-2: device descriptor read/64, error -71
[   23.683454] usb 1-2: device descriptor read/64, error -71
[   23.795069] usb usb1-port2: unable to enumerate USB device
[   23.991443] usb 1-2: Device not responding to setup address.
[   24.203265] usb 1-2: Device not responding to setup address.
[   24.415062] usb 1-2: device not accepting address 22, error -71
[   24.599392] usb 1-2: Device not responding to setup address.
[   24.811339] usb 1-2: Device not responding to setup address.
[   25.022970] usb 1-2: device not accepting address 23, error -71
[   26.687188] usb 1-2: device descriptor read/64, error -71
[   26.923262] usb 1-2: device descriptor read/64, error -71
[   27.395201] usb 1-2: device descriptor read/64, error -71
[   27.687251] usb 1-2: device descriptor read/64, error -71
[   27.799055] usb usb1-port2: unable to enumerate USB device
[   27.999303] usb 1-2: Device not responding to setup address.
[   28.211261] usb 1-2: Device not responding to setup address.
[   28.423164] usb 1-2: device not accepting address 26, error -71
[   28.611289] usb 1-2: Device not responding to setup address.
[   28.823289] usb 1-2: Device not responding to setup address.
[   29.034975] usb 1-2: device not accepting address 27, error -71



























































[0000.242] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de)
[0000.248] Processing in cold boot mode Bootloader 2
[0000.253] A02 Bootrom Patch rev = 1023
[0000.256] Power-up reason: pmc por
[0000.259] No Battery Present
[0000.262] pmic max77620 reset reason
[0000.265] pmic max77620 NVERC : 0x40
[0000.269] RamCode = 0
[0000.271] Platform has DDR4 type RAM
[0000.274] max77620 disabling SD1 Remote Sense
[0000.278] Setting DDR voltage to 1125mv
[0000.282] Serial Number of Pmic Max77663: 0x242aed
[0000.290] Entering ramdump check
[0000.293] Get RamDumpCarveOut = 0x0
[0000.296] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0000.302] Last reboot was clean, booting normally!
[0000.306] Sdram initialization is successful 
[0000.310] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.316] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.322] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.328] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.334] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.340] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.346] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.351] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.368] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.374] Platform-DebugCarveout: 0
[0000.377] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.383] Non secure mode, and RB not enabled.
[0000.399] Csd NumOfBlocks=0
[0000.597] *** Booting BFS0.
[0000.599] Read PT from (0:3)
[0000.605] Using BFS PT to query partitions 
[0000.609] PT: Partition LNX NOT found ! 
[0001.213] *** Booting KFS0.
[0001.216] BoardID = 3448, SKU = 0x2
[0001.219] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.225] Read GPT from (0:3)
[0001.233] Using GPT Primary to query partitions
[0001.238] Loading Tboot-CPU binary
[0001.245] Verifying TBC in OdmNonSecureSBK mode
[0001.255] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0001.262] Bootloader downloaded successfully.
[0001.266] Downloaded Tboot-CPU binary to 0xa0000258
[0001.271] MAX77620_GPIO5 configured
[0001.274] CPU power rail is up
[0001.277] CPU clock enabled
[0001.281] Performing RAM repair
[0001.284] Updating A64 Warmreset Address to 0xa00002e9
[0001.289] BoardID = 3448, SKU = 0x2
[0001.292] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.298] Loading NvTbootBootloaderDTB
[0001.315] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0001.389] Bootloader DTB Load Address: 0x83000000
[0001.393] BoardID = 3448, SKU = 0x2
[0001.397] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.402] Loading NvTbootKernelDTB
[0001.419] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0001.492] Kernel DTB Load Address: 0x83100000
[0001.496] BoardID = 3448, SKU = 0x2
[0001.500] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.507] Loading cboot binary
[0001.518] Verifying EBT in OdmNonSecureSBK mode
[0001.559] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0001.566] Bootloader downloaded successfully.
[0001.570] BoardID = 3448, SKU = 0x2
[0001.574] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.580] PT: Partition NCT NOT found ! 
[0001.584] Warning: Find Partition via PT Failed
[0001.588] Next binary entry address: 0x92c00258 
[0001.592] BoardId: 3448
[0001.597] Overriding pmu board id with proc board id
[0001.602] Display board id is not available 
[0001.606] BoardID = 3448, SKU = 0x2
[0001.609] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.623] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0001.679] /bpmp deleted
[0001.682] SC7EntryFw header found loaded at 0xff700000
[0001.877] OVR2 PMIC
[0001.879] Bpmp FW successfully loaded
[0001.883] BoardID = 3448, SKU = 0x2
[0001.886] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.893] WB0 init successfully at 0xff780000
[0001.897] Set NvDecSticky Bits
[0001.901] GSC2 address ff53fffc value c0edbbcc
[0001.907] GSC MC Settings done
[0001.910] BoardID = 3448, SKU = 0x2
[0001.913] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.920] TOS Image length 53680
[0001.923]  Monitor size 53680
[0001.926]  OS size 0
[0001.931] Secure Os AES-CMAC Verification Success!
[0001.936] TOS image cipher info: plaintext
[0001.940] Loading and Validation of Secure OS Successful
[0001.956] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.960] NvTbootPackSdramParams: start. 
[0001.965] NvTbootPackSdramParams: done. 
[0001.969] Tegraboot started after 172442 us
[0001.973] Basic modules init took 1482364 us
[0001.977] Sec Bootdevice Read Time = 565 ms, Read Size = 14649 KB
[0001.983] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0001.989] Next stage binary read took 7395 us
[0001.993] Carveout took -28703 us
[0001.996] CPU initialization took 383281 us
[0002.000] Total time taken by TegraBoot 1844337 us

[0002.005] Starting CPU & Halting co-processor 

64NOTICE:  BL31: v1.3(release):5b49e7f80
NOTICE:  BL31: Built : 08:37:40, Feb 19 2021
ERROR:   Error initializing runtime service trusty_fast
[0002.127] RamCode = 0
[0002.132] LPDDR4 Training: Read DT: Number of tables = 2
[0002.137] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0002.149] EMC Training Successful
[0002.152] 408000 not found in DVFS table
[0002.159] RamCode = 0
[0002.162] DT Write: emc-table@204000 succeeded
[0002.168] DT Write: emc-table@1600000 succeeded
[0002.172] LPDDR4 Training: Write DT: Number of tables = 2
[0002.233] 
[0002.234] Debug Init done
[0002.237] Marked DTB cacheable
[0002.240] Bootloader DTB loaded at 0x83000000
[0002.244] Marked DTB cacheable
[0002.247] Kernel DTB loaded at 0x83100000
[0002.251] DeviceTree Init done
[0002.264] Pinmux applied successfully
[0002.269] gicd_base: 0x50041000
[0002.272] gicc_base: 0x50042000
[0002.275] Interrupts Init done
[0002.279] Using base:0x60005090 & irq:208 for tick-timer
[0002.285] Using base:0x60005098 for delay-timer
[0002.289] platform_init_timer: DONE
[0002.292] Timer(tick) Init done
[0002.296] osc freq = 38400 khz
[0002.300] 
[0002.301] Welcome to L4T Cboot
[0002.304] 
[0002.305] Cboot Version: 00.00.2018.01-t210-39562017
[0002.310] calling constructors
[0002.313] initializing heap
[0002.316] initializing threads
[0002.319] initializing timers
[0002.322] creating bootstrap completion thread
[0002.326] top of bootstrap2()
[0002.329] CPU: ARM Cortex A57
[0002.332] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0002.337] initializing platform
[0002.390] Config for emmc ddr50 mode completed
[0002.395] sdmmc bdev is already initialized
[0002.399] Enable APE clock
[0002.401] Un-powergate APE partition
[0002.405] of_register: registering tegra_udc to of_hal
[0002.410] of_register: registering inv20628-driver to of_hal
[0002.416] of_register: registering ads1015-driver to of_hal
[0002.421] of_register: registering lp8557-bl-driver to of_hal
[0002.427] of_register: registering bq2419x_charger to of_hal
[0002.433] of_register: registering bq27441_fuel_gauge to of_hal
[0002.444] gpio framework initialized
[0002.448] of_register: registering tca9539_gpio to of_hal
[0002.453] of_register: registering tca9539_gpio to of_hal
[0002.458] of_register: registering i2c_bus_driver to of_hal
[0002.464] of_register: registering i2c_bus_driver to of_hal
[0002.470] of_register: registering i2c_bus_driver to of_hal
[0002.475] pmic framework initialized
[0002.479] of_register: registering max77620_pmic to of_hal
[0002.484] regulator framework initialized
[0002.488] of_register: registering tps65132_bl_driver to of_hal
[0002.494] initializing target
[0002.500] gpio_driver_register: register 'tegra_gpio_driver' driver
[0002.510] fixed regulator driver initialized
[0002.528] initializing OF layer
[0002.531] NCK carveout not present
[0002.535] Skipping dts_overrides
[0002.539] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.556] I2C Bus Init done
[0002.558] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.569] I2C Bus Init done
[0002.571] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.582] I2C Bus Init done
[0002.584] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.595] I2C Bus Init done
[0002.597] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.608] I2C Bus Init done
[0002.611] of_children_init: Ops found for compatible string maxim,max77620
[0002.621] max77620_init using irq 118
[0002.626] register 'maxim,max77620' pmic
[0002.630] gpio_driver_register: register 'max77620-gpio' driver
[0002.636] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.647] I2C Bus Init done
[0002.650] NCK carveout not present
[0002.660] Find /i2c@7000c000's alias i2c0
[0002.664] get eeprom at 1-a0, size 256, type 0
[0002.673] Find /i2c@7000c500's alias i2c2
[0002.677] get eeprom at 3-a0, size 256, type 0
[0002.681] get eeprom at 3-ae, size 256, type 0
[0002.686] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.691] I2C slave not started
[0002.694] I2C write failed
[0002.697] Writing offset failed
[0002.700] eeprom_init: EEPROM read failed
[0002.704] pm_ids_update: eeprom init failed
[0002.708] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.738] pm_ids_update: The pm board id is 3448-0002-400
[0002.745] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50
[0002.753] pm_ids_update: pm id update successful
[0002.757] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.788] eeprom_init: EEPROM incompatible version found
[0002.793] pm_ids_update: eeprom init failed
[0002.823] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.829] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0002.836] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.842] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0002.851] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e9:d1:dd
[0002.857] Plugin Manager: Parse ODM data 0x000a4000
[0002.869] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 
[0002.884] Find /i2c@7000c000's alias i2c0
[0002.888] get eeprom at 1-a0, size 256, type 0
[0002.897] Find /i2c@7000c500's alias i2c2
[0002.901] get eeprom at 3-a0, size 256, type 0
[0002.905] get eeprom at 3-ae, size 256, type 0
[0002.910] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.915] I2C slave not started
[0002.918] I2C write failed
[0002.921] Writing offset failed
[0002.924] eeprom_init: EEPROM read failed
[0002.928] pm_ids_update: eeprom init failed
[0002.932] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.962] pm_ids_update: The pm board id is 3448-0002-400
[0002.968] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50
[0002.975] pm_ids_update: pm id update successful
[0002.980] pm_ids_update: Updating 3,ae, size 256, type 0
[0003.010] eeprom_init: EEPROM incompatible version found
[0003.015] pm_ids_update: eeprom init failed
[0003.045] Add serial number:1423019114548 as DT property
[0003.052] Applying platform configs
[0003.059] platform-init is not present. Skipping
[0003.064] calling apps_init()
[0003.085] Found 17 GPT partitions in "sdmmc3_user"
[0003.090] Proceeding to Cold Boot
[0003.093] starting app android_boot_app
[0003.097] Device state: unlocked
[0003.100] display console init
[0003.108] could not find regulator
[0003.111] hdmi cable connected
[0003.127] edid read success
[0003.145] DT entry for leds-pwm not found
[0003.264] edid checksum could not be verified
[0003.268] This is not a CEA-extension block!
[0003.273] width = 1024, height = 600, frequency = 50000000
[0003.278] width = 720, height = 480, frequency = 27000000
[0003.283] Best mode Width = 640, Height = 480, freq = 25174825
[0003.291] tmds-config node not found
[0003.295] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts
[0003.310] setting 'vdd-1v8' regulator to 1800000 micro volts
[0003.317] could not find regulator
[0003.321] could not find regulator
[0003.324] could not find regulator
[0003.352] using default cmu settings
[0003.356] dc_hdmi_enable, starting HDMI initialisation
[0003.362] dc_hdmi_enable, HDMI initialisation complete
[0003.367] list and configure display window
[0003.372] display console init completed
[0003.380] subnode volume_up is not found !
[0003.384] subnode back is not found !
[0003.387] subnode volume_down is not found !
[0003.391] subnode menu is not found !
[0003.395] Gpio keyboard init success
[0003.444] found decompressor handler: lz4-legacy
[0003.458] decompressing blob (type 1)...
[0003.525] load_bmp_blob: panelresolution=480 type=0
[0003.576] decompressor handler not found
[0003.579] load_firmware_blob: Firmware blob loaded, entries=2
[0003.585] XUSB blob version 0 size 124416 @ 0x92df928c
[0003.591] -------> se_aes_verify_sbk_clear: 747
[0003.596] se_aes_verify_sbk_clear: Error
[0003.600] SE operation failed
[0003.602] bl_battery_charging: connected to external power supply
[0003.618] device_query_partition_size: failed to open partition sdmmc3_user:MSC !
[0003.625] MSC Partition not found
[0003.635] device_query_partition_size: failed to open partition sdmmc3_user:USP !
[0003.642] USP partition read failed!
[0003.646] blob_init: blob-partition USP header read failed
[0003.651] android_boot Unable to update recovery partition
[0003.657] kfs_getpartname: name = LNX
[0003.660] Loading kernel from LNX
[0003.754] load kernel from storage
[0003.764] decompressor handler not found
[0003.798] Successfully loaded kernel and ramdisk images
[0003.803] board ID = D78, board SKU = 2
[0003.808] load_bmp_blob: panelresolution=480 type=0
[0003.881] display bmp image done
[0003.884] NCK carveout not present
[0003.888] Skipping dts_overrides
[0003.891] NCK carveout not present
[0003.901] Find /i2c@7000c000's alias i2c0
[0003.904] get eeprom at 1-a0, size 256, type 0
[0003.913] Find /i2c@7000c500's alias i2c2
[0003.917] get eeprom at 3-a0, size 256, type 0
[0003.922] get eeprom at 3-ae, size 256, type 0
[0003.926] pm_ids_update: Updating 1,a0, size 256, type 0
[0003.931] I2C slave not started
[0003.934] I2C write failed
[0003.937] Writing offset failed
[0003.940] eeprom_init: EEPROM read failed
[0003.944] pm_ids_update: eeprom init failed
[0003.948] pm_ids_update: Updating 3,a0, size 256, type 0
[0003.978] pm_ids_update: The pm board id is 3448-0002-400
[0003.985] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50
[0003.993] pm_ids_update: pm id update successful
[0003.998] pm_ids_update: Updating 3,ae, size 256, type 0
[0004.028] eeprom_init: EEPROM incompatible version found
[0004.033] pm_ids_update: eeprom init failed
[0004.063] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0004.069] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0004.077] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0004.083] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0004.091] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e9:d1:dd
[0004.097] Plugin Manager: Parse ODM data 0x000a4000
[0004.110] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 
[0004.118] Add serial number:1423019114548 as DT property
[0004.127] "bpmp" doesn't exist, creating 
[0004.133] Updated bpmp info to DTB
[0004.138] Updated initrd info to DTB
[0004.141] "proc-board" doesn't exist, creating 
[0004.147] Updated board info to DTB
[0004.151] "pmu-board" doesn't exist, creating 
[0004.157] Updated board info to DTB
[0004.160] "display-board" doesn't exist, creating 
[0004.166] Updated board info to DTB
[0004.169] "reset" doesn't exist, creating 
[0004.174] Updated reset info to DTB
[0004.177] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 gpt tegra_fbmem=0x140000@0x92cb4000 is_hdmi_initialised=1 
[0004.217] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 
[0004.222] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 
[0004.238] Updated bootarg info to DTB
[0004.242] Adding uuid 00000001644568021c00000014000600 to DT
[0004.248] Adding eks info 0 to DT
[0004.254] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7
[0004.260] Updated memory info to DTB
[0004.268] set vdd_core voltage to 1125 mv
[0004.272] setting 'vdd-core' regulator to 1125000 micro volts
[0004.278] Found secure-pmc; disable BPMP


U-Boot 2020.04-g6b630d64fd (Feb 19 2021 - 08:37:46 -0800)

SoC: tegra210
Model: NVIDIA Jetson Nano Developer Kit
Board: NVIDIA P3450-0000
DRAM:  4 GiB
MMC:   sdhci@700b0000: 1, sdhci@700b0600: 0
Loading Environment from SPI Flash... *** Warning - spi_flash_probe_bus_cs() failed, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0 
Card did not respond to voltage select!
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
879 bytes read in 25 ms (34.2 KiB/s)
1:      primary kernel
Retrieving file: /boot/initrd
7159841 bytes read in 176 ms (38.8 MiB/s)
Retrieving file: /boot/Image
34338824 bytes read in 778 ms (42.1 MiB/s)
append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 gpt tegra_fbmem=0x140000@0x92cb4000 is_hdmi_initialised=1  earlycon=uart8250,mmio32,0x70006000  root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 
## Flattened Device Tree blob at 83100000
   Booting using the fdt blob at 0x83100000
ERROR: reserving fdt memory region failed (addr=0 size=0)
ERROR: reserving fdt memory region failed (addr=0 size=0)
   Using Device Tree in place at 0000000083100000, end 000000008317e8db
copying carveout for /host1x@50000000/dc@54200000...
copying carveout for /host1x@50000000/dc@54240000...

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.201-tegra (kurain@office) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #2 SMP PREEMPT Wed May 12 17:51:52 CST 2021
[    0.000000] Boot CPU: AArch64 Processor [411fd071]
[    0.000000] OF: fdt:memory scan node memory@80000000, reg size 32,
[    0.000000] OF: fdt: - 80000000 ,  7ee00000
[    0.000000] OF: fdt: - 100000000 ,  7f200000
[    0.000000] Found tegra_fbmem: 00140000@92cb4000
[    0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '')
[    0.000000] bootconsole [uart8250] enabled
[    1.198391] tegradc tegradc.1: dpd enable lookup fail:-19
[    1.216829] tegradc tegradc.1: dp: aux write got error (0x10000100)
[    1.223128] tegradc tegradc.1: dp: Failed for I2C write addr:80, size:1, stat:0x10000100
[    1.243571] tegradc tegradc.1: dp: aux write got error (0x10000100)
[    1.249852] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100
[    1.263571] tegradc tegradc.1: dp: aux write got error (0x10000100)
[    1.269847] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100
[    1.283156] tegradc tegradc.1: dp: aux write got error (0x10000100)
[    1.289434] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100
[    1.302758] tegradc tegradc.1: dp: aux write got error (0x10000100)
[    1.309034] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100
[    1.316228] imx219 7-0010: imx219_board_setup: error during i2c read probe (-121)
[    1.316295] imx219 7-0010: board setup failed
[    1.329147] tegradc tegradc.1: dp: failed to exit panel power save mode (0xfffffff2)
[    1.340112] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121)
[    1.347658] imx219 8-0010: board setup failed
[    1.451968] tegradc tegradc.1: dp: aux write got error (0x10000100)
[    1.451972] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100
[    1.456970] tegradc tegradc.1: dp: aux write got error (0x10000100)
[    1.456974] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100
[    1.462074] tegradc tegradc.1: dp: aux write got error (0x10000100)
[    1.462077] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100
[    1.467048] tegradc tegradc.1: dp: aux write got error (0x10000100)
[    1.467052] tegradc tegradc.1: dp: Failed to write DPCD data. CMD 0x600, Status 0x10000100
[    1.467055] tegradc tegradc.1: dp: failed to exit panel power save mode (0xfffffff2)
[    1.467059] hpd: edid read prepare failed
[    1.907007] usb 1-2: device not accepting address 2, error -71
[    2.447348] cgroup: cgroup2: unknown option "nsdelegate"
[    2.650996] usb 1-2: device not accepting address 3, error -71
[    3.727459] using random self ethernet address
[    3.743002] using random host ethernet address
[    4.043336] random: crng init done
[    4.047845] random: 7 urandom warning(s) missed due to ratelimiting
[    4.274330] using random self ethernet address
[    4.280091] using random host ethernet address
[    4.371174] usb 1-2: device descriptor read/64, error -71
[    4.663136] usb 1-2: device descriptor read/64, error -71
[    5.135128] usb 1-2: device descriptor read/64, error -71
[    5.439120] usb 1-2: device descriptor read/64, error -71
[    5.551035] usb usb1-port2: unable to enumerate USB device
[    5.931288] usb 1-2: Device not responding to setup address.
[    6.143208] usb 1-2: Device not responding to setup address.
[    6.178966] mcp251x spi0.0: MCP251x didn't enter in conf mode after reset
[    6.190978] mcp251x spi0.0: Probe failed, err=16
[    6.191057] mcp251x: probe of spi0.0 failed with error -16
[    6.354955] usb 1-2: device not accepting address 6, error -71
[    6.643315] usb 1-2: Device not responding to setup address.
[    6.855230] usb 1-2: Device not responding to setup address.
[    7.067024] usb 1-2: device not accepting address 7, error -71

Ubuntu 18.04.5 LTS auto-desktop ttyS0

auto-desktop login: [    8.683155] usb 1-2: device descriptor read/64, error -71
[    8.927232] usb 1-2: device descriptor read/64, error -71
[    9.399096] usb 1-2: device descriptor read/64, error -71
[    9.691094] usb 1-2: device descriptor read/64, error -71
[    9.803068] usb usb1-port2: unable to enumerate USB device
[   11.659242] usb 1-2: Device not responding to setup address.
[   11.871221] usb 1-2: Device not responding to setup address.
[   12.082980] usb 1-2: device not accepting address 10, error -71
[   12.267225] usb 1-2: Device not responding to setup address.
[   12.479227] usb 1-2: Device not responding to setup address.
[   12.690966] usb 1-2: device not accepting address 11, error -71
[   14.411081] usb 1-2: device descriptor read/64, error -71
[   14.703168] usb 1-2: device descriptor read/64, error -71
[   15.179092] usb 1-2: device descriptor read/64, error -71
[   15.471093] usb 1-2: device descriptor read/64, error -71
[   15.583089] usb usb1-port2: unable to enumerate USB device
[   15.791237] usb 1-2: Device not responding to setup address.
[   16.003281] usb 1-2: Device not responding to setup address.
[   16.215034] usb 1-2: device not accepting address 14, error -71
[   16.399333] usb 1-2: Device not responding to setup address.
[   16.611231] usb 1-2: Device not responding to setup address.
[   16.823068] usb 1-2: device not accepting address 15, error -71
[   18.548419] usb 1-2: device descriptor read/64, error -71
[   18.844194] usb 1-2: device descriptor read/64, error -71
[   19.316962] usb 1-2: device descriptor read/64, error -71
[   19.616714] usb 1-2: device descriptor read/64, error -71
[   19.727835] usb usb1-port2: unable to enumerate USB device
[   19.931355] usb 1-2: Device not responding to setup address.
[   20.143385] usb 1-2: Device not responding to setup address.
[   20.355020] usb 1-2: device not accepting address 18, error -71
[   20.539273] usb 1-2: Device not responding to setup address.
[   20.751323] usb 1-2: Device not responding to setup address.
[   20.963022] usb 1-2: device not accepting address 19, error -71
[   22.683210] usb 1-2: device descriptor read/64, error -71
[   22.919205] usb 1-2: device descriptor read/64, error -71
[   23.391226] usb 1-2: device descriptor read/64, error -71
[   23.683454] usb 1-2: device descriptor read/64, error -71
[   23.795069] usb usb1-port2: unable to enumerate USB device
[   23.991443] usb 1-2: Device not responding to setup address.
[   24.203265] usb 1-2: Device not responding to setup address.
[   24.415062] usb 1-2: device not accepting address 22, error -71
[   24.599392] usb 1-2: Device not responding to setup address.
[   24.811339] usb 1-2: Device not responding to setup address.
[   25.022970] usb 1-2: device not accepting address 23, error -71
[   26.687188] usb 1-2: device descriptor read/64, error -71
[   26.923262] usb 1-2: device descriptor read/64, error -71
[   27.395201] usb 1-2: device descriptor read/64, error -71
[   27.687251] usb 1-2: device descriptor read/64, error -71
[   27.799055] usb usb1-port2: unable to enumerate USB device
[   27.999303] usb 1-2: Device not responding to setup address.
[   28.211261] usb 1-2: Device not responding to setup address.
[   28.423164] usb 1-2: device not accepting address 26, error -71
[   28.611289] usb 1-2: Device not responding to setup address.
[   28.823289] usb 1-2: Device not responding to setup address.
[   29.034975] usb 1-2: device not accepting address 27, error -71