Jetson & Embedded Systems Jetson TX2
| Topic | Replies | Views | Activity | |
|---|---|---|---|---|
|
Announcing JetPack 4.6.1 Release with L4T 32.7.1
We are pleased to announce JetPack 4.6.1 , a production release supporting Jetson AGX Xavier series, Jetson Xavier NX, Jetson TX2 series, Jetson TX1, and Jetson Nano. JetPack 4.6.1 is a minor update to JetPack 4.6 and i… |
|
4 | 2394 | August 14, 2022 |
|
Jetson Software Roadmap for 2H-2021 and 2022
NVIDIA continuously invests in JetPack and regularly ships software updates to enable performance improvements, new capabilities, and support for new modules and developer kits. In this announcement, we provide details a… |
|
5 | 6443 | May 28, 2021 |
|
TensorFlow for Jetson TX2!
Our official release of TensorFlow for Jetson TX2! Python 3.6+JetPack4.5 sudo apt-get install libhdf5-serial-dev hdf5-tools libhdf5-dev zlib1g-dev zip libjpeg8-dev liblapack-dev libblas-dev gfortran sudo apt-get instal… |
|
107 | 37842 | May 13, 2021 |
|
EOL Notice for NVIDIA Jetson TX2 Developer Kit
The Jetson TX2 Developer Kit will stop shipping from NVIDIA at the end of 2020. Distributors will continue to sell the developer kit while supplies last, so contact your distributor to discuss purchasing timelines. Jets… |
|
12 | 7989 | June 1, 2022 |
|
Links to Jetson TX2 Resources and Wiki
|
|
40 | 33184 | July 18, 2018 |
|
GMSL Camera - MAX9296A Deserializer Through USB
|
|
0 | 14 | October 5, 2022 |
|
CSI driver - interfere with gpio cells
|
|
0 | 16 | October 5, 2022 |
|
My customized device tree has gone after CSI driver installatoin
|
|
9 | 136 | October 5, 2022 |
|
./video_encode -fps param is invalid
|
|
0 | 13 | October 5, 2022 |
|
How to notice is disconnected my camera on my jetson tx2 board with use gstreamer?
|
|
0 | 16 | October 5, 2022 |
|
Jetson Tx2 mounts MP600 PRO LPX 4TB SSD，the write speed is only 14MB/S
|
|
4 | 62 | October 5, 2022 |
|
Ov5647 is not getting detected and driver is not loading in Jetson Nano
|
|
1 | 32 | October 5, 2022 |
|
Jetson Tx2 Board and TC358840 chip
|
|
5 | 808 | October 5, 2022 |
|
Image Based OTA TX2i
|
|
1 | 24 | October 5, 2022 |
|
How to enable SDMMC3 in u-boot on TX2-NX
|
|
4 | 111 | October 5, 2022 |
|
Jetson TX2 Power Monitoring Design
|
|
0 | 25 | October 4, 2022 |
|
253:0 thin pool : unknown target type
|
|
2 | 28 | October 4, 2022 |
|
4k 10bit HDR Hardware decode and encode on Jetson TX2 with ffmpeg
|
|
12 | 91 | October 4, 2022 |
|
Disable enable-power-down on tx2 nx
|
|
2 | 39 | October 4, 2022 |
|
Argus timing off when 2 cameras are present
|
|
3 | 75 | October 3, 2022 |
|
Error found in TX2 Boot: "nvdc: open: Permission denied" and ***NvRmMemInit failed***
|
|
18 | 279 | October 3, 2022 |
|
Assigning Static IP address to DHCP clients from Jetson Nano DHCPserver
|
|
1 | 37 | October 3, 2022 |
|
Synchronous video reading from seven port USB3.0 HUB
|
|
4 | 104 | October 3, 2022 |
|
TX2-4g R32.3.1 Failed at I2S0_RX sw reset
|
|
1 | 70 | October 3, 2022 |
|
Tx2-4g r32.3.1 i2s->bclk_ratio currupted
|
|
1 | 63 | October 3, 2022 |
|
How to set tx2nx i2s to slave mode and enable it?
|
|
1 | 56 | October 3, 2022 |
|
V4l2-compliance err VIDIOC_G/S_PARAM:FAILD on TX2.Use OH01A10 camera
|
|
3 | 77 | October 3, 2022 |
|
Stop code based on GStreamer signal status
|
|
1 | 56 | October 3, 2022 |
|
TX2i Thermal Paste Question
|
|
0 | 35 | October 2, 2022 |
|
NvBuffer to OpenCV GpuMat. Does memory is directly accessible to the device?
|
|
11 | 234 | October 2, 2022 |