[0009.945] Enabled early print [0009.948] [TegraBoot] (version 00.00.2014.50-mobile-12e1c662) [0009.953] Processing in recovery mode [0009.957] A02 Bootrom Patch rev = 63 [0009.960] Power-up reason: pmc por [0009.963] Established communication link with host [0010.949] Odmdata from BCT: 0x00084000 [0010.952] DebugPort= 0x3 [0010.955] BoardId read from EEPROM/NCT: 2180 [0010.983] Turned on fan for loki board [0010.986] Key release before reqd. time for fastboot [0010.991] No Battery Present [0010.994] RamCode = 0 [0010.996] Platform has Ddr4 type ram [0010.999] max77620 disabling SD1 Remote Sense [0011.004] Setting Ddr voltage to 1125mv [0011.008] Serial Number of Pmic Max77663: 0x60ead [0011.015] Entering ramdump check [0011.018] Get RamDumpCarveOut = 0x0 [0011.022] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0011.027] Last reboot was clean, booting normally! [0011.031] Sdram initialization is successful [0011.035] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0011.041] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0011.046] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0011.051] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0011.056] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0011.062] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0011.067] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0011.072] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0011.087] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0011.093] Platform-DebugCarveout: 0 [0011.096] Downloaded Bct successfully [0011.213] Downloaded bootloader successfully at 0x92c00000 [0011.317] Downloaded rp1 successfully at 0x83000000 [0011.396] MAX77620_GPIO1 Configured. [0011.400] MAX77620_GPIO5 Configured. [0011.403] CPU power rail is up [0011.406] CPU clock enabled [0011.410] Performing RAM repair [0011.413] Updating A64 Warmreset Address to 0x92c002e9 [0011.419] Enable APE clock/reset [0011.422] Error in NvTbootGetTOSBinaryLength: 0x11 ! [0011.427] Loading Secure OS image failed. [0011.431] Set NvDecSticky Bits [0011.434] GSC1 address : ff700000 [0011.438] GSC2 address ff63fffc value c0edbbcc [0011.442] GSC2 address : ff600000 [0011.446] GSC3 address : ff500000 [0011.450] GSC4 address : ff400000 [0011.453] GSC5 address : ff300000 [0011.457] GSC MC Settings done [0011.460] NvTbootPackSdramParams: start. [0011.465] NvTbootPackSdramParams: done. [0011.468] Next binary entry address: 0x92c00258 [0011.473] BoardId: 2180 [0011.476] dram memory type is 3 [0011.479] Tegraboot started after 10183950 us [0011.483] Basic modules init took -10183950 us [0011.487] USB data transfer took 0 us [0011.491] Carveout took 11751010 us [0011.494] CPU initialization took 3646 us [0011.498] Total time taken by TegraBoot 1570706 us [0011.503] Starting CPU & Halting co-processor [0011.789] [0011.790] Debug Init done [0011.794] Marked DTB cacheable [0011.797] Bootloader DTB loaded at 0x83000400 [0011.801] DeviceTree Init done [0011.823] Pinmux applied successfully [0011.829] gicd_base: 0x50041000 [0011.833] gicc_base: 0x50042000 [0011.836] Interrupts Init done [0011.842] Using base:0x60005008 & irq:33 for tick-timer [0011.847] Using base:0x60005000 for delay-timer [0011.851] platform_init_timer: DONE [0011.855] Timer(tick) Init done [0011.860] osc freq = 38400 khz [0011.865] [0011.866] welcome to cboot [0011.869] [0011.870] Cboot Version: 00.00.2014.50-t210-e831cf53 [0011.875] calling constructors [0011.878] initializing heap [0011.881] initializing threads [0011.884] initializing timers [0011.887] creating bootstrap completion thread [0011.891] top of bootstrap2() [0011.894] CPU: ARM Cortex A57 [0011.897] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0011.901] initializing platform [0011.928] config for ddr50 mode completed [0011.932] sdmmc bdev is already initialized [0011.936] of_register: registering tegra_udc to of_hal [0011.941] of_register: registering inv20628-driver to of_hal [0011.946] of_register: registering ads1015-driver to of_hal [0011.952] of_register: registering lp8557-bl-driver to of_hal [0011.958] of_register: registering bq2419x_charger to of_hal [0011.963] of_register: registering cpc to of_hal [0011.968] of_register: registering bq27441_fuel_gauge to of_hal [0011.988] gpio framework initialized [0011.991] of_register: registering tca9539_gpio to of_hal [0011.997] of_register: registering tca9539_gpio to of_hal [0012.002] of_register: registering i2c_bus_driver to of_hal [0012.008] of_register: registering i2c_bus_driver to of_hal [0012.013] of_register: registering i2c_bus_driver to of_hal [0012.019] pmic framework initialized [0012.022] of_register: registering max77620_pmic to of_hal [0012.028] regulator framework initialized [0012.032] of_register: registering tegra_xhci to of_hal [0012.037] initializing target [0012.046] gpio_driver_register: register 'tegra_gpio_driver' driver [0012.058] fixed regulator driver initialized [0012.137] initializing OF layer [0012.141] of_children_init: Ops found for compatible string nvidia,tegra210-xhci [0012.149] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0012.182] I2C Bus Init done [0012.184] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0012.199] I2C Bus Init done [0012.202] of_children_init: Ops found for compatible string ti,tca9539 [0012.216] tca9539_init: i2c bus: 2, slave addr: 0xe8 [0012.222] gpio_driver_register: register 'tca9539_gpio_driver' driver [0012.228] of_children_init: Ops found for compatible string ti,tca9539 [0012.243] tca9539_init: i2c bus: 2, slave addr: 0xee [0012.248] gpio_driver_register: register 'tca9539_gpio_driver' driver [0012.255] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0012.270] I2C Bus Init done [0012.272] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0012.287] I2C Bus Init done [0012.290] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0012.305] I2C Bus Init done [0012.308] of_children_init: Ops found for compatible string maxim,max77620 [0012.323] max77620_init using irq 118 [0012.328] register 'maxim,max77620' pmic [0012.333] gpio_driver_register: register 'max77620-gpio' driver [0012.339] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0012.354] I2C Bus Init done [0012.359] calling apps_init() [0012.365] Found 19 GPT partitions in "sdmmc3_user" [0012.370] Proceeding to flashing Server [0012.373] usbdcd_reinit Initialize driver to use already enumerated device [0012.380] nv3p_priv_usbf_open USB configuration success [0012.390] Writing GPT partition [0012.395] Erasing Boot device [0012.421] Erasing Storage Device [0013.261] Sanitizing Storage Device [0013.401] Writing protective mbr [0013.405] Writing primary GPT [0013.410] Writing secondary GPT [0013.416] Found 19 GPT partitions in "sdmmc3_user" [0013.423] Writing NVC partition [0013.426] bct_init bctinit [0013.429] bct_init bctinit [0013.438] bct_init bctinit [0013.441] bct_init bctinit [0013.444] bct_init bctinit [0013.468] partition NVC write successful. [0013.474] Writing APP partition [0013.477] bct_init bctinit [0015.985] bct_init bctinit [0015.988] bct_init bctinit [0018.449] bct_init bctinit [0018.452] bct_init bctinit [0020.903] bct_init bctinit [0020.906] bct_init bctinit [0023.367] bct_init bctinit [0023.369] bct_init bctinit [0025.820] bct_init bctinit [0025.823] bct_init bctinit [0028.273] bct_init bctinit [0028.276] bct_init bctinit [0030.728] bct_init bctinit [0030.730] bct_init bctinit [0033.193] bct_init bctinit [0033.196] bct_init bctinit [0035.654] bct_init bctinit [0035.656] bct_init bctinit [0038.115] bct_init bctinit [0038.118] bct_init bctinit [0040.672] bct_init bctinit [0040.675] bct_init bctinit [0042.330] max77620_clear_syswdt clearing watchdog [0043.251] bct_init bctinit [0043.254] bct_init bctinit [0045.980] bct_init bctinit [0045.983] bct_init bctinit [0048.495] bct_init bctinit [0048.498] bct_init bctinit [0051.048] bct_init bctinit [0051.051] bct_init bctinit [0053.529] bct_init bctinit [0053.531] bct_init bctinit [0056.038] bct_init bctinit [0056.041] bct_init bctinit [0058.516] bct_init bctinit [0058.518] bct_init bctinit [0061.096] bct_init bctinit [0061.098] bct_init bctinit [0063.595] bct_init bctinit [0063.597] bct_init bctinit [0066.053] bct_init bctinit [0066.056] bct_init bctinit [0068.509] bct_init bctinit [0068.512] bct_init bctinit [0071.019] bct_init bctinit [0071.022] bct_init bctinit [0072.333] max77620_clear_syswdt clearing watchdog [0073.521] bct_init bctinit [0073.523] bct_init bctinit [0075.977] bct_init bctinit [0075.980] bct_init bctinit [0078.434] bct_init bctinit [0078.437] bct_init bctinit [0080.950] bct_init bctinit [0080.952] bct_init bctinit [0083.579] bct_init bctinit [0083.582] bct_init bctinit [0086.039] bct_init bctinit [0086.041] bct_init bctinit [0088.499] bct_init bctinit [0088.501] bct_init bctinit [0090.963] bct_init bctinit [0090.965] bct_init bctinit [0093.466] bct_init bctinit [0093.469] bct_init bctinit [0096.047] bct_init bctinit [0096.049] bct_init bctinit [0098.576] bct_init bctinit [0098.579] bct_init bctinit [0101.164] bct_init bctinit [0101.167] bct_init bctinit [0102.336] max77620_clear_syswdt clearing watchdog [0103.705] bct_init bctinit [0103.708] bct_init bctinit [0106.160] bct_init bctinit [0106.162] bct_init bctinit [0108.652] bct_init bctinit [0108.654] bct_init bctinit [0111.118] bct_init bctinit [0111.120] bct_init bctinit [0113.577] bct_init bctinit [0113.580] bct_init bctinit [0116.047] bct_init bctinit [0116.049] bct_init bctinit [0118.504] bct_init bctinit [0118.507] bct_init bctinit [0121.060] bct_init bctinit [0121.063] bct_init bctinit [0123.519] bct_init bctinit [0123.521] bct_init bctinit [0125.992] bct_init bctinit [0125.995] bct_init bctinit [0128.464] bct_init bctinit [0128.466] bct_init bctinit [0130.931] bct_init bctinit [0130.934] bct_init bctinit [0132.339] max77620_clear_syswdt clearing watchdog [0133.394] bct_init bctinit [0133.396] bct_init bctinit [0135.864] bct_init bctinit [0135.867] bct_init bctinit [0138.325] bct_init bctinit [0138.328] bct_init bctinit [0140.782] bct_init bctinit [0140.784] bct_init bctinit [0142.230] bct_init bctinit [0142.233] bct_init bctinit [0142.813] partition APP write successful. [0142.819] Writing TBC partition [0142.822] bct_init bctinit [0142.852] bct_init bctinit [0142.855] bct_init bctinit [0142.862] partition TBC write successful. [0142.868] Writing EBT partition [0142.871] bct_init bctinit [0142.909] bct_init bctinit [0142.911] bct_init bctinit [0142.921] partition EBT write successful. [0142.949] Writing BPF partition [0142.952] bct_init bctinit [0142.958] bct_init bctinit [0142.960] bct_init bctinit [0142.965] partition BPF write successful. [0142.971] Writing WB0 partition [0142.974] bct_init bctinit [0142.979] bct_init bctinit [0142.981] bct_init bctinit [0142.986] partition WB0 write successful. [0142.992] Writing RP1 partition [0142.995] bct_init bctinit [0143.015] bct_init bctinit [0143.018] bct_init bctinit [0143.028] partition RP1 write successful. [0143.034] Writing TOS partition [0143.037] bct_init bctinit [0143.042] bct_init bctinit [0143.045] bct_init bctinit [0143.050] partition TOS write successful. [0143.056] Writing EKS partition [0143.059] bct_init bctinit [0143.063] bct_init bctinit [0143.065] bct_init bctinit [0143.069] partition EKS write successful. [0143.078] Writing BMP partition [0143.081] bct_init bctinit [0143.489] bct_init bctinit [0143.492] bct_init bctinit [0143.691] partition BMP write successful. [0143.698] Writing LNX partition [0143.701] bct_init bctinit [0143.724] bct_init bctinit [0143.727] bct_init bctinit [0143.737] partition LNX write successful. [0143.743] Writing DTB partition [0143.746] bct_init bctinit [0143.766] bct_init bctinit [0143.769] bct_init bctinit [0143.779] partition DTB write successful. [0143.816] Writing BCT partition [0143.844] bct_init bctinit [0143.932] partition BCT write successful. [0143.946] Change state to cold boot mode [0143.950] Flushing data to stroage [0000.183] [TegraBoot] (version 00.00.2014.50-mobile-6987b70e) [0000.188] Processing in cold boot mode Bootloader 2 [0000.193] A02 Bootrom Patch rev = 63 [0000.196] Power-up reason: software reset [0000.200] No Battery Present [0000.202] RamCode = 0 [0000.205] Platform has Ddr4 type ram [0000.208] max77620 disabling SD1 Remote Sense [0000.212] Setting Ddr voltage to 1125mv [0000.216] Serial Number of Pmic Max77663: 0x60ead [0000.224] Entering ramdump check [0000.227] Get RamDumpCarveOut = 0x0 [0000.230] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8 [0000.235] Last reboot was clean, booting normally! [0000.240] Sdram initialization is successful [0000.244] SecureOs Carveout Base=0xff800000 Size=0x00800000 [0000.249] GSC1 Carveout Base=0xff700000 Size=0x00100000 [0000.255] GSC2 Carveout Base=0xff600000 Size=0x00100000 [0000.260] GSC3 Carveout Base=0xff500000 Size=0x00100000 [0000.265] GSC4 Carveout Base=0xff400000 Size=0x00100000 [0000.270] GSC5 Carveout Base=0xff300000 Size=0x00100000 [0000.275] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000 [0000.280] Lp0 Carveout Base=0xff2bf000 Size=0x00001000 [0000.296] RamDump Carveout Base=0xff23f000 Size=0x00080000 [0000.301] Platform-DebugCarveout: 0 [0000.304] Nck Carveout Base=0xff03f000 Size=0x00200000 [0000.309] Non secure mode, and RB not enabled. [0000.350] Using GPT Primary to query partitions [0000.355] Loading Tboot-CPU binary [0000.404] Verifying TBC in OdmNonSecureSBK mode [0000.413] Bootloader load address is 0xa0000000, entry address is 0xa0000258 [0000.420] Bootloader downloaded successfully. [0000.424] Downloaded Tboot-CPU binary to 0xa0000258 [0000.429] MAX77620_GPIO1 Configured. [0000.433] MAX77620_GPIO5 Configured. [0000.436] CPU power rail is up [0000.439] CPU clock enabled [0000.443] Performing RAM repair [0000.446] Updating A64 Warmreset Address to 0xa00002e9 [0000.451] Loading NvTbootBootloaderDTB [0000.545] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode [0000.676] Bootloader DTB Load Address: 0x83000000 [0000.680] Loading NvTbootKernelDTB [0000.775] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode [0000.905] Kernel DTB Load Address: 0x83100000 [0000.910] Loading cboot binary [0001.003] Verifying EBT in OdmNonSecureSBK mode [0001.040] Bootloader load address is 0x92c00000, entry address is 0x92c00258 [0001.047] Bootloader downloaded successfully. [0001.051] GPT: Partition NOT found ! [0001.054] Find Partition via GPT Failed [0001.058] Find Partition via PT Failed [0001.062] function NvTbootGetBinaryOffsets: 0x1 error [0001.066] Error in NvTbootLoadBinary: 0x1 ! [0001.070] Next binary entry address: 0x92c00258 [0001.075] BoardId: 2180 [0001.080] dram memory type is 3 [0001.084] WB0 init successful [0001.110] Bpmp FW successfully loaded [0001.113] Set NvDecSticky Bits [0001.116] GSC1 address : ff700000 [0001.120] GSC2 address ff63fffc value c0edbbcc [0001.125] GSC2 address : ff600000 [0001.128] GSC3 address : ff500000 [0001.132] GSC4 address : ff400000 [0001.136] GSC5 address : ff300000 [0001.139] GSC MC Settings done [0001.143] TOS plaintext Image length 32848 [0001.146] Monitor size 32848 [0001.149] OS size 0 [0001.153] *** Secure OS image signature not verified *** [0001.158] Loading and Validation of Secure OS Successful [0001.163] NvTbootPackSdramParams: start. [0001.168] NvTbootPackSdramParams: done. [0001.172] Tegraboot started after 162584 us [0001.176] Basic modules init took 946704 us [0001.180] Sec Bootdevice Read Time = 355 ms, Read Size = 15771 KB [0001.185] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB [0001.191] Next stage binary read took 732 us [0001.195] Carveout took -6646 us [0001.198] CPU initialization took 96711 us [0001.202] Total time taken by TegraBoot 1037501 us [0001.207] Starting CPU & Halting co-processor 64NOTICE: BL31: v1.2(release):e1e4477 NOTICE: BL31: Built : 20:39:55, Mar 1 2018 NOTICE: Trusty image missing. ERROR: Error initializing runtime service trusty_fast [0001.347] RamCode = 0 [0001.369] LPDDR4 Training: Read DT: Number of tables = 10 [0001.374] EMC Training (SRC-freq: 204000; DST-freq: 408000) [0001.380] EMC Training Successful [0001.383] EMC Training (SRC-freq: 204000; DST-freq: 665600) [0001.389] EMC Training Successful [0001.392] EMC Training (SRC-freq: 204000; DST-freq: 800000) [0001.403] EMC Training Successful [0001.406] EMC Training (SRC-freq: 204000; DST-freq: 1065600) [0001.429] EMC Training Successful [0001.432] EMC Training (SRC-freq: 204000; DST-freq: 1331200) [0001.454] EMC Training Successful [0001.457] EMC Training (SRC-freq: 204000; DST-freq: 1600000) [0001.476] EMC Training Successful [0001.480] Switching to 800000 KHz Success [0001.490] RamCode = 0 [0001.493] DT Write: emc-table@40800 succeeded [0001.499] DT Write: emc-table@68000 succeeded [0001.505] DT Write: emc-table@102000 succeeded [0001.512] DT Write: emc-table@204000 succeeded [0001.518] DT Write: emc-table@408000 succeeded [0001.524] DT Write: emc-table@665600 succeeded [0001.530] DT Write: emc-table@800000 succeeded [0001.536] DT Write: emc-table@1065600 succeeded [0001.542] DT Write: emc-table@1331200 succeeded [0001.548] DT Write: emc-table@1600000 succeeded [0001.553] LPDDR4 Training: Write DT: Number of tables = 10 [0001.597] [0001.598] Debug Init done [0001.601] Marked DTB cacheable [0001.603] Bootloader DTB loaded at 0x83000000 [0001.608] Marked DTB cacheable [0001.611] Kernel DTB loaded at 0x83100000 [0001.615] DeviceTree Init done [0001.634] Pinmux applied successfully [0001.640] gicd_base: 0x50041000 [0001.645] gicc_base: 0x50042000 [0001.648] Interrupts Init done [0001.653] Using base:0x60005008 & irq:33 for tick-timer [0001.658] Using base:0x60005000 for delay-timer [0001.663] platform_init_timer: DONE [0001.666] Timer(tick) Init done [0001.671] osc freq = 38400 khz [0001.677] [0001.678] welcome to cboot [0001.680] [0001.682] Cboot Version: 00.00.2014.50-t210-e831cf53 [0001.686] calling constructors [0001.689] initializing heap [0001.692] initializing threads [0001.695] initializing timers [0001.698] creating bootstrap completion thread [0001.702] top of bootstrap2() [0001.705] CPU: ARM Cortex A57 [0001.708] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000 [0001.713] initializing platform [0001.749] config for ddr50 mode completed [0001.753] sdmmc bdev is already initialized [0001.757] Enable APE clock [0001.760] Un-powergate APE partition [0001.763] of_register: registering tegra_udc to of_hal [0001.768] of_register: registering inv20628-driver to of_hal [0001.774] of_register: registering ads1015-driver to of_hal [0001.779] of_register: registering lp8557-bl-driver to of_hal [0001.785] of_register: registering bq2419x_charger to of_hal [0001.791] of_register: registering cpc to of_hal [0001.795] of_register: registering bq27441_fuel_gauge to of_hal [0001.815] gpio framework initialized [0001.819] of_register: registering tca9539_gpio to of_hal [0001.824] of_register: registering tca9539_gpio to of_hal [0001.829] of_register: registering i2c_bus_driver to of_hal [0001.835] of_register: registering i2c_bus_driver to of_hal [0001.840] of_register: registering i2c_bus_driver to of_hal [0001.846] pmic framework initialized [0001.849] of_register: registering max77620_pmic to of_hal [0001.855] regulator framework initialized [0001.859] of_register: registering tegra_xhci to of_hal [0001.864] initializing target [0001.873] gpio_driver_register: register 'tegra_gpio_driver' driver [0001.885] fixed regulator driver initialized [0001.963] initializing OF layer [0001.966] NCK carveout not present [0001.969] Skipping dts_overrides [0001.973] of_children_init: Ops found for compatible string nvidia,tegra210-xhci [0001.982] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.013] I2C Bus Init done [0002.016] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.031] I2C Bus Init done [0002.033] of_children_init: Ops found for compatible string ti,tca9539 [0002.048] tca9539_init: i2c bus: 2, slave addr: 0xe8 [0002.053] gpio_driver_register: register 'tca9539_gpio_driver' driver [0002.060] of_children_init: Ops found for compatible string ti,tca9539 [0002.074] tca9539_init: i2c bus: 2, slave addr: 0xee [0002.079] gpio_driver_register: register 'tca9539_gpio_driver' driver [0002.086] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.101] I2C Bus Init done [0002.103] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.119] I2C Bus Init done [0002.121] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.136] I2C Bus Init done [0002.139] of_children_init: Ops found for compatible string maxim,max77620 [0002.155] max77620_init using irq 118 [0002.159] register 'maxim,max77620' pmic [0002.164] gpio_driver_register: register 'max77620-gpio' driver [0002.170] of_children_init: Ops found for compatible string nvidia,tegra210-i2c [0002.185] I2C Bus Init done [0002.191] NCK carveout not present [0002.194] shim_invoke: No NCT, Calling dts updates [0002.215] Find /i2c@7000c000's alias i2c0 [0002.219] get eeprom at 1-a2, size 256, type 0 [0002.223] get eeprom at 1-ae, size 256, type 0 [0002.239] Find /i2c@7000c400's alias i2c1 [0002.242] get eeprom at 2-a0, size 256, type 0 [0002.258] Find /i2c@7000c500's alias i2c2 [0002.262] get eeprom at 3-a0, size 256, type 0 [0002.266] get eeprom at 3-ae, size 256, type 0 [0002.278] Find /host1x/i2c@546c0000's alias i2c6 [0002.282] get eeprom at 7-a8, size 256, type 0 [0002.287] pm_ids_update: Updating 1,a2, size 256, type 0 [0002.292] I2C slave not started [0002.295] I2C write failed [0002.298] Writing offset failed [0002.301] eeprom_init: EEPROM read failed [0002.305] pm_ids_update: eeprom init failed [0002.309] pm_ids_update: Updating 1,ae, size 256, type 0 [0002.314] I2C slave not started [0002.317] I2C write failed [0002.320] Writing offset failed [0002.323] eeprom_init: EEPROM read failed [0002.327] pm_ids_update: eeprom init failed [0002.331] pm_ids_update: Updating 2,a0, size 256, type 0 [0002.336] I2C slave not started [0002.339] I2C write failed [0002.342] Writing offset failed [0002.345] eeprom_init: EEPROM read failed [0002.349] pm_ids_update: eeprom init failed [0002.353] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.383] pm_ids_update: The pm board id is 2180-1000-100 [0002.392] Adding plugin-manager/ids/2180-1000-100=/i2c@7000c500:module@0x50 [0002.403] pm_ids_update: pm id update successful [0002.407] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.437] pm_ids_update: The pm board id is 2597-0000-302 [0002.445] Adding plugin-manager/ids/2597-0000-302=/i2c@7000c500:module@0x57 [0002.454] pm_ids_update: pm id update successful [0002.459] pm_ids_update: Updating 7,a8, size 256, type 0 [0002.491] pm_ids_update: The pm board id is 3326-1000-100 [0002.499] Adding plugin-manager/ids/3326-1000-100=/host1x/i2c@546c0000:module@0x54 [0002.510] pm_ids_update: pm id update successful [0002.545] updating /chosen/nvidia,wifi-mac node 00:04:4b:5a:e6:6c [0002.555] updating /chosen/nvidia,bluetooth-mac node 00:04:4b:5a:e6:6d [0002.564] updating /chosen/nvidia,ethernet-mac node 00:04:4b:5a:e6:6e [0002.571] Plugin Manager: Parse ODM data 0x00084000 [0002.608] Find /i2c@7000c000's alias i2c0 [0002.612] get eeprom at 1-a2, size 256, type 0 [0002.617] get eeprom at 1-ae, size 256, type 0 [0002.632] Find /i2c@7000c400's alias i2c1 [0002.636] get eeprom at 2-a0, size 256, type 0 [0002.651] Find /i2c@7000c500's alias i2c2 [0002.655] get eeprom at 3-a0, size 256, type 0 [0002.660] get eeprom at 3-ae, size 256, type 0 [0002.672] Find /host1x/i2c@546c0000's alias i2c6 [0002.676] get eeprom at 7-a8, size 256, type 0 [0002.681] pm_ids_update: Updating 1,a2, size 256, type 0 [0002.686] I2C slave not started [0002.689] I2C write failed [0002.691] Writing offset failed [0002.694] eeprom_init: EEPROM read failed [0002.698] pm_ids_update: eeprom init failed [0002.703] pm_ids_update: Updating 1,ae, size 256, type 0 [0002.708] I2C slave not started [0002.711] I2C write failed [0002.713] Writing offset failed [0002.716] eeprom_init: EEPROM read failed [0002.720] pm_ids_update: eeprom init failed [0002.725] pm_ids_update: Updating 2,a0, size 256, type 0 [0002.730] I2C slave not started [0002.733] I2C write failed [0002.735] Writing offset failed [0002.739] eeprom_init: EEPROM read failed [0002.742] pm_ids_update: eeprom init failed [0002.747] pm_ids_update: Updating 3,a0, size 256, type 0 [0002.777] pm_ids_update: The pm board id is 2180-1000-100 [0002.785] Adding plugin-manager/ids/2180-1000-100=/i2c@7000c500:module@0x50 [0002.792] pm_ids_update: pm id update successful [0002.796] pm_ids_update: Updating 3,ae, size 256, type 0 [0002.826] pm_ids_update: The pm board id is 2597-0000-302 [0002.834] Adding plugin-manager/ids/2597-0000-302=/i2c@7000c500:module@0x57 [0002.841] pm_ids_update: pm id update successful [0002.846] pm_ids_update: Updating 7,a8, size 256, type 0 [0002.878] pm_ids_update: The pm board id is 3326-1000-100 [0002.886] Adding plugin-manager/ids/3326-1000-100=/host1x/i2c@546c0000:module@0x54 [0002.894] pm_ids_update: pm id update successful [0002.928] Chip UID is 00000001640d06c82400000008010200 [0002.936] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 OS=l4t fbcon=map:0 net.ifnames=0 androidboot.modem=none androidboot.serialno=03218160291930000201 androidboot.security=non-secure [0002.960] Add serial number:03218160291930000201 as DT property [0002.968] calling apps_init() [0002.973] Found 19 GPT partitions in "sdmmc3_user" [0002.977] Proceeding to Cold Boot [0002.980] starting app android_boot_app [0002.984] Device state: unlocked [0002.987] display console init [0003.006] No valid panel node found [0003.015] enabling 'vdd-hdmi' regulator [0003.036] DT entry for leds-pwm not found [0003.040] hdmi cable not connected [0003.044] is_hdmi_needed: HDMI not connected, returning false [0003.049] set_instance_and_out_type: invalid out_type [0003.054] display_console_init: No display init [0003.065] Gpio keyboard init success [0003.068] bct_init bctinit [0003.071] bct_init bctinit [0003.076] bct_init bctinit [0003.079] bct_init bctinit [0003.279] decompressor handler not found [0003.283] display_resolution: No display init [0003.287] Failed to retrieve display resolution [0003.291] Could not load/initialize BMP blob...ignoring [0003.297] bl_battery_charging: connected to external power supply [0003.308] display_console_ioctl: No display init [0003.312] switch_backlight failed [0003.316] bct_init bctinit [0003.318] device_query_partition_size: failed to open partition sdmmc3_user:MSC ! [0003.326] MSC Partition not found [0003.329] bct_init bctinit [0003.332] bct_init bctinit [0003.335] blob_init: USP partition does not have valid Blob [0003.341] kfs_getpartname: name = LNX [0003.344] Loading kernel from LNX [0003.354] Verifying boot image in OdmNonSecureSBK mode [0003.376] kernel load address: 0x80080000, size: 506749 bytes [0003.381] ramdisk load address: 0x84100000, size: 0 bytes [0003.387] load kernel from storage [0003.391] decompressor handler not found [0003.401] Successfully loaded kernel and ramdisk images [0003.409] display_resolution: No display init [0003.413] Failed to retrieve display resolution [0003.418] bmp blob is not loaded and initialized [0003.422] Failed to display boot-logo [0003.426] NCK carveout not present [0003.429] Skipping dts_overrides [0003.432] NCK carveout not present [0003.436] shim_invoke: No NCT, Calling dts updates [0003.457] Find /i2c@7000c000's alias i2c0 [0003.461] get eeprom at 1-a2, size 256, type 0 [0003.465] get eeprom at 1-ae, size 256, type 0 [0003.480] Find /i2c@7000c400's alias i2c1 [0003.484] get eeprom at 2-a0, size 256, type 0 [0003.500] Find /i2c@7000c500's alias i2c2 [0003.504] get eeprom at 3-a0, size 256, type 0 [0003.508] get eeprom at 3-ae, size 256, type 0 [0003.520] Find /host1x/i2c@546c0000's alias i2c6 [0003.524] get eeprom at 7-a8, size 256, type 0 [0003.529] pm_ids_update: Updating 1,a2, size 256, type 0 [0003.534] I2C slave not started [0003.537] I2C write failed [0003.540] Writing offset failed [0003.543] eeprom_init: EEPROM read failed [0003.546] pm_ids_update: eeprom init failed [0003.551] pm_ids_update: Updating 1,ae, size 256, type 0 [0003.556] I2C slave not started [0003.559] I2C write failed [0003.562] Writing offset failed [0003.565] eeprom_init: EEPROM read failed [0003.568] pm_ids_update: eeprom init failed [0003.573] pm_ids_update: Updating 2,a0, size 256, type 0 [0003.578] I2C slave not started [0003.581] I2C write failed [0003.584] Writing offset failed [0003.587] eeprom_init: EEPROM read failed [0003.591] pm_ids_update: eeprom init failed [0003.595] pm_ids_update: Updating 3,a0, size 256, type 0 [0003.625] pm_ids_update: The pm board id is 2180-1000-100 [0003.634] Adding plugin-manager/ids/2180-1000-100=/i2c@7000c500:module@0x50 [0003.644] pm_ids_update: pm id update successful [0003.649] pm_ids_update: Updating 3,ae, size 256, type 0 [0003.679] pm_ids_update: The pm board id is 2597-0000-302 [0003.687] Adding plugin-manager/ids/2597-0000-302=/i2c@7000c500:module@0x57 [0003.696] pm_ids_update: pm id update successful [0003.700] pm_ids_update: Updating 7,a8, size 256, type 0 [0003.733] pm_ids_update: The pm board id is 3326-1000-100 [0003.741] Adding plugin-manager/ids/3326-1000-100=/host1x/i2c@546c0000:module@0x54 [0003.752] pm_ids_update: pm id update successful [0003.787] updating /chosen/nvidia,wifi-mac node 00:04:4b:5a:e6:6c [0003.796] updating /chosen/nvidia,bluetooth-mac node 00:04:4b:5a:e6:6d [0003.806] updating /chosen/nvidia,ethernet-mac node 00:04:4b:5a:e6:6e [0003.812] Plugin Manager: Parse ODM data 0x00084000 [0003.836] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 OS=l4t fbcon=map:0 net.ifnames=0 androidboot.modem=none androidboot.serialno=03218160291930000201 androidboot.security=non-secure [0003.860] Add serial number:03218160291930000201 as DT property [0003.869] Updated bpmp info to DTB [0003.876] Updated initrd info to DTB [0003.879] "proc-board" doesn't exist, creating [0003.887] Updated board info to DTB [0003.890] "pmu-board" doesn't exist, creating [0003.898] Updated board info to DTB [0003.901] "display-board" doesn't exist, creating [0003.908] Updated board info to DTB [0003.912] "reset" doesn't exist, creating [0003.917] Updated reset info to DTB [0003.920] display_console_ioctl: No display init [0003.925] display_console_ioctl: No display init [0003.929] display_console_ioctl: No display init [0003.934] Cmdline: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 OS=l4t fbcon=map:0 net.ifnames=0 androidboot.modem=none androidboot.serialno=03218160291930000201 androidboot.security=non-secure tegraid=21.1.2.0.0 ddr_die=2048M@2048M ddr_die=2048M@4096M section=256M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff2bf000 nvdumper_reserved=0xff23f000 core_edp_mv=1125 core_edp_ma=4000 gpt [0003.990] Updated bootarg info to DTB [0003.998] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7 [0004.005] Updated memory info to DTB [0004.014] set vdd_core voltage to 1125 mv [0004.018] setting 'vdd-core' regulator to 1125000 micro volts [0004.023] nvdumper Carveout: Base = 0xff23f000 and Size = 0x80000 [0004.030] bct_init bctinit [0004.033] bct_init bctinit [0004.110] Starting Bpmp FW [0004.113] BPMP-FW Carveout: Base = 0xff2c0000 and Size = 0x40000 U-Boot 2016.07-g9c3b9a4 (Mar 01 2018 - 20:40:15 -0800) TEGRA210 Model: NVIDIA P2371-2180 Board: NVIDIA P2371-2180 DRAM: 4 GiB MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2 ... 1 ... 0 Card did not respond to voltage select! switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:1... Found /boot/extlinux/extlinux.conf Retrieving file: /boot/extlinux/extlinux.conf 223 bytes read in 66 ms (2.9 KiB/s) p2371-2180 eMMC boot options 1:.primary kernel Enter choice: 1:.primary kernel Retrieving file: /boot/initrd 0 bytes read in 67 ms (0 Bytes/s) Retrieving file: /boot/Image 21193144 bytes read in 533 ms (37.9 MiB/s) append: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 OS=l4t fbcon=map:0 net.ifnames=0 androidboot.modem=none androidboot.serialno=03218160291930000201 androidboot.security=non-secure tegraid=21.1.2.0.0 ddr_die=2048M@2048M ddr_die=2048M@4096M section=256M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff2bf000 nvdumper_reserved=0xff23f000 core_edp_mv=1125 core_edp_ma=4000 gpt root=/dev/mmcblk0p1 rw rootwait ## Flattened Device Tree blob at 83100000 Booting using the fdt blob at 0x83100000 reserving fdt memory region: addr=80000000 size=20000 Using Device Tree in place at 0000000083100000, end 00000000831b0c03 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.38-tegra (buildbrain@mobile-u64-638) (gcc version 4.8.5 (GCC) ) #1 SMP PREEMPT Thu Mar 1 20:44:58 PST 2018 [ 0.000000] Boot CPU: AArch64 Processor [411fd071] [ 0.000000] Reserved memory: initialized node iram-carveout, compatible id nvidia,iram-carveout [ 0.000000] Reserved memory: initialized node ramoops_carveout, compatible id nvidia,ramoops [ 0.000000] cma: Reserved 16 MiB at 0x00000000fdc00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] PERCPU: Embedded 17 pages/cpu @ffffffc0ffe10000 s31616 r8192 d29824 u69632 [ 0.000000] CPU features: enabling workaround for ARM erratum 832075 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1027072 [ 0.000000] Kernel command line: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 OS=l4t fbcon=map:0 net.ifnames=0 androidboot.modem=none androidboot.serialno=03218160291930000201 androidboot.security=non-secure tegraid=21.1.2.0.0 ddr_die=2048M@2048M ddr_die=2048M@4096M section=256M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff2bf000 nvdumper_reserved=0xff23f000 core_edp_mv=1125 core_edp_ma=4000 gpt root=/dev/mmcblk0p1 rw rootwait [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Memory: 4061768K/4173824K available (10945K kernel code, 2068K rwdata, 6364K rodata, 1208K init, 665K bss, 95672K reserved, 16384K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000 ( 246 GB) [ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum) [ 0.000000] 0xffffffbdc2000000 - 0xffffffbdc6000000 ( 64 MB actual) [ 0.000000] fixed : 0xffffffbffa7fd000 - 0xffffffbffac00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000 ( 16 MB) [ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc100000000 ( 4096 MB) [ 0.000000] .init : 0xffffffc001168000 - 0xffffffc001296000 ( 1208 KB) [ 0.000000] .text : 0xffffffc000080000 - 0xffffffc001167d74 ( 17312 KB) [ 0.000000] .data : 0xffffffc0012b1000 - 0xffffffc0014b61b8 ( 2069 KB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] .Build-time adjustment of leaf fanout to 64. [ 0.000000] .RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller [ 0.000000] enable_t210_agic_clks:106 ape clocked & reset cleared [ 0.000000] t210 clock_and_reset probe [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] clk_cbus_recalc_rate: no gbus parent [ 0.000000] kmemleak: Kernel memory leak detector disabled [ 0.000000] Architected cp15 timer(s) running at 19.20MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.001815] Console: colour dummy device 80x25 [ 0.002775] console [tty0] enabled [ 0.002808] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800) [ 0.002843] pid_max: default: 32768 minimum: 301 [ 0.002931] Security Framework initialized [ 0.002954] SELinux: Initializing. [ 0.003061] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.003086] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.003763] Initializing cgroup subsys io [ 0.003796] Initializing cgroup subsys memory [ 0.003835] Initializing cgroup subsys devices [ 0.003861] Initializing cgroup subsys freezer [ 0.003885] Initializing cgroup subsys net_cls [ 0.003908] Initializing cgroup subsys perf_event [ 0.003935] Initializing cgroup subsys net_prio [ 0.003963] Initializing cgroup subsys pids [ 0.003988] Initializing cgroup subsys debug [ 0.004291] CPU0 ipc=1024 [ 0.004328] CPU1 ipc=1024 [ 0.004362] CPU2 ipc=1024 [ 0.004395] CPU3 ipc=1024 [ 0.004456] ASID allocator initialised with 65536 entries [ 0.030420] tegra-id: chipid=22117. [ 0.030452] tegra-id: opt_subrevision=0. [ 0.030485] Tegra Speedo/IDDQ fuse revision 4 [ 0.030507] Tegra: CPU Speedo ID 7, SoC Speedo ID 0, GPU Speedo ID 2 [ 0.030529] Tegra: CPU Process ID 0, SoC Process ID 0, GPU Process ID 0 [ 0.030551] Tegra: CPU Speedo Value 2014, SoC Speedo Value 1917, GPU Speedo Value 2012 [ 0.030581] Tegra: CPU IDDQ Value 1648, SoC IDDQ Value 1828, GPU IDDQ Value 2115 [ 0.030626] Tegra Revision: A02 SKU: 0x17 CPU Process: 0 SoC Process: 0 [ 0.032179] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.4/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/jetson/kernel-dts/tegra210-jetson-tx1-p2597-2180-a01-devkit.dts [ 0.032247] DTB Build time: Mar 1 2018 20:46:06 [ 0.048778] CPU1: Booted secondary processor [411fd071] [ 0.060739] CPU2: Booted secondary processor [411fd071] [ 0.072738] CPU3: Booted secondary processor [411fd071] [ 0.072827] Brought up 4 CPUs [ 0.072903] SMP: Total of 4 processors activated. [ 0.072927] CPU: All CPU(s) started at EL2 [ 0.072968] alternatives: patching kernel code [ 0.075488] devtmpfs: initialized [ 0.144284] Initilizing CustomIPI irq domain [ 0.144619] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.145216] pinctrl core: initialized pinctrl subsystem [ 0.145399] OS set in device tree is not L4T. [ 0.145754] regulator-dummy: no parameters [ 0.145969] Initializing plugin-manager [ 0.146038] Plugin module not found [ 0.146244] node /plugin-manager/fragment-e3326@0 match with board 3326-* [ 0.149421] Adding domain ape-pd to PM domain mc-clk-pd [ 0.149470] Adding domain adsp-pd to PM domain ape-pd [ 0.154539] NET: Registered protocol family 16 [ 0.156335] console [pstore-1] enabled [ 0.156359] pstore: Registered ramoops as persistent store backend [ 0.156384] ramoops: attached 0x200000@0xb0000000, ecc: 0/0 [ 0.168229] cpuidle: using governor ladder [ 0.180219] cpuidle: using governor menu [ 0.180540] bpmp: mail init ok [ 0.181318] vdso: 2 pages (1 code @ ffffffc0012b9000, 1 data @ ffffffc0012b8000) [ 0.181376] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.182793] atomic_pool_init():526: DMA: preallocated 1024 KiB pool for atomic allocations [ 0.183741] tegra_powergate_init: DONE [ 0.183786] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.4/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/jetson/kernel-dts/tegra210-jetson-tx1-p2597-2180-a01-devkit.dts [ 0.183838] DTB Build time: Mar 1 2018 20:46:06 [ 0.186783] tegra_bpmp_of_clk_init: EMC proxy not found. [ 0.186823] Error: Driver 'tegra-mc' is already registered, aborting... [ 0.188326] platform tegra-carveouts: SMMU isn't ready yet [ 0.189033] platform tegra-carveouts: domain=ffffffc0fa162618 allocates as[0]=ffffffc0fa17c0a8 [ 0.189103] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver [ 0.189338] platform smmu_test: domain=ffffffc0fa162918 allocates as[0]=ffffffc0fa17c110 [ 0.189654] platform 70016000.bpmp: domain=ffffffc0fa162c18 allocates as[0]=ffffffc0fa17c178 [ 0.190362] bpmp: ping status is 0 [ 0.190472] bpmp 70016000.bpmp: firmware tag is 1e4b302fc0f866f97885165cf8b395ac [ 0.190728] bpmp 70016000.bpmp: probe ok [ 0.191373] mc: mapped MMIO address: 0xffffff800007e000 -> 0x70019000 [ 0.191480] mc: mapped MMIO address: 0xffffff80000b6000 -> 0x7001c000 [ 0.191580] mc: mapped MMIO address: 0xffffff80000dc000 -> 0x7001d000 [ 0.191670] mc-err: Set intmask: 0x23d40 [ 0.202575] GPIO line 58 (wlan-default-input-h2) hogged as input [ 0.202627] GPIO line 65 (wlan-default-input-i1) hogged as input [ 0.202676] GPIO line 56 (wlan-default-output-high-h0) hogged as output/high [ 0.202721] GPIO line 64 (wlan-default-output-high-i0) hogged as output/high [ 0.202765] GPIO line 66 (wlan-default-output-high) hogged as output/high [ 0.202811] GPIO line 148 (cam0-rst) hogged as output/low [ 0.202852] GPIO line 151 (cam0-pwdn) hogged as output/low [ 0.202894] GPIO line 149 (cam1-rst) hogged as output/low [ 0.202937] GPIO line 152 (cam1-pwdn) hogged as output/low [ 0.203044] gpiochip_add_data: registered GPIOs 0 to 255 on device: tegra-gpio [ 0.205540] platform 70006000.serial: domain=ffffffc0fa23a118 allocates as[0]=ffffffc0fa17c1e0 [ 0.206636] platform sound: domain=ffffffc0fa23aa18 allocates as[0]=ffffffc0fa17c248 [ 0.209026] platform tegradc.1: domain=ffffffc0fa23fc18 allocates as[0]=ffffffc0fa17c2b0 [ 0.211559] platform 57000000.gpu: domain=ffffffc0fa246f18 allocates as[0]=ffffffc0fa17c318 [ 0.211640] platform 57000000.gpu: domain=ffffffc0fa246f18 allocates as[1]=ffffffc0fa17c380 [ 0.211716] platform 57000000.gpu: domain=ffffffc0fa246f18 allocates as[2]=ffffffc0fa17c3e8 [ 0.211787] platform 57000000.gpu: domain=ffffffc0fa246f18 allocates as[3]=ffffffc0fa17c450 [ 0.212605] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled. [ 0.212651] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present [ 0.212678] tegra-pmc: ### PMC reset source: Software reset [ 0.212700] tegra-pmc: ### PMC reset status reg: 0x3 [ 0.256351] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered [ 0.256388] tegra-pmc: Clear bootloader IO dpd settings [ 0.256418] tegra-pmc 7000e400.pmc: IO padctrl driver initialized [ 0.256488] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands [ 0.259653] platform 1003000.pcie-controller: domain=ffffffc0fa2e6018 allocates as[0]=ffffffc0fa17c4b8 [ 0.261913] platform sdhci-tegra.3: domain=ffffffc0fa2ed118 allocates as[0]=ffffffc0fa17c520 [ 0.262514] platform sdhci-tegra.0: domain=ffffffc0fa2ed518 allocates as[0]=ffffffc0fa17c588 [ 0.269450] vdd-ac-bat: 5000 mV [ 0.270645] vdd-cpu-fixed: 1000 mV [ 0.274563] irq: no irq domain found for /soctherm@0x700E2000 ! [ 0.274906] irq: no irq domain found for /soctherm@0x700E2000 ! [ 0.297448] ACPI: Interpreter disabled. [ 0.298258] SCSI subsystem initialized [ 0.298548] usbcore: registered new interface driver usbfs [ 0.298628] usbcore: registered new interface driver hub [ 0.298726] usbcore: registered new device driver usb [ 0.301716] gpiochip_add_data: registered GPIOs 496 to 511 on device: tca9539 [ 0.303167] gpiochip_add_data: registered GPIOs 480 to 495 on device: tca9539 [ 0.306304] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8 [ 0.308240] GPIO line 474 (spmic-default-output-high) hogged as output/high [ 0.308364] gpiochip_add_data: registered GPIOs 472 to 479 on device: max77620-gpio [ 0.312348] vdd-core: 600 <--> 1400 mV at 1125 mV [ 0.316344] vddio-ddr: at 1125 mV [ 0.317199] vdd-pre-reg: 1350 mV [ 0.320214] vdd-1v8: 1800 mV [ 0.324215] avdd-sys: 1200 mV [ 0.328214] vdd-pex: 1050 mV [ 0.328833] vddio-sdmmc1: 1800 <--> 3300 mV at 3300 mV [ 0.329705] vdd-cam-hv: 2800 mV [ 0.332213] vdd-rtc: 850 mV [ 0.333073] avdd-ts-hv: 3300 mV [ 0.333956] vdd-ts: 1800 mV [ 0.336215] vdd-gen-pll-edp: 1050 mV [ 0.340214] vdd-hdmi-dp: 1050 mV [ 0.340863] max77620 4-003c: max77620 probe successful [ 0.342852] media: Linux media interface: v0.10 [ 0.342928] Linux video capture interface: v2.00 [ 0.350337] tegra210-emc 7001b000.memory-controller: validated EMC DFS table [ 0.350683] Advanced Linux Sound Architecture Driver Initialized. [ 0.353452] tegra210_dvfs: no clock found for sdmmc2_ddr [ 0.353501] tegra210_dvfs: no clock found for sdmmc4_ddr [ 0.353584] tegra210_dvfs: no clock found for sdmmc1_ddr [ 0.353626] tegra210_dvfs: no clock found for sdmmc3_ddr [ 0.356597] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe [ 0.360220] vdd-3v3: 3300 mV [ 0.364215] max77620-gpio7: 1050 mV [ 0.364524] lcd-bl-en: 1800 mV [ 0.364824] en-vdd-sd: 3300 mV [ 0.365511] en-vdd-cam: 1800 mV [ 0.368215] vdd-sys-boost: 5000 mV [ 0.368874] vdd-hdmi: 5000 mV [ 0.369121] aux-3v3: 3300 mV [ 0.369351] snsr_pm: 3300 mV [ 0.372218] vdd-disp-3v0: 3000 mV [ 0.372905] vdd-fan: 5000 mV [ 0.373195] usb-vbus1: 5000 mV [ 0.373847] en-vdd-ts-1v8: 1800 mV [ 0.374495] en-vdd-ts-hv-3v3: 3300 mV [ 0.375318] en-vdd-disp-3v3: 3300 mV [ 0.375985] en-mdm-pwr-3v7: 3700 mV [ 0.376827] en-vdd-disp-1v8: 1800 mV [ 0.377471] en-vdd-cam-hv-2v8: 2800 mV [ 0.377758] rtl-5v0: 5000 mV [ 0.378042] en-usb-vbus2: 5000 mV [ 0.378700] en-vdd-cam-1v2: 1200 mV [ 0.379002] en-vdd-vcm-2v8: 2800 mV [ 0.379649] en-vdd-cam-1v2-alt: 1200 mV [ 0.382429] extcon-gpio-states extcon:extcon@1: Cable state 1 [ 0.383461] clocksource: Switched to clocksource arch_sys_counter [ 0.427687] nvmap_heap_init: nvmap_heap_init: created heap block cache [ 0.428049] nvmap_page_pool_init: Total RAM pages: 1019538 [ 0.428079] nvmap_page_pool_init: nvmap page pool size: 127442 pages (497 MB) [ 0.428184] nvmap_background_zero_thread: PP zeroing thread starting. [ 0.428374] misc nvmap: iram :dma coherent mem declare 0x0000000040001000,258048 [ 0.428508] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB) [ 0.429172] pnp: PnP ACPI: disabled [ 0.440940] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm [ 0.442766] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm [ 0.443165] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm [ 0.443358] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm [ 0.444996] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type Tdiode_tegra [ 0.445251] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type PMIC-Die [ 0.445474] thermal thermal_zone6: Registering thermal zone thermal_zone6 for type Tboard_tegra [ 0.446757] isomgr_init(): iso emc max clk=1600000KHz [ 0.446782] isomgr_init(): max_iso_bw=11520000KB [ 0.446915] NET: Registered protocol family 2 [ 0.447515] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.447720] TCP bind hash table entries: 32768 (order: 7, 524288 bytes) [ 0.447983] TCP: Hash tables configured (established 32768 bind 32768) [ 0.448090] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.448157] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.448396] NET: Registered protocol family 1 [ 0.448730] RPC: Registered named UNIX socket transport module. [ 0.448761] RPC: Registered udp transport module. [ 0.448783] RPC: Registered tcp transport module. [ 0.448806] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.449070] Trying to unpack rootfs image as initramfs... [ 0.460118] host1x 50000000.host1x: initialized [ 0.461492] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.464580] futex hash table entries: 1024 (order: 5, 131072 bytes) [ 0.464707] audit: initializing netlink subsys (disabled) [ 0.464765] audit: type=2000 audit(0.459:1): initialized [ 0.476630] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.477120] fuse init (API version 7.23) [ 0.480181] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.480323] io scheduler noop registered [ 0.480356] io scheduler deadline registered [ 0.480550] io scheduler cfq registered (default) [ 0.486094] tegra21x-padctl-uphy 7009f000.pinctrl: padctl mmio start 0x000000007009f000 end 0x000000007009ffff [ 0.486143] tegra21x-padctl-uphy 7009f000.pinctrl: TEGRA_FUSE_SKU_CALIB_0 0x9a6a414 [ 0.486179] tegra21x-padctl-uphy 7009f000.pinctrl: TEGRA_FUSE_USB_CALIB_EXT_0 0x4 [ 0.487658] tegra21x-padctl-uphy 7009f000.pinctrl: UTMI-0 is used by XUSB [ 0.487697] tegra21x-padctl-uphy 7009f000.pinctrl: using UTMI port 0 for otg [ 0.487727] tegra21x-padctl-uphy 7009f000.pinctrl: UTMI-2 is used by XUSB [ 0.487765] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 5, set usb3_lanes = 0x20 [ 0.487810] tegra21x-padctl-uphy 7009f000.pinctrl: USB3 port 1 maps to USB2 port 2 [ 0.487846] tegra21x-padctl-uphy 7009f000.pinctrl: UTMI-1 is used by XUSB [ 0.487881] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 6, set usb3_lanes = 0x60 [ 0.487924] tegra21x-padctl-uphy 7009f000.pinctrl: USB3 port 0 maps to USB2 port 1 [ 0.487970] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 1, set pcie_lanes = 0x2 [ 0.488019] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 2, set pcie_lanes = 0x6 [ 0.488067] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 3, set pcie_lanes = 0xe [ 0.488113] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 4, set pcie_lanes = 0x1e [ 0.488159] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 0, set pcie_lanes = 0x1f [ 0.488208] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 7, set sata_lanes = 0x80 [ 0.488635] tegra21x-padctl-uphy 7009f000.pinctrl: mailbox is not ready yet [ 0.489658] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops [ 0.490767] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000 [ 0.491532] Adding domain pcie-pd to PM domain mc-clk-pd [ 0.496269] tegra-pcie 1003000.pcie-controller: 4x1, 1x1 configuration [ 0.496338] tegra-pcie 1003000.pcie-controller: failed to get PHY: -517 [ 0.496366] tegra-pcie 1003000.pcie-controller: failed to get PHYs: -517 [ 0.499982] tsec 54500000.tsec: initialized [ 0.501138] tsec 54100000.tsecb: initialized [ 0.503885] nvdec 54480000.nvdec: initialized [ 0.508903] falcon 54340000.vic: initialized [ 0.510202] falcon 544c0000.nvenc: initialized [ 0.511155] falcon 54380000.nvjpg: initialized [ 0.513336] DC OR NODE connected to /host1x/sor1 [ 0.513438] display board info: id 0xffff, fab 0x0 [ 0.513494] panel_select fail by _node_status [ 0.513552] display board info: id 0xffff, fab 0x0 [ 0.513600] panel_select fail by _node_status [ 0.513627] generic_infoframe_type: 0x87 [ 0.513806] tegradc tegradc.1: DT parsed successfully [ 0.513866] tegradc tegradc.1: Display dc.ffffff8000980000 registered with id=0 [ 0.514714] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe [ 0.514908] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=2550000, vi_iso_bw=1500000, max_bw=2550000 [ 0.515615] display board info: id 0xffff, fab 0x0 [ 0.515669] panel_select fail by _node_status [ 0.519563] tegra-i2c 7000c700.i2c: no acknowledge from address 0x50 [ 0.520726] tegradc tegradc.1: probed [ 0.523310] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels [ 0.525410] tegra-adma 702e2000.adma: Tegra ADMA driver register 10 channels [ 0.526970] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized [ 0.527279] kfuse 7000fc00.kfuse: initialized [ 0.529293] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0 [ 0.530187] clk_cbus_round_rate: no gbus parent [ 0.530219] tegra_gpu_edp gpu_edp: unable to get max GPU freq [ 0.530749] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now [ 0.530784] vdd-cpu: 708 <--> 1322 mV at 708 mV [ 0.530851] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed [ 0.532121] vdd-gpu: applied init 1000000uV constraint [ 0.532157] vdd-gpu: 710 <--> 1320 mV at 1000 mV [ 0.532223] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed [ 0.532645] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.532769] No Device Node present for smmu client: serial8250 !! [ 0.532799] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 0.532842] No Device Node present for smmu client: serial8250 !! [ 0.532869] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 0.533953] No Device Node present for smmu client: serial8250 !! [ 0.533987] serial8250 serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 0.534035] No Device Node present for smmu client: serial8250 !! [ 0.534062] serial8250 serial8250: No iommus property found in DT node, got swgids from fixup(101004000) [ 0.534724] console [ttyS0] disabled [ 0.534800] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 320, base_baud = 25500000) is a Tegra [ 2.477680] console [ttyS0] enabled [ 2.479007] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 321, base_baud = 0) is a TEGRA_UART [ 2.479477] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 322, base_baud = 0) is a TEGRA_UART [ 2.479808] serial-tegra 70006300.serial: RX in PIO mode [ 2.479913] 70006300.serial: ttyTHS3 at MMIO 0x70006300 (irq = 323, base_baud = 0) is a TEGRA_UART [ 2.481476] Console: switching to colour frame buffer device 80x30 [ 2.486256] gk20a 57000000.gpu: platform probe failed [ 2.492842] brd: module loaded [ 2.562556] tegradc tegradc.1: fb registered [ 2.569849] loop: module loaded [ 2.576042] zram: Added device: zram0 [ 2.581989] Silicon Labs C2 port support v. 0.51.0 - (C) 2007 Rodolfo Giometti [ 2.593881] nct1008_nct72 0-004c: find device tree node, parsing dt [ 2.602452] nct1008_nct72 0-004c: starting parse dt [ 2.609627] nct1008_nct72 0-004c: success parsing dt [ 2.616997] nct1008_nct72 0-004c: success in enabling tmp451 VDD rail [ 2.660468] tmp451: Enabled overheat logging at 102.00C [ 2.667935] nct1008_nct72 0-004c: nct1008_probe: initialized [ 2.678285] THERMAL EST: found 2 subdevs [ 2.684308] THERMAL EST num_resources: 0 [ 2.690238] [THERMAL EST subdev 0] [ 2.695633] [THERMAL EST subdev 1] [ 2.701272] thermal thermal_zone7: Registering thermal zone thermal_zone7 for type thermal-fan-est [ 2.713998] THERMAL EST: thz register success. [ 2.720429] THERMAL EST: end of probe, return err: 0 [ 2.727296] tegra_profiler: Branch: Dev [ 2.732911] tegra_profiler: Version: 1.117 [ 2.738703] tegra_profiler: Samples version: 41 [ 2.744875] tegra_profiler: IO version: 22 [ 2.750565] armv8_pmu: imp: 0x41, idcode: 0x1 [ 2.756506] armv8_pmu: [0] arch: AA64 PmuV3 ARM CORTEX-A57, type: 5, ver: 0, pmu ver: 0x1 [ 2.767922] armv8_pmu: imp: 0x41, idcode: 0x1 [ 2.773965] armv8_pmu: [1] arch: AA64 PmuV3 ARM CORTEX-A57, type: 5, ver: 0, pmu ver: 0x1 [ 2.785460] armv8_pmu: imp: 0x41, idcode: 0x1 [ 2.791468] armv8_pmu: [2] arch: AA64 PmuV3 ARM CORTEX-A57, type: 5, ver: 0, pmu ver: 0x1 [ 2.803062] armv8_pmu: imp: 0x41, idcode: 0x1 [ 2.809205] armv8_pmu: [3] arch: AA64 PmuV3 ARM CORTEX-A57, type: 5, ver: 0, pmu ver: 0x1 [ 2.821098] tegra_profiler: auth: init [ 2.827124] tegra-ahci 70027000.sata: Missing devslp-active state [ 2.836012] Rounding down aligned max_sectors from 4294967295 to 4294967288 [ 2.845416] spi-tegra114 7000d400.spi: Static pin configuration used [ 2.854570] spi-tegra114 7000da00.spi: Static pin configuration used [ 2.864251] tun: Universal TUN/TAP device driver, 1.6 [ 2.871179] tun: (C) 1999-2004 Max Krasnyansky [ 2.879693] PPP generic driver version 2.4.2 [ 2.886021] PPP BSD Compression module registered [ 2.892630] PPP Deflate Compression module registered [ 2.899627] PPP MPPE Compression module registered [ 2.906377] NET: Registered protocol family 24 [ 2.912863] usbcore: registered new interface driver r8152 [ 2.920412] usbcore: registered new interface driver asix [ 2.927816] usbcore: registered new interface driver ax88179_178a [ 2.935827] usbcore: registered new interface driver cdc_ether [ 2.943542] usbcore: registered new interface driver smsc95xx [ 2.951100] usbcore: registered new interface driver net1080 [ 2.958479] usbcore: registered new interface driver cdc_subset [ 2.966078] usbcore: registered new interface driver zaurus [ 2.973295] usbcore: registered new interface driver cdc_ncm [ 2.980562] usbcore: registered new interface driver cdc_acm [ 2.987651] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 2.998527] usbcore: registered new interface driver usb-storage [ 3.006116] usbcore: registered new interface driver usbserial [ 3.013426] usbcore: registered new interface driver ftdi_sio [ 3.020560] usbserial: USB Serial support registered for FTDI USB Serial Device [ 3.030622] usbcore: registered new interface driver option [ 3.037663] usbserial: USB Serial support registered for GSM modem (1-port) [ 3.046144] usbcore: registered new interface driver pl2303 [ 3.053205] usbserial: USB Serial support registered for pl2303 [ 3.061641] tegra-xudc-new 700d0000.xudc: usb2 phy is not available yet [ 3.201701] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc1 [ 3.214449] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc0 [ 3.223294] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock [ 3.231653] i2c /dev entries driver [ 3.238170] [OV5693]: probing v4l2 sensor. [ 4.107488] IR NEC protocol handler initialized [ 4.113820] IR Sharp protocol handler initialized [ 4.120348] IR XMP protocol handler initialized [ 4.126808] usbcore: registered new interface driver uvcvideo [ 4.134475] USB Video Class driver (1.1.1) [ 4.140830] max77620-power max77620-power: Event recorder REG_NVERC : 0x0 [ 4.151750] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2 [ 4.160899] tegra_soctherm 700e2000.soctherm: pllx_offset tz:1 max:8, min:4 [ 4.170391] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC [ 4.183257] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC [ 4.196523] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.210081] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC [ 4.223358] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC [ 4.236898] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000 [ 4.250677] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature 2147483647 forced to 127000 [ 4.264327] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC [ 4.277963] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature [ 4.291053] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19 [ 4.302145] tegra_aotag tegra-aotag: Registering sensor 0 [ 4.310201] tegra_aotag tegra-aotag: Bound to TZ : ID 0 [ 4.317960] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0 [ 4.326823] FAN dev name: pwm-fan [ 4.332610] FAN:gpio request success. [ 4.338783] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255 [ 4.347252] pwm_fan_driver pwm-fan: got pwm for fan [ 4.354694] pwm_fan_driver pwm-fan: fan tach request irq success [ 4.363092] pwm_fan_driver pwm-fan: tach period: 1000 [ 4.370546] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2 [ 4.382561] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2 [ 4.394742] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2 [ 4.407013] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2 [ 4.419281] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3 [ 4.431552] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3 [ 4.443821] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3 [ 4.456088] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4 [ 4.468376] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4 [ 4.480990] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4 [ 4.494844] tegra-wdt 60005100.watchdog: Tegra WDT enabled on probe. Timeout = 120 seconds. [ 4.508635] tegra-wdt 60005100.watchdog: initialized (timeout = 120 sec, nowayout = 1) [ 4.522390] device-mapper: uevent: version 1.0.3 [ 4.530073] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com [ 4.546287] sdhci: Secure Digital Host Controller Interface driver [ 4.555220] sdhci: Copyright(c) Pierre Ossman [ 4.562258] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.571237] sdhci-tegra sdhci-tegra.3: Parent select= pll_p rate=408000000 [ 4.580896] sdhci-tegra sdhci-tegra.3: Parent select= pll_c4_out2 rate=199680000 [ 4.593411] sdhci-tegra sdhci-tegra.3: Client registration for eMC Successful [ 4.606258] tegra-se 70012000.se: tegra_se_probe: complete [ 4.615076] hidraw: raw HID events driver (C) Jiri Kosina [ 4.626006] usbcore: registered new interface driver usbhid [ 4.634046] usbhid: USB HID core driver [ 4.639498] mmc0: SDHCI controller on sdhci-tegra.3 [sdhci-tegra.3] using ADMA 64-bit with 64 bit addr [ 4.639861] sdhci-tegra sdhci-tegra.1: Parent select= pll_p rate=408000000 [ 4.639880] sdhci-tegra sdhci-tegra.1: Client registration for eMC Successful [ 4.676501] parse_throttle_dt_data: Num cap clks = 6 [ 4.681946] mmc0: MAN_BKOPS_EN bit is not set [ 4.687526] mmc1: SDHCI controller on sdhci-tegra.1 [sdhci-tegra.1] using ADMA 64-bit with 64 bit addr [ 4.688268] sdhci-tegra sdhci-tegra.0: Got CD GPIO [ 4.688320] sdhci-tegra sdhci-tegra.0: Got WP GPIO [ 4.688403] sdhci-tegra sdhci-tegra.0: Parent select= pll_p rate=408000000 [ 4.688451] sdhci-tegra sdhci-tegra.0: wakeup init done, cd_irq: 262 [ 4.688473] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful [ 4.689606] mmc0: Skipping tuning since strobe enabled [ 4.690595] en-vdd-sd: supplied by vdd-3v3 [ 4.695591] mmc0: new HS400 MMC card at address 0001 [ 4.695847] mmcblk mmc0:0001: Card claimed for testing. [ 4.700477] mmcblk0: mmc0:0001 016G32 14.7 GiB [ 4.701012] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB [ 4.702824] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 [ 4.727759] mmc2: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA 64-bit with 64 bit addr [ 4.744947] mmc1: queuing unknown CIS tuple 0x80 (5 bytes) [ 4.819185] parse_throttle_dt_data: clk=cclk_g type=2 [ 4.826305] parse_throttle_dt_data: clk=gpu type=4 [ 4.833077] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0 [ 4.841103] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0 [ 4.849093] parse_throttle_dt_data: clk=cap.throttle.sclk type=0 [ 4.856881] parse_throttle_dt_data: clk=emc type=3 [ 4.864257] tegra_throttle_probe: probe successful. #cdevs=4 [ 4.871988] tegra21x_actmon 6000c800.actmon: in actmon_register()... [ 4.881099] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all [ 4.894604] tegra124-dfll 70110000.clock: config PMU interface as PWM [ 4.905051] coresight-tmc 72030000.etf: TMC initialized [ 4.913829] coresight-tmc 72050000.etr: TMC initialized [ 4.921150] coresight-tpiu 72060000.tpiu: TPIU initialized [ 4.928897] coresight-funnel 73010000.funnel_bccplex: FUNNEL initialized [ 4.937788] coresight-funnel 72010000.funnel_major: FUNNEL initialized [ 4.946801] coresight-replicator 72040000.replicator: REPLICATOR initialized [ 4.949469] mmc1 tuning done saved tap delay=46 [ 4.949471] mmc1: hw tuning done ... [ 4.949478] mmc1: tuning_window[0]: 0xe7ffffff [ 4.949484] mmc1: tuning_window[1]: 0xffffffff [ 4.949489] mmc1: tuning_window[2]: 0xfffffff8 [ 4.949495] mmc1: tuning_window[3]: 0x7fffff1f [ 4.949501] mmc1: tuning_window[4]: 0x0 [ 4.949506] mmc1: tuning_window[5]: 0x0 [ 4.949511] mmc1: tuning_window[6]: 0x0 [ 4.949517] mmc1: tuning_window[7]: 0x0 [ 4.949521] sdhci: Tap value: 46 | Trim value: 8 [ 4.949524] sdhci: SDMMC_VENDOR_INTR_STATUS[0x108]: 0x40000 [ 4.955048] mmc1: queuing unknown CIS tuple 0x91 (3 bytes) [ 4.955093] mmc1: new ultra high speed SDR104 SDIO card at address 0001 [ 5.044921] coresight-etm4x 73440000.ptm: ETM 4.0 initialized [ 5.052774] coresight-etm4x 73540000.ptm: ETM 4.0 initialized [ 5.060583] coresight-etm4x 73640000.ptm: ETM 4.0 initialized [ 5.068365] coresight-etm4x 73740000.ptm: ETM 4.0 initialized [ 5.076872] usbcore: registered new interface driver snd-usb-audio [ 5.084384] No Device Node present for smmu client: snd-soc-dummy !! [ 5.092033] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 5.106872] No Device Node present for smmu client: snd-soc-dummy !! [ 5.114744] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 5.127252] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input0 [ 5.138479] No Device Node present for smmu client: snd-soc-dummy !! [ 5.146498] snd-soc-dummy snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 5.160012] No Device Node present for smmu client: snd-soc-dummy !! [ 5.168276] snd-soc-dummy snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000) [ 5.205079] tegra210-i2s tegra210-i2s.0: Missing prop fsync-width for I2S0 [ 5.216041] tegra210-i2s tegra210-i2s.2: Missing prop fsync-width for I2S2 [ 5.225743] tegra210-i2s tegra210-i2s.3: Missing prop fsync-width for I2S3 [ 5.235517] tegra210-i2s tegra210-i2s.4: Missing prop fsync-width for I2S4 [ 5.257600] OPE platform probe [ 5.262904] OPE platform probe successful [ 5.269295] OPE platform probe [ 5.274507] OPE platform probe successful [ 5.315109] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF1 <-> ADMAIF1 mapping ok [ 5.326968] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF2 <-> ADMAIF2 mapping ok [ 5.338895] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF3 <-> ADMAIF3 mapping ok [ 5.350843] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF4 <-> ADMAIF4 mapping ok [ 5.362814] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF5 <-> ADMAIF5 mapping ok [ 5.374783] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF6 <-> ADMAIF6 mapping ok [ 5.386798] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF7 <-> ADMAIF7 mapping ok [ 5.398835] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF8 <-> ADMAIF8 mapping ok [ 5.410916] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF9 <-> ADMAIF9 mapping ok [ 5.423091] tegra-snd-t210ref-mobile-rt565x sound: ADMAIF10 <-> ADMAIF10 mapping ok [ 5.459560] input: tegra-snd-t210ref-mobile-rt565x Headphone Jack as /devices/sound/sound/card1/input1 [ 5.475100] tegra-snd-t210ref-mobile-rt565x sound: codec-dai "dit-hifi" registered [ 5.488148] tegra-snd-t210ref-mobile-rt565x sound: This is a dummy codec [ 5.498541] GACT probability NOT on [ 5.504812] Mirror/redirect action on [ 5.511208] u32 classifier [ 5.516540] Actions configured [ 5.522525] Netfilter messages via NETLINK v0.30. [ 5.529831] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 5.538868] ctnetlink v0.93: registering with nfnetlink. [ 5.547399] xt_time: kernel timezone is -0000 [ 5.554220] IPVS: Registered protocols () [ 5.560627] IPVS: Connection hash table configured (size=4096, memory=64Kbytes) [ 5.572703] IPVS: Creating netns size=1424 id=0 [ 5.579590] IPVS: ipvs loaded. [ 5.584889] IPVS: [rr] scheduler registered. [ 5.591497] ipip: IPv4 over IPv4 tunneling driver [ 5.598938] ip_tables: (C) 2000-2006 Netfilter Core Team [ 5.606526] arp_tables: (C) 2002 David S. Miller [ 5.613274] Initializing XFRM netlink socket [ 5.620237] NET: Registered protocol family 10 [ 5.627673] mip6: Mobile IPv6 [ 5.632553] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 5.639992] sit: IPv6 over IPv4 tunneling driver [ 5.647536] NET: Registered protocol family 17 [ 5.653771] NET: Registered protocol family 15 [ 5.659916] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 5.675988] Key type dns_resolver registered [ 5.682760] Registered cp15_barrier emulation handler [ 5.697283] isp 54600000.isp: initialized [ 5.704437] isp 54680000.isp: initialized [ 5.718244] clk_cbus_recalc_rate: no gbus parent [ 5.724590] clk_cbus_round_rate: no gbus parent [ 5.730791] clk_cbus_round_rate: no gbus parent [ 5.736949] clk_cbus_recalc_rate: no gbus parent [ 5.743716] clk_cbus_recalc_rate: no gbus parent [ 5.749867] clk_cbus_round_rate: no gbus parent [ 5.755872] clk_cbus_round_rate: no gbus parent [ 5.761836] clk_cbus_recalc_rate: no gbus parent [ 5.767906] tegra_dvfs: GPU-cap: registered [ 5.773605] tegra dvfs: vdd-cpu: nominal 1226mV, offset 708000uV, step 19200uV, scaling enabled [ 5.785212] tegra dvfs: vdd-core: nominal 1125mV, offset 600000uV, step 12500uV, scaling enabled [ 5.797087] tegra dvfs: vdd-gpu: nominal 1120mV, offset 710000uV, step 10000uV, scaling enabled [ 5.812159] tegra_dvfs: vdd-gpu-vts: registered [ 5.820247] xhci-tegra 70090000.xusb: can't get usb3-0 phy (-517) [ 5.828836] tegra21x-padctl-uphy 7009f000.pinctrl: padctl mmio start 0x000000007009f000 end 0x000000007009ffff [ 5.842408] tegra21x-padctl-uphy 7009f000.pinctrl: TEGRA_FUSE_SKU_CALIB_0 0x9a6a414 [ 5.853633] tegra21x-padctl-uphy 7009f000.pinctrl: TEGRA_FUSE_USB_CALIB_EXT_0 0x4 [ 5.866194] tegra21x-padctl-uphy 7009f000.pinctrl: UTMI-0 is used by XUSB [ 5.875040] tegra21x-padctl-uphy 7009f000.pinctrl: using UTMI port 0 for otg [ 5.884165] tegra21x-padctl-uphy 7009f000.pinctrl: UTMI-2 is used by XUSB [ 5.892990] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 5, set usb3_lanes = 0x20 [ 5.905073] tegra21x-padctl-uphy 7009f000.pinctrl: USB3 port 1 maps to USB2 port 2 [ 5.917040] tegra21x-padctl-uphy 7009f000.pinctrl: UTMI-1 is used by XUSB [ 5.926222] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 6, set usb3_lanes = 0x60 [ 5.938944] tegra21x-padctl-uphy 7009f000.pinctrl: USB3 port 0 maps to USB2 port 1 [ 5.951339] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 1, set pcie_lanes = 0x2 [ 5.964093] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 2, set pcie_lanes = 0x6 [ 5.976847] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 3, set pcie_lanes = 0xe [ 5.989710] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 4, set pcie_lanes = 0x1e [ 6.002710] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 0, set pcie_lanes = 0x1f [ 6.015709] tegra21x-padctl-uphy 7009f000.pinctrl: uphy_lane = 7, set sata_lanes = 0x80 [ 6.029397] usb-vbus1: supplied by vdd-3v3 [ 6.038384] tegra21x-padctl-uphy 7009f000.pinctrl: Done tegra21x_padctl_uphy_probe [ 6.053862] tegra-pcie 1003000.pcie-controller: 4x1, 1x1 configuration [ 6.063340] tegra-pcie 1003000.pcie-controller: PCIE: Enable power rails [ 6.073144] clk_cbus_round_rate: no gbus parent [ 6.080269] tegra_gpu_edp gpu_edp: unable to get max GPU freq [ 6.089192] tegra-ahci 70027000.sata: Missing devslp-active state [ 6.089741] tegra-pcie 1003000.pcie-controller: probing port 0, using 4 lanes [ 6.090934] gk20a 57000000.gpu: GPCPLL initial settings: NA mode, M=1, N=34, P=3 [ 6.091581] tegra-pcie 1003000.pcie-controller: probing port 1, using 1 lanes [ 6.092925] gk20a 57000000.gpu: failed to allocate secure buffer -12 [ 6.139497] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode [ 6.153530] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pmp pio slum part deso sadm apst [ 6.173064] scsi host0: tegra_ahci [ 6.179712] scsi host1: tegra_ahci [ 6.185674] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 370 [ 6.198293] ata2: DUMMY [ 6.206323] tegra-xudc-new 700d0000.xudc: USB charger detection disabled [ 6.215412] tegra-xudc-new 700d0000.xudc: device mode on [ 6.224808] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered [ 6.239727] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered [ 6.253439] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered [ 6.266873] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered [ 6.281780] tegra124-dfll 70110000.clock: entered closed loop mode [ 6.292811] xhci-tegra 70090000.xusb: UTMI port 0 has OTG_CAP [ 6.299511] xhci-tegra 70090000.xusb: No USB3 port has OTG_CAP [ 6.309673] xhci-tegra 70090000.xusb: Direct firmware load for tegra21x_xusb_firmware failed with error -2 [ 6.321058] xhci-tegra 70090000.xusb: Falling back to user helper [ 6.323489] input: gpio-keys as /devices/gpio-keys/input/input2 [ 6.346566] tegra_rtc 7000e000.rtc: setting system clock to 2000-01-01 01:13:19 UTC (946689199) [ 6.358137] vi 54080000.vi: vi_probe: ++ [ 6.373612] vi 54080000.vi: initialized [ 6.384162] vi 54080000.vi: subdev nvcsi-2 bound [ 6.389670] vi 54080000.vi: subdev ov5693 6-0036 bound [ 6.396856] Disable partitions left on by BL [ 6.402001] disb [ 6.416800] DRAM derating cdev registered. [ 6.422537] vdd-cpu-fixed: disabling [ 6.426963] vdd-cam-hv: disabling [ 6.431153] avdd-ts-hv: disabling [ 6.435297] vdd-ts: disabling [ 6.439057] max77620-gpio7: disabling [ 6.443738] lcd-bl-en: disabling [ 6.447581] en-vdd-sd: disabling [ 6.451443] en-vdd-cam: disabling [ 6.455364] aux-3v3: disabling [ 6.459001] snsr_pm: disabling [ 6.462609] vdd-disp-3v0: disabling [ 6.466654] vdd-fan: disabling [ 6.470250] usb-vbus1: disabling [ 6.473990] en-vdd-ts-1v8: disabling [ 6.478060] en-vdd-ts-hv-3v3: disabling [ 6.482371] en-vdd-disp-3v3: disabling [ 6.486827] en-mdm-pwr-3v7: disabling [ 6.490870] en-vdd-disp-1v8: disabling [ 6.495284] en-vdd-cam-hv-2v8: disabling [ 6.499586] rtl-5v0: disabling [ 6.503054] en-usb-vbus2: disabling [ 6.506966] en-vdd-cam-1v2: disabling [ 6.511041] en-vdd-vcm-2v8: disabling [ 6.515101] en-vdd-cam-1v2-alt: disabling [ 6.520905] ALSA device list: [ 6.523526] ata1: SATA link down (SStatus 0 SControl 300) [ 6.530054] #0: tegra-hda at 0x70038000 irq 348 [ 6.535189] #1: tegra-snd-t210ref-mobile-rt565x [ 6.541645] EXT4-fs (mmcblk0p1): couldn't mount as ext3 due to feature incompatibilities [ 6.551688] EXT4-fs (mmcblk0p1): couldn't mount as ext2 due to feature incompatibilities [ 6.566009] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) [ 6.575286] VFS: Mounted root (ext4 filesystem) on device 179:1. [ 6.584298] devtmpfs: mounted [ 6.588207] Freeing unused kernel memory: 1208K (ffffffc001168000 - ffffffc001296000) [ 6.597406] Freeing alternatives memory: 76K (ffffffc001296000 - ffffffc0012a9000) [ 6.614256] btb inv war enabled [ 6.629724] tegra-pcie 1003000.pcie-controller: link 0 down, retrying [ 6.672861] systemd[1]: System time before build time, advancing clock. [ 6.697552] random: systemd: uninitialized urandom read (16 bytes read, 76 bits of entropy available) [ 6.709804] random: systemd: uninitialized urandom read (16 bytes read, 77 bits of entropy available) [ 6.720884] random: systemd: uninitialized urandom read (16 bytes read, 77 bits of entropy available) [ 6.737190] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN) [ 6.758574] systemd[1]: Detected architecture arm64. [ 6.773437] systemd[1]: Set hostname to . [ 6.788951] random: systemd: uninitialized urandom read (16 bytes read, 78 bits of entropy available) [ 6.801124] random: systemd: uninitialized urandom read (16 bytes read, 78 bits of entropy available) [ 6.816626] random: systemd-sysv-ge: uninitialized urandom read (16 bytes read, 78 bits of entropy available) [ 6.818031] random: systemd-cryptse: uninitialized urandom read (16 bytes read, 78 bits of entropy available) [ 6.820238] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 78 bits of entropy available) [ 6.820313] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 78 bits of entropy available) [ 6.820332] random: systemd-gpt-aut: uninitialized urandom read (16 bytes read, 78 bits of entropy available) [ 6.989167] systemd[1]: Listening on Journal Audit Socket. [ 6.996888] systemd[1]: Reached target Encrypted Volumes. [ 7.004454] systemd[1]: Listening on udev Kernel Socket. [ 7.012572] systemd[1]: Created slice User and Session Slice. [ 7.020479] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ 7.029671] systemd[1]: Listening on Syslog Socket. [ 7.036699] systemd[1]: Reached target User and Group Name Lookups. [ 7.039499] tegra-pcie 1003000.pcie-controller: link 0 down, retrying [ 7.056535] systemd[1]: Listening on LVM2 poll daemon socket. [ 7.064415] systemd[1]: Listening on Device-mapper event daemon FIFOs. [ 7.073059] systemd[1]: Listening on udev Control Socket. [ 7.080530] systemd[1]: Listening on Journal Socket (/dev/log). [ 7.088519] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 7.099016] systemd[1]: Reached target Remote File Systems (Pre). [ 7.107133] systemd[1]: Reached target Remote File Systems. [ 7.115365] systemd[1]: Created slice System Slice. [ 7.122284] systemd[1]: Reached target Slices. [ 7.129301] systemd[1]: Created slice system-getty.slice. [ 7.136706] systemd[1]: Listening on LVM2 metadata daemon socket. [ 7.144772] systemd[1]: Reached target Swap. [ 7.154953] systemd[1]: Listening on Journal Socket. [ 7.163153] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling... [ 7.177746] systemd[1]: Starting Remount Root and Kernel File Systems... [ 7.185462] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null) [ 7.194395] systemd[1]: Mounting POSIX Message Queue File System... [ 7.204101] systemd[1]: Mounting Debug File System... [ 7.215684] systemd[1]: Starting Create list of required static device nodes for the current kernel... [ 7.229367] systemd[1]: Starting Journal Service... [ 7.238266] systemd[1]: Started Braille Device Support. [ 7.249859] systemd[1]: Starting Load Kernel Modules... [ 7.262038] systemd[1]: Created slice system-serial\x2dgetty.slice. [ 7.273506] systemd[1]: Mounted POSIX Message Queue File System. [ 7.281760] systemd[1]: Mounted Debug File System. [ 7.289951] systemd[1]: Started Remount Root and Kernel File Systems. [ 7.300168] systemd[1]: Started Create list of required static device nodes for the current kernel. [ 7.315084] systemd[1]: Started Load Kernel Modules. [ 7.322685] systemd[1]: Started Journal Service. [ 7.443081] tegra-pcie 1003000.pcie-controller: link 0 down, retrying [ 7.452575] tegra-pcie 1003000.pcie-controller: link 0 down, ignoring [ 7.482660] systemd-journald[226]: Received request to flush runtime journal from PID 1 [ 7.704027] xhci-tegra 70090000.xusb: cannot find firmware....retry after 1 second [ 7.802211] random: nonblocking pool is initialized [ 7.869816] tegra-pcie 1003000.pcie-controller: link 1 down, retrying [ 7.909222] dhd_module_init in [ 7.913180] found wifi platform device bcmdhd_wlan [ 7.921305] Power-up adapter 'DHD generic adapter' [ 7.927981] wifi_platform_set_power = 1 [ 8.140757] wifi_platform_bus_enumerate device present 1 [ 8.164656] wifi_platform_bus_enumerate device present 0 [ 8.165106] F1 signature read @0x18000000=0x17214354 [ 8.169519] F1 signature OK, socitype:0x1 chip:0x4354 rev:0x1 pkg:0x2 [ 8.170085] DHD: dongle ram size is set to 786432(orig 786432) at 0x180000 [ 8.170150] wifi_platform_prealloc: failed to alloc static mem section 7 [ 8.170156] wifi_platform_get_mac_addr [ 8.188342] CFG80211-ERROR) wl_setup_wiphy : Registering Vendor80211 [ 8.188592] wl_create_event_handler(): thread:wl_event_handler:1c4 started [ 8.188672] CFG80211-ERROR) wl_event_handler : tsk Enter, tsk = 0xffffffc0f1361a70 [ 8.188693] dhd_attach(): thread:dhd_watchdog_thread:1c5 started [ 8.188722] dhd_attach(): thread:dhd_dpc:1c6 started [ 8.188756] dhd_attach(): thread:dhd_rxf:1c7 started [ 8.188761] dhd_deferred_work_init: work queue initialized [ 8.188990] Dongle Host Driver, version 1.201.82 (r) [ 8.188990] Compiled in drivers/net/wireless/bcmdhd on Mar 1 2018 at 20:43:08 [ 8.189294] tegra_sysfs_register [ 8.189326] Register interface [wlan0] MAC: 00:04:4b:5a:e6:6c [ 8.189326] [ 8.189329] dhd_prot_ioctl : bus is down. we have nothing to do [ 8.189421] sdhci-tegra sdhci-tegra.1: Tuning already done, restoring the best tap value : 46 [ 8.190464] wifi_platform_set_power = 0 [ 8.291476] tegra-pcie 1003000.pcie-controller: link 1 down, retrying [ 8.506775] using random self ethernet address [ 8.512042] using random host ethernet address [ 8.534060] Mass Storage Function, version: 2009/09/11 [ 8.534066] LUN: removable file: (no medium) [ 8.542887] using random self ethernet address [ 8.542890] using random host ethernet address [ 8.546783] usb0: HOST MAC 3a:3d:75:5a:8a:69 [ 8.547579] usb0: MAC 62:be:c3:39:30:f5 [ 8.547931] usb1: HOST MAC 96:ca:7c:db:08:44 [ 8.547947] usb1: MAC e6:6d:1f:a6:7c:03 [ 8.547970] tegra-xudc-new 700d0000.xudc: ep 0 (type: 0, dir: out) enabled [ 8.695627] tegra-pcie 1003000.pcie-controller: link 1 down, retrying [ 8.697642] tegra-pcie 1003000.pcie-controller: link 1 down, ignoring [ 8.697662] tegra-pcie 1003000.pcie-controller: PCIE: no end points detected [ 8.698712] tegra-pcie 1003000.pcie-controller: PCIE: Disable power rails [ 8.786077] device usb0 entered promiscuous mode [ 8.794282] xhci-tegra 70090000.xusb: Firmware timestamp: 2017-10-20 11:40:00 UTC, Version: 50.19 release [ 8.808456] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready [ 8.809527] xhci-tegra 70090000.xusb: xHCI Host Controller [ 8.809544] xhci-tegra 70090000.xusb: new USB bus registered, assigned bus number 1 [ 8.810404] xhci-tegra 70090000.xusb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010810 [ 8.810430] xhci-tegra 70090000.xusb: irq 319, io mem 0x70090000 [ 8.810555] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 8.810557] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.810560] usb usb1: Product: xHCI Host Controller [ 8.810562] usb usb1: Manufacturer: Linux 4.4.38-tegra xhci-hcd [ 8.810564] usb usb1: SerialNumber: 70090000.xusb [ 8.810893] hub 1-0:1.0: USB hub found [ 8.810920] hub 1-0:1.0: 5 ports detected [ 8.815152] device usb1 entered promiscuous mode [ 8.828121] IPv6: ADDRCONF(NETDEV_UP): usb1: link is not ready [ 8.828126] l4tbr0: port 2(usb1) entered forwarding state [ 8.828137] l4tbr0: port 2(usb1) entered forwarding state [ 8.835535] xhci-tegra 70090000.xusb: xHCI Host Controller [ 8.835542] xhci-tegra 70090000.xusb: new USB bus registered, assigned bus number 2 [ 8.835732] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 8.835734] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.835737] usb usb2: Product: xHCI Host Controller [ 8.835739] usb usb2: Manufacturer: Linux 4.4.38-tegra xhci-hcd [ 8.835741] usb usb2: SerialNumber: 70090000.xusb [ 8.836072] hub 2-0:1.0: USB hub found [ 8.836094] hub 2-0:1.0: 4 ports detected [ 8.839553] android_work: did not send uevent (0 0 (null)) [ 8.850634] android_work: did not send uevent (0 0 (null)) [ 8.919306] android_work: sent uevent USB_STATE=CONNECTED [ 8.922646] android_work: sent uevent USB_STATE=DISCONNECTED [ 8.930639] android_work: did not send uevent (0 0 (null)) [ 9.027288] android_work: sent uevent USB_STATE=CONNECTED [ 9.035124] configfs-gadget gadget: high-speed config #1: c [ 9.041536] tegra-xudc-new 700d0000.xudc: ep 5 (type: 3, dir: in) enabled [ 9.049144] tegra-xudc-new 700d0000.xudc: ep 3 (type: 2, dir: in) enabled [ 9.049159] tegra-xudc-new 700d0000.xudc: ep 2 (type: 2, dir: out) enabled [ 9.049278] tegra-xudc-new 700d0000.xudc: ep 9 (type: 3, dir: in) enabled [ 9.049294] tegra-xudc-new 700d0000.xudc: ep 7 (type: 2, dir: in) enabled [ 9.049309] tegra-xudc-new 700d0000.xudc: ep 4 (type: 2, dir: out) enabled [ 9.049337] tegra-xudc-new 700d0000.xudc: ep 15 (type: 3, dir: in) enabled [ 9.049510] IPv6: ADDRCONF(NETDEV_CHANGE): usb0: link becomes ready [ 9.049629] l4tbr0: port 1(usb0) entered forwarding state [ 9.049646] l4tbr0: port 1(usb0) entered forwarding state [ 9.049699] android_work: sent uevent USB_STATE=CONFIGURED [ 9.049758] tegra-xudc-new 700d0000.xudc: ep 11 (type: 2, dir: in) enabled [ 9.049773] tegra-xudc-new 700d0000.xudc: ep 6 (type: 2, dir: out) enabled [ 9.056707] tegra-xudc-new 700d0000.xudc: ep 13 (type: 2, dir: in) enabled [ 9.056724] tegra-xudc-new 700d0000.xudc: ep 8 (type: 2, dir: out) enabled [ 9.056820] IPv6: ADDRCONF(NETDEV_CHANGE): usb1: link becomes ready [ 9.160024] usb 2-1: new SuperSpeed USB device number 2 using xhci-tegra [ 9.177018] usb 2-1: New USB device found, idVendor=0955, idProduct=09ff [ 9.184478] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6 [ 9.195686] usb 2-1: Product: USB 10/100/1000 LAN [ 9.201170] usb 2-1: Manufacturer: Nvidia [ 9.206565] usb 2-1: SerialNumber: 000001000000 [ 9.213434] xhci-tegra 70090000.xusb: tegra_xhci_mbox_work mailbox command 6 [ 9.223189] xhci-tegra 70090000.xusb: tegra_xhci_mbox_work mailbox command 6 [ 9.231632] xhci-tegra 70090000.xusb: tegra_xhci_mbox_work mailbox command 6 [ 9.352353] usb 2-1: reset SuperSpeed USB device number 2 using xhci-tegra [ 9.374227] r8152 2-1:1.0 eth0: v2.09.00 (2017/08/21) [ 9.380213] r8152 2-1:1.0 eth0: This product is covered by one or more of the following patents: [ 9.380213] ..US6,570,884, US6,115,776, and US6,327,625. [ 9.380213] [ 9.652547] IPVS: Creating netns size=1424 id=1 [ 10.038063] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 10.044867] [ 10.044867] Dongle Host Driver, version 1.201.82 (r) [ 10.044867] Compiled in drivers/net/wireless/bcmdhd on Mar 1 2018 at 20:43:08 [ 10.062762] wl_android_wifi_on in [ 10.066853] wifi_platform_set_power = 1 [ 10.110277] tegradc tegradc.1: blank - normal [ 10.352588] mmc1: queuing unknown CIS tuple 0x80 (5 bytes) [ 10.438452] sdhci-tegra sdhci-tegra.1: Tuning already done, restoring the best tap value : 46 [ 10.447678] F1 signature read @0x18000000=0x17214354 [ 10.456535] F1 signature OK, socitype:0x1 chip:0x4354 rev:0x1 pkg:0x2 [ 10.463623] DHD: dongle ram size is set to 786432(orig 786432) at 0x180000 [ 10.608128] tegradc tegradc.1: unblank [ 10.649073] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded. [ 10.698339] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us) [ 10.705514] wifi_platform_get_mac_addr [ 10.711301] Firmware up: op_mode=0x0005, MAC=00:04:4b:5a:e6:6c [ 10.724153] dhd_preinit_ioctls pspretend_threshold for HostAPD failed -23 [ 10.736206] Firmware version = wl0: Dec 12 2017 15:09:35 version 7.35.221.34 (r679642) FWID 01-8f1f4763 [ 10.748543] dhd_interworking_enable: failed to set WNM info, ret=-23 [ 10.755358] tegra_sysfs_on [ 10.809161] cfg80211: World regulatory domain updated: [ 10.814946] cfg80211: DFS Master region: unset [ 10.819686] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 10.829501] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 10.841466] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 10.841473] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 10.841475] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 10.841478] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 10.841480] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 10.841482] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 10.841484] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 10.897090] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 10.903610] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 11.199035] CFGP2P-ERROR) wl_cfgp2p_add_p2p_disc_if : P2P interface registered [ 11.216539] WLC_E_IF: NO_IF set, event Ignored [ 11.743073] Bridge firewalling registered [ 12.023773] r8152 2-1:1.0 eth0: carrier on [ 12.027941] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 12.599399] IPv6: ADDRCONF(NETDEV_UP): docker0: link is not ready [ 12.923065] tegradc tegradc.1: unblank [ 13.865287] tegradc tegradc.1: blank - powerdown Ubuntu 16.04 LTS tegra-ubuntu ttyS0 tegra-ubuntu login: nvidia (automatic login) Welcome to Ubuntu 16.04 LTS (GNU/Linux 4.4.38-tegra aarch64) * Documentation: https://help.ubuntu.com/ 618 packages can be updated. 301 updates are security updates. The programs included with the Ubuntu system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Ubuntu comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. To run a command as administrator (user "root"), use "sudo ". See "man sudo_root" for details. nvidia@tegra-ubuntu:~$ [ 18.842220] IPVS: Creating netns size=1424 id=2 [ 19.242646] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 19.368414] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 19.404080] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 19.446908] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 19.455713] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 19.465550] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 19.500141] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 19.509197] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 19.529732] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 19.602044] Setting pll_a = 45158400 Hz clk_out = 11289600 Hz [ 19.774451] IPVS: Creating netns size=1424 id=3 [ 23.843614] l4tbr0: port 2(usb1) entered forwarding state [ 24.099493] l4tbr0: port 1(usb0) entered forwarding state nvidia@tegra-ubuntu:~$ nvidia@tegra-ubuntu:~$