picocom v3.1 port is : /dev/ttyUSB0 flowcontrol : none baudrate is : 115200 parity is : none databits are : 8 stopbits are : 1 escape is : C-a local echo is : no noinit is : no noreset is : no hangup is : no nolock is : no send_cmd is : sz -vv receive_cmd is : rz -vv -E imap is : omap is : emap is : crcrlf,delbs, logfile is : none initstring : none exit_after is : not set exit is : no Type [C-a] [C-h] to see available commands Terminal ready яв [0006.506] W> RATCHET: MB1 binary ratchet value 4 is larger than ratchet level 2 from HW fuses. [0006.514] I> MB1 (prd-version: 2.3.0.0-t194-41334769-0a17edc1) [0006.520] I> Boot-mode: Platform RCM [0006.523] I> Platform: Silicon [0006.526] I> Chip revision : A02P [0006.529] I> Bootrom patch version : 15 (correctly patched) [0006.534] I> ATE fuse revision : 0x200 [0006.537] I> Ram repair fuse : 0x0 [0006.540] I> Ram Code : 0x2 [0006.543] I> rst_source: 0x0, rst_level: 0x0 [0006.548] I> USB configuration success [0010.072] I> mb2 image downloaded [0010.484] I> Recovery boot mode 0 [0010.489] I> UPHY full init done [0010.496] I> MB1 done [0010.501] I> Welcome to MB2(TBoot-BPMP) Applet (version: default.t194-mobile-27d8d121) [0010.509] I> DMA Heap @ [0x40020000 - 0x40065800] [0010.513] I> Default Heap @ [0xd486400 - 0xd48a400] [0010.518] W> Profiler not initialized [0010.599] I> sdmmc DDR50 mode [0010.606] I> QSPI-0l initialized successfully [0010.613] E> CLK_RST: instance 6 not found in module 44. [0010.618] E> MPhy CAR configuration failed error = 1747992077 [0010.623] E> UFS initialization failed [0010.626] I> UFS is not present [0010.631] W> Cannot find any partition table for 00000003 [0010.637] > PARTITION_MANAGER: Failed to publish partition. [0010.642] W> Cannot find any partition table for 00010003 [0010.648] > PARTITION_MANAGER: Failed to publish partition. [0010.654] W> Cannot find any partition table for 00030000 [0010.660] > PARTITION_MANAGER: Failed to publish partition. [0010.665] W> Profiler not initialized [0010.669] I> Entering 3p server [0010.672] I> USB configuration success [0013.275] I> Populate chip info [0013.688] I> Populate eeprom info [0013.691] I> Populate eeprom info for module cvm [0013.696] > DEVICE_PROD: device prod is not initialized. [0014.696] I> Rebooting : reboot-recovery [0014.700] I> Reset to recovery mode яв [0086.432] W> RATCHET: MB1 binary ratchet value 4 is larger than ratchet level 2 from HW fuses. [0086.440] I> MB1 (prd-version: 2.3.0.0-t194-41334769-0a17edc1) [0086.446] I> Boot-mode: RCM [0086.448] I> Platform: Silicon [0086.451] I> Chip revision : A02P [0086.454] I> Bootrom patch version : 15 (correctly patched) [0086.459] I> ATE fuse revision : 0x200 [0086.463] I> Ram repair fuse : 0x0 [0086.466] I> Ram Code : 0x2 [0086.468] I> rst_source: 0xb, rst_level: 0x1 [0086.473] I> USB configuration success [0089.373] I> bct_bootrom image downloaded [0089.381] W> PROD_CONFIG: device prod data is empty in MB1 BCT. [0089.389] I> Temperature = 34500 [0089.392] W> Skipping boost for clk: BPMP_CPU_NIC [0089.396] W> Skipping boost for clk: BPMP_APB [0089.400] W> Skipping boost for clk: AXI_CBB [0089.404] W> Skipping boost for clk: AON_CPU_NIC [0089.408] W> Skipping boost for clk: CAN1 [0089.412] W> Skipping boost for clk: CAN2 [0089.416] I> Boot-device: QSPI (instance: 0) [0089.420] I> Qspi flash params source = mb1bct [0089.424] I> bct_mb1 image downloaded [0089.434] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000 [0089.442] W> Thermal config not found in BCT [0089.450] W> MEMIO rail config not found in BCT [0089.462] C> Task 0x4d failed (err: 0x8c8c011c) [0089.466] E> Top caller module: MB1_MSS, error module: MB1_MSS, reason: 0x1c, aux_info: 0x01 [0089.474] C> Error: 0x8c8c011c [0089.477] C> MB1(2.3.0.0-t194-41334769-0a17edc1) BIT boot status dump : 0000000000111111111001000000000001111011111100000011111111111111001110001111100000000000000000000000000000000000000000000000000010100000000001010000000000000101000000000010100000000000000000000000000000000000000000000000000000000000000000000000000000000000 [0089.506] I> Reset to recovery mode яв [0000.025] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fuses. [0000.033] I> MB1 (prd-version: 1.5.1.3-t194-41334769-d2a21c57) [0000.039] I> Boot-mode: Coldboot [0000.042] I> Chip revision : A02P [0000.045] I> Bootrom patch version : 15 (correctly patched) [0000.050] I> ATE fuse revision : 0x200 [0000.054] I> Ram repair fuse : 0x0 [0000.057] I> Ram Code : 0x0 [0000.059] I> rst_source : 0x0 [0000.062] I> rst_level : 0x0 [0000.065] I> Boot-device: QSPI [0000.068] I> Qspi flash params source = brbct [0000.072] I> Qspi using bpmp-dma [0000.075] I> Qspi clock source : pllp [0000.079] I> QSPI Flash Size = 32 MB [0000.082] I> Qspi initialized successfully [0000.086] W> No valid slot number is found in scratch register [0000.091] W> Return default slot: _a [0000.095] I> Active Boot chain : 0 [0000.098] I> Boot-device: QSPI [0000.101] I> Qspi flash params source = brbct [0000.106] W> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT. [0000.114] I> Temperature = 25000 [0000.117] W> Skipping boost for clk: BPMP_CPU_NIC [0000.122] W> Skipping boost for clk: BPMP_APB [0000.126] W> Skipping boost for clk: AXI_CBB [0000.129] W> Skipping boost for clk: AON_CPU_NIC [0000.134] W> Skipping boost for clk: CAN1 [0000.137] W> Skipping boost for clk: CAN2 [0000.142] I> Boot-device: QSPI [0000.145] I> Boot-device: QSPI [0000.147] I> Qspi flash params source = mb1bct [0000.151] I> Qspi using bpmp-dma [0000.154] I> Qspi clock source : pllc_out0 [0000.158] I> Qspi reinitialized [0000.161] I> Qspi flash params source = mb1bct [0000.167] I> ECC region[0]: Start:0x0, End:0x0 [0000.171] I> ECC region[1]: Start:0x0, End:0x0 [0000.175] I> ECC region[2]: Start:0x0, End:0x0 [0000.179] I> ECC region[3]: Start:0x0, End:0x0 [0000.183] I> ECC region[4]: Start:0x0, End:0x0 [0000.187] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000 [0000.193] I> Non-ECC region[1]: Start:0x0, End:0x0 [0000.197] I> Non-ECC region[2]: Start:0x0, End:0x0 [0000.202] I> Non-ECC region[3]: Start:0x0, End:0x0 [0000.206] I> Non-ECC region[4]: Start:0x0, End:0x0 [0000.212] E> FAILED: Thermal config [0000.219] E> FAILED: MEMIO rail config [0000.229] E> Task 50 failed (err: 0x7979061c) [0000.233] E> Top caller module: ALIASCHECKER, error module: ALIASCHECKER, reason: 0x1c, aux_info: 0x06 [0000.242] I> MB1(1.5.1.3-t194-41334769-d2a21c57) BIT boot status dump : 0000000000011111111110111111111111111111111100111110000000000000000000000000000000000000000000000000000000000000000000000000000011011000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 [0000.272] I> Reset to recovery mode Terminating... Thanks for using picocom