Unknown problem using driver - blank screen

Graphics / Linux Linux
1

Hi!

Tried recent NVidia driver 331.20 and latest linux(OpenSuSE 13.1 x86_64).

Installed driver, made config, as was told in manual, but in attempt to run Xorg appears blank screen and story ends… Tried to figure out, what’s wrong with it, but had no luck.

  1. Here is a xorg.conf contents:
Section "ServerLayout"
    Identifier "layout"
    Screen 0 "nvidia"
    Inactive "intel"
EndSection

Section "Device"
    Identifier "nvidia"
    Driver "nvidia"
    BusID "PCI:1:0:0"
EndSection

Section "Screen"
    Identifier "nvidia"
    Device "nvidia"
    Option "AllowEmptyInitialConfiguration"
EndSection

Section "Device"
    Identifier "intel"
    Driver "modesetting"
EndSection

Section "Screen"
    Identifier "intel"
    Device "intel"
EndSection
  1. Then, here is a ~/.xinitrc
xrandr --setprovideroutputsource modesetting NVIDIA-0
xrandr --auto
  1. Here is a lspci output:
00:00.0 Host bridge: Intel Corporation 3rd Gen Core processor DRAM Controller (rev 09)
00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port (rev 09)
00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04)
00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04)
00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04)
00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04)
00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4)
00:1c.1 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 (rev c4)
00:1c.3 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 4 (rev c4)
00:1c.5 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 6 (rev c4)
00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04)
00:1f.0 ISA bridge: Intel Corporation HM77 Express Chipset LPC Controller (rev 04)
00:1f.2 RAID bus controller: Intel Corporation 82801 Mobile SATA Controller [RAID mode] (rev 04)
00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04)                                                                                                                                                                                 
01:00.0 VGA compatible controller: NVIDIA Corporation GF108M [GeForce GT 630M] (rev a1)                                                                                                                                                                                        
08:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5229 PCI Express Card Reader (rev 01)                                                                                                                                                                      
0a:00.0 Network controller: Intel Corporation Centrino Wireless-N 2230 (rev c4)                                                                                                                                                                                                
0b:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 07)

And finally here a bugreport file: http://parimkodu.eu/nvidia-bug-report.log.gz

2

PS. As only I installed OS “as is was” it was running dual card mode by default (intel + nouveau driver, as 3D accelerator). But nouveau is not the best option, and more over after installing and removing NVidia driver nouveau is no more used as a 3D accererator.

Any ideas what can be wrong and why doesn’t nvidia driver run as 3D accelerator?

And, ooops, I forgon to put put Xorg log, here it is: [url]http://parimkodu.eu/xorg.log[/url]

3

So, can someone help me?