Welcome to minicom 2.7 OPTIONS: I18n Compiled on Nov 15 2018, 20:18:47. Port /dev/ttyUSB0, 19:37:20 Press CTRL-A Z for help on special keys [0000.233] [L4T TegraBoot] (version 00.00.2018.01-l4t-80a468da) [0000.239] Processing in cold boot mode Bootloader 2 [0000.243] A02 Bootrom Patch rev = 1023 [0000.247] Power-up reason: pmc por [0000.250] No Battery Present [0000.253] pmic max77620 reset reason [0000.256] pmic max77620 NVERC : 0xf6 [0000.259] RamCode = 0 [0000.262] Platform has DDR4 type RAM [0000.265] max77620 disabling SD1 Remote Sense [0000.269] Setting DDR voltage to 1125mv [0000.273] Serial Number of Pmic Max77663: 0x2404b9 [0000.281] Entering ramdump check [0000.284] Get RamDumpCarveOut = 0x0 [0000.287] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.292] Last reboot was clean, booting normally! [0000.297] Sdram initialization is successful [0000.301] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.307] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.313] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.319] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.325] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.331] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.336] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.342] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.358] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.364] Platform-DebugCarveout: 0 [0000.368] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.373] Non secure mode, and RB not enabled. [0000.390] Csd NumOfBlocks=0 [0000.582] *** Booting BFS0. [0000.585] Read PT from (0:3) [0000.591] Using BFS PT to query partitions [0000.595] PT: Partition LNX NOT found ! [0001.189] *** Booting KFS0. [0001.192] Read GPT from (0:3) [0001.196] Using GPT Primary to query partitions [0001.200] Loading Tboot-CPU binary [0001.208] Verifying TBC in OdmNonSecureSBK mode [0001.218] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0001.225] Bootloader downloaded successfully. [0001.229] Downloaded Tboot-CPU binary to 0xa0000258 [0001.234] MAX77620_GPIO5 configured [0001.237] CPU power rail is up [0001.240] CPU clock enabled [0001.244] Performing RAM repair [0001.247] Updating A64 Warmreset Address to 0xa00002e9 [0001.252] Loading NvTbootBootloaderDTB [0001.269] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0001.334] Bootloader DTB Load Address: 0x83000000 [0001.339] Loading NvTbootKernelDTB [0001.356] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0001.421] Kernel DTB Load Address: 0x83100000 [0001.426] Loading cboot binary [0001.437] Verifying EBT in OdmNonSecureSBK mode [0001.479] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0001.486] Bootloader downloaded successfully. [0001.490] PT: Partition NCT NOT found ! [0001.494] Warning: Find Partition via PT Failed [0001.498] Next binary entry address: 0x92c00258 [0001.503] BoardId: 3448 [0001.507] Overriding pmu board id with proc board id [0001.512] Display board id is not available [0001.524] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.576] /bpmp deleted [0001.578] SC7EntryFw header found loaded at 0xff700000 [0001.768] OVR2 PMIC [0001.770] Bpmp FW successfully loaded [0001.775] WB0 init successfully at 0xff780000 [0001.779] Set NvDecSticky Bits [0001.783] GSC2 address ff53fffc value c0edbbcc [0001.789] GSC MC Settings done [0001.792] TOS Image length 53680 [0001.795] Monitor size 53680 [0001.798] OS size 0 [0001.803] Secure Os AES-CMAC Verification Success! [0001.808] TOS image cipher info: plaintext [0001.812] Loading and Validation of Secure OS Successful [0001.828] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.832] NvTbootPackSdramParams: start. [0001.837] NvTbootPackSdramParams: done. [0001.841] Tegraboot started after 163111 us [0001.845] Basic modules init took 1390451 us [0001.849] Sec Bootdevice Read Time = 553 ms, Read Size = 14459 KB [0001.855] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.861] Next stage binary read took 7390 us [0001.865] Carveout took -19292 us [0001.868] CPU initialization took 343981 us [0001.872] Total time taken by TegraBoot 1722530 us [0001.877] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):41d46a9cf NOTICE: BL31: Built : 21:18:12, Jun 25 2020 ERROR: Error initializing runtime service trusty_fast [0001.999] RamCode = 0 [0002.004] LPDDR4 Training: Read DT: Number of tables = 2 [0002.009] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0002.021] EMC Training Successful [0002.024] 408000 not found in DVFS table [0002.031] RamCode = 0 [0002.034] DT Write: emc-table@204000 succeeded [0002.040] DT Write: emc-table@1600000 succeeded [0002.044] LPDDR4 Training: Write DT: Number of tables = 2 [0002.102] [0002.103] Debug Init done [0002.105] Marked DTB cacheable [0002.108] Bootloader DTB loaded at 0x83000000 [0002.113] Marked DTB cacheable [0002.116] Kernel DTB loaded at 0x83100000 [0002.120] DeviceTree Init done [0002.133] Pinmux applied successfully [0002.137] gicd_base: 0x50041000 [0002.141] gicc_base: 0x50042000 [0002.144] Interrupts Init done [0002.148] Using base:0x60005090 & irq:208 for tick-timer [0002.153] Using base:0x60005098 for delay-timer [0002.158] platform_init_timer: DONE [0002.161] Timer(tick) Init done [0002.165] osc freq = 38400 khz [0002.169] [0002.170] Welcome to L4T Cboot [0002.173] [0002.174] Cboot Version: 00.00.2018.01-t210-3a7ad565 [0002.179] calling constructors [0002.182] initializing heap [0002.185] initializing threads [0002.188] initializing timers [0002.190] creating bootstrap completion thread [0002.195] top of bootstrap2() [0002.198] CPU: ARM Cortex A57 [0002.201] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0002.205] initializing platform [0002.259] Config for emmc ddr50 mode completed [0002.263] sdmmc bdev is already initialized [0002.268] Enable APE clock [0002.270] Un-powergate APE partition [0002.274] of_register: registering tegra_udc to of_hal [0002.279] of_register: registering inv20628-driver to of_hal [0002.284] of_register: registering ads1015-driver to of_hal [0002.290] of_register: registering lp8557-bl-driver to of_hal [0002.296] of_register: registering bq2419x_charger to of_hal [0002.301] of_register: registering bq27441_fuel_gauge to of_hal [0002.313] gpio framework initialized [0002.316] of_register: registering tca9539_gpio to of_hal [0002.322] of_register: registering tca9539_gpio to of_hal [0002.327] of_register: registering i2c_bus_driver to of_hal [0002.333] of_register: registering i2c_bus_driver to of_hal [0002.338] of_register: registering i2c_bus_driver to of_hal [0002.344] pmic framework initialized [0002.347] of_register: registering max77620_pmic to of_hal [0002.353] regulator framework initialized [0002.357] of_register: registering tps65132_bl_driver to of_hal [0002.363] initializing target [0002.368] gpio_driver_register: register 'tegra_gpio_driver' driver [0002.379] fixed regulator driver initialized [0002.397] initializing OF layer [0002.400] NCK carveout not present [0002.403] Skipping dts_overrides [0002.407] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.424] I2C Bus Init done [0002.426] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.437] I2C Bus Init done [0002.439] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.450] I2C Bus Init done [0002.452] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.463] I2C Bus Init done [0002.465] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.476] I2C Bus Init done [0002.478] of_children_init: Ops found for compatible string maxim,max77620 [0002.489] max77620_init using irq 118 [0002.494] register 'maxim,max77620' pmic [0002.498] gpio_driver_register: register 'max77620-gpio' driver [0002.504] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.515] I2C Bus Init done [0002.518] NCK carveout not present [0002.528] Find /i2c@7000c000's alias i2c0 [0002.532] get eeprom at 1-a0, size 256, type 0 [0002.541] Find /i2c@7000c500's alias i2c2 [0002.545] get eeprom at 3-a0, size 256, type 0 [0002.549] get eeprom at 3-ae, size 256, type 0 [0002.554] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.559] I2C slave not started [0002.562] I2C write failed [0002.565] Writing offset failed [0002.568] eeprom_init: EEPROM read failed [0002.572] pm_ids_update: eeprom init failed [0002.576] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.606] pm_ids_update: The pm board id is 3448-0002-400 [0002.613] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0002.620] pm_ids_update: pm id update successful [0002.625] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.655] pm_ids_update: The pm board id is 3449-0000-400 [0002.662] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.670] pm_ids_update: pm id update successful [0002.700] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.706] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.714] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.720] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.729] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e9:fb:4c [0002.735] Plugin Manager: Parse ODM data 0x00094000 [0002.745] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x7 [0002.760] Find /i2c@7000c000's alias i2c0 [0002.764] get eeprom at 1-a0, size 256, type 0 [0002.773] Find /i2c@7000c500's alias i2c2 [0002.777] get eeprom at 3-a0, size 256, type 0 [0002.781] get eeprom at 3-ae, size 256, type 0 [0002.785] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.791] I2C slave not started [0002.794] I2C write failed [0002.796] Writing offset failed [0002.799] eeprom_init: EEPROM read failed [0002.803] pm_ids_update: eeprom init failed [0002.807] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.838] pm_ids_update: The pm board id is 3448-0002-400 [0002.844] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0002.851] pm_ids_update: pm id update successful [0002.856] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.886] pm_ids_update: The pm board id is 3449-0000-400 [0002.892] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.899] pm_ids_update: pm id update successful [0002.930] Add serial number:1423219121389 as DT property [0002.938] Applying platform configs [0002.944] platform-init is not present. Skipping [0002.949] calling apps_init() [0002.965] Found 17 GPT partitions in "sdmmc3_user" [0002.969] Proceeding to Cold Boot [0002.973] starting app android_boot_app [0002.976] Device state: unlocked [0002.979] display console init [0002.988] could not find regulator [0002.991] hdmi cable connected [0003.007] edid read success [0003.024] DT entry for leds-pwm not found [0003.028] edid read success [0003.030] width = 640, height = 480, frequency = 25174825 [0003.036] width = 2560, height = 1440, frequency = 241500000 [0003.041] width = 1920, height = 1080, frequency = 148500000 [0003.047] width = 1920, height = 1080, frequency = 148351648 [0003.053] width = 1920, height = 1080, frequency = 148351648 [0003.058] width = 1280, height = 720, frequency = 74175824 [0003.064] width = 1280, height = 720, frequency = 74175824 [0003.069] width = 720, height = 480, frequency = 26973026 [0003.075] width = 720, height = 576, frequency = 26973026 [0003.080] width = 720, height = 480, frequency = 26973026 [0003.085] width = 720, height = 576, frequency = 26973026 [0003.091] width = 640, height = 480, frequency = 25174825 [0003.096] Best mode Width = 1920, Height = 1080, freq = 148351648 [0003.104] tmds-config node not found [0003.108] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltageps [0003.123] setting 'vdd-1v8' regulator to 1800000 micro volts [0003.130] could not find regulator [0003.134] could not find regulator [0003.137] could not find regulator [0003.165] using default cmu settings [0003.169] dc_hdmi_enable, starting HDMI initialisation [0003.175] dc_hdmi_enable, HDMI initialisation complete [0003.180] list and configure display window [0003.189] display console init completed [0003.200] subnode volume_up is not found ! [0003.204] subnode back is not found ! [0003.207] subnode volume_down is not found ! [0003.212] subnode menu is not found ! [0003.215] Gpio keyboard init success [0003.262] found decompressor handler: lz4-legacy [0003.277] decompressing blob (type 1)... [0003.312] load_bmp_blob: panelresolution=1080 type=3 [0003.362] decompressor handler not found [0003.366] load_firmware_blob: Firmware blob loaded, entries=2 [0003.371] -------> se_aes_verify_sbk_clear: 747 [0003.376] se_aes_verify_sbk_clear: Error [0003.380] bl_battery_charging: connected to external power supply [0003.387] xusb is supported [0003.393] error while finding nvidia,portmap [0003.897] xusb blob version 0 size 124416 [0003.901] firmware size 124416 [0003.906] Firmware timestamp: 0x5da88fc3, Version: 50.25 release [0003.920] xhci0: 64 bytes context size, 32-bit DMA [0003.960] usbus0: 5.0Gbps Super Speed USB v3.0 [0003.981] uhub0: on u0 [0004.630] uhub0: 9 ports with 9 removable, self powered [0005.630] failed to get HID devices [0005.634] failed to init xhci or no usb device attached [0005.648] device_query_partition_size: failed to open partition sdmmc3_user:MS! [0005.655] MSC Partition not found [0005.665] device_query_partition_size: failed to open partition sdmmc3_user:US! [0005.672] USP partition read failed! [0005.676] blob_init: blob-partition USP header read failed [0005.681] android_boot Unable to update recovery partition [0005.687] kfs_getpartname: name = LNX [0005.690] Loading kernel from LNX [0005.754] load kernel from storage [0005.764] decompressor handler not found [0005.783] Successfully loaded kernel and ramdisk images [0005.790] load_bmp_blob: panelresolution=1080 type=3 [0006.284] display bmp image done [0006.287] NCK carveout not present [0006.290] Skipping dts_overrides [0006.293] NCK carveout not present [0006.303] Find /i2c@7000c000's alias i2c0 [0006.307] get eeprom at 1-a0, size 256, type 0 [0006.316] Find /i2c@7000c500's alias i2c2 [0006.320] get eeprom at 3-a0, size 256, type 0 [0006.324] get eeprom at 3-ae, size 256, type 0 [0006.329] pm_ids_update: Updating 1,a0, size 256, type 0 [0006.334] I2C slave not started [0006.337] I2C write failed [0006.340] Writing offset failed [0006.343] eeprom_init: EEPROM read failed [0006.347] pm_ids_update: eeprom init failed [0006.351] pm_ids_update: Updating 3,a0, size 256, type 0 [0006.381] pm_ids_update: The pm board id is 3448-0002-400 [0006.388] Adding plugin-manager/ids/3448-0002-400=/i2c@7000c500:module@0x50 [0006.395] pm_ids_update: pm id update successful [0006.400] pm_ids_update: Updating 3,ae, size 256, type 0 [0006.430] pm_ids_update: The pm board id is 3449-0000-400 [0006.436] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0006.444] pm_ids_update: pm id update successful [0006.475] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0006.481] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0006.489] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0006.495] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0006.504] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e9:fb:4c [0006.510] Plugin Manager: Parse ODM data 0x00094000 [0006.520] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x7 [0006.528] Add serial number:1423219121389 as DT property [0006.537] "bpmp" doesn't exist, creating [0006.543] Updated bpmp info to DTB [0006.548] Updated initrd info to DTB [0006.551] "proc-board" doesn't exist, creating [0006.557] Updated board info to DTB [0006.560] "pmu-board" doesn't exist, creating [0006.565] Updated board info to DTB [0006.569] "display-board" doesn't exist, creating [0006.574] Updated board info to DTB [0006.578] "reset" doesn't exist, creating [0006.582] Updated reset info to DTB [0006.586] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype [0006.625] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0006.630] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 [0006.646] Updated bootarg info to DTB [0006.650] Adding uuid 0000000164456806240000000c0084c0 to DT [0006.656] Adding eks info 0 to DT [0006.661] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0006.667] Updated memory info to DTB [0006.676] set vdd_core voltage to 1125 mv [0006.680] setting 'vdd-core' regulator to 1125000 micro volts [0006.701] Found secure-pmc; disable BPMP U-Boot 2016.07-ge6da093be3 (Jun 25 2020 - 21:18:08 -0700) TEGRA210 Model: NVIDIA P3450-Porg Board: NVIDIA P3450-PORG DRAM: 4 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 SF: Failed to get idcodes *** Warning - spi_flash_probe() failed, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Card did not respond to voltage select! ** Bad device mmc 1 ** Hit any key to stop autoboot: 0 Card did not respond to voltage select! switch to partitions #0, OK mmc0(part 0) is current device Failed to mount ext2 filesystem... ** Unrecognized filesystem type ** starting USB... USB0: tegrausb: Invalid dr_mode 2 for host mode probe failed, error -1 USB error: all controllers failed lowlevel init PCI device eth_rtl8169: unknown chip version, assuming RTL-8169 PCI device: TxConfig = 0x4B100D00 BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 192.168.0.20 (828 ms) *** Warning: no boot file name; using 'C0A80014.img' Using eth_rtl8169 device TFTP from server 192.168.0.1; our IP address is 192.168.0.20 Filename 'C0A80014.img'. Load address: 0x83280000