[BEGIN] 2022/5/25 20:29:02
vþÿ
[0054.254] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fuses.
[0054.263] I> MB1 (prd-version: 1.5.1.6-t194-41334769-1740dd39)
[0054.268] I> Boot-mode: Platform RCM
[0054.271] I> Chip revision : A02P
[0054.274] I> Bootrom patch version : 15 (correctly patched)
[0054.280] I> ATE fuse revision : 0x200
[0054.283] I> Ram repair fuse : 0x0
[0054.286] I> Ram Code : 0x2
[0054.289] I> rst_source : 0x0
[0054.292] I> rst_level : 0x0
[0054.295] I> USB configuration success
[0056.543] I> mb2 image downloaded
[0056.625] I> Recovery boot mode 0
[0056.628] I> Boot-device: QSPI
[0056.633] I> UPHY full init done
[0056.637] I> MB1 done

[0056.642] W> Profiler not initialized
[0056.646] I> Welcome to MB2(TBoot-BPMP) Applet (version: 00.00.2018.32-mobile-e677d209)
[0056.654] W> Profiler not initialized
[0056.657] I> DMA Heap @ [0x40020000 - 0x40065800]
[0056.662] I> Default Heap @ [0xd486400 - 0xd48a400]
[0056.667] W> Profiler not initialized
[0056.670] W> Profiler not initialized
[0056.674] E> DEVICE_PROD: Invalid value data = 0, size = 0.
[0056.679] W> device prod register failed
[0056.683] W> Profiler not initialized
[0056.763] I> sdmmc DDR50 mode
[0056.768] I> QSPI Flash Size = 32 MB
[0056.779] I> Qspi initialized successfully
[0056.830] E> Link startup dme_set failed
[0056.834] E> UFS initialization failed
[0056.837] I> UFS is not present
[0056.840] W> Profiler not initialized
[0056.846] W> Cannot find any partition table for 00000003
[0056.852] W> Cannot find any partition table for 00010003
[0056.858] W> Cannot find any partition table for 00030000
[0056.863] W> Profiler not initialized
[0056.866] W> Profiler not initialized
[0056.870] W> Profiler not initialized
[0056.873] I> Entering 3p server
[0056.877] I> USB configuration success
[0057.999] I> Populate chip info
[0058.091] I> Populate eeprom info
[0058.095] I> Populate eeprom info for module cvm
[0058.311] I> Rebooting : reboot-recovery


[00
[0027.878] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fuses.
[0027.886] I> MB1 (prd-version: 1.5.1.6-t194-41334769-1740dd39)
[0027.892] I> Boot-mode: RCM
[0027.894] I> Chip revision : A02P
[0027.897] I> Bootrom patch version : 15 (correctly patched)
[0027.902] I> ATE fuse revision : 0x200
[0027.906] I> Ram repair fuse : 0x0
[0027.909] I> Ram Code : 0x2
[0027.911] I> rst_source : 0xb
[0027.914] I> rst_level : 0x1
[0027.918] I> USB configuration success
[0030.053] I> bct_bootrom image downloaded
[0030.061] W> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT.
[0030.069] I> Temperature = 47500
[0030.072] W> Skipping boost for clk: BPMP_CPU_NIC
[0030.076] W> Skipping boost for clk: BPMP_APB
[0030.080] W> Skipping boost for clk: AXI_CBB
[0030.084] W> Skipping boost for clk: AON_CPU_NIC
[0030.088] W> Skipping boost for clk: CAN1
[0030.092] W> Skipping boost for clk: CAN2
[0030.096] I> Boot-device: QSPI
[0030.099] I> Boot-device: QSPI
[0030.102] I> Qspi flash params source = mb1bct
[0030.106] I> bct_mb1 image downloaded
[0030.116] E> NONE: Invalid value MemBct dram size: 0MB for slot: 2.
[0030.122] C> OEM authentication of MEM-BCT failed!!!
[0030.127] E> NV3P_SERVER: Failed to verify image bct_mem.

[END] 2022/5/25 20:31:12