assume you mean “blacklist” and that “blocklist” is a typo
In light of the proposal from some kernel developers to use more inclusive language. I’m trying to be as accurate as possible in anticipation of future changes. I assume it’ll become an alias at some point.
So something odd just happened. I was trying to get you a serial boot log. I booted it up once, and got this:
[0000.177] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 0 from HW fuses.
[0000.186] I> MB1 (prd-version: 1.5.1.3-t194-41334769-d2a21c57)
[0000.191] I> Boot-mode: Coldboot
[0000.194] I> Chip revision : A02
[0000.197] I> Bootrom patch version : 7 (correctly patched)
[0000.202] I> ATE fuse revision : 0x200
[0000.206] I> Ram repair fuse : 0x0
[0000.209] I> Ram Code : 0x0
[0000.211] I> rst_source : 0x0
[0000.214] I> rst_level : 0x0
[0000.217] I> Boot-device: eMMC
[0000.232] I> sdmmc DDR50 mode
[0000.237] I> Active Boot chain : 1
[0000.240] I> Boot-device: eMMC
[0000.243] W> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT.
[0000.251] I> Temperature = 22000
[0000.254] W> Skipping boost for clk: BPMP_CPU_NIC
[0000.259] W> Skipping boost for clk: BPMP_APB
[0000.263] W> Skipping boost for clk: AXI_CBB
[0000.267] W> Skipping boost for clk: AON_CPU_NIC
[0000.271] W> Skipping boost for clk: CAN1
[0000.275] W> Skipping boost for clk: CAN2
[0000.279] I> Boot-device: eMMC
[0000.282] I> Boot-device: eMMC
[0000.291] I> Sdmmc: HS400 mode enabled
[0000.296] I> ECC region[0]: Start:0x0, End:0x0
[0000.300] I> ECC region[1]: Start:0x0, End:0x0
[0000.304] I> ECC region[2]: Start:0x0, End:0x0
[0000.308] I> ECC region[3]: Start:0x0, End:0x0
[0000.312] I> ECC region[4]: Start:0x0, End:0x0
[0000.316] I> Non-ECC region[0]: Start:0x80000000, End:0x100000000
[0000.322] I> Non-ECC region[1]: Start:0x0, End:0x0
[0000.326] I> Non-ECC region[2]: Start:0x0, End:0x0
[0000.331] I> Non-ECC region[3]: Start:0x0, End:0x0
[0000.335] I> Non-ECC region[4]: Start:0x0, End:0x0
[0000.341] E> FAILED: Thermal config
[0000.348] E> FAILED: MEMIO rail config
[0000.361] I> Boot-device: eMMC
[0000.371] I> sdmmc bdev is already initialized
[0000.442] I> MB1 done
����main enter
SPE VERSION #: R01.00.14 Created: Sep 19 2018 @ 11:03:21
HW Function test
Start Scheduler.
in late init
��
[0000.450] I> Welcome to MB2(TBoot-BPMP) (version: 00.00.2018.32-mobile-2dfe4beb)
[0000.451] I> DMA Heap @ [0x526fa000 - 0x52ffa000]
[0000.452] I> Default Heap @ [0xd486400 - 0xd48a400]
[0000.452] E> DEVICE_PROD: Invalid value data = 70020000, size = 0.
[0000.458] W> device prod register failed
[0000.462] I> Boot-device: eMMC
[0000.465] I> Boot_device: SDMMC_BOOT instance: 3
[0000.471] I> sdmmc-3 params source = boot args
[0000.474] I> sdmmc bdev is already initialized
[0000.478] I> sdmmc-3 params source = boot args
[0000.484] I> Found 17 partitions in SDMMC_BOOT (instance 3)
[0000.492] I> Found 42 partitions in SDMMC_USER (instance 3)
[0000.494] I> Active Boot chain : 1
[0000.497] I> parsing oem signed section of bpmp-fw header done
[0000.502] I> bpmp-fw binary init read from storage
[0000.507] I> oem authentication of bpmp-fw header done
[0000.514] I> bpmp-fw binary done read from storage
[0000.516] I> bpmp-fw: Authentication init Done
[0000.521] I> parsing oem signed section of cpubl header done
[0000.526] I> cpubl binary init read from storage
[0000.531] I> bpmp-fw: Authentication Finalize Done
[0000.536] I> oem authentication of cpubl header done
[0000.540] I> cpubl binary done read from storage
[0000.545] I> cpubl: Authentication init Done
[0000.550] I> parsing oem signed section of rce header done
[0000.554] I> rce binary init read from storage
[0000.559] I> Relocating BR-BCT
[0000.561] I> cpubl: Authentication Finalize Done
[0000.566] I> oem authentication of rce header done
[0000.570] I> rce binary done read from storage
[0000.575] I> rce: Authentication init Done
[0000.579] I> parsing oem signed section of ape header done
[0000.584] I> ape binary init read from storage
[0000.588] I> rce: Authentication Finalize Done
[0000.593] I> oem authentication of ape header done
[0000.597] I> ape binary done read from storage
[0000.601] I> ape: Authentication init Done
[0000.606] I> parsing oem signed section of tos header done
[0000.611] I> tos binary init read from storage
[0000.615] I> ape: Authentication Finalize Done
[0000.620] I> oem authentication of tos header done
[0000.624] I> tos binary done read from storage
[0000.628] I> tos: Authentication init Done
[0000.632] I> parsing oem signed section of bpmp-fw-dtb header done
[0000.638] I> bpmp-fw-dtb binary init read from storage
[0000.643] I> tos: Authentication Finalize Done
[0000.649] I> oem authentication of bpmp-fw-dtb header done
[0000.656] I> bpmp-fw-dtb binary done read from storage
[0000.658] I> bpmp-fw-dtb: Authentication init Done
[0000.663] I> parsing oem signed section of cpubl-dtb header done
[0000.668] I> cpubl-dtb binary init read from storage
[0000.673] I> bpmp-fw-dtb: Authentication Finalize Done
[0000.710] I> oem authentication of cpubl-dtb header done
[0000.711] I> cpubl-dtb binary done read from storage
[0000.712] I> cpubl-dtb: Authentication init Done
[0000.714] I> parsing oem signed section of eks header done
[0000.714] I> eks binary init read from storage
[0000.715] I> cpubl-dtb: Authentication Finalize Done
[0000.715] I> oem authentication of eks header done
[0000.719] I> eks binary done read from storage
[0000.723] I> eks: Authentication init Done
[0000.727] I> eks: Authentication Finalize Done
[0000.731] I> EKB detected (length: 0x410) @ VA:0x5270a400
��NOTICE: BL31: v1.3(release):41d46a9cf
NOTICE: BL31: Built : 21:14:52, Jun 25 2020
ipc-unittest-main: 1519: Welcome to IPC unittest!!!
ipc-unittest-main: 1531: waiting forever
ipc-unittest-srv: 329: Init unittest services!!!
hwkey-agent: 40: hwkey-agent is running!!
hwkey-agent: 182: key_mgnt_processing .......
hwkey-agent: 153: ekb_verification: EKB_CMAC verification is not match.
hwkey-agent: 219: key_mgnt_processing: failed (-7)
hwkey-agent: 44: main: Failed to verify or extract EKB (-7).
exit called, thread 0xffffffffea89bd58, name trusty_app_2_92b92883-f96a-4177
platform_bootstrap_epilog: trusty bootstrap complete
��
welcome to lk
calling constructors
initializing heap
creating bootstrap completion thread
top of bootstrap2()
initializing platform
bpmp: platform_init
tag is 57f8a77779f848bf2ecf21dabee5645f
tag_show initialized
dt initialized
mail initialized
chipid initialized
fuse initialized
sku initialized
speedo initialized
ec_get_ec_list: found 45 ecs
ec initialized
ec_mrq initialized
vmon_populate_monitors: found 3 monitors
vmon initialized
adc initialized
fmon_populate_monitors: found 73 monitors
fmon initialized
fmon_mrq initialized
reset initialized
nvhs initialized
392 clocks registered
WARNING: pll_c4 has no dyn ramp
clk_mrq_init: mrq handler registered
clk initialized
nvlink initialized
io_dpd initialized
io_dpd initialized
thermal initialized
i2c5 controller initialized
initialized i2c mrq handling
i2c initialized
regulator initialized
avfs_clk_platform initialized
soctherm initialized
aotag initialized
powergate initialized
dvs initialized
pm initialized
pg_late initialized
strap initialized
tag initialized
emc initialized
clk_dt initialized
avfs_ccplex_platform initialized
tj_max: dt node not found
tj_init initialized
uphy_mrq_init: mrq handler registered
uphy_dt initialized
uphy initialized
safereg_init: period 80 ms
ec_late initialized
��
��mrq initialized
��[0001.200] I> Welcome to Cboot
��fmon_post initialized
��[0001.200] I> Cboot Version: t194-18fdfe28
[0001.200] I> CPU-BL Params @ 0xf2820000
[0001.201] I> 0) Base:0x00000000 Size:0x00000000
[0001.205] I> 1) Base:0xf1100000 Size:0x00100000
[0001.209] I> 2) Base:0xf2000000 Size:0x00200000
��clk_set_parent failed for clk can1, parent pll_aon (-22)
clk_set_parent failed for clk can2, parent pll_aon (-22)
clk_set_parent failed for clk dmic5, parent pll_aon (-22)
clk_set_parent failed for clk i2c2, parent pll_aon (-22)
clk_set_parent failed for clk i2c8, parent pll_aon (-22)
clk_set_parent failed for clk spi2, parent pll_aon (-22)
clk_set_parent failed for clk pwm4, parent pll_aon (-22)
clk_dt_late initialized
machine_check initialized
pm_post initialized
dbells initialized
avfs_clk_platform_post initialized
dmce initialized
cvc initialized
ccplex_avfs_hw_init: nafll_cluster0: not monitored
ccplex_avfs_hw_init: nafll_cluster1: not monitored
ccplex_avfs_hw_init: nafll_cluster2: not monitored
ccplex_avfs_hw_init: nafll_cluster3: not monitored
avfs_clk_mach_post initialized
regulator_post initialized
rm initialized
sc7_diag initialized
thermal_test initialized
serial_late initialized
clk_post initialized
clk_dt_post initialized
mc_reg initialized
pg_post initialized
dyn_modules initialized
sku_debugfs initialized
speedo_debugfs initialized
adc_debugfs initialized
clk_debugfs initialized
��[0001.213] I> 3) Base:0xf1200000 Size:0x00200000
[0001.318] I> 4) Base:0xf1000000 Size:0x00100000
[0001.323] I> 5) Base:0xf0f00000 Size:0x00100000
[0001.327] I> 6) Base:0xf3800000 Size:0x00400000
[0001.332] I> 7) Base:0xf1c00000 Size:0x00400000
[0001.336] I> 8) Base:0xf0e00000 Size:0x00100000
[0001.341] I> 9) Base:0xf0d00000 Size:0x00100000
[0001.345] I> 10) Base:0xf3000000 Size:0x00800000
[0001.350] I> 11) Base:0x40000000 Size:0x00040000
��emc_debugfs initialized
dvs_debugfs initialized
��[0001.354] I> 12) Base:0xf0c00000 Size:0x00100000
��fmon_debugfs initialized
vmon_debugfs initialized
pg_debugfs initialized
profile_fs initialized
debugfs_cons initialized
mail_fs initialized
profile initialized
cvc_debugfs initialized
dmce_debugfs initialized
ec_debugfs initialized
rm_debugfs initialized
soctherm_debug initialized
gr_reader initialized
mods initialized
dt_fs initialized
debugfs_mrq initialized
debug_mrq initialized
debug_safereg initialized
initializing target
calling apps_init()
starting app shell
entering main console loop
] ��[0001.363] I> 13) Base:0x40046000 Size:0x00002000
[0001.414] I> 14) Base:0x40048000 Size:0x00002000
[0001.418] I> 15) Base:0xac000000 Size:0x00004000
[0001.423] I> 16) Base:0x4004a000 Size:0x00002000
[0001.427] I> 17) Base:0xf0b00000 Size:0x00100000
[0001.432] I> 18) Base:0x4004c000 Size:0x00002000
[0001.436] I> 19) Base:0xf2200000 Size:0x00600000
[0001.441] I> 20) Base:0x4004e000 Size:0x00002000
[0001.445] I> 21) Base:0xf09d0000 Size:0x0000c000
[0001.449] I> 22) Base:0x00000000 Size:0x00000000
[0001.454] I> 23) Base:0xf09e0000 Size:0x00020000
[0001.458] I> 24) Base:0xf6000000 Size:0x02000000
[0001.463] I> 25) Base:0x40050000 Size:0x00002000
[0001.467] I> 26) Base:0x40040000 Size:0x00006000
[0001.472] I> 27) Base:0xf1800000 Size:0x00400000
[0001.476] I> 28) Base:0xf4c00000 Size:0x01400000
[0001.481] I> 29) Base:0xf1400000 Size:0x00400000
[0001.485] I> 30) Base:0xf0a00000 Size:0x00100000
[0001.490] I> 31) Base:0x00000000 Size:0x00000000
[0001.494] I> 32) Base:0xf8000000 Size:0x08000000
[0001.499] I> 33) Base:0x00000000 Size:0x00000000
[0001.503] I> 34) Base:0xf3c00000 Size:0x01000000
[0001.507] I> 35) Base:0xab000000 Size:0x01000000
[0001.512] I> 36) Base:0xa0000000 Size:0x0b000000
[0001.516] I> 37) Base:0xf2800000 Size:0x00800000
[0001.521] I> 38) Base:0x80000000 Size:0x20000000
[0001.525] I> 39) Base:0xb0000000 Size:0x08000000
[0001.530] I> 40) Base:0x00000000 Size:0x00000000
[0001.534] I> 41) Base:0x00000000 Size:0x00000000
[0001.539] I> 42) Base:0x00000000 Size:0x00000000
[0001.543] I> 43) Base:0x00000000 Size:0x00000000
[0001.548] I> 44) Base:0x00000000 Size:0x00000000
[0001.552] I> 45) Base:0x00000000 Size:0x00000000
[0001.557] GIC-SPI Target CPU: 0
[0001.560] Interrupts Init done
[0001.562] calling constructors
[0001.565] initializing heap
[0001.568] I> Heap: [0xa06905a8 ... 0xab000000]
[0001.572] initializing threads
[0001.575] initializing timers
[0001.578] creating bootstrap completion thread
[0001.582] top of bootstrap2()
[0001.585] CPU: MIDR: 0x4E0F0040, MPIDR: 0x80000000
[0001.590] initializing platform
[0001.593] E> DEVICE_PROD: Invalid value data = 0, size = 0.
[0001.598] W> device prod register failed
[0001.602] I> Bl_dtb @0xaaf00000
[0001.608] W> "plugin-manager" doesn't exist, creating
[0001.610] W> "ids" doesn't exist, creating
[0001.614] W> "connection" doesn't exist, creating
[0001.618] W> "configs" doesn't exist, creating
[0001.631] I> Find /i2c@3160000's alias i2c0
[0001.631] I> Reading eeprom i2c=0 address=0x50
[0001.657] I> Device at /i2c@3160000:0x50
[0001.657] I> Reading eeprom i2c=0 address=0x56
[0001.681] I> Device at /i2c@3160000:0x56
[0001.683] I> Find /i2c@3180000's alias i2c2
[0001.684] I> Reading eeprom i2c=2 address=0x54
[0001.685] E> I2C: slave not found in slaves.
[0001.686] E> I2C: Could not write 0 bytes to slave: 0x00a8 with repeat start true.
[0001.687] E> I2C_DEV: Failed to send register address 0x00000000.
[0001.687] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa8 at 0x00000000 via instance 2.
[0001.695] E> eeprom: Failed to read I2C slave device
[0001.700] I> Eeprom read failed 0x3526070d
[0001.704] I> Reading eeprom i2c=2 address=0x57
[0001.709] E> I2C: slave not found in slaves.
[0001.713] E> I2C: Could not write 0 bytes to slave: 0x00ae with repeat start true.
[0001.721] E> I2C_DEV: Failed to send register address 0x00000000.
[0001.726] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xae at 0x00000000 via instance 2.
[0001.736] E> eeprom: Failed to read I2C slave device
[0001.740] I> Eeprom read failed 0x3526070d
[0001.744] I> Reading eeprom i2c=2 address=0x52
[0001.749] E> I2C: slave not found in slaves.
[0001.753] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true.
[0001.761] E> I2C_DEV: Failed to send register address 0x00000000.
[0001.766] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 2.
[0001.776] E> eeprom: Failed to read I2C slave device
[0001.780] I> Eeprom read failed 0x3526070d
[0001.785] I> Find /i2c@c240000's alias i2c1
[0001.788] I> Reading eeprom i2c=1 address=0x52
[0001.794] E> I2C: slave not found in slaves.
[0001.797] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true.
[0001.805] E> I2C_DEV: Failed to send register address 0x00000000.
[0001.810] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 1.
[0001.820] E> eeprom: Retry to read I2C slave device.
[0001.825] E> I2C: slave not found in slaves.
[0001.829] E> I2C: Could not write 0 bytes to slave: 0x00a4 with repeat start true.
[0001.837] E> I2C_DEV: Failed to send register address 0x00000000.
[0001.842] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa4 at 0x00000000 via instance 1.
[0001.852] E> eeprom: Failed to read I2C slave device
[0001.856] I> Eeprom read failed 0x3526070d
[0001.860] I> Reading eeprom i2c=1 address=0x50
[0001.865] E> I2C: slave not found in slaves.
[0001.869] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true.
[0001.877] E> I2C_DEV: Failed to send register address 0x00000000.
[0001.882] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0x00000000 via instance 1.
[0001.892] E> eeprom: Retry to read I2C slave device.
[0001.897] E> I2C: slave not found in slaves.
[0001.901] E> I2C: Could not write 0 bytes to slave: 0x00a0 with repeat start true.
[0001.908] E> I2C_DEV: Failed to send register address 0x00000000.
[0001.914] E> I2C_DEV: Could not read 256 registers of size 1 from slave 0xa0 at 0x00000000 via instance 1.
[0001.924] E> eeprom: Failed to read I2C slave device
[0001.928] I> Eeprom read failed 0x3526070d
[0001.932] I> create_pm_ids: id: 2888-0001-400-H, len: 15
[0001.937] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93
[0001.948] I> create_pm_ids: id: 2822-0000-500-F, len: 15
[0001.954] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93
[0001.965] I> Adding plugin-manager/ids/2888-0001-400=/i2c@3160000:module@0x50
[0001.973] W> "i2c@3160000" doesn't exist, creating
[0001.976] W> "module@0x50" doesn't exist, creating
[0001.981] I> Adding plugin-manager/ids/2822-0000-500=/i2c@3160000:module@0x56
[0001.988] W> "module@0x56" doesn't exist, creating
[0001.995] I> Adding plugin-manager/cvm
[0001.997] W> "chip-id" doesn't exist, creating
[0002.000] I> Adding plugin-manager/chip-id/A02
[0002.005] I> Plugin-manager override starting
[0002.010] I> node /plugin-manager/fragement-tegra-wdt-en matches
[0002.019] I> node /plugin-manager/fragement-soft-wdt matches
[0002.027] I> node /plugin-manager/fragment-pcie-c5-rp matches
[0002.032] I> node /plugin-manager/fragment-tegra-ufs-lane10 matches
[0002.041] I> Disable plugin-manager status in FDT
[0002.041] I> Plugin-manager override finished successfully
[0002.042] I> gpio framework initialized
[0002.047] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio' driver
[0002.054] I> tegrabl_gpio_driver_register: register 'nvidia,tegra194-gpio-aon' driver
[0002.061] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x46
[0002.069] E> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539
[0002.076] E> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539
[0002.082] W> tegrabl_tca9539_init: failed to fetch phandle from dt
[0002.088] I> tegrabl_tca9539_init: i2c bus: 1, slave addr: 0x44
[0002.096] E> fetch_driver_phandle_from_dt: failed to get node with compatible ti,tca9539
[0002.104] E> fetch_driver_phandle_from_dt: failed to get node with compatible nxp,tca9539
[0002.110] W> tegrabl_tca9539_init: failed to fetch phandle from dt
[0002.118] I> fixed regulator driver initialized
[0002.132] I> register 'maxim' power off handle
[0002.133] I> virtual i2c enabled
[0002.133] I> registered 'maxim,max20024' pmic
[0002.133] I> tegrabl_gpio_driver_register: register 'max20024-gpio' driver
[0002.139] I> Boot-device: eMMC
[0002.142] I> Boot_device: SDMMC_BOOT instance: 3
[0002.151] I> sdmmc-3 params source = boot args
[0002.151] I> create_pm_ids: id: 2888-0001-400-H, len: 15
[0002.156] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93
[0002.167] I> create_pm_ids: id: 2822-0000-500-F, len: 15
[0002.172] I> config: mem-type:00,power-config:00,misc-config:00,modem-config:00,touch-config:00,display-config:00,, len: 93
[0002.183] I> sdmmc bdev is already initialized
[0002.187] I> sdmmc-3 params source = boot args
[0002.218] I> Found 17 partitions in SDMMC_BOOT (instance 3)
[0002.230] I> Found 42 partitions in SDMMC_USER (instance 3)
[0002.239] I> enabling 'vdd-hdmi-5v0' regulator
[0002.244] I> regulator 'vdd-hdmi-5v0' already enabled
[0002.245] I> hdmi cable connected
[0002.247] W> set volts not configured for 'vdd-1v0'
[0002.249] W> set volts not configured for 'vdd-1v8-hs'
[0002.253] E> invalid display type
[0002.256] E> invalid display type
[0002.257] E> cannot find any other nvdisp nodes
[0002.273] I> edid read success
[0002.285] I> edid read success
[0002.285] I> width = 640, height = 480, frequency = 25174825
[0002.286] I> width = 640, height = 480, frequency = 25174825
[0002.286] I> width = 640, height = 480, frequency = 25174825
[0002.287] I> width = 640, height = 480, frequency = 25174825
[0002.287] I> width = 3840, height = 2160, frequency = 594000000
[0002.291] I> width = 1920, height = 1080, frequency = 148500000
[0002.297] I> width = 1920, height = 540, frequency = 74250000
[0002.302] I> width = 3840, height = 2160, frequency = 593406593
[0002.308] I> width = 1920, height = 1080, frequency = 148351648
[0002.314] I> width = 1920, height = 1080, frequency = 148351648
[0002.319] I> width = 1280, height = 720, frequency = 74175824
[0002.325] I> width = 1280, height = 720, frequency = 74175824
[0002.331] I> width = 1920, height = 1080, frequency = 74175824
[0002.336] I> width = 1920, height = 1080, frequency = 74175824
[0002.342] I> width = 1920, height = 1080, frequency = 74175824
[0002.348] I> width = 3840, height = 2160, frequency = 296703296
[0002.354] I> width = 720, height = 480, frequency = 26973026
[0002.359] I> width = 720, height = 576, frequency = 26973026
[0002.365] I> width = 3840, height = 2160, frequency = 296703296
[0002.370] I> width = 3840, height = 2160, frequency = 296703296
[0002.376] I> width = 3840, height = 2160, frequency = 296703296
[0002.382] I> width = 4096, height = 2160, frequency = 296703296
[0002.388] I> Best mode Width = 1920, Height = 1080, freq = 148351648
[0002.398] I> hdmi_enable, starting HDMI initialisation
[0002.403] I> hdmi_enable, HDMI initialisation complete
[0002.413] I> Load in CBoot Boot Options partition and parse it
[0002.420] E> Error -9 when finding node with path /boot-configuration
[0002.420] E> tegrabl_cbo_parse_info: "boot-configuration" not found in CBO file.
[0002.423] I> Hit any key to stop autoboot: 4 3 2 1
[0004.431] initializing target
[0004.431] calling apps_init()
[0004.432] starting app kernel_boot_app
[0004.451] I> found decompressor handler: lz4-legacy
[0004.452] I> decompressing BMP blob ...
[0004.455] I> Kernel type = Normal
[0004.455] I> Loading kernel-bootctrl from partition
[0004.456] I> Loading partition kernel-bootctrl at 0xa4ac0000 from device(0x1)
[0004.462] W> tegrabl_get_kernel_bootctrl: magic number(0x00000000) is invalid
[0004.463] W> tegrabl_get_kernel_bootctrl: use default dummy boot control data
[0004.464] I> ########## SD boot ##########
[0004.468] I> No sdcard
[0004.470] I> -0 params source =
[0004.473] E> Blockdev open: exit error
[0004.476] E> SD boot failed, err: 724238353
[0004.480] I> ########## USB boot ##########
[0004.501] I> USB Firmware Version: 60.06 release
[0004.557] I> regulator of usb2-0 already enabled
[0004.563] I> regulator of usb2-1 already enabled
[0004.569] I> regulator of usb2-2 already enabled
[0004.578] I> enabling 'vdd-5v-sata' regulator
[0005.583] E> failed to initialize xhci controller
[0005.583] E> Error in init of XUSB host driver, err: 79790026
[0005.583] E> Failed to initialize device 5-0
[0005.584] E> USB boot failed, err: 2037973030
[0005.584] I> ########## Fixed storage boot ##########
[0005.584] I> Already published: 00010003
[0005.585] I> Look for boot partition
[0005.588] I> Fallback: assuming 0th partition is boot partition
[0005.594] I> Detect filesystem
[0005.621] I> Loading extlinux.conf ...
[0005.621] I> rootfs path: /sdmmc_user/boot/extlinux/extlinux.conf
[0005.658] I> L4T boot options
[0005.658] I> [1]: "primary kernel"
[0005.659] I> Enter choice:
[0008.660] I> Continuing with default option: 1
[0008.660] I> Loading kernel sig file from rootfs ...
[0008.660] I> rootfs path: /sdmmc_user/boot/Image.sig
[0008.679] I> Loading kernel binary from rootfs ...
[0008.679] I> rootfs path: /sdmmc_user/boot/Image
[0008.916] I> Validate kernel ...
[0008.916] I> T19x: Authenticate kernel (bin_type: 37), max size 0x5000000
[0009.227] E> digest on binary did not match!!
[0009.228] C> OEM authentication of kernel payload failed!
[0009.228] W> Failed to validate kernel binary (err=1077936152, fail=0)
[0009.229] W> Security fuse not burned, ignore validation failure
[0009.236] I> No kernel-dtb binary path
[0009.242] I> A/B: bin_type (38) slot 1
[0009.242] I> Loading kernel-dtb_b from partition
[0009.243] I> Loading partition kernel-dtb_b at 0x91000000 from device(0x1)
[0009.253] I> Validate kernel-dtb ...
[0009.254] I> T19x: Authenticate kernel-dtb (bin_type: 38), max size 0x400000
[0009.257] I> Loading ramdisk from rootfs ...
[0009.258] I> rootfs path: /sdmmc_user/boot/initrd
[0009.310] I> Kernel hdr @0xa4ac0000
[0009.310] I> Kernel dtb @0x90000000
[0009.310] I> decompressor handler not found
[0009.311] I> Copying kernel image (34330632 bytes) from 0xa4ac0000 to 0x80080000 ... [0009.321] I> Done
[0009.322] I> Updated bpmp info to DTB
[0009.323] I> Ramdisk: Base: 0x92000000; Size: 0x54ecaf
[0009.323] I> Updated initrd info to DTB
[0009.324] W> WARN: Fail to override "console=none" in commandline
[0009.324] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params
[0009.330] E> tegrabl_linuxboot_add_disp_param, du 1 failed to get display params
[0009.337] I> Active slot suffix: _b
[0009.341] I> add_boot_slot_suffix: slot_suffix = _b
[0009.345] I> Linux Cmdline: console=ttyTCU0,115200 video=tegrafb no_console_suspend=1 earlycon=tegra_comb_uart,mmio32,0x0c168000 gpt tegra_fbmem=0x800000@0xa069c000 lut_mem=0
[0009.375] I> Updated bootarg info to DTB
[0009.379] W> MAC addr invalid!
[0009.382] E> Failed to get WIFI MAC address
[0009.386] W> MAC addr invalid!
[0009.389] E> Failed to get Bluetooth MAC address
[0009.393] I> eeprom_get_mac_addr: MAC (type: 2): 00:04:4b:c7:bb:2a
[0009.400] W> "plugin-manager" doesn't exist, creating
[0009.404] I> Adding /chosen/plugin-manager/cvm
[0009.408] W> "chip-id" doesn't exist, creating
[0009.413] I> Adding /chosen/plugin-manager/chip-id
[0009.417] W> "configs" doesn't exist, creating
[0009.422] I> Adding /chosen/plugin-manager/configs
[0009.426] W> "ids" doesn't exist, creating
[0009.430] I> Adding /chosen/plugin-manager/ids
[0009.435] W> "odm-data" doesn't exist, creating
[0009.439] I> Adding /chosen/plugin-manager/odm-data
[0009.446] W> "memory" doesn't exist, creating
[0009.448] I> [0] START: 0x80000000, END: 0xac000000
[0009.452] I> [1] START: 0xac004000, END: 0xf09d0000
[0009.457] I> [2] START: 0xf09dc000, END: 0xf09e0000
[0009.462] I> dram_block larger than 80000000
[0009.466] I> [3] START: 0x100000000, END: 0x480000000
[0009.471] I> added [base:0x80000000, size:0x2c000000] to /memory
[0009.477] I> added [base:0xac200000, size:0x44600000] to /memory
[0009.483] I> added [base:0x100000000, size:0x380000000] to /memory
[0009.490] I> Updated memory info to DTB
[0009.493] E> add_disp_param: failed to get display params for du=1
[0009.499] W> "reset" doesn't exist, creating
[0009.503] I> NVG: Logical CPU: 0; MPIDR: 0x80000000
[0009.507] I> NVG: Logical CPU: 1; MPIDR: 0x80000001
[0009.512] I> NVG: Logical CPU: 2; MPIDR: 0x80000100
[0009.517] I> NVG: Logical CPU: 3; MPIDR: 0x80000101
[0009.521] I> NVG: Logical CPU: 4; MPIDR: 0x80000200
[0009.526] I> NVG: Logical CPU: 5; MPIDR: 0x80000201
[0009.531] I> NVG: Logical CPU: 6; MPIDR: 0x80000300
[0009.536] I> NVG: Logical CPU: 7; MPIDR: 0x80000301
[0009.541] W> "misc-data" doesn't exist, creating
[0009.545] I> Boot-device: eMMC
[0009.548] I> Add boot-sdmmc to plugin-manager/misc-data
[0009.553] I> Add storage-sdmmc to plugin-manager/misc-data
[0009.558] W> Unknown storage device
[0009.562] I> Add serial number:[REDACTED] as DT property
[0009.568] I> Plugin-manager override starting
[0009.571] I> node /plugin-manager/fragement-tegra-wdt-en matches
[0009.579] I> node /plugin-manager/fragement-soft-wdt matches
[0009.586] I> node /plugin-manager/fragment-pcie-c5-rp matches
[0009.591] I> node /plugin-manager/fragment-tegra-ufs-lane10 matches
[0009.603] I> Disable plugin-manager status in FDT
[0009.603] I> Plugin-manager override finished successfully
[0009.604] I> tegrabl_load_kernel_and_dtb: Done
[0009.653] I> Kernel EP: 0x80080000, DTB: 0x90000000
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.140-tegra (buildbrain@mobile-u64-3357) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Lin0
[ 0.000000] Boot CPU: AArch64 Processor [4e0f0040]
[ 0.000000] OF: fdt:memory scan node memory, reg size 48,
[ 0.000000] OF: fdt: - 80000000 , 2c000000
[ 0.000000] OF: fdt: - ac200000 , 44600000
[ 0.000000] OF: fdt: - 100000000 , 380000000
[ 0.000000] earlycon: tegra_comb_uart0 at MMIO32 0x000000000c168000 (options '')
[ 0.000000] bootconsole [tegra_comb_uart0] enabled
[ 0.000000] Found tegra_fbmem: 00800000@a069c000
[ 0.000000] Found lut_mem: 00002008@a0697000
��WARNING: pll_d3 has no dyn ramp
��bash: cannot set terminal process group (-1): Inappropriate ioctl for device
bash: no job control in this shell
Then, I realized i snipped off the bash prompt at the end, so I rebooted again. Realizing i specified the wrong TTY, i powered off (causing an unclean unmount of teh NVMe), and retried… and it booted.
[0009.638] I> Kernel EP: 0x80080000, DTB: 0x90000000
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.140-tegra (buildbrain@mobile-u64-3357) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Lin0
[ 0.000000] Boot CPU: AArch64 Processor [4e0f0040]
[ 0.000000] OF: fdt:memory scan node memory, reg size 48,
[ 0.000000] OF: fdt: - 80000000 , 2c000000
[ 0.000000] OF: fdt: - ac200000 , 44600000
[ 0.000000] OF: fdt: - 100000000 , 380000000
[ 0.000000] earlycon: tegra_comb_uart0 at MMIO32 0x000000000c168000 (options '')
[ 0.000000] bootconsole [tegra_comb_uart0] enabled
[ 0.000000] Found tegra_fbmem: 00800000@a069c000
[ 0.000000] Found lut_mem: 00002008@a0697000
��WARNING: pll_d3 has no dyn ramp
��[ 6.147453] cgroup: cgroup2: unknown option "nsdelegate"
[ 7.672332] EXT4-fs (nvme0n1p6): warning: mounting unchecked fs, running e2fsck is recommended
[ 12.343943] using random self ethernet address
[ 12.344094] using random host ethernet address
[ 12.354405] random: crng init done
[ 12.354525] random: 7 urandom warning(s) missed due to ratelimiting
[ 12.782666] using random self ethernet address
[ 12.782670] using random host ethernet address
Ubuntu 18.04.4 LTS hostname ttyTCU0
So no clue what happened there. It works, now. The only difference seems to be the filesystem was not cleanly unmounted, and yet that fixed it? Waiting for me at login was an update for the Coral modules.
$ sudo apt update && sudo apt dist-upgrade -y --autoremove
[sudo] password for username:
Hit:1 https://packages.cloud.google.com/apt coral-edgetpu-stable InRelease
Hit:2 http://ports.ubuntu.com/ubuntu-ports bionic InRelease
Hit:3 http://ports.ubuntu.com/ubuntu-ports bionic-updates InRelease
Hit:4 http://ports.ubuntu.com/ubuntu-ports bionic-backports InRelease
Hit:5 https://repo.download.nvidia.com/jetson/ffmpeg main InRelease
Hit:6 https://repo.download.nvidia.com/jetson/common r32.4 InRelease
Hit:7 http://ports.ubuntu.com/ubuntu-ports bionic-security InRelease
Hit:8 https://repo.download.nvidia.com/jetson/t194 r32.4 InRelease
Reading package lists... Done
Building dependency tree
Reading state information... Done
1 package can be upgraded. Run 'apt list --upgradable' to see it.
Reading package lists... Done
Building dependency tree
Reading state information... Done
Calculating upgrade... Done
The following packages will be upgraded:
gasket-dkms
1 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
Need to get 46.2 kB of archives.
After this operation, 0 B of additional disk space will be used.
Get:1 https://packages.cloud.google.com/apt coral-edgetpu-stable/main arm64 gasket-dkms all 1.0-12 [46.2 kB]
Fetched 46.2 kB in 0s (112 kB/s)
debconf: delaying package configuration, since apt-utils is not installed
(Reading database ... 200449 files and directories currently installed.)
Preparing to unpack .../gasket-dkms_1.0-12_all.deb ...
-------- Uninstall Beginning --------
Module: gasket
Version: 1.0
Kernel: 4.15.0-109-generic (aarch64)
-------------------------------------
Status: Before uninstall, this module version was ACTIVE on this kernel.
gasket.ko:
- Uninstallation
- Deleting from: /lib/modules/4.15.0-109-generic/updates/dkms/
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
apex.ko:
- Uninstallation
- Deleting from: /lib/modules/4.15.0-109-generic/updates/dkms/
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
depmod...
Warning: Unable to find an initial ram disk that I know how to handle.
Will not try to make an initrd.
DKMS: uninstall completed.
-------- Uninstall Beginning --------
Module: gasket
Version: 1.0
Kernel: 4.9.140-tegra (aarch64)
-------------------------------------
Status: Before uninstall, this module version was ACTIVE on this kernel.
gasket.ko:
- Uninstallation
- Deleting from: /lib/modules/4.9.140-tegra/updates/dkms/
- Original module
- No original module was found for this module on this kernel.
- Use the dkms install command to reinstall any previous module version.
Progress: [ 0%] [..........................................................]
- Uninstallation
Done.
Unpacking gasket-dkms (1.0-12) over (1.0-11) ...............................]
Setting up gasket-dkms (1.0-12) ...
Loading new gasket-1.0 DKMS files...
It is likely that 4.9.140-tegra belongs to a chroot's host
Building for 4.15.0-108-generic, 4.15.0-109-generic and 4.9.140-tegra
Module build for kernel 4.15.0-108-generic was skipped since the
kernel headers for this kernel does not seem to be installed.
Building initial module for 4.15.0-109-generic
Done.
gasket:
Running module version sanity check.
- Original module
- No original module exists within this kernel
- Installation
- Installing to /lib/modules/4.15.0-109-generic/updates/dkms/
apex.ko:
Running module version sanity check.
- Original module
- No original module exists within this kernel
- Installation
- Installing to /lib/modules/4.15.0-109-generic/updates/dkms/
depmod...
Warning: Unable to find an initial ram disk that I know how to handle.
Will not try to make an initrd.
DKMS: install completed.
Building initial module for 4.9.140-tegra
Done.
gasket:
Running module version sanity check.
- Original module
- No original module exists within this kernel
- Installation
- Installing to /lib/modules/4.9.140-tegra/updates/dkms/
apex.ko:
Running module version sanity check.
- Original module
- No original module exists within this kernel
- Installation
- Installing to /lib/modules/4.9.140-tegra/updates/dkms/
depmod...
Backing up initrd.img-4.9.140-tegra to /boot/initrd.img-4.9.140-tegra.old-dkms
Making new initrd.img-4.9.140-tegra
(If next boot fails, revert to initrd.img-4.9.140-tegra.old-dkms image)
update-initramfs.....
DKMS: install completed.
and rebooting… and it works. I assume I can put my Coral back in now that a module is rebuilt. Any insight as to what might have gone wrong? I’m unsure whether to blame the DKMS, the Coral modules, or the NVMe configuration here.
Edit: yeah, it boots with the coral inserted and the modules for it are loaded.
Edit2: I didnt’ put 2 and 2 together immeidatley, but somebody reported this an issue on my GitHub the other day, so I don’t think it’s NVMe or Coral related per the note at the bottom of this post it may be a bad kernel package that did it. I still have no earthly idea why it’s booting now.
Edit: per post directly below, it might be NVMe related, actually.