Hi d.a.mahabiersing,
I tried the image you sent and it progressed further into startup but it still fails. The eeprom error seems to be a showstopper. The terminal is unresponsive after sending the following:
[0000.126] [TegraBoot] (version 00.00.2018.01-l4t-33e7fa82)
[0000.131] Processing in cold boot mode Bootloader 2
[0000.136] A02 Bootrom Patch rev = 1023
[0000.139] Power-up reason: pmc por
[0000.142] No Battery Present
[0000.145] pmic max77620 reset reason
[0000.148] pmic max77620 NVERC : 0x40
[0000.152] RamCode = 0
[0000.154] Platform has DDR4 type RAM
[0000.157] max77620 disabling SD1 Remote Sense
[0000.161] Setting DDR voltage to 1125mv
[0000.165] Serial Number of Pmic Max77663: 0x108f6
[0000.173] Entering ramdump check
[0000.176] Get RamDumpCarveOut = 0x0
[0000.179] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8
[0000.184] Last reboot was clean, booting normally!
[0000.189] Sdram initialization is successful
[0000.193] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.199] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.205] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.211] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.217] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.223] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.234] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.256] Platform-DebugCarveout: 0
[0000.260] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.265] Non secure mode, and RB not enabled.
[0000.272] Invalid GPT Partition
[0000.287] Using BFS PT to query partitions
[0000.291] failed to load NvTbootTbootCpu from (2:0)
[0000.296] re-load NvTbootTbootCpu from (4:0)
[0000.434] Csd NumOfBlocks=124735488
[0000.493] Using GPT Primary to query partitions
[0000.502] Loading Tboot-CPU binary
[0000.878] Verifying TBC in OdmNonSecureSBK mode
[0000.888] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.895] Bootloader downloaded successfully.
[0000.900] Downloaded Tboot-CPU binary to 0xa0000258
[0000.905] MAX77620_GPIO5 configured
[0000.908] CPU power rail is up
[0000.911] CPU clock enabled
[0000.915] Performing RAM repair
[0000.917] Updating A64 Warmreset Address to 0xa00002e9
[0000.923] Loading NvTbootBootloaderDTB
[0002.234] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0002.295] Bootloader DTB Load Address: 0x83000000
[0002.300] Loading NvTbootKernelDTB
[0003.610] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0003.671] Kernel DTB Load Address: 0x83100000
[0003.682] Loading cboot binary
[0005.363] Verifying EBT in OdmNonSecureSBK mode
[0005.405] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0005.412] Bootloader downloaded successfully.
[0005.606] Using BFS PT to query partitions
[0005.610] Next binary entry address: 0x92c00258
[0005.614] BoardId: 3448
[0005.619] Overriding pmu board id with proc board id
[0005.624] Display board id is not available
[0007.122] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0007.175] /bpmp deleted
[0007.177] SC7EntryFw header found loaded at 0xff700000
[0007.369] OVR2 PMIC
[0007.371] Bpmp FW successfully loaded
[0007.389] WB0 init successfully at 0xff780000
[0007.393] Set NvDecSticky Bits
[0007.397] GSC2 address ff53fffc value c0edbbcc
[0007.403] GSC MC Settings done
[0007.410] TOS Image length 53680
[0007.413] Monitor size 53680
[0007.416] OS size 0
[0007.579] Secure Os AES-CMAC Verification Success!
[0007.584] TOS image cipher info: plaintext
[0007.587] Loading and Validation of Secure OS Successful
[0007.603] SC7 Entry Firmware - 0xff700000, 0x4000
[0007.608] NvTbootPackSdramParams: start.
[0007.613] NvTbootPackSdramParams: done.
[0007.617] Tegraboot started after 53294 us
[0007.621] Basic modules init took 5710447 us
[0007.625] NvTbootQspiFlashIoctl: Opcode = 1 not supported
[0007.630] Sec Bootdevice Read Time = 12 ms, Read Size = 65 KB
[0007.636] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0007.641] Storage Device Read Time = 6747 ms, Read Size = 2306 KB
[0007.647] Storage Device Write Time = 0 ms, Write Size = 0 KB
[0007.653] Next stage binary read took 1529701 us
[0007.657] Carveout took -1541380 us
[0007.660] CPU initialization took 2048065 us
[0007.664] Total time taken by TegraBoot 7746833 us
[0007.669] Starting CPU & Halting co-processor
64NOTICE: BL31: v1.3(release):eca0c5e
NOTICE: BL31: Built : 00:21:27, Mar 13 2019
ERROR: Error initializing runtime service trusty_fast
[0007.791] RamCode = 0
[0007.796] LPDDR4 Training: Read DT: Number of tables = 2
[0007.801] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0007.814] EMC Training Successful
[0007.817] 408000 not found in DVFS table
[0007.823] RamCode = 0
[0007.827] DT Write: emc-table@204000 succeeded
[0007.832] DT Write: emc-table@1600000 succeeded
[0007.836] LPDDR4 Training: Write DT: Number of tables = 2
[0008.033]
[0008.034] Debug Init done
[0008.037] Marked DTB cacheable
[0008.040] Bootloader DTB loaded at 0x83000000
[0008.045] Marked DTB cacheable
[0008.048] Kernel DTB loaded at 0x83100000
[0008.052] DeviceTree Init done
[0008.064] Pinmux applied successfully
[0008.068] gicd_base: 0x50041000
[0008.072] gicc_base: 0x50042000
[0008.075] Interrupts Init done
[0008.079] Using base:0x60005090 & irq:208 for tick-timer
[0008.084] Using base:0x60005098 for delay-timer
[0008.088] platform_init_timer: DONE
[0008.092] Timer(tick) Init done
[0008.096] osc freq = 38400 khz
[0008.100]
[0008.101] welcome to cboot
[0008.103]
[0008.104] Cboot Version: 00.00.2018.01-t210-f76b856b
[0008.109] calling constructors
[0008.112] initializing heap
[0008.115] initializing threads
[0008.118] initializing timers
[0008.121] creating bootstrap completion thread
[0008.125] top of bootstrap2()
[0008.128] CPU: ARM Cortex A57
[0008.131] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0008.136] initializing platform
[0008.139] Scratch reg 37 & 271 initial value set..
[0008.145] cboot:secure-pmc present
[0008.148] Manufacturer: MF = 0xc2, ID MSB = 0x25
[0008.153] ID LSB = 0x36, ID-CFI len = 194 bytes
[0008.157] Macronix QSPI chip present
[0008.161] SPI device register
[0008.164] init boot device
[0008.166] allocating memory for boot device(SPI)
[0008.171] registering boot device
[0008.180] sdmmc node status = okay
[0008.184] sdcard instance = 0
[0008.186] sdcard gpio handle 0x5d
[0008.190] sdcard gpio pin 0xc9
[0008.193] sdcard gpio flags 0x0
[0008.196] vmmc-supply 0x9d
[0008.198] Instance: 0
[0008.200] Allocating memory for context
[0008.204] enabling clock
[0008.207] sd card init
[0008.209] Check card present and stable
[0008.213] Send command 0
[0008.237] Send command 3
[0008.241] Set RCA for the card
[0008.244] Query card specific data by command 9
[0008.251] Parse CSD data
[0008.253] Send command 7
[0008.264] Calling sd device register
[0008.267] Init sdcard
[0008.269] Allocating memory for boot device
[0008.273] Registering user device
[0008.286] Enable APE clock
[0008.289] Un-powergate APE partition
[0008.293] of_register: registering tegra_udc to of_hal
[0008.298] of_register: registering tegra_udc to of_hal
[0008.303] of_register: registering inv20628-driver to of_hal
[0008.308] of_register: registering ads1015-driver to of_hal
[0008.314] of_register: registering lp8557-bl-driver to of_hal
[0008.320] of_register: registering bq2419x_charger to of_hal
[0008.325] of_register: registering cpc to of_hal
[0008.330] of_register: registering bq27441_fuel_gauge to of_hal
[0008.341] gpio framework initialized
[0008.345] of_register: registering tca9539_gpio to of_hal
[0008.350] of_register: registering tca9539_gpio to of_hal
[0008.355] of_register: registering i2c_bus_driver to of_hal
[0008.361] of_register: registering i2c_bus_driver to of_hal
[0008.367] of_register: registering i2c_bus_driver to of_hal
[0008.372] of_register: registering i2c_bus_driver to of_hal
[0008.378] pmic framework initialized
[0008.381] of_register: registering max77620_pmic to of_hal
[0008.387] regulator framework initialized
[0008.391] of_register: registering tps65132_bl_driver to of_hal
[0008.397] initializing target
[0008.402] gpio_driver_register: register 'tegra_gpio_driver' driver
[0008.411] fixed regulator driver initialized
[0008.429] initializing OF layer
[0008.432] NCK carveout not present
[0008.435] Skipping dts_overrides
[0008.439] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0008.455] I2C Bus Init done
[0008.457] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0008.468] I2C Bus Init done
[0008.470] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0008.480] I2C Bus Init done
[0008.483] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0008.493] I2C Bus Init done
[0008.496] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0008.506] I2C Bus Init done
[0008.509] of_children_init: Ops found for compatible string maxim,max77620
[0008.519] max77620_init using irq 118
[0008.524] register 'maxim,max77620' pmic
[0008.528] gpio_driver_register: register 'max77620-gpio' driver
[0008.535] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0008.545] I2C Bus Init done
[0008.549] NCK carveout not present
[0008.552] shim_invoke: No NCT, Calling dts updates
[0008.563] Find /i2c@7000c000's alias i2c0
[0008.567] get eeprom at 1-a0, size 256, type 0
[0008.575] Find /i2c@7000c500's alias i2c2
[0008.579] get eeprom at 3-a0, size 256, type 0
[0008.584] get eeprom at 3-ae, size 256, type 0
[0008.588] pm_ids_update: Updating 1,a0, size 256, type 0
[0008.593] I2C slave not started
[0008.596] I2C write failed
[0008.599] Writing offset failed
[0008.602] eeprom_init: EEPROM read failed
[0008.606] pm_ids_update: eeprom init failed
[0008.610] pm_ids_update: Updating 3,a0, size 256, type 0
[0008.640] pm_ids_update: The pm board id is 3448-0000-200
[0008.647] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0008.655] pm_ids_update: pm id update successful
[0008.659] pm_ids_update: Updating 3,ae, size 256, type 0
[0008.689] pm_ids_update: The pm board id is 3449-0000-200
[0008.696] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0008.703] pm_ids_update: pm id update successful
[0008.733] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0008.739] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0008.747] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0008.753] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0008.761] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e5:42:e7
[0008.768] Plugin Manager: Parse ODM data 0x00084000
[0008.779] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
[0008.798] Find /i2c@7000c000's alias i2c0
[0008.802] get eeprom at 1-a0, size 256, type 0
[0008.811] Find /i2c@7000c500's alias i2c2
[0008.815] get eeprom at 3-a0, size 256, type 0
[0008.819] get eeprom at 3-ae, size 256, type 0
[0008.824] pm_ids_update: Updating 1,a0, size 256, type 0
[0008.829] I2C slave not started
[0008.832] I2C write failed
[0008.835] Writing offset failed
[0008.838] eeprom_init: EEPROM read failed
[0008.842] pm_ids_update: eeprom init failed
[0008.846] pm_ids_update: Updating 3,a0, size 256, type 0
[0008.876] pm_ids_update: The pm board id is 3448-0000-200
[0008.882] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0008.889] pm_ids_update: pm id update successful
[0008.893] pm_ids_update: Updating 3,ae, size 256, type 0
[0008.924] pm_ids_update: The pm board id is 3449-0000-200
[0008.930] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0008.937] pm_ids_update: pm id update successful
[0008.967] Chip UID is 00000001644476451c00000016fe8400
[0008.972] Add serial number:142201903834900084fe as DT property
[0008.980] Applying platform configs
[0008.986] platform-init is not present. Skipping
[0008.991] calling apps_init()
[0009.016] Found 12 GPT partitions in "sd0"
[0009.020] Proceeding to Cold Boot
[0009.023] starting app android_boot_app
[0009.027] Device state: unlocked
[0009.030] display console init
[0009.039] could not find regulator
[0009.062] hdmi cable not connected
[0009.065] is_hdmi_needed: HDMI not connected, returning false
[0009.074] hdmi is not connected
[0009.077] sor0 is not supported
[0009.080] display_console_init: no valid display out_type
[0009.088] subnode volume_up is not found !
[0009.092] subnode back is not found !
[0009.095] subnode volume_down is not found !
[0009.099] subnode menu is not found !
[0009.103] Gpio keyboard init success
[0009.149] found decompressor handler: lz4-legacy
[0009.163] decompressing blob (type 1)...
[0009.197] display_resolution: No display init
[0009.201] Failed to retrieve display resolution
[0009.205] Could not load/initialize BMP blob...ignoring
[0009.258] decompressor handler not found
[0009.262] load_firmware_blob: Firmware blob loaded, entries=2
[0009.268] se_aes_verify_sbk_clear: Error
[0009.272] bl_battery_charging: connected to external power supply
[0009.279] xusb is supported
[0009.285] error while finding nvidia,portmap
[0009.290] could not find regulator
[0009.793] xusb blob version 0 size 126464
[0009.797] firmware size 126464
[0009.802] Firmware timestamp: 0x59fc70d3, Version: 50.20 release
[0009.811] xhci0: 64 bytes context size, 32-bit DMA
[0009.851] usbus0: 5.0Gbps Super Speed USB v3.0
[0009.871] uhub0: <Nvidia XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
[0010.521] uhub0: 9 ports with 9 removable, self powered
[0011.521] failed to get HID devices
[0011.524] failed to init xhci or no usb device attached
[0011.532] display_console_ioctl: No display init
[0011.536] switch_backlight failed
[0011.542] device_query_partition_size: failed to open partition sd0:MSC !
[0011.549] MSC Partition not found
[0011.555] device_query_partition_size: failed to open partition sd0:USP !
[0011.562] USP partition read failed!
[0011.565] blob_init: blob-partition USP header read failed
[0011.571] android_boot Unable to update recovery partition
[0011.576] kfs_getpartname: name = LNX
[0011.580] Loading kernel from LNX
[0011.639] Verifying boot image in OdmNonSecureSBK mode
[0011.682] kernel load address: 0x80080000, size: 476960 bytes
[0011.688] ramdisk load address: 0x84100000, size: 0 bytes
[0011.693] load kernel from storage
[0011.705] decompressor handler not found
[0011.761] Successfully loaded kernel and ramdisk images
[0011.768] display_resolution: No display init
[0011.772] Failed to retrieve display resolution
[0011.776] bmp blob is not loaded and initialized
[0011.781] Failed to display boot-logo
[0011.784] NCK carveout not present
[0011.788] Skipping dts_overrides
[0011.791] NCK carveout not present
[0011.794] shim_invoke: No NCT, Calling dts updates
[0011.805] Find /i2c@7000c000's alias i2c0
[0011.809] get eeprom at 1-a0, size 256, type 0
[0011.818] Find /i2c@7000c500's alias i2c2
[0011.822] get eeprom at 3-a0, size 256, type 0
[0011.826] get eeprom at 3-ae, size 256, type 0
[0011.831] pm_ids_update: Updating 1,a0, size 256, type 0
[0011.836] I2C slave not started
[0011.839] I2C write failed
[0011.842] Writing offset failed
[0011.845] eeprom_init: EEPROM read failed
[0011.849] pm_ids_update: eeprom init failed
[0011.853] pm_ids_update: Updating 3,a0, size 256, type 0
[0011.883] pm_ids_update: The pm board id is 3448-0000-200
[0011.889] Adding plugin-manager/ids/3448-0000-200=/i2c@7000c500:module@0x50
[0011.897] pm_ids_update: pm id update successful
[0011.902] pm_ids_update: Updating 3,ae, size 256, type 0
[0011.932] pm_ids_update: The pm board id is 3449-0000-200
[0011.938] Adding plugin-manager/ids/3449-0000-200=/i2c@7000c500:module@0x57
[0011.946] pm_ids_update: pm id update successful
[0011.976] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0011.982] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0011.990] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0011.996] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0012.004] updating /chosen/nvidia,ethernet-mac node 00:04:4b:e5:42:e7
[0012.010] Plugin Manager: Parse ODM data 0x00084000
[0012.021] shim_cmdline_install: /chosen/bootargs: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
[0012.034] Add serial number:142201903834900084fe as DT property
[0012.044] "bpmp" doesn't exist, creating
[0012.049] Updated bpmp info to DTB
[0012.054] Updated initrd info to DTB
[0012.057] "proc-board" doesn't exist, creating
[0012.063] Updated board info to DTB
[0012.066] "pmu-board" doesn't exist, creating
[0012.072] Updated board info to DTB
[0012.075] "display-board" doesn't exist, creating
[0012.081] Updated board info to DTB
[0012.084] "reset" doesn't exist, creating
[0012.089] Updated reset info to DTB
[0012.092] display_console_ioctl: No display init
[0012.097] display_console_ioctl: No display init
[0012.101] display_console_ioctl: No display init
[0012.106] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000
[0012.140] DTB cmdline: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
[0012.151] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0
[0012.162] Updated bootarg info to DTB
[0012.166] Adding uuid 00000001644476451c00000016fe8400 to DT
[0012.176] device_query_partition_size: failed to open partition sd0:RP6 !
[0012.182] RP6 partition read failed!
[0012.187] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7
[0012.193] Updated memory info to DTB
[0012.198] Updated system-lp0-disable info to DTB
[0012.206] set vdd_core voltage to 1075 mv
[0012.210] setting 'vdd-core' regulator to 1075000 micro volts
[0012.231] could not find regulator
[0012.235] Found secure-pmc; disable BPMP
U-Boot 2016.07-g541e96c (May 31 2019 - 15:44:14 -0700)
TEGRA210
Model: NVIDIA P3450-Porg
Board: NVIDIA P3450-PORG
DRAM: 4 GiB
MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1
Using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
239 bytes read in 110 ms (2 KiB/s)
p3450-porg eMMC boot options
1: primary kernel
Enter choice: 1: primary kernel
Retrieving file: /boot/initrd
0 bytes read in 86 ms (0 Bytes/s)
Retrieving file: /boot/Image
34048008 bytes read in 1527 ms (21.3 MiB/s)
append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 rootfstype=ext4 root=/dev/mmcblk0p1 rw rootwait
## Flattened Device Tree blob at 83100000
Booting using the fdt blob at 0x83100000
reserving fdt memory region: addr=80000000 size=20000
Using Device Tree in place at 0000000083100000, end 0000000083173e9a
Starting kernel ...
<hit enter to activate fiq debugger>
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.140-tegra (buildbrain@mobile-u64-3531) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP PREEMPT Wed Mar 13 00:32:22 PDT 2019
[ 0.000000] Boot CPU: AArch64 Processor [411fd071]
[ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 48,
[ 0.000000] OF: fdt: - 80000000 , 7ee00000
[ 0.000000] OF: fdt: - 100000000 , 7f200000
[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB
[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb0_carveout': base 0x0000000000000000, size 0 MiB
[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB
[ 0.000000] OF: fdt:Reserved memory: failed to reserve memory for node 'fb1_carveout': base 0x0000000000000000, size 0 MiB
[ 0.000000] OF: reserved mem: initialized node vpr-carveout, compatible id nvidia,vpr-carveout
[ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id nvidia,iram-carveout
[ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible id nvidia,ramoops
[ 0.000000] cma: Reserved 64 MiB at 0x00000000fac00000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] percpu: Embedded 23 pages/cpu @ffffffc0fefd2000 s53400 r8192 d32616 u94208
[ 0.000000] CPU features: enabling workaround for ARM erratum 832075
[ 0.000000] Speculative Store Bypass Disable mitigation not required
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1023544
[ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 console=ttyS0,115200n8 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff780000 core_edp_mv=1075 core_edp_ma=4000 root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 root=/dev/mmcblk0p1 rw rootwait console=ttyS0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0 rootfstype=ext4 root=/dev/mmcblk0p1 rw rootwait
[ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes
[ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes
[ 0.000000] log_buf_len min size: 32768 bytes
[ 0.000000] log_buf_len: 131072 bytes
[ 0.000000] early log buf free: 29492(90%)
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Memory: 3576064K/4159488K available (15166K kernel code, 2914K rwdata, 6616K rodata, 8512K init, 605K bss, 108288K reserved, 475136K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
[ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008f50000 ( 15168 KB)
[ 0.000000] .rodata : 0xffffff8008f50000 - 0xffffff80095d0000 ( 6656 KB)
[ 0.000000] .init : 0xffffff80095d0000 - 0xffffff8009e20000 ( 8512 KB)
[ 0.000000] .data : 0xffffff8009e20000 - 0xffffff800a0f8808 ( 2915 KB)
[ 0.000000] .bss : 0xffffff800a0f8808 - 0xffffff800a18fe3c ( 606 KB)
[ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB)
[ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
[ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
[ 0.000000] 0xffffffbf00000000 - 0xffffffbf03fc8000 ( 63 MB actual)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc0ff200000 ( 4082 MB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller
[ 0.000000] t210 clock and reset probe
[ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.001483] Console: colour dummy device 80x25
[ 0.002335] console [tty0] enabled
[ 0.002359] kmemleak: Kernel memory leak detector disabled
[ 0.002389] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800)
[ 0.002416] pid_max: default: 32768 minimum: 301
[ 0.002872] Security Framework initialized
[ 0.003103] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.003123] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.004318] ftrace: allocating 46802 entries in 183 pages
[ 0.175161] ASID allocator initialised with 65536 entries
[ 0.211461] tegra-id: chipid=22117.
[ 0.211504] tegra-id: opt_subrevision=0.
[ 0.211533] Tegra Speedo/IDDQ fuse revision 4
[ 0.211548] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2
[ 0.211563] Tegra: CPU Process ID 0, SoC Process ID 1, GPU Process ID 0
[ 0.211580] Tegra: CPU Speedo Value 2081, SoC Speedo Value 1976, GPU Speedo Value 2085
[ 0.211600] Tegra: CPU IDDQ Value 1940, SoC IDDQ Value 2152, GPU IDDQ Value 2610
[ 0.211635] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 1
[ 0.211662] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-a02.dts
[ 0.211695] DTB Build time: Mar 15 2019 09:52:07
[ 0.261043] CPU1: Booted secondary processor [411fd071]
[ 0.292941] CPU2: Booted secondary processor [411fd071]
[ 0.324949] CPU3: Booted secondary processor [411fd071]
[ 0.325040] Brought up 4 CPUs
[ 0.325102] SMP: Total of 4 processors activated.
[ 0.325119] CPU features: detected feature: 32-bit EL0 Support
[ 0.325396] CPU: All CPU(s) started at EL2
[ 0.325426] alternatives: patching kernel code
[ 0.333413] devtmpfs: initialized
[ 0.366879] Initilizing CustomIPI irq domain
[ 0.367288] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.367332] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.377836] pinctrl core: initialized pinctrl subsystem
[ 0.378466] OS set in device tree is not L4T.
[ 0.378871] regulator-dummy: no parameters
[ 0.379158] Initializing plugin-manager
[ 0.379306] Plugin module not found
[ 0.379523] node /plugin-manager/fragement@0 match with board >=3448-0000-100
[ 0.380065] node /plugin-manager/fragment@1 match with board >=3448-0000-101
[ 0.380836] node /plugin-manager/fragment@5 match with board 3449-0000-200
[ 0.384044] NET: Registered protocol family 16
[ 0.385396] pstore: using zlib compression
[ 0.386033] console [pstore-1] enabled
[ 0.386050] pstore: Registered ramoops as persistent store backend
[ 0.386068] ramoops: attached 0x200000@0xb0000000, ecc: 0/0
[ 0.401062] cpuidle: using governor menu
[ 0.404822] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver
[ 0.406289] vdso: 2 pages (1 code @ ffffff8008f57000, 1 data @ ffffff8009e24000)
[ 0.406335] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.409470] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atomic allocations
[ 0.410998] tegra_bpmp_of_clk_init: EMC proxy not found.
[ 0.411940] tegra_powergate_init: DONE
[ 0.411978] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-a02.dts
[ 0.412016] DTB Build time: Mar 15 2019 09:52:07
[ 0.413703] Tegra reboot handler registered.
[ 0.418042] iommu: Adding device tegra-carveouts to group 0
[ 0.418212] platform tegra-carveouts: domain=ffffffc0f9bf0318 allocates as[0]=ffffffc0f9bd40a8
[ 0.418581] iommu: Adding device smmu_test to group 1
[ 0.418645] platform smmu_test: domain=ffffffc0f9bf0558 allocates as[0]=ffffffc0f9bd4110
[ 0.419481] mc: mapped MMIO address: 0xffffff800802e000 -> 0x70019000
[ 0.419556] mc: mapped MMIO address: 0xffffff8008065000 -> 0x7001c000
[ 0.419627] mc: mapped MMIO address: 0xffffff8008079000 -> 0x7001d000
[ 0.419651] nv-tegra-mc 70019000.mc: No mssnvlink node
[ 0.419687] mc-err: mcerr ops are set to t21x
[ 0.429303] iommu: Adding device 70090000.xusb to group 2
[ 0.429615] iommu: Adding device 70006000.serial to group 3
[ 0.429717] platform 70006000.serial: domain=ffffffc0f947c618 allocates as[0]=ffffffc0f9bd4178
[ 0.430151] iommu: Adding device 70006040.serial to group 4
[ 0.430439] iommu: Adding device 70006200.serial to group 5
[ 0.430683] iommu: Adding device sound to group 6
[ 0.430744] platform sound: domain=ffffffc0f947cb58 allocates as[0]=ffffffc0f9bd41e0
[ 0.431316] iommu: Adding device 7000d400.spi to group 7
[ 0.431589] iommu: Adding device 7000d600.spi to group 8
[ 0.431879] iommu: Adding device 70410000.spi to group 9
[ 0.432198] iommu: Adding device 50000000.host1x to group 10
[ 0.432493] iommu: Adding device 54080000.vi to group 11
[ 0.432904] iommu: Adding device 54600000.isp to group 12
[ 0.433250] iommu: Adding device 54680000.isp to group 13
[ 0.433590] iommu: Adding device tegradc.0 to group 14
[ 0.433662] platform tegradc.0: domain=ffffffc0f9489a98 allocates as[0]=ffffffc0f9bd4248
[ 0.434200] platform tegradc.0: IOVA linear map 0x00000000d7000000(19000000)
[ 0.434533] iommu: Adding device tegradc.1 to group 15
[ 0.434600] platform tegradc.1: domain=ffffffc0f9489cd8 allocates as[0]=ffffffc0f9bd42b0
[ 0.435127] platform tegradc.1: IOVA linear map 0x00000000d7000000(19000000)
[ 0.435380] iommu: Adding device 54340000.vic to group 16
[ 0.435609] iommu: Adding device 544c0000.nvenc to group 17
[ 0.435826] iommu: Adding device 54500000.tsec to group 18
[ 0.436041] iommu: Adding device 54100000.tsecb to group 19
[ 0.436252] iommu: Adding device 54480000.nvdec to group 20
[ 0.436491] iommu: Adding device 54380000.nvjpg to group 21
[ 0.437619] iommu: Adding device 546c0000.i2c to group 22
[ 0.437969] iommu: Adding device 57000000.gpu to group 23
[ 0.438032] platform 57000000.gpu: domain=ffffffc0f9494cd8 allocates as[0]=ffffffc0f9bd4318
[ 0.438089] platform 57000000.gpu: domain=ffffffc0f9494cd8 allocates as[1]=ffffffc0f9bd4380
[ 0.438149] platform 57000000.gpu: domain=ffffffc0f9494cd8 allocates as[2]=ffffffc0f9bd43e8
[ 0.438208] platform 57000000.gpu: domain=ffffffc0f9494cd8 allocates as[3]=ffffffc0f9bd4450
[ 0.439079] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled.
[ 0.439121] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present
[ 0.439148] tegra-pmc: ### PMC reset source: TEGRA_POWER_ON_RESET
[ 0.439168] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM
[ 0.439185] tegra-pmc: ### PMC reset status reg: 0x0
[ 0.489119] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered
[ 0.489155] tegra-pmc: Clear bootloader IO dpd settings
[ 0.489188] tegra-pmc 7000e400.pmc: IO padctrl driver initialized
[ 0.489270] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reset commands
[ 0.489583] iommu: Adding device 70012000.se to group 24
[ 0.490441] iommu: Adding device 7000c000.i2c to group 25
[ 0.490706] iommu: Adding device 7000c400.i2c to group 26
[ 0.491028] iommu: Adding device 7000c500.i2c to group 27
[ 0.491351] iommu: Adding device 7000c700.i2c to group 28
[ 0.491719] iommu: Adding device 7000d000.i2c to group 29
[ 0.492036] iommu: Adding device 7000d100.i2c to group 30
[ 0.492398] iommu: Adding device sdhci-tegra.0 to group 31
[ 0.492468] platform sdhci-tegra.0: domain=ffffffc0f9524e58 allocates as[0]=ffffffc0f9bd44b8
[ 0.493423] iommu: Adding device 700d0000.xudc to group 32
[ 0.499130] vdd-ac-bat: 5000 mV
[ 0.499555] vdd-5v0-sys: 5000 mV
[ 0.500663] vdd-5v0-hdmi: supplied by vdd-5v0-sys
[ 0.500750] vdd-5v0-hdmi: 5000 mV
[ 0.501256] vdd-1v8: 1800 mV
[ 0.501684] vdd-fan: supplied by vdd-5v0-sys
[ 0.501737] vdd-fan: 5000 mV
[ 0.502200] vdd-usb-vbus: supplied by vdd-5v0-sys
[ 0.502274] vdd-usb-vbus: 5000 mV
[ 0.502863] vdd-usb-vbus2: 5000 mV
[ 0.534096] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.536623] GPIO line 151 (camera-control-output-low) hogged as output/low
[ 0.537022] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochip0 (tegra-gpio)
[ 0.545528] eventlib_kernel: keventlib is initialized, test id: 0
[ 0.545904] SCSI subsystem initialized
[ 0.546434] usbcore: registered new interface driver usbfs
[ 0.546508] usbcore: registered new interface driver hub
[ 0.546591] usbcore: registered new device driver usb
[ 0.550675] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8
[ 0.552242] random: fast init done
[ 0.556448] vdd-core: 600 <--> 1162 mV at 1075 mV
[ 0.557755] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV
[ 0.560231] vdd-ddr-1v1: 1150 mV
[ 0.564225] vdd-pre-reg-1v35: 1350 mV
[ 0.568322] vdd-1v8: 1800 mV
[ 0.568596] vdd-1v8: Failed to create debugfs directory
[ 0.572228] avdd-sys-1v2: 1200 mV
[ 0.576229] vdd-pex-1v0: 1050 mV
[ 0.577029] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV
[ 0.577698] max77620-ldo3: at 3100 mV
[ 0.580233] vdd-rtc: 850 <--> 1100 mV at 1000 mV
[ 0.580865] max77620-ldo5: at 3100 mV
[ 0.581509] max77620-ldo6: at 2800 mV
[ 0.584234] avdd-1v05-pll: 1050 mV
[ 0.588227] avdd-io-hdmi-dp: 1050 mV
[ 0.589785] GPIO line 505 (spmic-default-output-high) hogged as output/high
[ 0.590100] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpiochip1 (max77620-gpio)
[ 0.592251] max77620 4-003c: max77620 probe successful
[ 0.594507] i2c i2c-6: Unbalanced pm_runtime_enable!
[ 0.595055] media: Linux media interface: v0.10
[ 0.595117] Linux video capture interface: v2.00
[ 0.596045] pps_core: LinuxPPS API ver. 1 registered
[ 0.596073] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.596114] PTP clock support registered
[ 0.599529] tegra_fiq_debugger_init: found FIQ source (IRQ 98)
[ 0.605774] tegra210-emc 7001b000.external-memory-controller: validated EMC DFS table
[ 0.606587] Advanced Linux Sound Architecture Driver Initialized.
[ 0.607243] Bluetooth: Core ver 2.22
[ 0.607312] NET: Registered protocol family 31
[ 0.607330] Bluetooth: HCI device and connection manager initialized
[ 0.607362] Bluetooth: HCI socket layer initialized
[ 0.607384] Bluetooth: L2CAP socket layer initialized
[ 0.607423] Bluetooth: SCO socket layer initialized
[ 0.609135] tegra210_dvfs: no clock found for sdmmc2_ddr
[ 0.609177] tegra210_dvfs: no clock found for sdmmc4_ddr
[ 0.609235] tegra210_dvfs: no clock found for sdmmc1_ddr
[ 0.609262] tegra210_dvfs: no clock found for sdmmc3_ddr
[ 0.611950] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering probe
[ 0.613352] vdd-3v3-sys: supplied by vdd-5v0-sys
[ 0.613455] vdd-3v3-sys: 3300 mV
[ 0.613740] vdd-1v8: supplied by vdd-3v3-sys
[ 0.617262] vdd-usb-vbus2: supplied by vdd-3v3-sys
[ 0.617741] vdd-3v3-sd: supplied by vdd-3v3-sys
[ 0.617820] vdd-3v3-sd: 3300 mV
[ 0.619065] avdd-io-edp-1v05: supplied by avdd-1v05-pll
[ 0.619122] avdd-io-edp-1v05: 1050 mV
[ 0.619605] vdd-usb-hub-en: supplied by vdd-1v8
[ 0.619652] vdd-usb-hub-en: 5000 mV
[ 0.620984] camchar: rtcpu character device driver loaded
[ 0.621736] extcon-gpio-states extcon:extcon@1: Cable state:0, cable id:0
[ 0.623070] clocksource: Switched to clocksource arch_sys_counter
[ 0.662237] VFS: Disk quotas dquot_6.6.0
[ 0.662398] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.662892] nvmap_heap_init: nvmap_heap_init: created heap block cache
[ 0.663379] dma_declare_coherent_resizable_cma_memory:324: resizable heap=vpr, base=0x00000000d7000000, size=0x19000000
[ 0.663429] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (13) rem_chunk_size(0x1000000)
[ 0.663665] cma: enabled page replacement for spfn=d7000, epfn=f0000
[ 0.663690] dma_declare_coherent_resizable_cma_memory:373: resizable cma heap=vpr create successful
[ 0.663715] tegra-carveouts tegra-carveouts: assigned reserved memory node vpr-carveout
[ 0.663767] tegra-carveouts tegra-carveouts: iram :dma coherent mem declare 0x0000000040001000,258048
[ 0.663792] tegra-carveouts tegra-carveouts: assigned reserved memory node iram-carveout
[ 0.663824] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways
[ 0.663846] nvmap_page_pool_init: Total RAM pages: 1012800
[ 0.663863] nvmap_page_pool_init: nvmap page pool size: 126600 pages (494 MB)
[ 0.664034] nvmap_background_zero_thread: PP zeroing thread starting.
[ 0.664342] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB)
[ 0.665313] misc nvmap: created heap vpr base 0x00000000d7000000 size (409600KiB)
[ 0.673495] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm
[ 0.673893] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm
[ 0.674153] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm
[ 0.674379] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm
[ 0.674579] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die
[ 0.674864] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz
[ 0.674883] pre_t19x_iso_plat_init(): max_iso_bw=33280000KB
[ 0.675367] NET: Registered protocol family 2
[ 0.676343] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.676574] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.677085] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.677258] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.677358] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.677779] NET: Registered protocol family 1
[ 0.678555] RPC: Registered named UNIX socket transport module.
[ 0.678583] RPC: Registered udp transport module.
[ 0.678600] RPC: Registered tcp transport module.
[ 0.678617] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.678872] Trying to unpack rootfs image as initramfs...
[ 0.688371] host1x 50000000.host1x: initialized
[ 0.690213] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 0.693335] audit: initializing netlink subsys (disabled)
[ 0.693426] audit: type=2000 audit(0.543:1): initialized
[ 0.694184] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[ 0.704328] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.705830] ntfs: driver 2.1.32 [Flags: R/W].
[ 0.706634] 9p: Installing v9fs 9p2000 file system support
[ 0.709914] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240)
[ 0.710071] io scheduler noop registered
[ 0.710376] io scheduler cfq registered (default)
[ 0.713101] gic 702f9000.agic: GIC IRQ controller registered
[ 0.716120] iommu: Adding device 702ef000.adsp to group 33
[ 0.722835] iommu: Adding device aconnect@702c0000:adsp_audio to group 34
[ 0.723012] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered
[ 0.724163] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 = 0x928a412
[ 0.724196] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT_0 = 0x4
[ 0.725828] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane = usb2-0, function = xusb
[ 0.725970] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane = usb2-1, function = xusb
[ 0.726083] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane = usb2-2, function = xusb
[ 0.726289] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane = pcie-0, function = pcie-x1
[ 0.726401] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane = pcie-1, function = pcie-x4
[ 0.726513] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane = pcie-2, function = pcie-x4
[ 0.726622] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane = pcie-3, function = pcie-x4
[ 0.726729] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane = pcie-4, function = pcie-x4
[ 0.726834] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane = pcie-5, function = xusb
[ 0.726939] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane = pcie-6, function = xusb
[ 0.733304] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops
[ 0.734638] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000
[ 0.736523] tegra-pcie 1003000.pcie-controller: 4x1, 1x1 configuration
[ 0.737804] tegra-pcie 1003000.pcie-controller: PCIE: Enable power rails
[ 0.738172] tegra-pcie 1003000.pcie-controller: probing port 0, using 4 lanes
[ 0.739413] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:camera_platform_driver probe
[ 0.739653] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=1500000, vi_iso_bw=750000, max_bw=1500000
[ 0.739907] Adding domain tsec-pd to PM domain host1x-pd
[ 0.741941] tegra-pcie 1003000.pcie-controller: probing port 1, using 1 lanes
[ 0.742778] tsec 54500000.tsec: initialized
[ 0.744481] tsec 54100000.tsecb: initialized
[ 0.745218] Adding domain nvdec-pd to PM domain host1x-pd
[ 0.748379] nvdec 54480000.nvdec: initialized
[ 0.749498] Adding domain vic03-pd to PM domain host1x-pd
[ 0.749705] Adding domain msenc-pd to PM domain host1x-pd
[ 0.749880] Adding domain nvjpg-pd to PM domain host1x-pd
[ 0.753741] falcon 54340000.vic: initialized
[ 0.755025] falcon 544c0000.nvenc: initialized
[ 0.756455] falcon 54380000.nvjpg: initialized
[ 0.761016] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1
[ 0.761143] display board info: id 0x0, fab 0x0
[ 0.761215] generic_infoframe_type: 0x87
[ 0.761353] tegradc tegradc.0: DT parsed successfully
[ 0.761413] tegradc tegradc.0: Display dc.ffffff800ab40000 registered with id=0
[ 0.764893] tegradc tegradc.0: probed
[ 0.768965] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels
[ 0.773723] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 10 channels
[ 0.774655] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initialized
[ 0.775019] kfuse 7000fc00.kfuse: initialized
[ 0.776498] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-supply not available
[ 0.777602] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0
[ 0.778974] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now
[ 0.779018] vdd-cpu: 708 <--> 1322 mV at 708 mV
[ 0.779575] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator registration passed
[ 0.781368] vdd-gpu: applied init 1000000uV constraint
[ 0.781398] vdd-gpu: 708 <--> 1323 mV at 997 mV
[ 0.781831] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator registration passed
[ 0.786440] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.786630] No Device Node present for smmu client: serial8250 !!
[ 0.786661] platform serial8250: No iommus property found in DT node, got swgids from fixup(101004000)
[ 0.786752] iommu: Adding device serial8250 to group 35
[ 0.790308] console [ttyS0] disabled
[ 0.790470] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud = 25500000) is a Tegra
[ 1.264502] tegra-pcie 1003000.pcie-controller: link 0 down, retrying
[ 1.668848] tegra-pcie 1003000.pcie-controller: link 0 down, retrying
[ 2.084915] tegra-pcie 1003000.pcie-controller: link 0 down, retrying
[ 2.086933] tegra-pcie 1003000.pcie-controller: link 0 down, ignoring
[ 2.087327] tegra-pcie 1003000.pcie-controller: PCI host bridge to bus 0000:00
[ 2.087337] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 2.087342] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff]
[ 2.087347] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref]
[ 2.087353] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 2.087769] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 2.099253] pci 0000:00:02.0: BAR 14: assigned [mem 0x13000000-0x130fffff]
[ 2.099259] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff]
[ 2.099269] pci 0000:01:00.0: BAR 4: assigned [mem 0x13000000-0x13003fff 64bit]
[ 2.099295] pci 0000:01:00.0: BAR 2: assigned [mem 0x13004000-0x13004fff 64bit]
[ 2.099318] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff]
[ 2.099329] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 2.099335] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff]
[ 2.099343] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff]
[ 2.100139] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt
[ 2.100145] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[ 3.138631] console [ttyS0] enabled
[ 3.139005] Console: switching to colour frame buffer device 80x30
[ 3.143869] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baud = 0) is a TEGRA_UART
[ 3.144191] serial-tegra 70006200.serial: RX in PIO mode
[ 3.144285] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baud = 0) is a TEGRA_UART
[ 3.145206] [drm] Initialized
[ 3.175356] tegradc tegradc.0: fb registered
[ 3.177074] brd: module loaded
[ 3.184522] tegradc tegradc.1: disp1 connected to head1->/host1x/sor
[ 3.187313] loop: module loaded
[ 3.187410] tegra_profiler: version: 1.132, samples/io: 46/26
[ 3.187541] tegra_profiler: auth: init
[ 3.188721] THERMAL EST: found 2 subdevs
[ 3.188726] THERMAL EST num_resources: 0
[ 3.188732] [THERMAL EST subdev 0]
[ 3.188739] [THERMAL EST subdev 1]
[ 3.189174] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type thermal-fan-est
[ 3.189179] THERMAL EST: thz register success.
[ 3.189328] THERMAL EST: end of probe, return err: 0
[ 3.190587] hisi_sas: driver version v1.6
[ 3.194604] tegra-qspi 70410000.spi: Prod settings list not found
[ 3.195856] qspi_mtd spi32766.0: MX25U3235F (4096 Kbytes)
[ 3.195863] qspi_mtd spi32766.0: mtd .name = spi32766.0, .size = 0x400000 (4MiB) .erasesize = 0x00001000 (4KiB) .numeraseregions = 0
[ 3.198941] libphy: Fixed MDIO Bus: probed
[ 3.199971] tun: Universal TUN/TAP device driver, 1.6
[ 3.199975] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 3.201120] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 3.201123] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 3.201179] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
[ 3.201181] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 3.201229] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
[ 3.201231] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[ 3.201281] Intel(R) 10GbE PCI Express Linux Network Driver - version 4.6.4
[ 3.201284] Copyright(c) 1999 - 2017 Intel Corporation.
[ 3.202144] r8168 0000:01:00.0: enabling device (0000 -> 0003)
[ 3.202175] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded
[ 3.216343] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Invalid ethernet address 00:00:00:00:00:00, trying device tree node
[ 3.216476] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Found valid ethernet address 00:04:4b:e5:42:e7 from device tree
[ 3.217090] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625.
[ 3.217130] r8168 Copyright (C) 2017 Realtek NIC software team <nicfae@realtek.com>
[ 3.217130] This program comes with ABSOLUTELY NO WARRANTY; for details, please see <http://www.gnu.org/licenses/>.
[ 3.217130] This is free software, and you are welcome to redistribute it under certain conditions; see <http://www.gnu.org/licenses/>.
[ 3.217744] PPP generic driver version 2.4.2
[ 3.217947] PPP BSD Compression module registered
[ 3.217952] PPP Deflate Compression module registered
[ 3.217993] PPP MPPE Compression module registered
[ 3.218000] NET: Registered protocol family 24
[ 3.218075] usbcore: registered new interface driver r8152
[ 3.218123] usbcore: registered new interface driver asix
[ 3.218185] usbcore: registered new interface driver ax88179_178a
[ 3.218239] usbcore: registered new interface driver cdc_ether
[ 3.218276] usbcore: registered new interface driver net1080
[ 3.218317] usbcore: registered new interface driver cdc_subset
[ 3.218356] usbcore: registered new interface driver zaurus
[ 3.218407] usbcore: registered new interface driver cdc_ncm
[ 3.218577] VFIO - User Level meta-driver version: 0.3
[ 3.219880] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.219902] ehci-pci: EHCI PCI platform driver
[ 3.219948] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.219959] ohci-pci: OHCI PCI platform driver
[ 3.220001] ohci-platform: OHCI generic platform driver
[ 3.222682] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP
[ 3.223689] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0
[ 3.224873] tegra-xusb 70090000.xusb: extcon 0: ffffffc0f9188800 id
[ 3.224984] tegra-xusb 70090000.xusb: Direct firmware load for tegra21x_xusb_firmware failed with error -2
[ 3.224987] tegra-xusb 70090000.xusb: Falling back to user helper
[ 3.226298] usbcore: registered new interface driver uas
[ 3.226359] usbcore: registered new interface driver usb-storage
[ 3.226469] usbcore: registered new interface driver usbserial
[ 3.229618] tegra-xudc-new 700d0000.xudc: device count: 1
[ 3.230943] tegra-xudc-new 700d0000.xudc: USB charger detection disabled
[ 3.230956] tegra-xudc-new 700d0000.xudc: vbus state: 0
[ 3.230989] tegra-xudc-new 700d0000.xudc: entering ELPG
[ 3.231269] tegra-xudc-new 700d0000.xudc: entering ELPG done
[ 3.231977] mousedev: PS/2 mouse device common for all mice
[ 3.232066] usbcore: registered new interface driver xpad
[ 3.361265] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0
[ 3.363966] rtc rtc1: alarm rtc device
[ 3.363984] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1
[ 3.364010] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock
[ 3.364571] i2c /dev entries driver
[ 3.366234] imx219 6-0010: tegracam sensor driver:imx219_v2.0.6
[ 3.389561] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10
[ 3.389630] imx219 6-0010: imx219_board_setup: error during i2c read probe (-121)
[ 3.389660] imx219 6-0010: board setup failed
[ 3.389758] imx219: probe of 6-0010 failed with error -121
[ 3.391121] max77620-power max77620-power: Event recorder REG_NVERC : 0x0
[ 3.394130] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2
[ 3.394134] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4
[ 3.394551] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 3.394568] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when cpu reaches 102500 mC
[ 3.394577] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when cpu reaches 100500 mC
[ 3.394738] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 3.394747] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when gpu reaches 103000 mC
[ 3.394753] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when gpu reaches 101000 mC
[ 3.394894] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 3.394903] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down when pll reaches 127000 mC
[ 3.394907] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot temperature
[ 3.395117] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19
[ 3.395917] tegra_aotag tegra-aotag: Registering sensor 0
[ 3.395972] tegra_aotag tegra-aotag: Invalid temp readout
[ 3.395997] tegra_aotag tegra-aotag: Invalid temp readout
[ 3.396013] tegra_aotag tegra-aotag: Bound to TZ : ID 0
[ 3.396022] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0
[ 3.396946] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 3.396964] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device' registered
[ 3.397154] tegra_aotag tegra-aotag: Invalid temp readout
[ 3.397183] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling device' registered
[ 3.397626] parse_throttle_dt_data: Num cap clks = 6
[ 3.397632] parse_throttle_dt_data: clk=cclk_g type=2
[ 3.397646] parse_throttle_dt_data: clk=gpu type=4
[ 3.397674] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0
[ 3.397693] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0
[ 3.397714] parse_throttle_dt_data: clk=cap.throttle.sclk type=0
[ 3.397717] parse_throttle_dt_data: clk=emc type=3
[ 3.398179] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 3.398289] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 3.398445] tegra_throttle_probe: probe successful. #cdevs=4
[ 3.399322] FAN dev name: pwm-fan
[ 3.399377] FAN:gpio request success.
[ 3.399456] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255
[ 3.399756] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal
[ 3.399945] pwm_fan_driver pwm-fan: fan tach request irq success
[ 3.399954] pwm_fan_driver pwm-fan: tach period: 1000
[ 3.400036] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2
[ 3.400040] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2
[ 3.400044] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2
[ 3.400047] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2
[ 3.400051] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3
[ 3.400054] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3
[ 3.400057] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3
[ 3.400061] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4
[ 3.400064] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4
[ 3.400068] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4
[ 3.400710] tegra-wdt 60005100.watchdog: Tegra WDT enabled on probe. Timeout = 120 seconds.
[ 3.401063] tegra-wdt 60005100.watchdog: initialized (timeout = 120 sec, nowayout = 1)
[ 3.401975] device-mapper: uevent: version 1.0.3
[ 3.402497] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
[ 3.407754] tegra210-cpufreq cpufreq: probe()...completed
[ 3.408604] sdhci: Secure Digital Host Controller Interface driver
[ 3.408606] sdhci: Copyright(c) Pierre Ossman
[ 3.408607] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.409102] sdhci-tegra sdhci-tegra.0: Got CD GPIO
[ 3.409451] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful
[ 3.409574] sdhci-tegra sdhci-tegra.0: wakeup init done, cdirq 300
[ 3.413087] tegra-se 70012000.se: tegra_se_probe: complete
[ 3.413614] hidraw: raw HID events driver (C) Jiri Kosina
[ 3.414707] usbcore: registered new interface driver usbhid
[ 3.414708] usbhid: USB HID core driver
[ 3.416897] tegra21x_actmon 6000c800.actmon: in actmon_register()...
[ 3.417074] tegra21x_actmon 6000c800.actmon: initialization Completed for the device mc_all
[ 3.418837] nvpmodel: initialized successfully
[ 3.419956] usbcore: registered new interface driver snd-usb-audio
[ 3.420015] No Device Node present for smmu client: snd-soc-dummy !!
[ 3.420019] platform snd-soc-dummy: No iommus property found in DT node, got swgids from fixup(101004000)
[ 3.420037] iommu: Adding device snd-soc-dummy to group 36
[ 3.427542] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/card0/input0
[ 3.452167] OPE platform probe
[ 3.452255] OPE platform probe successful
[ 3.452638] OPE platform probe
[ 3.452723] OPE platform probe successful
[ 3.463286] mmc0: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA 64-bit with 64 bit addr
[ 3.477719] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok
[ 3.477851] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok
[ 3.477974] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok
[ 3.478100] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok
[ 3.478224] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok
[ 3.478347] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok
[ 3.478472] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok
[ 3.478593] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok
[ 3.478718] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok
[ 3.478843] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok
[ 3.491555] u32 classifier
[ 3.491556] Actions configured
[ 3.491626] Initializing XFRM netlink socket
[ 3.492363] NET: Registered protocol family 10
[ 3.493119] NET: Registered protocol family 17
[ 3.493129] NET: Registered protocol family 15
[ 3.493203] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 3.493251] Bluetooth: RFCOMM socket layer initialized
[ 3.493259] Bluetooth: RFCOMM ver 1.11
[ 3.493264] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.493268] Bluetooth: HIDP socket layer initialized
[ 3.493285] 9pnet: Installing 9P2000 support
[ 3.493319] Key type dns_resolver registered
[ 3.499276] Registered cp15_barrier emulation handler
[ 3.499330] Registered setend emulation handler
[ 3.500399] registered taskstats version 1
[ 3.500989] Adding domain ve2-pd to PM domain host1x-pd
[ 3.501230] Adding domain ve-pd to PM domain host1x-pd
[ 3.788544] mmc0: hw tuning done ...
[ 3.788575] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 3.788898] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 3.793649] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12
[ 4.328089] tegradc tegradc.1: No lt-data, using default setting
[ 4.334106] tegradc tegradc.1: No hpd-gpio in DT
[ 4.338741] tegradc tegradc.1: DT parsed successfully
[ 4.343815] tegradc tegradc.1: Display dc.ffffff800f4c0000 registered with id=1
[ 4.351865] tegradc tegradc.1: dpd enable lookup fail:-19
[ 4.862861] Host read timeout at address 545c00c4
[ 4.864398] tegradc tegradc.1: probed
[ 4.878823] tegradc tegradc.1: fb registered
[ 4.886231] hpd: state 7 (Takeover from bootloader), hpd 0, pending_hpd_evt 1
[ 4.893366] hpd: switching from state 7 (Takeover from bootloader) to state 0 (Reset)
[ 4.896255] isp 54600000.isp: initialized
[ 4.897037] isp 54680000.isp: initialized
[ 4.908643] clk_cbus_recalc_rate: no gbus parent
[ 4.908648] clk_cbus_round_rate: no gbus parent
[ 4.908649] clk_cbus_round_rate: no gbus parent
[ 4.908654] clk_cbus_recalc_rate: no gbus parent
[ 4.908744] clk_cbus_recalc_rate: no gbus parent
[ 4.908747] clk_cbus_round_rate: no gbus parent
[ 4.908748] clk_cbus_round_rate: no gbus parent
[ 4.908751] clk_cbus_recalc_rate: no gbus parent
[ 4.908764] tegra_dvfs: GPU-cap: registered
[ 4.908821] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200uV, scaling enabled
[ 4.908823] tegra dvfs: vdd-core: nominal 1075mV, offset 600000uV, step 12500uV, scaling enabled
[ 4.908824] tegra dvfs: vdd-gpu: nominal 1058mV, offset 708000uV, step 10000uV, scaling enabled
[ 4.959138] tegra_dvfs: vdd-gpu-vts: registered
[ 4.981008] hpd: state 0 (Reset), hpd 0, pending_hpd_evt 0
[ 4.986510] tegradc tegradc.1: blank - powerdown
[ 4.991139] extcon-disp-state extcon:disp-state: cable 44 state 0 already set.
[ 4.991199] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cooling device' registered
[ 4.991832] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap cooling device' registered
[ 4.992424] input: gpio-keys as /devices/gpio-keys/input/input1
[ 5.022408] Extcon DP: HPD disabled
[ 5.025897] hpd: hpd_switch 0
[ 5.028865] hpd: switching from state 0 (Reset) to state 1 (Check Plug)
[ 5.035479] hpd: state 1 (Check Plug), hpd 0, pending_hpd_evt 0
[ 5.041397] hpd: switching from state 1 (Check Plug) to state 3 (Disabled)
[ 5.049042] tegra_rtc 7000e000.rtc: setting system clock to 2000-01-01 01:00:26 UTC (946688426)
[ 5.058707] vi 54080000.vi: vi_probe: ++
[ 5.066112] vi 54080000.vi: initialized
[ 5.072270] vi 54080000.vi: subdev nvcsi--1 bound
[ 5.077217] mmcblk mmc0:aaaa: Card claimed for testing.
[ 5.083587] Disable partitions left on by BL
[ 5.087862] disb
[ 5.089913] bwmgr: missing cdev-type property
[ 5.094395] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -2147483647 forced to -127000
[ 5.103744] DRAM derating cdev registered.
[ 5.108864] vdd-1v8: disabling
[ 5.111925] vdd-fan: disabling
[ 5.114971] vdd-usb-vbus: disabling
[ 5.118465] vdd-usb-vbus2: disabling
[ 5.122049] avdd-io-edp-1v05: disabling
[ 5.125949] vdd-usb-hub-en: disabling
[ 5.129833] ALSA device list:
[ 5.132813] #0: tegra-hda at 0x70038000 irq 83
[ 5.137429] #1: tegra-snd-t210ref-mobile-rt565x
[ 5.176987] EXT4-fs (mmcblk0p1): recovery complete
[ 5.181796] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[ 5.189901] VFS: Mounted root (ext4 filesystem) on device 179:1.
[ 5.202174] devtmpfs: mounted
[ 5.208201] Freeing unused kernel memory: 8512K
[ 5.400729] systemd[1]: System time before build time, advancing clock.
[ 5.435172] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 5.452646] cgroup: cgroup2: unknown option "nsdelegate"
[ 5.474880] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 5.496968] systemd[1]: Detected architecture arm64.
[ 5.526009] systemd[1]: Set hostname to <jetson-nano>.
[ 5.610742] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
[ 5.627877] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[ 5.785213] random: systemd: uninitialized urandom read (16 bytes read)
[ 5.791891] systemd[1]: Reached target User and Group Name Lookups.
[ 5.798472] random: systemd: uninitialized urandom read (16 bytes read)
[ 5.806793] systemd[1]: Created slice User and Session Slice.
[ 5.812705] random: systemd: uninitialized urandom read (16 bytes read)
[ 5.819462] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 5.829185] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 5.839552] systemd[1]: Created slice System Slice.
[ 5.910895] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)