|
Rshim[17469]: another backend already attached
|
|
2
|
303
|
May 23, 2022
|
|
Thinkpad P1 Gen 4 Ubuntu 18.04 not able to communicate with NVidia Driver
|
|
7
|
283
|
April 22, 2022
|
|
Ubuntu 20.04 NVIDIA Corporation Device 249d, Nvidia-Driver not work
|
|
1
|
372
|
April 1, 2022
|
|
Mellanox SN2010 no connectivity between two hosts on same subnet through L3 gateway on mellanox interface with VLAN.
|
|
1
|
149
|
February 14, 2022
|
|
Maximum number of TC flow offloads in Bluefield-II
|
|
4
|
226
|
January 4, 2022
|
|
VPI Configuration issue on SX6036G - Proxy-ARP does not come up
|
|
2
|
130
|
December 20, 2021
|
|
RSS doesn't work for Mellanox ConnectX-6 DX
|
|
2
|
328
|
December 13, 2021
|
|
DCQCN config with CX6
|
|
1
|
193
|
December 3, 2021
|
|
Why do Lossy RoCE Accelerations change RDMA Write {First, Middle, Last} to RDMA Write Only?
|
|
1
|
70
|
December 1, 2021
|
|
How to fix Mellanox BlueField-2 subnet interface keeping in PORT_INIT?
|
|
3
|
204
|
November 12, 2021
|
|
Mellanox SN2410 Issues
|
|
1
|
169
|
October 21, 2021
|
|
We have a Mellanox Technologies MT27630 Family and Mellanox Technologies MT27710 Family cards that has pre-set maximums RX 64 and TX 8192, is it possible to have the RX value increased?
|
|
3
|
50
|
August 31, 2021
|
|
Mellanox SN2010 MLAG configure issue
|
|
3
|
76
|
August 26, 2021
|
|
ConnectX.6DX Maximum number of TLS/IPSec offloads
|
|
1
|
162
|
August 5, 2021
|
|
questions about backup configuration switch SN2010 in rConfig
|
|
3
|
56
|
July 28, 2021
|
|
I need help with using InfiniBand in my data center
|
|
1
|
86
|
July 27, 2021
|
|
How to evaluate the eye information of Mellanox ConnectX-4 network card?
|
|
2
|
53
|
July 13, 2021
|
|
How is the LID assigned?
|
|
3
|
49
|
July 8, 2021
|
|
Connect X4 4117 adaptor cannot get throughput on Server 2019 DC more than 10Gbps. Adaptor connected to Dell s5048f-on switch.
|
|
1
|
47
|
June 30, 2021
|
|
What 10GbE link modes are supported by the MCX4121A-ACAT ConnectX-4 Lx EN NIC (25GbE Dual-Port SFP28) ?
|
|
3
|
104
|
May 12, 2021
|
|
Mellanox ConnectX-3 PRO ETH Driver MLNX_OFED_LINUX-5.0-2.1.8.0-ubuntu20.04-x86_64 does not allow Openstack Victoria VM DHCP after install the driver.
|
|
1
|
39
|
April 15, 2021
|
|
I need to upgrade the firmware in a Mellanox Card MT27800, they are installed in a ESXi running vpshere 6.7 u3 i tried to install the mft tool but i have this error L 'Could not find a trusted signer: certificate has expired'),
|
|
4
|
71
|
April 1, 2021
|
|
Did anyone observed a sudden/abrupt jump in performance while working with DPDK rxonly mode, from 11 queues to 12 queues in Mellanox ConnectX-5 100 GbE NIC
|
|
1
|
46
|
March 22, 2021
|
|
Error checking lossy RoCE acceleration state
|
|
2
|
119
|
December 31, 2020
|
|
How to aggregate CX5 VFs bandwidth in KVM
|
|
1
|
59
|
December 4, 2020
|
|
Do all NICs in the Mellanox ConnectX-6 DX portfolio enable Intel's DDIO?
|
|
2
|
161
|
November 24, 2020
|
|
How long should it take for an IB interface’s State to go from Down/Polling to Active/LinkUp? For a small, relatively new IB network we are waiting anywhere from 20 to 120 seconds for RHEL 7 hosted HCAs to become active.
|
|
1
|
120
|
November 20, 2020
|
|
HDR port limited to EDR
|
|
3
|
52
|
September 8, 2020
|
|
How can I test the Peer to Peer RDMA PCIe bandwidth between a single MLNX_CX5 NIC and a CUDA capable GPU
|
|
3
|
148
|
July 14, 2020
|
|
How to mapping PCIe (my Connect x5 NIC) to spesific NUMA node?
|
|
1
|
54
|
June 30, 2020
|