|
No ports opened from docker to localhost using jetson-containers
|
|
9
|
154
|
January 15, 2025
|
|
How to bring up the IB port
|
|
5
|
128
|
January 2, 2025
|
|
How to charge a NVDIA Jetson Xavier NX development kit version
|
|
3
|
19
|
October 7, 2024
|
|
Metropolis Microservices for Jetson Gen AI
|
|
1
|
98
|
July 12, 2024
|
|
WebSocket streaming: client can't connect, ERROR 404
|
|
2
|
475
|
March 4, 2024
|
|
Virtual UART serial console only working if the USB-C cable is connected before booting
|
|
14
|
611
|
October 25, 2023
|
|
Ports number mismatch - between /dev/videoN and argus_camera utility
|
|
2
|
607
|
April 25, 2023
|
|
Why i receive data in /ttyTHS1 while i connect external device to /ttyTHS2 in Jetson NANO?
|
|
19
|
2318
|
October 21, 2022
|
|
How to fix Mellanox BlueField-2 subnet interface keeping in PORT_INIT?
|
|
3
|
1127
|
November 12, 2021
|
|
Ibdump with connect-5: Failed to set port sniffer1: command interface bad param
|
|
3
|
2678
|
November 1, 2021
|
|
RoCEv2 is disabled on ConnectX-5 but the NIC still captures RoCEv2 packets.
|
|
4
|
2784
|
September 11, 2021
|
|
ConnectX5 ASAP2 OVS VXLAN offload + bond not working properly
|
|
5
|
1442
|
June 30, 2021
|
|
What 10GbE link modes are supported by the MCX4121A-ACAT ConnectX-4 Lx EN NIC (25GbE Dual-Port SFP28) ?
|
|
3
|
2333
|
May 12, 2021
|
|
How to configure reflective relay for layer2 switching for Mellanox switch SN2700
|
|
1
|
623
|
May 5, 2021
|
|
MLAG IPL link
|
|
1
|
1212
|
April 16, 2021
|
|
Unable to change mode to legacy mode - devlink fails on one port, hangs on the other.
|
|
1
|
977
|
April 3, 2021
|
|
I have 2 RDMA nics installed on this server. Ideally two netdevs per port for mlx5_0, example: ens224, ens225 each with their own mac addresses, but they both show up under a single "ens224".
|
|
1
|
691
|
January 20, 2021
|
|
Cable is detected but SX6036 shows port down
|
|
3
|
623
|
November 25, 2020
|
|
Management port routing
|
|
1
|
594
|
November 18, 2020
|
|
ib_register_client get wrong devices.
device->name print strange thing.
|
|
2
|
661
|
November 17, 2020
|
|
IPoIP sometimes fails. Is there any way to detect repair this automatically ?
|
|
1
|
614
|
October 27, 2020
|
|
MCX354A-QCBT both ports connected to a different host respectively.
iblinkinfo return with time out and lists only the connections for the first port.
|
|
7
|
950
|
October 7, 2020
|
|
HDR port limited to EDR
|
|
3
|
870
|
September 8, 2020
|
|
How to mapping PCIe (my Connect x5 NIC) to spesific NUMA node?
|
|
1
|
1463
|
June 30, 2020
|
|
ib_send_bw failing on CX5 port.
|
|
2
|
2018
|
June 9, 2020
|
|
Issue with ConnextX-6 SP in Dell R6525 (AMD EPYC 7542/7742)
|
|
2
|
674
|
May 19, 2020
|
|
Hello,
little pb with nvme-cli.
On client I try the command sudo sh -c 'nvme discover -t rdma -a 192.168.20.10 -s 4420'
but it returns:
Failed to write to /dev/nvme-fabrics: Argument invalide
|
|
1
|
544
|
March 15, 2020
|
|
In the "Raw Ethernet Programming: Basic Introduction - Code Example" post, when trying to run the receiver code, it fails when trying to create the qp. "I get Couldn't create RSS QP" and the code exits. Any thoughts on what might be wrong? Thanks.
|
|
1
|
956
|
March 4, 2020
|
|
How can I run MPI between different version of HCAs (eg. ConnectX-3 and ConnectX-4) in a subnet?
|
|
1
|
998
|
December 22, 2019
|
|
"MLX5 NIC: net_mlx5: port 0 cannot enable promiscuous mode: Cannot allocate memory"
Facing an issue with DPDK mlx5 with error in "promiscous mode" in MLX5 NIC card.
The Application initializes successfuly and the traffic/packets are not processed.
|
|
1
|
1101
|
November 18, 2019
|