Hello, our team has developed a camera driver and device tree file for the IMX327 sensor on an Orin NX (with a custom carrier board). Currently, the camera can successfully capture video using commands such as video-viewer and GStreamer. However, we’ve encountered an issue: whenever we use the v4l2-…

No more questions for now, thank you

Here is the kernel log information when running the v4l2-ctl -d /dev/video0 --set-fmt-video=width=1920,height=1080 --set-ctrl bypass_mode=0 --stream-mmap --stream-count=100 command. [ 172.635576] bwmgr API not supported [ 172.636573] imx327_set_mode [ 172.640194] imx327_write_table [ 172.85878…

Look like didn’t receive any data from the trace log. Suppose it could be incomplete sensor REG configuration cause the problem.

I’m not very familiar with this, but is it possible that an incomplete register configuration is causing v4l2-ctl to fail when capturing RAW images, while still allowing GStreamer to capture video successfully? Currently, the camera functions normally when using video-viewer to acquire video images. …

It’s working by gst-launch-1.0 nvarguscamerasrc … command? You can use nvargus_nvraw for raw capture alternative. Thanks

1)Thank you for your response. Yes, the following commands can all successfully capture video images. Additionally, we have previously confirmed that the nvargus_nvraw command can indeed capture RAW format images for imx327. nvgstcapture-1.0 --sensor-id=0 gst-launch-1.0 nvarguscamerasrc sensor-id=0…

Review the port-index/tegra_sinterface/num_lanes/bus-width then, Maybe make the control function(CID) in sensor driver to dummy function to make sure the REG configuration the same both for v4l2-ctl with argus.

Here is the relevant portion of the device tree for the ToF camera. These node properties should be correct, right? I am using a 4-lane ToF camera, which is connected to the third interface (J21) on the custom carrier board. [图片] i2c_cam2:i2c@2 { reg = <2>; i2c-mux,deselect-on-exit; #…

You may need to probe by scope. Thanks

Is this still an issue to support? Any result can be shared?

We have modified the device tree and driver so that we can now capture RAW format images through nvargus. However, I still have some questions: The nvargus_nvraw tool seems to only capture one RAW image at a time. Is there a way to obtain consecutive frames? Additionally, the mlx75027 should outpu…

Failure in image capture and streaming using v4l2

Robotics & Edge Computing Jetson Systems Jetson Orin NX

system Closed April 24, 2025, 12:32am 20

This topic was automatically closed 14 days after the last reply. New replies are no longer allowed.

Topic		Replies	Views
V4l2-ctl can not capture raw data Jetson Orin Nano camera	9	413	May 31, 2024
V4l2 cpature error GLOBAL type:STREAM_VC phy:0 Jetson AGX Orin gstreamer	13	1833	September 1, 2022
Error occurs when capturing images using nvargus_nvraw Jetson AGX Orin camera	10	89	January 9, 2026
Sony Image Sensor works with nvarguscamerasrc but not with v4l2src Jetson Orin Nano camera , gstreamer	6	195	November 7, 2024
How do I display a camera image on the screen Jetson Orin Nano camera	20	1535	May 13, 2024
Failures of v4l2-compliance Jetson Orin NX camera	8	233	July 1, 2025
Unable to stream imx334 with v4l2 driver on Nvidia Jetson Xavier NX where the same dts works for tegra driver(nvargs) Jetson Xavier NX camera	104	1234	November 20, 2024
[R35.1]Jetson Orin nvargus_nvraw can not capture image Jetson AGX Orin camera	17	1719	March 7, 2023
Jetson Xavier NX: CSI Camera Streaming Problem Jetson Xavier NX camera	13	2204	November 17, 2021
MT9M021 Streaming Jetson TX1	45	7107	October 18, 2021

Failure in image capture and streaming using v4l2

Related topics