I have run into a similar issue to this forum post, where a 4GB Jetson kit is stuck on the splash screen: Jetson Nano Developer Kit (4gb) doesn't boot after System Update (only shows Nvidia Logo) - #4 by domi The log dump appears to have an error in which the hardware thinks it’s the 2GB kit, but h…

The conclusion comes first. → This issue is not hardware problem. The board is fine. But to make it back to work, you have to flash it with sdkmanager. Below is the reason why this issue can only be resolved by using sdkmanager or our official flash script. It is long and not easy for beginner …

2nd board: failure-06.txt (20.7 KB)

3rd board: failure-06-1.txt (20.7 KB)

Hi santaimpersonator, [image] santaimpersonator: where a 4GB Jetson kit is stuck on the splash screen Are you using the devkit or custom board for Jetson Nano? If you are using the devkit, have you tried to flash the devkit with SDK Manager? What’s your power adapter for the board? Or you…

Hey Kevin, This is for the 4GB Jetson Nano dev kit: NVIDIA Jetson Nano Developer Kit (V3) - DEV-16271 - SparkFun Electronics I’m using a Jetpack 4.5 image for the Jetbot , which should be compatible with boards that have and do not have the updated firmware flashed on them. I have not tried using …

Hi, Please use latest sdcard image and try again. By default the kernel log in UART is in silent mode so if you could remove the quiet from /boot/extlinux/extlinux.conf, it might help.

The image I am using, appears the same as the one linked in the getting started guide: Getting Started With Jetson Nano Developer Kit | NVIDIA Developer

Then it requires further debug as I said. Need to enable full log.

Hey Wayne, I modified the /boot/extlinux/extlinux.conf file on the SD card and removed quiet from the APPEND label: extlinux.conf (839 Bytes) TIMEOUT 30 DEFAULT primary MENU TITLE L4T boot options LABEL primary MENU LABEL primary kernel LINUX /boot/Image INITRD /boot/initrd …

You can share some log to me so that I can check why this happened. If you are talking about nothing gets printed, then it must be setup issue. Bootloader log can be printed even without sdcard inserted. A change in some sdcard file won’t make it dead.

Boot Error - Stuck on splash screen

Robotics & Edge Computing Jetson Systems Jetson Nano

santaimpersonator April 14, 2023, 4:02am 2

Apparently, you can only attach one link per post. I’ll attach the log dumps from each board with this issue seperately:
failure-04.txt (20.7 KB)

Topic		Replies	Views
Problem with JetsonNano DevKit 4gb (wont boot) Jetson Nano boot	12	747	July 5, 2021
Jetson nano 4gb developtment kit B01 not booting Jetson Nano boot	21	346	November 24, 2025
Jetson Not Booting Jetson Nano boot , nano2gb	4	1091	June 23, 2022
Jetson Nano Bootloader Corrupted Jetson Nano boot , bootloader	12	326	August 4, 2025
Jetson Nano 2gb Won't Boot Beyond Nvidia Splash Screen Jetson Nano boot , nano2gb	7	5214	July 8, 2022
Nano 2GB won't boot past NVidia Splash Screen? Jetson Nano reflash	3	564	August 19, 2022
Jetson Nano fails to boot and cannot enter the system Jetson Nano boot	29	4375	January 24, 2022
Jetson 4GB Nano 4GB SDK does not boot Jetson Nano boot	27	2408	April 4, 2021
Jetson Nano 4GB stuck on splash screen with Jetpack 4.6.1 Jetson Nano jetpack	4	1112	April 15, 2022
Jetson Nano gets stuck at Nvidia logo. (Serial log from UART provided) Jetson Nano boot	3	625	July 13, 2022

Boot Error - Stuck on splash screen

Related topics