here is the dmesg:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.337-tegra (buildbrain@mobile-u64-5434-d8000) (3
[ 0.000000] Boot CPU: AArch64 Processor [411fd071]
[ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 48,
[ 0.000000] OF: fdt: - 80000000 , 3f800000
[ 0.000000] OF: fdt: - bfa00000 , 3fe00000
[ 0.000000] OF: fdt: - ffa00000 , 600000
[ 0.000000] Found tegra_fbmem: 00140000@92ca9000
[ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '')
[ 0.000000] bootconsole [uart8250] enabled
[ 0.000000] OF: reserved mem: initialized node iram-carveout, compatible id t
[ 0.000000] OF: reserved mem: initialized node ramoops_carveout, compatible s
[ 0.000000] cma: Reserved 64 MiB at 0x00000000fb800000
[ 0.000000] On node 0 totalpages: 522752
[ 0.000000] DMA zone: 8192 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 522752 pages, LIFO batch:31
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] percpu: Embedded 24 pages/cpu s57816 r8192 d32296 u98304
[ 0.000000] pcpu-alloc: s57816 r8192 d32296 u98304 alloc=24*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] CPU features: enabling workaround for ARM erratum 832075
[ 0.000000] Speculative Store Bypass Disable mitigation not required
[ 0.000000] CPU features: enabling workaround for Spectre-BHB
[ 0.000000] CPU features: enabling workaround for ARM erratum 1742098
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pa0
[ 0.000000] Kernel command line: tegraid=21.1.2.0.0 ddr_die=2048M@2048M sect
[ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes
[ 0.000000] log_buf_len total cpu_extra contributions: 98304 bytes
[ 0.000000] log_buf_len min size: 32768 bytes
[ 0.000000] log_buf_len: 131072 bytes
[ 0.000000] early log buf free: 29820(91%)
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Memory: 1944796K/2091008K available (15486K kernel code, 2982K r)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 )
[ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 )
[ 0.000000] .text : 0x (ptrval) - 0x (ptrval) ( 15488 )
[ 0.000000] .rodata : 0x (ptrval) - 0x (ptrval) ( 6784 )
[ 0.000000] .init : 0x (ptrval) - 0x (ptrval) ( 8640 )
[ 0.000000] .data : 0x (ptrval) - 0x (ptrval) ( 2983 )
[ 0.000000] .bss : 0x (ptrval) - 0x (ptrval) ( 615 )
[ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 )
[ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 )
[ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 )
[ 0.000000] 0xffffffbf00000000 - 0xffffffbf02000000 ( 32 )
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc080000000 ( 2048 )
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /intr
[ 0.000000] t210 clock and reset probe
[ 0.000000] tegra-pmc: get_secure_pmc_setting: done secure_pmc=1
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] clk_cbus_recalc_rate: no gbus parent
[ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (p.
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycless
[ 0.000006] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398s
[ 0.001571] Console: colour dummy device 80x25
[ 0.001581] console [tty0] enabled
[ 0.001588] bootconsole [uart8250] disabled
[ 0.001606] kmemleak: Kernel memory leak detector disabled
[ 0.001624] Calibrating delay loop (skipped), value calculated using timer f)
[ 0.001635] pid_max: default: 32768 minimum: 301
[ 0.002111] Security Framework initialized
[ 0.002350] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.002357] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.003466] ftrace: allocating 47296 entries in 185 pages
[ 0.179092] sched-energy: CPU device node has no sched-energy-costs
[ 0.188264] ASID allocator initialised with 65536 entries
[ 0.215369] tegra-id: chipid=22117.
[ 0.215380] tegra-id: opt_subrevision=0.
[ 0.215397] Tegra Speedo/IDDQ fuse revision 4
[ 0.215401] Tegra: CPU Speedo ID 9, SoC Speedo ID 0, GPU Speedo ID 2
[ 0.215405] Tegra: CPU Process ID 0, SoC Process ID 0, GPU Process ID 0
[ 0.215411] Tegra: CPU Speedo Value 2030, SoC Speedo Value 1924, GPU Speedo 2
[ 0.215415] Tegra: CPU IDDQ Value 1792, SoC IDDQ Value 1956, GPU IDDQ Value 5
[ 0.215444] Tegra Revision: A02 SKU: 0x8f CPU Process: 0 SoC Process: 0
[ 0.215458] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9s
[ 0.215465] DTB Build time: Jun 8 2023 21:21:41
[ 0.265074] CPU1: Booted secondary processor [411fd071]
[ 0.296955] CPU2: Booted secondary processor [411fd071]
[ 0.328931] CPU3: Booted secondary processor [411fd071]
[ 0.329020] Brought up 4 CPUs
[ 0.329025] SMP: Total of 4 processors activated.
[ 0.329032] CPU features: detected feature: 32-bit EL0 Support
[ 0.329268] CPU: All CPU(s) started at EL2
[ 0.329284] alternatives: patching kernel code
[ 0.336780] devtmpfs: initialized
[ 0.373403] Initilizing CustomIPI irq domain
[ 0.373712] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ms
[ 0.373731] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.375626] pinctrl core: initialized pinctrl subsystem
[ 0.376080] OS set in device tree is not L4T.
[ 0.376466] regulator-dummy: no parameters
[ 0.376733] Initializing plugin-manager
[ 0.376860] Plugin module not found
[ 0.377230] node /plugin-manager/fragment@1 match with board >=3448-0003-400
[ 0.378402] node /plugin-manager/fragement@7 match with odm-data enable-pmict
[ 0.378611] node /plugin-manager/fragement@8 match with odm-data enable-pmict
[ 0.379069] node /plugin-manager/fragment@12 match with board >=3448-0003-400
[ 0.379329] node /plugin-manager/fragement@13 match with board >=3448-0003-40
[ 0.382942] NET: Registered protocol family 16
[ 0.384221] pstore: using zlib compression
[ 0.384256] console [pstore-1] enabled
[ 0.384260] pstore: Registered ramoops as persistent store backend
[ 0.384266] ramoops: attached 0x200000@0xb0000000, ecc: 0/0
[ 0.401091] cpuidle: using governor menu
[ 0.404019] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver
[ 0.405631] vdso: 2 pages (1 code @ (ptrval), 1 data @ (ptrv)
[ 0.405654] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.409480] atomic_pool_init():622: DMA: preallocated 1024 KiB pool for atoms
[ 0.411711] Serial: AMBA PL011 UART driver
[ 0.412203] tegra_powergate_init: DONE
[ 0.412218] DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9s
[ 0.412225] DTB Build time: Jun 8 2023 21:21:41
[ 0.413944] Tegra reboot handler registered.
[ 0.418309] iommu: Adding device tegra-carveouts to group 0
[ 0.418414] platform tegra-carveouts: domain= (ptrval) allocates as[0)
[ 0.418750] iommu: Adding device smmu_test to group 1
[ 0.418796] platform smmu_test: domain= (ptrval) allocates as[0]= )
[ 0.419611] mc: mapped MMIO address: 0x (ptrval) -> 0x70019000
[ 0.419669] mc: mapped MMIO address: 0x (ptrval) -> 0x7001c000
[ 0.419721] mc: mapped MMIO address: 0x (ptrval) -> 0x7001d000
[ 0.419730] nv-tegra-mc 70019000.mc: No mssnvlink node
[ 0.419765] mc-err: mcerr ops are set to t21x
[ 0.430438] iommu: Adding device 70090000.xusb to group 2
[ 0.430716] iommu: Adding device 70006000.serial to group 3
[ 0.430786] platform 70006000.serial: domain= (ptrval) allocates as[0)
[ 0.431192] iommu: Adding device 70006040.serial to group 4
[ 0.431462] iommu: Adding device 70006200.serial to group 5
[ 0.431685] iommu: Adding device sound to group 6
[ 0.431731] platform sound: domain= (ptrval) allocates as[0]= )
[ 0.432285] iommu: Adding device 7000d400.spi to group 7
[ 0.432550] iommu: Adding device 7000d600.spi to group 8
[ 0.432815] iommu: Adding device 70410000.spi to group 9
[ 0.433165] iommu: Adding device 50000000.host1x to group 10
[ 0.433442] iommu: Adding device 54080000.vi to group 11
[ 0.433839] iommu: Adding device 54600000.isp to group 12
[ 0.434134] iommu: Adding device 54680000.isp to group 13
[ 0.434411] iommu: Adding device tegradc.0 to group 14
[ 0.434460] platform tegradc.0: domain= (ptrval) allocates as[0]= )
[ 0.435837] platform tegradc.0: IOVA linear map 0x0000000092ca9000(140000)
[ 0.436099] iommu: Adding device 54340000.vic to group 15
[ 0.436294] iommu: Adding device 544c0000.nvenc to group 16
[ 0.436482] iommu: Adding device 54500000.tsec to group 17
[ 0.436677] iommu: Adding device 54100000.tsecb to group 18
[ 0.436901] iommu: Adding device 54480000.nvdec to group 19
[ 0.437149] iommu: Adding device 54380000.nvjpg to group 20
[ 0.437886] iommu: Adding device 546c0000.i2c to group 21
[ 0.438213] iommu: Adding device 57000000.gpu to group 22
[ 0.438260] platform 57000000.gpu: domain= (ptrval) allocates as[0]= )
[ 0.438295] platform 57000000.gpu: domain= (ptrval) allocates as[1]= )
[ 0.438332] platform 57000000.gpu: domain= (ptrval) allocates as[2]= )
[ 0.438371] platform 57000000.gpu: domain= (ptrval) allocates as[3]= )
[ 0.439232] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency .
[ 0.439244] tegra-pmc 7000e400.pmc: scratch reg offset dts data not present
[ 0.439257] tegra-pmc: ### PMC reset source: TEGRA_POWER_ON_RESET
[ 0.439261] tegra-pmc: ### PMC reset level: TEGRA_RESET_LEVEL_WARM
[ 0.439266] tegra-pmc: ### PMC reset status reg: 0x0
[ 0.489248] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registerd
[ 0.489256] tegra-pmc: Clear bootloader IO dpd settings
[ 0.489275] tegra-pmc 7000e400.pmc: IO padctrl driver initialized
[ 0.489330] tegra-pmc 7000e400.pmc: PMC: Successfully configure bootrom reses
[ 0.489617] iommu: Adding device 70012000.se to group 23
[ 0.490206] iommu: Adding device 1003000.pcie to group 24
[ 0.490272] platform 1003000.pcie: domain= (ptrval) allocates as[0]= )
[ 0.490773] iommu: Adding device 7000c000.i2c to group 25
[ 0.491038] iommu: Adding device 7000c400.i2c to group 26
[ 0.491335] iommu: Adding device 7000c500.i2c to group 27
[ 0.491595] iommu: Adding device 7000c700.i2c to group 28
[ 0.491909] iommu: Adding device 7000d000.i2c to group 29
[ 0.492229] iommu: Adding device 7000d100.i2c to group 30
[ 0.492533] iommu: Adding device sdhci-tegra.0 to group 31
[ 0.492603] platform sdhci-tegra.0: domain= (ptrval) allocates as[0]=)
[ 0.493620] iommu: Adding device 700d0000.xudc to group 32
[ 0.497454] vdd-ac-bat: 5000 mV
[ 0.497855] vdd-5v0-sys: 5000 mV
[ 0.498678] vdd-5v0-hdmi: 5000 mV
[ 0.499097] vdd-5v0-hdmi: supplied by vdd-5v0-sys
[ 0.499434] vdd-1v8-sys: 1800 mV
[ 0.499862] vdd-fan: 5000 mV
[ 0.500077] vdd-fan: supplied by vdd-5v0-sys
[ 0.500343] vdd-usb-vbus: 5000 mV
[ 0.500615] vdd-usb-vbus: supplied by vdd-5v0-sys
[ 0.501064] vdd-usb-vbus2: 5000 mV
[ 0.529996] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.532371] gpio gpiochip0: gpio-line-names specifies 240 line names but thep
[ 0.534767] GPIO line 6 (system-suspend-gpio) hogged as output/high
[ 0.534798] GPIO line 151 (camera-control-output-low) hogged as output/low
[ 0.535178] gpiochip_setup_dev: registered GPIOs 0 to 255 on device: gpiochi)
[ 0.543543] eventlib_kernel: keventlib is initialized, test id: 0
[ 0.543908] SCSI subsystem initialized
[ 0.544109] libata version 3.00 loaded.
[ 0.544458] usbcore: registered new interface driver usbfs
[ 0.544515] usbcore: registered new interface driver hub
[ 0.544616] usbcore: registered new device driver usb
[ 0.548808] max77620 4-003c: PMIC Version OTP:0x35 and ES:0x8
[ 0.553199] vdd-core: 600 <--> 1162 mV at 1125 mV
[ 0.554255] vdd-ddr-1v1: Bringing 1125000uV into 1150000-1150000uV
[ 0.557165] vdd-ddr-1v1: 1150 mV
[ 0.561090] vdd-pre-reg-1v35: 1350 mV
[ 0.565086] vdd-1v8: 1800 mV
[ 0.568274] avdd-sys-1v2: 1200 mV
[ 0.572235] vdd-pex-1v0: 1050 mV
[ 0.572878] vddio-sdmmc-ap: 1800 <--> 3300 mV at 3300 mV
[ 0.573432] max77620-ldo3: at 3100 mV
[ 0.576242] vdd-rtc: 850 <--> 1100 mV at 1000 mV
[ 0.576804] max77620-ldo5: at 3100 mV
[ 0.580234] vddio-sdmmc3-ap: 1800 <--> 3300 mV at 2800 mV
[ 0.584232] avdd-1v05-pll: 1050 mV
[ 0.588233] avdd-io-hdmi-dp: 1050 mV
[ 0.590937] GPIO line 505 (spmic-default-output-high) hogged as output/high
[ 0.591236] gpiochip_setup_dev: registered GPIOs 504 to 511 on device: gpioc)
[ 0.591528] max77620 4-003c: max77620 probe successful
[ 0.594306] media: Linux media interface: v0.10
[ 0.594361] Linux video capture interface: v2.00
[ 0.595273] pps_core: LinuxPPS API ver. 1 registered
[ 0.595281] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giom>
[ 0.595302] PTP clock support registered
[ 0.598594] tegra210-emc 7001b000.external-memory-controller: validated EMC e
[ 0.599441] Advanced Linux Sound Architecture Driver Initialized.
[ 0.600036] Bluetooth: Core ver 2.22
[ 0.600105] NET: Registered protocol family 31
[ 0.600109] Bluetooth: HCI device and connection manager initialized
[ 0.600122] Bluetooth: HCI socket layer initialized
[ 0.600131] Bluetooth: L2CAP socket layer initialized
[ 0.600154] Bluetooth: SCO socket layer initialized
[ 0.602028] tegra210_dvfs: no clock found for sdmmc2_ddr
[ 0.602049] tegra210_dvfs: no clock found for sdmmc4_ddr
[ 0.602103] tegra210_dvfs: no clock found for sdmmc1_ddr
[ 0.602121] tegra210_dvfs: no clock found for sdmmc3_ddr
[ 0.605267] tegra_dvfs: Unable to get vdd-cpu rail for step info, defering pe
[ 0.606424] vdd-3v3-sys: 3300 mV
[ 0.606761] vdd-3v3-sys: supplied by vdd-5v0-sys
[ 0.606811] vdd-1v8-sys: supplied by vdd-3v3-sys
[ 0.609151] vdd-usb-vbus2: supplied by vdd-3v3-sys
[ 0.609560] vdd-3v3-sd: 3300 mV
[ 0.609932] vdd-3v3-sd: supplied by vdd-3v3-sys
[ 0.610715] avdd-io-edp-1v05: 1050 mV
[ 0.611105] avdd-io-edp-1v05: supplied by avdd-1v05-pll
[ 0.611252] vdd-usb-hub-en: 5000 mV
[ 0.611592] vdd-usb-hub-en: supplied by vdd-1v8-sys
[ 0.612699] camchar: rtcpu character device driver loaded
[ 0.613525] extcon-gpio-states extcon:extcon@1: Cable state:0, cable id:0
[ 0.614873] clocksource: Switched to clocksource arch_sys_counter
[ 0.655173] VFS: Disk quotas dquot_6.6.0
[ 0.655303] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.655788] nvmap_heap_init: nvmap_heap_init: created heap block cache
[ 0.656257] nvmap: nvmap_select_cache_ops() nvmap cache ops set to set/ways
[ 0.656266] nvmap_page_pool_init: Total RAM pages: 502583
[ 0.656271] nvmap_page_pool_init: nvmap page pool size: 62822 pages (245 MB)
[ 0.656407] nvmap_background_zero_thread: PP zeroing thread starting.
[ 0.656708] misc nvmap: iram :dma coherent mem declare 0x0000000040001000,258
[ 0.656921] misc nvmap: created heap iram base 0x (ptrval) size (252K)
[ 0.665644] thermal thermal_zone0: Registering thermal zone thermal_zone0 fom
[ 0.666126] thermal thermal_zone1: Registering thermal zone thermal_zone1 fom
[ 0.666499] thermal thermal_zone2: Registering thermal zone thermal_zone2 fom
[ 0.666770] thermal thermal_zone3: Registering thermal zone thermal_zone3 fom
[ 0.666995] thermal thermal_zone4: Registering thermal zone thermal_zone4 foe
[ 0.667272] pre_t19x_iso_plat_init(): iso emc max clk=1600000KHz
[ 0.667276] pre_t19x_iso_plat_init(): max_iso_bw=11520000KB
[ 0.667743] NET: Registered protocol family 2
[ 0.667897] IP idents hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.683152] TCP established hash table entries: 16384 (order: 5, 131072 byte)
[ 0.683263] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 0.683509] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.683648] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.683693] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.684064] NET: Registered protocol family 1
[ 0.684713] RPC: Registered named UNIX socket transport module.
[ 0.684719] RPC: Registered udp transport module.
[ 0.684722] RPC: Registered tcp transport module.
[ 0.684725] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.684738] PCI: CLS 0 bytes, default 64
[ 0.684969] Trying to unpack rootfs image as initramfs...
[ 0.992770] Freeing initrd memory: 6988K
[ 1.002249] host1x 50000000.host1x: initialized
[ 1.004107] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters ae
[ 1.007418] audit: initializing netlink subsys (disabled)
[ 1.007489] audit: type=2000 audit(0.851:1): initialized
[ 1.008173] workingset: timestamp_bits=46 max_order=19 bucket_order=0
[ 1.017890] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.019407] ntfs: driver 2.1.32 [Flags: R/W].
[ 1.020192] 9p: Installing v9fs 9p2000 file system support
[ 1.023562] Block layer SCSI generic (bsg) driver version 0.4 loaded (major )
[ 1.023670] io scheduler noop registered
[ 1.023967] io scheduler cfq registered (default)
[ 1.026649] gic 702f9000.agic: GIC IRQ controller registered
[ 1.029755] iommu: Adding device 702ef000.adsp to group 33
[ 1.038615] iommu: Adding device aconnect@702c0000:adsp_audio to group 34
[ 1.038798] tegra-aconnect aconnect@702c0000: Tegra ACONNECT bus registered
[ 1.039473] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 =1
[ 1.039480] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT4
[ 1.041057] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane =b
[ 1.041155] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane =b
[ 1.041255] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane =b
[ 1.041462] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane =1
[ 1.041547] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane =4
[ 1.041639] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane =4
[ 1.041724] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane =4
[ 1.041817] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane =4
[ 1.041901] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane =b
[ 1.041989] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane =b
[ 1.042580] tegra-xusb-padctl 7009f000.xusb_padctl: failed to setup XUSB por7
[ 1.049266] tegra-pwm 7000a000.pwm: PWM clk cannot sleep in ops
[ 1.050900] tegra-dfll-pwm 70110000.pwm: DFLL pwm-rate: 12800000
[ 1.052785] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration
[ 1.052819] tegra-pcie 1003000.pcie: PHY get deferred: -517
[ 1.052825] tegra-pcie 1003000.pcie: failed to get PHYs: -517
[ 1.054229] tegra_camera_platform tegra-camera-platform: tegra_camera_probe:e
[ 1.054430] misc tegra_camera_ctrl: tegra_camera_isomgr_register isp_iso_bw=0
[ 1.054673] Adding domain tsec-pd to PM domain host1x-pd
[ 1.057472] tsec 54500000.tsec: initialized
[ 1.058801] tsec 54100000.tsecb: initialized
[ 1.059509] Adding domain nvdec-pd to PM domain host1x-pd
[ 1.062500] nvdec 54480000.nvdec: initialized
[ 1.063567] Adding domain vic03-pd to PM domain host1x-pd
[ 1.063743] Adding domain msenc-pd to PM domain host1x-pd
[ 1.063906] Adding domain nvjpg-pd to PM domain host1x-pd
[ 1.067757] falcon 54340000.vic: initialized
[ 1.068967] falcon 544c0000.nvenc: initialized
[ 1.070298] falcon 54380000.nvjpg: initialized
[ 1.074530] tegra_cec 70015000.tegra_cec: dt=1 start=0x70015000 end=0x70015F5
[ 1.074572] tegra_cec 70015000.tegra_cec: Enable clock result: 0.
[ 1.074605] tegra_cec 70015000.tegra_cec: tegra_cec_init started
[ 1.074659] tegradc tegradc.0: disp0 connected to head0->/host1x/sor1
[ 1.074752] display board info: id 0x0, fab 0x0
[ 1.074808] generic_infoframe_type: 0x87
[ 1.074890] tegra_cec 70015000.tegra_cec: cec_add_sysfs ret=0
[ 1.074896] tegra_cec 70015000.tegra_cec: probed
[ 1.075001] tegradc tegradc.0: DT parsed successfully
[ 1.075047] tegradc tegradc.0: Display dc. (ptrval) registered with i0
[ 1.075599] tegradc tegradc.0: Bootloader disp_param detected. Detected mode6
[ 1.078941] tegradc tegradc.0: probed
[ 1.084249] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 chs
[ 1.090592] tegra-adma 702e2000.adma: Tegra210 ADMA driver registered 22 chas
[ 1.091549] tegra-fuse-burn 7000f800.efuse:efuse-burn: shutdown limit check d
[ 1.091556] tegra-fuse-burn 7000f800.efuse:efuse-burn: Fuse burn driver initd
[ 1.091926] kfuse 7000fc00.kfuse: initialized
[ 1.093261] tegra-pmc-iopower pmc-iopower: Regulator supply iopower-dbg-suppe
[ 1.094228] tegra-pmc-iopower pmc-iopower: NO_IOPOWER setting 0x0
[ 1.095635] tegra-dfll-pwm 70110000.pwm: DFLL_PWM regulator is available now
[ 1.095654] vdd-cpu: 708 <--> 1322 mV at 708 mV
[ 1.096137] pwm-regulator pwm_regulators:pwm-regulator@0: PWM regulator regid
[ 1.097663] vdd-gpu: applied init 1000000uV constraint
[ 1.097670] vdd-gpu: 708 <--> 1323 mV at 997 mV
[ 1.098076] pwm-regulator pwm_regulators:pwm-regulator@1: PWM regulator regid
[ 1.102269] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.102365] No Device Node present for smmu client: serial8250 !!
[ 1.102376] platform serial8250: No iommus property found in DT node, got sw)
[ 1.102421] iommu: Adding device serial8250 to group 35
[ 1.104804] console [ttyS0] disabled
[ 1.104890] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 63, base_baud =a
[ 1.104989] console [ttyS0] enabled
[ 1.105470] Console: switching to colour frame buffer device 80x30
[ 1.105506] tegradc tegradc.0: fb registered
[ 1.106415] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 64, base_baudT
[ 1.106848] serial-tegra 70006200.serial: RX in PIO mode
[ 1.107018] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 65, base_baudT
[ 1.108209] [drm] Initialized
[ 1.112904] tegradc tegradc.0: DC initialized, skipping tegra_dc_program_mod.
[ 1.112956] tegradc tegradc.0: hdmi: tmds rate:25174K prod-setting:prod_c_hdm
[ 1.113466] tegradc tegradc.0: hdmi: get RGB quant from REG programmed by BL.
[ 1.113477] tegradc tegradc.0: hdmi: BL set VIC 0
[ 1.113482] tegradc tegradc.0: hdmi: get YCC quant from REG programmed by BL.
[ 1.118953] brd: module loaded
[ 1.124557] loop: module loaded
[ 1.124641] tegra_profiler: version: 1.145, samples/io: 49/28
[ 1.124753] tegra_profiler: auth: init
[ 1.126099] THERMAL EST: found 2 subdevs
[ 1.126107] THERMAL EST num_resources: 0
[ 1.126121] [THERMAL EST subdev 0]
[ 1.126128] [THERMAL EST subdev 1]
[ 1.126594] thermal thermal_zone5: Registering thermal zone thermal_zone5 fot
[ 1.126597] THERMAL EST: thz register success.
[ 1.126819] THERMAL EST: end of probe, return err: 0
[ 1.128238] sd: No Scsi addr parsed to reserve index
[ 1.128282] hisi_sas: driver version v1.6
[ 1.133101] tegra-qspi 70410000.spi: Prod settings list not found
[ 1.134262] qspi_mtd spi32766.0: MX25U3235F (4096 Kbytes)
[ 1.134272] qspi_mtd spi32766.0: mtd .name = spi32766.0, .size = 0x400000 (40
[ 1.138003] tun: Universal TUN/TAP device driver, 1.6
[ 1.138013] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.139060] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 1.139063] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 1.139117] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
[ 1.139122] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 1.139166] igbvf: Intel(R) Gigabit Virtual Function Network Driver - versiok
[ 1.139169] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[ 1.139215] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version k
[ 1.139219] ixgbe: Copyright (c) 1999-2016 Intel Corporation.
[ 1.139888] extcon-disp-state extcon:disp-state: cable 47 state 1
[ 1.139896] Extcon AUX1(HDMI) enable
[ 1.140551] PPP generic driver version 2.4.2
[ 1.140771] PPP BSD Compression module registered
[ 1.140776] PPP Deflate Compression module registered
[ 1.140817] PPP MPPE Compression module registered
[ 1.140824] NET: Registered protocol family 24
[ 1.140902] usbcore: registered new interface driver r8152
[ 1.140950] usbcore: registered new interface driver asix
[ 1.141007] usbcore: registered new interface driver ax88179_178a
[ 1.141049] usbcore: registered new interface driver cdc_ether
[ 1.141088] usbcore: registered new interface driver net1080
[ 1.141127] usbcore: registered new interface driver cdc_subset
[ 1.141165] usbcore: registered new interface driver zaurus
[ 1.141234] usbcore: registered new interface driver cdc_ncm
[ 1.141404] VFIO - User Level meta-driver version: 0.3
[ 1.142737] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.142761] ehci-pci: EHCI PCI platform driver
[ 1.142805] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.142817] ohci-pci: OHCI PCI platform driver
[ 1.142907] ohci-platform: OHCI generic platform driver
[ 1.144779] usbcore: registered new interface driver uas
[ 1.144841] usbcore: registered new interface driver usb-storage
[ 1.144974] usbcore: registered new interface driver usbserial
[ 1.152643] mousedev: PS/2 mouse device common for all mice
[ 1.152730] usbcore: registered new interface driver xpad
[ 1.176834] tegradc tegradc.0: nominal-pclk:25174825 parent:25173906 div:1.02
[ 1.274406] tegradc tegradc.0: blank - powerdown
[ 1.279770] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as 0
[ 1.281919] rtc rtc1: alarm rtc device
[ 1.281931] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1
[ 1.281948] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock
[ 1.282307] i2c /dev entries driver
[ 1.283874] imx219 6-0010: tegracam sensor driver:imx219_v2.0.6
[ 1.307162] tegra-vii2c 546c0000.i2c: no acknowledge from address 0x10
[ 1.307236] imx219 6-0010: imx219_board_setup: error during i2c read probe ()
[ 1.307304] imx219 6-0010: board setup failed
[ 1.307355] imx219: probe of 6-0010 failed with error -121
[ 1.308418] max77620-power max77620-power: Event recorder REG_NVERC : 0x0
[ 1.310367] tegra_soctherm 700e2000.soctherm: pllx_offset tz:0 max:14, min:2
[ 1.310371] tegra_soctherm 700e2000.soctherm: pllx_offset tz:2 max:8, min:4
[ 1.310679] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -210
[ 1.310691] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down whenC
[ 1.310698] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when C
[ 1.310821] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -210
[ 1.310830] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down whenC
[ 1.310836] tegra_soctherm 700e2000.soctherm: throttrip: will throttle when C
[ 1.311009] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -210
[ 1.311017] tegra_soctherm 700e2000.soctherm: thermtrip: will shut down whenC
[ 1.311021] tegra_soctherm 700e2000.soctherm: throttrip: pll: missing hot tee
[ 1.311191] tegra_soctherm 700e2000.soctherm: failed to register sensor: -19
[ 1.311722] tegra_aotag tegra-aotag: Registering sensor 0
[ 1.311764] tegra_aotag tegra-aotag: Invalid temp readout
[ 1.311784] tegra_aotag tegra-aotag: Invalid temp readout
[ 1.311800] tegra_aotag tegra-aotag: Bound to TZ : ID 0
[ 1.311808] tegra_aotag tegra-aotag: Probe done [SUCCESS]:0
[ 1.312560] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -210
[ 1.312574] tegra_dfll_action dfll-cdev-cap: Tegra DFLL 'cap cooling device'd
[ 1.312723] tegra_aotag tegra-aotag: Invalid temp readout
[ 1.312744] tegra_dfll_action dfll-cdev-floor: Tegra DFLL 'floor cooling devd
[ 1.313085] parse_throttle_dt_data: Num cap clks = 6
[ 1.313089] parse_throttle_dt_data: clk=cclk_g type=2
[ 1.313096] parse_throttle_dt_data: clk=gpu type=4
[ 1.313114] parse_throttle_dt_data: clk=cap.throttle.c2bus type=0
[ 1.313134] parse_throttle_dt_data: clk=cap.throttle.c3bus type=0
[ 1.313155] parse_throttle_dt_data: clk=cap.throttle.sclk type=0
[ 1.313158] parse_throttle_dt_data: clk=emc type=3
[ 1.313497] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -210
[ 1.313627] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -210
[ 1.313762] tegra_throttle_probe: probe successful. #cdevs=4
[ 1.314388] FAN dev name: pwm-fan
[ 1.314432] FAN:gpio request success.
[ 1.314480] pwm_fan_driver pwm-fan: cap state:7, cap pwm:255
[ 1.314505] extcon-disp-state extcon:disp-state: cable 47 state 0
[ 1.314508] Extcon AUX1(HDMI) disable
[ 1.314713] pwm_fan_driver pwm-fan: got pwm for fan. polarity is normal
[ 1.314829] pwm_fan_driver pwm-fan: fan tach request irq success
[ 1.314835] pwm_fan_driver pwm-fan: tach period: 1000
[ 1.314932] pwm_fan_driver pwm-fan: index 0: pwm=0, rpm=0, rru=40, rrd=40, s2
[ 1.314936] pwm_fan_driver pwm-fan: index 1: pwm=80, rpm=1000, rru=2, rrd=2,2
[ 1.314940] pwm_fan_driver pwm-fan: index 2: pwm=120, rpm=2000, rru=1, rrd=12
[ 1.314945] pwm_fan_driver pwm-fan: index 3: pwm=160, rpm=3000, rru=1, rrd=12
[ 1.314949] pwm_fan_driver pwm-fan: index 4: pwm=255, rpm=4000, rru=1, rrd=13
[ 1.314953] pwm_fan_driver pwm-fan: index 5: pwm=255, rpm=5000, rru=1, rrd=13
[ 1.314956] pwm_fan_driver pwm-fan: index 6: pwm=255, rpm=6000, rru=1, rrd=13
[ 1.314960] pwm_fan_driver pwm-fan: index 7: pwm=255, rpm=7000, rru=1, rrd=14
[ 1.314964] pwm_fan_driver pwm-fan: index 8: pwm=255, rpm=10000, rru=1, rrd=4
[ 1.314968] pwm_fan_driver pwm-fan: index 9: pwm=255, rpm=11000, rru=1, rrd=4
[ 1.317359] device-mapper: uevent: version 1.0.3
[ 1.317785] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-m
[ 1.320424] tegra210-cpufreq cpufreq: probe()...completed
[ 1.321328] sdhci: Secure Digital Host Controller Interface driver
[ 1.321329] sdhci: Copyright(c) Pierre Ossman
[ 1.321331] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.321813] sdhci-tegra sdhci-tegra.0: Got CD GPIO
[ 1.322193] sdhci-tegra sdhci-tegra.0: Client registration for eMC Successful
[ 1.322317] sdhci-tegra sdhci-tegra.0: wakeup init done, cdirq 298
[ 1.327150] tegra-se 70012000.se: tegra_se_probe: complete
[ 1.327657] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.328847] usbcore: registered new interface driver usbhid
[ 1.328848] usbhid: USB HID core driver
[ 1.329160] ashmem: initialized
[ 1.330106] tegra21x_actmon 6000c800.actmon: in actmon_register()...
[ 1.330274] tegra21x_actmon 6000c800.actmon: initialization Completed for thl
[ 1.332653] nvpmodel: initialized successfully
[ 1.333636] usbcore: registered new interface driver snd-usb-audio
[ 1.333696] No Device Node present for smmu client: snd-soc-dummy !!
[ 1.333700] platform snd-soc-dummy: No iommus property found in DT node, got)
[ 1.333717] iommu: Adding device snd-soc-dummy to group 36
[ 1.339409] input: tegra-hda HDMI/DP,pcm=3 as /devices/70030000.hda/sound/ca0
[ 1.339708] tegradc tegradc.0: unblank
[ 1.354562] tegradc tegradc.0: nominal-pclk:49000000 parent:48999316 div:1.00
[ 1.354640] tegradc tegradc.0: hdmi: tmds rate:49000K prod-setting:prod_c_hdm
[ 1.355666] tegradc tegradc.0: hdmi: get YCC quant from EDID.
[ 1.356654] OPE platform probe
[ 1.356741] OPE platform probe successful
[ 1.356998] OPE platform probe
[ 1.357074] OPE platform probe successful
[ 1.371131] mmc0: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADr
[ 1.381066] tegra-asoc: sound: ADMAIF1 <-> ADMAIF1 mapping ok
[ 1.381200] tegra-asoc: sound: ADMAIF2 <-> ADMAIF2 mapping ok
[ 1.381327] tegra-asoc: sound: ADMAIF3 <-> ADMAIF3 mapping ok
[ 1.381451] tegra-asoc: sound: ADMAIF4 <-> ADMAIF4 mapping ok
[ 1.381578] tegra-asoc: sound: ADMAIF5 <-> ADMAIF5 mapping ok
[ 1.381704] tegra-asoc: sound: ADMAIF6 <-> ADMAIF6 mapping ok
[ 1.381831] tegra-asoc: sound: ADMAIF7 <-> ADMAIF7 mapping ok
[ 1.381956] tegra-asoc: sound: ADMAIF8 <-> ADMAIF8 mapping ok
[ 1.382084] tegra-asoc: sound: ADMAIF9 <-> ADMAIF9 mapping ok
[ 1.382209] tegra-asoc: sound: ADMAIF10 <-> ADMAIF10 mapping ok
[ 1.390515] extcon-disp-state extcon:disp-state: cable 47 state 1
[ 1.390517] Extcon AUX1(HDMI) enable
[ 1.398667] u32 classifier
[ 1.398668] Actions configured
[ 1.398736] Initializing XFRM netlink socket
[ 1.399491] NET: Registered protocol family 10
[ 1.400167] NET: Registered protocol family 17
[ 1.400177] NET: Registered protocol family 15
[ 1.400258] bridge: filtering via arp/ip/ip6tables is no longer available by.
[ 1.400303] Bluetooth: RFCOMM socket layer initialized
[ 1.400313] Bluetooth: RFCOMM ver 1.11
[ 1.400318] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.400322] Bluetooth: HIDP socket layer initialized
[ 1.400339] 9pnet: Installing 9P2000 support
[ 1.400371] Key type dns_resolver registered
[ 1.400741] Registered cp15_barrier emulation handler
[ 1.400747] Registered setend emulation handler
[ 1.401805] registered taskstats version 1
[ 1.402332] Adding domain ve2-pd to PM domain host1x-pd
[ 1.402584] Adding domain ve-pd to PM domain host1x-pd
[ 1.404537] isp 54600000.isp: initialized
[ 1.405483] isp 54680000.isp: initialized
[ 1.405870] tegradc tegradc.0: sync windows ret = 247
[ 1.416008] last reset is due to power on reset
[ 1.416010] KERNEL: PMC reset status reg: 0x0
[ 1.416066] BL: PMC reset status reg: 0x0
[ 1.416067] BL: PMIC poweroff Event Recorder: 0x40
[ 1.416597] vdd-usb-vbus-en: 5000 mV
[ 1.416934] vdd-usb-vbus-en: supplied by vdd-5v0-sys
[ 1.417905] clk_cbus_recalc_rate: no gbus parent
[ 1.417910] clk_cbus_round_rate: no gbus parent
[ 1.417911] clk_cbus_round_rate: no gbus parent
[ 1.417916] clk_cbus_recalc_rate: no gbus parent
[ 1.418005] clk_cbus_recalc_rate: no gbus parent
[ 1.418008] clk_cbus_round_rate: no gbus parent
[ 1.418009] clk_cbus_round_rate: no gbus parent
[ 1.418012] clk_cbus_recalc_rate: no gbus parent
[ 1.418679] tegra_dvfs: GPU-cap: registered
[ 1.418744] tegra dvfs: vdd-cpu: nominal 1168mV, offset 708000uV, step 19200d
[ 1.418746] tegra dvfs: vdd-core: nominal 1125mV, offset 600000uV, step 1250d
[ 1.418748] tegra dvfs: vdd-gpu: nominal 1078mV, offset 708000uV, step 10000d
[ 1.420188] tegra_dvfs: vdd-gpu-vts: registered
[ 1.420329] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_SKU_CALIB_0 =1
[ 1.420333] tegra-xusb-padctl 7009f000.xusb_padctl: TEGRA_FUSE_USB_CALIB_EXT4
[ 1.421025] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.0, lane =b
[ 1.421083] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.1, lane =b
[ 1.421146] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-usb2.2, lane =b
[ 1.421251] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.3, lane =1
[ 1.421305] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.4, lane =4
[ 1.421358] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.5, lane =4
[ 1.421412] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.6, lane =4
[ 1.421463] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.7, lane =4
[ 1.421516] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.8, lane =b
[ 1.421568] tegra-xusb-padctl 7009f000.xusb_padctl: dev = phy-pcie.9, lane =b
[ 1.422994] tegra-pcie 1003000.pcie: 4x1, 1x1 configuration
[ 1.425195] tegra-xusb 70090000.xusb: USB2 port 0 has OTG_CAP
[ 1.425316] tegra-pcie 1003000.pcie: PCIE: Enable power rails
[ 1.426001] tegra-pcie 1003000.pcie: probing port 0, using 4 lanes
[ 1.426015] tegra-xusb-padctl 7009f000.xusb_padctl: enabled OTG on UTMI pad 0
[ 1.427107] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes
[ 1.427183] tegra-xusb 70090000.xusb: extcon 0: (ptrval) id
[ 1.428638] tegra-xudc-new 700d0000.xudc: device count: 1
[ 1.429718] tegra-xudc-new 700d0000.xudc: USB charger detection disabled
[ 1.429725] tegra-xudc-new 700d0000.xudc: vbus state: 0
[ 1.430151] tegra-xudc-new 700d0000.xudc: entering ELPG
[ 1.430415] tegra_core_action core_dvfs_cdev_floor: Tegra CORE DVFS 'floor cd
[ 1.430602] tegra-xusb 70090000.xusb: Firmware timestamp: 2023-04-25 07:35:5e
[ 1.430629] tegra-xusb 70090000.xusb: xHCI Host Controller
[ 1.430639] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus n1
[ 1.431358] tegra-xusb 70090000.xusb: hcc params 0x0184f525 hci version 0x100
[ 1.431385] tegra-xusb 70090000.xusb: irq 61, io mem 0x70090000
[ 1.431675] tegra-xudc-new 700d0000.xudc: entering ELPG done
[ 1.432207] tegra_core_action core_dvfs_cdev_cap: Tegra CORE DVFS 'cap coolid
[ 1.432289] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.432292] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber1
[ 1.432295] usb usb1: Product: xHCI Host Controller
[ 1.432298] usb usb1: Manufacturer: Linux 4.9.337-tegra xhci-hcd
[ 1.432300] usb usb1: SerialNumber: 70090000.xusb
[ 1.432696] hub 1-0:1.0: USB hub found
[ 1.432723] hub 1-0:1.0: 5 ports detected
[ 1.432770] input: gpio-keys as /devices/gpio-keys/input/input1
[ 1.433088] tegra-xusb 70090000.xusb: xHCI Host Controller
[ 1.433095] tegra-xusb 70090000.xusb: new USB bus registered, assigned bus n2
[ 1.433210] usb usb2: We don't know the algorithms for LPM for this host, di.
[ 1.433275] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.433279] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber1
[ 1.433281] usb usb2: Product: xHCI Host Controller
[ 1.433284] usb usb2: Manufacturer: Linux 4.9.337-tegra xhci-hcd
[ 1.433286] usb usb2: SerialNumber: 70090000.xusb
[ 1.433554] hub 2-0:1.0: USB hub found
[ 1.433574] hub 2-0:1.0: 4 ports detected
[ 1.434036] tegra-xusb 70090000.xusb: Upgrade port 0 to USB3.0
[ 1.434039] tegra-xusb 70090000.xusb: Upgrade port 1 to USB3.0
[ 1.436789] extcon-disp-state extcon:disp-state: cable 51 state 1
[ 1.436792] Extcon HDMI: HPD enabled
[ 1.436808] tegradc tegradc.0: hdmi: plugged
[ 1.458918] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1
[ 1.458971] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 2
[ 1.464361] tegra_rtc 7000e000.rtc: setting system clock to 2000-01-01 01:00)
[ 1.465332] vi 54080000.vi: vi_probe: ++
[ 1.468504] vi 54080000.vi: initialized
[ 1.470541] vi 54080000.vi: subdev nvcsi--1 bound
[ 1.471376] Disable partitions left on by BL
[ 1.471379] disb
[ 1.471418] bwmgr: missing cdev-type property
[ 1.471538] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -210
[ 1.471544] DRAM derating cdev registered.
[ 1.472498] ALSA device list:
[ 1.472502] #0: tegra-hda at 0x70038000 irq 81
[ 1.472504] #1: tegra-snd-t210ref-mobile-rt565x
[ 1.475882] Freeing unused kernel memory: 8640K
[ 1.499940] Root device found: mmcblk0p1
[ 1.572496] extcon-disp-state extcon:disp-state: cable 47 state 0
[ 1.572500] Extcon AUX1(HDMI) disable
[ 1.573747] mmc0: Applying tuning correction
[ 1.573761] mmc0: Tap value after applying correction 56
[ 1.573780] mmc0: hw tuning done ...
[ 1.573815] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 1.574112] mmcblk0: mmc0:aaaa SN64G 59.5 GiB
[ 1.579262] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14
[ 1.592847] tegradc tegradc.0: blank - powerdown
[ 1.592957] extcon-disp-state extcon:disp-state: cable 51 state 0
[ 1.592959] Extcon HDMI: HPD disabled
[ 1.592971] tegradc tegradc.0: hdmi: unplugged
[ 1.682935] usb 1-2: new full-speed USB device number 2 using tegra-xusb
[ 1.705127] usb 1-2: New USB device found, idVendor=0483, idProduct=5750
[ 1.705132] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.705136] usb 1-2: Product: ByQDtech �触�控USB�鼠�标
[ 1.705139] usb 1-2: Manufacturer: �深�圳�市�全�动�电�子�技�术�有�限�公�司
[ 1.705142] usb 1-2: SerialNumber: DB17ECDCA9FC
[ 1.705955] Found dev node: /dev/mmcblk0p1
[ 1.707575] input: �深�圳�市�全�动�电�子�技�术�有�限�公�司 ByQDtech �触�控US2
[ 1.707968] hid-multitouch 0003:0483:5750.0001: input,hidraw0: USB HID v1.100
[ 1.760139] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. )
[ 1.761980] Rootfs mounted over mmcblk0p1
[ 1.799506] Switching from initrd to actual rootfs
[ 1.826897] usb 1-3: new high-speed USB device number 3 using tegra-xusb
[ 1.847269] usb 1-3: New USB device found, idVendor=1a40, idProduct=0801
[ 1.847274] usb 1-3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1.847277] usb 1-3: Product: USB 2.0 Hub
[ 1.848082] hub 1-3:1.0: USB hub found
[ 1.848151] hub 1-3:1.0: 4 ports detected
[ 1.850886] tegra-pcie 1003000.pcie: link 0 down, retrying
[ 1.943063] usb usb2: usb_suspend_both: status 0
[ 2.074940] tegra_cec 70015000.tegra_cec: Can't find physical addresse.
[ 2.074944] tegra_cec 70015000.tegra_cec: tegra_cec_init Done.
[ 2.082032] systemd[1]: System time before build time, advancing clock.
[ 2.126761] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.134893] usb 1-3.2: new high-speed USB device number 4 using tegra-xusb
[ 2.142567] cgroup: cgroup2: unknown option "nsdelegate"
[ 2.154550] tegradc tegradc.0: blank - powerdown
[ 2.155623] usb 1-3.2: New USB device found, idVendor=0bda, idProduct=c811
[ 2.155627] usb 1-3.2: New USB device strings: Mfr=1, Product=2, SerialNumbe3
[ 2.155630] usb 1-3.2: Product: 802.11ac NIC
[ 2.155633] usb 1-3.2: Manufacturer: Realtek
[ 2.155635] usb 1-3.2: SerialNumber: 123456
[ 2.156834] tegradc tegradc.0: unblank
[ 2.162102] tegradc tegradc.0: nominal-pclk:49000000 parent:48999316 div:1.00
[ 2.162155] tegradc tegradc.0: hdmi: tmds rate:49000K prod-setting:prod_c_hdm
[ 2.163177] tegradc tegradc.0: hdmi: get YCC quant from EDID.
[ 2.197976] extcon-disp-state extcon:disp-state: cable 47 state 1
[ 2.197978] Extcon AUX1(HDMI) enable
[ 2.213410] tegradc tegradc.0: sync windows ret = 246
[ 2.232412] extcon-disp-state extcon:disp-state: cable 51 state 1
[ 2.232414] Extcon HDMI: HPD enabled
[ 2.232425] tegradc tegradc.0: hdmi: plugged
[ 2.232599] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SE)
[ 2.233380] systemd[1]: Detected architecture arm64.
[ 2.257179] systemd[1]: Set hostname to <nano-desktop>.
[ 2.264886] tegra-pcie 1003000.pcie: link 0 down, retrying
[ 2.439110] systemd[1]: File /lib/systemd/system/systemd-journald.service:36.
[ 2.439119] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warn)
[ 2.669041] tegra-pcie 1003000.pcie: link 0 down, retrying
[ 2.671058] tegra-pcie 1003000.pcie: link 0 down, ignoring
[ 2.675095] random: systemd: uninitialized urandom read (16 bytes read)
[ 2.675323] systemd[1]: Started Forward Password Requests to Wall Directory .
[ 2.675444] random: systemd: uninitialized urandom read (16 bytes read)
[ 2.675468] systemd[1]: Reached target Mounting snaps.
[ 2.675489] random: systemd: uninitialized urandom read (16 bytes read)
[ 2.675512] systemd[1]: Reached target Mounted snaps.
[ 2.677508] systemd[1]: Created slice System Slice.
[ 2.677710] systemd[1]: Listening on udev Kernel Socket.
[ 2.777289] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00
[ 2.777296] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 2.777301] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff]
[ 2.777305] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pr]
[ 2.777310] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 2.777333] pci 0000:00:02.0: [10de:0faf] type 01 class 0x060400
[ 2.777405] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 2.777539] iommu: Adding device 0000:00:02.0 to group 37
[ 2.777624] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reg
[ 2.777759] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000
[ 2.777786] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x00ff]
[ 2.777821] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit]
[ 2.777843] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit]
[ 2.778007] pci 0000:01:00.0: supports D1 D2
[ 2.778010] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 2.778189] iommu: Adding device 0000:01:00.0 to group 38
[ 2.787049] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 2.787081] pci 0000:00:02.0: BAR 14: assigned [mem 0x13000000-0x130fffff]
[ 2.787085] pci 0000:00:02.0: BAR 13: assigned [io 0x1000-0x1fff]
[ 2.787092] pci 0000:01:00.0: BAR 4: assigned [mem 0x13000000-0x13003fff 64b]
[ 2.787111] pci 0000:01:00.0: BAR 2: assigned [mem 0x13004000-0x13004fff 64b]
[ 2.787129] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff]
[ 2.787137] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 2.787141] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff]
[ 2.787146] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff]
[ 2.787444] pcieport 0000:00:02.0: Signaling PME through PCIe PME interrupt
[ 2.787450] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[ 2.787455] pcie_pme 0000:00:02.0:pcie001: service driver pcie_pme loaded
[ 2.787550] aer 0000:00:02.0:pcie002: service driver aer loaded
[ 2.787748] r8168 0000:01:00.0: enabling device (0000 -> 0003)
[ 2.787766] r8168 Gigabit Ethernet driver 8.045.08-NAPI loaded
[ 2.801863] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Invalide
[ 2.801946] r8168 0000:01:00.0 (unnamed net_device) (uninitialized): Found ve
[ 2.802504] r8168: This product is covered by one or more of the following p.
[ 2.802521] r8168 Copyright (C) 2017 Realtek NIC software team <nicfae@rea
This program comes with ABSOLUTELY NO WARRANTY; for details, pl
This is free software, and you are welcome to redistribute it u
[ 2.823948] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
[ 2.873771] nvgpu: 57000000.gpu gm20b_init_clk_setup_sw:1268 [INFO)
[ 3.124905] systemd-journald[1957]: Received request to flush runtime journa1
[ 3.228730] Adding 4194300k swap on /mnt/swapfile_4G. Priority:-1 extents:2S
[ 3.249016] Adding 4194300k swap on /swapfile. Priority:-2 extents:5 acrossS
[ 3.682031] random: systemd-journal: uninitialized urandom read (16 bytes re)
[ 3.691086] random: systemd-journal: uninitialized urandom read (16 bytes re)
[ 3.699840] random: systemd-journal: uninitialized urandom read (16 bytes re)
[ 4.012482] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -210
[ 4.012503] cpu-throttle-alert cooling device registered.
[ 4.012634] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -210
[ 4.012648] gpu-throttle-alert cooling device registered.
[ 4.012793] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -210
[ 4.012805] tegra_soctherm 700e2000.soctherm: soctherm: trip temperature -210
[ 4.012816] hot-surface-alert cooling device registered.
[ 4.170912] random: crng init done
[ 4.174351] random: 147 urandom warning(s) missed due to ratelimiting
[ 4.986940] using random self ethernet address
[ 4.991466] using random host ethernet address
[ 6.022698] usbcore: registered new interface driver rtl8821cu
[ 6.725131] Mass Storage Function, version: 2009/09/11
[ 6.725137] LUN: removable file: (no medium)
[ 6.732070] using random self ethernet address
[ 6.736775] using random host ethernet address
[ 6.864187] rndis0: HOST MAC a6:19:1a:b2:93:e8
[ 6.864517] rndis0: MAC a6:19:1a:b2:93:e9
[ 6.865790] usb0: HOST MAC a6:19:1a:b2:93:ea
[ 6.865990] usb0: MAC a6:19:1a:b2:93:eb
[ 6.866015] tegra-xudc-new 700d0000.xudc: exiting ELPG
[ 6.869360] tegra-xudc-new 700d0000.xudc: exiting ELPG done
[ 6.869380] tegra-xudc-new 700d0000.xudc: ep 0 (type: 0, dir: out) enabled
[ 6.869413] tegra-xudc-new 700d0000.xudc: entering ELPG
[ 6.869653] tegra-xudc-new 700d0000.xudc: entering ELPG done
[ 6.869677] tegra-xudc-new 700d0000.xudc: exiting ELPG
[ 6.870175] tegra-xudc-new 700d0000.xudc: exiting ELPG done
[ 6.870188] tegra-xudc-new 700d0000.xudc: entering ELPG
[ 6.870407] tegra-xudc-new 700d0000.xudc: entering ELPG done
[ 6.878936] l4tbr0: port 1(rndis0) entered blocking state
[ 6.878940] l4tbr0: port 1(rndis0) entered disabled state
[ 6.880424] device rndis0 entered promiscuous mode
[ 6.885659] IPv6: ADDRCONF(NETDEV_UP): rndis0: link is not ready
[ 6.889768] l4tbr0: port 2(usb0) entered blocking state
[ 6.889772] l4tbr0: port 2(usb0) entered disabled state
[ 6.889945] device usb0 entered promiscuous mode
[ 6.896152] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready
[ 7.031606] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 7.053457] eth0: 0xffffff800d585000, 48:b0:2d:2f:40:47, IRQ 405
[ 7.103457] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 7.194242] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 7.797583] zram: Added device: zram0
[ 7.799641] zram: Added device: zram1
[ 7.802609] zram: Added device: zram2
[ 7.803944] zram: Added device: zram3
[ 7.827001] zram0: detected capacity change from 0 to 259325952
[ 7.873778] Adding 253244k swap on /dev/zram0. Priority:5 extents:1 across:S
[ 7.881656] zram1: detected capacity change from 0 to 259325952
[ 7.901108] Adding 253244k swap on /dev/zram1. Priority:5 extents:1 across:S
[ 7.904396] zram2: detected capacity change from 0 to 259325952
[ 7.914701] Adding 253244k swap on /dev/zram2. Priority:5 extents:1 across:S
[ 7.922390] zram3: detected capacity change from 0 to 259325952
[ 7.940708] Adding 253244k swap on /dev/zram3. Priority:5 extents:1 across:S
[ 7.983212] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 8.004637] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 8.098097] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 8.296504] Bridge firewalling registered
[ 8.469491] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 8.904444] Netfilter messages via NETLINK v0.30.
[ 8.939313] ctnetlink v0.93: registering with nfnetlink.
[ 9.073859] IPv6: ADDRCONF(NETDEV_UP): docker0: link is not ready
[ 9.874657] tegradc tegradc.0: unblank
[ 11.415537] fuse init (API version 7.26)
[ 12.350834] tegradc tegradc.0: blank - powerdown
[ 12.406025] extcon-disp-state extcon:disp-state: cable 47 state 0
[ 12.406027] Extcon AUX1(HDMI) disable
[ 13.036219] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 13.350407] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 14.818381] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 14.818391] Bluetooth: BNEP socket layer initialized
[ 31.867088] vdd-fan: disabling
[ 31.867092] vdd-usb-vbus: disabling
[ 31.867094] vdd-usb-vbus2: disabling
[ 31.867104] vddio-sdmmc3-ap: disabling
[ 31.867257] avdd-io-edp-1v05: disabling
[ 31.867260] vdd-usb-hub-en: disabling
[ 643.916707] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 649.115712] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 649.925178] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 655.997844] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 688.908556] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 731.867087] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 784.880530] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 847.857432] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 910.773752] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 973.762212] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 1036.766719] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 1099.735041] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 1162.699897] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 1225.636408] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 1288.640726] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 1351.597375] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 1414.581741] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 1477.510459] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 1540.494900] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 1603.487406] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 1666.451974] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 1729.428255] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 1792.388866] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 1855.345315] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 1918.325867] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 1981.298463] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 2044.250844] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 2103.141872] extcon-disp-state extcon:disp-state: cable 51 state 0
[ 2103.141901] Extcon HDMI: HPD disabled
[ 2103.142137] tegradc tegradc.0: hdmi: unplugged
[ 2103.149443] tegradc tegradc.0: blank - powerdown
[ 2107.163588] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 2109.553964] tegradc tegradc.0: blank - powerdown
[ 2109.553981] tegradc tegradc.0: unblank
[ 2109.558647] tegradc tegradc.0: nominal-pclk:49000000 parent:48999316 div:1.00
[ 2109.558731] tegradc tegradc.0: hdmi: tmds rate:49000K prod-setting:prod_c_hdm
[ 2109.561417] tegradc tegradc.0: hdmi: get YCC quant from EDID.
[ 2109.596334] extcon-disp-state extcon:disp-state: cable 47 state 1
[ 2109.596336] Extcon AUX1(HDMI) enable
[ 2109.596541] extcon-disp-state extcon:disp-state: cable 51 state 1
[ 2109.596544] Extcon HDMI: HPD enabled
[ 2109.596571] tegradc tegradc.0: hdmi: plugged
[ 2109.610977] tegradc tegradc.0: blank - powerdown
[ 2109.661662] extcon-disp-state extcon:disp-state: cable 47 state 0
[ 2109.661664] Extcon AUX1(HDMI) disable
[ 2117.700891] tegra-xusb-padctl 7009f000.xusb_padctl: power down UTMI pad 1
[ 2117.701111] usb 1-2: USB disconnect, device number 2
[ 2117.834617] tegra-i2c 7000c700.i2c: no acknowledge from address 0x50
[ 2117.842818] tegradc tegradc.0: hdmi: tegra_edid_read_block(0) returned err -1
[ 2117.842832] tegradc tegradc.0: hdmi_recheck_edid: read_edid_into_buffer() re1
[ 2117.842843] tegradc tegradc.0: hdmi: unable to read EDID
[ 2121.443260] tegra-xusb-padctl 7009f000.xusb_padctl: power on UTMI pads 1
[ 2121.541565] extcon-disp-state extcon:disp-state: cable 51 state 0
[ 2121.541604] Extcon HDMI: HPD disabled
[ 2121.541905] tegradc tegradc.0: hdmi: unplugged
[ 2121.554575] tegradc tegradc.0: blank - powerdown
[ 2121.704542] usb 1-2: new full-speed USB device number 5 using tegra-xusb
[ 2121.730286] usb 1-2: New USB device found, idVendor=0483, idProduct=5750
[ 2121.730350] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2121.730397] usb 1-2: Product: ByQDtech �触�控USB�鼠�标
[ 2121.730442] usb 1-2: Manufacturer: �深�圳�市�全�动�电�子�技�术�有�限�公�司
[ 2121.730483] usb 1-2: SerialNumber: DB17ECDCA9FC
[ 2121.739947] input: �深�圳�市�全�动�电�子�技�术�有�限�公�司 ByQDtech �触�控US3
[ 2121.740408] hid-multitouch 0003:0483:5750.0002: input,hidraw0: USB HID v1.100
[ 2122.164374] tegradc tegradc.0: blank - powerdown
[ 2122.164550] tegradc tegradc.0: unblank
[ 2122.180500] tegradc tegradc.0: nominal-pclk:49000000 parent:48999316 div:1.00
[ 2122.180692] tegradc tegradc.0: hdmi: tmds rate:49000K prod-setting:prod_c_hdm
[ 2122.181688] tegradc tegradc.0: hdmi: get YCC quant from EDID.
[ 2122.219099] extcon-disp-state extcon:disp-state: cable 47 state 1
[ 2122.219109] Extcon AUX1(HDMI) enable
[ 2122.219709] extcon-disp-state extcon:disp-state: cable 51 state 1
[ 2122.219713] Extcon HDMI: HPD enabled
[ 2122.224847] tegradc tegradc.0: hdmi: plugged
[ 2122.232906] tegradc tegradc.0: blank - powerdown
[ 2122.298835] extcon-disp-state extcon:disp-state: cable 47 state 0
[ 2122.298837] Extcon AUX1(HDMI) disable
[ 2170.152116] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)
[ 2233.156756] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), s)