àÿâ [0000.096] I> MB1 (prd-version: 1.0.0.0-t194-41334769-a3872862) [0000.102] I> Boot-mode: L0 coldboot [0000.105] I> chip revision : A02P [0000.108] I> Bootrom patch version : 15 (correctly patched) [0000.113] I> ATE fuse revision : 0x200 [0000.117] I> Ram repair fuse : 0x1 [0000.120] I> Ram Code : 0x2 [0000.122] I> rst_source : 0x0 [0000.125] I> rst_level : 0x0 [0000.128] I> Boot-device: eMMC [0000.131] W> DEVICE_PROD: device prod is not initialized. [0000.136] W> DEVICE_PROD: device prod is not initialized. [0000.153] I> Sdmmc: DDR50 mode [0000.157] W> DEVICE_PROD: device prod is not initialized. [0000.163] I> Active boot chain: 0 [0000.166] I> Active boot chain: 0 [0000.169] I> magic:0x43424e00, version: 3, num_slots: 1 [0000.174] W> No valid slot number is found in scratch register [0000.179] W> Return default slot: _a [0000.183] I> Boot chain slot 0 [0000.185] I> Boot-device: eMMC [0000.190] E> No fuse-bypass data [0000.193] E> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT. [0000.199] E> MB1_PLATFORM_CONFIG: Failed to initialize device prod. [0000.206] I> temperature = 33000 [0000.209] W> Skipping boost for clk:bpmp_cpu_nic [0000.214] W> Skipping boost for clk:bpmp_apb [0000.217] W> Skipping boost for clk:axi_cbb [0000.221] W> Skipping boost for clk:aon_cpu_nic [0000.226] W> Skipping boost for clk:aon_can0 [0000.230] W> Skipping boost for clk:aon_can1 [0000.234] I> Boot-device: eMMC [0000.237] I> Boot-device: eMMC [0000.246] I> Sdmmc: HS400 mode enabled [0000.255] I> ECC region[0]: Start:0x0, End:0x0 [0000.259] I> ECC region[1]: Start:0x0, End:0x0 [0000.263] I> ECC region[2]: Start:0x0, End:0x0 [0000.267] I> ECC region[3]: Start:0x0, End:0x0 [0000.271] I> ECC region[4]: Start:0x0, End:0x0 [0000.275] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000 [0000.281] I> Non-ECC region[1]: Start:0x0, End:0x0 [0000.285] I> Non-ECC region[2]: Start:0x0, End:0x0 [0000.290] I> Non-ECC region[3]: Start:0x0, End:0x0 [0000.294] I> Non-ECC region[4]: Start:0x0, End:0x0 [0000.300] W> MB1_PLATFORM_CONFIG: Rail ID 9 not found in pmic rail config table. [0000.307] E> FAILED: Thermal config [0000.311] W> DEVICE_PROD: device prod is not initialized. [0000.316] W> DEVICE_PROD: device prod is not initialized. [0000.325] W> MB1_PLATFORM_CONFIG: Rail ID 7 not found in pmic rail config table. [0000.332] E> FAILED: MEMIO rail config [0000.353] I> scrub mode: full dram [0000.356] E> FUSE: Failed to verify ECID. [0000.369] I> WP-0 triggered [0000.372] I> WP-0 ACK received :) [0000.375] I> sdmmc bdev is already initialized [0000.408] I> WP-1 triggered [0000.414] W> No fuse-bypass data [0000.417] I> SC7 context save done [0000.424] I> WP-1 ACK received :) [0000.427] W> MB1_PLATFORM_CONFIG: Rail ID 8 not found in pmic rail config table. [0000.434] I> MTS carveout BOM: 0xf8000000 [0000.438] I> WP1.5 triggered [0000.490] I> WP1.5 ACK received :) [0000.494] I> MB1 done ÿýÿàmain enter SPE VERSION #: R01.00.10 Created: May 31 2018 @ 13:05:12 HW Function test Start Scheduler. in late init ÿâ [0000.502] I> Welcome to MB2(TBoot-BPMP) [0000.502] E> DEVICE_PROD: Invalid value data = 70020000, size = 0. [0000.503] W> Device prod registration failed [0000.503] I> Boot-device: eMMC [0000.504] I> Boot_device: SDMMC_BOOT instance: 3 [0000.511] I> sdmmc-3 params source = boot args [0000.512] I> sdmmc bdev is already initialized [0000.517] I> sdmmc-3 params source = boot args [0000.523] I> Found 15 partitions in SDMMC_BOOT (instance 3) [0000.530] I> Found 36 partitions in SDMMC_BOOT (instance 3) [0000.532] W> No valid slot number is found in scratch register [0000.537] W> Return default slot: _a [0000.541] I> Active Boot chain : 0 [0000.544] I> Binary@ device:1/3 block-58750712 (partition size: 0x100000) [0000.560] I> Binary@ device:1/3 block-58754808 (partition size: 0x100000) [0000.599] I> Binary@ device:1/3 block-58759928 (partition size: 0x80000) [0000.604] I> Binary@ device:1/3 block-58738680 (partition size: 0x80000) [0000.609] I> Binary@ device:1/3 block-58740728 (partition size: 0x60000) [0000.613] I> BL-DTB loaded successfully [0000.614] I> Relocating BR-BCT [0000.614] I> Binary@ device:1/3 block-58742264 (partition size: 0x200000) [0000.623] I> Unhalting RCE ÿäNOTICE: BL31: v1.3(release):9fc2cdf NOTICE: BL31: Built : 15:08:58, Oct 31 2018 ERROR: Error initializing runtime service trusty_fast ÿâ welcome to lk calling constructors initializing heap creating bootstrap completion thread top of bootstrap2() initializing platform bpmp: platform_init tag is 588c62054ecdba8a44cb9d6ff5d04cb0 tag_show initialized dt initialized mail initialized chipid initialized fuse initialized sku initialized speedo initialized ec_get_ec_list: found 45 ecs ec initialized ec_mrq initialized vmon_populate_monitors: found 3 monitors vmon initialized vmon_soc_self_check: vmon_vsoc: self-check passed adc initialized fmon_populate_monitors: found 73 monitors fmon initialized fmon_mrq initialized reset initialized nvhs initialized warning: aon_cpu_nic do not permit 'allowed-parents' property 387 clocks registered WARNING: pll_c4 has no dyn ramp clk_mrq_init: mrq handler registered clk initialized io_dpd initialized io_dpd initialized thermal initialized i2c5 controller initialized initialized i2c mrq handling i2c initialized regulator initialized avfs_clk_platform initialized soctherm initialized aotag initialized powergate initialized dvs initialized pm initialized pg_late initialized strap initialized tag initialized emc initialized clk_dt initialized avfs_ccplex_platform initialized tj_max: dt node not found tj_init initialized uphy_mrq_init: mrq handler registered uphy_dt initialized uphy initialized mrq initialized ÿá [0001.171] I> Welcome to Cbootÿâfmon_post initialized ÿá [0001.172] I> Cboot Version: 4e3f0bea4cf94837f65ddb512d987e4e8589e811.10.31.2018.43-t194-3d46 [0001.173] I> CPU-BL Params @ 0xf2820000 [0001.173] I> 0) Base:0x00000000 Size:0x00000000 [0001.175] I> 1) Base:0xf2100000 Size:0x00100000 [0001.180] I> 2) Base:0xf2000000 Size:0x00100000 [0001.184] I> 3) Base:0xf1300000 Size:0x00100000 [0001.189] I> 4) Base:0xf1200000 Size:0x00100000 [0001.193] I> 5) Base:0xf1100000 Size:0x00100000 [0001.197] I> 6) Base:0xf3800000 Size:0x00400000 [0001.202] I> 7) Base:0xf1c00000 Size:0x00400000 [0001.206] I> 8) Base:0xf1000000 Size:0x00100000ÿâclk_dt_late initialized ÿá ÿâmachine_check initialized ÿá[0001.213] I> 9) Base:0xf0f00000 Size:0x00100000 ÿâpm_post initialized ÿá[0001.221] I> 10) Base:0xf3000000 Size:0x00800000ÿâdbells initialized ÿá [0001.229] I> 11) Base:0x40000000 Size:0x00040000ÿâavfs_clk_platform_post initialized ÿá [0001.237] I> 12) Base:0xf0e00000 Size:0x00100000 ÿâdmce initialized ÿá[0001.242] I> 13) Base:0x40046000 Size:0x00002000ÿâcvc initialized ÿá [0001.250] I> 14) Base:0x40048000 Size:0x00002000 ÿâccplex_avfs_hw_init: nafll_cluster0: not monitored ÿá[0001.254] I> 15) Base:0xaa000000 Size:0x00004000 ÿâccplex_avfs_hw_init: nafll_cluster1: not monitored ÿá[0001.264] I> 16) Base:0x4004a000 Size:0x00002000 ÿâccplex_avfs_hw_init: nafll_cluster2: not monitored ÿá[0001.273] I> 17) Base:0xf0d00000 Size:0x00100000 ÿâccplex_avfs_hw_init: nafll_cluster3: not monitored ÿá[0001.282] I> 18) Base:0x4004c000 Size:0x00002000 ÿâavfs_clk_mach_post initialized ÿá[0001.292] I> 19) Base:0xf2200000 Size:0x00600000 ÿâregulator_post initialized ÿá[0001.299] I> 20) Base:0x4004e000 Size:0x00002000 ÿârm initialized ÿá[0001.307] I> 21) Base:0xf0cd0000 Size:0x0000c000 ÿâsc7_diag initialized ÿá[0001.313] I> 22) Base:0x00000000 Size:0x00000000 ÿâthermal_test initialized ÿá[0001.320] I> 23) Base:0xf0ce0000 Size:0x00020000 ÿâserial_late initialized ÿá[0001.327] I> 24) Base:0xf6000000 Size:0x02000000 ÿâclk_post initialized ÿá[0001.334] I> 25) Base:0x40050000 Size:0x00002000 ÿâclk_dt_post initialized ÿá[0001.341] I> 26) Base:0x40040000 Size:0x00006000 ÿâmc_pcie initialized ÿá[0001.348] I> 27) Base:0xf1800000 Size:0x00400000 [0001.354] I> 28) Base:0xf4c00000 Size:0x01400000 [0001.359] I> 29) Base:0xf1400000 Size:0x00400000 ÿâpg_post initialized ÿá[0001.363] I> 30) Base:0x00000000 Size:0x00000000 ÿâsku_debugfs initialized ÿá[0001.370] I> 31) Base:0x00000000 Size:0x00000000 ÿâspeedo_debugfs initialized ÿá[0001.377] I> 32) Base:0xf8000000 Size:0x08000000 ÿâadc_debugfs initialized ÿá[0001.384] I> 33) Base:0x00000000 Size:0x00000000 [0001.391] I> 34) Base:0xf3c00000 Size:0x01000000 [0001.395] I> 35) Base:0x00000000 Size:0x00000000 [0001.400] I> 36) Base:0xa0000000 Size:0x09000000 [0001.404] I> 37) Base:0xf2800000 Size:0x00800000 [0001.409] I> 38) Base:0x80000000 Size:0x20000000 ÿâclk_debugfs initialized ÿá[0001.413] I> 39) Base:0xb0000000 Size:0x08000000 [0001.420] I> 40) Base:0x00000000 Size:0x00000000 [0001.425] I> 41) Base:0x00000000 Size:0x00000000 [0001.429] I> 42) Base:0x00000000 Size:0x00000000 [0001.434] I> 43) Base:0x00000000 Size:0x00000000 [0001.438] I> 44) Base:0x00000000 Size:0x00000000 [0001.443] I> 45) Base:0x00000000 Size:0x00000000 [0001.447] GIC-SPI Target CPU: 0 [0001.450] Interrupts Init done [0001.453] calling constructors [0001.456] initializing heap [0001.458] I> Heap: [0xa06872c8 ... 0xa8f00000] [0001.463] initializing threads [0001.466] initializing timers [0001.468] creating bootstrap completion thread [0001.473] top of bootstrap2() [0001.476] CPU: MIDR: 0x4E0F0040, MPIDR: 0x80000000 [0001.480] initializing platform [0001.483] E> DEVICE_PROD: Invalid value data = 0, size = 0. [0001.489] W> device prod register failed ÿâemc_debugfs initialized ÿá[0001.492] I> Bl_dtb @0xa8f00000 ÿâdvs_debugfs initialized ÿá[0001.498] I> gpio framework initialized ÿâfmon_debugfs initialized vmon_debugfs initialized pg_debugfs initialized profile_fs initialized ÿá[0001.511] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio' driver ÿâdebugfs_cons initialized l_fs initialized ÿá[0001.525] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio-aon' driver ÿâprofile initialized _debugfs initialized ÿá[0001.532] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x46 ÿâdmce_debugfs initialized ec_debugfs initialized ÿá[0001.547] E> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539 ÿâsoctherm_debug initialized reader initialized ÿá[0001.559] E> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539ÿâmods initialized fs initialized ÿá ÿâdebugfs_mrq initialized ÿá[0001.571] W> tegrabl_tca9539_init: failed to fetch phandle from dt ÿâinitializing target ÿá[0001.579] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x44 ÿâcalling apps_init() ÿá[0001.589] E> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539 ÿâstarting app shell ering main console loop ÿá[0001.599] E> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539ÿâ] ÿá [0001.610] W> tegrabl_tca9539_init: failed to fetch phandle from dt [0001.618] I> fixed regulator driver initialized [0001.631] I> register 'maxim' power off handle [0001.632] I> virtual i2c enabled [0001.632] I> registered 'maxim,max20024' pmic [0001.633] I> tegrabl_gpio_driver_register: register 'max20024-gpio' driver [0001.639] I> Boot-device: eMMC [0001.642] I> Boot_device: SDMMC_BOOT instance: 3 [0001.648] I> sdmmc-3 params source = boot args [0001.651] I> sdmmc bdev is already initialized [0001.655] I> sdmmc-3 params source = boot args [0001.661] I> Found 15 partitions in SDMMC_BOOT (instance 3) [0001.667] I> Found 36 partitions in SDMMC_BOOT (instance 3) [0001.670] I> Load in CBoot Boot Options partition and parse it [0001.683] E> Error -9 when finding node with path /boot-configuration [0001.684] E> tegrabl_cbo_parse_info: "boot-configuration" not found in CBO file. [0001.690] E> "plugin-manager" doesn't exist, creating [0001.694] E> "ids" doesn't exist, creating [0001.699] E> "connection" doesn't exist, creating [0001.703] E> "configs" doesn't exist, creating [0001.709] I> Find /i2c@3160000's alias i2c0 [0001.711] I> Reading eeprom i2c=0 address=0x50 [0001.742] I> Device at /i2c@3160000:0x50 [0001.742] I> Reading eeprom i2c=0 address=0x56 [0001.767] I> Device at /i2c@3160000:0x56 [0001.769] I> Find /i2c@3180000's alias i2c2 [0001.769] I> Reading eeprom i2c=2 address=0x54 [0001.771] E> I2C: slave not found in slaves. [0001.771] E> I2C: Could not write 0 bytes to slave: 0x00a8 with repeat start true. [0001.772] E> I2C_DEV: Failed to send register address 0x00000000. [0001.773] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa8 at 0x00000000 via instance 2. [0001.782] E> eeprom: Failed to read I2C slave device [0001.786] I> Eeprom read failed 0x3526070d [0001.790] I> Reading eeprom i2c=2 address=0x57 [0001.795] E> I2C: slave not found in slaves. [0001.799] E> I2C: Could not write 0 bytes to slave: 0x00ae with repeat start true. [0001.807] E> I2C_DEV: Failed to send register address 0x00000000. [0001.812] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xae at 0x00000000 via instance 2. [0001.822] E> eeprom: Failed to read I2C slave device [0001.826] I> Eeprom read failed 0x3526070d [0001.830] I> Reading eeprom i2c=2 address=0x52 [0001.835] E> I2C: slave not found in slaves. [0001.839] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.847] E> I2C_DEV: Failed to send register address 0x00000000. [0001.852] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 2. [0001.862] E> eeprom: Failed to read I2C slave device [0001.867] I> Eeprom read failed 0x3526070d [0001.871] I> Find /i2c@c240000's alias i2c1 [0001.875] I> Reading eeprom i2c=1 address=0x52 [0001.880] E> I2C: slave not found in slaves. [0001.883] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.891] E> I2C_DEV: Failed to send register address 0x00000000. [0001.896] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 1. [0001.906] E> eeprom: Retry to read I2C slave device. [0001.911] E> I2C: slave not found in slaves. [0001.915] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true. [0001.923] E> I2C_DEV: Failed to send register address 0x00000000. [0001.928] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 1. [0001.938] E> eeprom: Failed to read I2C slave device [0001.943] I> Eeprom read failed 0x3526070d [0001.946] I> Reading eeprom i2c=1 address=0x50 [0001.951] E> I2C: slave not found in slaves. [0001.955] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true. [0001.963] E> I2C_DEV: Failed to send register address 0x00000000. [0001.968] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0x00000000 via instance 1. [0001.978] E> eeprom: Retry to read I2C slave device. [0001.983] E> I2C: slave not found in slaves. [0001.987] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true. [0001.995] E> I2C_DEV: Failed to send register address 0x00000000. [0002.000] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0x00000000 via instance 1. [0002.010] E> eeprom: Failed to read I2C slave device [0002.014] I> Eeprom read failed 0x3526070d [0002.018] I> create_pm_ids: id: 2888-0004-400-M, len: 15 [0002.024] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0002.035] I> create_pm_ids: id: 2822-0000-700-L, len: 15 [0002.040] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93 [0002.051] I> Adding plugin-manager/ids/2888-0004-400=/i2c@3160000:module@0x50 [0002.058] E> "i2c@3160000" doesn't exist, creating [0002.062] E> "module@0x50" doesn't exist, creating [0002.067] I> Adding plugin-manager/ids/2822-0000-700=/i2c@3160000:module@0x56 [0002.074] E> "module@0x56" doesn't exist, creating [0002.080] I> Adding plugin-manager/cvm [0002.083] E> "chip-id" doesn't exist, creating [0002.087] I> Adding plugin-manager/chip-id/A02P [0002.091] I> Plugin-manager override starting [0002.097] I> node /plugin-manager/fragment-p2888@0 matches [0002.114] I> node /plugin-manager/fragement-tegra-wdt-en matches [0002.118] I> node /plugin-manager/fragement-soft-wdt matches [0002.122] I> node /plugin-manager/fragment-pcie-c1-rp matches [0002.124] I> node /plugin-manager/fragment-pcie-p2822-B00 matches [0002.128] I> node /plugin-manager/fragment-pcie-c5-rp matches [0002.133] I> node /plugin-manager/fragment-tegra-ufs-lane10 matches [0002.136] I> node /plugin-manager/pwm-fan-polarity matches [0002.150] I> node /plugin-manager/ufs-cd matches [0002.156] I> Disable plugin-manager status in FDT [0002.156] I> Plugin-manager override finished successfully [0002.167] I> enabling 'vdd-hdmi-5v0' regulator [0002.172] I> regulator 'vdd-hdmi-5v0' already enabled [0002.173] I> hdmi cable connected [0002.175] E> set volts not configured for 'vdd-1v0' [0002.177] E> set volts not configured for 'vdd-1v8-hs' [0002.182] E> invalid display type [0002.186] E> invalid display type [0002.187] E> cannot find any other nvdisp nodes [0002.204] I> edid read success [0002.216] I> edid read success [0002.217] I> width = 640, height = 480, frequency = 25174825 [0002.217] I> width = 640, height = 480, frequency = 25174825 [0002.218] I> width = 1920, height = 1080, frequency = 148500000 [0002.218] I> width = 1920, height = 1080, frequency = 148500000 [0002.218] I> width = 1920, height = 1080, frequency = 148351648 [0002.223] I> width = 1280, height = 720, frequency = 74175824 [0002.228] I> width = 720, height = 480, frequency = 26973026 [0002.234] I> width = 720, height = 480, frequency = 26973026 [0002.239] I> width = 640, height = 480, frequency = 25174825 [0002.245] I> width = 1920, height = 1080, frequency = 148351648 [0002.251] I> width = 720, height = 576, frequency = 26973026 [0002.256] I> width = 1280, height = 720, frequency = 74175824 [0002.262] I> Best mode Width = 1920, Height = 1080, freq = 148351648 [0002.272] I> hdmi_enable, starting HDMI initialisation [0002.277] I> hdmi_enable, HDMI initialisation complete [0002.285] initializing target [0002.286] calling apps_init() [0002.286] starting app kernel_boot_app [0002.345] I> decompressor handler not found [0002.345] I> Kernel type = Normal [0002.345] I> Loading kernel & kernel-dtb from removable storage (5) [0002.346] I> No sdcard [0002.346] I> -0 params source = [0002.347] E> Blockdev open: exit error [0002.347] I> Loading kernel & kernel-dtb from removable storage (6) [0002.353] W> No valid slot number is found in scratch register [0002.354] W> Return default slot: _a [0002.358] I> USB Firmware Version: 60.05 release [0002.813] E> failed to initialize xhci controller [0002.814] E> Error in init of XUSB host driver, err: 79790026 [0002.814] W> Failed to initialize device 6-0 [0002.815] I> Loading kernel/boot.img from built-in storage ... [0002.815] W> No valid slot number is found in scratch register [0002.815] W> Return default slot: _a [0002.818] I> A/B: bin_type (37) slot 0 [0002.821] I> Loading partition kernel at 0xa1930000 from device(0x1) [0003.203] I> T19x: Authenticate kernel (bin_type: 37), max size 0x4000000 [0003.548] W> No valid slot number is found in scratch register [0003.548] W> Return default slot: _a [0003.549] I> A/B: bin_type (38) slot 0 [0003.549] I> Loading partition kernel-dtb at 0x91000000 from device(0x1) [0003.554] I> T19x: Authenticate kernel-dtb (bin_type: 38), max size 0x80000 [0003.557] I> Kernel hdr @0xa1930000 [0003.557] I> Kernel dtb @0x91000000 [0003.558] I> Checking boot.img header magic ... [0003.560] I> [OK] [0003.562] I> Valid boot.img @ 0xa1930000 [0003.565] I> decompressor handler not found [0003.569] I> Copying kernel image (34404360 bytes) from 0xa1930800 to 0x80080000 ... [0003.594] I> Done [0003.595] I> Move ramdisk (len: 0) from 0xa3a00800 to 0x92000000 [0003.596] I> Updated bpmp info to DTB [0003.597] I> Ramdisk: Base: 0x92000000; Size: 0x0 [0003.598] I> Updated initrd info to DTB [0003.598] W> WARN: Fail to override "console=none" in commandline [0003.602] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0003.609] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params [0003.617] W> No valid slot number is found in scratch register [0003.622] W> Return default slot: _a [0003.626] I> Active slot suffix: [0003.629] I> add_boot_slot_suffix: slot_suffix = [0003.634] I> Linux Cmdline: root=/dev/mmcblk0p1 rw rootwait console=ttyTCU0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 rootfstype=ext4 OS=l4t video=tegrafb no_console_suspend=1 earlycon=tegra_comb_uart,mmio32,0x0c168000 gpt tegra_fbmem=0x800000@0xa0791000 lut_mem=0x2008@0xa078e000 usbcore.old_scheme_first=1 tegraid=19.1.2.0.0 maxcpus=8 boot.slot_suffix= boot.ratchetvalues=0.2.2 sdhci_tegra.en_boot_part_access=1 [0003.671] I> Updated bootarg info to DTB [0003.674] W> MAC addr invalid! [0003.677] E> Failed to get WIFI MAC address [0003.681] W> MAC addr invalid! [0003.684] E> Failed to get Bluetooth MAC address [0003.689] I> eeprom_get_mac_addr: MAC (type: 2): 48:b0:2d:3c:7e:da [0003.695] E> "plugin-manager" doesn't exist, creating [0003.700] I> Adding /chosen/plugin-manager/cvm [0003.704] E> "chip-id" doesn't exist, creating [0003.708] I> Adding /chosen/plugin-manager/chip-id [0003.713] E> "configs" doesn't exist, creating [0003.717] I> Adding /chosen/plugin-manager/configs [0003.722] E> "ids" doesn't exist, creating [0003.726] I> Adding /chosen/plugin-manager/ids [0003.730] E> "odm-data" doesn't exist, creating [0003.734] I> Adding /chosen/plugin-manager/odm-data [0003.743] E> "memory" doesn't exist, creating [0003.744] I> [0] START: 0x80000000, END: 0xaa000000 [0003.748] I> [1] START: 0xaa004000, END: 0xf0cd0000 [0003.753] I> [2] START: 0xf0cdc000, END: 0xf0ce0000 [0003.757] I> dram_block larger than 80000000 [0003.761] I> [3] START: 0x100000000, END: 0x880000000 [0003.766] I> added [base:0x80000000, size:0x2a000000] to /memory [0003.772] I> added [base:0xaa200000, size:0x46a00000] to /memory [0003.778] I> added [base:0x100000000, size:0x780000000] to /memory [0003.785] I> Updated memory info to DTB [0003.788] E> "reset" doesn't exist, creating [0003.793] I> NVG: Logical CPU: 0; MPIDR: 0x80000000 [0003.797] I> Enabled cpu-0 (mpidr: 0x0) node in FDT [0003.801] I> NVG: Logical CPU: 1; MPIDR: 0x80000001 [0003.806] I> Enabled cpu-1 (mpidr: 0x1) node in FDT [0003.811] I> NVG: Logical CPU: 2; MPIDR: 0x80000100 [0003.815] I> Enabled cpu-2 (mpidr: 0x100) node in FDT [0003.820] I> NVG: Logical CPU: 3; MPIDR: 0x80000101 [0003.825] I> Enabled cpu-3 (mpidr: 0x101) node in FDT [0003.830] I> NVG: Logical CPU: 4; MPIDR: 0x80000200 [0003.835] I> Enabled cpu-4 (mpidr: 0x200) node in FDT [0003.840] I> NVG: Logical CPU: 5; MPIDR: 0x80000201 [0003.844] I> Enabled cpu-5 (mpidr: 0x201) node in FDT [0003.849] I> NVG: Logical CPU: 6; MPIDR: 0x80000300 [0003.854] I> Enabled cpu-6 (mpidr: 0x300) node in FDT [0003.859] I> NVG: Logical CPU: 7; MPIDR: 0x80000301 [0003.864] I> Enabled cpu-7 (mpidr: 0x301) node in FDT [0003.870] E> "misc-data" doesn't exist, creating [0003.873] I> Boot-device: eMMC [0003.876] I> Add boot-sdmmc to plugin-manager/misc-data [0003.881] I> Add storage-sdmmc to plugin-manager/misc-data [0003.886] W> Unknown storage device [0003.890] I> Add serial number as DT property [0003.895] I> Plugin-manager override starting [0003.899] I> node /plugin-manager/fragment-p2888@0 matches [0003.915] I> node /plugin-manager/fragement-tegra-wdt-en matches [0003.918] I> node /plugin-manager/fragement-soft-wdt matches [0003.922] I> node /plugin-manager/fragment-pcie-c1-rp matches [0003.924] I> node /plugin-manager/fragment-pcie-p2822-B00 matches [0003.930] I> node /plugin-manager/fragment-pcie-c5-rp matches [0003.938] I> node /plugin-manager/fragment-tegra-ufs-lane10 matches [0003.940] I> node /plugin-manager/pwm-fan-polarity matches [0003.950] I> node /plugin-manager/ufs-cd matches [0003.954] I> Disable plugin-manager status in FDT [0003.954] I> Plugin-manager override finished successfully [0003.982] I> Filling next stage params: ep: 0x80080000, dtb: 0x91000000 [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.108-tegra (buildbrain@mobile-u64-2565) (gcc version 6.4.1 20170707 (Linaro GCC 6.4-2017.08) ) #1 SMP PREEMPT Wed Oct 31 15:17:21 PDT 2018 [ 0.000000] Boot CPU: AArch64 Processor [4e0f0040] [ 0.000000] OF: fdt:memory scan node memory, reg size 48, [ 0.000000] OF: fdt: - 80000000 , 2a000000 [ 0.000000] OF: fdt: - aa200000 , 46a00000 [ 0.000000] OF: fdt: - 100000000 , 780000000 [ 0.000000] earlycon: tegra_comb_uart0 at MMIO32 0x000000000c168000 (options '') [ 0.000000] bootconsole [tegra_comb_uart0] enabled [ 0.000000] Found tegra_fbmem: 00800000@a0791000 [ 0.000000] Found lut_mem: 00002008@a078e000 [ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] OF: reserved mem: initialized node grid-of-semaphores, compatible id nvidia,gosmem [ 0.000000] cma: Reserved 64 MiB at 0x00000000ec800000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 23 pages/cpu @ffffffc7ffdb5000 s54424 r8192 d31592 u94208 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8195040 [ 0.000000] Kernel command line: root=/dev/mmcblk0p1 rw rootwait console=ttyTCU0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 rootfstype=ext4 OS=l4t video=tegrafb no_console_suspend=1 earlycon=tegra_comb_uart,mmio32,0x0c168000 gpt tegra_fbmem=0x800000@0xa0791000 lut_mem=0x2008@0xa078e000 usbcore.old_scheme_first=1 tegraid=19.1.2.0.0 maxcpus=8 boot.slot_suffix= boot.ratchetvalues=0.2.2 sdhci_tegra.en_boot_part_access=1 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 4194304 (order: 13, 33554432 bytes) [ 0.000000] Inode-cache hash table entries: 2097152 (order: 12, 16777216 bytes) [ 0.000000] Memory: 32615328K/33300480K available (15358K kernel code, 2942K rwdata, 6724K rodata, 8512K init, 1623K bss, 619616K reserved, 65536K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f80000 ( 15360 KB) [ 0.000000] .rodata : 0xffffff8008f80000 - 0xffffff8009620000 ( 6784 KB) [ 0.000000] .init : 0xffffff8009620000 - 0xffffff8009e70000 ( 8512 KB) [ 0.000000] .data : 0xffffff8009e70000 - 0xffffff800a14f808 ( 2943 KB) [ 0.000000] .bss : 0xffffff800a14f808 - 0xffffff800a2e5584 ( 1624 KB) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf20000000 ( 512 MB actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc800000000 ( 32768 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=8. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=8 [ 0.000000] ********************************************************** [ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.000000] ** ** [ 0.000000] ** trace_printk() being used. Allocating extra memory. ** [ 0.000000] ** ** [ 0.000000] ** This means that this is a DEBUG kernel and it is ** [ 0.000000] ** unsafe for production use. ** [ 0.000000] ** ** [ 0.000000] ** If you see this message and you are not debugging ** [ 0.000000] ** the kernel, report this immediately to your vendor! ** [ 0.000000] ** ** [ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.000000] ********************************************************** [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 31.25MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xe6a171046, max_idle_ns: 881590405314 ns [ 0.000034] sched_clock: 56 bits at 31MHz, resolution 32ns, wraps every 4398046511088ns [ 0.009147] Console: colour dummy device 80x25 [ 0.012601] console [tty0] enabled [ 0.015796] bootconsole [tegra_comb_uart0] disabled