[0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-e82258de) [0000.130] Processing in cold boot mode Bootloader 2 [0000.135] A02 Bootrom Patch rev = 1023 [0000.138] Power-up reason: pmc por [0000.141] No Battery Present [0000.144] pmic max77620 reset reason [0000.147] pmic max77620 NVERC : 0x40 [0000.151] RamCode = 0 [0000.153] Platform has DDR4 type RAM [0000.156] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0x1901ab [0000.172] Entering ramdump check [0000.175] Get RamDumpCarveOut = 0x0 [0000.179] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.188] Sdram initialization is successful [0000.192] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.199] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.204] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.210] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.234] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.256] Platform-DebugCarveout: 0 [0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.265] Non secure mode, and RB not enabled. [0000.269] BoardID = 3448, SKU = 0x0 [0000.272] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.276] Nano-SD: checking PT table on QSPI ... [0000.281] Read PT from (2:0) [0000.296] Using BFS PT to query partitions [0000.302] Loading Tboot-CPU binary [0000.330] Verifying TBC in OdmNonSecureSBK mode [0000.340] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.347] Bootloader downloaded successfully. [0000.351] Downloaded Tboot-CPU binary to 0xa0000258 [0000.356] MAX77620_GPIO5 configured [0000.359] CPU power rail is up [0000.362] CPU clock enabled [0000.366] Performing RAM repair [0000.369] Updating A64 Warmreset Address to 0xa00002e9 [0000.374] BoardID = 3448, SKU = 0x0 [0000.377] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.381] Nano-SD: checking PT table on QSPI ... [0000.385] Loading NvTbootBootloaderDTB [0000.452] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.525] Bootloader DTB Load Address: 0x83000000 [0000.530] BoardID = 3448, SKU = 0x0 [0000.533] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.537] Nano-SD: checking PT table on QSPI ... [0000.541] Loading NvTbootKernelDTB [0000.607] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.680] Kernel DTB Load Address: 0x83100000 [0000.684] BoardID = 3448, SKU = 0x0 [0000.688] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.692] Nano-SD: checking PT table on QSPI ... [0000.698] Loading cboot binary [0000.814] Verifying EBT in OdmNonSecureSBK mode [0000.855] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.862] Bootloader downloaded successfully. [0000.866] BoardID = 3448, SKU = 0x0 [0000.870] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.873] Nano-SD: checking PT table on QSPI ... [0000.878] PT: Partition NCT NOT found ! [0000.882] Warning: Find Partition via PT Failed [0000.886] Next binary entry address: 0x92c00258 [0000.891] BoardId: 3448 [0000.895] Overriding pmu board id with proc board id [0000.900] Display board id is not available [0000.904] BoardID = 3448, SKU = 0x0 [0000.907] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.911] Nano-SD: checking PT table on QSPI ... [0001.016] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.073] /bpmp deleted [0001.075] SC7EntryFw header found loaded at 0xff700000 [0001.271] OVR2 PMIC [0001.272] Bpmp FW successfully loaded [0001.276] BoardID = 3448, SKU = 0x0 [0001.279] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.283] Nano-SD: checking PT table on QSPI ... [0001.288] WB0 init successfully at 0xff780000 [0001.293] Set NvDecSticky Bits [0001.296] GSC2 address ff53fffc value c0edbbcc [0001.302] GSC MC Settings done [0001.305] BoardID = 3448, SKU = 0x0 [0001.309] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.312] Nano-SD: checking PT table on QSPI ... [0001.318] TOS Image length 53680 [0001.321] Monitor size 53680 [0001.324] OS size 0 [0001.339] Secure Os AES-CMAC Verification Success! [0001.343] TOS image cipher info: plaintext [0001.347] Loading and Validation of Secure OS Successful [0001.363] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.368] NvTbootPackSdramParams: start. [0001.373] NvTbootPackSdramParams: done. [0001.377] Tegraboot started after 51831 us [0001.381] Basic modules init took 886473 us [0001.385] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB [0001.390] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.396] Next stage binary read took 102861 us [0001.400] Carveout took -126357 us [0001.403] CPU initialization took 495390 us [0001.407] Total time taken by TegraBoot 1358367 us [0001.412] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):5b49e7f80 NOTICE: BL31: Built : 14:33:23, Jan 15 2021 ERROR: Error initializing runtime service trusty_fast [0001.534] RamCode = 0 [0001.539] LPDDR4 Training: Read DT: Number of tables = 2 [0001.544] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.557] EMC Training Successful [0001.560] 408000 not found in DVFS table [0001.566] RamCode = 0 [0001.570] DT Write: emc-table@204000 succeeded [0001.575] DT Write: emc-table@1600000 succeeded [0001.579] LPDDR4 Training: Write DT: Number of tables = 2 [0001.626] [0001.627] Debug Init done [0001.630] Marked DTB cacheable [0001.633] Bootloader DTB loaded at 0x83000000 [0001.638] Marked DTB cacheable [0001.640] Kernel DTB loaded at 0x83100000 [0001.644] DeviceTree Init done [0001.657] Pinmux applied successfully [0001.662] gicd_base: 0x50041000 [0001.665] gicc_base: 0x50042000 [0001.668] Interrupts Init done [0001.672] Using base:0x60005090 & irq:208 for tick-timer [0001.678] Using base:0x60005098 for delay-timer [0001.682] platform_init_timer: DONE [0001.685] Timer(tick) Init done [0001.689] osc freq = 38400 khz [0001.693] [0001.694] Welcome to L4T Cboot [0001.697] [0001.698] Cboot Version: 00.00.2018.01-t210-39562017 [0001.703] calling constructors [0001.706] initializing heap [0001.709] initializing threads [0001.712] initializing timers [0001.715] creating bootstrap completion thread [0001.719] top of bootstrap2() [0001.722] CPU: ARM Cortex A57 [0001.725] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.730] initializing platform [0001.737] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.742] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.746] Macronix QSPI chip present [0001.750] SPI device register [0001.752] init boot device [0001.755] allocating memory for boot device(SPI) [0001.760] registering boot device [0001.778] QSPI bdev is already initialized [0001.782] Enable APE clock [0001.785] Un-powergate APE partition [0001.788] of_register: registering tegra_udc to of_hal [0001.793] of_register: registering inv20628-driver to of_hal [0001.799] of_register: registering ads1015-driver to of_hal [0001.804] of_register: registering lp8557-bl-driver to of_hal [0001.810] of_register: registering bq2419x_charger to of_hal [0001.816] of_register: registering bq27441_fuel_gauge to of_hal [0001.827] gpio framework initialized [0001.831] of_register: registering tca9539_gpio to of_hal [0001.836] of_register: registering tca9539_gpio to of_hal [0001.841] of_register: registering i2c_bus_driver to of_hal [0001.847] of_register: registering i2c_bus_driver to of_hal [0001.853] of_register: registering i2c_bus_driver to of_hal [0001.858] pmic framework initialized [0001.862] of_register: registering max77620_pmic to of_hal [0001.867] regulator framework initialized [0001.871] of_register: registering tps65132_bl_driver to of_hal [0001.877] initializing target [0001.883] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.891] board ID = D78, board SKU = 0 [0001.895] Skipping Z3! [0001.899] fixed regulator driver initialized [0001.917] initializing OF layer [0001.920] NCK carveout not present [0001.924] Skipping dts_overrides [0001.928] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.945] I2C Bus Init done [0001.947] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.958] I2C Bus Init done [0001.960] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.971] I2C Bus Init done [0001.973] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.984] I2C Bus Init done [0001.986] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.997] I2C Bus Init done [0001.999] of_children_init: Ops found for compatible string maxim,max77620 [0002.010] max77620_init using irq 118 [0002.015] register 'maxim,max77620' pmic [0002.019] gpio_driver_register: register 'max77620-gpio' driver [0002.025] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.036] I2C Bus Init done [0002.039] NCK carveout not present [0002.049] Find /i2c@7000c000's alias i2c0 [0002.053] get eeprom at 1-a0, size 256, type 0 [0002.062] Find /i2c@7000c500's alias i2c2 [0002.066] get eeprom at 3-a0, size 256, type 0 [0002.070] get eeprom at 3-ae, size 256, type 0 [0002.075] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.080] I2C slave not started [0002.083] I2C write failed [0002.085] Writing offset failed [0002.089] eeprom_init: EEPROM read failed [0002.092] pm_ids_update: eeprom init failed [0002.097] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.127] pm_ids_update: The pm board id is 3448-0000-200 [0002.134] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50 [0002.142] pm_ids_update: pm id update successful [0002.146] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.177] pm_ids_update: The pm board id is 3449-0000-200 [0002.183] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57 [0002.191] pm_ids_update: pm id update successful [0002.221] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.227] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.235] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.241] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.249] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e5:53:66 [0002.255] Plugin Manager: Parse ODM data 0x000a4000 [0002.268] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.283] Find /i2c@7000c000's alias i2c0 [0002.286] get eeprom at 1-a0, size 256, type 0 [0002.295] Find /i2c@7000c500's alias i2c2 [0002.299] get eeprom at 3-a0, size 256, type 0 [0002.304] get eeprom at 3-ae, size 256, type 0 [0002.308] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.313] I2C slave not started [0002.316] I2C write failed [0002.319] Writing offset failed [0002.322] eeprom_init: EEPROM read failed [0002.326] pm_ids_update: eeprom init failed [0002.330] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.360] pm_ids_update: The pm board id is 3448-0000-200 [0002.366] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50 [0002.373] pm_ids_update: pm id update successful [0002.378] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.408] pm_ids_update: The pm board id is 3449-0000-200 [0002.414] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57 [0002.421] pm_ids_update: pm id update successful [0002.452] Add serial number:1422019049815 as DT property [0002.459] Applying platform configs [0002.466] platform-init is not present. Skipping [0002.470] calling apps_init() [0002.476] Couldn't find GPT header [0002.481] Proceeding to Cold Boot [0002.484] starting app android_boot_app [0002.488] Device state: unlocked [0002.491] display console init [0002.499] could not find regulator [0002.502] hdmi cable connected [0002.506] I2C slave not started [0002.509] I2C write failed [0002.511] Writing offset failed [0002.514] could not read edid [0002.519] tmds-config node not found [0002.523] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micrDT entry for leds-pwm not found o[0002.541] volts [0002.545] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.553] could not find regulator [0002.556] could not find regulator [0002.559] could not find regulator [0002.587] using default cmu settings [0002.591] dc_hdmi_enable, starting HDMI initialisation [0002.597] dc_hdmi_enable, HDMI initialisation complete [0002.602] list and configure display window [0002.607] display console init completed [0002.615] subnode volume_up is not found ! [0002.619] subnode back is not found ! [0002.622] subnode volume_down is not found ! [0002.626] subnode menu is not found ! [0002.630] Gpio keyboard init success [0002.711] found decompressor handler: lz4-legacy [0002.725] decompressing blob (type 1)... [0002.792] load_bmp_blob: panelresolution=480 type=0 [0002.866] decompressor handler not found [0002.870] load_firmware_blob: Firmware blob loaded, entries=2 [0002.876] XUSB blob version 0 size 124416 @ 0x92dee28c [0002.882] -------> se_aes_verify_sbk_clear: 747 [0002.886] se_aes_verify_sbk_clear: Error [0002.890] SE operation failed [0002.893] bl_battery_charging: connected to external power supply [0002.905] device_query_partition_size: failed to open partition spiflash0:MSC ! [0002.912] MSC Partition not found [0002.919] device_query_partition_size: failed to open partition spiflash0:USP ! [0002.926] USP partition read failed! [0002.930] blob_init: blob-partition USP header read failed [0002.935] android_boot Unable to update recovery partition [0002.940] kfs_getpartname: name = LNX [0002.944] Loading kernel from LNX [0002.953] Found 19 BFS partitions in "spiflash0" [0003.276] load kernel from storage [0003.281] decompressor handler not found [0003.549] Successfully loaded kernel and ramdisk images [0003.554] board ID = D78, board SKU = 0 [0003.558] sdmmc node status = okay [0003.562] sdcard instance = 0 [0003.565] sdcard gpio handle 0x5b [0003.568] sdcard gpio pin 0xc9 [0003.571] sdcard gpio flags 0x0 [0003.574] vmmc-supply 0x9e [0003.576] cd_gpio_pin = 201 [0003.579] pin_state = 0 [0003.581] Found sdcard [0003.584] SD-card IS present ... [0003.587] load_and_boot_kernel: SD card detected OK [0003.593] load_bmp_blob: panelresolution=480 type=0 [0003.666] display bmp image done [0003.669] NCK carveout not present [0003.672] Skipping dts_overrides [0003.676] NCK carveout not present [0003.685] Find /i2c@7000c000's alias i2c0 [0003.689] get eeprom at 1-a0, size 256, type 0 [0003.698] Find /i2c@7000c500's alias i2c2 [0003.702] get eeprom at 3-a0, size 256, type 0 [0003.706] get eeprom at 3-ae, size 256, type 0 [0003.711] pm_ids_update: Updating 1,a0, size 256, type 0 [0003.716] I2C slave not started [0003.719] I2C write failed [0003.722] Writing offset failed [0003.725] eeprom_init: EEPROM read failed [0003.729] pm_ids_update: eeprom init failed [0003.733] pm_ids_update: Updating 3,a0, size 256, type 0 [0003.763] pm_ids_update: The pm board id is 3448-0000-200 [0003.770] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50 [0003.778] pm_ids_update: pm id update successful [0003.783] pm_ids_update: Updating 3,ae, size 256, type 0 [0003.813] pm_ids_update: The pm board id is 3449-0000-200 [0003.819] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57 [0003.827] pm_ids_update: pm id update successful [0003.857] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0003.863] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0003.871] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0003.877] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0003.885] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e5:53:66 [0003.892] Plugin Manager: Parse ODM data 0x000a4000 [0003.904] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0003.912] Add serial number:1422019049815 as DT property [0003.921] "bpmp" doesn't exist, creating [0003.927] Updated bpmp info to DTB [0003.932] Updated initrd info to DTB [0003.935] "proc-board" doesn't exist, creating [0003.941] Updated board info to DTB [0003.945] "pmu-board" doesn't exist, creating [0003.951] Updated board info to DTB [0003.954] "display-board" doesn't exist, creating [0003.960] Updated board info to DTB [0003.963] "reset" doesn't exist, creating [0003.968] Updated reset info to DTB [0003.971] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x140000@0x92ca9000 is_hdmi_initialised=1 [0004.011] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0004.016] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0004.029] Updated bootarg info to DTB [0004.033] Adding uuid 0000000164449449080000000dfe8100 to DT [0004.039] Adding eks info 0 to DT [0004.044] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0004.050] Updated memory info to DTB [0004.056] Updated system-lp0-disable info to DTB [0004.064] set vdd_core voltage to 1075 mv [0004.068] setting 'vdd-core' regulator to 1075000 micro volts [0004.074] Found secure-pmc; disable BPMP U-Boot 2020.04-g6b630d64fd (Jan 15 2021 - 14:33:20 -0800) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB OK In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 starting USB... Bus usb@7d000000: tegrausb: Invalid dr_mode 2 for host mode probe failed, error -1 Bus xusb@70090000: Firmware size 124416 Firmware timestamp: 0x5da88fc3, Version: 50.25 release Register HCSParams1: 9000124 NbrPorts: 9 Starting the controller USB XHCI 1.00 scanning bus xusb@70090000 for devices... 4 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Device 0: unknown device switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 839 bytes read in 25 ms (32.2 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 7159844 bytes read in 328 ms (20.8 MiB/s) Retrieving file: /boot/Image 34338824 bytes read in 1501 ms (21.8 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x140000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000083100000, end 000000008317e68d copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.201-tegra (buildbrain@mobile-u64-4415) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Fri Jan 15 14:41:02 PST 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00140000@92ca9000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57560 r8192 d32552 u98304 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x140000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29260(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3567288K/4159488K available (15294K kernel code, 2942K rwdata, 6664K rodata, 8576K init, 609K bss, 117064K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f70000 ( 15296 KB) [ 0.000000] .rodata : 0xffffff8008f70000 - 0xffffff8009600000 ( 6720 KB) [ 0.000000] .init : 0xffffff8009600000 - 0xffffff8009e60000 ( 8576 KB) [ 0.000000] .data : 0xffffff8009e60000 - 0xffffff800a13f808 ( 2943 KB) [ 0.000000] .bss : 0xffffff800a13f808 - 0xffffff800a1d7cbc ( 610 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] PLL_RE already enabled. Postponing set full defaults [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.010009] Console: colour dummy device 80x25 [ 0.014657] console [tty0] enabled [ 0.018165] bootconsole [uart8250] disabled [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.201-tegra (buildbrain@mobile-u64-4415) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Fri Jan 15 14:41:02 PST 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00140000@92ca9000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57560 r8192 d32552 u98304 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 gpt tegra_fbmem=0x140000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29260(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3567288K/4159488K available (15294K kernel code, 2942K rwdata, 6664K rodata, 8576K init, 609K bss, 117064K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f70000 ( 15296 KB) [ 0.000000] .rodata : 0xffffff8008f70000 - 0xffffff8009600000 ( 6720 KB) [ 0.000000] .init : 0xffffff8009600000 - 0xffffff8009e60000 ( 8576 KB) [ 0.000000] .data : 0xffffff8009e60000 - 0xffffff800a13f808 ( 2943 KB) [ 0.000000] .bss : 0xffffff800a13f808 - 0xffffff800a1d7cbc ( 610 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] PLL_RE already enabled. Postponing set full defaults [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.010009] Console: colour dummy device 80x25 [ 0.014657] console [tty0] enabled [ 0.018165] bootconsole [uart8250] disabled [ 0.022496] kmemleak: Kernel memory leak detector disabled [ 0.022525] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.022548] pid_max: default: 32768 minimum: 301 [ 0.023010] Security Framework initialized [ 0.023240] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.023254] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.024388] ftrace: allocating 47208 entries in 185 pages [ 0.193005] ASID allocator initialised with 65536 entries [ 0.232389] tegra-id: chipid=22117. [ 0.232419] tegra-id: opt_subrevision=0. [ 0.232441] Tegra Speedo/IDDQ fuse revision 4 [ 0.232450] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2 [ 0.232498] Tegra: CPU Process ID 0, SoC Process ID 1, GPU Process ID 0 [ 0.232508] Tegra: CPU Speedo Value 2117, SoC Speedo Value 2012, GPU Speedo Value 2122 [ 0.232519] Tegra: CPU IDDQ Value 3008, SoC IDDQ Value 3236, GPU IDDQ Value 4130 [ 0.232545] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 1 [ 0.232566] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-b00.dts [ 0.232586] DTB Build time: Jan 15 2021 14:47:48 [ 0.281310] CPU1: Booted secondary processor [411fd071] [ 0.313215] CPU2: Booted secondary processor [411fd071] [ 0.345180] CPU3: Booted secondary processor [411fd071] [ 0.345281] Brought up 4 CPUs [ 0.345335] SMP: Total of 4 processors activated. [ 0.345352] CPU features: detected feature: 32-bit EL0 Support [ 0.345625] CPU: All CPU(s) started at EL2 [ 0.345652] alternatives: patching kernel code [ 0.353868] devtmpfs: initialized [ 0.392958] Initilizing CustomIPI irq domain [ 0.393439] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.393480] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.404200] pinctrl core: initialized pinctrl subsystem [ 0.404830] OS set in device tree is not L4T. [ 0.405264] regulator-dummy: no parameters [ 0.405589] Initializing plugin-manager [ 0.405756] Plugin module not found [ 0.405953] node /plugin-manager/fragement@0 match with board >=3448-0000-100 [ 0.406477] node /plugin-manager/fragment@1 match with board >=3448-0000-101 [ 0.407200] node /plugin-manager/fragment@5 match with board 3449-0000-200 [ 0.407749] node /plugin-manager/fragement@7 match with odm-data enable-pmic-wdt [ 0.407970] node /plugin-manager/fragement@8 match with odm-data enable-pmic-wdt [ 0.408335] node /plugin-manager/fragement@9 match with board <3448-0000-300 [ 0.413046] NET: Registered protocol family 16 [ 0.414512] pstore: using zlib compression [ 0.415026] console [pstore-1] enabled [ 0.415041] pstore: Registered ramoops as persistent store backend [ 0.415059] ramoops: attached 0x200000@0xb0000000, ecc: 0/0 [ 0.429330] cpuidle: using governor menu [ 0.433677] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver [ 0.435490] vdso: 2 pages (1 code @ ffffff8008f77000, 1 data @ ffffff8009e64000) [ 0.435534] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.437792] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations [ 0.440289] Serial: AMBA PL011 UART driver [ 0.440780] tegra_powergate_init: DONE [ 0.440811] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-b00.dts [ 0.440846] DTB Build time: Jan 15 2021 14:47:48 [ 0.442852] Tegra reboot handler registered. [ 0.447428] iommu: Adding device tegra-carveouts to group 0 [ 0.447601] platform tegra-carveouts: domain=ffffffc0f945a3d8 allocates as[0]=ffffffc0f94480a8 [ 0.447964] iommu: Adding device smmu_test to group 1 [ 0.448029] platform smmu_test: domain=ffffffc0f945a618 allocates as[0]=ffffffc0f9448110 [ 0.448861] mc: mapped MMIO address: 0xffffff800802e000 -> 0x70019000 [ 0.448934] mc: mapped MMIO address: 0xffffff8008065000 -> 0x7001c000 [ 0.449004] mc: mapped MMIO address: 0xffffff8008079000 -> 0x7001d000 [ 0.449026] nv-tegra-mc 70019000.mc: No mssnvlink node [ 0.449057] mc-err: mcerr ops are set to t21x [ 0.459694] iommu: Adding device 70090000.xusb to group 2 [ 0.460009] iommu: Adding device 70006000.serial to group 3 [ 0.460099] platform 70006000.serial: domain=ffffffc0f94d8618 allocates as[0]=ffffffc0f9448178 [ 0.460546] iommu: Adding device 70006040.serial to group 4 [ 0.460835] iommu: Adding device 70006200.serial to group 5 [ 0.461071] iommu: Adding device sound to group 6 [ 0.461133] platform sound: domain=ffffffc0f94d8b58 allocates as[0]=ffffffc0f94481e0 [ 0.461783] iommu: Adding device 7000d400.spi to group 7 [ 0.462057] iommu: Adding device 7000d600.spi to group 8 [ 0.462351] iommu: Adding device 70410000.spi to group 9 [ 0.462675] iommu: Adding device 50000000.host1x to group 10 [ 0.462973] iommu: Adding device 54080000.vi to group 11 [ 0.463377] iommu: Adding device 54600000.isp to group 12 [ 0.463653] iommu: Adding device 54680000.isp to group 13 [ 0.463978] iommu: Adding device tegradc.0 to group 14 [ 0.464049] platform tegradc.0: domain=ffffffc0f94e5a98 allocates as[0]=ffffffc0f9448248 [ 0.465486] platform tegradc.0: IOVA linear map 0x0000000092ca9000(140000) [ 0.465892] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000) [ 0.466234] iommu: Adding device tegradc.1 to group 15 [ 0.466293] platform tegradc.1: domain=ffffffc0f94e5cd8 allocates as[0]=ffffffc0f94482b0 [ 0.467682] platform tegradc.1: IOVA linear map 0x0000000092ca9000(140000) [ 0.468086] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000) [ 0.468341] iommu: Adding device 54340000.vic to group 16 [ 0.468570] iommu: Adding device 544c0000.nvenc to group 17 [ 0.468785] iommu: Adding device 54500000.tsec to group 18 [ 0.469001] iommu: Adding device 54100000.tsecb to group 19 [ 0.469247] iommu: Adding device 54480000.nvdec to group 20 [ 0.469489] iommu: Adding device 54380000.nvjpg to group 21 [ 0.470550] iommu: Adding device 546c0000.i2c to group 22 [ 0.470902] iommu: Adding device 57000000.gpu to group 23 [ 0.470968] platform 57000000.gpu: domain=ffffffc0f94f2cd8 allocates as[0]=ffffffc0f9448318 [ 0.471023] platform 57000000.gpu: domain=ffffffc0f94f2cd8 allocates as[1]=ffffffc0f9448380 [ 0.471078] platform 57000000.gpu: domain=ffffffc0f94f2cd8 allocates as[2]=ffffffc0f94483e8 [ 0.471136] platform 57000000.gpu: domain=ffffffc0f94f2cd8 allocates as[3]=ffffffc0f9448450 [ 0.472043] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.472082] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present [ 0.472110] tegra-pmc: ### PMC reset source: TEGRA_POWER_ON_RESET [ 0.472128] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM [ 0.472144] tegra-pmc: ### PMC reset status reg: 0x0 [ 0.525387] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [ 0.525417] tegra-pmc: Clear bootloader IO dpd settings [ 0.525451] tegra-pmc 7000e400.pmc: IO padctrl driver initialized [ 0.525523] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands [ 0.525832] iommu: Adding device 70012000.se to group 24 [ 0.526635] iommu: Adding device 7000c000.i2c to group 25 [ 0.526902] iommu: Adding device 7000c400.i2c to group 26 [ 0.527172] iommu: Adding device 7000c500.i2c to group 27 [ 0.527438] iommu: Adding device 7000c700.i2c to group 28 [ 0.527734] iommu: Adding device 7000d000.i2c to group 29 [ 0.527998] iommu: Adding device 7000d100.i2c to group 30 [ 0.528300] iommu: Adding device sdhci-tegra.0 to group 31 [ 0.528368] platform sdhci-tegra.0: domain=ffffffc0f9582e58 allocates as[0]=ffffffc0f94484b8 [ 0.529240] iommu: Adding device 700d0000.xudc to group 32 [ 0.532419] vdd-ac-bat: 5000 mV [ 0.532797] vdd-5v0-sys: 5000 mV [ 0.533791] vdd-5v0-hdmi: supplied by vdd-5v0-sys [ 0.533874] vdd-5v0-hdmi: 5000 mV [ 0.534300] vdd-1v8-sys: 1800 mV [ 0.534693] vdd-fan: supplied by vdd-5v0-sys [ 0.534743] vdd-fan: 5000 mV [ 0.535131] vdd-usb-vbus: supplied by vdd-5v0-sys [ 0.535201] vdd-usb-vbus: 5000 mV [ 0.535741] vdd-usb-vbus2: 5000 mV [ 0.566048] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.568551] gpio gpiochip0: gpio-line-names specifies 240 line names but there are 256 lines on the chip [ 0.570344] GPIO line 151 (camera-control-output-low) hogged as output/low [ 0.570387] GPIO line 152 (camera-control-output-low) hogged as output/low [ 0.570805] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio) [ 0.578829] eventlib_kernel: keventlib is initialized, test id: 0 [ 0.579202] SCSI subsystem initialized [ 0.579682] usbcore: registered new interface driver usbfs [ 0.579761] usbcore: registered new interface driver hub [ 0.579849] usbcore: registered new device driver usb [ 0.583895] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.586492] random: fast init done [ 0.589519] vdd-core: 600 <--> 1162 mV at 1075 mV [ 0.590593] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV [ 0.593229] vdd-ddr-1v1: 1150 mV [ 0.597205] vdd-pre-reg-1v35: 1350 mV [ 0.601204] vdd-1v8: 1800 mV [ 0.605232] avdd-sys-1v2: 1200 mV [ 0.609199] vdd-pex-1v0: 1050 mV [ 0.609858] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV [ 0.610449] max77620-ldo3: at 3100 mV [ 0.613205] vdd-rtc: 850 <--> 1100 mV at 1000 mV [ 0.613770] max77620-ldo5: at 3100 mV [ 0.614333] max77620-ldo6: at 2800 mV [ 0.617203] avdd-1v05-pll: 1050 mV [ 0.621198] avdd-io-hdmi-dp: 1050 mV [ 0.623915] GPIO line 505 (spmic-default-output-high) hogged as output/high [ 0.624216] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio) [ 0.624531] max77620 4-003c: max77620 probe successful [ 0.627385] media: Linux media interface: v0.10 [ 0.627463] Linux video capture interface: v2.00 [ 0.628392] pps_core: LinuxPPS API ver. 1 registered [ 0.628413] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.628450] PTP clock support registered [ 0.631642] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table [ 0.632603] Advanced Linux Sound Architecture Driver Initialized. [ 0.633297] Bluetooth: Core ver 2.22 [ 0.633365] NET: Registered protocol family 31 [ 0.633382] Bluetooth: HCI device and connection manager initialized [ 0.633408] Bluetooth: HCI socket layer initialized [ 0.633429] Bluetooth: L2CAP socket layer initialized [ 0.633486] Bluetooth: SCO socket layer initialized [ 0.635299] tegra210_dvfs: no clock found for sdmmc2_ddr [ 0.635336] tegra210_dvfs: no clock found for sdmmc4_ddr [ 0.635394] tegra210_dvfs: no clock found for sdmmc1_ddr [ 0.635421] tegra210_dvfs: no clock found for sdmmc3_ddr [ 0.639054] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe [ 0.640255] vdd-3v3-sys: supplied by vdd-5v0-sys [ 0.640340] vdd-3v3-sys: 3300 mV [ 0.640745] vdd-1v8-sys: supplied by vdd-3v3-sys [ 0.644551] vdd-usb-vbus2: supplied by vdd-3v3-sys [ 0.645030] vdd-3v3-sd: supplied by vdd-3v3-sys [ 0.645115] vdd-3v3-sd: 3300 mV [ 0.646153] avdd-io-edp-1v05: supplied by avdd-1v05-pll [ 0.646209] avdd-io-edp-1v05: 1050 mV [ 0.646703] vdd-usb-hub-en: supplied by vdd-1v8-sys [ 0.646752] vdd-usb-hub-en: 5000 mV [ 0.648124] camchar: rtcpu character device driver loaded [ 0.648924] extcon-gpio-states extcon:extcon@1: Cable state:0, cable id:0 [ 0.650337] clocksource: Switched to clocksource arch_sys_counter [ 0.690871] VFS: Disk quotas dquot_6.6.0 [ 0.691052] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.691555] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.691980] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000 [ 0.692025] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000) [ 0.692270] cma: enabled page replacement for spfn=d7000, epfn=f0000 [ 0.692294] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful [ 0.692322] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout [ 0.692380] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048 [ 0.692405] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout [ 0.692436] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways [ 0.692458] nvmap_page_pool_init: Total RAM pages: 1010606 [ 0.692475] nvmap_page_pool_init: nvmap page pool size: 126325 pages (493 MB) [ 0.692575] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.693072] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB) [ 0.694018] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB) [ 0.702598] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm [ 0.703129] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm [ 0.703534] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm [ 0.703857] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [ 0.704070] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die [ 0.704367] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz [ 0.704387] pre_t19x_iso_plat_init(): max_iso_bw=11520000KB [ 0.704833] NET: Registered protocol family 2 [ 0.705810] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.706049] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.706602] TCP: Hash tables configured (established 32768 bind 32768) [ 0.706774] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.706871] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.707297] NET: Registered protocol family 1 [ 0.708026] RPC: Registered named UNIX socket transport module. [ 0.708051] RPC: Registered udp transport module. [ 0.708067] RPC: Registered tcp transport module. [ 0.708083] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.708338] Trying to unpack rootfs image as initramfs... [ 1.011633] Freeing initrd memory: 6992K [ 1.021493] host1x 50000000.host1x: initialized [ 1.023428] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.026595] audit: initializing netlink subsys (disabled) [ 1.026690] audit: type=2000 audit(0.871:1): initialized [ 1.027477] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 1.037186] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.038841] ntfs: driver 2.1.32 [Flags: R/W]. [ 1.039653] 9p: Installing v9fs 9p2000 file system support [ 1.042911] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240) [ 1.043063] io scheduler noop registered [ 1.043362] io scheduler cfq registered (default) [ 1.046069] gic 702f9000.agic: GIC IRQ controller registered [ 1.049424] iommu: Adding device 702ef000.adsp to group 33 [ 1.058292] iommu: Adding device aconnect@702c0000:adsp_audio to group 34 [ 1.058494] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered [ 1.059108] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x71e8412 [ 1.059139] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4 [ 1.060809] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb [ 1.060949] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb [ 1.061067] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb [ 1.061280] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1 [ 1.061386] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4 [ 1.061493] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4 [ 1.061598] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4 [ 1.061708] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4 [ 1.061823] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb [ 1.061930] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb [ 1.068110] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops [ 1.069827] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000 [ 1.071844] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.073137] tegra-pcie 1003000.pcie: PCIE: Enable power rails [ 1.073481] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.074761] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [ 1.075010] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=750000, max_bw=1500000 [ 1.075272] Adding domain tsec-pd to PM domain host1x-pd [ 1.077549] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 1.078595] tsec 54500000.tsec: initialized [ 1.080253] tsec 54100000.tsecb: initialized [ 1.080969] Adding domain nvdec-pd to PM domain host1x-pd [ 1.084626] nvdec 54480000.nvdec: initialized [ 1.085701] Adding domain vic03-pd to PM domain host1x-pd [ 1.085896] Adding domain msenc-pd to PM domain host1x-pd [ 1.086075] Adding domain nvjpg-pd to PM domain host1x-pd [ 1.090345] falcon 54340000.vic: initialized [ 1.091644] falcon 544c0000.nvenc: initialized [ 1.093003] falcon 54380000.nvjpg: initialized [ 1.097281] tegra_cec 70015000.tegra_cec: dt=1 start=0x70015000 end=0x70015FFF irq=97 [ 1.097353] tegra_cec 70015000.tegra_cec: Enable clock result: 0. [ 1.097408] tegra_cec 70015000.tegra_cec: tegra_cec_init started [ 1.097549] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1 [ 1.097665] display board info: id 0x0, fab 0x0 [ 1.097687] tegra_cec 70015000.tegra_cec: cec_add_sysfs ret=0 [ 1.097706] tegra_cec 70015000.tegra_cec: probed [ 1.097737] generic_infoframe_type: 0x87 [ 1.097897] tegradc tegradc.0: DT parsed successfully [ 1.097963] tegradc tegradc.0: Display dc.ffffff800ab80000 registered with id=0 [ 1.098540] tegradc tegradc.0: Bootloader disp_param detected. Detected mode: 640x480 (on 0x0mm) pclk=25173906 [ 1.102050] tegradc tegradc.0: probed [ 1.107178] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 1.113766] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 22 channels [ 1.114826] tegra-fuse-burn 7000f800.efuse:efuse-burn: shutdown limit check disabled [ 1.114860] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized [ 1.115271] kfuse 7000fc00.kfuse: initialized [ 1.116824] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available [ 1.117785] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0 [ 1.119303] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now [ 1.119350] vdd-cpu: 708 <--> 1322 mV at 708 mV [ 1.119866] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed [ 1.121525] vdd-gpu: applied init 1000000uV constraint [ 1.121557] vdd-gpu: 708 <--> 1323 mV at 997 mV [ 1.121963] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed [ 1.126143] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.126268] No Device Node present for smmu client: serial8250 !! [ 1.126294] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 1.126377] iommu: Adding device serial8250 to group 35 [ 1.128580] Console: switching to colour frame buffer device 80x30 [ 1.128640] tegradc tegradc.0: fb registered [ 1.129399] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 1.129429] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.129444] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 1.129459] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 1.129477] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.131344] console [ttyS0] disabled [ 1.131428] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra [ 1.135329] tegradc tegradc.0: DC initialized, skipping tegra_dc_program_mode. [ 1.135370] tegradc tegradc.0: hdmi: tmds rate:25174K prod-setting:prod_c_hdmi_0m_54m [ 1.135783] tegradc tegradc.0: hdmi: get RGB quant from REG programmed by BL. [ 1.135794] tegradc tegradc.0: hdmi: BL set VIC 0 [ 1.135799] tegradc tegradc.0: hdmi: get YCC quant from REG programmed by BL. [ 1.136479] tegra-i2c 7000c700.i2c: no acknowledge from address 0x50 [ 1.136725] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 1.136729] Extcon AUX1(HDMI) enable [ 1.137570] tegradc tegradc.1: disp1 connected to head1->/host1x/sor [ 1.137639] tegradc tegradc.1: No lt-data, using default setting [ 1.137666] tegradc tegradc.1: No hpd-gpio in DT [ 1.137696] tegradc tegradc.1: DT parsed successfully [ 1.137739] tegradc tegradc.1: Display dc.ffffff800d500000 registered with id=1 [ 1.137979] edid invalid [ 1.139236] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.143479] tegradc tegradc.1: probed [ 1.166576] tegradc tegradc.0: nominal-pclk:25174825 parent:25173906 div:1.0 pclk:25173906 24923052~27440532 [ 1.168887] pci 0000:00:01.0: BAR 14: assigned [mem 0x13000000-0x130fffff] [ 1.168893] pci 0000:00:02.0: BAR 14: assigned [mem 0x13100000-0x131fffff] [ 1.168897] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff] [ 1.168906] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 1.168930] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.168936] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 1.168947] pci 0000:02:00.0: BAR 4: assigned [mem 0x13100000-0x13103fff 64bit] [ 1.168966] pci 0000:02:00.0: BAR 2: assigned [mem 0x13104000-0x13104fff 64bit] [ 1.168984] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 1.168992] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.168996] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 1.169002] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 1.169385] pcieport 0000:00:01.0: Signaling PME through PCIe PME interrupt [ 1.169388] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 1.169709] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt [ 1.169713] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt [ 1.275242] tegradc tegradc.0: hdmi: edid read failed [ 1.275294] tegradc tegradc.0: hdmi: using fallback edid [ 2.106354] tegra_cec 70015000.tegra_cec: physical address: 10:00. [ 3.726859] console [ttyS0] enabled [ 3.726861] tegradc tegradc.1: fb registered [ 3.727692] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART [ 3.727930] serial-tegra 70006200.serial: RX in PIO mode [ 3.728017] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART [ 3.728772] [drm] Initialized [ 3.730216] tegradc tegradc.0: blank - powerdown [ 3.755850] brd: module loaded [ 3.757276] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_evt 1 [ 3.757279] hpd: switching from state 7 (Takeover from bootloader) to state 0 (Reset) [ 3.757316] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0 [ 3.759906] loop: module loaded [ 3.759974] tegra_profiler: version: 1.143, samples/io: 48/28 [ 3.760062] tegra_profiler: auth: init [ 3.760663] THERMAL EST: found 2 subdevs [ 3.760666] THERMAL EST num_resources: 0 [ 3.760674] [THERMAL EST subdev 0] [ 3.760679] [THERMAL EST subdev 1] [ 3.760999] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est [ 3.761001] THERMAL EST: thz register success. [ 3.761107] THERMAL EST: end of probe, return err: 0 [ 3.761809] sd: No Scsi addr parsed to reserve index [ 3.761834] hisi_sas: driver version v1.6 [ 3.765335] tegra-qspi 70410000.spi: Prod settings list not found [ 3.766138] qspi_mtd spi32766.0: MX25U3235F (4096 Kbytes) [ 3.766146] qspi_mtd spi32766.0: mtd .name = spi32766.0, .size = 0x400000 (4MiB) .erasesize = 0x00001000 (4KiB) .numeraseregions = 0 [ 3.768302] libphy: Fixed MDIO Bus: probed [ 3.768919] tun: Universal TUN/TAP device driver, 1.6 [ 3.768921] tun: (C) 1999-2004 Max Krasnyansky [ 3.769528] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 3.769530] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.769578] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 3.769580] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.769622] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 3.769624] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 3.769665] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4 [ 3.769667] Copyright(c) 1999 - 2017 Intel Corporation. [ 3.770314] r8168 0000:02:00.0: enabling device (0000 -> 0003) [ 3.770381] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded [ 3.774020] extcon-disp-state extcon:disp-state: cable 47 state 0 [ 3.774022] Extcon AUX1(HDMI) disable [ 3.795217] r8168 0000:02:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node [ 3.795395] r8168 0000:02:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 00:04:4b:e5:53:66 from device tree [ 3.796070] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [ 3.796127] r8168 Copyright (C) 2017 Realtek NIC software team [ 3.796127] This program comes with ABSOLUTELY NO WARRANTY; for details, please see . [ 3.796127] This is free software, and you are welcome to redistribute it under certain conditions; see . [ 3.796962] PPP generic driver version 2.4.2 [ 3.797209] PPP BSD Compression module registered [ 3.797215] PPP Deflate Compression module registered [ 3.797259] PPP MPPE Compression module registered [ 3.797266] NET: Registered protocol family 24 [ 3.797344] usbcore: registered new interface driver r8152 [ 3.797392] usbcore: registered new interface driver asix [ 3.797469] usbcore: registered new interface driver ax88179_178a [ 3.797511] usbcore: registered new interface driver cdc_ether [ 3.797556] usbcore: registered new interface driver net1080 [ 3.797590] usbcore: registered new interface driver cdc_subset [ 3.797639] usbcore: registered new interface driver zaurus [ 3.797695] usbcore: registered new interface driver cdc_ncm [ 3.797880] VFIO - User Level meta-driver version: 0.3 [ 3.799348] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.799377] ehci-pci: EHCI PCI platform driver [ 3.799433] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.799444] ohci-pci: OHCI PCI platform driver [ 3.799485] ohci-platform: OHCI generic platform driver [ 3.802460] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP [ 3.803066] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0 [ 3.804242] tegra-xusb 70090000.xusb: extcon 0: ffffffc0fa5d2c00 id [ 3.804910] tegradc tegradc.0: unblank [ 3.806393] tegra-xusb 70090000.xusb: Firmware timestamp: 2019-10-17 15:58:59 UTC, Version: 50.25 release [ 3.806469] tegra-xusb 70090000.xusb: xHCI Host Controller [ 3.806497] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1 [ 3.807273] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010 [ 3.807340] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000 [ 3.807543] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.807549] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.807555] usb usb1: Product: xHCI Host Controller [ 3.807558] usb usb1: Manufacturer: Linux 4.9.201-tegra xhci-hcd [ 3.807562] usb usb1: SerialNumber: 70090000.xusb [ 3.808221] hub 1-0:1.0: USB hub found [ 3.808264] hub 1-0:1.0: 5 ports detected [ 3.808894] tegra-xusb 70090000.xusb: xHCI Host Controller [ 3.808907] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2 [ 3.809057] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.809152] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 3.809157] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.809161] usb usb2: Product: xHCI Host Controller [ 3.809166] usb usb2: Manufacturer: Linux 4.9.201-tegra xhci-hcd [ 3.809169] usb usb2: SerialNumber: 70090000.xusb [ 3.809614] hub 2-0:1.0: USB hub found [ 3.809642] hub 2-0:1.0: 4 ports detected [ 3.810249] usbcore: registered new interface driver uas [ 3.810374] usbcore: registered new interface driver usb-storage [ 3.810495] usbcore: registered new interface driver usbserial [ 3.814397] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0 [ 3.814404] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0 [ 3.814763] tegra-xudc-new 700d0000.xudc: device count: 1 [ 3.816367] tegra-xudc-new 700d0000.xudc: USB charger detection disabled [ 3.816380] tegra-xudc-new 700d0000.xudc: vbus state: 0 [ 3.816419] tegra-xudc-new 700d0000.xudc: entering ELPG [ 3.816680] tegra-xudc-new 700d0000.xudc: entering ELPG done [ 3.817390] mousedev: PS/2 mouse device common for all mice [ 3.817499] usbcore: registered new interface driver xpad [ 3.847501] tegradc tegradc.0: nominal-pclk:74250000 parent:74250000 div:1.0 pclk:74250000 73507500~80932500 [ 3.847600] tegradc tegradc.0: hdmi: tmds rate:74250K prod-setting:prod_c_hdmi_54m_75m [ 3.848678] tegradc tegradc.0: hdmi: get YCC quant from EDID. [ 3.852149] tegra_i2c_handle_xfer_error: 10 callbacks suppressed [ 3.852158] tegra-i2c 7000c700.i2c: no acknowledge from address 0x50 [ 3.855379] extcon-disp-state extcon:disp-state: cable 47 state 1 [ 3.855383] Extcon AUX1(HDMI) enable [ 3.865563] tegradc tegradc.0: sync windows ret = 248 [ 3.910441] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1 [ 3.910497] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 2 [ 3.910740] usb usb2: usb_suspend_both: status 0 [ 3.943413] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 3.945622] rtc rtc1: alarm rtc device [ 3.945635] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 3.945662] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 3.946069] i2c /dev entries driver [ 3.947562] imx219 6-0010: tegracam sensor driver:imx219_v2.0.6 [ 3.970832] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10 [ 3.970895] imx219 6-0010: imx219_board_setup: error during i2c read probe (-121) [ 3.970964] imx219 6-0010: board setup failed [ 3.971017] imx219: probe of 6-0010 failed with error -121 [ 3.971859] max77620-power max77620-power: Event recorder REG_NVERC : 0x0 [ 3.973753] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2 [ 3.973757] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4 [ 3.974052] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.974065] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC [ 3.974072] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC [ 3.974200] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.974209] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC [ 3.974215] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC [ 3.974395] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.974404] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC [ 3.974409] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature [ 3.974583] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19 [ 3.975151] tegra_aotag tegra-aotag: Registering sensor 0 [ 3.975199] tegra_aotag tegra-aotag: Invalid temp readout [ 3.975218] tegra_aotag tegra-aotag: Invalid temp readout [ 3.975233] tegra_aotag tegra-aotag: Bound to TZ : ID 0 [ 3.975241] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0 [ 3.975972] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.975986] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered [ 3.976125] tegra_aotag tegra-aotag: Invalid temp readout [ 3.976146] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered [ 3.976471] parse_throttle_dt_data: Num cap clks = 6 [ 3.976474] parse_throttle_dt_data: clk=cclk_g type=2 [ 3.976481] parse_throttle_dt_data: clk=gpu type=4 [ 3.976501] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0 [ 3.976521] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0 [ 3.976543] parse_throttle_dt_data: clk=cap.throttle.sclk type=0 [ 3.976545] parse_throttle_dt_data: clk=emc type=3 [ 3.976895] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.976987] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 3.977093] tegra_throttle_probe: probe successful. #cdevs=4 [ 3.977682] FAN dev name: pwm-fan [ 3.977724] FAN:gpio request success. [ 3.977774] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255 [ 3.978003] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal [ 3.978119] pwm_fan_driver pwm-fan: fan tach request irq success [ 3.978125] pwm_fan_driver pwm-fan: tach period: 1000 [ 3.978202] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2 [ 3.978207] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2 [ 3.978212] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2 [ 3.978216] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2 [ 3.978220] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3 [ 3.978224] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3 [ 3.978227] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3 [ 3.978231] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4 [ 3.978235] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4 [ 3.978239] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4 [ 3.980461] device-mapper: uevent: version 1.0.3 [ 3.980916] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 3.983841] tegra210-cpufreq cpufreq: probe()...completed [ 3.984555] sdhci: Secure Digital Host Controller Interface driver [ 3.984556] sdhci: Copyright(c) Pierre Ossman [ 3.984557] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.985025] sdhci-tegra sdhci-tegra.0: Got CD GPIO [ 3.985375] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful [ 3.985497] sdhci-tegra sdhci-tegra.0: wakeup init done, cdirq 300 [ 3.989452] tegra-se 70012000.se: tegra_se_probe: complete [ 3.989936] hidraw: raw HID events driver (C) Jiri Kosina [ 3.991010] usbcore: registered new interface driver usbhid [ 3.991011] usbhid: USB HID core driver [ 3.993584] tegra21x_actmon 6000c800.actmon: in actmon_register()... [ 3.993764] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all [ 3.995633] nvpmodel: initialized successfully [ 3.996551] usbcore: registered new interface driver snd-usb-audio [ 3.996613] No Device Node present for smmu client: snd-soc-dummy !! [ 3.996618] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 3.996636] iommu: Adding device snd-soc-dummy to group 36 [ 4.009004] OPE platform probe [ 4.009087] OPE platform probe successful [ 4.009113] OPE platform probe [ 4.009193] OPE platform probe successful [ 4.032748] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok [ 4.032879] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok [ 4.032998] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok [ 4.033119] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok [ 4.033246] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok [ 4.033373] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok [ 4.033496] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok [ 4.033618] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok [ 4.033740] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok [ 4.033861] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok [ 4.034504] mmc0: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA 64-bit with 64 bit addr [ 4.045544] u32 classifier [ 4.045546] Actions configured [ 4.045617] Initializing XFRM netlink socket [ 4.046355] NET: Registered protocol family 10 [ 4.047087] NET: Registered protocol family 17 [ 4.047099] NET: Registered protocol family 15 [ 4.047171] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 4.047214] Bluetooth: RFCOMM socket layer initialized [ 4.047223] Bluetooth: RFCOMM ver 1.11 [ 4.047228] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 4.047234] Bluetooth: HIDP socket layer initialized [ 4.047252] 9pnet: Installing 9P2000 support [ 4.047286] Key type dns_resolver registered [ 4.050800] Registered cp15_barrier emulation handler [ 4.057227] Registered setend emulation handler [ 4.058448] registered taskstats version 1 [ 4.059093] Adding domain ve2-pd to PM domain host1x-pd [ 4.059340] Adding domain ve-pd to PM domain host1x-pd [ 4.061399] isp 54600000.isp: initialized [ 4.062348] isp 54680000.isp: initialized [ 4.072577] last reset is due to power on reset [ 4.072580] KERNEL: PMC reset status reg: 0x0 [ 4.072644] BL: PMC reset status reg: 0x0 [ 4.072646] BL: PMIC poweroff Event Recorder: 0x40 [ 4.074194] clk_cbus_recalc_rate: no gbus parent [ 4.074199] clk_cbus_round_rate: no gbus parent [ 4.074200] clk_cbus_round_rate: no gbus parent [ 4.074205] clk_cbus_recalc_rate: no gbus parent [ 4.074309] clk_cbus_recalc_rate: no gbus parent [ 4.074311] clk_cbus_round_rate: no gbus parent [ 4.074313] clk_cbus_round_rate: no gbus parent [ 4.074334] clk_cbus_recalc_rate: no gbus parent [ 4.075034] tegra_dvfs: GPU-cap: registered [ 4.075094] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled [ 4.075096] tegra dvfs: vdd-core: nominal 1075mV, offset 600000uV, step 12500uV, scaling enabled [ 4.075098] tegra dvfs: vdd-gpu: nominal 1038mV, offset 708000uV, step 10000uV, scaling enabled [ 4.076472] tegra_dvfs: vdd-gpu-vts: registered [ 4.077156] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered [ 4.077758] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered [ 4.078233] input: gpio-keys as /devices/gpio-keys/input/input0 [ 4.119471] tegra_rtc 7000e000.rtc: setting system clock to 2000-01-01 01:00:16 UTC (946688416) [ 4.120584] vi 54080000.vi: vi_probe: ++ [ 4.135423] vi 54080000.vi: initialized [ 4.141666] vi 54080000.vi: subdev nvcsi--1 bound [ 4.142744] usb 1-2: new high-speed USB device number 2 using tegra-xusb [ 4.143301] Disable partitions left on by BL [ 4.143303] disb [ 4.143349] bwmgr: missing cdev-type property [ 4.143441] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.143447] DRAM derating cdev registered. [ 4.144323] ALSA device list: [ 4.144326] #1: tegra-snd-t210ref-mobile-rt565x [ 4.186583] usb 1-2: New USB device found, idVendor=0bda, idProduct=5411 [ 4.186587] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.186590] usb 1-2: Product: 4-Port USB 2.1 Hub [ 4.186593] usb 1-2: Manufacturer: Generic [ 4.190151] hub 1-2:1.0: USB hub found [ 4.191259] hub 1-2:1.0: 4 ports detected [ 4.222387] tegra_cec 70015000.tegra_cec: timeout in tegra_cec_native_write_l:172. [ 4.222392] tegra_cec 70015000.tegra_cec: Sent res: -62. [ 4.222395] tegra_cec 70015000.tegra_cec: tegra_cec_init Done. [ 4.235082] mmc0: hw tuning done ... [ 4.235124] mmc0: new ultra high speed SDR104 SDXC card at address aaaa [ 4.235486] mmcblk0: mmc0:aaaa SC64G 59.5 GiB [ 4.241024] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 [ 4.303220] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 4.322355] tegra-xusb-padctl 7009f000.xusb_padctl: power down UTMI pad 1 [ 4.338184] usb 2-1: New USB device found, idVendor=0bda, idProduct=0411 [ 4.338188] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.338191] usb 2-1: Product: 4-Port USB 3.1 Hub [ 4.338193] usb 2-1: Manufacturer: Generic [ 4.342343] usb 1-2: usb_suspend_both: status 0 [ 4.342559] hub 2-1:1.0: USB hub found [ 4.343963] hub 2-1:1.0: 4 ports detected [ 4.458334] usb 1-3: new full-speed USB device number 3 using tegra-xusb [ 4.480042] usb 1-3: New USB device found, idVendor=8087, idProduct=0a2b [ 4.480046] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 4.510339] usb 2-1: usb_suspend_both: status 0 [ 4.510481] usb usb2: usb_suspend_both: status 0 [ 5.898537] tegradc tegradc.1: blank - powerdown [ 5.904375] extcon-disp-state extcon:disp-state: cable 44 state 0 already set. [ 5.904377] Extcon DP: HPD disabled [ 5.904379] hpd: hpd_switch 0 [ 5.904381] hpd: switching from state 0 (Reset) to state 1 (Check Plug) [ 5.904413] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0 [ 5.904418] hpd: switching from state 1 (Check Plug) to state 3 (Disabled) [ 5.924739] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input1 [ 5.958508] extcon-disp-state extcon:disp-state: cable 51 state 1 [ 5.965802] Extcon HDMI: HPD enabled [ 5.965820] tegradc tegradc.0: hdmi: plugged [ 5.979086] Freeing unused kernel memory: 8576K [ 6.009106] Root device found: mmcblk0p1 [ 6.015873] Found dev node: /dev/mmcblk0p1 [ 6.075138] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 6.086448] Rootfs mounted over mmcblk0p1 [ 6.121406] Switching from initrd to actual rootfs [ 6.309016] systemd[1]: System time before build time, advancing clock. [ 6.342675] ip_tables: (C) 2000-2006 Netfilter Core Team [ 6.363143] cgroup: cgroup2: unknown option "nsdelegate" [ 6.392264] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [ 6.417044] systemd[1]: Detected architecture arm64. [ 6.455473] systemd[1]: Set hostname to . [ 6.569808] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 6.589689] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 6.735418] random: systemd: uninitialized urandom read (16 bytes read) [ 6.745177] systemd[1]: Created slice System Slice. [ 6.753381] random: systemd: uninitialized urandom read (16 bytes read) [ 6.761619] systemd[1]: Listening on udev Kernel Socket. [ 6.770063] random: systemd: uninitialized urandom read (16 bytes read) [ 6.778370] systemd[1]: Listening on Syslog Socket. [ 6.786564] systemd[1]: Listening on fsck to fsckd communication Socket. [ 6.796608] systemd[1]: Listening on Journal Socket (/dev/log). [ 6.905839] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null) [ 7.018171] nvgpu: 57000000.gpu gm20b_init_clk_setup_sw:1268 [INFO] GPCPLL initial settings: NA mode, M=1, N=34, P=3 (id = 1) [ 7.039318] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 7.050604] cpu-throttle-alert cooling device registered. [ 7.065587] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 7.076587] gpu-throttle-alert cooling device registered. [ 7.083718] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 7.094391] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 7.103104] systemd-journald[2025]: Received request to flush runtime journal from PID 1 [ 7.114572] hot-surface-alert cooling device registered. [ 8.233471] random: crng init done [ 8.237823] random: 7 urandom warning(s) missed due to ratelimiting [ 8.607057] using random self ethernet address [ 8.612626] using random host ethernet address [ 9.187255] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-26.ucode failed with error -2 [ 9.200543] iwlwifi 0000:01:00.0: Falling back to user helper [ 9.284382] using random self ethernet address [ 9.289974] using random host ethernet address [ 10.538591] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-25.ucode failed with error -2 [ 10.538594] iwlwifi 0000:01:00.0: Falling back to user helper [ 10.904007] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-24.ucode failed with error -2 [ 10.915689] iwlwifi 0000:01:00.0: Falling back to user helper [ 10.931254] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-23.ucode failed with error -2 [ 10.942791] iwlwifi 0000:01:00.0: Falling back to user helper [ 11.177032] thermal thermal_zone6: failed to read out thermal zone (-5) Ubuntu 18.04.5 LTS vkrobot-desktop ttyS0 vkrobot-desktop login: