[0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-80a468da)
[0000.131] Processing in cold boot mode Bootloader 2
[0000.135] A02 Bootrom Patch rev = 1023
[0000.139] Power-up reason: pmc por
[0000.142] No Battery Present
[0000.145] pmic max77620 reset reason
[0000.148] pmic max77620 NVERC : 0x40
[0000.151] RamCode = 0
[0000.154] Platform has DDR4 type RAM
[0000.157] max77620 disabling SD1 Remote Sense
[0000.161] Setting DDR voltage to 1125mv
[0000.165] Serial Number of Pmic Max77663: 0x3219e8
[0000.173] Entering ramdump check
[0000.176] Get RamDumpCarveOut = 0x0
[0000.179] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0000.184] Last reboot was clean, booting normally!
[0000.189] Sdram initialization is successful
[0000.193] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.199] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.205] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.211] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.234] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.256] Platform-DebugCarveout: 0
[0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.265] Non secure mode, and RB not enabled.
[0000.270] Read GPT from (4:0)
[0000.565] Csd NumOfBlocks=125042688
[0000.570] Set High speed to 1
[0000.580] Using GPT Primary to query partitions
[0000.584] Loading Tboot-CPU binary
[0000.594] Verifying TBC in OdmNonSecureSBK mode
[0000.604] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.611] Bootloader downloaded successfully.
[0000.615] Downloaded Tboot-CPU binary to 0xa0000258
[0000.620] MAX77620_GPIO5 configured
[0000.623] CPU power rail is up
[0000.626] CPU clock enabled
[0000.630] Performing RAM repair
[0000.633] Updating A64 Warmreset Address to 0xa00002e9
[0000.638] Loading NvTbootBootloaderDTB
[0000.662] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0000.728] Bootloader DTB Load Address: 0x83000000
[0000.733] Loading NvTbootKernelDTB
[0000.757] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0000.822] Kernel DTB Load Address: 0x83100000
[0000.827] Loading cboot binary
[0000.856] Verifying EBT in OdmNonSecureSBK mode
[0000.898] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0000.905] Bootloader downloaded successfully.
[0000.909] Read PT from (2:0)
[0000.925] Using BFS PT to query partitions
[0000.929] PT: Partition NCT NOT found !
[0000.933] Warning: Find Partition via PT Failed
[0000.937] Next binary entry address: 0x92c00258
[0000.941] BoardId: 3448
[0000.946] Overriding pmu board id with proc board id
[0000.951] Display board id is not available
[0000.979] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0001.031] /bpmp deleted
[0001.033] SC7EntryFw header found loaded at 0xff700000
[0001.223] OVR2 PMIC
[0001.225] Bpmp FW successfully loaded
[0001.229] WB0 init successfully at 0xff780000
[0001.233] Set NvDecSticky Bits
[0001.237] GSC2 address ff53fffc value c0edbbcc
[0001.243] GSC MC Settings done
[0001.247] TOS Image length 53680
[0001.250]  Monitor size 53680
[0001.253]  OS size 0
[0001.260] Secure Os AES-CMAC Verification Success!
[0001.264] TOS image cipher info: plaintext
[0001.268] Loading and Validation of Secure OS Successful
[0001.284] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.289] NvTbootPackSdramParams: start.
[0001.294] NvTbootPackSdramParams: done.
[0001.298] Tegraboot started after 52335 us
[0001.301] Basic modules init took 926067 us
[0001.306] Sec Bootdevice Read Time = 12 ms, Read Size = 65 KB
[0001.311] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0001.317] Storage Device Read Time = 108 ms, Read Size = 2241 KB
[0001.322] Storage Device Write Time = 0 ms, Write Size = 0 KB
[0001.328] Next stage binary read took 24383 us
[0001.332] Carveout took -36067 us
[0001.335] CPU initialization took 362390 us
[0001.339] Total time taken by TegraBoot 1276773 us

[0001.344] Starting CPU & Halting co-processor

64NOTICE:  BL31: v1.3(release):41d46a9cf
NOTICE:  BL31: Built : 15:55:29, Aug  3 2020
ERROR:   Error initializing runtime service trusty_fast
[0001.466] RamCode = 0
[0001.471] LPDDR4 Training: Read DT: Number of tables = 2
[0001.476] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0001.489] EMC Training Successful
[0001.492] 408000 not found in DVFS table
[0001.498] RamCode = 0
[0001.501] DT Write: emc-table@204000 succeeded
[0001.507] DT Write: emc-table@1600000 succeeded
[0001.511] LPDDR4 Training: Write DT: Number of tables = 2
[0001.556]
[0001.557] Debug Init done
[0001.560] Marked DTB cacheable
[0001.563] Bootloader DTB loaded at 0x83000000
[0001.568] Marked DTB cacheable
[0001.571] Kernel DTB loaded at 0x83100000
[0001.574] DeviceTree Init done
[0001.587] Pinmux applied successfully
[0001.592] gicd_base: 0x50041000
[0001.595] gicc_base: 0x50042000
[0001.598] Interrupts Init done
[0001.602] Using base:0x60005090 & irq:208 for tick-timer
[0001.608] Using base:0x60005098 for delay-timer
[0001.612] platform_init_timer: DONE
[0001.615] Timer(tick) Init done
[0001.619] osc freq = 38400 khz
[0001.623]
[0001.624] Welcome to L4T Cboot
[0001.627]
[0001.629] Cboot Version: 00.00.2018.01-t210-3a7ad565
[0001.633] calling constructors
[0001.636] initializing heap
[0001.639] initializing threads
[0001.642] initializing timers
[0001.645] creating bootstrap completion thread
[0001.649] top of bootstrap2()
[0001.652] CPU: ARM Cortex A57
[0001.655] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0001.660] initializing platform
[0001.667] Manufacturer: MF = 0xc2, ID MSB = 0x25
[0001.672] ID LSB = 0x36, ID-CFI len = 194 bytes
[0001.676] Macronix QSPI chip present
[0001.680] SPI device register
[0001.683] init boot device
[0001.685] allocating memory for boot device(SPI)
[0001.690] registering boot device
[0001.699] sdmmc node status = okay
[0001.702] sdcard instance = 0
[0001.705] sdcard gpio handle 0x56
[0001.708] sdcard gpio pin 0xc9
[0001.711] sdcard gpio flags 0x0
[0001.714] vmmc-supply 0x99
[0001.717] Instance: 0
[0001.719] Allocating memory for context
[0001.723] enabling clock
[0001.725] sd card init
[0001.728] Check card present and stable
[0001.731] Send command 0
[0001.748] Send command 3
[0001.752] Set RCA for the card
[0001.755] Query card specific data by command 9
[0001.762] Parse CSD data
[0001.764] Send command 7
[0001.774] Calling sd device register
[0001.778] Init sdcard
[0001.780] Allocating memory for boot device
[0001.784] Registering user device
[0001.797] Enable APE clock
[0001.800] Un-powergate APE partition
[0001.803] of_register: registering tegra_udc to of_hal
[0001.808] of_register: registering inv20628-driver to of_hal
[0001.814] of_register: registering ads1015-driver to of_hal
[0001.820] of_register: registering lp8557-bl-driver to of_hal
[0001.825] of_register: registering bq2419x_charger to of_hal
[0001.831] of_register: registering bq27441_fuel_gauge to of_hal
[0001.843] gpio framework initialized
[0001.846] of_register: registering tca9539_gpio to of_hal
[0001.851] of_register: registering tca9539_gpio to of_hal
[0001.857] of_register: registering i2c_bus_driver to of_hal
[0001.862] of_register: registering i2c_bus_driver to of_hal
[0001.868] of_register: registering i2c_bus_driver to of_hal
[0001.873] pmic framework initialized
[0001.877] of_register: registering max77620_pmic to of_hal
[0001.882] regulator framework initialized
[0001.886] of_register: registering tps65132_bl_driver to of_hal
[0001.892] initializing target
[0001.898] gpio_driver_register: register 'tegra_gpio_driver' driver
[0001.906] board ID = D78, board SKU = 0
[0001.910] Skipping Z3!
[0001.915] fixed regulator driver initialized
[0001.932] initializing OF layer
[0001.935] NCK carveout not present
[0001.938] Skipping dts_overrides
[0001.943] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.959] I2C Bus Init done
[0001.962] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.972] I2C Bus Init done
[0001.975] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.985] I2C Bus Init done
[0001.988] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.998] I2C Bus Init done
[0002.001] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.011] I2C Bus Init done
[0002.014] of_children_init: Ops found for compatible string maxim,max77620
[0002.024] max77620_init using irq 118
[0002.029] register 'maxim,max77620' pmic
[0002.033] gpio_driver_register: register 'max77620-gpio' driver
[0002.040] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.050] I2C Bus Init done
[0002.054] NCK carveout not present
[0002.064] Find /i2c@7000c000's alias i2c0
[0002.068] get eeprom at 1-a0, size 256, type 0
[0002.077] Find /i2c@7000c500's alias i2c2
[0002.080] get eeprom at 3-a0, size 256, type 0
[0002.085] get eeprom at 3-ae, size 256, type 0
[0002.089] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.095] I2C slave not started
[0002.098] I2C write failed
[0002.100] Writing offset failed
[0002.103] eeprom_init: EEPROM read failed
[0002.107] pm_ids_update: eeprom init failed
[0002.111] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.141] pm_ids_update: The pm board id is 3448-0000-200
[0002.148] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0002.156] pm_ids_update: pm id update successful
[0002.160] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.191] pm_ids_update: The pm board id is 3449-0000-200
[0002.197] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0002.205] pm_ids_update: pm id update successful
[0002.236] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.241] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0002.250] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.255] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0002.264] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:8c:b1
[0002.271] Plugin Manager: Parse ODM data 0x00094000
[0002.281] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000
[0002.295] Find /i2c@7000c000's alias i2c0
[0002.299] get eeprom at 1-a0, size 256, type 0
[0002.308] Find /i2c@7000c500's alias i2c2
[0002.312] get eeprom at 3-a0, size 256, type 0
[0002.316] get eeprom at 3-ae, size 256, type 0
[0002.321] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.326] I2C slave not started
[0002.329] I2C write failed
[0002.332] Writing offset failed
[0002.335] eeprom_init: EEPROM read failed
[0002.339] pm_ids_update: eeprom init failed
[0002.343] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.373] pm_ids_update: The pm board id is 3448-0000-200
[0002.379] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0002.386] pm_ids_update: pm id update successful
[0002.391] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.421] pm_ids_update: The pm board id is 3449-0000-200
[0002.428] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0002.434] pm_ids_update: pm id update successful
[0002.465] Add serial number:1422519063333 as DT property
[0002.473] Applying platform configs
[0002.480] platform-init is not present. Skipping
[0002.484] calling apps_init()
[0002.509] Found 12 GPT partitions in "sd0"
[0002.513] Proceeding to Cold Boot
[0002.516] starting app android_boot_app
[0002.520] Device state: unlocked
[0002.523] display console init
[0002.532] could not find regulator
[0002.535] hdmi cable connected
[0002.551] edid read success
[0002.568] DT entry for leds-pwm not found
[0002.572] edid read success
[0002.575] width = 640, height = 480, frequency = 25174825
[0002.580] width = 640, height = 480, frequency = 25174825
[0002.586] width = 640, height = 480, frequency = 25174825
[0002.591] width = 1920, height = 1080, frequency = 148500000
[0002.597] width = 1920, height = 1080, frequency = 174500000
[0002.602] width = 1280, height = 720, frequency = 74250000
[0002.608] width = 640, height = 480, frequency = 25174825
[0002.613] width = 720, height = 480, frequency = 26973026
[0002.618] width = 720, height = 480, frequency = 26973026
[0002.624] width = 1280, height = 720, frequency = 74175824
[0002.629] width = 720, height = 576, frequency = 26973026
[0002.635] width = 720, height = 576, frequency = 26973026
[0002.640] width = 1280, height = 720, frequency = 74175824
[0002.645] width = 1920, height = 1080, frequency = 148351648
[0002.651] width = 1920, height = 1080, frequency = 148351648
[0002.657] Best mode Width = 1920, Height = 1080, freq = 148351648
[0002.665] tmds-config node not found
[0002.669] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts
[0002.683] setting 'vdd-1v8' regulator to 1800000 micro volts
[0002.691] could not find regulator
[0002.694] could not find regulator
[0002.698] could not find regulator
[0002.726] using default cmu settings
[0002.729] dc_hdmi_enable, starting HDMI initialisation
[0002.736] dc_hdmi_enable, HDMI initialisation complete
[0002.741] list and configure display window
[0002.749] display console init completed
[0002.761] subnode volume_up is not found !
[0002.765] subnode back is not found !
[0002.768] subnode volume_down is not found !
[0002.772] subnode menu is not found !
[0002.776] Gpio keyboard init success
[0002.820] found decompressor handler: lz4-legacy
[0002.834] decompressing blob (type 1)...
[0002.870] load_bmp_blob: panelresolution=1080 type=3
[0002.921] decompressor handler not found
[0002.924] load_firmware_blob: Firmware blob loaded, entries=2
[0002.930] -------> se_aes_verify_sbk_clear: 747
[0002.935] se_aes_verify_sbk_clear: Error
[0002.938] bl_battery_charging: connected to external power supply
[0002.946] xusb is supported
[0002.952] error while finding nvidia,portmap
[0003.456] xusb blob version 0 size 124416
[0003.460] firmware size 124416
[0003.465] Firmware timestamp: 0x5da88fc3, Version: 50.25 release
[0003.475] xhci0: 64 bytes context size, 32-bit DMA
[0003.515] usbus0: 5.0Gbps Super Speed USB v3.0
[0003.535] uhub0: <Nvidia XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
[0004.185] uhub0: 9 ports with 9 removable, self powered
[0005.185] failed to get HID devices
[0005.188] failed to init xhci or no usb device attached
[0005.199] device_query_partition_size: failed to open partition sd0:MSC !
[0005.206] MSC Partition not found
[0005.212] device_query_partition_size: failed to open partition sd0:USP !
[0005.219] USP partition read failed!
[0005.222] blob_init: blob-partition USP header read failed
[0005.228] android_boot Unable to update recovery partition
[0005.233] kfs_getpartname: name = LNX
[0005.237] Loading kernel from LNX
[0005.335] load kernel from storage
[0005.347] decompressor handler not found
[0005.404] Successfully loaded kernel and ramdisk images
[0005.411] load_bmp_blob: panelresolution=1080 type=3
[0005.905] display bmp image done
[0005.908] NCK carveout not present
[0005.912] Skipping dts_overrides
[0005.915] NCK carveout not present
[0005.925] Find /i2c@7000c000's alias i2c0
[0005.929] get eeprom at 1-a0, size 256, type 0
[0005.937] Find /i2c@7000c500's alias i2c2
[0005.941] get eeprom at 3-a0, size 256, type 0
[0005.946] get eeprom at 3-ae, size 256, type 0
[0005.950] pm_ids_update: Updating 1,a0, size 256, type 0
[0005.955] I2C slave not started
[0005.958] I2C write failed
[0005.961] Writing offset failed
[0005.964] eeprom_init: EEPROM read failed
[0005.968] pm_ids_update: eeprom init failed
[0005.972] pm_ids_update: Updating 3,a0, size 256, type 0
[0006.002] pm_ids_update: The pm board id is 3448-0000-200
[0006.009] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0006.017] pm_ids_update: pm id update successful
[0006.021] pm_ids_update: Updating 3,ae, size 256, type 0
[0006.051] pm_ids_update: The pm board id is 3449-0000-200
[0006.058] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0006.066] pm_ids_update: pm id update successful
[0006.096] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0006.102] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0006.110] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0006.116] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0006.125] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:8c:b1
[0006.131] Plugin Manager: Parse ODM data 0x00094000
[0006.141] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000
[0006.149] Add serial number:1422519063333 as DT property
[0006.158] "bpmp" doesn't exist, creating
[0006.164] Updated bpmp info to DTB
[0006.169] Updated initrd info to DTB
[0006.172] "proc-board" doesn't exist, creating
[0006.178] Updated board info to DTB
[0006.181] "pmu-board" doesn't exist, creating
[0006.187] Updated board info to DTB
[0006.190] "display-board" doesn't exist, creating
[0006.196] Updated board info to DTB
[0006.199] "reset" doesn't exist, creating
[0006.204] Updated reset info to DTB
[0006.207] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video
[0006.246] DTB cmdline: earlycon=uart8250,mmio32,0x70006000
[0006.251] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
[0006.264] Updated bootarg info to DTB
[0006.268] Adding uuid 00000001644495811c00000003ff8400 to DT
[0006.274] Adding eks info 0 to DT
[0006.280] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7
[0006.285] Updated memory info to DTB
[0006.291] Updated system-lp0-disable info to DTB
[0006.300] set vdd_core voltage to 1075 mv
[0006.303] setting 'vdd-core' regulator to 1075000 micro volts
[0006.325] Found secure-pmc; disable BPMP


U-Boot 2016.07-ge6da093be3 (Aug 03 2020 - 15:55:24 -0700)

TEGRA210
Model: NVIDIA P3450-Porg
Board: NVIDIA P3450-PORG
DRAM:  4 GiB
MMC:   Tegra SD/MMC: 0, Tegra SD/MMC: 1
SF: Detected MX25U3235F with page size 256 Bytes, erase size 4 KiB, total 4 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
1376 bytes read in 125 ms (10.7 KiB/s)
1:      primary kernel
Retrieving file: /boot/initrd
5562384 bytes read in 295 ms (18 MiB/s)
Retrieving file: /boot/Image
34330632 bytes read in 1546 ms (21.2 MiB/s)
append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_t
## Flattened Device Tree blob at 83100000
   Booting using the fdt blob at 0x83100000
   reserving fdt memory region: addr=80000000 size=20000
   Using Device Tree in place at 0000000083100000, end 00000000831777a1

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.140-tegra (buildbrain@mobile-u64-3456) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f9197770
[    0.000000] Boot CPU: AArch64 Processor [411fd071]
[    0.000000] OF: fdt:memory scan node memory@80000000, reg size 48,
[    0.000000] OF: fdt: - 80000000 ,  7ee00000
[    0.000000] OF: fdt: - 100000000 ,  7f200000
[    0.000000] Found tegra_fbmem: 00800000@92cb4000
[    0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '')
[    0.000000] bootconsole [uart8250] enabled
[0000.157] [L4T TegraBoot] (version 00.00.2018.01-l4t-80a468da)
[0000.163] Processing in cold boot mode Bootloader 2
[0000.167] A02 Bootrom Patch rev = 1023
[0000.171] Power-up reason: software reset
[0000.175] No Battery Present
[0000.177] pmic max77620 reset reason
[0000.181] pmic max77620 NVERC : 0x0
[0000.184] RamCode = 0
[0000.186] Platform has DDR4 type RAM
[0000.190] max77620 disabling SD1 Remote Sense
[0000.194] Setting DDR voltage to 1125mv
[0000.198] Serial Number of Pmic Max77663: 0x3219e8
[0000.206] Entering ramdump check
[0000.209] Get RamDumpCarveOut = 0x0
[0000.212] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0000.217] Last reboot was clean, booting normally!
[0000.221] Sdram initialization is successful
[0000.226] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.232] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.237] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.243] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.249] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.255] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.261] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.267] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.283] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.289] Platform-DebugCarveout: 0
[0000.292] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.298] Non secure mode, and RB not enabled.
[0000.302] Read GPT from (4:0)
[0000.592] Csd NumOfBlocks=125042688
[0000.597] Set High speed to 1
[0000.606] Using GPT Primary to query partitions
[0000.611] Loading Tboot-CPU binary
[0000.621] Verifying TBC in OdmNonSecureSBK mode
[0000.631] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.638] Bootloader downloaded successfully.
[0000.642] Downloaded Tboot-CPU binary to 0xa0000258
[0000.647] MAX77620_GPIO5 configured
[0000.650] CPU power rail is up
[0000.653] CPU clock enabled
[0000.657] Performing RAM repair
[0000.660] Updating A64 Warmreset Address to 0xa00002e9
[0000.665] Loading NvTbootBootloaderDTB
[0000.689] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0000.755] Bootloader DTB Load Address: 0x83000000
[0000.759] Loading NvTbootKernelDTB
[0000.784] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0000.849] Kernel DTB Load Address: 0x83100000
[0000.853] Loading cboot binary
[0000.883] Verifying EBT in OdmNonSecureSBK mode
[0000.925] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0000.932] Bootloader downloaded successfully.
[0000.936] Read PT from (2:0)
[0000.952] Using BFS PT to query partitions
[0000.956] PT: Partition NCT NOT found !
[0000.959] Warning: Find Partition via PT Failed
[0000.964] Next binary entry address: 0x92c00258
[0000.968] BoardId: 3448
[0000.973] Overriding pmu board id with proc board id
[0000.977] Display board id is not available
[0001.006] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0001.058] /bpmp deleted
[0001.060] SC7EntryFw header found loaded at 0xff700000
[0001.250] OVR2 PMIC
[0001.252] Bpmp FW successfully loaded
[0001.256] WB0 init successfully at 0xff780000
[0001.260] Set NvDecSticky Bits
[0001.264] GSC2 address ff53fffc value c0edbbcc
[0001.270] GSC MC Settings done
[0001.274] TOS Image length 53680
[0001.277]  Monitor size 53680
[0001.279]  OS size 0
[0001.287] Secure Os AES-CMAC Verification Success!
[0001.291] TOS image cipher info: plaintext
[0001.295] Loading and Validation of Secure OS Successful
[0001.311] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.316] NvTbootPackSdramParams: start.
[0001.321] NvTbootPackSdramParams: done.
[0001.324] Tegraboot started after 85372 us
[0001.328] Basic modules init took 920502 us
[0001.332] Sec Bootdevice Read Time = 12 ms, Read Size = 65 KB
[0001.338] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0001.343] Storage Device Read Time = 108 ms, Read Size = 2241 KB
[0001.349] Storage Device Write Time = 0 ms, Write Size = 0 KB
[0001.355] Next stage binary read took 24383 us
[0001.359] Carveout took -36067 us
[0001.362] CPU initialization took 362403 us
[0001.366] Total time taken by TegraBoot 1271221 us

[0001.371] Starting CPU & Halting co-processor

64NOTICE:  BL31: v1.3(release):41d46a9cf
NOTICE:  BL31: Built : 15:55:29, Aug  3 2020
ERROR:   Error initializing runtime service trusty_fast
[0001.493] RamCode = 0
[0001.498] LPDDR4 Training: Read DT: Number of tables = 2
[0001.503] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0001.515] EMC Training Successful
[0001.518] 408000 not found in DVFS table
[0001.525] RamCode = 0
[0001.528] DT Write: emc-table@204000 succeeded
[0001.534] DT Write: emc-table@1600000 succeeded
[0001.538] LPDDR4 Training: Write DT: Number of tables = 2
[0001.584]
[0001.585] Debug Init done
[0001.587] Marked DTB cacheable
[0001.590] Bootloader DTB loaded at 0x83000000
[0001.595] Marked DTB cacheable
[0001.598] Kernel DTB loaded at 0x83100000
[0001.602] DeviceTree Init done
[0001.615] Pinmux applied successfully
[0001.619] gicd_base: 0x50041000
[0001.623] gicc_base: 0x50042000
[0001.626] Interrupts Init done
[0001.630] Using base:0x60005090 & irq:208 for tick-timer
[0001.635] Using base:0x60005098 for delay-timer
[0001.640] platform_init_timer: DONE
[0001.643] Timer(tick) Init done
[0001.647] osc freq = 38400 khz
[0001.651]
[0001.652] Welcome to L4T Cboot
[0001.655]
[0001.656] Cboot Version: 00.00.2018.01-t210-3a7ad565
[0001.661] calling constructors
[0001.664] initializing heap
[0001.667] initializing threads
[0001.670] initializing timers
[0001.672] creating bootstrap completion thread
[0001.677] top of bootstrap2()
[0001.680] CPU: ARM Cortex A57
[0001.683] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0001.687] initializing platform
[0001.695] Manufacturer: MF = 0xc2, ID MSB = 0x25
[0001.699] ID LSB = 0x36, ID-CFI len = 194 bytes
[0001.704] Macronix QSPI chip present
[0001.707] SPI device register
[0001.710] init boot device
[0001.713] allocating memory for boot device(SPI)
[0001.717] registering boot device
[0001.727] sdmmc node status = okay
[0001.730] sdcard instance = 0
[0001.733] sdcard gpio handle 0x56
[0001.736] sdcard gpio pin 0xc9
[0001.739] sdcard gpio flags 0x0
[0001.742] vmmc-supply 0x99
[0001.745] Instance: 0
[0001.747] Allocating memory for context
[0001.751] enabling clock
[0001.753] sd card init
[0001.755] Check card present and stable
[0001.759] Send command 0
[0001.775] Send command 3
[0001.780] Set RCA for the card
[0001.783] Query card specific data by command 9
[0001.789] Parse CSD data
[0001.791] Send command 7
[0001.802] Calling sd device register
[0001.805] Init sdcard
[0001.807] Allocating memory for boot device
[0001.812] Registering user device
[0001.825] Enable APE clock
[0001.827] Un-powergate APE partition
[0001.831] of_register: registering tegra_udc to of_hal
[0001.836] of_register: registering inv20628-driver to of_hal
[0001.842] of_register: registering ads1015-driver to of_hal
[0001.847] of_register: registering lp8557-bl-driver to of_hal
[0001.853] of_register: registering bq2419x_charger to of_hal
[0001.859] of_register: registering bq27441_fuel_gauge to of_hal
[0001.870] gpio framework initialized
[0001.874] of_register: registering tca9539_gpio to of_hal
[0001.879] of_register: registering tca9539_gpio to of_hal
[0001.884] of_register: registering i2c_bus_driver to of_hal
[0001.890] of_register: registering i2c_bus_driver to of_hal
[0001.895] of_register: registering i2c_bus_driver to of_hal
[0001.901] pmic framework initialized
[0001.904] of_register: registering max77620_pmic to of_hal
[0001.910] regulator framework initialized
[0001.914] of_register: registering tps65132_bl_driver to of_hal
[0001.920] initializing target
[0001.926] gpio_driver_register: register 'tegra_gpio_driver' driver
[0001.934] board ID = D78, board SKU = 0
[0001.937] Skipping Z3!
[0001.942] fixed regulator driver initialized
[0001.960] initializing OF layer
[0001.963] NCK carveout not present
[0001.966] Skipping dts_overrides
[0001.970] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.987] I2C Bus Init done
[0001.990] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.000] I2C Bus Init done
[0002.003] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.013] I2C Bus Init done
[0002.016] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.026] I2C Bus Init done
[0002.029] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.039] I2C Bus Init done
[0002.042] of_children_init: Ops found for compatible string maxim,max77620
[0002.052] max77620_init using irq 118
[0002.057] register 'maxim,max77620' pmic
[0002.061] gpio_driver_register: register 'max77620-gpio' driver
[0002.067] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.078] I2C Bus Init done
[0002.081] NCK carveout not present
[0002.091] Find /i2c@7000c000's alias i2c0
[0002.095] get eeprom at 1-a0, size 256, type 0
[0002.104] Find /i2c@7000c500's alias i2c2
[0002.108] get eeprom at 3-a0, size 256, type 0
[0002.112] get eeprom at 3-ae, size 256, type 0
[0002.117] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.122] I2C slave not started
[0002.125] I2C write failed
[0002.128] Writing offset failed
[0002.131] eeprom_init: EEPROM read failed
[0002.135] pm_ids_update: eeprom init failed
[0002.139] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.169] pm_ids_update: The pm board id is 3448-0000-200
[0002.176] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0002.183] pm_ids_update: pm id update successful
[0002.188] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.218] pm_ids_update: The pm board id is 3449-0000-200
[0002.224] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0002.232] pm_ids_update: pm id update successful
[0002.263] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.269] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0002.277] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.283] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0002.291] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:8c:b1
[0002.298] Plugin Manager: Parse ODM data 0x00094000
[0002.308] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000
[0002.323] Find /i2c@7000c000's alias i2c0
[0002.327] get eeprom at 1-a0, size 256, type 0
[0002.335] Find /i2c@7000c500's alias i2c2
[0002.339] get eeprom at 3-a0, size 256, type 0
[0002.344] get eeprom at 3-ae, size 256, type 0
[0002.348] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.353] I2C slave not started
[0002.356] I2C write failed
[0002.359] Writing offset failed
[0002.362] eeprom_init: EEPROM read failed
[0002.366] pm_ids_update: eeprom init failed
[0002.370] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.400] pm_ids_update: The pm board id is 3448-0000-200
[0002.407] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0002.414] pm_ids_update: pm id update successful
[0002.418] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.448] pm_ids_update: The pm board id is 3449-0000-200
[0002.455] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0002.462] pm_ids_update: pm id update successful
[0002.492] Add serial number:1422519063333 as DT property
[0002.500] Applying platform configs
[0002.507] platform-init is not present. Skipping
[0002.511] calling apps_init()
[0002.537] Found 12 GPT partitions in "sd0"
[0002.541] Proceeding to Cold Boot
[0002.544] starting app android_boot_app
[0002.548] Device state: unlocked
[0002.551] display console init
[0002.559] could not find regulator
[0002.563] hdmi cable connected
[0002.578] edid read success
[0002.596] DT entry for leds-pwm not found
[0002.600] edid read success
[0002.602] width = 640, height = 480, frequency = 25174825
[0002.608] width = 640, height = 480, frequency = 25174825
[0002.613] width = 640, height = 480, frequency = 25174825
[0002.618] width = 1920, height = 1080, frequency = 148500000
[0002.624] width = 1920, height = 1080, frequency = 174500000
[0002.630] width = 1280, height = 720, frequency = 74250000
[0002.635] width = 640, height = 480, frequency = 25174825
[0002.641] width = 720, height = 480, frequency = 26973026
[0002.646] width = 720, height = 480, frequency = 26973026
[0002.651] width = 1280, height = 720, frequency = 74175824
[0002.657] width = 720, height = 576, frequency = 26973026
[0002.662] width = 720, height = 576, frequency = 26973026
[0002.668] width = 1280, height = 720, frequency = 74175824
[0002.673] width = 1920, height = 1080, frequency = 148351648
[0002.679] width = 1920, height = 1080, frequency = 148351648
[0002.684] Best mode Width = 1920, Height = 1080, freq = 148351648
[0002.692] tmds-config node not found
[0002.696] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts
[0002.711] setting 'vdd-1v8' regulator to 1800000 micro volts
[0002.719] could not find regulator
[0002.722] could not find regulator
[0002.725] could not find regulator
[0002.753] using default cmu settings
[0002.757] dc_hdmi_enable, starting HDMI initialisation
[0002.763] dc_hdmi_enable, HDMI initialisation complete
[0002.768] list and configure display window
[0002.777] display console init completed
[0002.788] subnode volume_up is not found !
[0002.792] subnode back is not found !
[0002.796] subnode volume_down is not found !
[0002.800] subnode menu is not found !
[0002.803] Gpio keyboard init success
[0002.847] found decompressor handler: lz4-legacy
[0002.862] decompressing blob (type 1)...
[0002.897] load_bmp_blob: panelresolution=1080 type=3
[0002.948] decompressor handler not found
[0002.952] load_firmware_blob: Firmware blob loaded, entries=2
[0002.958] -------> se_aes_verify_sbk_clear: 747
[0002.962] se_aes_verify_sbk_clear: Error
[0002.966] bl_battery_charging: connected to external power supply
[0002.973] xusb is supported
[0002.979] error while finding nvidia,portmap
[0003.484] xusb blob version 0 size 124416
[0003.487] firmware size 124416
[0003.492] Firmware timestamp: 0x5da88fc3, Version: 50.25 release
[0003.502] xhci0: 64 bytes context size, 32-bit DMA
[0003.542] usbus0: 5.0Gbps Super Speed USB v3.0
[0003.563] uhub0: <Nvidia XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
[0004.212] uhub0: 9 ports with 9 removable, self powered
[0005.212] failed to get HID devices
[0005.216] failed to init xhci or no usb device attached
[0005.226] device_query_partition_size: failed to open partition sd0:MSC !
[0005.233] MSC Partition not found
[0005.239] device_query_partition_size: failed to open partition sd0:USP !
[0005.246] USP partition read failed!
[0005.250] blob_init: blob-partition USP header read failed
[0005.255] android_boot Unable to update recovery partition
[0005.261] kfs_getpartname: name = LNX
[0005.264] Loading kernel from LNX
[0005.363] load kernel from storage
[0005.374] decompressor handler not found
[0005.432] Successfully loaded kernel and ramdisk images
[0005.438] load_bmp_blob: panelresolution=1080 type=3
[0005.933] display bmp image done
[0005.936] NCK carveout not present
[0005.939] Skipping dts_overrides
[0005.942] NCK carveout not present
[0005.952] Find /i2c@7000c000's alias i2c0
[0005.956] get eeprom at 1-a0, size 256, type 0
[0005.965] Find /i2c@7000c500's alias i2c2
[0005.969] get eeprom at 3-a0, size 256, type 0
[0005.973] get eeprom at 3-ae, size 256, type 0
[0005.978] pm_ids_update: Updating 1,a0, size 256, type 0
[0005.983] I2C slave not started
[0005.986] I2C write failed
[0005.989] Writing offset failed
[0005.992] eeprom_init: EEPROM read failed
[0005.996] pm_ids_update: eeprom init failed
[0006.000] pm_ids_update: Updating 3,a0, size 256, type 0
[0006.030] pm_ids_update: The pm board id is 3448-0000-200
[0006.037] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0006.044] pm_ids_update: pm id update successful
[0006.049] pm_ids_update: Updating 3,ae, size 256, type 0
[0006.079] pm_ids_update: The pm board id is 3449-0000-200
[0006.086] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0006.093] pm_ids_update: pm id update successful
[0006.124] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0006.130] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0006.138] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0006.144] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0006.153] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:8c:b1
[0006.159] Plugin Manager: Parse ODM data 0x00094000
[0006.169] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000
[0006.177] Add serial number:1422519063333 as DT property
[0006.186] "bpmp" doesn't exist, creating
[0006.192] Updated bpmp info to DTB
[0006.197] Updated initrd info to DTB
[0006.200] "proc-board" doesn't exist, creating
[0006.206] Updated board info to DTB
[0006.209] "pmu-board" doesn't exist, creating
[0006.214] Updated board info to DTB
[0006.218] "display-board" doesn't exist, creating
[0006.223] Updated board info to DTB
[0006.227] "reset" doesn't exist, creating
[0006.231] Updated reset info to DTB
[0006.235] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video
[0006.274] DTB cmdline: earlycon=uart8250,mmio32,0x70006000
[0006.279] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
[0006.292] Updated bootarg info to DTB
[0006.296] Adding uuid 00000001644495811c00000003ff8400 to DT
[0006.302] Adding eks info 0 to DT
[0006.307] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7
[0006.313] Updated memory info to DTB
[0006.319] Updated system-lp0-disable info to DTB
[0006.327] set vdd_core voltage to 1075 mv
[0006.331] setting 'vdd-core' regulator to 1075000 micro volts
[0006.352] Found secure-pmc; disable BPMP


U-Boot 2016.07-ge6da093be3 (Aug 03 2020 - 15:55:24 -0700)

TEGRA210
Model: NVIDIA P3450-Porg
Board: NVIDIA P3450-PORG
DRAM:  4 GiB
MMC:   Tegra SD/MMC: 0, Tegra SD/MMC: 1
SF: Detected MX25U3235F with page size 256 Bytes, erase size 4 KiB, total 4 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
1376 bytes read in 125 ms (10.7 KiB/s)
1:      primary kernel
Retrieving file: /boot/initrd
5562384 bytes read in 296 ms (17.9 MiB/s)
Retrieving file: /boot/Image
34330632 bytes read in 1545 ms (21.2 MiB/s)
append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_t
## Flattened Device Tree blob at 83100000
   Booting using the fdt blob at 0x83100000
   reserving fdt memory region: addr=80000000 size=20000
   Using Device Tree in place at 0000000083100000, end 00000000831777a1

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.140-tegra (buildbrain@mobile-u64-3456) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f9197770
[    0.000000] Boot CPU: AArch64 Processor [411fd071]
[    0.000000] OF: fdt:memory scan node memory@80000000, reg size 48,
[    0.000000] OF: fdt: - 80000000 ,  7ee00000
[    0.000000] OF: fdt: - 100000000 ,  7f200000
[    0.000000] Found tegra_fbmem: 00800000@92cb4000
[    0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '')
[    0.000000] bootconsole [uart8250] enabled
[0000.159] [L4T TegraBoot] (version 00.00.2018.01-l4t-80a468da)
[0000.165] Processing in cold boot mode Bootloader 2
[0000.169] A02 Bootrom Patch rev = 1023
[0000.173] Power-up reason: software reset
[0000.177] No Battery Present
[0000.179] pmic max77620 reset reason
[0000.183] pmic max77620 NVERC : 0x0
[0000.186] RamCode = 0
[0000.188] Platform has DDR4 type RAM
[0000.192] max77620 disabling SD1 Remote Sense
[0000.196] Setting DDR voltage to 1125mv
[0000.200] Serial Number of Pmic Max77663: 0x3219e8
[0000.208] Entering ramdump check
[0000.211] Get RamDumpCarveOut = 0x0
[0000.214] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0000.219] Last reboot was clean, booting normally!
[0000.224] Sdram initialization is successful
[0000.228] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.234] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.240] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.245] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.251] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.257] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.263] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.269] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.285] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.291] Platform-DebugCarveout: 0
[0000.294] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.300] Non secure mode, and RB not enabled.
[0000.304] Read GPT from (4:0)
[0000.596] Csd NumOfBlocks=125042688
[0000.601] Set High speed to 1
[0000.610] Using GPT Primary to query partitions
[0000.615] Loading Tboot-CPU binary
[0000.625] Verifying TBC in OdmNonSecureSBK mode
[0000.635] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.642] Bootloader downloaded successfully.
[0000.646] Downloaded Tboot-CPU binary to 0xa0000258
[0000.651] MAX77620_GPIO5 configured
[0000.654] CPU power rail is up
[0000.657] CPU clock enabled
[0000.661] Performing RAM repair
[0000.664] Updating A64 Warmreset Address to 0xa00002e9
[0000.669] Loading NvTbootBootloaderDTB
[0000.693] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0000.759] Bootloader DTB Load Address: 0x83000000
[0000.763] Loading NvTbootKernelDTB
[0000.787] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0000.852] Kernel DTB Load Address: 0x83100000
[0000.857] Loading cboot binary
[0000.887] Verifying EBT in OdmNonSecureSBK mode
[0000.928] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0000.935] Bootloader downloaded successfully.
[0000.940] Read PT from (2:0)
[0000.955] Using BFS PT to query partitions
[0000.959] PT: Partition NCT NOT found !
[0000.963] Warning: Find Partition via PT Failed
[0000.967] Next binary entry address: 0x92c00258
[0000.972] BoardId: 3448
[0000.977] Overriding pmu board id with proc board id
[0000.981] Display board id is not available
[0001.009] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0001.061] /bpmp deleted
[0001.064] SC7EntryFw header found loaded at 0xff700000
[0001.254] OVR2 PMIC
[0001.256] Bpmp FW successfully loaded
[0001.260] WB0 init successfully at 0xff780000
[0001.264] Set NvDecSticky Bits
[0001.268] GSC2 address ff53fffc value c0edbbcc
[0001.274] GSC MC Settings done
[0001.277] TOS Image length 53680
[0001.280]  Monitor size 53680
[0001.283]  OS size 0
[0001.290] Secure Os AES-CMAC Verification Success!
[0001.295] TOS image cipher info: plaintext
[0001.299] Loading and Validation of Secure OS Successful
[0001.315] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.319] NvTbootPackSdramParams: start.
[0001.324] NvTbootPackSdramParams: done.
[0001.328] Tegraboot started after 87447 us
[0001.332] Basic modules init took 922334 us
[0001.336] Sec Bootdevice Read Time = 12 ms, Read Size = 65 KB
[0001.342] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0001.347] Storage Device Read Time = 108 ms, Read Size = 2241 KB
[0001.353] Storage Device Write Time = 0 ms, Write Size = 0 KB
[0001.358] Next stage binary read took 24383 us
[0001.363] Carveout took -36066 us
[0001.366] CPU initialization took 362402 us
[0001.370] Total time taken by TegraBoot 1273053 us

[0001.375] Starting CPU & Halting co-processor

64NOTICE:  BL31: v1.3(release):41d46a9cf
NOTICE:  BL31: Built : 15:55:29, Aug  3 2020
ERROR:   Error initializing runtime service trusty_fast
[0001.497] RamCode = 0
[0001.501] LPDDR4 Training: Read DT: Number of tables = 2
[0001.506] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0001.519] EMC Training Successful
[0001.522] 408000 not found in DVFS table
[0001.529] RamCode = 0
[0001.532] DT Write: emc-table@204000 succeeded
[0001.538] DT Write: emc-table@1600000 succeeded
[0001.542] LPDDR4 Training: Write DT: Number of tables = 2
[0001.588]
[0001.589] Debug Init done
[0001.591] Marked DTB cacheable
[0001.594] Bootloader DTB loaded at 0x83000000
[0001.599] Marked DTB cacheable
[0001.602] Kernel DTB loaded at 0x83100000
[0001.606] DeviceTree Init done
[0001.619] Pinmux applied successfully
[0001.623] gicd_base: 0x50041000
[0001.627] gicc_base: 0x50042000
[0001.630] Interrupts Init done
[0001.634] Using base:0x60005090 & irq:208 for tick-timer
[0001.639] Using base:0x60005098 for delay-timer
[0001.643] platform_init_timer: DONE
[0001.647] Timer(tick) Init done
[0001.651] osc freq = 38400 khz
[0001.655]
[0001.656] Welcome to L4T Cboot
[0001.659]
[0001.660] Cboot Version: 00.00.2018.01-t210-3a7ad565
[0001.665] calling constructors
[0001.668] initializing heap
[0001.670] initializing threads
[0001.673] initializing timers
[0001.676] creating bootstrap completion thread
[0001.681] top of bootstrap2()
[0001.684] CPU: ARM Cortex A57
[0001.686] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0001.691] initializing platform
[0001.699] Manufacturer: MF = 0xc2, ID MSB = 0x25
[0001.703] ID LSB = 0x36, ID-CFI len = 194 bytes
[0001.708] Macronix QSPI chip present
[0001.711] SPI device register
[0001.714] init boot device
[0001.717] allocating memory for boot device(SPI)
[0001.721] registering boot device
[0001.731] sdmmc node status = okay
[0001.734] sdcard instance = 0
[0001.737] sdcard gpio handle 0x56
[0001.740] sdcard gpio pin 0xc9
[0001.743] sdcard gpio flags 0x0
[0001.746] vmmc-supply 0x99
[0001.748] Instance: 0
[0001.751] Allocating memory for context
[0001.754] enabling clock
[0001.757] sd card init
[0001.759] Check card present and stable
[0001.763] Send command 0
[0001.779] Send command 3
[0001.784] Set RCA for the card
[0001.786] Query card specific data by command 9
[0001.793] Parse CSD data
[0001.795] Send command 7
[0001.806] Calling sd device register
[0001.809] Init sdcard
[0001.811] Allocating memory for boot device
[0001.815] Registering user device
[0001.829] Enable APE clock
[0001.831] Un-powergate APE partition
[0001.835] of_register: registering tegra_udc to of_hal
[0001.840] of_register: registering inv20628-driver to of_hal
[0001.845] of_register: registering ads1015-driver to of_hal
[0001.851] of_register: registering lp8557-bl-driver to of_hal
[0001.857] of_register: registering bq2419x_charger to of_hal
[0001.862] of_register: registering bq27441_fuel_gauge to of_hal
[0001.874] gpio framework initialized
[0001.877] of_register: registering tca9539_gpio to of_hal
[0001.883] of_register: registering tca9539_gpio to of_hal
[0001.888] of_register: registering i2c_bus_driver to of_hal
[0001.894] of_register: registering i2c_bus_driver to of_hal
[0001.899] of_register: registering i2c_bus_driver to of_hal
[0001.905] pmic framework initialized
[0001.908] of_register: registering max77620_pmic to of_hal
[0001.914] regulator framework initialized
[0001.918] of_register: registering tps65132_bl_driver to of_hal
[0001.924] initializing target
[0001.929] gpio_driver_register: register 'tegra_gpio_driver' driver
[0001.938] board ID = D78, board SKU = 0
[0001.941] Skipping Z3!
[0001.946] fixed regulator driver initialized
[0001.963] initializing OF layer
[0001.966] NCK carveout not present
[0001.970] Skipping dts_overrides
[0001.974] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0001.991] I2C Bus Init done
[0001.993] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.004] I2C Bus Init done
[0002.006] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.017] I2C Bus Init done
[0002.019] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.030] I2C Bus Init done
[0002.032] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.043] I2C Bus Init done
[0002.045] of_children_init: Ops found for compatible string maxim,max77620
[0002.056] max77620_init using irq 118
[0002.061] register 'maxim,max77620' pmic
[0002.065] gpio_driver_register: register 'max77620-gpio' driver
[0002.071] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.082] I2C Bus Init done
[0002.085] NCK carveout not present
[0002.095] Find /i2c@7000c000's alias i2c0
[0002.099] get eeprom at 1-a0, size 256, type 0
[0002.108] Find /i2c@7000c500's alias i2c2
[0002.112] get eeprom at 3-a0, size 256, type 0
[0002.116] get eeprom at 3-ae, size 256, type 0
[0002.121] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.126] I2C slave not started
[0002.129] I2C write failed
[0002.132] Writing offset failed
[0002.135] eeprom_init: EEPROM read failed
[0002.139] pm_ids_update: eeprom init failed
[0002.143] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.173] pm_ids_update: The pm board id is 3448-0000-200
[0002.179] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0002.187] pm_ids_update: pm id update successful
[0002.192] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.222] pm_ids_update: The pm board id is 3449-0000-200
[0002.228] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0002.236] pm_ids_update: pm id update successful
[0002.267] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.273] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0002.281] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.287] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0002.296] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:8c:b1
[0002.302] Plugin Manager: Parse ODM data 0x00094000
[0002.312] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000
[0002.327] Find /i2c@7000c000's alias i2c0
[0002.331] get eeprom at 1-a0, size 256, type 0
[0002.339] Find /i2c@7000c500's alias i2c2
[0002.343] get eeprom at 3-a0, size 256, type 0
[0002.348] get eeprom at 3-ae, size 256, type 0
[0002.352] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.357] I2C slave not started
[0002.360] I2C write failed
[0002.363] Writing offset failed
[0002.366] eeprom_init: EEPROM read failed
[0002.370] pm_ids_update: eeprom init failed
[0002.374] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.404] pm_ids_update: The pm board id is 3448-0000-200
[0002.411] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0002.418] pm_ids_update: pm id update successful
[0002.422] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.452] pm_ids_update: The pm board id is 3449-0000-200
[0002.459] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0002.466] pm_ids_update: pm id update successful
[0002.497] Add serial number:1422519063333 as DT property
[0002.504] Applying platform configs
[0002.511] platform-init is not present. Skipping
[0002.515] calling apps_init()
[0002.541] Found 12 GPT partitions in "sd0"
[0002.545] Proceeding to Cold Boot
[0002.548] starting app android_boot_app
[0002.552] Device state: unlocked
[0002.555] display console init
[0002.563] could not find regulator
[0002.567] hdmi cable connected
[0002.582] edid read success
[0002.600] DT entry for leds-pwm not found
[0002.604] edid read success
[0002.606] width = 640, height = 480, frequency = 25174825
[0002.612] width = 640, height = 480, frequency = 25174825
[0002.617] width = 640, height = 480, frequency = 25174825
[0002.622] width = 1920, height = 1080, frequency = 148500000
[0002.628] width = 1920, height = 1080, frequency = 174500000
[0002.634] width = 1280, height = 720, frequency = 74250000
[0002.639] width = 640, height = 480, frequency = 25174825
[0002.644] width = 720, height = 480, frequency = 26973026
[0002.650] width = 720, height = 480, frequency = 26973026
[0002.655] width = 1280, height = 720, frequency = 74175824
[0002.661] width = 720, height = 576, frequency = 26973026
[0002.666] width = 720, height = 576, frequency = 26973026
[0002.671] width = 1280, height = 720, frequency = 74175824
[0002.677] width = 1920, height = 1080, frequency = 148351648
[0002.683] width = 1920, height = 1080, frequency = 148351648
[0002.688] Best mode Width = 1920, Height = 1080, freq = 148351648
[0002.696] tmds-config node not found
[0002.700] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts
[0002.715] setting 'vdd-1v8' regulator to 1800000 micro volts
[0002.722] could not find regulator
[0002.726] could not find regulator
[0002.729] could not find regulator
[0002.757] using default cmu settings
[0002.761] dc_hdmi_enable, starting HDMI initialisation
[0002.767] dc_hdmi_enable, HDMI initialisation complete
[0002.772] list and configure display window
[0002.781] display console init completed
[0002.792] subnode volume_up is not found !
[0002.796] subnode back is not found !
[0002.800] subnode volume_down is not found !
[0002.804] subnode menu is not found !
[0002.807] Gpio keyboard init success
[0002.851] found decompressor handler: lz4-legacy
[0002.866] decompressing blob (type 1)...
[0002.901] load_bmp_blob: panelresolution=1080 type=3
[0002.952] decompressor handler not found
[0002.956] load_firmware_blob: Firmware blob loaded, entries=2
[0002.962] -------> se_aes_verify_sbk_clear: 747
[0002.966] se_aes_verify_sbk_clear: Error
[0002.970] bl_battery_charging: connected to external power supply
[0002.977] xusb is supported
[0002.983] error while finding nvidia,portmap
[0003.487] xusb blob version 0 size 124416
[0003.491] firmware size 124416
[0003.496] Firmware timestamp: 0x5da88fc3, Version: 50.25 release
[0003.506] xhci0: 64 bytes context size, 32-bit DMA
[0003.546] usbus0: 5.0Gbps Super Speed USB v3.0
[0003.566] uhub0: <Nvidia XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
[0004.216] uhub0: 9 ports with 9 removable, self powered
[0005.216] failed to get HID devices
[0005.220] failed to init xhci or no usb device attached
[0005.230] device_query_partition_size: failed to open partition sd0:MSC !
[0005.237] MSC Partition not found
[0005.243] device_query_partition_size: failed to open partition sd0:USP !
[0005.250] USP partition read failed!
[0005.253] blob_init: blob-partition USP header read failed
[0005.259] android_boot Unable to update recovery partition
[0005.264] kfs_getpartname: name = LNX
[0005.268] Loading kernel from LNX
[0005.367] load kernel from storage
[0005.378] decompressor handler not found
[0005.436] Successfully loaded kernel and ramdisk images
[0005.442] load_bmp_blob: panelresolution=1080 type=3
[0005.937] display bmp image done
[0005.940] NCK carveout not present
[0005.943] Skipping dts_overrides
[0005.946] NCK carveout not present
[0005.956] Find /i2c@7000c000's alias i2c0
[0005.960] get eeprom at 1-a0, size 256, type 0
[0005.969] Find /i2c@7000c500's alias i2c2
[0005.973] get eeprom at 3-a0, size 256, type 0
[0005.977] get eeprom at 3-ae, size 256, type 0
[0005.982] pm_ids_update: Updating 1,a0, size 256, type 0
[0005.987] I2C slave not started
[0005.990] I2C write failed
[0005.993] Writing offset failed
[0005.996] eeprom_init: EEPROM read failed
[0006.000] pm_ids_update: eeprom init failed
[0006.004] pm_ids_update: Updating 3,a0, size 256, type 0
[0006.034] pm_ids_update: The pm board id is 3448-0000-200
[0006.041] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0006.048] pm_ids_update: pm id update successful
[0006.053] pm_ids_update: Updating 3,ae, size 256, type 0
[0006.083] pm_ids_update: The pm board id is 3449-0000-200
[0006.089] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0006.097] pm_ids_update: pm id update successful
[0006.128] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0006.134] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0006.142] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0006.148] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0006.156] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e6:8c:b1
[0006.163] Plugin Manager: Parse ODM data 0x00094000
[0006.173] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000
[0006.181] Add serial number:1422519063333 as DT property
[0006.190] "bpmp" doesn't exist, creating
[0006.195] Updated bpmp info to DTB
[0006.200] Updated initrd info to DTB
[0006.204] "proc-board" doesn't exist, creating
[0006.209] Updated board info to DTB
[0006.213] "pmu-board" doesn't exist, creating
[0006.218] Updated board info to DTB
[0006.222] "display-board" doesn't exist, creating
[0006.227] Updated board info to DTB
[0006.231] "reset" doesn't exist, creating
[0006.235] Updated reset info to DTB
[0006.239] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video
[0006.277] DTB cmdline: earlycon=uart8250,mmio32,0x70006000
[0006.283] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
[0006.296] Updated bootarg info to DTB
[0006.300] Adding uuid 00000001644495811c00000003ff8400 to DT
[0006.306] Adding eks info 0 to DT
[0006.311] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7
[0006.317] Updated memory info to DTB
[0006.323] Updated system-lp0-disable info to DTB
[0006.331] set vdd_core voltage to 1075 mv
[0006.335] setting 'vdd-core' regulator to 1075000 micro volts
[0006.356] Found secure-pmc; disable BPMP


U-Boot 2016.07-ge6da093be3 (Aug 03 2020 - 15:55:24 -0700)

TEGRA210
Model: NVIDIA P3450-Porg
Board: NVIDIA P3450-PORG
DRAM:  4 GiB
MMC:   Tegra SD/MMC: 0, Tegra SD/MMC: 1
SF: Detected MX25U3235F with page size 256 Bytes, erase size 4 KiB, total 4 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0