Enter choice: $"@  [0000.126] [TegraBoot] (version 00.00.2018.01-l4t-89b97a)
[0000.131] Processing in cold boot mode Bootloader 2
[0000.136] A02 Bootrom Patch rev = 1023
[0000.140] Power-up reason: pmc por
[0000.143] No Battery Present
[0000.145] pmic max77620 reset reason
[0000.149] pmic max77620 NVERC : 0x40
[0000.152] RamCode = 0
[0000.154] Platform has DDR4 type RAM
[0000.158] max77620 disabling SD1 Remote Sense
[0000.162] Setting DDR voltage to 1125mv
[0000.166] Serial Number of Pmic Max77663: 0x2421e8
[0000.174] Entering ramdump check
[0000.177] Get RamDumpCarveOut = 0x0
[0000.180] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0000.185] Last reboot was clean, booting normally!
[0000.190] Sdram initialization is successful 
[0000.194] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.200] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.206] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.212] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.217] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.223] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.229] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.235] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.251] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.257] Platform-DebugCarveout: 0
[0000.260] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.266] Non secure mode, and RB not enabled.
[0000.393] Csd NumOfBlocks=124735488
[0000.398] Set High speed to 1
[0000.402] Error mask set in wait for cmd complete with error 0x3 in HwSdmmcWai 
[0000.412] Command complete wait failed with error 0x3 Interrupt 0x18001
[0000.418] Number of retries left 4
[0000.430] Using GPT Primary to query partitions
[0000.435] Loading Tboot-CPU binary
[0000.448] Verifying TBC in OdmNonSecureSBK mode
[0000.458] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.465] Bootloader downloaded successfully.
[0000.469] Downloaded Tboot-CPU binary to 0xa0000258
[0000.474] MAX77620_GPIO5 configured
[0000.477] CPU power rail is up
[0000.480] CPU clock enabled
[0000.484] Performing RAM repair
[0000.487] Updating A64 Warmreset Address to 0xa00002e9
[0000.492] Loading NvTbootBootloaderDTB
[0000.529] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0000.590] Bootloader DTB Load Address: 0x83000000
[0000.595] Loading NvTbootKernelDTB
[0000.632] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0000.693] Kernel DTB Load Address: 0x83100000
[0000.700] Loading cboot binary
[0000.744] Verifying EBT in OdmNonSecureSBK mode
[0000.786] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0000.793] Bootloader downloaded successfully.
[0000.798] Next binary entry address: 0x92c00258 
[0000.802] BoardId: 3448
[0000.807] Overriding pmu board id with proc board id
[0000.812] Display board id is not available 
[0000.854] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0000.908] /bpmp deleted
[0000.910] SC7EntryFw header found loaded at 0xff700000
[0001.101] OVR2 PMIC
[0001.103] Bpmp FW successfully loaded
[0001.109] WB0 init successfully at 0xff780000
[0001.113] Set NvDecSticky Bits
[0001.117] GSC2 address ff53fffc value c0edbbcc
[0001.123] GSC MC Settings done
[0001.128] TOS Image length 53680
[0001.131]  Monitor size 53680
[0001.134]  OS size 0
[0001.144] Secure Os AES-CMAC Verification Success!
[0001.149] TOS image cipher info: plaintext
[0001.153] Loading and Validation of Secure OS Successful
[0001.169] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.173] NvTbootPackSdramParams: start. 
[0001.179] NvTbootPackSdramParams: done. 
[0001.182] Tegraboot started after 53764 us
[0001.186] Basic modules init took 782297 us
[0001.190] NvTbootQspiFlashIoctl: Opcode = 1 not supported
[0001.195] Sec Bootdevice Read Time = 622327755 ms, Read Size = 622327755 KB
[0001.202] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0001.208] Storage Device Read Time = 179 ms, Read Size = 2241 KB
[0001.214] Storage Device Write Time = 0 ms, Write Size = 0 KB
[0001.219] Next stage binary read took 39424 us
[0001.223] Carveout took -51089 us
[0001.226] CPU initialization took 386695 us
[0001.230] Total time taken by TegraBoot 1157327 us

[0001.235] Starting CPU & Halting co-processor 

64NOTICE:  BL31: v1.3(release):eca0c5e
NOTICE:  BL31: Built : 00:21:27, Mar 13 2019
ERROR:   Error initializing runtime service trusty_fast
[0001.357] RamCode = 0
[0001.362] LPDDR4 Training: Read DT: Number of tables = 2
[0001.367] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0001.380] EMC Training Successful
[0001.383] 408000 not found in DVFS table
[0001.389] RamCode = 0
[0001.393] DT Write: emc-table@204000 succeeded
[0001.398] DT Write: emc-table@1600000 succeeded
[0001.402] LPDDR4 Training: Write DT: Number of tables = 2
[0001.445] 
[0001.446] Debug Init done
[0001.449] Marked DTB cacheable
[0001.452] Bootloader DTB loaded at 0x83000000
[0001.456] Marked DTB cacheable
[0001.459] Kernel DTB loaded at 0x83100000
[0001.463] DeviceTree Init done
[0001.475] Pinmux applied successfully
[0001.480] gicd_base: 0x50041000
[0001.483] gicc_base: 0x50042000
[0001.486] Interrupts Init done
[0001.490] Using base:0x60005090 & irq:208 for tick-timer
[0001.496] Using base:0x60005098 for delay-timer
[0001.500] platform_init_timer: DONE
[0001.504] Timer(tick) Init done
[0001.507] osc freq = 38400 khz
[0001.511] 
[0001.512] welcome to cboot
[0001.515] 
[0001.516] Cboot Version: 00.00.2018.01-t210-f76b856b
[0001.521] calling constructors
[0001.524] initializing heap