[0000.232] [L4T TegraBoot] (version 00.00.2018.01-l4t-b1625959)
[0000.238] Processing in cold boot mode Bootloader 2
[0000.243] A02 Bootrom Patch rev = 1023
[0000.246] Power-up reason: pmc por
[0000.249] No Battery Present
[0000.252] pmic max77620 reset reason
[0000.255] pmic max77620 NVERC : 0x40
[0000.259] RamCode = 0
[0000.261] Platform has DDR4 type RAM
[0000.264] max77620 disabling SD1 Remote Sense
[0000.269] Setting DDR voltage to 1125mv
[0000.273] Serial Number of Pmic Max77663: 0x1a0a36
[0000.280] Entering ramdump check
[0000.283] Get RamDumpCarveOut = 0x0
[0000.286] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8
[0000.292] Last reboot was clean, booting normally!
[0000.296] Sdram initialization is successful
[0000.300] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.306] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.312] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.318] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.324] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.330] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.336] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.341] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.358] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.364] Platform-DebugCarveout: 0
[0000.367] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.373] Non secure mode, and RB not enabled.
[0000.377] *** Booting BFS0.
[0000.379] Initialize FailControl
[0000.382] Read PT from (0:3)
[0000.398] Csd NumOfBlocks=0
[0000.437] PT crc32 and magic check passed.
[0000.441] Using BFS PT to query partitions
[0000.445] PT: Partition LNX NOT found !
[0000.449] *** Booting KFS0.
[0000.451] NvTbootFailControlDoFailover: No failover; Continuing ...
[0000.457] BoardID = 3448, SKU = 0x2
[0000.461] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0000.466] Read GPT from (0:3)
[0000.474] Using GPT Primary to query partitions
[0000.479] NvTbootFailControlDoFailover: No failover; Continuing ...
[0000.486] Loading Tboot-CPU binary
[0000.491] Verifying TBC in OdmNonSecureSBK mode
[0000.502] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.509] Bootloader downloaded successfully.
[0000.514] Downloaded Tboot-CPU binary to 0xa0000258
[0000.519] MAX77620_GPIO5 configured
[0000.522] CPU power rail is up
[0000.525] CPU clock enabled
[0000.528] Performing RAM repair
[0000.531] Updating A64 Warmreset Address to 0xa00002e9
[0000.536] BoardID = 3448, SKU = 0x2
[0000.540] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0000.546] NvTbootFailControlDoFailover: No failover; Continuing ...
[0000.552] Loading NvTbootBootloaderDTB
[0000.569] Verifying NvTbootBootloaderDTB in OdmNonSecureSBK mode
[0000.640] Bootloader DTB Load Address: 0x83000000
[0000.645] BoardID = 3448, SKU = 0x2
[0000.648] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0000.654] Loading NvTbootKernelDTB
[0000.681] Verifying NvTbootKernelDTB in OdmNonSecureSBK mode
[0000.752] Kernel DTB Load Address: 0x83100000
[0000.757] BoardID = 3448, SKU = 0x2
[0000.760] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0000.766] NvTbootFailControlDoFailover: No failover; Continuing ...
[0000.773] Loading cboot binary
[0000.785] Verifying EBT in OdmNonSecureSBK mode
[0000.827] Bootloader load address is 0x92c00000, entry address is 0x92c00258
[0000.833] Bootloader downloaded successfully.
[0000.838] BoardID = 3448, SKU = 0x2
[0000.841] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0000.847] NvTbootFailControlDoFailover: No failover; Continuing ...
[0000.853] PT: Partition NCT NOT found !
[0000.857] Warning: Find Partition via PT Failed
[0000.861] Next binary entry address: 0x92c00258
[0000.866] BoardId: 3448
[0000.870] Overriding pmu board id with proc board id
[0000.875] Display board id is not available
[0000.879] BoardID = 3448, SKU = 0x2
[0000.883] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0000.888] NvTbootFailControlDoFailover: No failover; Continuing ...
[0000.902] Verifying SC7EntryFw in OdmNonSecureSBK mode
[0000.992] /bpmp deleted
[0000.994] SC7EntryFw header found loaded at 0xff700000
[0001.402] OVR2 PMIC
[0001.404] Bpmp FW successfully loaded
[0001.407] BoardID = 3448, SKU = 0x2
[0001.411] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.417] NvTbootFailControlDoFailover: No failover; Continuing ...
[0001.424] WB0 init successfully at 0xff780000
[0001.428] Verifying NvTbootWb0 in OdmNonSecureSBK mode
[0001.433] Set NvDecSticky Bits
[0001.437] GSC2 address ff53fffc value c0edbbcc
[0001.443] GSC MC Settings done
[0001.446] BoardID = 3448, SKU = 0x2
[0001.449] Not Nano-SD or !QSPI-ONLY, check GPT table first ...
[0001.456] TOS Image length 53680
[0001.459] Monitor size 53680
[0001.462] OS size 0
[0001.467] Secure Os AES-CMAC Verification Success!
[0001.472] TOS image cipher info: plaintext
[0001.475] Loading and Validation of Secure OS Successful
[0001.491] SC7 Entry Firmware - 0xff700000, 0x4000
[0001.496] NvTbootPackSdramParams: start.
[0001.501] NvTbootPackSdramParams: done.
[0001.505] Tegraboot started after 162282 us
[0001.509] Basic modules init took 754336 us
[0001.513] Sec Bootdevice Read Time = 65 ms, Read Size = 3682 KB
[0001.519] Sec Bootdevice Write Time = 0 ms, Write Size = 0 KB
[0001.524] Next stage binary read took 7381 us
[0001.528] Carveout took -34773 us
[0001.531] CPU initialization took 652109 us
[0001.535] Total time taken by TegraBoot 1379053 us
[0001.540] Starting CPU & Halting co-processor
64NOTICE: BL31: v1.3(release):f9bf1e1
NOTICE: BL31: Built : 21:16:40, Jun 8 2023
ERROR: Error initializing runtime service trusty_fast
[0001.663] RamCode = 0
[0001.672] LPDDR4 Training: found 4 entries (2 nominal, 2 derated)
[0001.678] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0001.691] EMC Training Successful
[0001.694] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0001.706] EMC Training Successful
[0001.709] 408000 not found in DVFS table
[0001.750] RamCode = 0
[0001.756] DT Write: emc-table@204000 succeeded
[0001.763] DT Write: emc-table@1600000 succeeded
[0001.771] DT Write: emc-table-derated@204000 succeeded
[0001.780] DT Write: emc-table-derated@1600000 succeeded
[0001.785] LPDDR4 Training: Write DT: Number of tables = 4
[0001.836]
[0001.837] Debug Init done
[0001.840] Marked DTB cacheable
[0001.843] Bootloader DTB loaded at 0x83000000
[0001.848] Marked DTB cacheable
[0001.851] Kernel DTB loaded at 0x83100000
[0001.854] DeviceTree Init done
[0001.869] Pinmux applied successfully
[0001.874] gicd_base: 0x50041000
[0001.878] gicc_base: 0x50042000
[0001.881] Interrupts Init done
[0001.885] Using base:0x60005090 & irq:208 for tick-timer
[0001.890] Using base:0x60005098 for delay-timer
[0001.895] platform_init_timer: DONE
[0001.898] Timer(tick) Init done
[0001.902] osc freq = 38400 khz
[0001.906]
[0001.907] Welcome to L4T Cboot
[0001.910]
[0001.911] Cboot Version: 00.00.2018.01-t210-acb23272
[0001.916] calling constructors
[0001.919] initializing heap
[0001.922] initializing threads
[0001.925] initializing timers
[0001.928] creating bootstrap completion thread
[0001.932] top of bootstrap2()
[0001.935] CPU: ARM Cortex A57
[0001.938] CPU: MIDR: 0x411FD071, MPIDR: 0x80000000
[0001.943] initializing platform
[0001.997] Config for emmc ddr50 mode completed
[0002.002] sdmmc bdev is already initialized
[0002.006] Enable APE clock
[0002.008] Un-powergate APE partition
[0002.012] of_register: registering tegra_udc to of_hal
[0002.017] of_register: registering inv20628-driver to of_hal
[0002.023] of_register: registering ads1015-driver to of_hal
[0002.028] of_register: registering lp8557-bl-driver to of_hal
[0002.034] of_register: registering bq2419x_charger to of_hal
[0002.040] of_register: registering bq27441_fuel_gauge to of_hal
[0002.052] gpio framework initialized
[0002.056] of_register: registering tca9539_gpio to of_hal
[0002.061] of_register: registering tca9539_gpio to of_hal
[0002.067] of_register: registering i2c_bus_driver to of_hal
[0002.072] of_register: registering i2c_bus_driver to of_hal
[0002.078] of_register: registering i2c_bus_driver to of_hal
[0002.083] pmic framework initialized
[0002.087] of_register: registering max77620_pmic to of_hal
[0002.092] regulator framework initialized
[0002.096] of_register: registering tps65132_bl_driver to of_hal
[0002.102] initializing target
[0002.109] gpio_driver_register: register 'tegra_gpio_driver' driver
[0002.117] board ID = D78, board SKU = 2
[0002.124] fixed regulator driver initialized
[0002.145] initializing OF layer
[0002.148] NCK carveout not present
[0002.151] Skipping dts_overrides
[0002.156] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.175] I2C Bus Init done
[0002.177] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.188] I2C Bus Init done
[0002.191] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.202] I2C Bus Init done
[0002.205] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.216] I2C Bus Init done
[0002.218] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.229] I2C Bus Init done
[0002.232] of_children_init: Ops found for compatible string maxim,max77620
[0002.243] max77620_init using irq 118
[0002.248] register 'maxim,max77620' pmic
[0002.252] gpio_driver_register: register 'max77620-gpio' driver
[0002.259] of_children_init: Ops found for compatible string nvidia,tegra210-i2c
[0002.270] I2C Bus Init done
[0002.274] NCK carveout not present
[0002.285] Find /i2c@7000c000's alias i2c0
[0002.289] get eeprom at 1-a0, size 256, type 0
[0002.299] Find /i2c@7000c500's alias i2c2
[0002.302] get eeprom at 3-a0, size 256, type 0
[0002.307] get eeprom at 3-ae, size 256, type 0
[0002.311] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.317] I2C slave not started
[0002.320] I2C write failed
[0002.322] Writing offset failed
[0002.325] eeprom_init: EEPROM read failed
[0002.329] pm_ids_update: eeprom init failed
[0002.333] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.363] pm_ids_update: The pm board id is 3448-0002-401
[0002.370] Adding plugin-manager/ids/3448-0002-401=/i2c@7000c500:module@0x50
[0002.379] pm_ids_update: pm id update successful
[0002.384] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.414] eeprom_init: EEPROM incompatible version found
[0002.419] pm_ids_update: eeprom init failed
[0002.449] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.455] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0002.463] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0002.469] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0002.478] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:a7:d6:1b
[0002.484] Plugin Manager: Parse ODM data 0x000a4000
[0002.497] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x7
[0002.513] Find /i2c@7000c000's alias i2c0
[0002.517] get eeprom at 1-a0, size 256, type 0
[0002.527] Find /i2c@7000c500's alias i2c2
[0002.531] get eeprom at 3-a0, size 256, type 0
[0002.535] get eeprom at 3-ae, size 256, type 0
[0002.539] pm_ids_update: Updating 1,a0, size 256, type 0
[0002.545] I2C slave not started
[0002.548] I2C write failed
[0002.550] Writing offset failed
[0002.553] eeprom_init: EEPROM read failed
[0002.557] pm_ids_update: eeprom init failed
[0002.561] pm_ids_update: Updating 3,a0, size 256, type 0
[0002.592] pm_ids_update: The pm board id is 3448-0002-401
[0002.598] Adding plugin-manager/ids/3448-0002-401=/i2c@7000c500:module@0x50
[0002.605] pm_ids_update: pm id update successful
[0002.610] pm_ids_update: Updating 3,ae, size 256, type 0
[0002.640] eeprom_init: EEPROM incompatible version found
[0002.645] pm_ids_update: eeprom init failed
[0002.675] Add serial number:1424022046638 as DT property
[0002.683] Applying platform configs
[0002.691] platform-init is not present. Skipping
[0002.695] calling apps_init()
[0002.716] Found 17 GPT partitions in "sdmmc3_user"
[0002.721] Proceeding to Cold Boot
[0002.724] starting app android_boot_app
[0002.728] Device state: unlocked
[0002.731] display console init
[0002.741] could not find regulator
[0002.764] hdmi cable not connected
[0002.767] is_hdmi_needed: HDMI not connected, returning false
[0002.773] hdmi is not connected
[0002.776] sor0 isDT entry for leds-pwm not found
[0002.785] not supported
[0002.787] display_console_init: no valid display out_type
[0002.796] subnode volume_up is not found !
[0002.800] subnode back is not found !
[0002.803] subnode volume_down is not found !
[0002.807] subnode menu is not found !
[0002.811] Gpio keyboard init success
[0002.859] found decompressor handler: lz4-legacy
[0002.873] decompressing blob (type 1)...
[0002.939] display_resolution: No display init
[0002.943] Failed to retrieve display resolution
[0002.948] Could not load/initialize BMP blob...ignoring
[0002.953] -------> se_aes_verify_sbk_clear: 747
[0002.958] se_aes_verify_sbk_clear: Error
[0002.961] SE operation failed
[0002.964] bl_battery_charging: connected to external power supply
[0002.974] display_console_ioctl: No display init
[0002.979] switch_backlight failed
[0002.988] device_query_partition_size: failed to open partition sdmmc3_user:MS!
[0002.996] MSC Partition not found
[0003.005] device_query_partition_size: failed to open partition sdmmc3_user:US!
[0003.013] USP partition read failed!
[0003.016] blob_init: blob-partition USP header read failed
[0003.022] android_boot Unable to update recovery partition
[0003.027] kfs_getpartname: name = LNX
[0003.031] Loading kernel from LNX
[0003.120] load kernel from storage
[0003.130] decompressor handler not found
[0003.164] Successfully loaded kernel and ramdisk images
[0003.169] board ID = D78, board SKU = 2
[0003.174] display_resolution: No display init
[0003.178] Failed to retrieve display resolution
[0003.183] bmp blob is not loaded and initialized
[0003.187] Failed to display boot-logo
[0003.191] NCK carveout not present
[0003.194] Skipping dts_overrides
[0003.197] NCK carveout not present
[0003.209] Find /i2c@7000c000's alias i2c0
[0003.212] get eeprom at 1-a0, size 256, type 0
[0003.222] Find /i2c@7000c500's alias i2c2
[0003.226] get eeprom at 3-a0, size 256, type 0
[0003.231] get eeprom at 3-ae, size 256, type 0
[0003.235] pm_ids_update: Updating 1,a0, size 256, type 0
[0003.240] I2C slave not started
[0003.243] I2C write failed
[0003.246] Writing offset failed
[0003.249] eeprom_init: EEPROM read failed
[0003.253] pm_ids_update: eeprom init failed
[0003.257] pm_ids_update: Updating 3,a0, size 256, type 0
[0003.287] pm_ids_update: The pm board id is 3448-0002-401
[0003.294] Adding plugin-manager/ids/3448-0002-401=/i2c@7000c500:module@0x50
[0003.303] pm_ids_update: pm id update successful
[0003.307] pm_ids_update: Updating 3,ae, size 256, type 0
[0003.337] eeprom_init: EEPROM incompatible version found
[0003.343] pm_ids_update: eeprom init failed
[0003.373] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0003.379] shim_eeprom_update_mac:267: Failed to update 0 MAC address in DTB
[0003.387] eeprom_get_mac: EEPROM invalid MAC address (all 0xff)
[0003.393] shim_eeprom_update_mac:267: Failed to update 1 MAC address in DTB
[0003.401] updating /chosen/nvidia,ethernet-mac node 48:b0:2d:a7:d6:1b
[0003.408] Plugin Manager: Parse ODM data 0x000a4000
[0003.420] shim_cmdline_install: /chosen/bootargs: earlycon=uart8250,mmio32,0x7
[0003.429] Add serial number:1424022046638 as DT property
[0003.439] "bpmp" doesn't exist, creating
[0003.444] Updated bpmp info to DTB
[0003.450] Updated initrd info to DTB
[0003.453] "proc-board" doesn't exist, creating
[0003.459] Updated board info to DTB
[0003.462] "pmu-board" doesn't exist, creating
[0003.468] Updated board info to DTB
[0003.472] "display-board" doesn't exist, creating
[0003.478] Updated board info to DTB
[0003.481] "reset" doesn't exist, creating
[0003.486] Updated reset info to DTB
[0003.489] display_console_ioctl: No display init
[0003.494] display_console_ioctl: No display init
[0003.498] display_console_ioctl: No display init
[0003.503] Cmdline: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype
[0003.537] DTB cmdline: earlycon=uart8250,mmio32,0x70006000
[0003.543] boot image cmdline: root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4
[0003.559] Updated bootarg info to DTB
[0003.563] Adding uuid 00000001642c53031c0000000d0584c0 to DT
[0003.569] Adding eks info 0 to DT
[0003.575] WARNING: Failed to pass NS DRAM ranges to TOS, err: -7
[0003.581] Updated memory info to DTB
[0003.590] set vdd_core voltage to 1075 mv
[0003.594] setting 'vdd-core' regulator to 1075000 micro volts
[0003.600] Found secure-pmc; disable BPMP
U-Boot 2020.04-g4335beb (Jun 08 2023 - 21:16:44 -0700)
SoC: tegra210
Model: NVIDIA Jetson Nano Developer Kit
Board: NVIDIA P3450-0000
DRAM: 4 GiB
MMC: sdhci@700b0000: 1, sdhci@700b0600: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
MMC: no card present
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
894 bytes read in 27 ms (32.2 KiB/s)
1: primary kernel
Retrieving file: /boot/initrd
7159654 bytes read in 174 ms (39.2 MiB/s)
Retrieving file: /boot/Image
34707464 bytes read in 785 ms (42.2 MiB/s)
append: tegraid=21.1.2.0.0 ddr_die=4096M@2048M section=512M memtype=0 vpr_resiz
## Flattened Device Tree blob at 83100000
Booting using the fdt blob at 0x83100000
ERROR: reserving fdt memory region failed (addr=83410000 size=10000)
ERROR: reserving fdt memory region failed (addr=83400000 size=10000)
ERROR: reserving fdt memory region failed (addr=0 size=0)
ERROR: reserving fdt memory region failed (addr=0 size=0)
Using Device Tree in place at 0000000083100000, end 000000008317dfff
copying carveout for /host1x@50000000/dc@54200000...
copying carveout for /host1x@50000000/dc@54240000...
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.337-tegra (buildbrain@mobile-u64-5434-d8000) (3
[ 0.000000] Boot CPU: AArch64 Processor [411fd071]
[ 0.000000] OF: fdt:memory scan node memory@80000000, reg size 32,
[ 0.000000] OF: fdt: - 80000000 , 7ee00000
[ 0.000000] OF: fdt: - 100000000 , 7f200000
[ 0.000000] earlycon: uart8250 at MMIO32 0x0000000070006000 (options '')
[ 0.000000] bootconsole [uart8250] enabled
[ 1.116427] tegradc tegradc.1: dpd enable lookup fail:-19
[ 1.622178] Host read timeout at address 545c00c4
[ 1.883812] imx219 7-0010: imx219_board_setup: error during i2c read probe ()
[ 1.891456] imx219 7-0010: board setup failed
[ 1.919874] imx219 8-0010: imx219_board_setup: error during i2c read probe ()
[ 1.927449] imx219 8-0010: board setup failed
[ 1.953096] soctherm: OC ALARM 0x00000001
