[BEGIN] 2022/6/28 11:29:14 t-desktop login: [ 182.856004] tegra-i2c 3190000.i2c: arb lost in communicate to add 0x50 [ 182.856143] tegra-i2c 3190000.i2c: Un-recovered Arb lost [ 185.889135] watchdog: watchdog0: watchdog did not stop! [ 185.901211] systemd-shutdow: 33 output lines suppressed due to ratelimiting [ 186.171428] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 186.276314] ata1.00: disabled [ 186.280506] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 186.343750] reboot: Restarting system [0000.163] I> Welcome to MB2(TBoot-BPMP)(version: 01.00.160913-t186-M-00.00-mobile-c368a720) [0000.172] I> Boot-device: eMMC [0000.179] I> sdmmc bdev is already initialized [0000.184] I> pmic: reset reason (nverc) : 0x0 [0000.217] I> Found 19 partitions in SDMMC_BOOT (instance 3) [0000.236] I> Found 33 partitions in SDMMC_USER (instance 3) [0000.242] W> No valid slot number is found in scratch register [0000.248] W> Return default slot: _a [0000.251] I> A/B: bin_type (16) slot 0 [0000.255] I> Loading partition bpmp-fw at 0xd7800000 [0000.260] I> Reading two headers - addr:0xd7800000 blocks:1 [0000.265] I> Addr: 0xd7800000, start-block: 58777608, num_blocks: 1 [0000.291] I> Binary(16) of size 534416 is loaded @ 0xd7800000 [0000.296] W> No valid slot number is found in scratch register [0000.302] W> Return default slot: _a [0000.305] I> A/B: bin_type (17) slot 0 [0000.309] I> Loading partition bpmp-fw-dtb at 0xd79f0000 [0000.314] I> Reading two headers - addr:0xd79f0000 blocks:1 [0000.320] I> Addr: 0xd79f0000, start-block: 58780024, num_blocks: 1 [0000.345] I> Binary(17) of size 604720 is loaded @ 0xd796c400 [0000.575] I> Loading SCE-FW ... [0000.578] W> No valid slot number is found in scratch register [0000.584] W> Return default slot: _a [0000.587] I> A/B: bin_type (12) slot 0 [0000.591] I> Loading partition sce-fw at 0xd7300000 [0000.596] I> Reading two headers - addr:0xd7300000 blocks:1 [0000.601] I> Addr: 0xd7300000, start-block: 58784120, num_blocks: 1 [0000.620] I> Binary(12) of size 125632 is loaded @ 0xd7300000 [0000.626] I> Init SCE [0000.628] I> Loading APE-FW ... [0000.631] W> No valid slot number is found in scratch register [0000.637] W> Return default slot: _a [0000.641] I> A/B: bin_type (11) slot 0 [0000.644] I> Loading partition adsp-fw at 0xd7400000 [0000.649] I> Reading two headers - addr:0xd7400000 blocks:1 [0000.654] I> Addr: 0xd7400000, start-block: 58761224, num_blocks: 1 [0000.673] I> Binary(11) of size 77216 is loaded @ 0xd7400000 [0000.679] I> Copy BTCM section [0000.682] W> No valid slot number is found in scratch register [0000.688] W> Return default slot: _a [0000.691] I> A/B: bin_type (13) slot 0 [0000.695] I> Loading partition cpu-bootloader at 0x96000000 [0000.700] I> Reading two headers - addr:0x96000000 blocks:1 [0000.706] I> Addr: 0x96000000, start-block: 58740744, num_blocks: 1 [0000.727] I> Binary(13) of size 308800 is loaded @ 0x96000000 [0000.733] W> No valid slot number is found in scratch register [0000.739] W> Return default slot: _a [0000.742] I> A/B: bin_type (20) slot 0 [0000.746] I> Loading partition bootloader-dtb at 0x85205400 [0000.751] I> Reading two headers - addr:0x85205400 blocks:1 [0000.756] I> Addr: 0x85205400, start-block: 58742792, num_blocks: 1 [0000.778] I> Binary(20) of size 374192 is loaded @ 0x85205400 [0000.784] W> No valid slot number is found in scratch register [0000.790] W> Return default slot: _a [0000.793] I> A/B: bin_type (14) slot 0 [0000.797] I> Loading partition secure-os at 0x85305600 [0000.802] I> Reading two headers - addr:0x85305600 blocks:1 [0000.807] I> Addr: 0x85305600, start-block: 58744840, num_blocks: 1 [0000.829] I> Binary(14) of size 402864 is loaded @ 0x85305600 [0000.837] I> TOS boot-params @ 0x85000000 [0000.841] I> TOS params prepared [0000.844] I> Loading EKS ... [0000.847] I> A/B: bin_type (15) slot 0 [0000.850] I> Loading partition eks at 0x85905800 [0000.855] I> Reading two headers - addr:0x85905800 blocks:1 [0000.860] I> Addr: 0x85905800, start-block: 58757128, num_blocks: 1 [0000.879] I> Binary(15) of size 1040 is loaded @ 0x85905800 [0000.885] I> EKB detected (length: 0x400) @ 0x85905800 [0000.890] I> Copied encrypted keys [0000.893] I> boot profiler @ 0x275844000 [0000.897] I> boot profiler for TOS @ 0x275844000 [0000.902] I> Unhalting SCE [0000.905] I> Primary Memory Start:80000000 Size:70000000 [0000.910] I> Extended Memory Start:f0110000 Size:1856f0000 [0000.917] I> MB2(TBoot-BPMP) done NOTICE: BL31: v1.3(release):b5eeb33f7 NOTICE: BL31: Built : 12:15:17, Jul 26 2021 ipc-unittest-main: 1519: Welcome to IPC unittest!!! ipc-unittest-main: 1531: waiting forever ipc-unittest-srv: 329: Init unittest services!!! hwkey-agent: 41: hwkey-agent is running!! hwkey-agent: 315: key_mgnt_processing ....... hwkey-agent: 223: Setting EKB key 0 to slot 14 hwkey-agent: 178: Init hweky-agent services!! luks-srv: 40: luks-srv is running!! luks-srv: 157: Init luks-srv IPC services!! platform_bootstrap_epilog: trusty bootstrap complete [0001.289] I> Welcome to Cboot [0001.292] I> Cboot Version: t186-00029e71 [0001.296] I> CPU-BL Params @ 0x275800000 [0001.300] I> 0) Base:0x00000000 Size:0x00000000 [0001.304] I> 1) Base:0x277f00000 Size:0x00100000 [0001.309] I> 2) Base:0x277e00000 Size:0x00100000 [0001.313] I> 3) Base:0x277d00000 Size:0x00100000 [0001.318] I> 4) Base:0x277c00000 Size:0x00100000 [0001.322] I> 5) Base:0x277b00000 Size:0x00100000 [0001.327] I> 6) Base:0x277800000 Size:0x00200000 [0001.331] I> 7) Base:0x277400000 Size:0x00400000 [0001.336] I> 8) Base:0x277a00000 Size:0x00100000 [0001.340] I> 9) Base:0x277300000 Size:0x00100000 [0001.345] I> 10) Base:0x276800000 Size:0x00800000 [0001.349] I> 11) Base:0x30000000 Size:0x00040000 [0001.354] I> 12) Base:0xf0000000 Size:0x00100000 [0001.358] I> 13) Base:0x30040000 Size:0x00001000 [0001.362] I> 14) Base:0x30048000 Size:0x00001000 [0001.367] I> 15) Base:0x30049000 Size:0x00001000 [0001.371] I> 16) Base:0x3004a000 Size:0x00001000 [0001.376] I> 17) Base:0x3004b000 Size:0x00001000 [0001.380] I> 18) Base:0x3004c000 Size:0x00001000 [0001.385] I> 19) Base:0x3004d000 Size:0x00001000 [0001.389] I> 20) Base:0x3004e000 Size:0x00001000 [0001.394] I> 21) Base:0x3004f000 Size:0x00001000 [0001.398] I> 22) Base:0x00000000 Size:0x00000000 [0001.402] I> 23) Base:0xf0100000 Size:0x00010000 [0001.407] I> 24) Base:0x00000000 Size:0x00000000 [0001.411] I> 25) Base:0x00000000 Size:0x00000000 [0001.416] I> 26) Base:0x00000000 Size:0x00000000 [0001.420] I> 27) Base:0x00000000 Size:0x00000000 [0001.425] I> 28) Base:0x84400000 Size:0x00400000 [0001.429] I> 29) Base:0x30000000 Size:0x00010000 [0001.433] I> 30) Base:0x278000000 Size:0x08000000 [0001.438] I> 31) Base:0x00000000 Size:0x00000000 [0001.442] I> 32) Base:0x276000000 Size:0x00600000 [0001.447] I> 33) Base:0x80000000 Size:0x70000000 [0001.451] I> 34) Base:0xf0110000 Size:0x1856f0000 [0001.456] I> 35) Base:0x00000000 Size:0x00000000 [0001.460] I> 36) Base:0x00000000 Size:0x00000000 [0001.465] I> 37) Base:0x2772e0000 Size:0x00020000 [0001.469] I> 38) Base:0x84000000 Size:0x00400000 [0001.474] I> 39) Base:0x96000000 Size:0x02000000 [0001.478] I> 40) Base:0x85000000 Size:0x01200000 [0001.482] I> 41) Base:0x275800000 Size:0x00500000 [0001.487] I> 42) Base:0x00000000 Size:0x00000000 [0001.491] I> 43) Base:0x00000000 Size:0x00000000 [0001.496] GIC-SPI Target CPU: 4 [0001.499] Interrupts Init done [0001.502] calling constructors [0001.506] initializing heap [0001.508] initializing threads [0001.511] initializing timers [0001.515] creating bootstrap completion thread [0001.519] top of bootstrap2() [0001.522] CPU: ARM Cortex A57 [0001.525] CPU: MIDR: 0x411FD073, MPIDR: 0x80000100 [0001.531] initializing platform [0001.534] I> Bl_dtb @0x85205400 [0001.537] I> gpio framework initialized [0001.543] I> tegrabl_gpio_driver_register: register 'nvidia,tegra186-gpio' driver [0001.553] I> tegrabl_gpio_driver_register: register 'nvidia,tegra186-gpio-aon' driver [0001.561] I> GPIO framework and drivers are initialized. [0001.566] I> Boot-device: eMMC [0001.573] I> sdmmc bdev is already initialized [0001.604] I> Found 19 partitions in SDMMC_BOOT (instance 3) [0001.622] I> Found 33 partitions in SDMMC_USER (instance 3) [0001.627] W> opt-in fuse is not set, skip fuse_burning [0001.632] I> Reserved memory at 0xfbe00000 for U-Boot relocation [0001.638] W> No valid slot number is found in scratch register [0001.644] W> Return default slot: _a [0001.653] I> A/B: bin_type (21) slot 0 [0001.657] I> Loading kernel-dtb from partition [0001.661] I> Loading partition kernel-dtb at 0x80000000 from device(0x1) [0001.679] I> Kernel_dtb @0x80000000 [0001.682] I> tegrabl_tca9539_init: i2c bus: 0, slave addr: 0xee [0001.690] E> I2C: slave not found in slaves. [0001.694] E> I2C: Could not write 0 bytes to slave: 0x00ee with repeat start false. [0001.702] E> I2C_DEV: Failed to send register address 0x00000004. [0001.708] E> I2C_DEV: Could not write 1 registers of size 1 to slave 0xee at 0x00000004 via instance 0. [0001.717] E> tca9539_device_init: failed to write polar reg [0001.723] E> tegrabl_tca9539_init: failed to init device! [0001.728] I> tegrabl_tca9539_init: i2c bus: 0, slave addr: 0xe8 [0001.735] E> I2C: slave not found in slaves. [0001.739] E> I2C: Could not write 0 bytes to slave: 0x00e8 with repeat start false. [0001.747] E> I2C_DEV: Failed to send register address 0x00000004. [0001.752] E> I2C_DEV: Could not write 1 registers of size 1 to slave 0xe8 at 0x00000004 via instance 0. [0001.762] E> tca9539_device_init: failed to write polar reg [0001.767] E> tegrabl_tca9539_init: failed to init device! [0001.775] I> fixed regulator driver initialized [0001.809] I> register 'maxim' power off handle [0001.815] I> virtual i2c enabled [0001.818] I> registered 'maxim,max77620' pmic [0001.822] I> tegrabl_gpio_driver_register: register 'max77620-gpio' driver [0001.836] E> failed to read label property for node 323560: 13 [0001.844] E> failed to read reg property for node 323656: 13 [0001.853] E> failed to read reg property for node 323708: 13 [0001.861] E> failed to read label property for node 323792: 13 [0001.869] E> failed to read label property for node 323860: 13 [0001.878] E> failed to read reg property for node 323928: 13 [0001.886] E> failed to read reg property for node 324000: 13 [0001.896] I> Find /i2c@c250000's alias i2c7 [0001.900] I> Reading eeprom i2c=7 address=0x50 [0001.930] I> Device at /i2c@c250000:0x50 [0001.933] I> Reading eeprom i2c=7 address=0x57 [0001.938] E> I2C: slave not found in slaves. [0001.942] E> I2C: Could not write 0 bytes to slave: 0x00ae with repeat start true. [0001.949] E> I2C_DEV: Failed to send register address 0x00000000. [0001.955] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xae at 0x00000000 via instance 7. [0001.965] E> eeprom: Failed to read I2C slave device [0001.970] I> Eeprom read failed 0x3526070d [0001.974] I> Find /i2c@c240000's alias i2c1 [0001.978] I> Reading eeprom i2c=1 address=0x51 [0001.983] E> I2C: slave not found in slaves. [0001.987] E> I2C: Could not write 0 bytes to slave: 0x00a2 with repeat start true. [0001.995] E> I2C_DEV: Failed to send register address 0x00000000. [0002.001] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa2 at 0x00000000 via instance 1. [0002.011] E> eeprom: Retry to read I2C slave device. [0002.015] E> I2C: slave not found in slaves. [0002.020] E> I2C: Could not write 0 bytes to slave: 0x00a2 with repeat start true. [0002.027] E> I2C_DEV: Failed to send register address 0x00000000. [0002.033] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa2 at 0x00000000 via instance 1. [0002.043] E> eeprom: Failed to read I2C slave device [0002.047] I> Eeprom read failed 0x3526070d [0002.052] I> Find /i2c@3160000's alias i2c0 [0002.056] I> Reading eeprom i2c=0 address=0x50 [0002.060] E> I2C: slave not found in slaves. [0002.064] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true. [0002.072] E> I2C_DEV: Failed to send register address 0x00000000. [0002.078] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0x00000000 via instance 0. [0002.088] E> eeprom: Failed to read I2C slave device [0002.092] I> Eeprom read failed 0x3526070d [0002.097] I> Find /i2c@3180000's alias i2c2 [0002.101] I> Reading eeprom i2c=2 address=0x54 [0002.105] I> Enabling gpio chip_id = 2, gpio pin = 9 [0002.110] C> GPIO driver for chip_id 0x2 could not be found [0002.115] E> cam_eeprom_read: Can't get gpio driver [0002.120] I> Eeprom read failed 0x4d4d000d [0002.124] I> Reading eeprom i2c=2 address=0x57 [0002.128] I> Enabling gpio chip_id = 2, gpio pin = 9 [0002.133] C> GPIO driver for chip_id 0x2 could not be found [0002.138] E> cam_eeprom_read: Can't get gpio driver [0002.143] I> Eeprom read failed 0x4d4d000d [0002.147] I> create_pm_ids: id: 3310-1000-D00-P, len: 15 [0002.152] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0002.187] I> enabling 'vdd-hdmi' regulator [0002.191] E> tegrabl_display_get_pdata, failed to parse dtb settings [0002.200] E> cannot find any other nvdisp nodes [0002.204] E> no valid display unit config found in dtb [0002.210] W> display init failed [0002.213] initializing target [0002.216] calling apps_init() [0002.219] starting app kernel_boot_app [0002.241] I> found decompressor handler: lz4-legacy [0002.246] I> decompressing BMP blob ... [0002.258] I> Kernel type = Normal [0002.261] I> ########## Fixed storage boot ########## [0002.266] I> Loading kernel-bootctrl from partition [0002.271] I> Loading partition kernel-bootctrl at 0xa8000000 from device(0x1) [0002.285] W> tegrabl_get_kernel_bootctrl: magic number(0x00000000) is invalid [0002.292] W> tegrabl_get_kernel_bootctrl: use default dummy boot control data [0002.299] W> No valid slot number is found in scratch register [0002.304] W> Return default slot: _a [0002.308] I> A/B: bin_type (24) slot 0 [0002.323] I> Boot image size read from image header: 1fde008 [0002.329] I> Boot image load address: 0x80400000 [0002.333] I> Loading kernel from partition [0002.337] I> Loading partition kernel at 0x80400000 from device(0x1) [0003.279] I> Validate kernel ... [0003.282] I> T18x: Authenticate kernel (bin_type 24), max size 0x4000000 [0003.361] I> Decrypt the buffer ... [0003.364] W> tegrabl_decrypt_block: fuse (0x0) is not burnt to do encryption (0x4); skip decryption. [0003.373] I> done [0003.375] I> Checking boot.img header magic ... [0003.379] I> [OK] [0003.381] I> kernel-dtb is already loaded [0003.384] I> Validate kernel-dtb ... [0003.388] I> T18x: Authenticate kernel-dtb (bin_type 21), max size 0x100000 [0003.395] I> Decrypt the buffer ... [0003.399] W> tegrabl_decrypt_block: fuse (0x0) is not burnt to do encryption (0x4); skip decryption. [0003.407] I> done [0003.409] I> Kernel hdr @0x80400000 [0003.413] I> Kernel dtb @0x80000000 [0003.416] I> decompressor handler not found [0003.420] I> Copying kernel image (33415176 bytes) from 0x80400800 to 0x82600000 ... [0003.440] I> Done [0003.442] I> Move ramdisk (len: 0) from 0x823df000 to 0x96710000 [0003.449] I> Updated bpmp info to DTB [0003.455] I> Ramdisk: Base: 0x96710000; Size: 0x0 [0003.460] I> Updated initrd info to DTB [0003.464] W> WARN: Fail to override "console=none" in commandline [0003.469] I> Active rootfs suffix: [0003.473] E> tegrabl_linuxboot_add_disp_param, du 0 failed to get display params [0003.480] E> tegrabl_linuxboot_add_disp_param, du 0 failed to get display params [0003.487] E> tegrabl_linuxboot_add_disp_param, du 0 failed to get display params [0003.494] I> disabled_core_mask: 0xffffff0c [0003.498] W> No valid slot number is found in scratch register [0003.504] W> Return default slot: _a [0003.507] I> Active slot suffix: [0003.511] I> add_boot_slot_suffix: slot_suffix = [0003.515] I> Linux Cmdline: console=ttyS0,115200 androidboot.presilicon=true firmware_class.path=/etc/firmware root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map: [0003.563] I> Updated bootarg info to DTB [0003.566] I> eeprom_get_mac_addr: MAC (type: 0): 48:b0:2d:48:5a:25 [0003.573] I> eeprom_get_mac_addr: MAC (type: 1): 48:b0:2d:48:5a:26 [0003.579] I> eeprom_get_mac_addr: MAC (type: 2): 48:b0:2d:48:5a:27 [0003.585] E> Found no plugin manager ids in source DT [0003.590] W> Add plugin manager ids from board info [0003.595] W> "plugin-manager" doesn't exist, creating [0003.600] W> "ids" doesn't exist, creating [0003.604] W> "connection" doesn't exist, creating [0003.608] W> "configs" doesn't exist, creating [0003.613] I> create_pm_ids: id: 3310-1000-D00-P, len: 15 [0003.618] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0003.629] I> Adding plugin-manager/ids/3310-1000-D00=/i2c@c250000:module@0x50 [0003.636] W> "i2c@c250000" doesn't exist, creating [0003.641] W> "module@0x50" doesn't exist, creating [0003.647] I> Adding plugin-manager/ids/3310-1000-D00-P [0003.654] I> Adding plugin-manager/configs/3310-mem-type 00 [0003.660] I> Adding plugin-manager/configs/3310-power-config 00 [0003.666] I> Adding plugin-manager/configs/3310-misc-config 00 [0003.672] I> Adding plugin-manager/configs/3310-modem-config 00 [0003.678] I> Adding plugin-manager/configs/3310-touch-config 00 [0003.684] I> Adding plugin-manager/configs/3310-display-config 00 [0003.690] I> Adding plugin-manager/cvm [0003.694] W> "chip-id" doesn't exist, creating [0003.698] I> Adding plugin-manager/chip-id/A02P [0003.703] W> "odm-data" doesn't exist, creating [0003.707] I> Adding /chosen/plugin-manager/odm-data [0003.717] I> added [base:0x80000000, size:0x70000000] to /memory [0003.723] I> added [base:0xf0200000, size:0x185600000] to /memory [0003.729] I> added [base:0x275e00000, size:0x200000] to /memory [0003.735] I> added [base:0x276600000, size:0x200000] to /memory [0003.740] I> added [base:0x277000000, size:0x200000] to /memory [0003.746] I> Updated memory info to DTB [0003.751] E> add_disp_param: failed to get display params for du=0 [0003.758] W> "reset" doesn't exist, creating [0003.763] W> "pmc-reset-reason" doesn't exist, creating [0003.768] W> "pmic-reset-reason" doesn't exist, creating [0003.775] I> Adding ecid(00000001640221001400000015fc8440) to DT [0003.780] I> disabled_core_mask: 0xffffff0c [0003.793] I> Add serial number:1561621034810 as DT property [0003.802] I> Plugin-manager override starting [0003.808] I> node /plugin-manager/fragement@0 matches [0003.818] I> node /plugin-manager/fragement@4 matches [0003.831] I> node /plugin-manager/fragment-sdwake-p3310-1000-300 matches [0003.851] I> node /plugin-manager/fragement-pmon-p3310-1000-300 matches [0003.860] I> node /plugin-manager/fragement-pmon-p3310-1000-800 matches [0003.869] I> node /plugin-manager/fragment-devslp@0 matches [0003.881] I> node /plugin-manager/fragment-500-pcie-config matches [0003.896] I> node /plugin-manager/fragment-500-xusb-config matches [0003.919] I> node /plugin-manager/fragment-p3310-c00-comm matches [0003.932] I> node /plugin-manager/fragment-p3310-c00-pmic matches [0003.943] I> node /plugin-manager/fragment-p3310-c01 matches [0003.956] I> node /plugin-manager/fragment-p3310-c03 matches [0004.002] I> node /plugin-manager/fragment-p3310-c00-camera matches [0004.028] I> Disable plugin-manager status in FDT [0004.033] I> Plugin-manager override finished successfully [0004.038] I> tegrabl_load_kernel_and_dtb: Done [0004.042] E> tegrabl_display_clear: display is not initialized [0004.048] W> Boot logo display failed... [0004.052] I> Kernel EP: 0x82600000, DTB: 0x80000000 [ 0.000000] Booting Linux on physical CPU 0x100 [ 0.000000] Linux version 4.9.253 (root@ubuntu-HP-288-Pro-G6-Microtower-PC) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #2 [ 0.000000] Boot CPU: AArch64 Processor [411fd073] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 80, [ 0.000000] OF: fdt: - 80000000 , 70000000 [ 0.000000] OF: fdt: - f0200000 , 185600000 [ 0.000000] OF: fdt: - 275e00000 , 200000 [ 0.000000] OF: fdt: - 276600000 , 200000 [ 0.000000] OF: fdt: - 277000000 , 200000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000003100000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fc000000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 23 pages/cpu s57112 r8192 d28904 u94208 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2022968 [ 0.000000] Kernel command line: console=ttyS0,115200 androidboot.presilicon=true firmware_class.path=/etc/firmware root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbc [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 163840 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 262144 bytes [ 0.000000] early log buf free: 29988(91%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Memory: 7285804K/8220672K available (15102K kernel code, 2488K rwdata, 6532K rodata, 8448K init, 595K bss, 181204K reserved, 753664K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008200000 - 0xffffff80090c0000 ( 15104 KB) [ 0.000000] .rodata : 0xffffff80090c0000 - 0xffffff8009730000 ( 6592 KB) [ 0.000000] .init : 0xffffff8009730000 - 0xffffff8009f70000 ( 8448 KB) [ 0.000000] .data : 0xffffff8009f70000 - 0xffffff800a1de008 ( 2489 KB) [ 0.000000] .bss : 0xffffff800a1de008 - 0xffffff800a272d34 ( 596 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf07dc8000 ( 125 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc1f7200000 ( 8050 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=6. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 31.25MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xe6a171046, max_idle_ns: 881590405314 ns [ 0.000003] sched_clock: 56 bits at 31MHz, resolution 32ns, wraps every 4398046511088ns [ 0.009904] Console: colour dummy device 80x25 [ 0.014565] console [tty0] enabled [ 0.018120] bootconsole [uart8250] disabled [ 0.000000] Booting Linux on physical CPU 0x100 [ 0.000000] Linux version 4.9.253 (root@ubuntu-HP-288-Pro-G6-Microtower-PC) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #2 [ 0.000000] Boot CPU: AArch64 Processor [411fd073] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 80, [ 0.000000] OF: fdt: - 80000000 , 70000000 [ 0.000000] OF: fdt: - f0200000 , 185600000 [ 0.000000] OF: fdt: - 275e00000 , 200000 [ 0.000000] OF: fdt: - 276600000 , 200000 [ 0.000000] OF: fdt: - 277000000 , 200000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000003100000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fc000000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 23 pages/cpu s57112 r8192 d28904 u94208 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2022968 [ 0.000000] Kernel command line: console=ttyS0,115200 androidboot.presilicon=true firmware_class.path=/etc/firmware root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbc [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 163840 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 262144 bytes [ 0.000000] early log buf free: 29988(91%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Memory: 7285804K/8220672K available (15102K kernel code, 2488K rwdata, 6532K rodata, 8448K init, 595K bss, 181204K reserved, 753664K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008200000 - 0xffffff80090c0000 ( 15104 KB) [ 0.000000] .rodata : 0xffffff80090c0000 - 0xffffff8009730000 ( 6592 KB) [ 0.000000] .init : 0xffffff8009730000 - 0xffffff8009f70000 ( 8448 KB) [ 0.000000] .data : 0xffffff8009f70000 - 0xffffff800a1de008 ( 2489 KB) [ 0.000000] .bss : 0xffffff800a1de008 - 0xffffff800a272d34 ( 596 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf07dc8000 ( 125 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc1f7200000 ( 8050 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=6. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 31.25MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xe6a171046, max_idle_ns: 881590405314 ns [ 0.000003] sched_clock: 56 bits at 31MHz, resolution 32ns, wraps every 4398046511088ns [ 0.009904] Console: colour dummy device 80x25 [ 0.014565] console [tty0] enabled [ 0.018120] bootconsole [uart8250] disabled [ 0.022494] kmemleak: Kernel memory leak detector disabled [ 0.022509] Calibrating delay loop (skipped), value calculated using timer frequency.. 62.50 BogoMIPS (lpj=125000) [ 0.022523] pid_max: default: 32768 minimum: 301 [ 0.022838] Security Framework initialized [ 0.023001] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.023010] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.023602] ftrace: allocating 46362 entries in 182 pages [ 0.145839] sched-energy: Sched-energy-costs installed from DT [ 0.145858] ASID allocator initialised with 65536 entries [ 0.184504] tegra-id: chipid=21817. [ 0.184518] tegra-id: opt_subrevision=1. [ 0.184539] Tegra Revision: A02p SKU: 0xdc CPU Process: 0 SoC Process: 0 [ 0.184552] DTS File Name: arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t18x/quill/kernel-dts/tegra186-quill-p3310-1000-c03-00-base.dts [ 0.184566] DTB Build time: Jun 27 2022 20:05:39 [ 0.235104] CPU1: Booted secondary processor [4e0f0030] [ 0.266509] CPU2: Booted secondary processor [4e0f0030] [ 0.297505] CPU3: Booted secondary processor [411fd073] [ 0.329469] CPU4: Booted secondary processor [411fd073] [ 0.361459] CPU5: Booted secondary processor [411fd073] [ 0.361511] Brought up 6 CPUs [ 0.361546] SMP: Total of 6 processors activated. [ 0.361557] CPU features: detected feature: 32-bit EL0 Support [ 0.363681] CPU: All CPU(s) started at EL2 [ 0.363847] alternatives: patching kernel code [ 0.366755] devtmpfs: initialized [ 0.406832] Initilizing CustomIPI irq domain [ 0.406991] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.407015] futex hash table entries: 2048 (order: 5, 131072 bytes) [ 0.414933] pinctrl core: initialized pinctrl subsystem [ 0.415178] OS set in device tree is not L4T. [ 0.415352] regulator-dummy: no parameters [ 0.415497] Initializing plugin-manager [ 0.415564] Plugin module not found [ 0.415609] Plugin-manager status disabled [ 0.417569] NET: Registered protocol family 16 [ 0.418616] pstore: using zlib compression [ 0.418874] console [pstore-1] enabled [ 0.418884] pstore: Registered ramoops as persistent store backend [ 0.418897] ramoops: attached 0x200000@0x275880000, ecc: 0/0 [ 0.441050] cpuidle: using governor menu [ 0.442566] bpmp: waiting for handshake [ 0.442582] bpmp: handshake completed [ 0.442604] bpmp: synchronizing channels [ 0.442623] bpmp: channels synchronized [ 0.442634] bpmp: mail init ok [ 0.444761] arm-smmu 12000000.iommu: probing hardware configuration... [ 0.444779] arm-smmu 12000000.iommu: SMMUv2 with: [ 0.444792] arm-smmu 12000000.iommu: stage 1 translation [ 0.444804] arm-smmu 12000000.iommu: stage 2 translation [ 0.444816] arm-smmu 12000000.iommu: nested translation [ 0.444831] arm-smmu 12000000.iommu: stream matching with 128 register groups, mask 0x7f80 [ 0.444850] arm-smmu 12000000.iommu: SMMU address space size (0x800000) differs from mapped region size (0x1000000)! [ 0.444867] arm-smmu 12000000.iommu: 64 context banks (0 stage-2 only) [ 0.444881] arm-smmu 12000000.iommu: Stage-1: 39-bit VA -> 48-bit IPA [ 0.444894] arm-smmu 12000000.iommu: Stage-2: 39-bit IPA -> 48-bit PA [ 0.447102] vdso: 2 pages (1 code @ ffffff80090c7000, 1 data @ ffffff8009f74000) [ 0.447133] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.449296] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations [ 0.451459] Registering BPMP clocks... [ 0.451563] tegra_bpmp_clk_init: clock init ok (638 clks) [ 0.452542] Serial: AMBA PL011 UART driver [ 0.453706] tegra_powergate_init: DONE [ 0.453725] DTS File Name: arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t18x/quill/kernel-dts/tegra186-quill-p3310-1000-c03-00-base.dts [ 0.453747] DTB Build time: Jun 27 2022 20:05:39 [ 0.455955] Tegra reboot handler registered. [ 0.457580] tegra-pmc c360000.pmc: scratch reg offset dts data not present [ 0.457662] tegra-pmc: get_secure_pmc_setting: done secure_pmc=0 [ 0.457685] tegra-pmc: ### PMC reset source: TEGRA_SOFTWARE_RESET [ 0.457696] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_L1 [ 0.457708] tegra-pmc: ### PMC reset status reg: 0x2d [ 0.457869] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [ 0.457895] tegra-pmc c360000.pmc: IO padctrl driver initialized [ 0.458250] iommu: Adding device 3460000.sdhci to group 0 [ 0.458955] iommu: Adding device 3400000.sdhci to group 1 [ 0.460028] iommu: Adding device 3507000.ahci-sata to group 2 [ 0.460054] arm-smmu: forcing sodev map for 3507000.ahci-sata [ 0.460516] iommu: Adding device 3160000.i2c to group 3 [ 0.460982] iommu: Adding device c240000.i2c to group 4 [ 0.461349] iommu: Adding device 3180000.i2c to group 5 [ 0.461728] iommu: Adding device 3190000.i2c to group 6 [ 0.462169] iommu: Adding device 31b0000.i2c to group 7 [ 0.462519] iommu: Adding device 31c0000.i2c to group 8 [ 0.462872] iommu: Adding device c250000.i2c to group 9 [ 0.463225] iommu: Adding device 31e0000.i2c to group 10 [ 0.464749] iommu: Adding device 3210000.spi to group 11 [ 0.465106] iommu: Adding device c260000.spi to group 12 [ 0.465464] iommu: Adding device 3240000.spi to group 13 [ 0.466197] iommu: Adding device 3100000.serial to group 14 [ 0.466556] iommu: Adding device 3110000.serial to group 15 [ 0.466904] iommu: Adding device c280000.serial to group 16 [ 0.467249] iommu: Adding device 3130000.serial to group 17 [ 0.468662] iommu: Adding device 2490000.ether_qos to group 18 [ 0.468686] arm-smmu: forcing sodev map for 2490000.ether_qos [ 0.469628] iommu: Adding device b000000.rtcpu to group 19 [ 0.471877] iommu: Adding device 13e10000.host1x to group 20 [ 0.472201] iommu: Adding device 13e10000.host1x:ctx0 to group 21 [ 0.472534] iommu: Adding device 13e10000.host1x:ctx1 to group 22 [ 0.472848] iommu: Adding device 13e10000.host1x:ctx2 to group 23 [ 0.473165] iommu: Adding device 13e10000.host1x:ctx3 to group 24 [ 0.473517] iommu: Adding device 13e10000.host1x:ctx4 to group 25 [ 0.473841] iommu: Adding device 13e10000.host1x:ctx5 to group 26 [ 0.474154] iommu: Adding device 13e10000.host1x:ctx6 to group 27 [ 0.474479] iommu: Adding device 13e10000.host1x:ctx7 to group 28 [ 0.474962] iommu: Adding device 150c0000.nvcsi to group 29 [ 0.475621] iommu: Adding device 15700000.vi to group 30 [ 0.475990] iommu: Adding device 15600000.isp to group 31 [ 0.476222] iommu: Adding device 15200000.dc_common to group 32 [ 0.476865] iommu: Adding device 15210000.nvdisplay to group 33 [ 0.477243] iommu: Adding device 15340000.vic to group 34 [ 0.477494] iommu: Adding device 154c0000.nvenc to group 35 [ 0.477731] iommu: Adding device 15480000.nvdec to group 36 [ 0.478094] iommu: Adding device 15380000.nvjpg to group 37 [ 0.478322] iommu: Adding device 15500000.tsec to group 38 [ 0.478547] iommu: Adding device 15100000.tsecb to group 39 [ 0.479257] iommu: Adding device 15810000.se to group 40 [ 0.479488] iommu: Adding device 15820000.se to group 41 [ 0.479717] iommu: Adding device 15830000.se to group 42 [ 0.479944] iommu: Adding device 15840000.se to group 43 [ 0.480844] iommu: Adding device smmu_test to group 44 [ 0.481486] mc: mapped MMIO address: 0xffffff800a5e0000 -> 0x2c10000 [ 0.481511] mc: mapped MMIO address: 0xffffff800a7b0000 -> 0x2c20000 [ 0.481531] mc: mapped MMIO address: 0xffffff800a7d0000 -> 0x2c30000 [ 0.481552] mc: mapped MMIO address: 0xffffff800b010000 -> 0x2c40000 [ 0.481571] mc: mapped MMIO address: 0xffffff800b030000 -> 0x2c50000 [ 0.481589] nv-tegra-mc 2c10000.mc: No mssnvlink node [ 0.481608] mc-err: mcerr ops are set to t18x [ 0.481767] dram-ecc: DRAM ECC disabled-MC_ECC_CONTROL:0x0000000c [ 0.482958] iommu: Adding device 3530000.xhci to group 45 [ 0.482986] arm-smmu: forcing sodev map for 3530000.xhci [ 0.483449] iommu: Adding device 3550000.xudc to group 46 [ 0.483472] arm-smmu: forcing sodev map for 3550000.xudc [ 0.484198] tegra186-aowake c370000.pmc: WAKE_AOWAKE_CNTRL_83 = 0x10a [ 0.484217] tegra186-aowake c370000.pmc: WAKE_AOWAKE_CTRL_0 = 3 [ 0.484232] tegra186-aowake c370000.pmc: WAKE_AOWAKE_CNTRL_24(PMU_INT) = 256 [ 0.484894] iommu: Adding device 17000000.gp10b to group 47 [ 0.486022] tegra-reset 5000000.clock: registered 193 resets. [ 0.488304] iommu: Adding device d000000.bpmp to group 48 [ 0.488516] bpmp: ping status is 0 [ 0.488616] bpmp d000000.bpmp: firmware tag is 91572a54614f84d0fd0c270beec2c56f [ 0.491163] bpmp d000000.bpmp: probe ok [ 0.494427] iommu: Adding device 2600000.dma to group 49 [ 0.495328] gpio gpiochip0: gpio-line-names specifies 180 line names but there are 192 lines on the chip [ 0.495839] GPIO line 461 (camera-control-output-low) hogged as output/low [ 0.495881] GPIO line 456 (camera-control-output-low) hogged as output/low [ 0.495921] GPIO line 457 (camera-control-output-low) hogged as output/low [ 0.495959] GPIO line 426 (camera-control-output-low) hogged as output/low [ 0.496000] GPIO line 424 (wifi-enable) hogged as output/high [ 0.496039] GPIO line 445 (sdmmc-wake-support-input) hogged as input [ 0.496078] GPIO line 446 (sdmmc-wake-support-output) hogged as output/low [ 0.496247] gpiochip_setup_dev: registered GPIOs 320 to 511 on device: gpiochip0 (tegra-gpio) [ 0.499977] gpio gpiochip1: gpio-line-names specifies 60 line names but there are 64 lines on the chip [ 0.500111] GPIO line 315 (wifi-wake-ap) hogged as input [ 0.500263] gpiochip_setup_dev: registered GPIOs 256 to 319 on device: gpiochip1 (tegra-gpio-aon) [ 0.501955] iommu: Adding device 10003000.pcie-controller to group 50 [ 0.501983] arm-smmu: forcing sodev map for 10003000.pcie-controller [ 0.502335] iommu: Adding device sound to group 51 [ 0.502723] iommu: Adding device 3510000.hda to group 52 [ 0.510326] iommu: Adding device c1a0000.aon to group 53 [ 0.510790] vdd-ac-bat: 5000 mV [ 0.512486] vdd-1v8-ap: 1800 mV [ 0.522523] random: fast init done [ 0.538016] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.540748] eventlib_kernel: keventlib is initialized, test id: 0 [ 0.540961] SCSI subsystem initialized [ 0.541254] usbcore: registered new interface driver usbfs [ 0.541298] usbcore: registered new interface driver hub [ 0.541336] usbcore: registered new device driver usb [ 0.543482] tegra-i2c 3160000.i2c: no acknowledge from address 0x74 [ 0.543529] pca953x 0-0074: failed reading register [ 0.543576] pca953x: probe of 0-0074 failed with error -121 [ 0.543929] tegra-i2c 3160000.i2c: no acknowledge from address 0x77 [ 0.543971] pca953x 0-0077: failed reading register [ 0.544010] pca953x: probe of 0-0077 failed with error -121 [ 0.553247] max77620 4-003c: henry teset at max77620 [ 0.553266] henry test at max77620 611 [ 0.554268] max77620 4-003c: PMIC Version OTP:0x45 and ES:0x8 [ 0.557735] vddio-ddr: at 1125 mV [ 0.561515] avdd_dsi_csi: 1200 mV [ 0.565515] vdd-1v8: 1800 mV [ 0.569513] vdd-3v3-sys: 3300 mV [ 0.570392] spmic-ldo0: at 1800 mV [ 0.571111] spmic-ldo1: at 800 mV [ 0.573515] vddio-3v3: 3300 mV [ 0.574255] vddio-sdmmc1: 1800 <--> 3300 mV at 3300 mV [ 0.577515] vdd-rtc: at 800 mV [ 0.578140] avdd-ts-hv: 1800 <--> 3300 mV at 1800 mV [ 0.581514] spmic-ldo6: at 1500 mV [ 0.585514] vdd-pex-1v00: 1000 mV [ 0.586155] dvdd-pex: 1000 mV [ 0.588506] GPIO line 253 (spmic_gpio_input) hogged as input [ 0.588669] GPIO line 254 (spmic_gpio_input) hogged as input [ 0.588844] gpiochip_setup_dev: registered GPIOs 248 to 255 on device: gpiochip2 (max77620-gpio) [ 0.589047] max77620 4-003c: max77620 probe successful [ 0.589459] media: Linux media interface: v0.10 [ 0.589512] Linux video capture interface: v2.00 [ 0.593171] pps_core: LinuxPPS API ver. 1 registered [ 0.593187] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.593216] PTP clock support registered [ 0.593425] tegra_wdt_t18x 30c0000.watchdog: Expiry count is deprecated [ 0.593663] tegra_wdt_t18x 30c0000.watchdog: Tegra WDT init timeout = 120 sec [ 0.593692] tegra_wdt_t18x 30c0000.watchdog: Registered successfully [ 0.594871] trusty trusty: trusty version: Built: 12:20:14 Jul 26 2021 [ 0.594903] trusty trusty: selected api version: 3 (requested 3) [ 0.595712] Advanced Linux Sound Architecture Driver Initialized. [ 0.596080] Bluetooth: Core ver 2.22 [ 0.596120] NET: Registered protocol family 31 [ 0.596132] Bluetooth: HCI device and connection manager initialized [ 0.596148] Bluetooth: HCI socket layer initialized [ 0.596160] Bluetooth: L2CAP socket layer initialized [ 0.596182] Bluetooth: SCO socket layer initialized [ 0.596735] en-vdd-sd: 3300 mV [ 0.597131] vdd-usb0-5v: 5000 mV [ 0.597414] vdd-usb1-5v: 5000 mV [ 0.597911] vdd-3v3: 3300 mV [ 0.598169] en-vdd-vcm-2v8: 2800 mV [ 0.598412] vdd-sys-bl: 3300 mV [ 0.600440] camchar: rtcpu character device driver loaded [ 0.600968] gpio tegra-gpio wake53 for gpio=159(X:7) [ 0.602706] extcon-gpio-states external-connection:extcon@1: Cable state:1, cable id:1 [ 0.603572] clocksource: Switched to clocksource arch_sys_counter [ 0.625822] VFS: Disk quotas dquot_6.6.0 [ 0.625915] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.626177] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.626713] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000c6000000, size=0x2a000000 [ 0.626848] cma: enabled page replacement for spfn=c6000, epfn=f0000 [ 0.626863] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful [ 0.626879] nvmap: nvmap_select_cache_ops() nvmap cache ops set to roc [ 0.626896] nvmap_page_pool_init: Total RAM pages: 2009867 [ 0.626908] nvmap_page_pool_init: nvmap page pool size: 251233 pages (981 MB) [ 0.626966] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.627422] misc nvmap: created heap vpr base 0x00000000c6000000 size (688128KiB) [ 0.629359] tegra-gpcdma 2600000.dma: GPC DMA driver register 32 channels [ 0.634973] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type BCPU-therm [ 0.635220] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type MCPU-therm [ 0.635707] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm [ 0.635799] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [ 0.635918] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type Tboard_tegra [ 0.636042] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type Tdiode_tegra [ 0.636222] thermal thermal_zone6: Registering thermal zone thermal_zone6 for type PMIC-Die [ 0.636432] la/ptsa driver initialized. [ 0.636450] pre_t19x_iso_plat_init(): iso emc max clk=1866000KHz [ 0.636462] pre_t19x_iso_plat_init(): max_iso_bw=26870400KB [ 0.636765] NET: Registered protocol family 2 [ 0.637429] TCP established hash table entries: 65536 (order: 7, 524288 bytes) [ 0.637753] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.638357] TCP: Hash tables configured (established 65536 bind 65536) [ 0.638416] UDP hash table entries: 4096 (order: 5, 131072 bytes) [ 0.638542] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes) [ 0.638878] NET: Registered protocol family 1 [ 0.639201] RPC: Registered named UNIX socket transport module. [ 0.639215] RPC: Registered udp transport module. [ 0.639226] RPC: Registered tcp transport module. [ 0.639236] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.639360] Trying to unpack rootfs image as initramfs... [ 0.655160] host1x 13e10000.host1x: initialized [ 0.656480] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.658537] audit: initializing netlink subsys (disabled) [ 0.658576] audit: type=2000 audit(0.536:1): initialized [ 0.658959] workingset: timestamp_bits=46 max_order=21 bucket_order=0 [ 0.665425] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.666384] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.666903] 9p: Installing v9fs 9p2000 file system support [ 0.669011] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240) [ 0.669084] io scheduler noop registered [ 0.669294] io scheduler cfq registered (default) [ 0.672674] gic 2a41000.agic-controller: GIC IRQ controller registered [ 0.780078] iommu: Adding device aconnect@2a41000:adsp_audio to group 54 [ 0.815556] iommu: Adding device 2993000.adsp to group 55 [ 0.816633] tegra-aconnect aconnect@2a41000: Tegra ACONNECT bus registered [ 0.819161] tegra-xusb-padctl 3520000.xusb_padctl: VBUS over-current detection enabled [ 0.822512] tegra-pwm 3280000.pwm: PWM clk can sleep in ops [ 0.823709] tegra-pwm 3290000.pwm: PWM clk can sleep in ops [ 0.824816] tegra-pwm 32a0000.pwm: PWM clk can sleep in ops [ 0.825920] tegra-pwm c340000.pwm: PWM clk can sleep in ops [ 0.828355] tegra-pcie 10003000.pcie-controller: 4x1, 1x1 configuration [ 0.829321] tegra-pcie 10003000.pcie-controller: PCIE: Enable power rails [ 0.829672] tegra-pcie 10003000.pcie-controller: probing port 0, using 4 lanes [ 0.829776] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [ 0.829892] misc tegra_camera_ctrl: tegra_camera_isomgr_register tpg_max_iso = 3916800KBs [ 0.829912] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1000000, vi_iso_bw=750000, max_bw=3916800 [ 0.831931] tegra-pcie 10003000.pcie-controller: probing port 2, using 1 lanes [ 0.833230] tsec 15500000.tsec: initialized [ 0.834387] tsec 15100000.tsecb: initialized [ 0.837638] nvdec 15480000.nvdec: initialized [ 0.843425] falcon 15340000.vic: initialized [ 0.844835] falcon 154c0000.nvenc: initialized [ 0.846063] falcon 15380000.nvjpg: initialized [ 0.847965] iommu_context_dev 13e10000.host1x:ctx0: initialized (streamid=56) [ 0.849404] iommu_context_dev 13e10000.host1x:ctx1: initialized (streamid=57) [ 0.850883] iommu_context_dev 13e10000.host1x:ctx2: initialized (streamid=58) [ 0.852379] iommu_context_dev 13e10000.host1x:ctx3: initialized (streamid=59) [ 0.853832] iommu_context_dev 13e10000.host1x:ctx4: initialized (streamid=60) [ 0.855261] iommu_context_dev 13e10000.host1x:ctx5: initialized (streamid=61) [ 0.856720] iommu_context_dev 13e10000.host1x:ctx6: initialized (streamid=62) [ 0.858162] iommu_context_dev 13e10000.host1x:ctx7: initialized (streamid=63) [ 0.861484] tegradccommon 15200000.dc_common: host1x channel mapped [ 0.861505] tegradccommon 15200000.dc_common: dc_common syncpt # 1 allocated [ 0.861542] tegradccommon 15200000.dc_common: dma mapping done [ 0.862308] tegra_cec 3960000.tegra_cec: dt=1 start=0x03960000 end=0x03960FFF irq=391 [ 0.862458] tegradc 15210000.nvdisplay: disp0 connected to head1->/host1x/sor1 [ 0.862515] generic_infoframe_type: 0x87 [ 0.862604] tegradc 15210000.nvdisplay: DT parsed successfully [ 0.862631] tegradc 15210000.nvdisplay: Display dc.ffffff800b3a0000 registered with id=0 [ 0.863010] tegra_cec 3960000.tegra_cec: Unpowergate DISP: 0. [ 0.863785] tegra_cec 3960000.tegra_cec: Enable clock result: 0. [ 0.863810] tegra_cec 3960000.tegra_cec: tegra_cec_init started [ 0.863972] tegra_cec 3960000.tegra_cec: cec_add_sysfs ret=0 [ 0.863986] tegra_cec 3960000.tegra_cec: probed [ 0.868076] tegra_nvdisp_bandwidth_register_max_config: max config iso bw = 16727000 KB/s [ 0.868098] tegra_nvdisp_bandwidth_register_max_config: max config EMC floor = 665600000 Hz [ 0.868115] tegra_nvdisp_bandwidth_register_max_config: max config hubclk = 357620000 Hz [ 0.868333] tegradc 15210000.nvdisplay: vblank syncpt # 8 for dc 1 [ 0.868350] tegradc 15210000.nvdisplay: vpulse3 syncpt # 9 for dc 1 [ 0.869130] tegradc 15210000.nvdisplay: dc_hdmi_hotplug_init: couldn't get regulator vdd_hdmi_5v0, -517 [ 0.874239] tegradc 15210000.nvdisplay: hdmi: invalid prod list prod_list_hdmi_board [ 0.874260] tegradc 15210000.nvdisplay: hdmi: tegra_hdmi_tmds_range_read(bd) failed [ 0.878073] tegra-i2c 3190000.i2c: arb lost in communicate to add 0x50 [ 0.878218] tegra-i2c 3190000.i2c: Un-recovered Arb lost [ 0.879194] tegra-adma 2930000.adma: Tegra210 ADMA driver registered 32 channels [ 0.880051] tegra-fuse-burn 3820000.efuse:efuse-burn: shutdown limit check disabled [ 0.880168] tegra-fuse-burn 3820000.efuse:efuse-burn: Fuse burn driver initialized [ 0.880919] kfuse 3830000.kfuse: initialized [ 0.881635] tegradc 15210000.nvdisplay: probed [ 0.881978] Console: switching to colour frame buffer device 80x30 [ 0.882008] tegradc 15210000.nvdisplay: fb registered [ 0.882180] gpio tegra-gpio wake21 for gpio=121(P:1) [ 0.882362] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0 [ 0.883030] tegra_nvdisp_handle_pd_enable: Unpowergated Head0 pd [ 0.883124] tegra_nvdisp_handle_pd_enable: Unpowergated Head1 pd [ 0.883215] tegra_nvdisp_handle_pd_enable: Unpowergated Head2 pd [ 0.885333] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.891151] Parent Clock set for DC plld2 [ 0.891381] console [ttyS0] disabled [ 0.891413] 3100000.serial: ttyS0 at MMIO 0x3100000 (irq = 36, base_baud = 25500000) is a Tegra [ 0.894230] edid invalid [ 0.894943] tegradc 15210000.nvdisplay: hdmi: tmds rate:25200K prod-setting:prod_c_hdmi_0m_54m [ 0.896194] tegradc 15210000.nvdisplay: hdmi: get YCC quant from EDID. [ 0.899766] tegra-i2c 3190000.i2c: arb lost in communicate to add 0x50 [ 0.899894] tegra-i2c 3190000.i2c: Un-recovered Arb lost [ 0.903504] extcon-disp-state external-connection:disp-state: cable 47 state 1 [ 0.903506] Extcon AUX1(HDMI) enable [ 1.010898] tegra-i2c 3190000.i2c: arb lost in communicate to add 0x50 [ 1.011028] tegra-i2c 3190000.i2c: Un-recovered Arb lost [ 1.014843] tegra-i2c 3190000.i2c: arb lost in communicate to add 0x50 [ 1.014972] tegra-i2c 3190000.i2c: Un-recovered Arb lost [ 1.018778] tegra-i2c 3190000.i2c: arb lost in communicate to add 0x50 [ 1.018906] tegra-i2c 3190000.i2c: Un-recovered Arb lost [ 1.022715] tegra-i2c 3190000.i2c: arb lost in communicate to add 0x50 [ 1.022843] tegra-i2c 3190000.i2c: Un-recovered Arb lost [ 1.026647] tegra-i2c 3190000.i2c: arb lost in communicate to add 0x50 [ 1.026776] tegra-i2c 3190000.i2c: Un-recovered Arb lost [ 1.030579] tegra-i2c 3190000.i2c: arb lost in communicate to add 0x50 [ 1.030708] tegra-i2c 3190000.i2c: Un-recovered Arb lost [ 1.034511] tegra-i2c 3190000.i2c: arb lost in communicate to add 0x50 [ 1.034639] tegra-i2c 3190000.i2c: Un-recovered Arb lost [ 1.038443] tegra-i2c 3190000.i2c: arb lost in communicate to add 0x50 [ 1.038572] tegra-i2c 3190000.i2c: Un-recovered Arb lost [ 1.042375] tegra-i2c 3190000.i2c: arb lost in communicate to add 0x50 [ 1.042503] tegra-i2c 3190000.i2c: Un-recovered Arb lost [ 1.046307] tegra-i2c 3190000.i2c: arb lost in communicate to add 0x50 [ 1.046436] tegra-i2c 3190000.i2c: Un-recovered Arb lost [ 1.046923] tegradc 15210000.nvdisplay: hdmi: edid read failed [ 1.046968] tegradc 15210000.nvdisplay: hdmi: using fallback edid [ 1.257051] tegra-pcie 10003000.pcie-controller: link 0 down, retrying [ 1.661185] tegra-pcie 10003000.pcie-controller: link 0 down, retrying [ 1.879557] tegra_cec 3960000.tegra_cec: physical address: 10:00. [ 1.944077] tegra_cec 3960000.tegra_cec: Sent res: -113. [ 1.944080] tegra_cec 3960000.tegra_cec: tegra_cec_init Done. [ 2.065348] tegra-pcie 10003000.pcie-controller: link 0 down, retrying [ 2.067364] tegra-pcie 10003000.pcie-controller: link 0 down, ignoring [ 2.469501] tegra-pcie 10003000.pcie-controller: link 2 down, retrying [ 2.873669] tegra-pcie 10003000.pcie-controller: link 2 down, retrying [ 3.277820] tegra-pcie 10003000.pcie-controller: link 2 down, retrying [ 3.279839] tegra-pcie 10003000.pcie-controller: link 2 down, ignoring [ 3.478211] console [ttyS0] enabled [ 3.478217] tegradc 15210000.nvdisplay: blank - powerdown [ 3.479790] 3110000.serial: ttyTHS1 at MMIO 0x3110000 (irq = 37, base_baud = 0) is a TEGRA_UART [ 3.480706] c280000.serial: ttyTHS2 at MMIO 0xc280000 (irq = 38, base_baud = 0) is a TEGRA_UART [ 3.480873] serial-tegra 3130000.serial: RX in PIO mode [ 3.481639] 3130000.serial: ttyTHS3 at MMIO 0x3130000 (irq = 39, base_baud = 0) is a TEGRA_UART [ 3.482674] [drm] Initialized [ 3.485115] tegra-pcie 10003000.pcie-controller: PCIE: no end points detected [ 3.485370] tegra-pcie 10003000.pcie-controller: PCIE: Disable power rails [ 3.500435] brd: module loaded [ 3.503826] loop: module loaded [ 3.503872] tegra_profiler: version: 1.145, samples/io: 49/28 [ 3.503945] tegra_profiler: auth: init [ 3.504308] nct1008_nct72 7-004c: starting parse dt [ 3.504408] nct1008_nct72 7-004c: !!!Found deprecated property!!! [ 3.504412] nct1008_nct72 7-004c: success parsing dt [ 3.504516] nct1008_nct72 7-004c: success in enabling tmp451 VDD rail [ 3.504885] THERMAL EST: found 3 subdevs [ 3.504888] THERMAL EST num_resources: 0 [ 3.504891] [THERMAL EST subdev 0] [ 3.504895] [THERMAL EST subdev 1] [ 3.504897] [THERMAL EST subdev 2] [ 3.505148] thermal thermal_zone7: Registering thermal zone thermal_zone7 for type thermal-fan-est [ 3.505149] THERMAL EST: thz register success. [ 3.505239] THERMAL EST: end of probe, return err: 0 [ 3.505856] sd: No Scsi addr parsed to reserve index [ 3.505877] hisi_sas: driver version v1.6 [ 3.509504] tegra-ahci 3507000.ahci-sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 3.509510] tegra-ahci 3507000.ahci-sata: flags: 64bit ncq sntf pm led pmp pio slum part deso sadm apst [ 3.510237] scsi host0: tegra_ahci [ 3.510616] scsi host1: tegra_ahci [ 3.510756] ata1: SATA max UDMA/133 mmio [mem 0x03507000-0x03508fff] port 0x100 irq 24 [ 3.510758] ata2: DUMMY [ 3.513036] extcon-disp-state external-connection:disp-state: cable 47 state 0 [ 3.513038] Extcon AUX1(HDMI) disable [ 3.516253] libphy: Fixed MDIO Bus: probed [ 3.516707] tun: Universal TUN/TAP device driver, 1.6 [ 3.516709] tun: (C) 1999-2004 Max Krasnyansky [ 3.517424] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 3.517426] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.517457] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 3.517458] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.517494] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 3.517495] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 3.517526] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 4.4.0-k [ 3.517528] ixgbe: Copyright (c) 1999-2016 Intel Corporation. [ 3.527624] eqos 2490000.ether_qos: can't get pllrefe_vcoout clk (-2) [ 3.530165] eqos 2490000.ether_qos: failed to read eqos_auto_cal_config_0_reg [ 3.530649] eqos 2490000.ether_qos: Setting local MAC: 48 b0 2d 48 5a 27 [ 3.530679] Using phyrst_lpmode = 0 from DT [ 3.530752] libphy: dwc_phy: probed [ 3.531036] bcm54xx_low_power_mode(): put phy in iddq-lp mode [ 3.533117] PPP generic driver version 2.4.2 [ 3.533231] PPP BSD Compression module registered [ 3.533233] PPP Deflate Compression module registered [ 3.533247] PPP MPPE Compression module registered [ 3.533250] NET: Registered protocol family 24 [ 3.533287] usbcore: registered new interface driver r8152 [ 3.533320] usbcore: registered new interface driver asix [ 3.533352] usbcore: registered new interface driver ax88179_178a [ 3.533380] usbcore: registered new interface driver cdc_ether [ 3.533404] usbcore: registered new interface driver net1080 [ 3.533429] usbcore: registered new interface driver cdc_subset [ 3.533462] usbcore: registered new interface driver zaurus [ 3.533494] usbcore: registered new interface driver cdc_ncm [ 3.533595] VFIO - User Level meta-driver version: 0.3 [ 3.534416] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.534426] ehci-pci: EHCI PCI platform driver [ 3.534455] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.534469] ohci-pci: OHCI PCI platform driver [ 3.534498] ohci-platform: OHCI generic platform driver [ 3.540077] nct1008_nct72 7-004c: LOC shutdown limit 107 [ 3.540590] tegra_nvdisp_handle_pd_disable: Powergated Head2 pd [ 3.540606] nct1008_nct72 7-004c: EXT shutdown limit 107 [ 3.541450] tegra_nvdisp_handle_pd_disable: Powergated Head1 pd [ 3.550574] tegra_nvdisp_handle_pd_disable: Powergated Head0 pd [ 3.566015] tegra-xusb 3530000.xhci: USB2 port 0 has OTG_CAP [ 3.576814] nct1008_nct72 7-004c: initial LOC temp: 31000 [ 3.577273] nct1008_nct72 7-004c: initial EXT temp: 32500 [ 3.577527] tegra-xusb 3530000.xhci: extcon 0: ffffffc1eb3ba800 id [ 3.578173] nct1008_nct72 7-004c: hi_b:-11, lo_b:0 [ 3.578739] tegra-xusb 3530000.xhci: Direct firmware load for tegra18x_xusb_firmware failed with error -2 [ 3.578748] tegra-xusb 3530000.xhci: Falling back to user helper [ 3.580695] gpio tegra-gpio-aon wake35 for gpio=16(V:0) [ 3.582176] nct1008_nct72 7-004c: nct1008_probe: initialized [ 3.591204] usbcore: registered new interface driver uas [ 3.591849] usbcore: registered new interface driver usb-storage [ 3.592683] usbcore: registered new interface driver usbserial [ 3.639225] tegra-xudc-new 3550000.xudc: device count: 1 [ 3.647732] tegra-xudc-new 3550000.xudc: vbus state: 1 [ 3.987696] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 3.988499] ata1.00: ATA-10: FORESEE 64GB SSD, V4.6, max UDMA/133 [ 3.988518] ata1.00: 125045424 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 3.988979] ata1.00: configured for UDMA/133 [ 4.002848] scsi 0:0:0:0: Direct-Access ATA FORESEE 64GB SSD V4.6 PQ: 0 ANSI: 5 [ 4.043105] sd 0:0:0:0: [sda] 125045424 512-byte logical blocks: (64.0 GB/59.6 GiB) [ 4.044641] sd 0:0:0:0: [sda] Write Protect is off [ 4.044837] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.050496] sda: sda1 < sda5 > [ 4.054410] sd 0:0:0:0: [sda] Attached SCSI disk [ 4.137767] tegra-xusb-padctl 3520000.xusb_padctl: tegra186_xusb_padctl_utmi_pad_dcd: DCD timeout 418 ms [ 4.185086] tegra-usb-cd usb_cd: notification status (0x0, 0x1) [ 4.185102] tegra-usb-cd usb_cd: connected to SDP [ 4.185200] tegra-xudc-new 3550000.xudc: device mode on: 0 [ 4.186319] tegra-xudc-new 3550000.xudc: active: 0 => 1 [ 4.192458] mousedev: PS/2 mouse device common for all mice [ 4.193316] usbcore: registered new interface driver xpad [ 4.298872] tegradc 15210000.nvdisplay: unblank [ 4.304361] tegra_nvdisp_handle_pd_enable: Unpowergated Head0 pd [ 4.305001] tegra_nvdisp_handle_pd_enable: Unpowergated Head1 pd [ 4.305821] tegra_nvdisp_handle_pd_enable: Unpowergated Head2 pd [ 4.319190] Parent Clock set for DC plld2 [ 4.322540] tegradc 15210000.nvdisplay: hdmi: tmds rate:74250K prod-setting:prod_c_hdmi_54m_111m [ 4.323805] tegradc 15210000.nvdisplay: hdmi: get YCC quant from EDID. [ 4.327252] tegra-i2c 3190000.i2c: arb lost in communicate to add 0x50 [ 4.327383] tegra-i2c 3190000.i2c: Un-recovered Arb lost [ 4.331108] extcon-disp-state external-connection:disp-state: cable 47 state 1 [ 4.331109] Extcon AUX1(HDMI) enable [ 4.340590] tegradc 15210000.nvdisplay: sync windows ret = 247 [ 4.347926] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 4.349123] Wake73 for irq=42 [ 4.350368] rtc rtc1: alarm rtc device [ 4.350378] tegra_rtc c2a0000.rtc: rtc core: registered c2a0000.rtc as rtc1 [ 4.350392] tegra_rtc c2a0000.rtc: Tegra internal Real Time Clock [ 4.350596] i2c /dev entries driver [ 4.351832] ov9281 2-0060: probing v4l2 sensor. [ 4.351835] ov9281 2-0060: henry hello test debug tttttttt test2022. [ 4.351837] henry debug line1156 [ 4.351872] henry debug line1171 [ 4.351873] henry debug line1176 [ 4.351993] henry debug line1156 [ 4.351994] henry debug line1232 [ 4.362514] henry debug line1228 [ 4.362518] ov9281 2-0060: henry test on camera common init line999. [ 4.362555] extract_pixel_format: henry debug formatyuv_grey8 [ 4.362587] henry debug line1234 [ 4.362589] henry debug line1238 [ 4.362592] ov9281 2-0060: ov9281_ctrls_init++ [ 4.362609] henry debug line1243 [ 4.362610] henry debug new line1248 [ 4.364516] tegra-i2c 3180000.i2c: no acknowledge from address 0x60 [ 4.364546] ov9281 2-0060: Failed to read chip ID [ 4.364547] henry debug line1123 [ 4.364553] ov9281 2-0060: ov9281_power_off: power off [ 4.369977] tegra-i2c 3180000.i2c: no acknowledge from address 0x60 [ 4.370061] regmap_util_write_table_8:regmap_util_write_table:-121 [ 4.370061] ov9281: probe of 2-0060 failed with error -121 [ 4.378756] max77620-power max77620-power: Event recorder REG_NVERC : 0x0 [ 4.510529] parse_throttle_dt_data: Num cap clks = 4 [ 4.510532] parse_throttle_dt_data: clk=mcpu type=1 [ 4.510534] parse_throttle_dt_data: clk=bcpu type=2 [ 4.510540] parse_throttle_dt_data: clk=gpu type=4 [ 4.510542] parse_throttle_dt_data: clk=emc type=3 [ 4.582567] tegra_throttle_probe: probe successful. #cdevs=4 [ 4.583111] FAN: coudln't get the regulator [ 4.583654] tegra-oc-event d280000.soctherm-oc-event: OC driver initialized [ 4.584596] device-mapper: uevent: version 1.0.3 [ 4.584982] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 4.585256] CPU EMC frequency mapping table: from device tree [ 4.705980] cpufreq: platform driver Initialization: pass [ 4.711235] cpuidle: Initializing cpuidle driver init for Denver cluster [ 4.711355] cpuidle: Initializing cpuidle driver init for A57 cluster [ 4.717531] sdhci: Secure Digital Host Controller Interface driver [ 4.717532] sdhci: Copyright(c) Pierre Ossman [ 4.717533] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.773973] sdhci-tegra 3460000.sdhci: Client registration for eMC Successful [ 4.831532] CMDQ: cmdq_platfm_init successful [ 4.850522] CQE: CMD_TIMING bit set for R1B DCMD [ 4.863610] sdhci-tegra 3440000.sdhci: Client registration for eMC Successful [ 4.915533] mmc0: SDHCI controller on 3460000.sdhci [3460000.sdhci] using ADMA 64-bit with 64 bit addr [ 4.920209] sdhci-tegra 3400000.sdhci: Got CD GPIO [ 4.920259] sdhci-tegra 3400000.sdhci: Got WP GPIO [ 4.945254] sdhci-tegra 3400000.sdhci: Client registration for eMC Successful [ 4.963533] mmc1: SDHCI controller on 3440000.sdhci [3440000.sdhci] using ADMA 64-bit with 64 bit addr [ 4.997004] sdhci-tegra 3400000.sdhci: wakeup init done, cdirq 258 [ 5.055573] gpio tegra-gpio wake71 for gpio=125(P:5) [ 5.055617] mmc2: SDHCI controller on 3400000.sdhci [3400000.sdhci] using ADMA 64-bit with 64 bit addr [ 5.063947] tegra-se-nvhost 15810000.se: initialized [ 5.083176] mmc0: mmc_decode_ext_csd: CMDQ supported: depth: 31, cmdq_support: 1 [ 5.090275] tegra-se-nvhost 15810000.se: tegra_se_probe: complete [ 5.146874] tegra-se-nvhost 15820000.se: initialized [ 5.147978] tegra-se-nvhost 15820000.se: tegra_se_probe: complete [ 5.196533] tegra-se-nvhost 15830000.se: initialized [ 5.197436] tegra-se-nvhost 15830000.se: tegra_se_probe: complete [ 5.221017] tegra-se-nvhost 15840000.se: initialized [ 5.222017] tegra-se-nvhost 15840000.se: tegra_se_probe: complete [ 5.261636] tegra-se-elp 3ad0000.se_elp: tegra_se_elp_probe: complete [ 5.261776] hidraw: raw HID events driver (C) Jiri Kosina [ 5.262612] usbcore: registered new interface driver usbhid [ 5.262613] usbhid: USB HID core driver [ 5.296217] mmc0: periodic cache flush enabled [ 5.296224] mmc0: new HS400 Enhanced strobe MMC card at address 0001 [ 5.300505] mmcblk0: mmc0:0001 DG4032 29.1 GiB [ 5.300596] mmcblk0boot0: mmc0:0001 DG4032 partition 1 4.00 MiB [ 5.304697] mmcblk0boot1: mmc0:0001 DG4032 partition 2 4.00 MiB [ 5.308786] mmcblk0rpmb: mmc0:0001 DG4032 partition 3 4.00 MiB [ 5.387086] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 p29 p30 p31 p32 p33 [ 5.395303] tegra186-cam-rtcpu b000000.rtcpu: Trace buffer configured at IOVA=0xbff00000 [ 5.592481] tegra-ivc ivc-b000000.rtcpu: region 0: iova=0xbfef0000-0xbfefdb7f size=56192 [ 5.592740] tegra-ivc ivc-b000000.rtcpu:echo@0: echo: ver=0 grp=1 RX[16x64]=0x1000-0x1480 TX[16x64]=0x1480-0x1900 [ 5.592867] tegra-ivc ivc-b000000.rtcpu:i2c@480: i2c: ver=0 grp=1 RX[8x128]=0x1900-0x1d80 TX[8x128]=0x1d80-0x2200 [ 5.593059] tegra-ivc ivc-b000000.rtcpu:vinotify@12c0: vinotify: ver=0 grp=1 RX[64x128]=0x2200-0x4280 TX[64x128]=0x4280-0x6300 [ 5.593918] tegra-ivc ivc-b000000.rtcpu:mods@32c0: mods: ver=0 grp=1 RX[1x64]=0x6300-0x63c0 TX[1x64]=0x63c0-0x6480 [ 5.593989] tegra-ivc ivc-b000000.rtcpu:ivccontrol@52c0: ivccontrol: ver=0 grp=1 RX[16x320]=0x6480-0x7900 TX[16x320]=0x7900-0x8d80 [ 5.594038] tegra-ivc ivc-b000000.rtcpu:ivccapture@72c0: ivccapture: ver=0 grp=1 RX[16x64]=0x8d80-0x9200 TX[16x64]=0x9200-0x9680 [ 5.594084] tegra-ivc ivc-b000000.rtcpu:dbg@7c00: dbg: ver=0 grp=1 RX[1x384]=0x9680-0x9880 TX[1x384]=0x9880-0x9a80 [ 5.594228] tegra-ivc ivc-b000000.rtcpu:dbg@7e00: dbg: ver=0 grp=1 RX[1x8192]=0x9a80-0xbb00 TX[1x8192]=0xbb00-0xdb80 [ 5.594552] tegra186-cam-rtcpu b000000.rtcpu: using cam RTCPU IRQ (52) [ 5.594554] tegra186-cam-rtcpu b000000.rtcpu: tegra_camrtc_mon_create is successful [ 5.675931] tegra186-cam-rtcpu b000000.rtcpu: firmware version cpu=sce cmd=5 sha1=c73bbe92930645be44530c166eb578bfbb9499c3 [ 5.677652] tegra_aon c1a0000.aon: tegra aon driver probe OK [ 5.678074] tegra186-aondbg aondbg: aondbg driver probe() OK [ 5.678439] register_ari_mca_banks: Registered MCA ROC:IOB [ 5.678722] register_ari_mca_banks: Registered MCA ROC:CCE [ 5.679411] tegra18-bridge 2390000.axi2apb: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 5.679413] tegra18-bridge 2390000.axi2apb: enabled timeout = 11155000 [ 5.679415] tegra18-bridge 2390000.axi2apb: bridge probed OK [ 5.679464] tegra18-bridge 23a0000.axi2apb: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 5.679466] tegra18-bridge 23a0000.axi2apb: enabled timeout = 11155000 [ 5.679468] tegra18-bridge 23a0000.axi2apb: bridge probed OK [ 5.679514] tegra18-bridge 23b0000.axi2apb: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 5.679535] tegra18-bridge 23b0000.axi2apb: enabled timeout = 11155000 [ 5.679536] tegra18-bridge 23b0000.axi2apb: bridge probed OK [ 5.679589] tegra18-bridge 23c0000.axi2apb: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 5.679591] tegra18-bridge 23c0000.axi2apb: enabled timeout = 11155000 [ 5.679592] tegra18-bridge 23c0000.axi2apb: bridge probed OK [ 5.679644] tegra18-bridge 23d0000.axi2apb: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 5.679646] tegra18-bridge 23d0000.axi2apb: enabled timeout = 11155000 [ 5.679647] tegra18-bridge 23d0000.axi2apb: bridge probed OK [ 5.679694] tegra18-bridge 2100000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 5.679698] tegra18-bridge 2100000.axip2p: enabled timeout = 11155000 [ 5.679699] tegra18-bridge 2100000.axip2p: bridge probed OK [ 5.679746] tegra18-bridge 2110000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 5.679750] tegra18-bridge 2110000.axip2p: enabled timeout = 11155000 [ 5.679751] tegra18-bridge 2110000.axip2p: bridge probed OK [ 5.679799] tegra18-bridge 2120000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 5.679803] tegra18-bridge 2120000.axip2p: enabled timeout = 11155000 [ 5.679805] tegra18-bridge 2120000.axip2p: bridge probed OK [ 5.679852] tegra18-bridge 2130000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 5.679856] tegra18-bridge 2130000.axip2p: enabled timeout = 11155000 [ 5.679857] tegra18-bridge 2130000.axip2p: bridge probed OK [ 5.679903] tegra18-bridge 2140000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 5.679905] tegra18-bridge 2140000.axip2p: enabled timeout = 11155000 [ 5.679906] tegra18-bridge 2140000.axip2p: bridge probed OK [ 5.679954] tegra18-bridge 2150000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 5.679959] tegra18-bridge 2150000.axip2p: enabled timeout = 11155000 [ 5.679960] tegra18-bridge 2150000.axip2p: bridge probed OK [ 5.680006] tegra18-bridge 2160000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 5.680011] tegra18-bridge 2160000.axip2p: enabled timeout = 11155000 [ 5.680012] tegra18-bridge 2160000.axip2p: bridge probed OK [ 5.680062] tegra18-bridge 2170000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 5.680066] tegra18-bridge 2170000.axip2p: enabled timeout = 11155000 [ 5.680067] tegra18-bridge 2170000.axip2p: bridge probed OK [ 5.680123] tegra18-bridge 2180000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 5.680128] tegra18-bridge 2180000.axip2p: enabled timeout = 11155000 [ 5.680129] tegra18-bridge 2180000.axip2p: bridge probed OK [ 5.680176] tegra18-bridge 2190000.axip2p: axi_cbb clk rate = 115 MHZ, timeout = 97000 useconds [ 5.680179] tegra18-bridge 2190000.axip2p: enabled timeout = 11155000 [ 5.680181] tegra18-bridge 2190000.axip2p: bridge probed OK [ 5.680233] **** A57 ECC: Enabled [ 5.680234] tegra18_a57_serr_init: on CPU 3 a A57 Core [ 5.680292] tegra18x_actmon d230000.actmon: in actmon_register()... [ 5.722895] tegra18x_actmon d230000.actmon: initialization Completed for the device mc_all [ 5.723324] hw perfevents: enabled with denver15_uncore_pmu PMU driver, 3 counters available [ 5.723439] denver_knobs_init:MTS_VERSION:53679346 [ 5.725277] nvpmodel: initialized successfully [ 5.736224] trusty-virtio trusty:virtio: initializing [ 5.736324] trusty_ipc virtio0: vring0: va(pa) ffffffc1e6062000(0) qsz 32 notifyid 1 [ 5.736330] trusty_ipc virtio0: vring1: va(pa) ffffffc1e6064000(0) qsz 32 notifyid 2 [ 5.736392] trusty-virtio trusty:virtio: initializing done [ 5.736485] trusty_ipc virtio0: is online [ 5.737711] usbcore: registered new interface driver snd-usb-audio [ 5.738566] tlv320aic32x4 1-0018: henry debug aic3204 enter [ 5.738567] henry debug aic3204 parse enter [ 5.738569] henry debug aic3204 parse leave [ 5.738571] tlv320aic32x4 1-0018: henry debug aic3204 line972 [ 5.738576] tlv320aic32x4 1-0018: henry debug aic3204 leave [ 6.308178] extcon-disp-state external-connection:disp-state: cable 51 state 1 [ 6.316329] Extcon HDMI: HPD enabled [ 6.320826] tegradc 15210000.nvdisplay: hdmi: plugged [ 6.332279] input: tegra-hda HDMI/DP,pcm=3 as /devices/3510000.hda/sound/card0/input0 [ 6.341203] input: tegra-hda HDMI/DP,pcm=7 as /devices/3510000.hda/sound/card0/input1 [ 6.347055] OPE platform probe [ 6.347118] OPE platform probe successful [ 6.388997] henry debug aic3204 codec probe enter!!!!!!!!!!!!! [ 6.399042] henry debug aic3204 codec probe leave!!!!!!!!!!!!! [ 6.423710] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok [ 6.430456] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok [ 6.437131] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok [ 6.443840] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok [ 6.450495] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok [ 6.457170] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok [ 6.463793] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok [ 6.470400] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok [ 6.477022] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok [ 6.477089] mmc1: Applying tuning correction [ 6.477101] mmc1: Tap value after applying correction 59 [ 6.477107] mmc1: hw tuning done ... [ 6.480872] mmc1: new ultra high speed SDR104 SDIO card at address 0001 [ 6.506482] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok [ 6.513288] tegra-asoc: sound: ADMAIF11 <-> ADMAIF11 mapping ok [ 6.520046] tegra-asoc: sound: ADMAIF12 <-> ADMAIF12 mapping ok [ 6.526811] tegra-asoc: sound: ADMAIF13 <-> ADMAIF13 mapping ok [ 6.533538] tegra-asoc: sound: ADMAIF14 <-> ADMAIF14 mapping ok [ 6.540250] tegra-asoc: sound: ADMAIF15 <-> ADMAIF15 mapping ok [ 6.547000] tegra-asoc: sound: ADMAIF16 <-> ADMAIF16 mapping ok [ 6.553693] tegra-asoc: sound: ADMAIF17 <-> ADMAIF17 mapping ok [ 6.560405] tegra-asoc: sound: ADMAIF18 <-> ADMAIF18 mapping ok [ 6.567039] tegra-asoc: sound: ADMAIF19 <-> ADMAIF19 mapping ok [ 6.573646] tegra-asoc: sound: ADMAIF20 <-> ADMAIF20 mapping ok [ 6.582748] tegra-asoc: sound: henry debug tlv320aic_init enter! [ 6.589401] tegra-asoc: sound: henry debug tlv320aic_init leave! [ 6.619167] u32 classifier [ 6.622527] Actions configured [ 6.626643] Initializing XFRM netlink socket [ 6.632060] NET: Registered protocol family 10 [ 6.637663] NET: Registered protocol family 17 [ 6.642681] NET: Registered protocol family 15 [ 6.647711] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 6.661313] Bluetooth: RFCOMM socket layer initialized [ 6.667072] Bluetooth: RFCOMM ver 1.11 [ 6.671444] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 6.678005] Bluetooth: HIDP socket layer initialized [ 6.683592] 9pnet: Installing 9P2000 support [ 6.688518] Key type dns_resolver registered [ 6.693605] Registered cp15_barrier emulation handler [ 6.699292] Registered setend emulation handler [ 6.705294] registered taskstats version 1 [ 6.713493] isp 15600000.isp: initialized [ 6.722635] nvcsi 150c0000.nvcsi: initialized [ 6.729408] tegra-vi4 15700000.vi: using default number of vi channels,15 [ 6.733688] Wake83 for irq=51 [ 6.733760] gpio tegra-gpio-aon wake29 for gpio=56(FF:0) [ 6.733839] gpio tegra-gpio-aon wake67 for gpio=57(FF:1) [ 6.733912] gpio tegra-gpio-aon wake68 for gpio=58(FF:2) [ 6.734040] input: gpio-keys as /devices/gpio-keys/input/input2 [ 6.767720] tegra-vi4 15700000.vi: initialized [ 6.772878] tegra_rtc c2a0000.rtc: setting system clock to 2000-01-01 18:09:37 UTC (946750177) [ 6.774275] mmcblk mmc0:0001: Card claimed for testing. [ 6.789436] tegra-vi4 15700000.vi: subdev 150c0000.nvcsi--1 bound [ 6.802581] bpmp: mounted debugfs mirror [ 6.808550] bwmgr: missing cdev-type property [ 6.818464] ALSA device list: [ 6.822194] #0: tegra-hda at 0x3518000 irq 384 [ 6.827589] #1: tegra-snd-t186ref-mobile-rt565x [ 6.838978] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 6.847918] VFS: Mounted root (ext4 filesystem) on device 179:1. [ 6.857158] devtmpfs: mounted [ 6.863194] Freeing unused kernel memory: 8448K [ 7.011620] systemd[1]: System time before build time, advancing clock. [ 7.056386] ip_tables: (C) 2000-2006 Netfilter Core Team [ 7.071387] cgroup: cgroup2: unknown option "nsdelegate" [ 7.101913] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 ) [ 7.133537] systemd[1]: Detected architecture arm64. [ 7.160965] systemd[1]: Set hostname to . [ 7.277976] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 7.297390] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 7.455351] random: systemd: uninitialized urandom read (16 bytes read) [ 7.464562] systemd[1]: Created slice User and Session Slice. [ 7.473232] random: systemd: uninitialized urandom read (16 bytes read) [ 7.482124] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 7.494198] random: systemd: uninitialized urandom read (16 bytes read) [ 7.502166] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 7.512474] systemd[1]: Reached target Swap. [ 7.520159] systemd[1]: Created slice System Slice. [ 7.625255] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null) [ 7.800067] systemd-journald[2219]: Received request to flush runtime journal from PID 1 [ 7.867217] random: crng init done [ 7.871521] random: 7 urandom warning(s) missed due to ratelimiting [ 10.653313] using random self ethernet address [ 10.667607] using random host ethernet address [ 11.374270] using random self ethernet address [ 11.386578] using random host ethernet address [ 11.645611] CPU1: shutdown [ 11.700871] CPU2: shutdown [ 12.730858] Bridge firewalling registered Ubuntu 18.04.5 LTS t-desktop ttyS0 [END] 2022/6/28 11:30:22