[ 0.000000] Booting Linux on physical CPU 0x100 [ 0.000000] Linux version 4.9.253-tegra (fazevedo@PDM-00863) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Fri Nov 5 15:14:33 WET 2021 [ 0.000000] Boot CPU: AArch64 Processor [411fd073] [ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 80, [ 0.000000] OF: fdt: - 80000000 , 70000000 [ 0.000000] OF: fdt: - f0200000 , 85600000 [ 0.000000] OF: fdt: - 175e00000 , 200000 [ 0.000000] OF: fdt: - 176600000 , 200000 [ 0.000000] OF: fdt: - 177000000 , 200000 [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000003100000 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] Found tegra_fbmem: 00140000@96085000 [ 0.000000] Found lut_mem: 00002008@96081000 [ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 64 MiB at 0x00000000fc000000 [ 0.000000] On node 0 totalpages: 1006269 [ 0.000000] DMA zone: 8192 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 523453 pages, LIFO batch:31 [ 0.000000] Normal zone: 7624 pages used for memmap [ 0.000000] Normal zone: 482816 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57624 r8192 d32488 u98304 [ 0.000000] pcpu-alloc: s57624 r8192 d32488 u98304 alloc=24*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 990453 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 isolcpus=1-2 video=tegrafb earlycon=uart8250,mmio32,0x3100000 nvdumper_reserved=0x1772e0000 gpt rootfs.slot_suffix= tegra_fbmem=0x140000@0x96085000 lut_mem=0x2008@0x96081000 usbcore.old_scheme_first=1 tegraid=18.1.2.0.0 maxcpus=6 no_console_suspend boot.slot_suffix= boot.ratchetvalues=0.2031647.1 vpr_resize bl_prof_dataptr=0x10000@0x175840000 sdhci_tegra.en_boot_part_access=1 quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 isolcpus=1-2 [ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes [ 0.000000] log_buf_len total cpu_extra contributions: 163840 bytes [ 0.000000] log_buf_len min size: 32768 bytes [ 0.000000] log_buf_len: 262144 bytes [ 0.000000] early log buf free: 29780(90%) [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 3154624K/4025076K available (15358K kernel code, 2960K rwdata, 6864K rodata, 8640K init, 612K bss, 116788K reserved, 753664K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f80000 ( 15360 KB) [ 0.000000] .rodata : 0xffffff8008f80000 - 0xffffff8009640000 ( 6912 KB) [ 0.000000] .init : 0xffffff8009640000 - 0xffffff8009eb0000 ( 8640 KB) [ 0.000000] .data : 0xffffff8009eb0000 - 0xffffff800a194008 ( 2961 KB) [ 0.000000] .bss : 0xffffff800a194008 - 0xffffff800a22d0b4 ( 613 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf03dc8000 ( 61 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0f7200000 ( 3954 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=6. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 31.25MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xe6a171046, max_idle_ns: 881590405314 ns [ 0.000003] sched_clock: 56 bits at 31MHz, resolution 32ns, wraps every 4398046511088ns [ 0.000937] Console: colour dummy device 80x25 [ 0.000942] console [tty0] enabled [ 0.000946] bootconsole [uart8250] disabled [ 0.000954] kmemleak: Kernel memory leak detector disabled [ 0.000963] Calibrating delay loop (skipped), value calculated using timer frequency.. 62.50 BogoMIPS (lpj=125000) [ 0.000970] pid_max: default: 32768 minimum: 301 [ 0.001275] Security Framework initialized [ 0.001428] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.001433] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.002002] ftrace: allocating 47144 entries in 185 pages [ 0.125563] sched-energy: Sched-energy-costs installed from DT [ 0.125573] ASID allocator initialised with 65536 entries [ 0.160842] tegra-id: chipid=21817. [ 0.160848] tegra-id: opt_subrevision=1. [ 0.160867] Tegra Revision: A02p SKU: 0xdc CPU Process: 0 SoC Process: 0 [ 0.160875] DTS File Name: arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t18x/lanai/kernel-dts/tegra186-p3636-0001-p3509-0000-a01.dts [ 0.160880] DTB Build time: [ 0.210642] CPU1: Booted secondary processor [4e0f0030] [ 0.242008] CPU2: Booted secondary processor [4e0f0030] [ 0.273025] CPU3: Booted secondary processor [411fd073] [ 0.304985] CPU4: Booted secondary processor [411fd073] [ 0.336975] CPU5: Booted secondary processor [411fd073] [ 0.337027] Brought up 6 CPUs [ 0.337031] SMP: Total of 6 processors activated. [ 0.337036] CPU features: detected feature: 32-bit EL0 Support [ 0.339378] CPU: All CPU(s) started at EL2 [ 0.339516] alternatives: patching kernel code [ 0.342016] devtmpfs: initialized [ 0.364444] Initilizing CustomIPI irq domain [ 0.364586] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.364597] futex hash table entries: 2048 (order: 5, 131072 bytes) [ 0.373108] pinctrl core: initialized pinctrl subsystem [ 0.373346] OS set in device tree is not L4T. [ 0.373514] regulator-dummy: no parameters [ 0.373648] Initializing plugin-manager [ 0.373704] Plugin module not found [ 0.373738] Plugin-manager status disabled [ 0.374795] NET: Registered protocol family 16 [ 0.375843] pstore: using zlib compression [ 0.375855] console [pstore-1] enabled [ 0.375858] pstore: Registered ramoops as persistent store backend [ 0.375862] ramoops: attached 0x200000@0x175880000, ecc: 0/0 [ 0.389036] cpuidle: using governor menu [ 0.389921] bpmp: waiting for handshake [ 0.389924] bpmp: handshake completed [ 0.389944] bpmp: synchronizing channels [ 0.389952] bpmp: channels synchronized [ 0.389956] bpmp: mail init ok [ 0.391433] arm-smmu 12000000.iommu: probing hardware configuration... [ 0.391439] arm-smmu 12000000.iommu: SMMUv2 with: [ 0.391443] arm-smmu 12000000.iommu: stage 1 translation [ 0.391447] arm-smmu 12000000.iommu: stage 2 translation [ 0.391450] arm-smmu 12000000.iommu: nested translation [ 0.391457] arm-smmu 12000000.iommu: stream matching with 128 register groups, mask 0x7f80 [ 0.391462] arm-smmu 12000000.iommu: SMMU address space size (0x800000) differs from mapped region size (0x1000000)! [ 0.391466] arm-smmu 12000000.iommu: 64 context banks (0 stage-2 only) [ 0.391471] arm-smmu 12000000.iommu: Stage-1: 39-bit VA -> 48-bit IPA [ 0.391474] arm-smmu 12000000.iommu: Stage-2: 39-bit IPA -> 48-bit PA [ 0.393298] vdso: 2 pages (1 code @ ffffff8008f87000, 1 data @ ffffff8009eb4000) [ 0.393311] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.396481] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations [ 0.397423] Registering BPMP clocks... [ 0.397491] tegra_bpmp_clk_init: clock init ok (638 clks) [ 0.397937] Serial: AMBA PL011 UART driver [ 0.398847] tegra_powergate_init: DONE [ 0.398856] DTS File Name: arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t18x/lanai/kernel-dts/tegra186-p3636-0001-p3509-0000-a01.dts [ 0.398860] DTB Build time: [ 0.400104] Tegra reboot handler registered. [ 0.401269] tegra-pmc c360000.pmc: scratch reg offset dts data not present [ 0.401330] tegra-pmc: get_secure_pmc_setting: done secure_pmc=0 [ 0.401343] tegra-pmc: ### PMC reset source: TEGRA_POWER_ON_RESET [ 0.401346] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_L0 [ 0.401348] tegra-pmc: ### PMC reset status reg: 0x0 [ 0.401496] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [ 0.401506] tegra-pmc c360000.pmc: IO padctrl driver initialized [ 0.401777] iommu: Adding device 3460000.sdhci to group 0 [ 0.402183] iommu: Adding device 3440000.sdhci to group 1 [ 0.403184] iommu: Adding device 3160000.i2c to group 2 [ 0.403580] iommu: Adding device c240000.i2c to group 3 [ 0.403870] iommu: Adding device 3180000.i2c to group 4 [ 0.404163] iommu: Adding device 3190000.i2c to group 5 [ 0.404525] iommu: Adding device 31b0000.i2c to group 6 [ 0.404816] iommu: Adding device 31c0000.i2c to group 7 [ 0.405123] iommu: Adding device c250000.i2c to group 8 [ 0.405411] iommu: Adding device 31e0000.i2c to group 9 [ 0.406842] iommu: Adding device 3210000.spi to group 10 [ 0.407130] iommu: Adding device c260000.spi to group 11 [ 0.407767] iommu: Adding device 3100000.serial to group 12 [ 0.408052] iommu: Adding device 3110000.serial to group 13 [ 0.408327] iommu: Adding device c280000.serial to group 14 [ 0.408608] iommu: Adding device 3130000.serial to group 15 [ 0.409760] iommu: Adding device 2490000.ether_qos to group 16 [ 0.409771] arm-smmu: forcing sodev map for 2490000.ether_qos [ 0.410579] iommu: Adding device b000000.rtcpu to group 17 [ 0.412257] iommu: Adding device 13e10000.host1x to group 18 [ 0.412535] iommu: Adding device 13e10000.host1x:ctx0 to group 19 [ 0.412807] iommu: Adding device 13e10000.host1x:ctx1 to group 20 [ 0.413123] iommu: Adding device 13e10000.host1x:ctx2 to group 21 [ 0.413401] iommu: Adding device 13e10000.host1x:ctx3 to group 22 [ 0.413674] iommu: Adding device 13e10000.host1x:ctx4 to group 23 [ 0.413957] iommu: Adding device 13e10000.host1x:ctx5 to group 24 [ 0.414223] iommu: Adding device 13e10000.host1x:ctx6 to group 25 [ 0.414494] iommu: Adding device 13e10000.host1x:ctx7 to group 26 [ 0.414905] iommu: Adding device 150c0000.nvcsi to group 27 [ 0.415458] iommu: Adding device 15700000.vi to group 28 [ 0.415751] iommu: Adding device 15600000.isp to group 29 [ 0.415948] iommu: Adding device 15200000.dc_common to group 30 [ 0.415991] platform 15200000.dc_common: OF IOVA linear map 0x96085000 size (0x140000) [ 0.416008] platform 15200000.dc_common: OF IOVA linear map 0x96081000 size (0x2008) [ 0.416451] iommu: Adding device 15200000.nvdisplay to group 31 [ 0.416768] iommu: Adding device 15210000.nvdisplay to group 32 [ 0.417087] iommu: Adding device 15340000.vic to group 33 [ 0.417294] iommu: Adding device 154c0000.nvenc to group 34 [ 0.417479] iommu: Adding device 15480000.nvdec to group 35 [ 0.417775] iommu: Adding device 15380000.nvjpg to group 36 [ 0.417967] iommu: Adding device 15500000.tsec to group 37 [ 0.418153] iommu: Adding device 15100000.tsecb to group 38 [ 0.419026] iommu: Adding device 15810000.se to group 39 [ 0.419219] iommu: Adding device 15820000.se to group 40 [ 0.419420] iommu: Adding device 15830000.se to group 41 [ 0.419606] iommu: Adding device 15840000.se to group 42 [ 0.420352] iommu: Adding device smmu_test to group 43 [ 0.420914] mc: mapped MMIO address: 0xffffff800a710000 -> 0x2c10000 [ 0.420925] mc: mapped MMIO address: 0xffffff800a730000 -> 0x2c20000 [ 0.420935] mc: mapped MMIO address: 0xffffff800a750000 -> 0x2c30000 [ 0.420945] mc: mapped MMIO address: 0xffffff800a770000 -> 0x2c40000 [ 0.420955] mc: mapped MMIO address: 0xffffff800a790000 -> 0x2c50000 [ 0.420962] nv-tegra-mc 2c10000.mc: No mssnvlink node [ 0.420989] mc-err: mcerr ops are set to t18x [ 0.421130] dram-ecc: DRAM ECC disabled-MC_ECC_CONTROL:0x0000000c [ 0.421879] iommu: Adding device 3530000.xhci to group 44 [ 0.421891] arm-smmu: forcing sodev map for 3530000.xhci [ 0.422287] iommu: Adding device 3550000.xudc to group 45 [ 0.422297] arm-smmu: forcing sodev map for 3550000.xudc [ 0.422813] tegra186-aowake c370000.pmc: WAKE_AOWAKE_CNTRL_83 = 0x10a [ 0.422819] tegra186-aowake c370000.pmc: WAKE_AOWAKE_CTRL_0 = 3 [ 0.422824] tegra186-aowake c370000.pmc: WAKE_AOWAKE_CNTRL_24(PMU_INT) = 256 [ 0.423412] iommu: Adding device 17000000.gp10b to group 46 [ 0.424334] tegra-reset 5000000.clock: registered 193 resets. [ 0.426250] iommu: Adding device d000000.bpmp to group 47 [ 0.426448] bpmp: ping status is 0 [ 0.426527] bpmp d000000.bpmp: firmware tag is 91572a54614f84d0fd0c270beec2c56f [ 0.428156] bpmp d000000.bpmp: probe ok [ 0.430736] iommu: Adding device 2600000.dma to group 48 [ 0.431537] GPIO line 424 (camera-control-output-low) hogged as output/low [ 0.431569] GPIO line 427 (camera-control-output-low) hogged as output/low [ 0.431613] GPIO line 408 (w-disable1) hogged as output/high [ 0.431649] GPIO line 410 (w-disable2) hogged as output/high [ 0.431815] gpiochip_setup_dev: registered GPIOs 320 to 511 on device: gpiochip0 (tegra-gpio) [ 0.435679] gpiochip_setup_dev: registered GPIOs 256 to 319 on device: gpiochip1 (tegra-gpio-aon) [ 0.437281] iommu: Adding device 10003000.pcie-controller to group 49 [ 0.437295] arm-smmu: forcing sodev map for 10003000.pcie-controller [ 0.437588] iommu: Adding device sound to group 50 [ 0.437899] iommu: Adding device 3510000.hda to group 51 [ 0.444600] iommu: Adding device c1a0000.aon to group 52 [ 0.445127] vdd-1v8-ap: 1800 mV [ 0.445334] vdd-ac-bat: 5000 mV [ 0.445518] vdd-3v3-disp-cvb: 3300 mV [ 0.445790] vdd-3v3-cvb: 3300 mV [ 0.445977] vdd-1v8-cvb: 1800 mV [ 0.446163] vdd-fan: 5000 mV [ 0.446343] vdd-hdmi-5v0: 5000 mV [ 0.446519] vdd_sys_en: 1200 mV [ 0.464975] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.467581] eventlib_kernel: keventlib is initialized, test id: 0 [ 0.467774] SCSI subsystem initialized [ 0.467890] libata version 3.00 loaded. [ 0.468037] usbcore: registered new interface driver usbfs [ 0.468068] usbcore: registered new interface driver hub [ 0.468096] usbcore: registered new device driver usb [ 0.470855] random: fast init done [ 0.477493] max77620 4-003c: PMIC Version OTP:0x45 and ES:0x8 [ 0.481240] vddio-ddr: at 1125 mV [ 0.485033] avdd_dsi_csi: 1200 mV [ 0.489072] vdd-1v8: 1800 mV [ 0.493032] vdd-3v3-sys: 3300 mV [ 0.493895] spmic-ldo0: at 1800 mV [ 0.494520] spmic-ldo1: at 800 mV [ 0.497032] vddio-3v3: 3300 mV [ 0.497682] vddio-sdmmc1: 1800 <--> 3300 mV at 3300 mV [ 0.501033] vdd-rtc: at 800 mV [ 0.501698] avdd-ts-hv: 1800 <--> 3300 mV at 1800 mV [ 0.505032] spmic-ldo6: at 800 mV [ 0.509032] vdd-pex-1v00: 1000 mV [ 0.509614] dvdd-pex: 1000 mV [ 0.511584] GPIO line 253 (spmic_gpio_input) hogged as input [ 0.511714] GPIO line 254 (spmic_gpio_input) hogged as input [ 0.511885] gpiochip_setup_dev: registered GPIOs 248 to 255 on device: gpiochip2 (max77620-gpio) [ 0.512065] max77620 4-003c: max77620 probe successful [ 0.512424] media: Linux media interface: v0.10 [ 0.512453] Linux video capture interface: v2.00 [ 0.514675] pps_core: LinuxPPS API ver. 1 registered [ 0.514678] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.514688] PTP clock support registered [ 0.514860] tegra_wdt_t18x 30c0000.watchdog: Expiry count is deprecated [ 0.515041] tegra_wdt_t18x 30c0000.watchdog: Tegra WDT init timeout = 120 sec [ 0.515057] tegra_wdt_t18x 30c0000.watchdog: Registered successfully [ 0.516130] trusty trusty: trusty version: Built: 12:20:14 Jul 26 2021 [ 0.516144] trusty trusty: selected api version: 3 (requested 3) [ 0.517001] Advanced Linux Sound Architecture Driver Initialized. [ 0.517337] Bluetooth: Core ver 2.22 [ 0.517363] NET: Registered protocol family 31 [ 0.517365] Bluetooth: HCI device and connection manager initialized [ 0.517371] Bluetooth: HCI socket layer initialized [ 0.517375] Bluetooth: L2CAP socket layer initialized [ 0.517389] Bluetooth: SCO socket layer initialized [ 0.517935] vdd-sys-bl: 3300 mV [ 0.519466] camchar: rtcpu character device driver loaded [ 0.519886] gpio tegra-gpio wake61 for gpio=92(L:4) [ 0.519959] extcon-gpio-states external-connection:extcon@1: Cable state:0, cable id:0 [ 0.520831] clocksource: Switched to clocksource arch_sys_counter [ 0.543056] VFS: Disk quotas dquot_6.6.0 [ 0.543130] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.543388] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.543812] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000c6000000, size=0x2a000000 [ 0.543917] cma: enabled page replacement for spfn=c6000, epfn=f0000 [ 0.543921] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful [ 0.543929] nvmap: nvmap_select_cache_ops() nvmap cache ops set to roc [ 0.543933] nvmap_page_pool_init: Total RAM pages: 977072 [ 0.543936] nvmap_page_pool_init: nvmap page pool size: 122134 pages (477 MB) [ 0.543992] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.544456] misc nvmap: created heap vpr base 0x00000000c6000000 size (688128KiB) [ 0.546470] tegra-gpcdma 2600000.dma: GPC DMA driver register 32 channels [ 0.552077] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type BCPU-therm [ 0.552267] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type MCPU-therm [ 0.552595] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm [ 0.552669] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [ 0.552833] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die [ 0.553050] la/ptsa driver initialized. [ 0.553059] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz [ 0.553061] pre_t19x_iso_plat_init(): max_iso_bw=23040000KB [ 0.553350] NET: Registered protocol family 2 [ 0.553947] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.554104] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.554404] TCP: Hash tables configured (established 32768 bind 32768) [ 0.554450] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.554509] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.554773] NET: Registered protocol family 1 [ 0.555153] RPC: Registered named UNIX socket transport module. [ 0.555156] RPC: Registered udp transport module. [ 0.555158] RPC: Registered tcp transport module. [ 0.555161] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.555167] PCI: CLS 0 bytes, default 64 [ 0.555278] Trying to unpack rootfs image as initramfs... [ 0.763761] Freeing initrd memory: 7068K [ 0.778302] host1x 13e10000.host1x: initialized [ 0.779532] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.781640] audit: initializing netlink subsys (disabled) [ 0.781665] audit: type=2000 audit(0.672:1): initialized [ 0.782043] workingset: timestamp_bits=46 max_order=20 bucket_order=0 [ 0.788493] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.789472] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.789973] 9p: Installing v9fs 9p2000 file system support [ 0.792083] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240) [ 0.792143] io scheduler noop registered [ 0.792352] io scheduler cfq registered (default) [ 0.795204] gic 2a41000.agic-controller: GIC IRQ controller registered [ 0.809901] iommu: Adding device aconnect@2a41000:adsp_audio to group 53 [ 0.830492] iommu: Adding device 2993000.adsp to group 54 [ 0.831065] tegra-aconnect aconnect@2a41000: Tegra ACONNECT bus registered [ 0.835757] tegra-pwm 3280000.pwm: PWM clk can sleep in ops [ 0.836613] tegra-pwm 3290000.pwm: PWM clk can sleep in ops [ 0.837456] tegra-pwm 32a0000.pwm: PWM clk can sleep in ops [ 0.838238] tegra-pwm c340000.pwm: PWM clk can sleep in ops [ 0.840099] tegra-pcie 10003000.pcie-controller: 2x1, 1x1, 1x1 configuration [ 0.840845] tegra-pcie 10003000.pcie-controller: PCIE: Enable power rails [ 0.841131] tegra-pcie 10003000.pcie-controller: probing port 0, using 2 lanes [ 0.841270] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [ 0.841375] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=1500000, max_bw=1500000 [ 0.843278] tegra-pcie 10003000.pcie-controller: probing port 2, using 1 lanes [ 0.843443] tsec 15500000.tsec: initialized [ 0.844337] tsec 15100000.tsecb: initialized [ 0.846641] nvdec 15480000.nvdec: initialized [ 0.850302] falcon 15340000.vic: initialized [ 0.851436] falcon 154c0000.nvenc: initialized [ 0.852495] falcon 15380000.nvjpg: initialized [ 0.854405] iommu_context_dev 13e10000.host1x:ctx0: initialized (streamid=56) [ 0.855902] iommu_context_dev 13e10000.host1x:ctx1: initialized (streamid=57) [ 0.857446] iommu_context_dev 13e10000.host1x:ctx2: initialized (streamid=58) [ 0.858931] iommu_context_dev 13e10000.host1x:ctx3: initialized (streamid=59) [ 0.860415] iommu_context_dev 13e10000.host1x:ctx4: initialized (streamid=60) [ 0.861896] iommu_context_dev 13e10000.host1x:ctx5: initialized (streamid=61) [ 0.863381] iommu_context_dev 13e10000.host1x:ctx6: initialized (streamid=62) [ 0.864883] iommu_context_dev 13e10000.host1x:ctx7: initialized (streamid=63) [ 0.867382] tegradccommon 15200000.dc_common: host1x channel mapped [ 0.867390] tegradccommon 15200000.dc_common: dc_common syncpt # 1 allocated [ 0.867417] tegradccommon 15200000.dc_common: dma mapping done [ 0.868054] tegradc 15200000.nvdisplay: disp0 connected to head0->/host1x/sor1 [ 0.868091] generic_infoframe_type: 0x87 [ 0.868160] tegradc 15200000.nvdisplay: DT parsed successfully [ 0.868178] tegradc 15200000.nvdisplay: Display dc.ffffff800abe0000 registered with id=0 [ 0.873855] tegra_nvdisp_bandwidth_register_max_config: max config iso bw = 16727000 KB/s [ 0.873859] tegra_nvdisp_bandwidth_register_max_config: max config EMC floor = 665600000 Hz [ 0.873862] tegra_nvdisp_bandwidth_register_max_config: max config hubclk = 357620000 Hz [ 0.874010] tegradc 15200000.nvdisplay: vblank syncpt # 8 for dc 0 [ 0.874015] tegradc 15200000.nvdisplay: vpulse3 syncpt # 9 for dc 0 [ 0.874958] tegradc 15200000.nvdisplay: Bootloader disp_param detected. Detected mode: 640x480 (on 0x0mm) pclk=50347983 [ 0.876910] tegradc 15200000.nvdisplay: hdmi: invalid prod list prod_list_hdmi_board [ 0.876914] tegradc 15200000.nvdisplay: hdmi: tegra_hdmi_tmds_range_read(bd) failed [ 0.879079] tegradc 15200000.nvdisplay: probed [ 0.880230] tegra-adma 2930000.adma: Tegra210 ADMA driver registered 32 channels [ 0.880824] tegra-fuse-burn 3820000.efuse:efuse-burn: shutdown limit check disabled [ 0.880850] tegra-fuse-burn 3820000.efuse:efuse-burn: Fuse burn driver initialized [ 0.881332] kfuse 3830000.kfuse: initialized [ 0.882592] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0 [ 0.885610] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.887680] console [ttyS0] disabled [ 0.887725] 3100000.serial: ttyS0 at MMIO 0x3100000 (irq = 33, base_baud = 25500000) is a Tegra [ 0.887771] console [ttyS0] enabled [ 0.888872] 3110000.serial: ttyTHS1 at MMIO 0x3110000 (irq = 34, base_baud = 0) is a TEGRA_UART [ 0.889548] c280000.serial: ttyTHS2 at MMIO 0xc280000 (irq = 35, base_baud = 0) is a TEGRA_UART [ 0.889708] serial-tegra 3130000.serial: RX in PIO mode [ 0.890292] 3130000.serial: ttyTHS3 at MMIO 0x3130000 (irq = 36, base_baud = 0) is a TEGRA_UART [ 0.890755] Console: switching to colour frame buffer device 80x30 [ 0.890776] tegradc 15200000.nvdisplay: fb registered [ 0.890964] gpio tegra-gpio wake21 for gpio=121(P:1) [ 0.891364] tegra_nvdisp_handle_pd_enable: Unpowergated Head0 pd [ 0.891408] [drm] Initialized [ 0.891418] tegra_nvdisp_handle_pd_enable: Unpowergated Head1 pd [ 0.892447] Parent Clock set for DC plld2 [ 0.898381] brd: module loaded [ 0.904840] loop: module loaded [ 0.904891] tegra_profiler: version: 1.145, samples/io: 49/28 [ 0.904978] tegra_profiler: auth: init [ 0.905593] THERMAL EST: found 3 subdevs [ 0.905598] THERMAL EST num_resources: 0 [ 0.905602] [THERMAL EST subdev 0] [ 0.905607] [THERMAL EST subdev 1] [ 0.905611] [THERMAL EST subdev 2] [ 0.905620] THERMAL EST: Found 2 profiles, default profile is quiet [ 0.905882] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est [ 0.905885] THERMAL EST: thz register success. [ 0.905980] THERMAL EST: end of probe, return err: 0 [ 0.906615] sd: No Scsi addr parsed to reserve index [ 0.906639] hisi_sas: driver version v1.6 [ 0.911376] libphy: Fixed MDIO Bus: probed [ 0.911958] tun: Universal TUN/TAP device driver, 1.6 [ 0.911961] tun: (C) 1999-2004 Max Krasnyansky [ 0.912561] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 0.912563] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.912597] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 0.912599] igb: Copyright (c) 2007-2014 Intel Corporation. [ 0.912630] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.912632] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.912663] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 4.4.0-k [ 0.912665] ixgbe: Copyright (c) 1999-2016 Intel Corporation. [ 0.944039] tegradc 15200000.nvdisplay: hdmi: tmds rate:50349K prod-setting:prod_c_hdmi_0m_54m [ 0.944463] tegradc 15200000.nvdisplay: hdmi: get RGB quant from REG programmed by BL. [ 0.944473] tegradc 15200000.nvdisplay: hdmi: BL set VIC 0 [ 0.944477] tegradc 15200000.nvdisplay: hdmi: get YCC quant from REG programmed by BL. [ 0.944993] tegra-i2c 3190000.i2c: arb lost in communicate to add 0x50 [ 0.945476] extcon-disp-state external-connection:disp-state: cable 47 state 1 [ 0.945479] Extcon AUX1(HDMI) enable [ 0.945846] tegradc 15210000.nvdisplay: disp1 connected to head1->/host1x/sor [ 0.945879] generic_infoframe_type: 0x87 [ 0.945938] tegradc 15210000.nvdisplay: DT parsed successfully [ 0.945960] tegradc 15210000.nvdisplay: Display dc.ffffff800afd0000 registered with id=1 [ 0.946143] tegradc 15210000.nvdisplay: vblank syncpt # 11 for dc 1 [ 0.946149] tegradc 15210000.nvdisplay: vpulse3 syncpt # 12 for dc 1 [ 0.948475] tegradc 15210000.nvdisplay: hdmi: invalid prod list prod_list_hdmi_board [ 0.948479] tegradc 15210000.nvdisplay: hdmi: tegra_hdmi_tmds_range_read(bd) failed [ 0.952101] tegra-i2c 31b0000.i2c: no acknowledge from address 0x50 [ 0.953614] tegradc 15210000.nvdisplay: probed [ 0.953769] tegradc 15210000.nvdisplay: fb registered [ 0.953903] gpio tegra-gpio wake19 for gpio=120(P:0) [ 1.080488] tegradc 15200000.nvdisplay: blank - powerdown [ 1.127931] extcon-disp-state external-connection:disp-state: cable 47 state 0 [ 1.127934] Extcon AUX1(HDMI) disable [ 1.151402] tegra_nvdisp_handle_pd_disable: Powergated Head1 pd [ 1.152303] tegra_nvdisp_handle_pd_disable: Powergated Head0 pd [ 1.157159] eqos 2490000.ether_qos: can't get pllrefe_vcoout clk (-2) [ 1.161148] eqos 2490000.ether_qos: failed to read eqos_auto_cal_config_0_reg [ 1.162155] eqos 2490000.ether_qos: Setting local MAC: 48 b0 2d 56 2 b [ 1.162202] Using phyrst_lpmode = 1 from DT [ 1.162374] libphy: dwc_phy: probed [ 1.166677] PPP generic driver version 2.4.2 [ 1.166951] PPP BSD Compression module registered [ 1.166957] PPP Deflate Compression module registered [ 1.167007] PPP MPPE Compression module registered [ 1.167014] NET: Registered protocol family 24 [ 1.167102] usbcore: registered new interface driver r8152 [ 1.167145] usbcore: registered new interface driver asix [ 1.167200] usbcore: registered new interface driver ax88179_178a [ 1.167240] usbcore: registered new interface driver cdc_ether [ 1.167276] usbcore: registered new interface driver net1080 [ 1.167306] usbcore: registered new interface driver cdc_subset [ 1.167338] usbcore: registered new interface driver zaurus [ 1.167374] usbcore: registered new interface driver simcom_wwan [ 1.167440] usbcore: registered new interface driver cdc_ncm [ 1.167560] usbcore: registered new interface driver qmi_wwan [ 1.167881] VFIO - User Level meta-driver version: 0.3 [ 1.169351] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.169378] ehci-pci: EHCI PCI platform driver [ 1.169417] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.169428] ohci-pci: OHCI PCI platform driver [ 1.169462] ohci-platform: OHCI generic platform driver [ 1.175265] tegra-xusb 3530000.xhci: USB2 port 0 has OTG_CAP [ 1.177714] tegra-xusb 3530000.xhci: extcon 0: ffffffc0ef984400 id [ 1.179518] usbcore: registered new interface driver cdc_wdm [ 1.179857] usbcore: registered new interface driver uas [ 1.179985] usbcore: registered new interface driver usb-storage [ 1.180217] usbcore: registered new interface driver usbserial [ 1.180305] usbcore: registered new interface driver option [ 1.180389] usbserial: USB Serial support registered for GSM modem (1-port) [ 1.180447] tegradc 15200000.nvdisplay: unblank [ 1.181319] tegra-xusb 3530000.xhci: Firmware timestamp: 2020-07-06 13:39:28 UTC, Version: 55.18 release [ 1.181370] tegra-xusb 3530000.xhci: xHCI Host Controller [ 1.181395] tegra-xusb 3530000.xhci: new USB bus registered, assigned bus number 1 [ 1.181661] tegra_nvdisp_handle_pd_enable: Unpowergated Head0 pd [ 1.181809] tegra_nvdisp_handle_pd_enable: Unpowergated Head1 pd [ 1.182314] tegra-xusb 3530000.xhci: hcc params 0x0184fd25 hci version 0x100 quirks 0x00050810 [ 1.182377] tegra-xusb 3530000.xhci: irq 69, io mem 0x03530000 [ 1.182584] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.182589] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.182593] usb usb1: Product: xHCI Host Controller [ 1.182595] usb usb1: Manufacturer: Linux 4.9.253-tegra xhci-hcd [ 1.182597] usb usb1: SerialNumber: 3530000.xhci [ 1.183364] hub 1-0:1.0: USB hub found [ 1.183404] hub 1-0:1.0: 4 ports detected [ 1.183833] tegra-xusb 3530000.xhci: xHCI Host Controller [ 1.183843] tegra-xusb 3530000.xhci: new USB bus registered, assigned bus number 2 [ 1.183971] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.183975] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.183978] usb usb2: Product: xHCI Host Controller [ 1.183981] usb usb2: Manufacturer: Linux 4.9.253-tegra xhci-hcd [ 1.183983] usb usb2: SerialNumber: 3530000.xhci [ 1.184417] hub 2-0:1.0: USB hub found [ 1.184442] hub 2-0:1.0: 3 ports detected [ 1.185562] Parent Clock set for DC plld2 [ 1.185831] Wake76 for irq=199 [ 1.185833] Wake77 for irq=199 [ 1.185834] Wake78 for irq=199 [ 1.185836] Wake79 for irq=199 [ 1.185837] Wake80 for irq=199 [ 1.185838] Wake81 for irq=199 [ 1.185839] Wake82 for irq=199 [ 1.185866] tegra-xusb 3530000.xhci: Upgrade port 0 to USB3.0 [ 1.185871] tegra-xusb 3530000.xhci: Upgrade port 1 to USB3.0 [ 1.188825] tegra-xudc-new 3550000.xudc: device count: 1 [ 1.189513] tegradc 15200000.nvdisplay: hdmi: tmds rate:164340K prod-setting:prod_c_hdmi_111m_223m [ 1.189954] tegra-xudc-new 3550000.xudc: USB charger detection disabled [ 1.189961] tegra-xudc-new 3550000.xudc: vbus state: 0 [ 1.190377] mousedev: PS/2 mouse device common for all mice [ 1.190437] usbcore: registered new interface driver xpad [ 1.190595] tegra-xudc-new 3550000.xudc: entering ELPG [ 1.190735] tegradc 15200000.nvdisplay: hdmi: get YCC quant from EDID. [ 1.191892] tegra-xudc-new 3550000.xudc: entering ELPG done [ 1.225899] extcon-disp-state external-connection:disp-state: cable 47 state 1 [ 1.225901] Extcon AUX1(HDMI) enable [ 1.240875] tegradc 15200000.nvdisplay: sync windows ret = 246 [ 1.267174] extcon-disp-state external-connection:disp-state: cable 51 state 1 [ 1.267177] Extcon HDMI: HPD enabled [ 1.267194] tegradc 15200000.nvdisplay: hdmi: plugged [ 1.278788] tegra-pcie 10003000.pcie-controller: link 2 down, retrying [ 1.284992] usb usb2: usb_suspend_both: status 0 [ 1.317598] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0 [ 1.318664] Wake73 for irq=42 [ 1.319896] rtc rtc1: alarm rtc device [ 1.319907] tegra_rtc c2a0000.rtc: rtc core: registered c2a0000.rtc as rtc1 [ 1.319932] tegra_rtc c2a0000.rtc: Tegra internal Real Time Clock [ 1.320103] i2c /dev entries driver [ 1.321711] i2c i2c-2: Added multiplexed i2c bus 9 [ 1.321996] i2c i2c-2: Added multiplexed i2c bus 10 [ 1.322000] i2c-mux-gpio cam_i2cmux: 2 port mux on 3180000.i2c adapter [ 1.322421] imx219 9-0010: tegracam sensor driver:imx219_v2.0.6 [ 1.345762] tegra-i2c 3180000.i2c: no acknowledge from address 0x10 [ 1.345801] imx219 9-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.353430] imx219 9-0010: board setup failed [ 1.357884] imx219: probe of 9-0010 failed with error -121 [ 1.358172] imx219 10-0010: tegracam sensor driver:imx219_v2.0.6 [ 1.381380] tegra-i2c 3180000.i2c: no acknowledge from address 0x10 [ 1.381427] imx219 10-0010: imx219_board_setup: error during i2c read probe (-121) [ 1.389129] imx219 10-0010: board setup failed [ 1.393661] imx219: probe of 10-0010 failed with error -121 [ 1.394748] pps_core: source pps.-1 got cdev (248:0) [ 1.394754] pps pps0: new PPS source pps.-1 [ 1.394813] pps pps0: Registered IRQ 329 as PPS source [ 1.395154] max77620-power max77620-power: Event recorder REG_NVERC : 0x0 [ 1.399345] parse_throttle_dt_data: Num cap clks = 4 [ 1.399349] parse_throttle_dt_data: clk=mcpu type=1 [ 1.399352] parse_throttle_dt_data: clk=bcpu type=2 [ 1.399359] parse_throttle_dt_data: clk=gpu type=4 [ 1.399362] parse_throttle_dt_data: clk=emc type=3 [ 1.399970] tegra_throttle_probe: probe successful. #cdevs=4 [ 1.400452] FAN dev name: pwm-fan [ 1.400501] FAN:gpio request success. [ 1.400509] FAN: can't find tach_gpio [ 1.400518] pwm_fan_driver pwm-fan: Found 2 profiles, default profile is quiet [ 1.400537] pwm_fan_driver pwm-fan: cap state:4, cap pwm:255 [ 1.400716] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal [ 1.400720] pwm_fan_driver pwm-fan: tach period: 1000 [ 1.401177] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2 [ 1.401182] pwm_fan_driver pwm-fan: index 1: pwm=130, rpm=1000, rru=2, rrd=2, state:2 [ 1.401186] pwm_fan_driver pwm-fan: index 2: pwm=160, rpm=2000, rru=1, rrd=1, state:2 [ 1.401189] pwm_fan_driver pwm-fan: index 3: pwm=200, rpm=3000, rru=1, rrd=1, state:2 [ 1.401193] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3 [ 1.401197] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3 [ 1.401200] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3 [ 1.401204] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4 [ 1.401208] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4 [ 1.401212] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4 [ 1.401700] tegra-oc-event d280000.soctherm-oc-event: OC driver initialized [ 1.402606] device-mapper: uevent: version 1.0.3 [ 1.402921] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com [ 1.403168] CPU EMC frequency mapping table: from device tree [ 1.405075] cpufreq: platform driver Initialization: pass [ 1.405625] cpuidle: Initializing cpuidle driver init for Denver cluster [ 1.405744] cpuidle: Initializing cpuidle driver init for A57 cluster [ 1.406522] sdhci: Secure Digital Host Controller Interface driver [ 1.406523] sdhci: Copyright(c) Pierre Ossman [ 1.406525] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.407447] sdhci-tegra 3460000.sdhci: Client registration for eMC Successful [ 1.408999] CMDQ: cmdq_platfm_init successful [ 1.409432] sdhci-tegra 3440000.sdhci: Got CD GPIO [ 1.409910] CQE: CMD_TIMING bit set for R1B DCMD [ 1.410018] sdhci-tegra 3440000.sdhci: Client registration for eMC Successful [ 1.414437] tegra-se-nvhost 15810000.se: initialized [ 1.415474] tegra-se-nvhost 15810000.se: tegra_se_probe: complete [ 1.416327] tegra-se-nvhost 15820000.se: initialized [ 1.417306] tegra-se-nvhost 15820000.se: tegra_se_probe: complete [ 1.420377] tegra-se-nvhost 15830000.se: initialized [ 1.421184] tegra-se-nvhost 15830000.se: tegra_se_probe: complete [ 1.421601] tegra-se-nvhost 15840000.se: initialized [ 1.422527] tegra-se-nvhost 15840000.se: tegra_se_probe: complete [ 1.423205] tegra-se-elp 3ad0000.se_elp: tegra_se_elp_probe: complete [ 1.423322] hidraw: raw HID events driver (C) Jiri Kosina [ 1.424396] usbcore: registered new interface driver usbhid [ 1.424398] usbhid: USB HID core driver [ 1.429047] tegra186-cam-rtcpu b000000.rtcpu: Trace buffer configured at IOVA=0xbff00000 [ 1.430756] tegra-ivc ivc-b000000.rtcpu: region 0: iova=0xbfef0000-0xbfefdb7f size=56192 [ 1.430978] tegra-ivc ivc-b000000.rtcpu:echo@0: echo: ver=0 grp=1 RX[16x64]=0x1000-0x1480 TX[16x64]=0x1480-0x1900 [ 1.431102] tegra-ivc ivc-b000000.rtcpu:vinotify@12c0: vinotify: ver=0 grp=1 RX[64x128]=0x1900-0x3980 TX[64x128]=0x3980-0x5a00 [ 1.431788] tegra-ivc ivc-b000000.rtcpu:mods@32c0: mods: ver=0 grp=1 RX[1x64]=0x5a00-0x5ac0 TX[1x64]=0x5ac0-0x5b80 [ 1.431858] tegra-ivc ivc-b000000.rtcpu:ivccontrol@52c0: ivccontrol: ver=0 grp=1 RX[16x320]=0x5b80-0x7000 TX[16x320]=0x7000-0x8480 [ 1.431909] tegra-ivc ivc-b000000.rtcpu:ivccapture@72c0: ivccapture: ver=0 grp=1 RX[16x64]=0x8480-0x8900 TX[16x64]=0x8900-0x8d80 [ 1.431959] tegra-ivc ivc-b000000.rtcpu:dbg@7c00: dbg: ver=0 grp=1 RX[1x384]=0x8d80-0x8f80 TX[1x384]=0x8f80-0x9180 [ 1.432061] tegra-ivc ivc-b000000.rtcpu:dbg@7e00: dbg: ver=0 grp=1 RX[1x8192]=0x9180-0xb200 TX[1x8192]=0xb200-0xd280 [ 1.432351] tegra186-cam-rtcpu b000000.rtcpu: using cam RTCPU IRQ (49) [ 1.432354] tegra186-cam-rtcpu b000000.rtcpu: tegra_camrtc_mon_create is successful [ 1.432862] tegra186-cam-rtcpu b000000.rtcpu: firmware version cpu=sce cmd=5 sha1=c73bbe92930645be44530c166eb578bfbb9499c3 [ 1.434446] tegra_aon c1a0000.aon: tegra aon driver probe OK [ 1.434845] tegra186-aondbg aondbg: aondbg driver probe() OK [ 1.435242] register_ari_mca_banks: Registered MCA ROC:IOB [ 1.435557] register_ari_mca_banks: Registered MCA ROC:CCE [ 1.436293] tegra18-bridge 2390000.axi2apb: axi_cbb clk rate = 102 MHZ, timeout = 97000 useconds [ 1.436295] tegra18-bridge 2390000.axi2apb: enabled timeout = 9894000 [ 1.436298] tegra18-bridge 2390000.axi2apb: bridge probed OK [ 1.436344] tegra18-bridge 23a0000.axi2apb: axi_cbb clk rate = 102 MHZ, timeout = 97000 useconds [ 1.436346] tegra18-bridge 23a0000.axi2apb: enabled timeout = 9894000 [ 1.436349] tegra18-bridge 23a0000.axi2apb: bridge probed OK [ 1.436390] tegra18-bridge 23b0000.axi2apb: axi_cbb clk rate = 102 MHZ, timeout = 97000 useconds [ 1.436393] tegra18-bridge 23b0000.axi2apb: enabled timeout = 9894000 [ 1.436394] tegra18-bridge 23b0000.axi2apb: bridge probed OK [ 1.436436] tegra18-bridge 23c0000.axi2apb: axi_cbb clk rate = 102 MHZ, timeout = 97000 useconds [ 1.436438] tegra18-bridge 23c0000.axi2apb: enabled timeout = 9894000 [ 1.436440] tegra18-bridge 23c0000.axi2apb: bridge probed OK [ 1.436484] tegra18-bridge 23d0000.axi2apb: axi_cbb clk rate = 102 MHZ, timeout = 97000 useconds [ 1.436486] tegra18-bridge 23d0000.axi2apb: enabled timeout = 9894000 [ 1.436488] tegra18-bridge 23d0000.axi2apb: bridge probed OK [ 1.436529] tegra18-bridge 2100000.axip2p: axi_cbb clk rate = 102 MHZ, timeout = 97000 useconds [ 1.436533] tegra18-bridge 2100000.axip2p: enabled timeout = 9894000 [ 1.436535] tegra18-bridge 2100000.axip2p: bridge probed OK [ 1.436577] tegra18-bridge 2110000.axip2p: axi_cbb clk rate = 102 MHZ, timeout = 97000 useconds [ 1.436581] tegra18-bridge 2110000.axip2p: enabled timeout = 9894000 [ 1.436584] tegra18-bridge 2110000.axip2p: bridge probed OK [ 1.436624] tegra18-bridge 2120000.axip2p: axi_cbb clk rate = 102 MHZ, timeout = 97000 useconds [ 1.436629] tegra18-bridge 2120000.axip2p: enabled timeout = 9894000 [ 1.436631] tegra18-bridge 2120000.axip2p: bridge probed OK [ 1.436675] tegra18-bridge 2130000.axip2p: axi_cbb clk rate = 102 MHZ, timeout = 97000 useconds [ 1.436680] tegra18-bridge 2130000.axip2p: enabled timeout = 9894000 [ 1.436682] tegra18-bridge 2130000.axip2p: bridge probed OK [ 1.436722] tegra18-bridge 2140000.axip2p: axi_cbb clk rate = 102 MHZ, timeout = 97000 useconds [ 1.436724] tegra18-bridge 2140000.axip2p: enabled timeout = 9894000 [ 1.436726] tegra18-bridge 2140000.axip2p: bridge probed OK [ 1.436811] tegra18-bridge 2150000.axip2p: axi_cbb clk rate = 102 MHZ, timeout = 97000 useconds [ 1.436816] tegra18-bridge 2150000.axip2p: enabled timeout = 9894000 [ 1.436818] tegra18-bridge 2150000.axip2p: bridge probed OK [ 1.436865] tegra18-bridge 2160000.axip2p: axi_cbb clk rate = 102 MHZ, timeout = 97000 useconds [ 1.436871] tegra18-bridge 2160000.axip2p: enabled timeout = 9894000 [ 1.436873] tegra18-bridge 2160000.axip2p: bridge probed OK [ 1.436924] tegra18-bridge 2170000.axip2p: axi_cbb clk rate = 102 MHZ, timeout = 97000 useconds [ 1.436929] tegra18-bridge 2170000.axip2p: enabled timeout = 9894000 [ 1.436931] tegra18-bridge 2170000.axip2p: bridge probed OK [ 1.436974] tegra18-bridge 2180000.axip2p: axi_cbb clk rate = 102 MHZ, timeout = 97000 useconds [ 1.436980] tegra18-bridge 2180000.axip2p: enabled timeout = 9894000 [ 1.436982] tegra18-bridge 2180000.axip2p: bridge probed OK [ 1.437022] tegra18-bridge 2190000.axip2p: axi_cbb clk rate = 102 MHZ, timeout = 97000 useconds [ 1.437026] tegra18-bridge 2190000.axip2p: enabled timeout = 9894000 [ 1.437028] tegra18-bridge 2190000.axip2p: bridge probed OK [ 1.437079] **** A57 ECC: Enabled [ 1.437082] tegra18_a57_serr_init: on CPU 3 a A57 Core [ 1.437141] tegra18x_actmon d230000.actmon: in actmon_register()... [ 1.437500] tegra18x_actmon d230000.actmon: initialization Completed for the device mc_all [ 1.437867] hw perfevents: enabled with denver15_uncore_pmu PMU driver, 3 counters available [ 1.437975] denver_knobs_init:MTS_VERSION:53679346 [ 1.439593] nvpmodel: initialized successfully [ 1.440339] trusty-virtio trusty:virtio: initializing [ 1.440434] trusty_ipc virtio0: vring0: va(pa) ffffffc0eb3c8000(0) qsz 32 notifyid 1 [ 1.440440] trusty_ipc virtio0: vring1: va(pa) ffffffc0eb3ca000(0) qsz 32 notifyid 2 [ 1.440500] trusty-virtio trusty:virtio: initializing done [ 1.440588] trusty_ipc virtio0: is online [ 1.441487] usbcore: registered new interface driver snd-usb-audio [ 1.452812] mmc0: SDHCI controller on 3460000.sdhci [3460000.sdhci] using ADMA 64-bit with 64 bit addr [ 1.460288] input: tegra-hda HDMI/DP,pcm=3 as /devices/3510000.hda/sound/card0/input0 [ 1.460407] input: tegra-hda HDMI/DP,pcm=7 as /devices/3510000.hda/sound/card0/input1 [ 1.464952] mmc1: SDHCI controller on 3440000.sdhci [3440000.sdhci] using ADMA 64-bit with 64 bit addr [ 1.468366] OPE platform probe [ 1.468433] OPE platform probe successful [ 1.494470] mmc0: mmc_decode_ext_csd: CMDQ supported: depth: 31, cmdq_support: 1 [ 1.508596] mmc0: periodic cache flush enabled [ 1.508604] mmc0: new HS400 Enhanced strobe MMC card at address 0001 [ 1.508790] usb 1-2: new high-speed USB device number 2 using tegra-xusb [ 1.508947] mmcblk0: mmc0:0001 DG4016 14.7 GiB [ 1.513082] mmcblk0boot0: mmc0:0001 DG4016 partition 1 4.00 MiB [ 1.516560] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok [ 1.516631] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok [ 1.516700] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok [ 1.516787] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok [ 1.516858] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok [ 1.516924] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok [ 1.516993] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok [ 1.517060] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok [ 1.517128] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok [ 1.517197] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok [ 1.517219] mmcblk0boot1: mmc0:0001 DG4016 partition 2 4.00 MiB [ 1.517274] tegra-asoc: sound: ADMAIF11 <-> ADMAIF11 mapping ok [ 1.517344] tegra-asoc: sound: ADMAIF12 <-> ADMAIF12 mapping ok [ 1.517412] tegra-asoc: sound: ADMAIF13 <-> ADMAIF13 mapping ok [ 1.517477] tegra-asoc: sound: ADMAIF14 <-> ADMAIF14 mapping ok [ 1.517544] tegra-asoc: sound: ADMAIF15 <-> ADMAIF15 mapping ok [ 1.517611] tegra-asoc: sound: ADMAIF16 <-> ADMAIF16 mapping ok [ 1.517678] tegra-asoc: sound: ADMAIF17 <-> ADMAIF17 mapping ok [ 1.517746] tegra-asoc: sound: ADMAIF18 <-> ADMAIF18 mapping ok [ 1.517814] tegra-asoc: sound: ADMAIF19 <-> ADMAIF19 mapping ok [ 1.517882] tegra-asoc: sound: ADMAIF20 <-> ADMAIF20 mapping ok [ 1.521448] mmcblk0rpmb: mmc0:0001 DG4016 partition 3 4.00 MiB [ 1.526274] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 p29 p30 p31 p32 p33 [ 1.529277] usb 1-2: New USB device found, idVendor=0451, idProduct=8342 [ 1.529282] usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=1 [ 1.529285] usb 1-2: SerialNumber: 89000089BBD6 [ 1.529944] hub 1-2:1.0: USB hub found [ 1.530003] hub 1-2:1.0: 5 ports detected [ 1.543369] u32 classifier [ 1.543371] Actions configured [ 1.543430] Initializing XFRM netlink socket [ 1.543963] NET: Registered protocol family 10 [ 1.544528] NET: Registered protocol family 17 [ 1.544538] NET: Registered protocol family 15 [ 1.544596] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.544637] Bluetooth: RFCOMM socket layer initialized [ 1.544645] Bluetooth: RFCOMM ver 1.11 [ 1.544649] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.544655] Bluetooth: HIDP socket layer initialized [ 1.544669] 9pnet: Installing 9P2000 support [ 1.544701] Key type dns_resolver registered [ 1.545119] Registered cp15_barrier emulation handler [ 1.545134] Registered setend emulation handler [ 1.545963] registered taskstats version 1 [ 1.548375] isp 15600000.isp: initialized [ 1.551423] nvcsi 150c0000.nvcsi: initialized [ 1.552344] tegra-vi4 15700000.vi: using default number of vi channels,15 [ 1.554881] Wake83 for irq=51 [ 1.554962] gpio tegra-gpio-aon wake29 for gpio=56(FF:0) [ 1.555115] input: gpio-keys as /devices/gpio-keys/input/input2 [ 1.556241] tegra-vi4 15700000.vi: initialized [ 1.557085] tegra-vi4 15700000.vi: subdev 150c0000.nvcsi--2 bound [ 1.557166] tegra-vi4 15700000.vi: subdev 150c0000.nvcsi--1 bound [ 1.585448] tegra_rtc c2a0000.rtc: setting system clock to 2000-01-01 01:00:09 UTC (946688409) [ 1.586246] mmcblk mmc0:0001: Card claimed for testing. [ 1.603891] bpmp: mounted debugfs mirror [ 1.604721] bwmgr: missing cdev-type property [ 1.608669] ALSA device list: [ 1.608672] #0: tegra-hda at 0x3518000 irq 382 [ 1.608674] #1: tegra-snd-t186ref-mobile-rt565x [ 1.610981] Freeing unused kernel memory: 8640K [ 1.632329] Root device found: mmcblk0p1 [ 1.633458] Found dev node: /dev/mmcblk0p1 [ 1.649105] usb 2-2: new SuperSpeed USB device number 2 using tegra-xusb [ 1.673285] usb 2-2: New USB device found, idVendor=0451, idProduct=8340 [ 1.673290] usb 2-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 1.675050] hub 2-2:1.0: USB hub found [ 1.675443] hub 2-2:1.0: 4 ports detected [ 1.696788] tegra-pcie 10003000.pcie-controller: link 2 down, retrying [ 1.743499] EXT4-fs (mmcblk0p1): 15 orphan inodes deleted [ 1.743502] EXT4-fs (mmcblk0p1): recovery complete [ 1.750024] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 1.751860] Rootfs mounted over mmcblk0p1 [ 1.765852] Switching from initrd to actual rootfs [ 1.790161] pps pps0: PPS event at 946688409.704725120 [ 1.790166] pps pps0: capture assert seq #1 [ 1.792792] usb 1-3: new full-speed USB device number 3 using tegra-xusb [ 1.814541] usb 1-3: New USB device found, idVendor=8087, idProduct=0a2b [ 1.814545] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 1.832790] usb 2-2: usb_suspend_both: status 0 [ 1.833023] usb usb2: usb_suspend_both: status 0 [ 1.863131] systemd[1]: System time before build time, advancing clock. [ 1.881208] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.889953] cgroup: cgroup2: unknown option "nsdelegate" [ 1.896789] usb 1-2.1: new high-speed USB device number 4 using tegra-xusb [ 1.906645] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [ 1.907383] systemd[1]: Detected architecture arm64. [ 1.925785] systemd[1]: Set hostname to . [ 1.935768] usb 1-2.1: New USB device found, idVendor=1e0e, idProduct=9001 [ 1.935772] usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 1.935775] usb 1-2.1: Product: SimTech, Incorporated [ 1.935777] usb 1-2.1: Manufacturer: SimTech, Incorporated [ 1.935780] usb 1-2.1: SerialNumber: 0123456789ABCDEF [ 1.938120] option 1-2.1:1.0: GSM modem (1-port) converter detected [ 1.938295] usb 1-2.1: GSM modem (1-port) converter now attached to ttyUSB0 [ 1.938486] option 1-2.1:1.1: GSM modem (1-port) converter detected [ 1.938603] usb 1-2.1: GSM modem (1-port) converter now attached to ttyUSB1 [ 1.938790] option 1-2.1:1.2: GSM modem (1-port) converter detected [ 1.938908] usb 1-2.1: GSM modem (1-port) converter now attached to ttyUSB2 [ 1.939105] option 1-2.1:1.3: GSM modem (1-port) converter detected [ 1.939225] usb 1-2.1: GSM modem (1-port) converter now attached to ttyUSB3 [ 1.939427] option 1-2.1:1.4: GSM modem (1-port) converter detected [ 1.939542] usb 1-2.1: GSM modem (1-port) converter now attached to ttyUSB4 [ 1.940489] simcom_wwan 1-2.1:1.5: cdc-wdm0: USB WDM device [ 1.940492] simcom(wxb fixed) usbnet bind here [ 1.941551] simcom_wwan 1-2.1:1.5 wwan0: register 'simcom_wwan' at usb-3530000.xhci-2.1, SIMCOM wwan/QMI device, ba:c6:a4:bf:90:ab [ 2.018555] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 2.018563] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 2.020796] usb 1-2.4: new full-speed USB device number 5 using tegra-xusb [ 2.045329] usb 1-2.4: New USB device found, idVendor=046d, idProduct=c52b [ 2.045334] usb 1-2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.045336] usb 1-2.4: Product: USB Receiver [ 2.045339] usb 1-2.4: Manufacturer: Logitech [ 2.102849] tegra-pcie 10003000.pcie-controller: link 2 down, retrying [ 2.104869] tegra-pcie 10003000.pcie-controller: link 2 down, ignoring [ 2.136788] usb 1-2.5: new high-speed USB device number 6 using tegra-xusb [ 2.150164] random: systemd: uninitialized urandom read (16 bytes read) [ 2.151596] systemd[1]: Created slice System Slice. [ 2.151876] random: systemd: uninitialized urandom read (16 bytes read) [ 2.151976] systemd[1]: Listening on Journal Audit Socket. [ 2.152001] random: systemd: uninitialized urandom read (16 bytes read) [ 2.152673] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 2.152909] systemd[1]: Listening on Journal Socket. [ 2.156999] systemd[1]: Starting Load Kernel Modules... [ 2.157183] usb 1-2.5: New USB device found, idVendor=0451, idProduct=82ff [ 2.157186] usb 1-2.5: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.158854] hid-generic 0003:0451:82FF.0004: hidraw0: USB HID v1.11 Device [HID 0451:82ff] on usb-3530000.xhci-2.5/input0 [ 2.192700] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null) [ 2.210671] tegra-pcie 10003000.pcie-controller: PCI host bridge to bus 0000:00 [ 2.210676] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.210680] pci_bus 0000:00: root bus resource [mem 0x40100000-0x47ffffff] [ 2.210683] pci_bus 0000:00: root bus resource [mem 0x48000000-0x7fffffff pref] [ 2.210686] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.210714] pci 0000:00:01.0: [10de:10e5] type 01 class 0x060400 [ 2.210829] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 2.210994] iommu: Adding device 0000:00:01.0 to group 55 [ 2.211002] arm-smmu: forcing sodev map for 0000:00:01.0 [ 2.211074] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.211232] pci 0000:01:00.0: [8086:24fd] type 00 class 0x028000 [ 2.211310] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit] [ 2.211708] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 2.211964] iommu: Adding device 0000:01:00.0 to group 56 [ 2.211969] arm-smmu: forcing sodev map for 0000:01:00.0 [ 2.220978] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.221037] pci 0000:00:01.0: BAR 14: assigned [mem 0x40100000-0x401fffff] [ 2.221049] pci 0000:01:00.0: BAR 0: assigned [mem 0x40100000-0x40101fff 64bit] [ 2.221089] pci 0000:00:01.0: PCI bridge to [bus 01] [ 2.221097] pci 0000:00:01.0: bridge window [mem 0x40100000-0x401fffff] [ 2.221771] pcieport 0000:00:01.0: Signaling PME through PCIe PME interrupt [ 2.221774] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 2.221781] pcie_pme 0000:00:01.0:pcie001: service driver pcie_pme loaded [ 2.221869] aer 0000:00:01.0:pcie002: service driver aer loaded [ 2.408794] random: crng init done [ 2.412223] random: 7 urandom warning(s) missed due to ratelimiting [ 2.481777] squashfs: SQUASHFS error: Xattrs in filesystem, these will be ignored [ 2.493050] squashfs: SQUASHFS error: unable to read xattr id index table [ 2.578995] systemd-journald[2272]: Received request to flush runtime journal from PID 1 [ 2.664941] Intel(R) Wireless WiFi driver for Linux [ 2.664945] Copyright(c) 2003- 2015 Intel Corporation [ 2.665255] iwlwifi 0000:01:00.0: enabling device (0000 -> 0002) [ 2.669915] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-26.ucode failed with error -2 [ 2.679539] iwlwifi 0000:01:00.0: Falling back to user helper [ 2.790169] pps pps0: PPS event at 1639127749.927060608 [ 2.790175] pps pps0: capture assert seq #2 [ 3.181274] using random self ethernet address [ 3.192539] using random host ethernet address [ 3.790180] pps pps0: PPS event at 1663238446.953642960 [ 3.790187] pps pps0: capture assert seq #3 [ 3.953650] Mass Storage Function, version: 2009/09/11 [ 3.953656] LUN: removable file: (no medium) [ 3.967485] using random self ethernet address [ 3.982177] using random host ethernet address [ 4.078390] rndis0: HOST MAC 46:a2:7f:d5:04:40 [ 4.081075] rndis0: MAC 46:a2:7f:d5:04:41 [ 4.083164] usb0: HOST MAC 46:a2:7f:d5:04:42 [ 4.083289] usb0: MAC 46:a2:7f:d5:04:43 [ 4.083309] tegra-xudc-new 3550000.xudc: exiting ELPG [ 4.087710] tegra-xudc-new 3550000.xudc: exiting ELPG done [ 4.087733] tegra-xudc-new 3550000.xudc: ep 0 (type: 0, dir: out) enabled [ 4.087765] tegra-xudc-new 3550000.xudc: entering ELPG [ 4.088416] tegra-xudc-new 3550000.xudc: entering ELPG done [ 4.088431] tegra-xudc-new 3550000.xudc: exiting ELPG [ 4.089382] tegra-xudc-new 3550000.xudc: exiting ELPG done [ 4.089396] tegra-xudc-new 3550000.xudc: entering ELPG [ 4.089921] tegra-xudc-new 3550000.xudc: entering ELPG done [ 4.096599] l4tbr0: port 1(rndis0) entered blocking state [ 4.096604] l4tbr0: port 1(rndis0) entered disabled state [ 4.100953] device rndis0 entered promiscuous mode [ 4.114052] IPv6: ADDRCONF(NETDEV_UP): rndis0: link is not ready [ 4.124255] l4tbr0: port 2(usb0) entered blocking state [ 4.124260] l4tbr0: port 2(usb0) entered disabled state [ 4.124408] device usb0 entered promiscuous mode [ 4.141188] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-25.ucode failed with error -2 [ 4.147184] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready [ 4.151527] iwlwifi 0000:01:00.0: Falling back to user helper [ 4.497343] CPU1: shutdown [ 4.500097] psci: CPU1 killed (polled 0 ms) [ 4.578571] CPU2: shutdown [ 4.582158] psci: CPU2 killed (polled 0 ms) [ 4.790188] pps pps0: PPS event at 1663238447.953650992 [ 4.790194] pps pps0: capture assert seq #4 [ 4.862176] zram: Added device: zram0 [ 4.867505] zram: Added device: zram1 [ 4.874289] zram: Added device: zram2 [ 4.880794] zram: Added device: zram3 [ 4.946930] zram0: detected capacity change from 0 to 502272000 [ 5.079063] Adding 490496k swap on /dev/zram0. Priority:5 extents:1 across:490496k SS [ 5.105574] zram1: detected capacity change from 0 to 502272000 [ 5.160034] Adding 490496k swap on /dev/zram1. Priority:5 extents:1 across:490496k SS [ 5.170047] zram2: detected capacity change from 0 to 502272000 [ 5.200731] Adding 490496k swap on /dev/zram2. Priority:5 extents:1 across:490496k SS [ 5.236673] zram3: detected capacity change from 0 to 502272000 [ 5.238748] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 5.258522] Adding 490496k swap on /dev/zram3. Priority:5 extents:1 across:490496k SS [ 5.410177] bcpu-throttle-alert cooling device registered. [ 5.413472] mcpu-throttle-alert cooling device registered. [ 5.413713] gpu-throttle-alert cooling device registered. [ 5.468831] usbcore: registered new interface driver btusb [ 5.475050] Bluetooth: hci0: Bootloader revision 0.0 build 26 week 38 2015 [ 5.475796] Bluetooth: hci0: Device revision is 16 [ 5.475800] Bluetooth: hci0: Secure boot is enabled [ 5.475802] Bluetooth: hci0: OTP lock is enabled [ 5.475804] Bluetooth: hci0: API lock is enabled [ 5.475806] Bluetooth: hci0: Debug lock is disabled [ 5.475808] Bluetooth: hci0: Minimum firmware build 1 week 10 2014 [ 5.483597] Bluetooth: hci0: Found device firmware: intel/ibt-12-16.sfi [ 5.553840] gpio tegra-gpio-aon wake51 for gpio=47(AA:7) [ 5.556726] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 5.602656] logitech-djreceiver 0003:046D:C52B.0003: hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-3530000.xhci-2.4/input2 [ 5.653838] Bridge firewalling registered [ 5.657581] usb_wwan: exports duplicate symbol usb_wwan_chars_in_buffer (owned by kernel) [ 5.711881] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 5.718274] usb_wwan: exports duplicate symbol usb_wwan_chars_in_buffer (owned by kernel) [ 5.782447] usb_wwan: exports duplicate symbol usb_wwan_chars_in_buffer (owned by kernel) [ 5.790192] pps pps0: PPS event at 1663238448.953656144 [ 5.790196] pps pps0: capture assert seq #5 [ 5.841846] usb_wwan: exports duplicate symbol usb_wwan_chars_in_buffer (owned by kernel) [ 5.941886] usb_wwan: exports duplicate symbol usb_wwan_chars_in_buffer (owned by kernel) [ 5.993215] usb_wwan: exports duplicate symbol usb_wwan_chars_in_buffer (owned by kernel) [ 6.074944] usb_wwan: exports duplicate symbol usb_wwan_chars_in_buffer (owned by kernel) [ 6.145520] usb_wwan: exports duplicate symbol usb_wwan_chars_in_buffer (owned by kernel) [ 6.197755] usb_wwan: exports duplicate symbol usb_wwan_chars_in_buffer (owned by kernel) [ 6.254387] usb_wwan: exports duplicate symbol usb_wwan_chars_in_buffer (owned by kernel) [ 6.317474] usb_wwan: exports duplicate symbol usb_wwan_chars_in_buffer (owned by kernel) [ 6.365450] usb_wwan: exports duplicate symbol usb_wwan_chars_in_buffer (owned by kernel) [ 6.413140] usb_wwan: exports duplicate symbol usb_wwan_chars_in_buffer (owned by kernel) [ 6.473587] usb_wwan: exports duplicate symbol usb_wwan_chars_in_buffer (owned by kernel) [ 6.512181] Netfilter messages via NETLINK v0.30. [ 6.514174] ctnetlink v0.93: registering with nfnetlink. [ 6.541638] usb_wwan: exports duplicate symbol usb_wwan_chars_in_buffer (owned by kernel) [ 6.583142] tegradc 15200000.nvdisplay: unblank [ 6.583151] tegradc 15210000.nvdisplay: blank - powerdown [ 6.601761] usb_wwan: exports duplicate symbol usb_wwan_chars_in_buffer (owned by kernel) [ 6.678901] usb_wwan: exports duplicate symbol usb_wwan_chars_in_buffer (owned by kernel) [ 6.693186] cdc_wdm: exports duplicate symbol usb_cdc_wdm_register (owned by kernel) [ 6.790202] pps pps0: PPS event at 1663238449.953664688 [ 6.790205] pps pps0: capture assert seq #6 [ 6.931613] usb_wwan: exports duplicate symbol usb_wwan_chars_in_buffer (owned by kernel) [ 7.224156] IPv6: ADDRCONF(NETDEV_UP): docker0: link is not ready [ 7.264966] Bluetooth: hci0: Waiting for firmware download to complete [ 7.265775] Bluetooth: hci0: Firmware loaded in 1754740 usecs [ 7.265899] Bluetooth: hci0: Waiting for device to boot [ 7.282803] Bluetooth: hci0: Device booted in 16557 usecs [ 7.284426] Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-12-16.ddc [ 7.286780] Bluetooth: hci0: Applying Intel DDC parameters completed [ 7.790213] pps pps0: PPS event at 1663238450.953676528 [ 7.790219] pps pps0: capture assert seq #7 [ 8.007582] eqos 2490000.ether_qos eth0: Link is Up - 100Mbps/Full - flow control off [ 8.009076] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 8.790216] pps pps0: PPS event at 1663238451.953678608 [ 8.790222] pps pps0: capture assert seq #8 [ 9.790226] pps pps0: PPS event at 1663238452.953690416 [ 9.790232] pps pps0: capture assert seq #9 [ 10.132247] eqos 2490000.ether_qos eth0: Link is Down [ 10.373873] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-24.ucode failed with error -2 [ 10.383180] iwlwifi 0000:01:00.0: Falling back to user helper [ 10.646602] input: Logitech K400 Plus as /devices/3530000.xhci/usb1/1-2/1-2.4/1-2.4:1.2/0003:046D:C52B.0003/0003:046D:404D.0005/input/input3 [ 10.649864] logitech-hidpp-device 0003:046D:404D.0005: input,hidraw2: USB HID v1.11 Keyboard [Logitech K400 Plus] on usb-3530000.xhci-2.4:1 [ 10.676264] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 10.676274] Bluetooth: BNEP socket layer initialized [ 10.790231] pps pps0: PPS event at 1663238453.953695056 [ 10.790237] pps pps0: capture assert seq #10 [ 10.929068] iwlwifi 0000:01:00.0: Direct firmware load for iwlwifi-8265-23.ucode failed with error -2 [ 10.940170] iwlwifi 0000:01:00.0: Falling back to user helper [ 10.989620] iwlwifi 0000:01:00.0: loaded firmware version 22.391740.0 op_mode iwlmvm [ 11.039768] iwlwifi 0000:01:00.0: Detected Intel(R) Dual Band Wireless AC 8265, REV=0x230 [ 11.041902] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled [ 11.042584] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled [ 11.161027] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs' [ 11.161692] thermal thermal_zone6: failed to read out thermal zone (-5) [ 11.168597] thermal thermal_zone6: Registering thermal zone thermal_zone6 for type iwlwifi_1 [ 11.247883] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 11.790236] pps pps0: PPS event at 1663238454.953700848 [ 11.790242] pps pps0: capture assert seq #11 [ 12.077003] fuse init (API version 7.26) [ 12.790245] pps pps0: PPS event at 1663238455.953708272 [ 12.790251] pps pps0: capture assert seq #12 [ 13.790284] pps pps0: PPS event at 1663238456.953726224 [ 13.790307] pps pps0: capture assert seq #13 [ 14.790289] pps pps0: PPS event at 1663238457.953732656 [ 14.790310] pps pps0: capture assert seq #14 [ 15.790304] pps pps0: PPS event at 1663238458.953747632 [ 15.790326] pps pps0: capture assert seq #15 [ 16.790277] pps pps0: PPS event at 1663238459.953740304 [ 16.790283] pps pps0: capture assert seq #16 [ 16.920311] eqos 2490000.ether_qos eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 17.790280] pps pps0: PPS event at 1663238460.953746128 [ 17.790285] pps pps0: capture assert seq #17 [ 18.790293] pps pps0: PPS event at 1663238461.953755632 [ 18.790299] pps pps0: capture assert seq #18 [ 19.790312] pps pps0: PPS event at 1663238462.953768368 [ 19.790322] pps pps0: capture assert seq #19 [ 20.790318] pps pps0: PPS event at 1663238463.953782704 [ 20.790324] pps pps0: capture assert seq #20 [ 21.790317] pps pps0: PPS event at 1663238464.953779536 [ 21.790322] pps pps0: capture assert seq #21 [ 22.790320] pps pps0: PPS event at 1663238465.953784304 [ 22.790326] pps pps0: capture assert seq #22 [ 23.790338] pps pps0: PPS event at 1663238466.953795056 [ 23.790350] pps pps0: capture assert seq #23 [ 24.462093] tegradc 15200000.nvdisplay: unblank [ 24.462101] tegradc 15210000.nvdisplay: blank - powerdown [ 24.790338] pps pps0: PPS event at 1663238467.953802288 [ 24.790344] pps pps0: capture assert seq #24 [ 25.790343] pps pps0: PPS event at 1663238468.953807792 [ 25.790347] pps pps0: capture assert seq #25 [ 26.790350] pps pps0: PPS event at 1663238469.953814320 [ 26.790355] pps pps0: capture assert seq #26 [ 27.790357] pps pps0: PPS event at 1663238470.953822608 [ 27.790362] pps pps0: capture assert seq #27 [ 28.790396] pps pps0: PPS event at 1663238471.953839280 [ 28.790417] pps pps0: capture assert seq #28 [ 29.790404] pps pps0: PPS event at 1663238472.953847152 [ 29.790426] pps pps0: capture assert seq #29 [ 30.790382] pps pps0: PPS event at 1663238473.953845616 [ 30.790387] pps pps0: capture assert seq #30 [ 31.790412] pps pps0: PPS event at 1663238474.953862576 [ 31.790428] pps pps0: capture assert seq #31 [ 31.817382] vdd-3v3-disp-cvb: disabling [ 31.817396] vdd-3v3-cvb: disabling [ 31.817406] vdd-1v8-cvb: disabling [ 31.817416] vdd-fan: disabling [ 31.817427] vdd_sys_en: disabling [ 31.817451] spmic-ldo1: disabling [ 31.817679] vddio-sdmmc1: disabling [ 31.817862] vdd-sys-bl: disabling [ 32.790414] pps pps0: PPS event at 1663238475.953864496 [ 32.790431] pps pps0: capture assert seq #32 [ 33.790436] pps pps0: PPS event at 1663238476.953878640 [ 33.790458] pps pps0: capture assert seq #33 [ 34.790442] pps pps0: PPS event at 1663238477.953884112 [ 34.790465] pps pps0: capture assert seq #34 [ 35.790453] pps pps0: PPS event at 1663238478.953893936 [ 35.790476] pps pps0: capture assert seq #35 [ 36.790440] pps pps0: PPS event at 1663238479.953894832 [ 36.790452] pps pps0: capture assert seq #36 [ 37.790456] pps pps0: PPS event at 1663238480.953906512 [ 37.790472] pps pps0: capture assert seq #37 [ 38.790473] pps pps0: PPS event at 1663238481.953917904 [ 38.790496] pps pps0: capture assert seq #38 [ 39.790486] pps pps0: PPS event at 1663238482.953927344 [ 39.790509] pps pps0: capture assert seq #39 [ 40.790461] pps pps0: PPS event at 1663238483.953923920 [ 40.790466] pps pps0: capture assert seq #40 [ 41.790472] pps pps0: PPS event at 1663238484.953931312 [ 41.790479] pps pps0: capture assert seq #41 [ 42.790475] pps pps0: PPS event at 1663238485.953938448 [ 42.790481] pps pps0: capture assert seq #42 [ 43.790484] pps pps0: PPS event at 1663238486.953947472 [ 43.790490] pps pps0: capture assert seq #43 [ 44.790491] pps pps0: PPS event at 1663238487.953954768 [ 44.790498] pps pps0: capture assert seq #44