Hi! I have an issue regarding my Jetson Nano. Apparently, I got a replacement from Nvidia just recently and tested it using a working SD Card (works on another Jetson Nano) but it doesn’t boot up and nothing appears on the screen. However, the green LED is lighted up and stays on. I chatted with the…

Actually, without a log, all I can tell are guessing… The possible causes are: this jetson nano has hardware problem. If this jetson nano is able to work before, and now it suddenly not work anymore. It means something corrupted the bootloader software. The factory does not install the boo…

You need to flash the board with sdkmanager. It seems you misunderstood the meaning of “factory reset”. That recovery mode is to put the board into a state that it can get reflashed by sdkmanager. There is no “just click a button and the board will be back to life magic”.

And some explanation to why flashing with sdkmanager will work. This post has nothing to do with your issue. Just need to check this comment. [image] Why jetson nano can't power on while adding FDT in /boot/extlinux/extlinux.conf? Jetson Nano Jetson nano sd module has two…

yes i factory reset the board and after that flashed using sdkmanager. But in the first place, before I factory reset the Jetson Nano, I do not understand why a working SD card does not work on the new Jetson Nano that I receive. It was unable to boot up at all but it is new.

And, I know just factory resetting the board doesn’t make it come back alive. That’s why I also flashed using the sdkmanager and even flashed a new OS image into the SD card.

Is the board able to work now or it is still dead?

Please dump the uart log. [image] Jetson Nano & NX Style - Serial Debug Console - JetsonHacks The Serial Debug Console is the most basic way to be able to interface with your Jetson Nano & NX Style Developer Kit. All it takes is a magic wire! Est. reading time: 7 minutes …

I don’t know either. It is not possible to tell if you cannot provide log. I flashed a new OS image to the board, will it not work? What kind of “flash” do you mean here? Sdkmanager or sdcard image? Generally, I use “flash” word only when using sdkmanager. I don’t consider sdcard image as a “…

I formatted the SD Card and also use the BalenaEtcher to write in a new image from your official website and slot it back into the Jetson Nano and tried to boot it up again.

Jetson Nano not working

Robotics & Edge Computing Jetson Systems Jetson Nano

megans0610 August 26, 2021, 3:49am 9

Hi, I do not have that cable to connect the serial port header. Yes, I tried it in campus a few weeks ago but I am unable to go back campus at the moment so I do not have a Linux host machine to run the sdkmanager. Currently, I flashed a new OS image to the board, will it not work?

How to recover my jetson nano B01,the board has dead?

Topic		Replies	Views
Jetson Nano unbootable Jetson Nano boot	9	961	March 14, 2023
Can't boot up Jetson Nano after flashing new image on SD card Jetson Nano boot	38	4377	August 1, 2022
Jetson Nano not booting up Jetson Nano boot	8	1059	September 15, 2021
Jeton nano not booting Jetson Nano boot	5	831	April 6, 2021
SD card no longer bootable Jetson Nano boot	5	991	February 3, 2022
Jetson Nano Won't power on Jetson Nano reflash	12	820	March 23, 2020
Problem with JetsonNano DevKit 4gb (wont boot) Jetson Nano boot	12	762	July 5, 2021
Jetson Nano Won't Boot Initially Jetson Nano boot , jetson , jetson-nano	4	702	October 18, 2023
Jetson Nano not booting Jetson Nano boot	5	2750	November 8, 2021
Jetson Nano doesn't boot Jetson Nano boot	9	903	February 14, 2022

Jetson Nano not working

Related topics