Error writing session log (raw mode) to file: putty.log [0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-8728f3cb) [0000.130] Processing in cold boot mode Bootloader 2 [0000.135] A02 Bootrom Patch rev = 1023 [0000.138] Power-up reason: pmc por [0000.141] No Battery Present [0000.144] pmic max77620 reset reason [0000.147] pmic max77620 NVERC : 0x4e [0000.151] RamCode = 0 [0000.153] Platform has DDR4 type RAM [0000.156] max77620 disabling SD1 Remote Sense [0000.161] Setting DDR voltage to 1125mv [0000.165] Serial Number of Pmic Max77663: 0x317f6 [0000.172] Entering ramdump check [0000.175] Get RamDumpCarveOut = 0x0 [0000.178] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.184] Last reboot was clean, booting normally! [0000.188] Sdram initialization is successful [0000.192] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000 [0000.198] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000 [0000.204] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000 [0000.210] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000 [0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000 [0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000 [0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000 [0000.233] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000 [0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000 [0000.256] Platform-DebugCarveout: 0 [0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000 [0000.265] Non secure mode, and RB not enabled. [0000.269] BoardID = 3448, SKU = 0x0 [0000.272] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.276] Nano-SD: checking PT table on QSPI ... [0000.280] Initialize FailControl [0000.283] Read PT from (2:0) [0000.314] PT crc32 and magic check passed. [0000.318] Using BFS PT to query partitions [0000.323] Loading Tboot-CPU binary [0000.352] Verifying TBC in OdmNonSecureSBK mode [0000.362] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.369] Bootloader downloaded successfully. [0000.373] Downloaded Tboot-CPU binary to 0xa0000258 [0000.378] MAX77620_GPIO5 configured [0000.381] CPU power rail is up [0000.384] CPU clock enabled [0000.388] Performing RAM repair [0000.391] Updating A64 Warmreset Address to 0xa00002e9 [0000.396] BoardID = 3448, SKU = 0x0 [0000.399] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.403] Nano-SD: checking PT table on QSPI ... [0000.407] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.413] Loading NvTbootBootloaderDTB [0000.480] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.551] Bootloader DTB Load Address: 0x83000000 [0000.556] BoardID = 3448, SKU = 0x0 [0000.559] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.563] Nano-SD: checking PT table on QSPI ... [0000.567] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.573] Loading NvTbootKernelDTB [0000.639] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.711] Kernel DTB Load Address: 0x83100000 [0000.715] BoardID = 3448, SKU = 0x0 [0000.718] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.722] Nano-SD: checking PT table on QSPI ... [0000.726] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.734] Loading cboot binary [0000.850] Verifying EBT in OdmNonSecureSBK mode [0000.892] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0000.899] Bootloader downloaded successfully. [0000.903] BoardID = 3448, SKU = 0x0 [0000.906] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.910] Nano-SD: checking PT table on QSPI ... [0000.914] NvTbootFailControlDoFailover: No failover; Continuing ... [0000.920] PT: Partition NCT NOT found ! [0000.924] Warning: Find Partition via PT Failed [0000.928] Next binary entry address: 0x92c00258 [0000.933] BoardId: 3448 [0000.938] Overriding pmu board id with proc board id [0000.942] Display board id is not available [0000.947] BoardID = 3448, SKU = 0x0 [0000.950] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0000.954] Nano-SD: checking PT table on QSPI ... [0000.958] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.065] Verifying SC7EntryFw in OdmNonSecureSBK mode [0001.121] /bpmp deleted [0001.123] SC7EntryFw header found loaded at 0xff700000 [0001.311] OVR2 PMIC [0001.312] Bpmp FW successfully loaded [0001.316] BoardID = 3448, SKU = 0x0 [0001.319] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.323] Nano-SD: checking PT table on QSPI ... [0001.327] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.334] WB0 init successfully at 0xff780000 [0001.339] Verifying NvTbootWb0 in OdmNonSecureSBK mode [0001.344] Set NvDecSticky Bits [0001.347] GSC2 address ff53fffc value c0edbbcc [0001.353] GSC MC Settings done [0001.356] BoardID = 3448, SKU = 0x0 [0001.360] QSPI-ONLY: SkipQspiOnlyFlag = 0 [0001.363] Nano-SD: checking PT table on QSPI ... [0001.368] NvTbootFailControlDoFailover: No failover; Continuing ... [0001.375] TOS Image length 53680 [0001.378] Monitor size 53680 [0001.381] OS size 0 [0001.396] Secure Os AES-CMAC Verification Success! [0001.400] TOS image cipher info: plaintext [0001.404] Loading and Validation of Secure OS Successful [0001.420] SC7 Entry Firmware - 0xff700000, 0x4000 [0001.425] NvTbootPackSdramParams: start. [0001.430] NvTbootPackSdramParams: done. [0001.434] Tegraboot started after 51856 us [0001.438] Basic modules init took 935922 us [0001.442] Sec Bootdevice Read Time = 12 ms, Read Size = 61 KB [0001.447] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.453] Next stage binary read took 102860 us [0001.457] Carveout took -132463 us [0001.460] CPU initialization took 510367 us [0001.464] Total time taken by TegraBoot 1416686 us [0001.469] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.3(release):b5eeb33f7 NOTICE: BL31: Built : 12:09:37, Jul 26 2021 ERROR: Error initializing runtime service trusty_fast [0001.591] RamCode = 0 [0001.596] LPDDR4 Training: Read DT: Number of tables = 2 [0001.601] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.614] EMC Training Successful [0001.617] 408000 not found in DVFS table [0001.623] RamCode = 0 [0001.626] DT Write: emc-table@204000 succeeded [0001.632] DT Write: emc-table@1600000 succeeded [0001.636] LPDDR4 Training: Write DT: Number of tables = 2 [0001.684] [0001.685] Debug Init done [0001.688] Marked DTB cacheable [0001.691] Bootloader DTB loaded at 0x83000000 [0001.696] Marked DTB cacheable [0001.699] Kernel DTB loaded at 0x83100000 [0001.702] DeviceTree Init done [0001.715] Pinmux applied successfully [0001.720] gicd_base: 0x50041000 [0001.723] gicc_base: 0x50042000 [0001.726] Interrupts Init done [0001.730] Using base:0x60005090 & irq:208 for tick-timer [0001.736] Using base:0x60005098 for delay-timer [0001.740] platform_init_timer: DONE [0001.743] Timer(tick) Init done [0001.747] osc freq = 38400 khz [0001.751] [0001.752] Welcome to L4T Cboot [0001.755] [0001.756] Cboot Version: 00.00.2018.01-t210-c952b4e6 [0001.761] calling constructors [0001.764] initializing heap [0001.767] initializing threads [0001.770] initializing timers [0001.773] creating bootstrap completion thread [0001.777] top of bootstrap2() [0001.780] CPU: ARM Cortex A57 [0001.783] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.788] initializing platform [0001.795] Manufacturer: MF = 0xc2, ID MSB = 0x25 [0001.799] ID LSB = 0x36, ID-CFI len = 194 bytes [0001.804] Macronix QSPI chip present [0001.807] SPI device register [0001.810] init boot device [0001.813] allocating memory for boot device(SPI) [0001.817] registering boot device [0001.836] QSPI bdev is already initialized [0001.840] Enable APE clock [0001.842] Un-powergate APE partition [0001.846] of_register: registering tegra_udc to of_hal [0001.851] of_register: registering inv20628-driver to of_hal [0001.857] of_register: registering ads1015-driver to of_hal [0001.862] of_register: registering lp8557-bl-driver to of_hal [0001.868] of_register: registering bq2419x_charger to of_hal [0001.873] of_register: registering bq27441_fuel_gauge to of_hal [0001.885] gpio framework initialized [0001.888] of_register: registering tca9539_gpio to of_hal [0001.894] of_register: registering tca9539_gpio to of_hal [0001.899] of_register: registering i2c_bus_driver to of_hal [0001.905] of_register: registering i2c_bus_driver to of_hal [0001.910] of_register: registering i2c_bus_driver to of_hal [0001.916] pmic framework initialized [0001.919] of_register: registering max77620_pmic to of_hal [0001.925] regulator framework initialized [0001.929] of_register: registering tps65132_bl_driver to of_hal [0001.934] initializing target [0001.940] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.948] board ID = D78, board SKU = 0 [0001.952] Skipping Z3! [0001.957] fixed regulator driver initialized [0001.974] initializing OF layer [0001.977] NCK carveout not present [0001.980] Skipping dts_overrides [0001.984] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.001] I2C Bus Init done [0002.003] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.014] I2C Bus Init done [0002.016] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.026] I2C Bus Init done [0002.029] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.039] I2C Bus Init done [0002.042] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.052] I2C Bus Init done [0002.055] of_children_init: Ops found for compatible string maxim,max77620 [0002.065] max77620_init using irq 118 [0002.070] register 'maxim,max77620' pmic [0002.074] gpio_driver_register: register 'max77620-gpio' driver [0002.080] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.091] I2C Bus Init done [0002.094] NCK carveout not present [0002.104] Find /i2c@7000c000's alias i2c0 [0002.108] get eeprom at 1-a0, size 256, type 0 [0002.116] Find /i2c@7000c500's alias i2c2 [0002.120] get eeprom at 3-a0, size 256, type 0 [0002.124] get eeprom at 3-ae, size 256, type 0 [0002.129] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.134] I2C slave not started [0002.137] I2C write failed [0002.140] Writing offset failed [0002.143] eeprom_init: EEPROM read failed [0002.147] pm_ids_update: eeprom init failed [0002.151] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.181] pm_ids_update: The pm board id is 3448-0000-400 [0002.188] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.196] pm_ids_update: pm id update successful [0002.201] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.231] pm_ids_update: The pm board id is 3449-0000-400 [0002.237] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.245] pm_ids_update: pm id update successful [0002.275] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.281] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0002.289] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0002.295] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0002.303] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ec:a1:78 [0002.309] Plugin Manager: Parse ODM data 0x000a4000 [0002.322] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0002.336] Find /i2c@7000c000's alias i2c0 [0002.340] get eeprom at 1-a0, size 256, type 0 [0002.349] Find /i2c@7000c500's alias i2c2 [0002.352] get eeprom at 3-a0, size 256, type 0 [0002.357] get eeprom at 3-ae, size 256, type 0 [0002.361] pm_ids_update: Updating 1,a0, size 256, type 0 [0002.367] I2C slave not started [0002.370] I2C write failed [0002.372] Writing offset failed [0002.375] eeprom_init: EEPROM read failed [0002.379] pm_ids_update: eeprom init failed [0002.383] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.413] pm_ids_update: The pm board id is 3448-0000-400 [0002.420] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0002.427] pm_ids_update: pm id update successful [0002.431] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.461] pm_ids_update: The pm board id is 3449-0000-400 [0002.467] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0002.474] pm_ids_update: pm id update successful [0002.505] Add serial number:1424220032136 as DT property [0002.512] Applying platform configs [0002.519] platform-init is not present. Skipping [0002.523] calling apps_init() [0002.529] Couldn't find GPT header [0002.534] Proceeding to Cold Boot [0002.537] starting app android_boot_app [0002.541] Device state: unlocked [0002.544] display console init [0002.552] could not find regulator [0002.555] hdmi cable connected [0002.571] edid read success [0002.586] DT entry for leds-pwm not found [0002.590] edid read success [0002.592] width = 640, height = 480, frequency = 25174825 [0002.598] width = 640, height = 480, frequency = 25174825 [0002.603] width = 1920, height = 1080, frequency = 148500000 [0002.609] width = 1920, height = 1080, frequency = 148500000 [0002.614] width = 1920, height = 1080, frequency = 148351648 [0002.620] width = 1280, height = 720, frequency = 74175824 [0002.626] width = 720, height = 480, frequency = 26973026 [0002.631] width = 640, height = 480, frequency = 25174825 [0002.636] width = 720, height = 576, frequency = 26973026 [0002.642] width = 1920, height = 1080, frequency = 148351648 [0002.647] width = 1920, height = 1080, frequency = 148351648 [0002.653] width = 1280, height = 720, frequency = 74175824 [0002.658] Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.666] tmds-config node not found [0002.670] pmc_set_io_pad_voltage: Error -2 retrieving platform-io-pad-voltagepropsetting 'avdd-io-hdmi-dp' regulator to 1050000 micro volts [0002.685] setting 'vdd-1v8' regulator to 1800000 micro volts [0002.693] could not find regulator [0002.696] could not find regulator [0002.699] could not find regulator [0002.728] using default cmu settings [0002.731] dc_hdmi_enable, starting HDMI initialisation [0002.737] dc_hdmi_enable, HDMI initialisation complete [0002.742] list and configure display window [0002.751] display console init completed [0002.762] subnode volume_up is not found ! [0002.766] subnode back is not found ! [0002.769] subnode volume_down is not found ! [0002.774] subnode menu is not found ! [0002.777] Gpio keyboard init success [0002.858] found decompressor handler: lz4-legacy [0002.872] decompressing blob (type 1)... [0002.942] load_bmp_blob: panelresolution=1080 type=3 [0003.018] decompressor handler not found [0003.022] load_firmware_blob: Firmware blob loaded, entries=2 [0003.027] XUSB blob version 0 size 126464 @ 0x934ae28c [0003.033] -------> se_aes_verify_sbk_clear: 747 [0003.038] se_aes_verify_sbk_clear: Error [0003.042] SE operation failed [0003.045] bl_battery_charging: connected to external power supply [0003.057] device_query_partition_size: failed to open partition spiflash0:MSC ! [0003.064] MSC Partition not found [0003.070] device_query_partition_size: failed to open partition spiflash0:USP ! [0003.077] USP partition read failed! [0003.081] blob_init: blob-partition USP header read failed [0003.086] android_boot Unable to update recovery partition [0003.092] kfs_getpartname: name = LNX [0003.096] Loading kernel from LNX [0003.105] Found 19 BFS partitions in "spiflash0" [0003.427] load kernel from storage [0003.432] decompressor handler not found [0003.698] Successfully loaded kernel and ramdisk images [0003.703] board ID = D78, board SKU = 0 [0003.708] sdmmc node status = okay [0003.711] sdcard instance = 0 [0003.714] sdmmc cd-inverted [0003.716] sdcard gpio handle 0x5b [0003.720] sdcard gpio pin 0xc9 [0003.723] sdcard gpio flags 0x0 [0003.726] vmmc-supply 0x9d [0003.728] cd_gpio_pin = 201 [0003.731] pin_state = 1 [0003.733] No sdcard [0003.735] SD-card NOT present ... [0003.738] load_and_boot_kernel: SD card not detected! [0003.744] load_bmp_blob: panelresolution=1080 type=3 [0004.240] display bmp image done [0009.244] load_bmp_blob: panelresolution=1080 type=3 [0009.738] display bmp image done [0009.741] NCK carveout not present [0009.744] Skipping dts_overrides [0009.747] NCK carveout not present [0009.757] Find /i2c@7000c000's alias i2c0 [0009.761] get eeprom at 1-a0, size 256, type 0 [0009.769] Find /i2c@7000c500's alias i2c2 [0009.773] get eeprom at 3-a0, size 256, type 0 [0009.777] get eeprom at 3-ae, size 256, type 0 [0009.782] pm_ids_update: Updating 1,a0, size 256, type 0 [0009.787] I2C slave not started [0009.790] I2C write failed [0009.793] Writing offset failed [0009.796] eeprom_init: EEPROM read failed [0009.800] pm_ids_update: eeprom init failed [0009.804] pm_ids_update: Updating 3,a0, size 256, type 0 [0009.834] pm_ids_update: The pm board id is 3448-0000-400 [0009.841] Adding plugin-manager/ids/3448-0000-400=/i2c@7000c500:module@0x50 [0009.849] pm_ids_update: pm id update successful [0009.854] pm_ids_update: Updating 3,ae, size 256, type 0 [0009.884] pm_ids_update: The pm board id is 3449-0000-400 [0009.890] Adding plugin-manager/ids/3449-0000-400=/i2c@7000c500:module@0x57 [0009.898] pm_ids_update: pm id update successful [0009.928] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0009.934] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB [0009.942] eeprom_get_mac: EEPROM invalid MAC address (all 0xff) [0009.948] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB [0009.956] updating /chosen/nvidia,ethernet-mac node 00:04:4b:ec:a1:78 [0009.962] Plugin Manager: Parse ODM data 0x000a4000 [0009.975] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x70006000 [0009.983] Add serial number:1424220032136 as DT property [0009.992] "bpmp" doesn't exist, creating [0009.997] Updated bpmp info to DTB [0010.002] Updated initrd info to DTB [0010.006] "proc-board" doesn't exist, creating [0010.012] Updated board info to DTB [0010.015] "pmu-board" doesn't exist, creating [0010.021] Updated board info to DTB [0010.024] "display-board" doesn't exist, creating [0010.030] Updated board info to DTB [0010.034] "reset" doesn't exist, creating [0010.038] Updated reset info to DTB [0010.042] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 [0010.081] DTB cmdline: earlycon=uart8250,mmio32,0x70006000 [0010.087] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 [0010.100] Updated bootarg info to DTB [0010.103] Adding uuid 000000016450b7011c00000012fd80c0 to DT [0010.109] Adding eks info 0 to DT [0010.115] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0010.121] Updated memory info to DTB [0010.128] set vdd_core voltage to 1125 mv [0010.132] setting 'vdd-core' regulator to 1125000 micro volts [0010.138] Found secure-pmc; disable BPMP U-Boot 2020.04-g46e4604c78 (Jul 26 2021 - 12:09:42 -0700) SoC: tegra210 Model: NVIDIA Jetson Nano Developer Kit Board: NVIDIA P3450-0000 DRAM: 4 GiB MMC: sdhci@700b0000: 1, sdhci@700b0600: 0 Loading Environment from SPI Flash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 MMC: no card present Card did not respond to voltage select! starting USB... Bus usb@7d000000: tegrausb: Invalid dr_mode 2 for host mode probe failed, error -1 Bus xusb@70090000: Firmware size 126464 Firmware timestamp: 0x5f23e558, Version: 50.26 release Register HCSParams1: 9000124 NbrPorts: 9 Starting the controller USB XHCI 1.00 scanning bus xusb@70090000 for devices... 5 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: Kingston Rev: PMAP Prod: DataTraveler 3.0 Type: Removable Hard Disk Capacity: 29556.0 MB = 28.8 GB (60530688 x 512) ... is now current device Scanning usb 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 845 bytes read in 5 ms (165 KiB/s) 1: primary kernel Retrieving file: /boot/initrd 7160133 bytes read in 80 ms (85.4 MiB/s) Retrieving file: /boot/Image 34484232 bytes read in 367 ms (89.6 MiB/s) append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,4 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1125 core_edp_ma=4000 gpt tegra_fbmem=0x800000@0x92ca9000 is_hdmi_initialised=1 earlycon=uart8250,mmio32,0x70006000 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 ERROR: reserving fdt memory region failed (addr=0 size=0) ERROR: reserving fdt memory region failed (addr=0 size=0) Using Device Tree in place at 0000000083100000, end 000000008317ce2a copying carveout for /host1x@50000000/dc@54200000... copying carveout for /host1x@50000000/dc@54240000... Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.253-tegra (buildbrain@mobile-u64-5496-d5000) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Mon Jul 26 12:13:06 PDT 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32, [ 0.000000] OF: fdt: - 80000000 , 7ee00000 [ 0.000000] OF: fdt: - 100000000 , 7f200000 [ 0.000000] Found tegra_fbmem: 00800000@92ca9000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 1.161325] tegradc tegradc.1: dpd enable lookup fail:-19 [ 1.323803] imx219 7-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.323870] imx219 7-0010: board setup failed [ 1.347687] imx219 8-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.347743] imx219 8-0010: board setup failed