user@user-ubuntu:~$ sudo minicom [sudo] password for user: Welcome to minicom 2.7.1 OPTIONS: I18n Compiled on Aug 13 2017, 15:25:34. Port /dev/ttyUSB0, 09:05:49 Press CTRL-A Z for help on special keys [0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-dd84d362) [0000.130] Processing in cold boot mode Bootloader 2 [0000.135] A02 Bootrom Patch rev = 1023 [0000.138] Power-up reason: pmc por [0000.141] No Battery Present [0000.144] pmic max77620 reset reason [0000.147] pmic max77620 NVERC : 0x40 [0000.151] RamCode = 0 [0000.153] Platform has DDR4 type RAM [0000.156] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0x903ec [0000.172] Entering ramdump check [0000.175] Get RamDumpCarveOut = 0x0 [0000.178] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.188] Sdram initialization is successful [0000.192] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.198] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.204] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.210] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.233] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.256] Platform-DebugCarveout: 0 [0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.265] Non secure mode, and RB not enabled. [0000.269] BoardID = 3448, SKU = 0x0 [0000.272] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.276] Nano-SD: checking PT table on QSPI ... [0000.280] Read PT from (2:0) [0000.296] Using BFS PT to query partitions [0000.301] Loading Tboot-CPU binary [0000.330] Verifying TBC in OdmNonSecureSBK mode [0000.340] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.347] Bootloader downloaded successfully. [0000.351] Downloaded Tboot-CPU binary to 0xa0000258 [0000.356] MAX77620_GPIO5 configured [0000.359] CPU power rail is up [0000.362] CPU clock enabled [0000.366] Performing RAM repair [0000.369] Updating A64 Warmreset Address to 0xa00002e9 [0000.374] BoardID = 3448, SKU = 0x0 [0000.377] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.381] Nano-SD: checking PT table on QSPI ... [0000.385] Loading NvTbootBootloaderDTB [0000.452] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.525] Bootloader DTB Load Address: 0x83000000 [0000.530] BoardID = 3448, SKU = 0x0 [0000.533] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.537] Nano-SD: checking PT table on QSPI ... [0000.541] Loading NvTbootKernelDTB [0000.607] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.680] Kernel DTB Load Address: 0x83100000 [0000.684] BoardID = 3448, SKU = 0x0 [0000.688] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.691] Nano-SD: checking PT table on QSPI ... [0000.698] Loading cboot binary [0000.813] Verifying EBT in OdmNonSecureSBK mode [0000.855] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.862] Bootloader downloaded successfully. [0000.866] BoardID = 3448, SKU = 0x0 [0000.870] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.873] Nano-SD: checking PT table on QSPI ... [0000.878] PT: Partition NCT NOT found ! [0000.882] Warning: Find Partition via PT Failed [0000.886] Next binary entry address: 0x92c00258 [0000.891] BoardId: 3448 [0000.895] Overriding pmu board id with proc board id [0000.900] Display board id is not available [0000.904] BoardID = 3448, SKU = 0x0 [0000.907] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.911] Nano-SD: checking PT table on QSPI ... [0001.016] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.073] /bpmp deleted [0001.075] SC7EntryFw header found loaded at 0xff700000 [0001.271] OVR2 PMIC [0001.272] Bpmp FW successfully loaded [0001.276] BoardID = 3448, SKU = 0x0 [0001.279] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.283] Nano-SD: checking PT table on QSPI ... [0001.288] WB0 init successfully at 0xff780000 [0001.293] Set NvDecSticky Bits [0001.296] GSC2 address ff53fffc value c0edbbcc [0001.302] GSC MC Settings done [0001.305] BoardID = 3448, SKU = 0x0 [0001.309] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.312] Nano-SD: checking PT table on QSPI ... [0001.318] TOS Image length 53680 [0001.321] Monitor size 53680 [0001.324] OS size 0 [0001.339] Secure Os AES-CMAC Verification Success! [0001.343] TOS image cipher info: plaintext [0001.347] Loading and Validation of Secure OS Successful [0001.363] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.368] NvTbootPackSdramParams: start. [0001.373] NvTbootPackSdramParams: done. [0001.377] Tegraboot started after 51828 us [0001.381] Basic modules init took 886385 us [0001.385] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB [0001.390] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.396] Next stage binary read took 102860 us [0001.400] Carveout took -126357 us [0001.403] CPU initialization took 495394 us [0001.407] Total time taken by TegraBoot 1358282 us [0001.412] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):5b49e7f80 NOTICE: BL31: Built : 08:53:41, Jul 9 2021 ERROR: Error initializing runtime service trusty_fast [0001.534] RamCode = 0 [0001.539] LPDDR4 Training: Read DT: Number of tables = 2 [0001.544] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.557] EMC Training Successful [0001.560] 408000 not found in DVFS table [0001.566] RamCode = 0 [0001.570] DT Write: emc-table@204000 succeeded [0001.575] DT Write: emc-table@1600000 succeeded [0001.579] LPDDR4 Training: Write DT: Number of tables = 2 [0001.626] [0001.627] Debug Init done [0001.630] Marked DTB cacheable [0001.633] Bootloader DTB loaded at 0x83000000 [0001.638] Marked DTB cacheable [0001.640] Kernel DTB loaded at 0x83100000 [0001.644] DeviceTree Init done [0001.657] Pinmux applied successfully [0001.662] gicd_base: 0x50041000 [0001.665] gicc_base: 0x50042000 [0001.668] Interrupts Init done [0001.672] Using base:0x60005090 & irq:208 for tick-timer [0001.677] Using base:0x60005098 for delay-timer [0001.682] platform_init_timer: DONE [0001.685] Timer(tick) Init done [0001.689] osc freq = 38400 khz [0001.693] [0001.694] Welcome to L4T Cboot [0001.697] [0001.698] Cboot Version: 00.00.2018.01-t210-39562017 [0001.703] calling constructors [0001.706] initializing heap [0001.709] initializing threads [0001.712] initializing timers [0001.715] creating bootstrap completion thread [0001.719] top of bootstrap2() [0001.722] CPU: ARM Cortex A57 [0001.725] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.729] initializing platform [0001.737] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.742] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.746] Macronix QSPI chip present [0001.750] SPI device register [0001.752] init boot device [0001.755] allocating memory for boot device(SPI) [0001.760] registering boot device [0001.768] QSPI bdev is already initialized [0001.772] Enable APE clock [0001.774] Un-powergate APE partition [0001.778] of_register: registering tegra_udc to of_hal [0001.783] of_register: registering inv20628-driver to of_hal [0001.789] of_register: registering ads1015-driver to of_hal [0001.794] of_register: registering lp8557-bl-driver to of_hal [0001.800] of_register: registering bq2419x_charger to of_hal [0001.806] of_register: registering bq27441_fuel_gauge to of_hal [0001.817] gpio framework initialized [0001.821] of_register: registering tca9539_gpio to of_hal [0001.826] of_register: registering tca9539_gpio to of_hal [0001.831] of_register: registering i2c_bus_driver to of_hal [0001.837] of_register: registering i2c_bus_driver to of_hal [0001.843] of_register: registering i2c_bus_driver to of_hal [0001.848] pmic framework initialized [0001.852] of_register: registering max77620_pmic to of_hal [0001.857] regulator framework initialized [0001.861] of_register: registering tps65132_bl_driver to of_hal [0001.867] initializing target [0001.873] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.881] board ID = D78, board SKU = 0 [0001.884] Skipping Z3! [0001.889] fixed regulator driver initialized [0001.907] initializing OF layer [0001.910] NCK carveout not present [0001.913] Skipping dts_overrides [0001.918] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.935] I2C Bus Init done [0001.937] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.948] I2C Bus Init done [0001.950] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.961] I2C Bus Init done [0001.963] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.974] I2C Bus Init done [0001.976] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0001.987] I2C Bus Init done [0001.989] of_children_init: Ops found for compatible string maxim,max77620 [0002.000] max77620_init using irq 118 [0002.005] register 'maxim,max77620' pmic [0002.009] gpio_driver_register: register 'max77620-gpio' driver [0002.015] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.026] I2C Bus Init done [0002.029] NCK carveout not present [0002.039] Find /i2c@7000c000's alias i2c0 [0002.043] get eeprom at 1-a0, size 256, type 0 [0002.052] Find /i2c@7000c500's alias i2c2 [0002.056] get eeprom at 3-a0, size 256, type 0 [0002.060] get eeprom at 3-ae, size 256, type 0 [0002.065] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.070] I2C slave not started [0002.073] I2C write failed [0002.075] Writing offset failed [0002.079] eeprom_init: EEPROM read failed [0002.082] pm_ids_update: eeprom init failed [0002.087] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.117] pm_ids_update: The pm board id is 3448-0000-402 [0002.123] Adding plugin-manager/ids/3448-0000-402=/i2c@7000c500:module@0x50 [0002.132] pm_ids_update: pm id update successful [0002.136] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.167] pm_ids_update: The pm board id is 3449-0000-400 [0002.173] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.181] pm_ids_update: pm id update successful [0002.211] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.217] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.225] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.231] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.239] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3c:b0:bb [0002.245] Plugin Manager: Parse ODM data 0x000a4000 [0002.258] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.273] Find /i2c@7000c000's alias i2c0 [0002.276] get eeprom at 1-a0, size 256, type 0 [0002.285] Find /i2c@7000c500's alias i2c2 [0002.289] get eeprom at 3-a0, size 256, type 0 [0002.294] get eeprom at 3-ae, size 256, type 0 [0002.298] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.303] I2C slave not started [0002.306] I2C write failed [0002.309] Writing offset failed [0002.312] eeprom_init: EEPROM read failed [0002.316] pm_ids_update: eeprom init failed [0002.320] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.350] pm_ids_update: The pm board id is 3448-0000-402 [0002.356] Adding plugin-manager/ids/3448-0000-402=/i2c@7000c500:module@0x50 [0002.363] pm_ids_update: pm id update successful [0002.368] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.398] pm_ids_update: The pm board id is 3449-0000-400 [0002.404] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.411] pm_ids_update: pm id update successful [0002.441] Add serial number:1420821029663 as DT property [0002.449] Applying platform configs [0002.456] platform-init is not present. Skipping [0002.460] calling apps_init() [0002.466] Couldn't find GPT header [0002.471] Proceeding to Cold Boot [0002.474] starting app android_boot_app [0002.478] Device state: unlocked [0002.481] display console init [0002.489] could not find regulator [0002.513] hdmi cable not connected [0002.516] is_hdmi_needed: HDMI not connected, returning false [0002.522] hdmi is not connected [0002.528] DT entry for leds-pwm not found [0002.532] sor0 is not supported [0002.535] display_console_init: no valid display out_type [0002.543] subnode volume_up is not found ! [0002.547] subnode back is not found ! [0002.551] subnode volume_down is not found ! [0002.555] subnode menu is not found ! [0002.558] Gpio keyboard init success [0002.639] found decompressor handler: lz4-legacy [0002.653] decompressing blob (type 1)... [0002.720] display_resolution: No display init [0002.724] Failed to retrieve display resolution [0002.728] Could not load/initialize BMP blob...ignoring [0002.803] decompressor handler not found [0002.807] load_firmware_blob: Firmware blob loaded, entries=2 [0002.813] XUSB blob version 0 size 124416 @ 0x92ca828c [0002.819] -------> se_aes_verify_sbk_clear: 747 [0002.823] se_aes_verify_sbk_clear: Error [0002.827] SE operation failed [0002.830] bl_battery_charging: connected to external power supply [0002.839] display_console_ioctl: No display init [0002.843] switch_backlight failed [0002.850] device_query_partition_size: failed to open partition spiflash0:MSC ! [0002.857] MSC Partition not found [0002.863] device_query_partition_size: failed to open partition spiflash0:USP ! [0002.871] USP partition read failed! [0002.874] blob_init: blob-partition USP header read failed [0002.880] android_boot Unable to update recovery partition [0002.885] kfs_getpartname: name = LNX [0002.889] Loading kernel from LNX [0002.898] Found 19 BFS partitions in "spiflash0" [0003.220] load kernel from storage [0003.225] decompressor handler not found [0003.493] Successfully loaded kernel and ramdisk images [0003.498] board ID = D78, board SKU = 0 [0003.503] sdmmc node status = okay [0003.506] sdcard instance = 0 [0003.509] sdcard gpio handle 0x5b [0003.512] sdcard gpio pin 0xc9 [0003.515] sdcard gpio flags 0x0 [0003.518] vmmc-supply 0x9e [0003.521] cd_gpio_pin = 201 [0003.524] pin_state = 1 [0003.526] No sdcard [0003.528] SD-card NOT present ... [0003.531] load_and_boot_kernel: SD card not detected! [0003.537] display_resolution: No display init [0003.541] Failed to retrieve display resolution [0003.546] bmp blob is not loaded and initialized [0003.550] SDcard warning bmp failed! [0003.555] display_resolution: No display init [0003.559] Failed to retrieve display resolution [0003.564] bmp blob is not loaded and initialized [0003.568] Failed to display boot-logo [0003.572] NCK carveout not present [0003.575] Skipping dts_overrides [0003.578] NCK carveout not present [0003.588] Find /i2c@7000c000's alias i2c0 [0003.592] get eeprom at 1-a0, size 256, type 0 [0003.601] Find /i2c@7000c500's alias i2c2 [0003.605] get eeprom at 3-a0, size 256, type 0 [0003.609] get eeprom at 3-ae, size 256, type 0 [0003.613] pm_ids_update: Updating 1,a0, size 256, type 0 [0003.619] I2C slave not started [0003.622] I2C write failed [0003.624] Writing offset failed [0003.627] eeprom_init: EEPROM read failed [0003.631] pm_ids_update: eeprom init failed [0003.635] pm_ids_update: Updating 3,a0, size 256, type 0 [0003.666] pm_ids_update: The pm board id is 3448-0000-402 [0003.672] Adding plugin-manager/ids/3448-0000-402=/i2c@7000c500:module@0x50 [0003.681] pm_ids_update: pm id update successful [0003.685] pm_ids_update: Updating 3,ae, size 256, type 0 [0003.715] pm_ids_update: The pm board id is 3449-0000-400 [0003.722] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0003.730] pm_ids_update: pm id update successful [0003.760] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0003.766] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0003.774] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0003.780] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0003.788] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:3c:b0:bb [0003.794] Plugin Manager: Parse ODM data 0x000a4000 [0003.807] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0003.815] Add serial number:1420821029663 as DT property [0003.824] "bpmp" doesn't exist, creating [0003.830] Updated bpmp info to DTB [0003.834] Updated initrd info to DTB [0003.838] "proc-board" doesn't exist, creating [0003.844] Updated board info to DTB [0003.847] "pmu-board" doesn't exist, creating [0003.853] Updated board info to DTB [0003.857] "display-board" doesn't exist, creating [0003.863] Updated board info to DTB [0003.866] "reset" doesn't exist, creating [0003.871] Updated reset info to DTB [0003.874] display_console_ioctl: No display init [0003.878] display_console_ioctl: No display init [0003.883] display_console_ioctl: No display init [0003.888] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0 [0003.922] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0003.928] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0003.941] Updated bootarg info to DTB [0003.945] Adding uuid 00000001642e12c30c0000000d010580 to DT [0003.951] Adding eks info 0 to DT [0003.956] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0003.962] Updated memory info to DTB [0003.970] set vdd_core voltage to 1125 mv [0003.974] setting 'vdd-core' regulator to 1125000 micro volts [0003.980] Found secure-pmc; disable BPMP U-Boot 2020.04-g6b630d64fd (Jul 09 2021 - 08:53:46 -0700) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 MMC: no card present Card did not respond to voltage select! starting USB... Bus usb@7d000000: tegrausb: Invalid dr_mode 2 for host mode probe failed, error -1 Bus xusb@70090000: Firmware size 124416 Firmware timestamp: 0x5da88fc3, Version: 50.25 release Register HCSParams1: 9000124 NbrPorts: 9 Starting the controller USB XHCI 1.00 scanning bus xusb@70090000 for devices... 6 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: Samsung Rev: 1100 Prod: Flash Drive FIT Type: Removable Hard Disk Capacity: 244752.5 MB = 239.0 GB (501253132 x 512) ... is now current device Scanning usb 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 828 bytes read in 2 ms (404.3 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 7159329 bytes read in 31 ms (220.2 MiB/s) Retrieving file: /boot/arducam/Image 34404360 bytes read in 140 ms (234.4 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 co Retrieving file: /boot/arducam/dts/tegra210-p3448-0000-p3449-0000-b00-imx477.dtb 239768 bytes read in 5 ms (45.7 MiB/s) ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000083000000, end 000000008303d897 copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... DT property /chosen/nvidia,bluetooth-mac missing in source; can't copy DT property /chosen/nvidia,wifi-mac missing in source; can't copy DT property /psci/nvidia,system-lp0-disable missing in source; can't copy Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.201-tegra (jenkins@feaf98b9a84d) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Fri Oct 15 02:34:21 UTC 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57560 r8192 d32552 u98304 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29480(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3568524K/4159488K available (15294K kernel code, 2942K rwdata, 6724K rodata, 8576K init, 609K bss, 115828K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f70000 ( 15296 KB) [ 0.000000] .rodata : 0xffffff8008f70000 - 0xffffff8009610000 ( 6784 KB) [ 0.000000] .init : 0xffffff8009610000 - 0xffffff8009e70000 ( 8576 KB) [ 0.000000] .data : 0xffffff8009e70000 - 0xffffff800a14f808 ( 2943 KB) [ 0.000000] .bss : 0xffffff800a14f808 - 0xffffff800a1e7cbc ( 610 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] PLL_RE already enabled. Postponing set full defaults [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.009954] Console: colour dummy device 80x25 [ 0.014602] console [tty0] enabled [ 0.018111] bootconsole [uart8250] disabled [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.201-tegra (jenkins@feaf98b9a84d) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Fri Oct 15 02:34:21 UTC 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57560 r8192 d32552 u98304 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544 [ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 131072 bytes [ 0.000000] early log buf free: 29480(89%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3568524K/4159488K available (15294K kernel code, 2942K rwdata, 6724K rodata, 8576K init, 609K bss, 115828K reserved, 475136K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f70000 ( 15296 KB) [ 0.000000] .rodata : 0xffffff8008f70000 - 0xffffff8009610000 ( 6784 KB) [ 0.000000] .init : 0xffffff8009610000 - 0xffffff8009e70000 ( 8576 KB) [ 0.000000] .data : 0xffffff8009e70000 - 0xffffff800a14f808 ( 2943 KB) [ 0.000000] .bss : 0xffffff800a14f808 - 0xffffff800a1e7cbc ( 610 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] t210 clock and reset probe [ 0.000000] PLL_RE already enabled. Postponing set full defaults [ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1 [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.009954] Console: colour dummy device 80x25 [ 0.014602] console [tty0] enabled [ 0.018111] bootconsole [uart8250] disabled [ 0.022440] kmemleak: Kernel memory leak detector disabled [ 0.022468] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.022489] pid_max: default: 32768 minimum: 301 [ 0.022952] Security Framework initialized [ 0.023174] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.023188] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.024297] ftrace: allocating 47233 entries in 185 pages [ 0.193263] ASID allocator initialised with 65536 entries [ 0.231949] tegra-id: chipid=22117. [ 0.231976] tegra-id: opt_subrevision=0. [ 0.231998] Tegra Speedo/IDDQ fuse revision 4 [ 0.232007] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2 [ 0.232018] Tegra: CPU Process ID 0, SoC Process ID 0, GPU Process ID 0 [ 0.232029] Tegra: CPU Speedo Value 2020, SoC Speedo Value 1907, GPU Speedo Value 2024 [ 0.232040] Tegra: CPU IDDQ Value 1760, SoC IDDQ Value 2000, GPU IDDQ Value 2380 [ 0.232064] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 0 [ 0.232087] DTS File Name: /var/jenkins_home/workspace/n_nano_kernel_l4t-32.5.2-arducam/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-b00-imx477.dts [ 0.232110] DTB Build time: Oct 15 2021 02:34:56 [ 0.281307] CPU1: Booted secondary processor [411fd071] [ 0.313192] CPU2: Booted secondary processor [411fd071] [ 0.345174] CPU3: Booted secondary processor [411fd071] [ 0.345272] Brought up 4 CPUs [ 0.345324] SMP: Total of 4 processors activated. [ 0.345341] CPU features: detected feature: 32-bit EL0 Support [ 0.345619] CPU: All CPU(s) started at EL2 [ 0.345645] alternatives: patching kernel code [ 0.353763] devtmpfs: initialized [ 0.391547] Initilizing CustomIPI irq domain [ 0.391963] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.392009] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.402505] pinctrl core: initialized pinctrl subsystem [ 0.403122] OS set in device tree is not L4T. [ 0.403548] regulator-dummy: no parameters [ 0.403832] Initializing plugin-manager [ 0.403997] Plugin module not found [ 0.404196] node /plugin-manager/fragement@0 match with board >=3448-0000-100 [ 0.404730] node /plugin-manager/fragment@1 match with board >=3448-0000-101 [ 0.405770] node /plugin-manager/fragement@7 match with odm-data enable-pmic-wdt [ 0.406014] node /plugin-manager/fragement@8 match with odm-data enable-pmic-wdt [ 0.406614] node /plugin-manager/fragement@10 match with board >=3448-0000-300 [ 0.408545] node /plugin-manager/fragement@13 match with board >=3448-0000-300 [ 0.412158] NET: Registered protocol family 16 [ 0.415680] pstore: using zlib compression [ 0.416182] console [pstore-1] enabled [ 0.416197] pstore: Registered ramoops as persistent store backend [ 0.416215] ramoops: attached 0x200000@0xb0000000, ecc: 0/0 [ 0.429317] cpuidle: using governor menu [ 0.432666] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver [ 0.434412] vdso: 2 pages (1 code @ ffffff8008f77000, 1 data @ ffffff8009e74000) [ 0.434455] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.437726] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations [ 0.440166] Serial: AMBA PL011 UART driver [ 0.440665] tegra_powergate_init: DONE [ 0.440697] DTS File Name: /var/jenkins_home/workspace/n_nano_kernel_l4t-32.5.2-arducam/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-b00-imx477.dts [ 0.440735] DTB Build time: Oct 15 2021 02:34:56 [ 0.442661] Tegra reboot handler registered. [ 0.447116] iommu: Adding device tegra-carveouts to group 0 [ 0.447289] platform tegra-carveouts: domain=ffffffc0f9bdb3d8 allocates as[0]=ffffffc0f94400a8 [ 0.447675] iommu: Adding device smmu_test to group 1 [ 0.447737] platform smmu_test: domain=ffffffc0f9bdb618 allocates as[0]=ffffffc0f9440110 [ 0.448565] mc: mapped MMIO address: 0xffffff800802e000 -> 0x70019000 [ 0.448640] mc: mapped MMIO address: 0xffffff8008065000 -> 0x7001c000 [ 0.448711] mc: mapped MMIO address: 0xffffff8008079000 -> 0x7001d000 [ 0.448732] nv-tegra-mc 70019000.mc: No mssnvlink node [ 0.448767] mc-err: mcerr ops are set to t21x [ 0.459277] iommu: Adding device 70090000.xusb to group 2 [ 0.459578] iommu: Adding device 70006000.serial to group 3 [ 0.459670] platform 70006000.serial: domain=ffffffc0f94d76d8 allocates as[0]=ffffffc0f9440178 [ 0.460110] iommu: Adding device 70006040.serial to group 4 [ 0.460391] iommu: Adding device 70006200.serial to group 5 [ 0.460641] iommu: Adding device sound to group 6 [ 0.460705] platform sound: domain=ffffffc0f94d7c18 allocates as[0]=ffffffc0f94401e0 [ 0.461317] iommu: Adding device 7000d400.spi to group 7 [ 0.461598] iommu: Adding device 7000d600.spi to group 8 [ 0.461888] iommu: Adding device 70410000.spi to group 9 [ 0.462201] iommu: Adding device 50000000.host1x to group 10 [ 0.462491] iommu: Adding device 54080000.vi to group 11 [ 0.462890] iommu: Adding device 54600000.isp to group 12 [ 0.463164] iommu: Adding device 54680000.isp to group 13 [ 0.463485] iommu: Adding device tegradc.0 to group 14 [ 0.463551] platform tegradc.0: domain=ffffffc0f94f4b58 allocates as[0]=ffffffc0f9440248 [ 0.464086] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000) [ 0.464410] iommu: Adding device tegradc.1 to group 15 [ 0.464474] platform tegradc.1: domain=ffffffc0f94f4d98 allocates as[0]=ffffffc0f94402b0 [ 0.465000] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000) [ 0.465291] iommu: Adding device 54340000.vic to group 16 [ 0.465527] iommu: Adding device 544c0000.nvenc to group 17 [ 0.465746] iommu: Adding device 54500000.tsec to group 18 [ 0.465961] iommu: Adding device 54100000.tsecb to group 19 [ 0.466175] iommu: Adding device 54480000.nvdec to group 20 [ 0.466402] iommu: Adding device 54380000.nvjpg to group 21 [ 0.467468] iommu: Adding device 546c0000.i2c to group 22 [ 0.467814] iommu: Adding device 57000000.gpu to group 23 [ 0.467877] platform 57000000.gpu: domain=ffffffc0f94ffd98 allocates as[0]=ffffffc0f9440318 [ 0.467931] platform 57000000.gpu: domain=ffffffc0f94ffd98 allocates as[1]=ffffffc0f9440380 [ 0.467988] platform 57000000.gpu: domain=ffffffc0f94ffd98 allocates as[2]=ffffffc0f94403e8 [ 0.468041] platform 57000000.gpu: domain=ffffffc0f94ffd98 allocates as[3]=ffffffc0f9440450 [ 0.468949] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.468986] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present [ 0.469013] tegra-pmc: ### PMC reset source: TEGRA_POWER_ON_RESET [ 0.469031] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM [ 0.469047] tegra-pmc: ### PMC reset status reg: 0x0 [ 0.521368] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [ 0.521401] tegra-pmc: Clear bootloader IO dpd settings [ 0.521433] tegra-pmc 7000e400.pmc: IO padctrl driver initialized [ 0.521510] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands [ 0.521815] iommu: Adding device 70012000.se to group 24 [ 0.522590] iommu: Adding device 7000c000.i2c to group 25 [ 0.522854] iommu: Adding device 7000c400.i2c to group 26 [ 0.523125] iommu: Adding device 7000c500.i2c to group 27 [ 0.523393] iommu: Adding device 7000c700.i2c to group 28 [ 0.523696] iommu: Adding device 7000d000.i2c to group 29 [ 0.523965] iommu: Adding device 7000d100.i2c to group 30 [ 0.524257] iommu: Adding device sdhci-tegra.0 to group 31 [ 0.524322] platform sdhci-tegra.0: domain=ffffffc0f959ef18 allocates as[0]=ffffffc0f94404b8 [ 0.525167] iommu: Adding device 700d0000.xudc to group 32 [ 0.528376] vdd-ac-bat: 5000 mV [ 0.528755] vdd-5v0-sys: 5000 mV [ 0.529746] vdd-5v0-hdmi: supplied by vdd-5v0-sys [ 0.529826] vdd-5v0-hdmi: 5000 mV [ 0.530246] vdd-1v8-sys: 1800 mV [ 0.530642] vdd-fan: supplied by vdd-5v0-sys [ 0.530698] vdd-fan: 5000 mV [ 0.531097] vdd-usb-vbus: supplied by vdd-5v0-sys [ 0.531167] vdd-usb-vbus: 5000 mV [ 0.531701] vdd-usb-vbus2: 5000 mV [ 0.566289] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.568760] gpio gpiochip0: gpio-line-names specifies 240 line names but there are 256 lines on the chip [ 0.570074] GPIO line 151 (camera-control-output-low) hogged as output/low [ 0.570109] GPIO line 152 (camera-control-output-low) hogged as output/low [ 0.570160] GPIO line 6 (system-suspend-gpio) hogged as output/high [ 0.570506] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio) [ 0.578345] eventlib_kernel: keventlib is initialized, test id: 0 [ 0.578747] SCSI subsystem initialized [ 0.579301] usbcore: registered new interface driver usbfs [ 0.579373] usbcore: registered new interface driver hub [ 0.579461] usbcore: registered new device driver usb [ 0.583363] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.588469] random: fast init done [ 0.589305] vdd-core: 600 <--> 1162 mV at 1125 mV [ 0.590370] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV [ 0.593245] vdd-ddr-1v1: 1150 mV [ 0.597195] vdd-pre-reg-1v35: 1350 mV [ 0.601189] vdd-1v8: 1800 mV [ 0.605192] avdd-sys-1v2: 1200 mV [ 0.609193] vdd-pex-1v0: 1050 mV [ 0.609860] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV [ 0.610417] max77620-ldo3: at 3100 mV [ 0.613194] vdd-rtc: 850 <--> 1100 mV at 1000 mV [ 0.613746] max77620-ldo5: at 3100 mV [ 0.617194] vddio-sdmmc3-ap: 1800 <--> 3300 mV at 2800 mV [ 0.621190] avdd-1v05-pll: 1050 mV [ 0.625188] avdd-io-hdmi-dp: 1050 mV [ 0.627812] GPIO line 505 (spmic-default-output-high) hogged as output/high [ 0.628104] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio) [ 0.628412] max77620 4-003c: max77620 probe successful [ 0.631076] media: Linux media interface: v0.10 [ 0.631154] Linux video capture interface: v2.00 [ 0.632057] pps_core: LinuxPPS API ver. 1 registered [ 0.632084] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.632124] PTP clock support registered [ 0.635379] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table [ 0.636254] Advanced Linux Sound Architecture Driver Initialized. [ 0.636924] Bluetooth: Core ver 2.22 [ 0.636991] NET: Registered protocol family 31 [ 0.637008] Bluetooth: HCI device and connection manager initialized [ 0.637035] Bluetooth: HCI socket layer initialized [ 0.637055] Bluetooth: L2CAP socket layer initialized [ 0.637093] Bluetooth: SCO socket layer initialized [ 0.638866] tegra210_dvfs: no clock found for sdmmc2_ddr [ 0.638903] tegra210_dvfs: no clock found for sdmmc4_ddr [ 0.638964] tegra210_dvfs: no clock found for sdmmc1_ddr [ 0.638991] tegra210_dvfs: no clock found for sdmmc3_ddr [ 0.642540] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe [ 0.643765] vdd-3v3-sys: supplied by vdd-5v0-sys [ 0.643859] vdd-3v3-sys: 3300 mV [ 0.644150] vdd-1v8-sys: supplied by vdd-3v3-sys [ 0.649269] vdd-usb-vbus2: supplied by vdd-3v3-sys [ 0.649800] vdd-3v3-sd: supplied by vdd-3v3-sys [ 0.649853] vdd-3v3-sd: 3300 mV [ 0.650930] avdd-io-edp-1v05: supplied by avdd-1v05-pll [ 0.650983] avdd-io-edp-1v05: 1050 mV [ 0.651416] vdd-usb-hub-en: supplied by vdd-1v8-sys [ 0.651495] vdd-usb-hub-en: 5000 mV [ 0.652819] camchar: rtcpu character device driver loaded [ 0.653546] extcon-gpio-states extcon:extcon@1: Cable state:0, cable id:0 [ 0.654743] clocksource: Switched to clocksource arch_sys_counter [ 0.695495] VFS: Disk quotas dquot_6.6.0 [ 0.695663] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.696167] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.696602] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000 [ 0.696648] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000) [ 0.696866] cma: enabled page replacement for spfn=d7000, epfn=f0000 [ 0.696887] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful [ 0.696914] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout [ 0.696963] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048 [ 0.696988] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout [ 0.697017] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways [ 0.697038] nvmap_page_pool_init: Total RAM pages: 1010915 [ 0.697053] nvmap_page_pool_init: nvmap page pool size: 126364 pages (493 MB) [ 0.697164] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.697624] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB) [ 0.698639] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB) [ 0.707360] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm [ 0.707860] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm [ 0.708263] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm [ 0.708567] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [ 0.708770] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die [ 0.709050] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz [ 0.709070] pre_t19x_iso_plat_init(): max_iso_bw=11520000KB [ 0.709505] NET: Registered protocol family 2 [ 0.710485] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.710720] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.711264] TCP: Hash tables configured (established 32768 bind 32768) [ 0.711434] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.711532] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.711976] NET: Registered protocol family 1 [ 0.712747] RPC: Registered named UNIX socket transport module. [ 0.712773] RPC: Registered udp transport module. [ 0.712789] RPC: Registered tcp transport module. [ 0.712804] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.713058] Trying to unpack rootfs image as initramfs... [ 1.015717] Freeing initrd memory: 6988K [ 1.025543] host1x 50000000.host1x: initialized [ 1.027361] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.030558] audit: initializing netlink subsys (disabled) [ 1.030653] audit: type=2000 audit(0.867:1): initialized [ 1.031443] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 1.041207] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.042691] ntfs: driver 2.1.32 [Flags: R/W]. [ 1.043703] 9p: Installing v9fs 9p2000 file system support [ 1.046920] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240) [ 1.047077] io scheduler noop registered [ 1.047376] io scheduler cfq registered (default) [ 1.050038] gic 702f9000.agic: GIC IRQ controller registered [ 1.053043] iommu: Adding device 702ef000.adsp to group 33 [ 1.062222] iommu: Adding device aconnect@702c0000:adsp_audio to group 34 [ 1.062390] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered [ 1.063134] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x9248412 [ 1.063166] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4 [ 1.064801] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb [ 1.064930] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb [ 1.065041] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb [ 1.065245] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1 [ 1.065349] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4 [ 1.065460] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4 [ 1.065560] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4 [ 1.065665] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4 [ 1.065765] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb [ 1.065879] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb [ 1.071996] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops [ 1.073706] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000 [ 1.075599] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration [ 1.076884] tegra-pcie 1003000.pcie: PCIE: Enable power rails [ 1.077213] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes [ 1.078362] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [ 1.078605] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=1500000, max_bw=1500000 [ 1.078910] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes [ 1.079168] Adding domain tsec-pd to PM domain host1x-pd [ 1.082456] tsec 54500000.tsec: initialized [ 1.083885] tsec 54100000.tsecb: initialized [ 1.084603] Adding domain nvdec-pd to PM domain host1x-pd [ 1.088032] nvdec 54480000.nvdec: initialized [ 1.089087] Adding domain vic03-pd to PM domain host1x-pd [ 1.089297] Adding domain msenc-pd to PM domain host1x-pd [ 1.089470] Adding domain nvjpg-pd to PM domain host1x-pd [ 1.093393] falcon 54340000.vic: initialized [ 1.094679] falcon 544c0000.nvenc: initialized [ 1.096067] falcon 54380000.nvjpg: initialized [ 1.100384] tegra_cec 70015000.tegra_cec: dt=1 start=0x70015000 end=0x70015FFF irq=97 [ 1.100459] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1 [ 1.100487] tegra_cec 70015000.tegra_cec: Enable clock result: 0. [ 1.100533] tegra_cec 70015000.tegra_cec: tegra_cec_init started [ 1.100575] display board info: id 0x0, fab 0x0 [ 1.100645] generic_infoframe_type: 0x87 [ 1.100781] tegradc tegradc.0: DT parsed successfully [ 1.100837] tegradc tegradc.0: Display dc.ffffff800ab80000 registered with id=0 [ 1.102408] tegra_cec 70015000.tegra_cec: cec_add_sysfs ret=0 [ 1.102439] tegra_cec 70015000.tegra_cec: probed [ 1.109043] tegradc tegradc.0: probed [ 1.109633] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 1.109841] Console: switching to colour frame buffer device 80x30 [ 1.109903] tegradc tegradc.0: fb registered [ 1.111493] tegradc tegradc.1: disp1 connected to head1->/host1x/sor [ 1.111605] tegradc tegradc.1: No lt-data, using default setting [ 1.111647] tegradc tegradc.1: No hpd-gpio in DT [ 1.111697] tegradc tegradc.1: DT parsed successfully [ 1.111766] tegradc tegradc.1: Display dc.ffffff800ad00000 registered with id=1 [ 1.113319] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.116081] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 22 channels [ 1.619092] Host read timeout at address 545c00c4 [ 1.619114] tegra-fuse-burn 7000f800.efuse:efuse-burn: shutdown limit check disabled [ 1.619118] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized [ 1.619509] kfuse 7000fc00.kfuse: initialized [ 1.620231] tegradc tegradc.1: probed [ 1.620487] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available [ 1.620586] tegradc tegradc.1: fb registered [ 1.621346] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0 [ 1.622417] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now [ 1.622444] vdd-cpu: 708 <--> 1322 mV at 708 mV [ 1.622870] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed [ 1.623829] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_evt 1 [ 1.623848] hpd: switching from state 7 (Takeover from bootloader) to state 0 (Reset) [ 1.623867] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0 [ 1.623889] tegradc tegradc.1: blank - powerdown [ 1.623918] extcon-disp-state extcon:disp-state: cable 44 state 0 already set. [ 1.623932] Extcon DP: HPD disabled [ 1.623943] hpd: hpd_switch 0 [ 1.623954] hpd: switching from state 0 (Reset) to state 1 (Check Plug) [ 1.623970] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0 [ 1.623985] hpd: switching from state 1 (Check Plug) to state 3 (Disabled) [ 1.624156] vdd-gpu: applied init 1000000uV constraint [ 1.624173] vdd-gpu: 708 <--> 1323 mV at 997 mV [ 1.624549] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed [ 1.625790] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 [ 1.625819] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.625835] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] [ 1.625852] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] [ 1.625868] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.629004] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.629124] No Device Node present for smmu client: serial8250 !! [ 1.629144] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 1.629202] iommu: Adding device serial8250 to group 35 [ 1.631954] console [ttyS0] disabled [ 1.632028] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra [ 1.670905] pci 0000:00:01.0: BAR 14: assigned [mem 0x13000000-0x130fffff] [ 1.670911] pci 0000:00:02.0: BAR 14: assigned [mem 0x13100000-0x131fffff] [ 1.670916] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff] [ 1.670926] pci 0000:01:00.0: BAR 0: assigned [mem 0x13000000-0x13001fff 64bit] [ 1.670953] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.670960] pci 0000:00:01.0: bridge window [mem 0x13000000-0x130fffff] [ 1.670971] pci 0000:02:00.0: BAR 4: assigned [mem 0x13100000-0x13103fff 64bit] [ 1.670990] pci 0000:02:00.0: BAR 2: assigned [mem 0x13104000-0x13104fff 64bit] [ 1.671008] pci 0000:02:00.0: BAR 0: assigned [io 0x1000-0x10ff] [ 1.671016] pci 0000:00:02.0: PCI bridge to [bus 02] [ 1.671020] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] [ 1.671026] pci 0000:00:02.0: bridge window [mem 0x13100000-0x131fffff] [ 1.671574] pcieport 0000:00:01.0: Signaling PME through PCIe PME interrupt [ 1.671580] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 1.671920] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt [ 1.671924] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt [ 2.110777] tegra_cec 70015000.tegra_cec: Can't find physical addresse. [ 2.110783] tegra_cec 70015000.tegra_cec: tegra_cec_init Done. [ 4.198689] console [ttyS0] enabled [ 4.203454] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART [ 4.212653] serial-tegra 70006200.serial: RX in PIO mode [ 4.218077] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART [ 4.227998] [drm] Initialized [ 4.241327] brd: module loaded [ 4.249760] loop: module loaded [ 4.253063] tegra_profiler: version: 1.143, samples/io: 48/28 [ 4.259161] tegra_profiler: auth: init [ 4.264332] THERMAL EST: found 2 subdevs [ 4.268315] THERMAL EST num_resources: 0 [ 4.272251] [THERMAL EST subdev 0] [ 4.275681] [THERMAL EST subdev 1] [ 4.279558] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est [ 4.288532] THERMAL EST: thz register success. [ 4.293156] THERMAL EST: end of probe, return err: 0 [ 4.299325] sd: No Scsi addr parsed to reserve index [ 4.304346] hisi_sas: driver version v1.6 [ 4.313109] tegra-qspi 70410000.spi: Prod settings list not found [ 4.320418] qspi_mtd spi32766.0: MX25U3235F (4096 Kbytes) [ 4.325870] qspi_mtd spi32766.0: mtd .name = spi32766.0, .size = 0x400000 (4MiB) .erasesize = 0x00001000 (4KiB) .numeraseregions = 0 [ 4.340776] libphy: Fixed MDIO Bus: probed [ 4.345686] tun: Universal TUN/TAP device driver, 1.6 [ 4.350771] tun: (C) 1999-2004 Max Krasnyansky [ 4.357934] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 4.363789] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 4.369778] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 4.376746] igb: Copyright (c) 2007-2014 Intel Corporation. [ 4.382382] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 4.390218] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 4.396195] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4 [ 4.403161] Copyright(c) 1999 - 2017 Intel Corporation. [ 4.409424] r8168 0000:02:00.0: enabling device (0000 -> 0003) [ 4.415307] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded [ 4.435690] r8168 0000:02:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node [ 4.448082] r8168 0000:02:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 48:b0:2d:3c:b0:bb from device tree [ 4.460556] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [ 4.472004] r8168 Copyright (C) 2017 Realtek NIC software team [ 4.472004] This program comes with ABSOLUTELY NO WARRANTY; for details, please see . [ 4.472004] This is free software, and you are welcome to redistribute it under certain conditions; see . [ 4.503384] PPP generic driver version 2.4.2 [ 4.507864] PPP BSD Compression module registered [ 4.512588] PPP Deflate Compression module registered [ 4.517675] PPP MPPE Compression module registered [ 4.522481] NET: Registered protocol family 24 [ 4.526997] usbcore: registered new interface driver r8152 [ 4.532544] usbcore: registered new interface driver asix [ 4.538005] usbcore: registered new interface driver ax88179_178a [ 4.544143] usbcore: registered new interface driver cdc_ether [ 4.550013] usbcore: registered new interface driver net1080 [ 4.555716] usbcore: registered new interface driver cdc_subset [ 4.561680] usbcore: registered new interface driver zaurus [ 4.567323] usbcore: registered new interface driver cdc_ncm [ 4.573147] VFIO - User Level meta-driver version: 0.3 [ 4.579539] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.586100] ehci-pci: EHCI PCI platform driver [ 4.590604] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.596796] ohci-pci: OHCI PCI platform driver [ 4.601290] ohci-platform: OHCI generic platform driver [ 4.609173] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP [ 4.615536] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0 [ 4.623872] tegra-xusb 70090000.xusb: extcon 0: ffffffc0f91e3c00 id [ 4.632214] usbcore: registered new interface driver uas [ 4.633044] tegra-xusb 70090000.xusb: Firmware timestamp: 2019-10-17 15:58:59 UTC, Version: 50.25 release [ 4.633092] tegra-xusb 70090000.xusb: xHCI Host Controller [ 4.633119] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 1 [ 4.633897] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00050010 [ 4.633958] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000 [ 4.634170] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.634176] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.634180] usb usb1: Product: xHCI Host Controller [ 4.634184] usb usb1: Manufacturer: Linux 4.9.201-tegra xhci-hcd [ 4.634187] usb usb1: SerialNumber: 70090000.xusb [ 4.634860] hub 1-0:1.0: USB hub found [ 4.634943] hub 1-0:1.0: 5 ports detected [ 4.635547] tegra-xusb 70090000.xusb: xHCI Host Controller [ 4.635557] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus number 2 [ 4.635668] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.635769] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 4.635774] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.635778] usb usb2: Product: xHCI Host Controller [ 4.635782] usb usb2: Manufacturer: Linux 4.9.201-tegra xhci-hcd [ 4.635785] usb usb2: SerialNumber: 70090000.xusb [ 4.636219] hub 2-0:1.0: USB hub found [ 4.636252] hub 2-0:1.0: 4 ports detected [ 4.636970] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0 [ 4.636975] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0 [ 4.738895] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1 [ 4.738957] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 2 [ 4.739176] usb usb2: usb_suspend_both: status 0 [ 4.800652] usbcore: registered new interface driver usb-storage [ 4.806804] usbcore: registered new interface driver usbserial [ 4.816162] tegra-xudc-new 700d0000.xudc: device count: 1 [ 4.823218] tegra-xudc-new 700d0000.xudc: USB charger detection disabled [ 4.829962] tegra-xudc-new 700d0000.xudc: vbus state: 0 [ 4.835236] tegra-xudc-new 700d0000.xudc: entering ELPG [ 4.839434] mousedev: PS/2 mouse device common for all mice [ 4.839537] usbcore: registered new interface driver xpad [ 4.851791] tegra-xudc-new 700d0000.xudc: entering ELPG done [ 4.962765] usb 1-2: new high-speed USB device number 2 using tegra-xusb [ 4.964032] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 4.966492] rtc rtc1: alarm rtc device [ 4.966510] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 [ 4.966561] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 4.967145] i2c /dev entries driver [ 4.969093] i2c i2c-6: Added multiplexed i2c bus 7 [ 4.969536] i2c i2c-6: Added multiplexed i2c bus 8 [ 4.969543] i2c-mux-gpio cam_i2cmux: 2 port mux on Tegra I2C adapter adapter [ 4.970232] imx477 7-001a: tegracam sensor driver:imx477_v2.0.6 [ 5.048125] usb 1-2: New USB device found, idVendor=0bda, idProduct=5411 [ 5.054848] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 5.061987] usb 1-2: Product: 4-Port USB 2.1 Hub [ 5.066610] usb 1-2: Manufacturer: Generic [ 5.071981] hub 1-2:1.0: USB hub found [ 5.076346] hub 1-2:1.0: 4 ports detected [ 5.159177] usb 2-1: new SuperSpeed USB device number 2 using tegra-xusb [ 5.191342] usb 2-1: New USB device found, idVendor=0bda, idProduct=0411 [ 5.198059] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 5.205201] usb 2-1: Product: 4-Port USB 3.1 Hub [ 5.209826] usb 2-1: Manufacturer: Generic [ 5.217432] hub 2-1:1.0: USB hub found [ 5.221987] hub 2-1:1.0: 4 ports detected [ 5.272292] imx477 8-001a: tegracam sensor driver:imx477_v2.0.6 [ 5.302763] usb 1-3: new full-speed USB device number 3 using tegra-xusb [ 5.328710] usb 1-3: New USB device found, idVendor=8087, idProduct=0a2b [ 5.335424] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 5.406759] usb 1-2.2: new full-speed USB device number 4 using tegra-xusb [ 5.435362] usb 1-2.2: New USB device found, idVendor=046d, idProduct=c52b [ 5.442250] usb 1-2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 5.449564] usb 1-2.2: Product: USB Receiver [ 5.453839] usb 1-2.2: Manufacturer: Logitech [ 5.515116] usb 2-1.3: new SuperSpeed USB device number 3 using tegra-xusb [ 5.540183] usb 2-1.3: New USB device found, idVendor=090c, idProduct=1000 [ 5.547069] usb 2-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 5.554382] usb 2-1.3: Product: Flash Drive FIT [ 5.558920] usb 2-1.3: Manufacturer: Samsung [ 5.563196] usb 2-1.3: SerialNumber: 0306321020003681 [ 5.569318] usb-storage 2-1.3:1.0: USB Mass Storage device detected [ 5.575887] scsi host0: usb-storage 2-1.3:1.0 [ 5.580272] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x1a [ 5.580354] imx477 8-001a: imx477_board_setup: error during i2c read probe (-121) [ 5.580394] imx477 8-001a: board setup failed [ 5.580506] imx477: probe of 8-001a failed with error -121 [ 5.586845] max77620-power max77620-power: Event recorder REG_NVERC : 0x0 [ 5.612143] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2 [ 5.619354] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4 [ 5.626857] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 5.636189] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC [ 5.645165] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC [ 5.654184] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 5.663508] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC [ 5.672472] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC [ 5.681501] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 5.690817] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC [ 5.699785] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature [ 5.707800] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19 [ 5.715732] tegra_aotag tegra-aotag: Registering sensor 0 [ 5.721245] tegra_aotag tegra-aotag: Bound to TZ : ID 0 [ 5.726488] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0 [ 5.733009] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 5.742353] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered [ 5.750582] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered [ 5.759363] parse_throttle_dt_data: Num cap clks = 6 [ 5.764342] parse_throttle_dt_data: clk=cclk_g type=2 [ 5.769413] parse_throttle_dt_data: clk=gpu type=4 [ 5.774235] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0 [ 5.780354] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0 [ 5.786470] parse_throttle_dt_data: clk=cap.throttle.sclk type=0 [ 5.792485] parse_throttle_dt_data: clk=emc type=3 [ 5.797691] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 5.807124] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 5.816585] tegra_throttle_probe: probe successful. #cdevs=4 [ 5.823046] FAN dev name: pwm-fan [ 5.826437] FAN:gpio request success. [ 5.830186] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255 [ 5.836167] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal [ 5.842953] pwm_fan_driver pwm-fan: fan tach request irq success [ 5.848981] pwm_fan_driver pwm-fan: tach period: 1000 [ 5.854147] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2 [ 5.861729] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2 [ 5.869476] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2 [ 5.877311] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2 [ 5.885144] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3 [ 5.892980] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3 [ 5.900814] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3 [ 5.908650] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4 [ 5.916484] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4 [ 5.924402] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4 [ 5.935023] device-mapper: uevent: version 1.0.3 [ 5.940132] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 5.954061] tegra210-cpufreq cpufreq: probe()...completed [ 5.960253] sdhci: Secure Digital Host Controller Interface driver [ 5.966432] sdhci: Copyright(c) Pierre Ossman [ 5.970791] sdhci-pltfm: SDHCI platform and OF driver helper [ 5.976932] sdhci-tegra sdhci-tegra.0: Got CD GPIO [ 5.982090] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful [ 5.989358] sdhci-tegra sdhci-tegra.0: wakeup init done, cdirq 300 [ 6.000712] tegra-se 70012000.se: tegra_se_probe: complete [ 6.006688] hidraw: raw HID events driver (C) Jiri Kosina [ 6.020270] usbcore: registered new interface driver usbhid [ 6.025870] usbhid: USB HID core driver [ 6.031773] tegra21x_actmon 6000c800.actmon: in actmon_register()... [ 6.038351] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all [ 6.046984] mmc0: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA 64-bit with 64 bit addr [ 6.048558] nvpmodel: initialized successfully [ 6.049669] usbcore: registered new interface driver snd-usb-audio [ 6.049723] No Device Node present for smmu client: snd-soc-dummy !! [ 6.049728] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 6.049746] iommu: Adding device snd-soc-dummy to group 36 [ 6.057171] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input0 [ 6.074047] OPE platform probe [ 6.074134] OPE platform probe successful [ 6.074407] OPE platform probe [ 6.074486] OPE platform probe successful [ 6.098835] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok [ 6.098962] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok [ 6.099085] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok [ 6.099206] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok [ 6.099329] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok [ 6.099446] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok [ 6.099569] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok [ 6.099690] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok [ 6.099812] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok [ 6.099934] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok [ 6.111199] u32 classifier [ 6.111200] Actions configured [ 6.111269] Initializing XFRM netlink socket [ 6.111972] NET: Registered protocol family 10 [ 6.112685] NET: Registered protocol family 17 [ 6.112696] NET: Registered protocol family 15 [ 6.112769] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 6.112817] Bluetooth: RFCOMM socket layer initialized [ 6.112826] Bluetooth: RFCOMM ver 1.11 [ 6.112830] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 6.112835] Bluetooth: HIDP socket layer initialized [ 6.112853] 9pnet: Installing 9P2000 support [ 6.112891] Key type dns_resolver registered [ 6.116815] Registered cp15_barrier emulation handler [ 6.116821] Registered setend emulation handler [ 6.117871] registered taskstats version 1 [ 6.118511] Adding domain ve2-pd to PM domain host1x-pd [ 6.118759] Adding domain ve-pd to PM domain host1x-pd [ 6.120753] isp 54600000.isp: initialized [ 6.121681] isp 54680000.isp: initialized [ 6.131947] last reset is due to power on reset [ 6.131950] KERNEL: PMC reset status reg: 0x0 [ 6.132009] BL: PMC reset status reg: 0x0 [ 6.132011] BL: PMIC poweroff Event Recorder: 0x40 [ 6.133466] clk_cbus_recalc_rate: no gbus parent [ 6.133470] clk_cbus_round_rate: no gbus parent [ 6.133472] clk_cbus_round_rate: no gbus parent [ 6.133479] clk_cbus_recalc_rate: no gbus parent [ 6.133581] clk_cbus_recalc_rate: no gbus parent [ 6.133584] clk_cbus_round_rate: no gbus parent [ 6.133585] clk_cbus_round_rate: no gbus parent [ 6.133588] clk_cbus_recalc_rate: no gbus parent [ 6.133601] tegra_dvfs: GPU-cap: registered [ 6.133660] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled [ 6.133662] tegra dvfs: vdd-core: nominal 1125mV, offset 600000uV, step 12500uV, scaling enabled [ 6.133664] tegra dvfs: vdd-gpu: nominal 1078mV, offset 708000uV, step 10000uV, scaling enabled [ 6.135059] tegra_dvfs: vdd-gpu-vts: registered [ 6.135742] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered [ 6.136373] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered [ 6.136850] input: gpio-keys as /devices/gpio-keys/input/input1 [ 6.168744] tegra_rtc 7000e000.rtc: setting system clock to 2000-01-01 01:00:18 UTC (946688418) [ 6.169744] vi 54080000.vi: vi_probe: ++ [ 6.172870] vi 54080000.vi: initialized [ 6.174914] vi 54080000.vi: subdev nvcsi--2 bound [ 6.174931] vi 54080000.vi: subdev imx477 7-001a bound [ 6.175699] vi 54080000.vi: subdev nvcsi--1 bound [ 6.176456] Disable partitions left on by BL [ 6.176459] disb [ 6.176495] bwmgr: missing cdev-type property [ 6.176585] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 6.176591] DRAM derating cdev registered. [ 6.177520] ALSA device list: [ 6.177523] #0: tegra-hda at 0x70038000 irq 83 [ 6.177524] #1: tegra-snd-t210ref-mobile-rt565x [ 6.449141] Freeing unused kernel memory: 8576K [ 6.477796] Root device found: mmcblk0p1 [ 8.205280] scsi 0:0:0:0: Direct-Access Samsung Flash Drive FIT 1100 PQ: 0 ANSI: 6 [ 8.214049] sd 0:0:0:0: [sda] 501253132 512-byte logical blocks: (257 GB/239 GiB) [ 8.221761] sd 0:0:0:0: [sda] Write Protect is off [ 8.226708] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.243574] sda: sda1 [ 8.246821] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 16.635750] ERROR: mmcblk0p1 not found CTRL-A Z for help | 115200 8N1 | NOR | Minicom 2.7.1 | VT102 | Offline | ttyUSB0