We are flashing devices with Jetson Orin NX 8GB modules. Even though we use the same process, on some devices we observe that they do not boot properly after flashing. Booting fails with the following message in the MB2 step: I> Task: Partition Manager Init I> strt_pg_num(1) num_of_pgs(1) read_buf(0x273801000) I> strt_pg_num(131071) num_of_pgs(1) read_buf(0x273801000) W> Cannot find any partition table for 00030000 W> PARTITION_MANAGER: Failed to publish partition. ... (some lines left out) ... I> Partition name: A_spe-fw E> Cannot find partition A_spe-fw E> Partition A_spe-fw not found E> MB2_FW_LOAD: Failed to load FW. C> Task 0x0 failed (err: 0x224d090d) E> Top caller module: LOADER, error module: PARTITION_MANAGER, reason: 0x0d, aux_info: 0x09 (This first happens for Slot 0, then it switches to Slot 1 and the same issue happens again.) Those modules were brand new and never flashed before by us. What exactly does this error mean and how could this be fixed?

[image] jonathan.schnitzler: We use initrd-flash from GitHub - OE4T/meta-tegra: BSP layer for NVIDIA Jetson platforms, based on L4T · GitHub to flash the device. Sorry that we don’t support and never verified with yocto project on the devkit. You can also verify with our official L4T(Linux_for_Tegra) and check if there’s still flash/boot issue. Final status: SUCCESS Successfully finished at 2024-10-25T09:24:52+00:00 From the log you shared, it seems the flash process finished w/o errors.

Hi jonathan.schnitzler, Are you using the devkit or custom board for Orin NX? What’s the Jetpack version in use? [image] jonathan.schnitzler: We are flashing devices with Jetson Orin NX 8GB modules. How did you flash them? Could you share the flash command and full flash log for further check?

Hi KevinFFF, we are using a custom carrier board for the Orin NX. We use Jetpack 6.0 (Jetson Linux 36.3.0). We use initrd-flash from https://github.com/OE4T/meta-tegra to flash the device. It internally calls some of the Nvidia scripts. I attached the flash log of a device that failed to boot after flashing. log.initrd-flash.2024-10-25-09.22.18_stripped.txt (171.4 KB)

Boot fails with Cannot find any partition table for 00030000 after flashing

Robotics & Edge Computing Jetson Systems Jetson Orin NX

jonathan.schnitzler November 13, 2024, 2:20pm 7

It seems like we ran into Different charge numbered jetson orin nano's behave differently when writing to QSPI on custom carrier boards - #7 by DaveYYY.
We adapted our flashing procedure to properly handle the QSPI protetion bit and it now works.

Topic		Replies	Views
Orin nx qspi flash error - NV3P_SERVER: Failed to initialize partition table from GPT Jetson Orin NX reflash	6	252	June 1, 2026
Jetson Orin NX Nvme flash error Jetson Orin NX reflash	11	380	August 27, 2024
Jetson ORIN NX not booting all of suddenly,EEPROM, error module, busy spin error Jetson Orin NX boot	32	1019	October 23, 2025
Orin nano module won't flash: NV3P_SERVER: Failed to initialize partition table from GPT Jetson Orin Nano boot , reflash , board-design	2	1535	November 3, 2023
When flash bootloader only, fond one chip flash error each time Jetson Orin NX reflash , board-design	5	728	August 9, 2023
烧录qspi失败 Jetson Orin NX boot , chinese	6	852	May 8, 2024
Jetson orin NX flash failure Jetson Orin NX reflash	3	275	December 16, 2024
Flashing error Jetson orin NX Jetson Orin Nano reflash , board-design	4	469	January 2, 2025
Jetson Orin Nx device has a missing boot kernel and prompts partition size related errors during flashing Jetson Orin NX	2	122	February 25, 2025
Failed to initialize partition table from GPT Jetson Orin NX reflash	4	555	August 26, 2024

Boot fails with Cannot find any partition table for 00030000 after flashing

Related topics