=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2020.08.29 20:55:21 =~=~=~=~=~=~=~=~=~=~=~= [0000.221] [L4T TegraBoot] (version 00.00.2018.01-l4t-80a468da) [0000.226] Processing in cold boot mode Bootloader 2 [0000.231] A02 Bootrom Patch rev = 1023 [0000.235] Power-up reason: pmc por [0000.238] No Battery Present [0000.240] pmic max77620 reset reason [0000.244] pmic max77620 NVERC : 0x40 [0000.247] RamCode = 0 [0000.249] Platform has DDR4 type RAM [0000.253] max77620 disabling SD1 Remote Sense [0000.257] Setting DDR voltage to 1125mv [0000.261] Serial Number of Pmic Max77663: 0x205ad [0000.268] Entering ramdump check [0000.271] Get RamDumpCarveOut = 0x0 [0000.275] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.280] Last reboot was clean, booting normally! [0000.284] Sdram initialization is successful [0000.289] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.295] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.300] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.306] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.312] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.318] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.324] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.330] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.346] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.352] Platform-DebugCarveout: 0 [0000.355] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.361] Non secure mode, and RB not enabled. [0000.378] Csd NumOfBlocks=0 [0000.569] *** Booting BFS0. [0000.572] Read PT from (0:3) [0000.578] Using BFS PT to query partitions [0000.582] PT: Partition LNX NOT found ! [0001.165] *** Booting KFS0. [0001.168] Read GPT from (0:3) [0001.172] Using GPT Primary to query partitions [0001.177] Loading Tboot-CPU binary [0001.184] Verifying TBC in OdmNonSecureSBK mode [0001.194] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0001.201] Bootloader downloaded successfully. [0001.205] Downloaded Tboot-CPU binary to 0xa0000258 [0001.210] MAX77620_GPIO5 configured [0001.213] CPU power rail is up [0001.216] CPU clock enabled [0001.220] Performing RAM repair [0001.223] Updating A64 Warmreset Address to 0xa00002e9 [0001.228] Loading NvTbootBootloaderDTB [0001.245] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0001.311] Bootloader DTB Load Address: 0x83000000 [0001.315] Loading NvTbootKernelDTB [0001.332] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0001.397] Kernel DTB Load Address: 0x83100000 [0001.403] Loading cboot binary [0001.413] Verifying EBT in OdmNonSecureSBK mode [0001.455] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0001.462] Bootloader downloaded successfully. [0001.467] PT: Partition NCT NOT found ! [0001.470] Warning: Find Partition via PT Failed [0001.475] Next binary entry address: 0x92c00258 [0001.479] BoardId: 3448 [0001.484] Overriding pmu board id with proc board id [0001.488] Display board id is not available [0001.500] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.552] /bpmp deleted [0001.554] SC7EntryFw header found loaded at 0xff700000 [0001.744] OVR2 PMIC [0001.746] Bpmp FW successfully loaded [0001.751] WB0 init successfully at 0xff780000 [0001.755] Set NvDecSticky Bits [0001.759] GSC2 address ff53fffc value c0edbbcc [0001.765] GSC MC Settings done [0001.769] TOS Image length 53680 [0001.772] Monitor size 53680 [0001.775] OS size 0 [0001.780] Secure Os AES-CMAC Verification Success! [0001.784] TOS image cipher info: plaintext [0001.788] Loading and Validation of Secure OS Successful [0001.804] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.809] NvTbootPackSdramParams: start. [0001.814] NvTbootPackSdramParams: done. [0001.818] Tegraboot started after 150381 us [0001.822] Basic modules init took 1378888 us [0001.826] Sec Bootdevice Read Time = 542 ms, Read Size = 14457 KB [0001.832] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.837] Next stage binary read took 7376 us [0001.841] Carveout took -19279 us [0001.844] CPU initialization took 344349 us [0001.848] Total time taken by TegraBoot 1711334 us [0001.853] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):41d46a9cf NOTICE: BL31: Built : 21:18:12, Jun 25 2020 ERROR: Error initializing runtime service trusty_fast [0001.975] RamCode = 0 [0001.980] LPDDR4 Training: Read DT: Number of tables = 2 [0001.985] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.998] EMC Training Successful [0002.001] 408000 not found in DVFS table [0002.007] RamCode = 0 [0002.011] DT Write: emc-table@204000 succeeded [0002.016] DT Write: emc-table@1600000 succeeded [0002.021] LPDDR4 Training: Write DT: Number of tables = 2 [0002.078] [0002.079] Debug Init done [0002.081] Marked DTB cacheable [0002.084] Bootloader DTB loaded at 0x83000000 [0002.089] Marked DTB cacheable [0002.092] Kernel DTB loaded at 0x83100000 [0002.096] DeviceTree Init done [0002.109] Pinmux applied successfully [0002.113] gicd_base: 0x50041000 [0002.116] gicc_base: 0x50042000 [0002.119] Interrupts Init done [0002.124] Using base:0x60005090 & irq:208 for tick-timer [0002.129] Using base:0x60005098 for delay-timer [0002.133] platform_init_timer: DONE [0002.137] Timer(tick) Init done [0002.140] osc freq = 38400 khz [0002.145] [0002.146] Welcome to L4T Cboot [0002.149] [0002.150] Cboot Version: 00.00.2018.01-t210-3a7ad565 [0002.155] calling constructors [0002.158] initializing heap [0002.160] initializing threads [0002.163] initializing timers [0002.166] creating bootstrap completion thread [0002.171] top of bootstrap2() [0002.173] CPU: ARM Cortex A57 [0002.176] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0002.181] initializing platform [0002.235] Config for emmc ddr50 mode completed [0002.239] sdmmc bdev is already initialized [0002.243] Enable APE clock [0002.246] Un-powergate APE partition [0002.249] of_register: registering tegra_udc to of_hal [0002.255] of_register: registering inv20628-driver to of_hal [0002.260] of_register: registering ads1015-driver to of_hal [0002.266] of_register: registering lp8557-bl-driver to of_hal [0002.271] of_register: registering bq2419x_charger to of_hal [0002.277] of_register: registering bq27441_fuel_gauge to of_hal [0002.289] gpio framework initialized [0002.292] of_register: registering tca9539_gpio to of_hal [0002.297] of_register: registering tca9539_gpio to of_hal [0002.303] of_register: registering i2c_bus_driver to of_hal [0002.308] of_register: registering i2c_bus_driver to of_hal [0002.314] of_register: registering i2c_bus_driver to of_hal [0002.319] pmic framework initialized [0002.323] of_register: registering max77620_pmic to of_hal [0002.328] regulator framework initialized [0002.332] of_register: registering tps65132_bl_driver to of_hal [0002.338] initializing target [0002.344] gpio_driver_register: register 'tegra_gpio_driver' driver [0002.352] board ID = D78, board SKU = 2 [0002.358] fixed regulator driver initialized [0002.376] initializing OF layer [0002.379] NCK carveout not present [0002.382] Skipping dts_overrides [0002.386] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.403] I2C Bus Init done [0002.406] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.416] I2C Bus Init done [0002.419] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.429] I2C Bus Init done [0002.432] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.442] I2C Bus Init done [0002.445] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.455] I2C Bus Init done [0002.458] of_children_init: Ops found for compatible string maxim,max77620 [0002.468] max77620_init using irq 118 [0002.473] register 'maxim,max77620' pmic [0002.477] gpio_driver_register: register 'max77620-gpio' driver [0002.484] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.494] I2C Bus Init done [0002.498] NCK carveout not present [0002.508] Find /i2c@7000c000's alias i2c0 [0002.511] get eeprom at 1-a0, size 256, type 0 [0002.520] Find /i2c@7000c500's alias i2c2 [0002.524] get eeprom at 3-a0, size 256, type 0 [0002.529] get eeprom at 3-ae, size 256, type 0 [0002.533] pm_ids_update: Updating 1,a0, size 256, type 0 [0004.538] I2C transfer timeout [0004.541] I2C write failed [0004.544] Writing offset failed [0004.547] eeprom_init: EEPROM read failed [0004.551] pm_ids_update: eeprom init failed [0004.555] pm_ids_update: Updating 3,a0, size 256, type 0 [0006.560] I2C transfer timeout [0006.563] I2C write failed [0006.566] Writing offset failed [0006.569] eeprom_init: EEPROM read failed [0006.573] pm_ids_update: eeprom init failed [0006.577] pm_ids_update: Updating 3,ae, size 256, type 0 [0008.582] I2C transfer timeout [0008.585] I2C write failed [0008.588] Writing offset failed [0008.591] eeprom_init: EEPROM read failed [0008.595] pm_ids_update: eeprom init failed [0010.599] I2C transfer timeout [0010.602] I2C write failed [0010.605] Writing offset failed [0010.608] eeprom_init: EEPROM read failed [0010.612] Plugin Manager: Parse ODM data 0x00094000 [0010.622] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0010.636] Find /i2c@7000c000's alias i2c0 [0010.640] get eeprom at 1-a0, size 256, type 0 [0010.649] Find /i2c@7000c500's alias i2c2 [0010.653] get eeprom at 3-a0, size 256, type 0 [0010.658] get eeprom at 3-ae, size 256, type 0 [0010.662] pm_ids_update: Updating 1,a0, size 256, type 0 [0012.667] I2C transfer timeout [0012.670] I2C write failed [0012.673] Writing offset failed [0012.676] eeprom_init: EEPROM read failed [0012.680] pm_ids_update: eeprom init failed [0012.684] pm_ids_update: Updating 3,a0, size 256, type 0 [0014.689] I2C transfer timeout [0014.692] I2C write failed [0014.695] Writing offset failed [0014.698] eeprom_init: EEPROM read failed [0014.702] pm_ids_update: eeprom init failed [0014.706] pm_ids_update: Updating 3,ae, size 256, type 0 [0016.711] I2C transfer timeout [0016.714] I2C write failed [0016.717] Writing offset failed [0016.720] eeprom_init: EEPROM read failed [0016.724] pm_ids_update: eeprom init failed [0018.728] I2C transfer timeout [0018.731] I2C write failed [0018.734] Writing offset failed [0018.737] eeprom_init: EEPROM read failed [0018.741] shim_get_serial_num:EEPROM read failed [0018.745] Reading Serial number from with NCT/FCT [0018.750] No serial number in NCT/EEPROM. Using fused IDs [0018.755] Chip UID is 00000001644608400c00000011070300 [0018.760] Add serial number:000307110000000c4008 as DT property [0018.769] Applying platform configs [0018.775] platform-init is not present. Skipping [0018.780] calling apps_init() [0018.796] Found 17 GPT partitions in "sdmmc3_user" [0018.800] Proceeding to Cold Boot [0018.804] starting app android_boot_app [0018.807] Device state: unlocked [0018.811] display console init [0018.819] could not find regulator [0018.822] hdmi cable connected [0018.860] DT entry for leds-pwm not found [0020.833] I2C transfer timeout [0020.836] I2C write failed [0020.838] Writing offset failed [0020.841] could not read edid [0020.846] tmds-config node not found [0020.850] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0020.865] setting 'vdd-1v8' regulator to 1800000 micro volts [0020.872] could not find regulator [0020.876] could not find regulator [0020.879] could not find regulator [0020.907] using default cmu settings [0020.911] dc_hdmi_enable, starting HDMI initialisation [0020.917] dc_hdmi_enable, HDMI initialisation complete [0020.922] list and configure display window [0020.927] display console init completed [0020.934] subnode volume_up is not found ! [0020.938] subnode back is not found ! [0020.942] subnode volume_down is not found ! [0020.946] subnode menu is not found ! [0020.950] Gpio keyboard init success [0020.997] found decompressor handler: lz4-legacy [0021.011] decompressing blob (type 1)... [0021.045] load_bmp_blob: panelresolution=480 type=0 [0021.095] decompressor handler not found [0021.099] load_firmware_blob: Firmware blob loaded, entries=2 [0021.104] -------> se_aes_verify_sbk_clear: 747 [0021.109] se_aes_verify_sbk_clear: Error [0021.113] bl_battery_charging: connected to external power supply [0021.120] xusb is supported [0021.126] error while finding nvidia,portmap [0021.630] xusb blob version 0 size 124416 [0021.634] firmware size 124416 [0021.639] Firmware timestamp: 0x5da88fc3, Version: 50.25 release [0021.646] xhci0: 64 bytes context size, 32-bit DMA [0021.686] usbus0: 5.0Gbps Super Speed USB v3.0 [0021.706] uhub0: on usbus0 [0022.356] uhub0: 9 ports with 9 removable, self powered [0023.356] failed to get HID devices [0023.360] failed to init xhci or no usb device attached [0023.374] device_query_partition_size: failed to open partition sdmmc3_user:MSC ! [0023.381] MSC Partition not found [0023.391] device_query_partition_size: failed to open partition sdmmc3_user:USP ! [0023.398] USP partition read failed! [0023.401] blob_init: blob-partition USP header read failed [0023.407] android_boot Unable to update recovery partition [0023.412] kfs_getpartname: name = LNX [0023.416] Loading kernel from LNX [0023.480] load kernel from storage [0023.489] decompressor handler not found [0023.508] Successfully loaded kernel and ramdisk images [0023.515] load_bmp_blob: panelresolution=480 type=0 [0023.588] display bmp image done [0023.591] NCK carveout not present [0023.595] Skipping dts_overrides [0023.598] NCK carveout not present [0023.608] Find /i2c@7000c000's alias i2c0 [0023.612] get eeprom at 1-a0, size 256, type 0 [0023.621] Find /i2c@7000c500's alias i2c2 [0023.625] get eeprom at 3-a0, size 256, type 0 [0023.629] get eeprom at 3-ae, size 256, type 0 [0023.633] pm_ids_update: Updating 1,a0, size 256, type 0 [0025.639] I2C transfer timeout [0025.642] I2C write failed [0025.644] Writing offset failed [0025.647] eeprom_init: EEPROM read failed [0025.651] pm_ids_update: eeprom init failed [0025.655] pm_ids_update: Updating 3,a0, size 256, type 0 [0027.661] I2C transfer timeout [0027.664] I2C write failed [0027.666] Writing offset failed [0027.669] eeprom_init: EEPROM read failed [0027.673] pm_ids_update: eeprom init failed [0027.677] pm_ids_update: Updating 3,ae, size 256, type 0 [0029.683] I2C transfer timeout [0029.686] I2C write failed [0029.688] Writing offset failed [0029.691] eeprom_init: EEPROM read failed [0029.695] pm_ids_update: eeprom init failed [0031.700] I2C transfer timeout [0031.702] I2C write failed [0031.705] Writing offset failed [0031.708] eeprom_init: EEPROM read failed [0031.712] Plugin Manager: Parse ODM data 0x00094000 [0031.722] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0031.730] Add serial number:000307110000000c4008 as DT property [0031.740] "bpmp" doesn't exist, creating [0031.745] Updated bpmp info to DTB [0031.750] Updated initrd info to DTB [0031.754] "proc-board" doesn't exist, creating [0031.759] Updated board info to DTB [0031.763] "pmu-board" doesn't exist, creating [0031.768] Updated board info to DTB [0031.771] "display-board" doesn't exist, creating [0031.777] Updated board info to DTB [0031.780] "reset" doesn't exist, creating [0031.785] Updated reset info to DTB [0031.788] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 tegra_fbmem=0x140000@0x92cb0000 is_hdmi_initialised=1 [0031.827] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0031.833] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 [0031.849] Updated bootarg info to DTB [0031.853] Adding uuid 00000001644608400c00000011070300 to DT [0031.858] Adding eks info 0 to DT [0031.864] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0031.870] Updated memory info to DTB [0031.875] add_lp0_disable: Unable to find plugin-manager ids under chosen node! (FDT_ERR_NOTFOUND) [0031.887] set vdd_core voltage to 1125 mv [0031.891] setting 'vdd-core' regulator to 1125000 micro volts [0031.916] Found secure-pmc; disable BPMP U-Boot 2016.07 (Aug 29 2020 - 17:24:11 -0400) TEGRA210 Model: NVIDIA P3450-Porg Board: NVIDIA P3450-PORG DRAM: 4 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000 *** Warning - spi_flash_probe() failed, using default environment In: serial Out: serial Err: serial Can't find nvidia,ethernet-mac property in CBoot DTB Net: No ethernet found. MMC: no card present ** Bad device mmc 1 ** Hit any key to stop autoboot: 1  0 MMC: no card present switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 878 bytes read in 74 ms (10.7 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 5488163 bytes read in 224 ms (23.4 MiB/s) Retrieving file: /boot/Image 34330632 bytes read in 810 ms (40.4 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,2 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 tegra_fbmem=0x140000@0x92cb0000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 sdhci_tegra.en_boot_part_access=1 ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 reserving fdt memory region: addr=80000000 size=20000 Using Device Tree in place at 0000000083100000, end 0000000083177727 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.140-tegra (turro@turro-G3-3779) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #5 SMP PREEMPT Sat Aug 29 19:35:46 EDT 2020 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 48, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00140000@92cb0000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 2.225903] tegra-vii2c 546c0000.i2c: --- register dump for debugging ---- [ 2.232790] tegra-vii2c 546c0000.i2c: I2C_CNFG - 0x22c00 [ 2.238103] tegra-vii2c 546c0000.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [ 2.244977] tegra-vii2c 546c0000.i2c: I2C_FIFO_CONTROL - 0xe0 [ 2.250720] tegra-vii2c 546c0000.i2c: I2C_FIFO_STATUS - 0x800070 [ 2.256724] tegra-vii2c 546c0000.i2c: I2C_INT_MASK - 0xac [ 2.262122] tegra-vii2c 546c0000.i2c: I2C_INT_STATUS - 0x0 [ 2.267604] tegra-vii2c 546c0000.i2c: msg->len - 3 [ 2.272393] tegra-vii2c 546c0000.i2c: is_msg_write - 1 [ 2.277528] tegra-vii2c 546c0000.i2c: buf_remaining - 0 [ 2.282754] tegra-vii2c 546c0000.i2c: i2c transfer timed out, addr 0x0040, data 0x00 [ 2.290556] ina3221x 6-0040: ina3221 reset failure status: 0xffffff92 [ 2.363665] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): bad mac address at /chosen/nvidia,ethernet-mac: missing. [ 11.121905] tegra-i2c 7000c700.i2c: rx dma timeout txlen:28 rxlen:128 [ 11.128354] tegra-i2c 7000c700.i2c: --- register dump for debugging ---- [ 11.135066] tegra-i2c 7000c700.i2c: I2C_CNFG - 0x22c00 [ 11.140203] tegra-i2c 7000c700.i2c: I2C_PACKET_TRANSFER_STATUS - 0x10001 [ 11.146900] tegra-i2c 7000c700.i2c: I2C_FIFO_CONTROL - 0x1c [ 11.152470] tegra-i2c 7000c700.i2c: I2C_FIFO_STATUS - 0x800040 [ 11.158300] tegra-i2c 7000c700.i2c: I2C_INT_MASK - 0x6c [ 11.163523] tegra-i2c 7000c700.i2c: I2C_INT_STATUS - 0x2 [ 11.168858] tegra-i2c 7000c700.i2c: i2c transfer timed out addr: 0x50 [ 11.176673] tegradc tegradc.1: dpd enable lookup fail:-19 [ 11.257885] Unable to handle kernel read from unreadable memory at virtual address 000001d8 [ 11.266241] Mem abort info: [ 11.269027] ESR = 0x96000005 [ 11.272087] Exception class = DABT (current EL), IL = 32 bits [ 11.281129] SET = 0, FnV = 0 [ 11.284201] EA = 0, S1PTW = 0 [ 11.287343] Data abort info: [ 11.290227] ISV = 0, ISS = 0x00000005 [ 11.294062] CM = 0, WnR = 0 [ 11.297022] [00000000000001d8] user address but active_mm is swapper [ 11.303376] Internal error: Oops: 96000005 [#1] PREEMPT SMP [ 11.308937] Modules linked in: [ 11.311994] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.9.140-tegra #5 [ 11.318510] Hardware name: NVIDIA Jetson Nano Developer Kit (DT) [ 11.324503] task: ffffffc0fa6f0000 task.stack: ffffffc0fa66c000 [ 11.330416] PC is at tegra_channel_populate_dev_info+0xac/0x190 [ 11.336325] LR is at tegra_channel_populate_dev_info+0x9c/0x190 [ 11.342233] pc : [] lr : [] pstate: 40400045 [ 11.349613] sp : ffffffc0fa66f850 [ 11.352919] x29: ffffffc0fa66f850 x28: ffffff8009824da0 [ 11.358236] x27: ffffff8009669010 x26: 0000000000000001 [ 11.363550] x25: 00000000009a2065 x24: ffffffc0f51ac038 [ 11.368864] x23: 000000000000000b x22: ffffffc0f508f1e8 [ 11.374178] x21: ffffffc0f508f018 x20: ffffffc0fa66f8f8 [ 11.379491] x19: ffffffc0f94b3c10 x18: 0000000000000001 [ 11.384804] x17: 0000000000000005 x16: 0000000000000000 [ 11.390118] x15: ffffffffffffffff x14: ffffffc0fa66f850 [ 11.395431] x13: ffffffc0fa66f755 x12: ffffffffffffffff [ 11.400746] x11: ffffffc0fa66f710 x10: ffffffc0fa66f710 [ 11.406061] x9 : 0000000000000002 x8 : 0000000000000002 [ 11.411375] x7 : ffffff8008fc6e88 x6 : 0000000000000090 [ 11.416688] x5 : 000000000000008d x4 : 0000000000000001 [ 11.422002] x3 : 0000000000000000 x2 : 0000000000000000 [ 11.427315] x1 : 0000000000000000 x0 : 0000000000000000 [ 11.432628] [ 11.434113] Process swapper/0 (pid: 1, stack limit = 0xffffffc0fa66c000) [ 11.440800] Call trace: [ 11.443242] [] tegra_channel_populate_dev_info+0xac/0x190 [ 11.450192] [] tegra_channel_init_subdevices+0x2e8/0x790 [ 11.457054] [] tegra_vi_graph_notify_complete+0x2e8/0x6e0 [ 11.464003] [] v4l2_async_test_notify+0x104/0x120 [ 11.470258] [] v4l2_async_notifier_register+0x128/0x198 [ 11.477034] [] tegra_vi_graph_init+0x234/0x288 [ 11.483029] [] tegra_vi_media_controller_init+0x1d0/0x208 [ 11.489979] [] vi_probe+0x378/0x520 [ 11.495021] [] platform_drv_probe+0x60/0xc0 [ 11.500756] [] driver_probe_device+0xd8/0x408 [ 11.506665] [] __driver_attach+0xdc/0x128 [ 11.512226] [] bus_for_each_dev+0x5c/0xa8 [ 11.517787] [] driver_attach+0x30/0x40 [ 11.523088] [] bus_add_driver+0x20c/0x2a8 [ 11.528649] [] driver_register+0x6c/0x110 [ 11.534209] [] __platform_driver_register+0x5c/0x68 [ 11.540639] [] vi_init+0x2c/0x38 [ 11.545420] [] do_one_initcall+0x44/0x130 [ 11.550983] [] kernel_init_freeable+0x1a0/0x244 [ 11.557066] [] kernel_init+0x18/0x108 [ 11.562280] [] ret_from_fork+0x10/0x30 [ 11.567584] ---[ end trace eedb9dac196e3fbc ]--- [ 11.578012] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b [ 11.578012] [ 11.587135] SMP: stopping secondary CPUs [ 11.591101] Kernel Offset: disabled [ 11.594582] Memory Limit: none [ 11.603346] Rebooting in 5 seconds..