|
Jetson AGX Orin Pinmux wakesource number
|
|
1
|
26
|
October 1, 2026
|
|
Correct PinMux Spreadsheet to use
|
|
5
|
1354
|
September 24, 2026
|
|
PEX_L10_CLKREQ_N Customer Usage dropdown only offers GPIO/unused — the SFIO function works when set by hand, so why does the sheet block it?
|
|
3
|
56
|
September 19, 2026
|
|
How to change pinmux by Pinmux Registers
|
|
1
|
41
|
September 17, 2026
|
|
Trying to port Pinmux excel file to a linux plain text plus script
|
|
5
|
100
|
August 19, 2026
|
|
How to get the XLS document to generate pin muxing for Jetson Orin NX?
|
|
1
|
82
|
July 30, 2026
|
|
UARTs other than UART1 and UART3 do not work
|
|
1
|
92
|
July 17, 2026
|
|
Jetson Thor pinmux spreadsheet generates .dtsi fragments but PINMUX_CONFIG expects .dts wrapper — documentation gap?
|
|
3
|
139
|
July 13, 2026
|
|
Orin nx,orin nano 核心板上接口定义的183管脚能否手动控制
|
|
3
|
136
|
July 8, 2026
|
|
How to disabled hpd pin in system
|
|
1
|
105
|
June 23, 2026
|
|
Jetson Orin NX - Unable to Configure GPIO07 as PWM7 Using Pinmux Spreadsheet
|
|
10
|
282
|
June 10, 2026
|
|
AGX Orin POR pin state when shutdown
|
|
4
|
150
|
May 27, 2026
|
|
First time flashing procedure when using custom carrier board
|
|
6
|
168
|
May 22, 2026
|
|
What is the key rules to config the custom pinmux on default official pinmux (Jetson orin nano) to flash custom pinmux
|
|
11
|
200
|
May 6, 2026
|
|
Generate DTSI file issue on Custom Pinmux config to flash custom jetson orin nano
|
|
13
|
176
|
May 4, 2026
|
|
How to flash the custom pinmux (custom dtsi)
|
|
6
|
188
|
May 1, 2026
|
|
PINMUX changes on MDIO and MDC jetson AGX Orin development kit
|
|
39
|
748
|
April 23, 2026
|
|
How to adjust bootloader version for pinmux modification
|
|
8
|
162
|
April 20, 2026
|
|
Jetson Thor's Pinmux Question
|
|
4
|
161
|
April 17, 2026
|
|
Technical guidance on this hardware-level pin configuration, M.2 single-sided module compatibility, and UART signal routing
|
|
3
|
120
|
April 1, 2026
|
|
Jetson AGX Orin, the DTS generated by pinmux spreadsheet unchanged
|
|
7
|
212
|
March 20, 2026
|
|
Is it normal for pinmux to lack an address after installing the system?
|
|
6
|
98
|
March 12, 2026
|
|
How to set PWM IO initial state to high level?
|
|
6
|
160
|
March 5, 2026
|
|
Pinmux template v1.1: cannot disable 3.3V tolerance after setting pin to Unused (cells protected)
|
|
4
|
148
|
March 3, 2026
|
|
Define at Pinmux a AON GPIO to be an Input does not take affect
|
|
3
|
123
|
March 3, 2026
|
|
If I need to modify the pinmux settings, which file should I replace?
|
|
10
|
239
|
March 3, 2026
|
|
SHUTDOWN_REQ* pin not driven low during shutdown
|
|
2
|
145
|
February 23, 2026
|
|
Generating Pinmux settings without Excel Macros
|
|
3
|
126
|
February 6, 2026
|
|
Can not find PADCTL_A0 = 0x810c282000
|
|
5
|
97
|
January 29, 2026
|
|
Pinmux generated .cfg question
|
|
5
|
184
|
January 2, 2026
|