Hi i was working on UART followed as per this link But it didn’t work and after reboot Mouse and keyboard not working.

Also, are you really sure “ttyTHS1” on Xavier AGX is the port you want to use? Please be aware that Xavier AGX is not like NX which says their carrier board is compatible with each other.

Hi, Are you talking about that broken type C firmware board as the topic you filed yesterday?

Hi @WayneWWW , No its not that AGX. Today I was working on a different AGX. I was using UART but I wasn’t able to send or recieve any data so I reboted the AGX and this happened? these are the commands I used $ systemctl stop nvgetty $ systemctl disable nvgetty $ udevadm trigger Please Help t…

We are still checking if there is any fix for that issue. Please be patient. We don’t provide any call service here. What you should do is provide the correct log.

Hi @WayneWWW , As per our knowledge we have provided the correct logs so far, if you need any further we will be happy to provide the same.

You didn’t provide any log so far… what are you talking about …? Where is your dmesg??? If this new issue is different from that old topic, then you need to share the new log…

Do you have any device connected on your USB/eSATA port? If so, could you change it to other device and see if you will see same issue? Also, if you remove the device and connect nothing, will you see the same issue?

Hi @WayneWWW , There are no other devices connected in the USB port other than the Keyboard mous. I connected a media device and the same happened. 3.If there are no device there is a difference in the Log. I have attached the two logs below for your reference. Kindly have a look. demsg_uart_n…

Please reflash with pure jetpack to make sure this is software or hardware issue.

Hi @WayneWWW , We just flashed the Xavier and found out its working properly after flash. Thank you @WayneWWW . Please let me know about the other issues(from the other two Xaviers) once you find out the solution.

Usb usb2-port 3 cannot enable. maybe the usb cable is bad?

Robotics & Edge Computing Jetson Systems Jetson AGX Xavier

varun_pandithurai February 23, 2022, 9:33am 8

Hi @WayneWWW ,
I was talking about the logs which I provided you yesterday Regarding the two Xaviers in this Thread

I took the dmesg through SSH for this Xavier.
I have attached it here
dmesg_uart.log (76.0 KB)

Topic		Replies	Views
Nvidia Jetson AGX Xavier USB 3.0 Not Working Jetson AGX Xavier usb	14	1882	August 10, 2022
USB mouse and keyborad not working Jetson AGX Xavier usb	34	2482	March 1, 2022
Cannot open port USBtoUART driver ch341-uart Xavier-AGX Jetson AGX Xavier usb , jetson-inference	14	1902	September 18, 2021
USB Ports on Jetson AGX Xavier not working after setup Jetson AGX Xavier boot , ubuntu , usb	8	780	November 2, 2023
Jetson AGX Xavier USB Not Detected Jetson AGX Xavier	15	7405	December 29, 2019
USB ports stopped functioning Jetson AGX Xavier	1	463	February 19, 2020
USB 2 not working on custom Jetson Xavier AGX Jetson AGX Xavier usb , board-design	4	944	August 11, 2021
Usb not working after flash on AGX H01 kit Jetson AGX Xavier usb , board-design	5	1447	April 6, 2022
USB hub didn't work at Jetson AGX Xavier Jetson AGX Xavier	5	1262	July 8, 2019
USB Port Problems Jetson AGX Xavier	6	2239	September 17, 2018

Usb usb2-port 3 cannot enable. maybe the usb cable is bad?

Related topics