Hello, When I turn on the jetson tx2 using the dev kit it says cp: not writing through dangling symlink 'etc/resolv.config' /sbin/init: error while loading shared libraries: libip4tc.so.0: cannot open shared object file: No such file or directory and more outputs, I can share the whole output if …

Yes I have done that, thank you.

Please provide complete information as applicable to your setup. • Hardware Platform (Jetson / GPU) • DeepStream Version • JetPack Version (valid for Jetson only) • TensorRT Version • NVIDIA GPU Driver Version (valid for GPU only) • Issue Type( questions, new requirements, bugs) • How to repr…

I edited my question with more information. But as I can’t get into the OS I can’t get more information than that :/

I will note that JetPack 3.3.4 is quite old. Some forms of update (to new releases) were not supported on these older releases. Certain updates would cause boot failure, although the “dangling symlink” would not be a boot failure. It is possible that some libraries failing to load would not stop boo…

Thank you, I’ll check that. Here is the full console boot that I get and after a few seconds it reboots indefinitely. [image_67153153]

I’ll spend some time putting it in recovery mode and flash it with the current Jetpack release. Thank you

The serial console boot log is via the serial UART. This means the serial console program itself runs on another computer, and that program is able to log the entire boot (no screenshot needed, plus it shows all steps in boot, not just one screenshot). About all I can tell from the screenshot is th…

Please find the serial console attached. rebooting.txt (22.9 KB) Yes it is a TX dev kit I’m not using VM Yes, and the cable works fine for other jetson with the same TX dev kit.

I failed to enter force recovery mode using the provided instruction. For your information, I successfully flashed another Jetson TX2 with the Jetpack 4.6.3 but when I reboot it, it doesn’t start again, this is another issue with another jetson that could be related.

The log shows everything works up to and including load of the Linux kernel and device tree. It then fails immediately. This log line makes me suspect the root filesystem cannot be read: [ 1.683803] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00007f00 This is considerably les…

Can't turn on the jetson tx2 and can't flash it

Robotics & Edge Computing Jetson Systems Jetson TX2

KevinFFF February 2, 2023, 1:51am 6

Hi JaTxGPU,

Could you help to use SDK manager to update your TX2 devkit to current Jetson Linux R32.7.3 | NVIDIA Developer (Jetpack 4.6.3) release?

You could refer to the following instruction to enter force recovery mode and use manual setup in SDK manager to flash the board.
Cannot enter TX2 recovery mode - #2 by WayneWWW

Topic		Replies	Views
TX2 Flash Jetson OS error Jetson TX2 reflash	12	992	August 14, 2020
Jetson TX2 flash failed Jetson TX2 reflash	7	1024	May 26, 2021
Jet Pack installation jetson TX2 Jetson TX2 jetpack	27	1316	April 16, 2020
Jetson TX2 cannot enter recovery mode Jetson TX2 boot	38	1750	February 9, 2023
Flash Jetson TX2 error : CPU Bootloader is not running on device && Failed to execute commands with GenericInstaller Jetson TX2 reflash	29	5802	May 21, 2021
TX2 Flash Failed Jetson TX2	3	711	June 6, 2019
Flash issue - Flashing JETSON TX2 using sdk manager-jetpack 4.4 onto target OS HW Jetson TX2 sdkm	28	2180	January 17, 2021
TX2 won't boot from dev kit board Jetson TX2	28	1744	April 28, 2020
Jetson TX2 - Failed to flash device Jetson TX2	34	4217	May 20, 2019
TX2 not flashing image Jetson TX2 sdkm	12	880	January 3, 2022

Can't turn on the jetson tx2 and can't flash it

Related topics